-- Copyright (C) 2008-2014 Super Micro Computer Inc. All Rights Reserved -- $Id: fspb.mib,v 1.13 2012/09/07 09:52:05 siva Exp $ SUPERMICRO-PROVIDERBRIDGE-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE,MODULE-IDENTITY, Integer32, Unsigned32, Counter32, IpAddress, enterprises FROM SNMPv2-SMI RowStatus, MacAddress, TEXTUAL-CONVENTION FROM SNMPv2-TC VlanId, dot1qVlanIndex FROM Q-BRIDGE-MIB dot1adPepEntry FROM SUPERMICRO-DOT1AD-MIB EnabledStatus FROM P-BRIDGE-MIB; futureProviderBridgeMIB MODULE-IDENTITY LAST-UPDATED "201209050000Z" ORGANIZATION "Super Micro Computer Inc." CONTACT-INFO "support@Supermicro.com" DESCRIPTION "||||||" REVISION "201209050000Z" DESCRIPTION "||||||" ::= { enterprises supermicro-computer-inc(10876) super-switch(101) basic(1) 113} TunnelStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "To specify how to handle the L2 protocol packets received on a particular port. When the option is set to 'peer', the L2 protocol packets received on a particular port will be processed in the Bridge. When the option is set to 'tunnel', the L2 protocol packets received on a particular port will be transparently transmitted in the provider network and will not be processed in the Provider Bridges/Provider Edge Bridges. When the option is set to 'discard', the L2 protocol packets received over a particular port will not be processed and discarded." SYNTAX INTEGER { peer(1), tunnel(2), discard(3) } --Proprietary MIB implementation for the Provider Bridging functionality fsPbSystem OBJECT IDENTIFIER ::= { futureProviderBridgeMIB 1 } fsPbConfig OBJECT IDENTIFIER ::= { futureProviderBridgeMIB 2 } -- SCALAR BEGIN fsPbMulticastMacLimit OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "The Multicast MAC table size of the device. The upper limit value that can be SET for this object is limited by the underlying hardware. While on initialisation this object hold the maximum size of the Multicast MAC table of the device." ::= { fsPbSystem 1 } fsPbTunnelStpAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The MAC address to be used for Customer STP BPDUs tunneling inside Provider Network. When tunneling is enabled on a port, this MAC address will be used as the the destination MAC address of the customer BPDUs received on a port where STP tunneling is enabled and the outgoing port is a proprietary PNP. Inside Provider Network, the BPDUs received with this MAC address will be treated as data packets and not processed. When the BPDU is sent out of the Provider Network, this MAC address will be replaced with the reserved address defined for Customer STP BPDUs. This configuration is allowed only for Provider Core or Edge Bridges." ::= { fsPbSystem 2 } fsPbTunnelLacpAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The MAC address to be used for LACP packets tunneling inside Provider Network. When tunneling is enabled on a port, this MAC address will be used as the the destination MAC address of the customer LACP packets received over this port. Inside Provider Network, LACP packets received with this MAC address will be treated as data packets and not processed. When the tunneled LACP packets are sent out of the Provider Network, this MAC address will be replaced with the reserved address defined for LACP packets. This configuration is allowed only for Provider Core or Edge Bridges." ::= { fsPbSystem 3 } fsPbTunnelDot1xAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The MAC address to be used for Dot1x packets tunneling inside Provider Network. When tunneling is enabled on a port, this MAC address will be used as the the destination MAC address of the customer Dot1x packets received over this port. Inside Provider Network, Dot1x packets received with this MAC address will be treated as data packets and not processed. When the tunneled Dot1x packets are sent out of the Provider Network, this MAC address will be replaced with the reserved address defined for Dot1x packets. This configuration is allowed only when the Bridge is configured in Provider Code or Edge Bridge mode. This configuration is allowed only for Provider Core or Edge Bridges." ::= { fsPbSystem 4 } fsPbTunnelGvrpAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The MAC address to be used for GVRP PDUs tunneling inside Provider Network. When tunneling is enabled on a port, this MAC address will be used as the the destination MAC address of the customer GVRP PDUs received on a port where GVRP tunneling is enable and the outgoing port is a proprietary PNP. Inside Provider Network, GVRP PDUs received with this MAC address will be treated as data packets and not processed. When the tunneled GVRP PDUs are sent out of the Provider Network, this MAC address will be replaced with the reserved address defined for GVRP PDUs. This configuration is allowed only for Provider Core or Edge Bridges." ::= { fsPbSystem 5 } fsPbTunnelGmrpAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The MAC address to be used for GMRP PDUs tunneling inside Provider Network. When tunneling is enabled on a port, this MAC address will be used as the the destination MAC address of the customer GMRP PDUs received over this port. Inside Provider Network, GMRP PDUs received with this MAC address will be treated as data packets and not processed. When the tunneled GMRP PDUs are sent out of the Provider Network, this MAC address will be replaced with the reserved address defined for GMRP PDUs. This configuration is allowed only for Provider Core or Edge Bridges." ::= { fsPbSystem 6 } -- SCALAR END -- ------------------------------------------------------------- -- The Provider Bridge Port Type Configuration Table -- ------------------------------------------------------------- fsPbPortInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbPortInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing provider bridge releated configurations for the externally accessible ports. All the objects in this table are applicable only when the Bridge Mode is set as ProviderBridge or ProviderCoreBridge or ProviderEdgeBridge." ::= { fsPbConfig 1 } fsPbPortInfoEntry OBJECT-TYPE SYNTAX FsPbPortInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table specifies the Provider Bridge related port configurations. This table is indexed by ifIndex. " INDEX { fsPbPort } ::= { fsPbPortInfoTable 1 } FsPbPortInfoEntry ::= SEQUENCE { fsPbPort Integer32, fsPbPortSVlanClassificationMethod INTEGER, fsPbPortSVlanIngressEtherType Integer32, fsPbPortSVlanEgressEtherType Integer32, fsPbPortSVlanEtherTypeSwapStatus EnabledStatus, fsPbPortSVlanTranslationStatus EnabledStatus, fsPbPortUnicastMacLearning EnabledStatus, fsPbPortUnicastMacLimit Unsigned32, fsPbPortBundleStatus EnabledStatus, fsPbPortMultiplexStatus EnabledStatus } fsPbPort OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Index value of the port in the system for which this entry applies. The maximum index value of the port is defined by the system." ::= { fsPbPortInfoEntry 1 } fsPbPortSVlanClassificationMethod OBJECT-TYPE SYNTAX INTEGER { sourceMac (1), destinationMac (2), cvlanSrcMac (3), cvlanDstMac (4), dscp (5), cvlanDscp (6), sourceIp (7), destinationIp (8), srcIpDstIp (9), cvlanDstIp (10), cvlan (11), pvid (12) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the type of SVLAN classification that has to be used for a given type of port. providerNetworkPort / customerNetworkPort - Port's 'pvid' will be the SVLAN classification for the untagged packets received over this interface. customerEdgePort - The SVLAN classification mechanism is always based on 'cvlan' (i.e CVidRegistrationTable ).No other SVLAN classification mechanism is allowed for this port type. propCustomerNetworkPort / propCustomerEdgePort - 'pvid' will be default SVLAN classification mechanism for this port. But the user is free to configure any other SVLAN classification mechanism except the CVidRegistrationTable (ie cvlan mechanism) For proprietary CEP and proprietary CNP ports,the SVLAN classification is based on one of the configured SVLAN classification methods mentioned here. If it is not configured, by default the port's 'PVID' is considered as the SVLAN for untagged packets." ::= { fsPbPortInfoEntry 2 } fsPbPortSVlanIngressEtherType OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION " This object indicates the S-VLAN tag ether type used for the packets received on this port.Packets received on a port are considered tagged, when the packet ethertype matches with the port ether type configured. Otherwise, they will be considered untagged. By default, on all the ports, 0x88a8 will be configured as the ether type. On Proprietary Provider Network Ports 0x8100 will be configured as the ingress ethertype." DEFVAL { 34984 } ::= { fsPbPortInfoEntry 3 } fsPbPortSVlanEgressEtherType OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION " This object indicates the ether type of the S-VLAN tag that has to be applied for all the outgoing packets on this port. If a valid value is in this object, all the packets which are outgoing on this port will contain the ether type as configured in this object. By Default 0x88a8 will be used for packets transmitted with S-VLAN on the ports. On Proprietary Provider Network Ports and Customer Edge Ports, 0x8100 will be used as the ether type for the outgoing packets." DEFVAL { 34984 } ::= { fsPbPortInfoEntry 4} fsPbPortSVlanEtherTypeSwapStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION " This object indicates whether the Ether Type Swapping can be applied on the S-VLAN tagged packets over this port. The Ether type swapping will only be applied on S-VLAN tag of a packet. This configuration is applicable for all values of Port Type other than customer edge ports." DEFVAL { disabled } ::= { fsPbPortInfoEntry 5 } fsPbPortSVlanTranslationStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION " This object indicates whether the VID Translation table can be enabled on the incoming/outgoing packets on a particular port. The Service Vlan swapping is applicable only for the externally accesible network ports (ie) Provider Network Port ,Customer Network port and proprietary Customer Network Port. The Service Vlan Translation status can be enabled or disabled on per port basis. By default, it is enabled on Provider Network Port and Customer Network Port(S-Tagged) and disabled on the other applicable port-types." ::= { fsPbPortInfoEntry 6 } fsPbPortUnicastMacLearning OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS deprecated DESCRIPTION "A Truth value indicating the unicast MAC learning enabled/disabled status for this port. When Unicast Mac Learning is disabled, No Entry will be learned from the point of configuration on this port. When Mac Learning is enabled, Entries will be learned on this port." DEFVAL { enabled } ::= { fsPbPortInfoEntry 7 } fsPbPortUnicastMacLimit OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "The Limiting value on the number of distinct unicast destination MAC addresses that can be dynamically learnt over this interface. The lower limit and upper limit value that can be SET for this object is determined by the underlying hardware. This Limit is applicable for only dynamically learned entries and NOT for static unicast entries" ::= { fsPbPortInfoEntry 8 } fsPbPortBundleStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "A Truth value indicating that Bundling enabled/disabled on port, this Object can be enabled/disabled only for CEP. For other ports setting and getting is not meaningful." DEFVAL { enabled } ::= { fsPbPortInfoEntry 9 } fsPbPortMultiplexStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "A Truth value indicating that Bundling enabled/disabled on port, this Object can be enabled/disabled only for CEP. For other ports setting and getting is not meaningful." DEFVAL { enabled } ::= { fsPbPortInfoEntry 10 } -- ------------------------------------------------------------- -- The S-VLAN Port , SourceMAC based Configuration Table -- ------------------------------------------------------------- fsPbSrcMacSVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbSrcMacSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per port, per SourceMAC based Service VLAN classification information in the device. Entries can be configured into this table only when the bridge is configured as a Provider Bridge and the Port Type for this port is SET as Proprietary Customer Edge Port / Proprietary Customer Network Port." ::= { fsPbConfig 2 } fsPbSrcMacSVlanEntry OBJECT-TYPE SYNTAX FsPbSrcMacSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling Service VLAN classification at this specified port for an ingress frame with the specified Source MAC address in the ethernet header of the frame." INDEX { fsPbPort, fsPbSrcMacAddress } ::= { fsPbSrcMacSVlanTable 1 } FsPbSrcMacSVlanEntry ::= SEQUENCE { fsPbSrcMacAddress MacAddress, fsPbSrcMacSVlan VlanId, fsPbSrcMacRowStatus RowStatus } fsPbSrcMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Source MAC address present in the ethernet header of the frame received on this port for which Service VLAN is assigned based on this entry." ::= { fsPbSrcMacSVlanEntry 1 } fsPbSrcMacSVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-write STATUS current DESCRIPTION "The Service VLAN ID assigned to frames received on this port when the Source MAC address in the ethernet header of the frame is same as specified in this entry." ::= { fsPbSrcMacSVlanEntry 2 } fsPbSrcMacRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { fsPbSrcMacSVlanEntry 3 } -- ------------------------------------------------------------- -- The S-VLAN Port , DestinationMAC based Configuration Table -- ------------------------------------------------------------- fsPbDstMacSVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbDstMacSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per port, per Destination MAC based Service VLAN classification information in the device. Entries can be configured into this table only when the bridge is configured as a Provider Bridge. An entry in this table is possible only when the 'Port Type' for this port is SET as Proprietary Customer Network Port or Proprietary Customer Edge Port." ::= { fsPbConfig 3 } fsPbDstMacSVlanEntry OBJECT-TYPE SYNTAX FsPbDstMacSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling Service VLAN classification at this specified port for an ingress frame with the specified Destination MAC address in the ethernet header of the frame." INDEX { fsPbPort, fsPbDstMacAddress } ::= { fsPbDstMacSVlanTable 1 } FsPbDstMacSVlanEntry ::= SEQUENCE { fsPbDstMacAddress MacAddress, fsPbDstMacSVlan VlanId, fsPbDstMacRowStatus RowStatus } fsPbDstMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Destination MAC address present in the ethernet header of the frame received on this port for which Service VLAN is assigned based on this entry." ::= { fsPbDstMacSVlanEntry 1 } fsPbDstMacSVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-write STATUS current DESCRIPTION "The Service VLAN ID assigned to frames received on this port when the Destination MAC address in the ethernet header of the frame is same as specified in this entry." ::= { fsPbDstMacSVlanEntry 2 } fsPbDstMacRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is deleted when this object is SET 'destroy'." ::= { fsPbDstMacSVlanEntry 3 } -- ------------------------------------------------------------- -- The S-VLAN Port , C-VLAN, Source MAC based Configuration Table -- ------------------------------------------------------------- fsPbCVlanSrcMacSVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbCVlanSrcMacSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per Port, per Customer VLAN ID, per Source MAC based S-VLAN classification information in the device. Entries can be configured into this table only when the bridge is configured as a Provider Bridge. An entry in this table is possible only when the 'PortType' for this port is SET as Proprietary Customer Edge Port / Proprietary Customer Network Port." ::= { fsPbConfig 4 } fsPbCVlanSrcMacSVlanEntry OBJECT-TYPE SYNTAX FsPbCVlanSrcMacSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling Service VLAN classification at this specified port for an ingress frame with the classified Customer VLAN ID and with the specified Source MAC address in the ethernet header of the frame. Classification of Customer VLAN ID may be from the Customer VLAN tag in the received frame OR based on Port CVLAN table." INDEX { fsPbPort, fsPbCVlanSrcMacCVlan, fsPbCVlanSrcMacAddr } ::= { fsPbCVlanSrcMacSVlanTable 1 } FsPbCVlanSrcMacSVlanEntry ::= SEQUENCE { fsPbCVlanSrcMacCVlan VlanId, fsPbCVlanSrcMacAddr MacAddress, fsPbCVlanSrcMacSVlan VlanId, fsPbCVlanSrcMacRowStatus RowStatus } fsPbCVlanSrcMacCVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Customer VLAN ID in the Customer VLAN tag of an ingress frame at this specified port OR the Customer VLAN ID for which the ingress frame is classified to this specified port." ::= { fsPbCVlanSrcMacSVlanEntry 1 } fsPbCVlanSrcMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Source MAC address in the ethernet header of the frame received on this port." ::= { fsPbCVlanSrcMacSVlanEntry 2 } fsPbCVlanSrcMacSVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-write STATUS current DESCRIPTION "The Service VLAN assigned to frames received on this port, When the Classified Customer VLAN ID is same as specified in this entry and When the Source MAC address in the ethernet header of the frame is same as specified in this entry. Classification of Customer VLAN ID may be from the Customer VLAN tag in the received frame OR based on Port CVLAN table." ::= { fsPbCVlanSrcMacSVlanEntry 3 } fsPbCVlanSrcMacRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is deleted when this object is SET 'destroy'." ::= { fsPbCVlanSrcMacSVlanEntry 4 } -- ------------------------------------------------------------- -- The S-VLAN Port , C-VLAN, Destination MAC based Configuration Table -- ------------------------------------------------------------- fsPbCVlanDstMacSVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbCVlanDstMacSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per Port, per Customer VLAN ID, per Destination MAC based S-VLAN classification information in the device. Entries can be configured into this table only when the bridge is configured as a Provider Bridge. An entry in this table is possible only when the 'Port Type' for this port is SET as Proprietary Customer Edge Port / Proprietary Customer Network Port." ::= { fsPbConfig 5 } fsPbCVlanDstMacSVlanEntry OBJECT-TYPE SYNTAX FsPbCVlanDstMacSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling Service VLAN classification at this specified port for an ingress frame with the classified Customer VLAN ID and with the specified Destination MAC address in the ethernet header of the frame. Classification of Customer VLAN ID may be from the Customer VLAN tag in the received frame OR based on Port CVLAN table." INDEX { fsPbPort, fsPbCVlanDstMacCVlan, fsPbCVlanDstMacAddr } ::= { fsPbCVlanDstMacSVlanTable 1 } FsPbCVlanDstMacSVlanEntry ::= SEQUENCE { fsPbCVlanDstMacCVlan VlanId, fsPbCVlanDstMacAddr MacAddress, fsPbCVlanDstMacSVlan VlanId, fsPbCVlanDstMacRowStatus RowStatus } fsPbCVlanDstMacCVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Customer VLAN ID in the Customer VLAN tag of an ingress frame at this specified port or the Customer VLAN ID for which the ingress frame is classified for at this specified port." ::= { fsPbCVlanDstMacSVlanEntry 1 } fsPbCVlanDstMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Destination MAC address in the ethernet header of the frame received on this port." ::= { fsPbCVlanDstMacSVlanEntry 2 } fsPbCVlanDstMacSVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-write STATUS current DESCRIPTION "The Service VLAN assigned to frames received on this port when the Classified Customer VLAN ID and when the Destination MAC address in the ethernet header of the frame is same as specified in this entry. Classification of Customer VLAN ID may be from the Customer VLAN tag in the received frame OR based on Port CVLAN table." ::= { fsPbCVlanDstMacSVlanEntry 3 } fsPbCVlanDstMacRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is deleted when this object is SET 'destroy'." ::= { fsPbCVlanDstMacSVlanEntry 4 } -- ------------------------------------------------------------- -- The S-VLAN Port , DSCP based Configuration Table -- ------------------------------------------------------------- fsPbDscpSVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbDscpSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per port, per DiffServ Code Point (DSCP) value based Service VLAN classification information in the device. Entries can be configured into this table only when the bridge is configured as a Provider Bridge and the 'PortType' for this port is SET as Proprietary Customer Network Port or Proprietary Customer Edge Port." ::= { fsPbConfig 6 } fsPbDscpSVlanEntry OBJECT-TYPE SYNTAX FsPbDscpSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling Service VLAN classification at this specified port for an ingress IP frame with the DSCP value as specified in this entry." INDEX { fsPbPort, fsPbDscp } ::= { fsPbDscpSVlanTable 1 } FsPbDscpSVlanEntry ::= SEQUENCE { fsPbDscp Integer32, fsPbDscpSVlan VlanId, fsPbDscpRowStatus RowStatus } fsPbDscp OBJECT-TYPE SYNTAX Integer32 (0..63) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The DSCP value in the IP header of the frame received on this port for which Service VLAN is assigned based on this entry." ::= { fsPbDscpSVlanEntry 1 } fsPbDscpSVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-write STATUS current DESCRIPTION "The Service VLAN ID assigned to IP frames received on this port when the DSCP value in the IP header of the frame is same as specified in this entry." ::= { fsPbDscpSVlanEntry 2 } fsPbDscpRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is deleted when this object is SET 'destroy'." ::= { fsPbDscpSVlanEntry 3 } -- ------------------------------------------------------------- -- The S-VLAN Port ,C-VLAN and DSCP based Configuration Table -- ------------------------------------------------------------- fsPbCVlanDscpSVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbCVlanDscpSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per port, per Customer VLAN ID, per DiffServ Code Point (DSCP) value based Service VLAN classification information in the device. Entries can be configured into this table only when the bridge is configured as a Provider Bridge and the 'PortType' for this port is SET as Proprietary Customer Edge Port / Proprietary Customer Network Port." ::= { fsPbConfig 7 } fsPbCVlanDscpSVlanEntry OBJECT-TYPE SYNTAX FsPbCVlanDscpSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling Service VLAN classification at this specified port for an ingress IP frame with the classified Customer VLAN ID as specified in this entry and the DSCP value in the frame as specified in this entry. Classification of Customer VLAN ID may be from the Customer VLAN tag in the received frame OR based on Port CVLAN table." INDEX { fsPbPort, fsPbCVlanDscpCVlan, fsPbCVlanDscp } ::= { fsPbCVlanDscpSVlanTable 1 } FsPbCVlanDscpSVlanEntry ::= SEQUENCE { fsPbCVlanDscpCVlan VlanId, fsPbCVlanDscp Integer32, fsPbCVlanDscpSVlan VlanId, fsPbCVlanDscpRowStatus RowStatus } fsPbCVlanDscpCVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Customer VLAN ID in the Customer VLAN tag of an ingress frame at this specified port or the Customer VLAN ID for which the ingress frame is classified for at this specified port." ::= { fsPbCVlanDscpSVlanEntry 1 } fsPbCVlanDscp OBJECT-TYPE SYNTAX Integer32 (0..63) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The DSCP value in the IP header of the frame received on this port." ::= { fsPbCVlanDscpSVlanEntry 2 } fsPbCVlanDscpSVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-write STATUS current DESCRIPTION "The Service VLAN ID assigned to frames received on this port, when the classified Customer VLAN ID is the same as specified in this entry and when the DSCP value in the IP header of the frame is same as specified in this entry. Classification of Customer VLAN ID may be from the Customer VLAN tag in the received frame OR based on Port CVLAN table." ::= { fsPbCVlanDscpSVlanEntry 3 } fsPbCVlanDscpRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is deleted when this object is SET 'destroy'." ::= { fsPbCVlanDscpSVlanEntry 4 } -- ------------------------------------------------------------- -- The S-VLAN Port ,Source IP Address based Configuration Table -- ------------------------------------------------------------- fsPbSrcIpAddrSVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbSrcIpAddrSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per port, per Source IP Address, based Service VLAN classification information in the device. Entries can be configured into this table only when the bridge is configured as a Provider Bridge and the 'PortType' for this port is SET as Proprietary Customer Network Port or Proprietary Customer Edge Port." ::= { fsPbConfig 8 } fsPbSrcIpAddrSVlanEntry OBJECT-TYPE SYNTAX FsPbSrcIpAddrSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling Service VLAN classification at this specified port for an ingress IP frame with the Source IP Address in the IP header of the frame as specified in this entry." INDEX { fsPbPort, fsPbSrcIpAddr } ::= { fsPbSrcIpAddrSVlanTable 1 } FsPbSrcIpAddrSVlanEntry ::= SEQUENCE { fsPbSrcIpAddr IpAddress, fsPbSrcIpSVlan VlanId, fsPbSrcIpRowStatus RowStatus } fsPbSrcIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Source IP Address in the IP header of an ingress IP frame at this specified port." ::= { fsPbSrcIpAddrSVlanEntry 1 } fsPbSrcIpSVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-write STATUS current DESCRIPTION "The Service VLAN ID assigned to frames ingress at this port when the Source IP address in the IP header of the frame is same as specified in this entry." ::= { fsPbSrcIpAddrSVlanEntry 2 } fsPbSrcIpRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is deleted when this object is SET 'destroy'." ::= { fsPbSrcIpAddrSVlanEntry 3 } -- ------------------------------------------------------------- -- The S-VLAN Port ,Destination IP Address based Configuration Table -- ------------------------------------------------------------- fsPbDstIpAddrSVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbDstIpAddrSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per port, per Destination IP Address, based Service VLAN classification information in the device. Entries can be configured into this table only when the bridge is configured as a Provider Bridge and the 'PortType' for this port is SET as Proprietary Customer Network Port or Proprietary Customer Edge Port." ::= { fsPbConfig 9 } fsPbDstIpAddrSVlanEntry OBJECT-TYPE SYNTAX FsPbDstIpAddrSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling Service VLAN classification at this specified port for an ingress IP frame with the Destination IP Address in the IP header of the frame as specified in this entry." INDEX { fsPbPort, fsPbDstIpAddr } ::= { fsPbDstIpAddrSVlanTable 1 } FsPbDstIpAddrSVlanEntry ::= SEQUENCE { fsPbDstIpAddr IpAddress, fsPbDstIpSVlan VlanId, fsPbDstIpRowStatus RowStatus } fsPbDstIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Destination IP Address in the IP header of an ingress IP frame at this specified port." ::= { fsPbDstIpAddrSVlanEntry 1 } fsPbDstIpSVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-write STATUS current DESCRIPTION "The Service VLAN ID assigned to frames ingress at this port when the Destination IP address in the IP header of the frame is same as specified in this entry." ::= { fsPbDstIpAddrSVlanEntry 2 } fsPbDstIpRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is deleted when this object is SET 'destroy'." ::= { fsPbDstIpAddrSVlanEntry 3 } -- ------------------------------------------------------------- -- The S-VLAN Port ,SourceIP Address, DestinationIP Address based -- Configuration Table -- ------------------------------------------------------------- fsPbSrcDstIpSVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbSrcDstIpSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per port, per Source IP Address, per Destination IP Address based Service VLAN classification information in the device. Entries can be configured into this table only when the bridge is configured as a Provider Bridge and the'PortType' for this port is SET as Proprietary Customer Network Port or Proprietary Customer Edge Port." ::= { fsPbConfig 10} fsPbSrcDstIpSVlanEntry OBJECT-TYPE SYNTAX FsPbSrcDstIpSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling Service VLAN classification at this specified port for an ingress IP frame with the Source and Destination IP Address in the IP header of the frame as specified in this entry." INDEX { fsPbPort, fsPbSrcDstSrcIpAddr, fsPbSrcDstDstIpAddr } ::= { fsPbSrcDstIpSVlanTable 1 } FsPbSrcDstIpSVlanEntry ::= SEQUENCE { fsPbSrcDstSrcIpAddr IpAddress, fsPbSrcDstDstIpAddr IpAddress, fsPbSrcDstIpSVlan VlanId, fsPbSrcDstIpRowStatus RowStatus } fsPbSrcDstSrcIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Source IP Address in the IP header of an ingress IP frame at this specified port." ::= { fsPbSrcDstIpSVlanEntry 1 } fsPbSrcDstDstIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Destination IP Address in the IP header of an ingress IP frame at this specified port." ::= { fsPbSrcDstIpSVlanEntry 2 } fsPbSrcDstIpSVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-write STATUS current DESCRIPTION "The Service VLAN ID assigned to frames ingress at this port when the Source and Destination IP address in the IP header of the frame are same as specified in this entry." ::= { fsPbSrcDstIpSVlanEntry 3 } fsPbSrcDstIpRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is deleted when this object is SET 'destroy'." ::= { fsPbSrcDstIpSVlanEntry 4 } -- ------------------------------------------------------------- -- The S-VLAN Port ,Customer VLAN ID, Destination IP Address based -- Configuration Table -- ------------------------------------------------------------- fsPbCVlanDstIpSVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbCVlanDstIpSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per port, per Customer VLAN ID, per Destination IP Address, based Service VLAN classification information in the device. Entries can be configured into this table only when the bridge is configured as Provider Bridge or Provider Edge Bridge and the Port Type for this port is SET as Proprietary Customer Edge Port / Proprietary Customer Network Port." ::= { fsPbConfig 11 } fsPbCVlanDstIpSVlanEntry OBJECT-TYPE SYNTAX FsPbCVlanDstIpSVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling Service VLAN classification at this specified port for an ingress IP frame with the classified Customer VLAN ID as specified in this entry and the Destination IP Address in the IP header of the frame as specified in this entry. Classification of Customer VLAN ID may be from the Customer VLAN tag in the received frame OR based on Port CVLAN table." INDEX { fsPbPort, fsPbCVlanDstIpCVlan, fsPbCVlanDstIp } ::= { fsPbCVlanDstIpSVlanTable 1 } FsPbCVlanDstIpSVlanEntry ::= SEQUENCE { fsPbCVlanDstIpCVlan VlanId, fsPbCVlanDstIp IpAddress, fsPbCVlanDstIpSVlan VlanId, fsPbCVlanDstIpRowStatus RowStatus } fsPbCVlanDstIpCVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Customer VLAN ID in the Customer VLAN tag of an ingress frame at this specified port or the Customer VLAN ID for which the ingress frame is classified for at this specified port." ::= { fsPbCVlanDstIpSVlanEntry 1 } fsPbCVlanDstIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Destination IP Address in the IP header of an ingress IP frame at this specified port." ::= { fsPbCVlanDstIpSVlanEntry 2 } fsPbCVlanDstIpSVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-write STATUS current DESCRIPTION "The Service VLAN ID assigned to frames ingress at this port when the classified Customer VLAN ID is same as specified in this entry and the Destination IP address in the IP header of the frame is same as specified in this entry. Classification of Customer VLAN ID may be from the Customer VLAN tag in the received frame OR based on Port CVLAN table." ::= { fsPbCVlanDstIpSVlanEntry 3 } fsPbCVlanDstIpRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is deleted when this object is SET 'destroy'." ::= { fsPbCVlanDstIpSVlanEntry 4 } -- ------------------------------------------------------------- -- The C-VLAN Port based Configuration Table -- ------------------------------------------------------------- fsPbPortBasedCVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbPortBasedCVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing Customer Edge Port / Proprietary Customer Edge Port / Proprietary Customer Network Port mapping to Customer VLAN on a providerBridge. This table is used for a classifying a untagged frame received on above mentioned customer ports." ::= { fsPbConfig 12 } fsPbPortBasedCVlanEntry OBJECT-TYPE SYNTAX FsPbPortBasedCVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An Entry in this table will be created whenever a port is configured as Customer Edge Port / Proprietary Customer Edge Port / Proprietary Customer Network Port.This Entry will be used on the ingress frame on the specified ports based on enabled status for classifying the frame to CVLAN. Also the Entry will be deleted in this table, when the port type is modified anything other than the specified one." INDEX { fsPbPort } ::= { fsPbPortBasedCVlanTable 1 } FsPbPortBasedCVlanEntry ::= SEQUENCE { fsPbPortCVlan VlanId, fsPbPortCVlanClassifyStatus EnabledStatus } fsPbPortCVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-write STATUS current DESCRIPTION "The Customer VLAN ID assigned to untagged frames ingress at this specified Customer Edge Port / Proprietary Customer Edge Port / Proprietary Customer Network Port." ::= { fsPbPortBasedCVlanEntry 1 } fsPbPortCVlanClassifyStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicate C-VLAN classification status on a port. This Object can be enabled/disabled only for PropCEP/PropCNP. For CEP, this object cannot be disabled." DEFVAL { enabled } ::= { fsPbPortBasedCVlanEntry 2 } -- ------------------------------------------------------------- -- EtherType SwappingTable -- ------------------------------------------------------------- fsPbEtherTypeSwapTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbEtherTypeSwapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Table containing the Translation information of the ethertype for a Service VLAN in a given packet. This Table shall be used only at ingress and NOT at egress of the Customer Network Port / Proprietary Customer Network Port / Provider Network Port. This translation table is applicable for only Service VLAN and not for customer VLAN's." ::= { fsPbConfig 13 } fsPbEtherTypeSwapEntry OBJECT-TYPE SYNTAX FsPbEtherTypeSwapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry containing the Local and Relay Ether type for a given packet on a particular port. This entry shall be applicable on all types of ports if and only if fsPbPortSVlanEtherTypeSwapStatus is Enabled on that Port." INDEX { fsPbPort, fsPbLocalEtherType} ::= { fsPbEtherTypeSwapTable 1 } FsPbEtherTypeSwapEntry ::= SEQUENCE { fsPbLocalEtherType Integer32, fsPbRelayEtherType Integer32, fsPbEtherTypeSwapRowStatus RowStatus } fsPbLocalEtherType OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Ether type present in the service vlan tag of the ingress packet at the given port." ::= { fsPbEtherTypeSwapEntry 1 } fsPbRelayEtherType OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The Relay Ether type mapped for the ether type present in the local service vlan tag of the ingress packet at the given port." ::= { fsPbEtherTypeSwapEntry 2 } fsPbEtherTypeSwapRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { fsPbEtherTypeSwapEntry 3 } -- ---------------------------------------------------------------- -- S-VLAN configuration table -- ---------------------------------------------------------------- fsPbSVlanConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbSVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table to configure the service type supported by an S-VLAN. Based on the service type configured for the S-VLAN, the oper point-to-point state of PEP ports will be determined." ::= { fsPbConfig 14 } fsPbSVlanConfigEntry OBJECT-TYPE SYNTAX FsPbSVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " The service type can be configured for an S-VLAN only when the VLAN is already created in the system." INDEX {dot1qVlanIndex} ::= { fsPbSVlanConfigTable 1 } FsPbSVlanConfigEntry ::= SEQUENCE { fsPbSVlanConfigServiceType INTEGER } fsPbSVlanConfigServiceType OBJECT-TYPE SYNTAX INTEGER { eLine (1), eLan (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The object to specify the service type supported by the S-VLAN. When it is set to 'eLine', the S-VLAN connects not more than two customer interfaces. If the service type for a vlan is 'eLine', then learning member ports through GVRP will not be allowed. Hence the oper point-to-point state of the PEPs connecting the S-VLAN can be set to True. When it is set to 'eLan', the S-VLAN connects more than two customer interfaces.So the oper point-to-point state of the PEPs connecting the S-VLAN will be set to False. In case of IVL, When the service type is set to E-Line for a VLAN, the MAC learning status will be set to 'disabled'. When it is set to E-LAN, MAC learning status will be enabled for that VLAN." ::= { fsPbSVlanConfigEntry 1 } -- ---------------------------------------------------------------- -- Tunnel protocol configuration table -- ---------------------------------------------------------------- fsPbTunnelProtocolTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbTunnelProtocolEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This table contains information about the handling (Tunnel/Peer/ Discard)of customer Layer 2 protocols (STP/GVRP/GMRP/LACP/Dot1x and IGMP) inside service provider network. This table is supported only for Provider Core or Provider Edge Bridges." ::= { fsPbConfig 15 } fsPbTunnelProtocolEntry OBJECT-TYPE SYNTAX FsPbTunnelProtocolEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Entry indicating the handling (Tunnel/Peer/Discard) of Layer 2 protocols (STP/GVRP/GMRP/LACP/Dot1x and IGMP) on this port." INDEX { fsPbPort } ::= { fsPbTunnelProtocolTable 1 } FsPbTunnelProtocolEntry ::= SEQUENCE { fsPbTunnelProtocolDot1x TunnelStatus, fsPbTunnelProtocolLacp TunnelStatus, fsPbTunnelProtocolStp TunnelStatus, fsPbTunnelProtocolGvrp TunnelStatus, fsPbTunnelProtocolGmrp TunnelStatus, fsPbTunnelProtocolIgmp TunnelStatus } fsPbTunnelProtocolDot1x OBJECT-TYPE SYNTAX TunnelStatus MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The object to specify whether to peer/tunnel/discard the Dot1x packets received on this port." ::= { fsPbTunnelProtocolEntry 1 } fsPbTunnelProtocolLacp OBJECT-TYPE SYNTAX TunnelStatus MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The object to specify whether to peer/tunnel/discard the LACP packets received on this port." ::= { fsPbTunnelProtocolEntry 2 } fsPbTunnelProtocolStp OBJECT-TYPE SYNTAX TunnelStatus MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The object to specify whether to peer/tunnel/discard the STP packets received on this port." ::= { fsPbTunnelProtocolEntry 3 } fsPbTunnelProtocolGvrp OBJECT-TYPE SYNTAX TunnelStatus MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The object to specify whether to peer/tunnel/discard the GVRP packets received on this port." ::= { fsPbTunnelProtocolEntry 4 } fsPbTunnelProtocolGmrp OBJECT-TYPE SYNTAX TunnelStatus MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The object to specify whether to peer/tunnel/discard the GMRP packets received on this port." ::= { fsPbTunnelProtocolEntry 5 } fsPbTunnelProtocolIgmp OBJECT-TYPE SYNTAX TunnelStatus MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The object to specify whether to peer/tunnel/discard the IGMP packets received on this port." ::= { fsPbTunnelProtocolEntry 6 } -- ---------------------------------------------------------------- -- Tunnel protocol statistics table -- ---------------------------------------------------------------- fsPbTunnelProtocolStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbTunnelProtocolStatsEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This table contains statistics information about the tunneled Layer 2 protocols (STP/GVRP/GMRP/LACP/Dot1x and IGMP) received and transmitted over a port." ::= { fsPbConfig 16 } fsPbTunnelProtocolStatsEntry OBJECT-TYPE SYNTAX FsPbTunnelProtocolStatsEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Entry indicating the handling (Tunnel/Peer/Discard) of Layer 2 protocols (STP/GVRP/GMRP/LACP/Dot1x and IGMP) on this port. This table is supported only for Provider Core or Provider Edge Bridges." INDEX { fsPbPort } ::= { fsPbTunnelProtocolStatsTable 1 } FsPbTunnelProtocolStatsEntry ::= SEQUENCE { fsPbTunnelProtocolDot1xPktsRecvd Counter32, fsPbTunnelProtocolDot1xPktsSent Counter32, fsPbTunnelProtocolLacpPktsRecvd Counter32, fsPbTunnelProtocolLacpPktsSent Counter32, fsPbTunnelProtocolStpPDUsRecvd Counter32, fsPbTunnelProtocolStpPDUsSent Counter32, fsPbTunnelProtocolGvrpPDUsRecvd Counter32, fsPbTunnelProtocolGvrpPDUsSent Counter32, fsPbTunnelProtocolGmrpPktsRecvd Counter32, fsPbTunnelProtocolGmrpPktsSent Counter32, fsPbTunnelProtocolIgmpPktsRecvd Counter32, fsPbTunnelProtocolIgmpPktsSent Counter32 } fsPbTunnelProtocolDot1xPktsRecvd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of tunneled Dot1x Packets received." ::= { fsPbTunnelProtocolStatsEntry 1 } fsPbTunnelProtocolDot1xPktsSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of tunneled Dot1x Packets transmitted." ::= { fsPbTunnelProtocolStatsEntry 2 } fsPbTunnelProtocolLacpPktsRecvd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of tunneled LACP Packets received." ::= { fsPbTunnelProtocolStatsEntry 3 } fsPbTunnelProtocolLacpPktsSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of tunneled LACP packets transmitted." ::= { fsPbTunnelProtocolStatsEntry 4 } fsPbTunnelProtocolStpPDUsRecvd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of tunneled STP PDUs received." ::= { fsPbTunnelProtocolStatsEntry 5 } fsPbTunnelProtocolStpPDUsSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of tunneled STP PDUs transmitted." ::= { fsPbTunnelProtocolStatsEntry 6 } fsPbTunnelProtocolGvrpPDUsRecvd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of tunneled GVRP PDUs received." ::= { fsPbTunnelProtocolStatsEntry 7 } fsPbTunnelProtocolGvrpPDUsSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of tunneled GVRP PDUs transmitted." ::= { fsPbTunnelProtocolStatsEntry 8 } fsPbTunnelProtocolGmrpPktsRecvd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of tunneled GMRP PDUs packets received." ::= { fsPbTunnelProtocolStatsEntry 9 } fsPbTunnelProtocolGmrpPktsSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of tunneled GMRP packets transmitted." ::= { fsPbTunnelProtocolStatsEntry 10 } fsPbTunnelProtocolIgmpPktsRecvd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of tunneled IGMP packets received." ::= { fsPbTunnelProtocolStatsEntry 11 } fsPbTunnelProtocolIgmpPktsSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of tunneled IGMP packets transmitted." ::= { fsPbTunnelProtocolStatsEntry 12 } -- ---------------------------------------------------------------- -- Provider Edge Port configuration table -- ---------------------------------------------------------------- fsPbPepExtTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbPepExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is an extention of dot1adPepTable table, and it provides additional configurations to PEPs (like Cos Preservations,..). when a entry in dot1adPepTable is created, then an entry will be created in this table." ::= { fsPbConfig 17 } fsPbPepExtEntry OBJECT-TYPE SYNTAX FsPbPepExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry contains information like (COS preservation, ..) for the internal PEPs. Creation of an entry in this table is not allowed and only modification is allowed." AUGMENTS { dot1adPepEntry } ::= { fsPbPepExtTable 1 } FsPbPepExtEntry ::= SEQUENCE { fsPbPepExtCosPreservation EnabledStatus } fsPbPepExtCosPreservation OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to enable or disable COS preservation for a service provided by this PEP." DEFVAL { disabled } ::= { fsPbPepExtEntry 1 } END