-- SOCOMEC UPS MIB
-- UPS MIB 
--
-- { iso org(3) dod(6) internet(1) private(4) enterprises(1) socomecUPS(4555)
-- software(1) network(5) ups(1) }
-- ==============================================================================================

-- build on 5.01-5 from UPS MIB
-- vers. 1.00 creation
-- 24/07/2008 - NVO
--
-- THIS MIB INCLUDES ONLY UPS DATA (exept battery part)
--
-- The AdicomUnitObjects define the unit MIB version, dedicated for each unit in parallel

-- ==============================================================================================
-- Revision 1.01
-- 04/08/2008 - NVO
-- adding TRAP 10: Alarm cancelled
-- ==============================================================================================
-- ==============================================================================================
-- Revision 1.02
-- 12/11/2008 - NVO
-- UPS-SYS and UNIT data management update:
--      UPS-SYS info: means that these data are coming from a comprehensive view of all units (synthesis)
--                    or single unit data
--      UNIT info: means that the data are coming where the SNMP connection is located (unit 1 for example)
--              
-- UPS BATTERY STATUS (synthesis of every unit battery status)
-- Low=A011, Depleted=A012, Discharging=A010, Failure=A009 (include all units battery alarms)
-- 
-- UNIT BATTERY MEASUREMENTS
--
-- UNIT INPUT STATUS
--
-- UPS OUTPUT STATUS
--           standby(1): if all others conditions are false. Avoid using unit info   
--
-- UPS Bypass STATUS
--
-- UPS ALARMS
-- ==============================================================================================
-- ==============================================================================================
-- Revision 1.03
-- 11/02/2009 - NVO
-- On Battery TRAP management: as a standard TRAP.
-- adding: adicomUpsTrapTemperatureAlarm
-- ==============================================================================================
-- ==============================================================================================
-- Revision 1.04
-- 03/03/2009 - NVO
-- TrapTemperatureAlarm removed
-- Replaced by TrapLoadOnInverter
-- ==============================================================================================

SOCOMECUPS-ADICOM-MIB DEFINITIONS ::= BEGIN

IMPORTS
  DisplayString, TimeStamp, TimeInterval, TestAndIncr,
  AutonomousType
    FROM SNMPv2-TC
  enterprises
    FROM RFC1155-SMI
  OBJECT-TYPE
    FROM RFC-1212
  DisplayString
    FROM RFC1213-MIB
  TRAP-TYPE
    FROM RFC-1215;

PositiveInteger ::= INTEGER (1..2147483647)
NonNegativeInteger ::= INTEGER (1..2147483647)



socomecUPS         OBJECT IDENTIFIER ::= { enterprises 4555 }
software           OBJECT IDENTIFIER ::= { socomecUPS 1 }
network            OBJECT IDENTIFIER ::= { software 1 }
adicomUps          OBJECT IDENTIFIER ::= { network 5 }
adicomUpsObjects   OBJECT IDENTIFIER ::= { adicomUps 1 }
adicomUpsTraps     OBJECT IDENTIFIER ::= { adicomUps 2 }


adicomUpsIdent     OBJECT IDENTIFIER ::= { adicomUpsObjects 1 }
adicomUpsBattery   OBJECT IDENTIFIER ::= { adicomUpsObjects 2 }      
adicomUpsInput     OBJECT IDENTIFIER ::= { adicomUpsObjects 3 }      
adicomUpsOutput    OBJECT IDENTIFIER ::= { adicomUpsObjects 4 }      
adicomUpsBypass    OBJECT IDENTIFIER ::= { adicomUpsObjects 5 }
adicomUpsAlarm     OBJECT IDENTIFIER ::= { adicomUpsObjects 6 }
adicomUpsAgent     OBJECT IDENTIFIER ::= { adicomUpsObjects 7 }

-- ===========================================================================
--
-- adicomUpsIdentification
-- IdentModel = I000
-- IdentSerialNumber = I022
-- IdentFirmwareVersion = W001
-- IdentAgentSoftwareVersion = W005
-- ===========================================================================

adicomUpsIdentModel OBJECT-TYPE
      SYNTAX DisplayString (SIZE (0..63))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "The UPS Model designation."
      ::= { adicomUpsIdent 1 }

adicomUpsIdentSerialNumber OBJECT-TYPE
      SYNTAX DisplayString (SIZE(0..15))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "The UPS serial number"
      ::= { adicomUpsIdent 2 }

adicomUpsIdentFirmwareVersion OBJECT-TYPE
       SYNTAX DisplayString (SIZE (0..63))
       ACCESS read-only
       STATUS mandatory
       DESCRIPTION
           "The UPS firmware version."
      ::= { adicomUpsIdent 3 }

adicomUpsIdentAgentSoftwareVersion OBJECT-TYPE
      SYNTAX DisplayString (SIZE(0..31))
      ACCESS read-only
      STATUS mandatory
      DESCRIPTION
          "SNMP agent software version."
      ::= { adicomUpsIdent 4 }

-- ===========================================================================
--
-- UPS BATTERY STATUS
-- Low=A011, Depleted=A012, Discharging=A010, Failure=A009
--
-- UNIT BATTERY MEASUREMENTS
-- SecondOnBattery = M090 
-- EstimatedMinutesRemaining = M095 
-- EstimatedChargeRemaining = M094 
-- BatteryVoltage = (M082 + M083)
-- BatteryTemperature = M091
-- ===========================================================================

adicomUpsBatteryStatus OBJECT-TYPE
     SYNTAX     INTEGER {
           unknown(1),
           batteryNormal(2),
           batteryLow(3),
           batteryDepleted(4),
           batteryDischarging(5),
           batteryFailure(6)
     }
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "The battery status of the unit"
     ::= { adicomUpsBattery 1 }

adicomUpsSecondsOnBattery OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
        "If the unit is on battery power, the elapsed time
        since the unit last switched to battery power."
     ::= { adicomUpsBattery 2 }

adicomUpsEstimatedMinutesRemaining OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
        "An estimate of the time to battery charge depletion
        under the present load conditions."
     ::= { adicomUpsBattery 3 }

adicomUpsEstimatedChargeRemaining OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
        "An estimate of the battery charge remaining expressed
         as a percent of full charge."
     ::= { adicomUpsBattery 4 }

adicomUpsBatteryVoltage OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "The battery voltage in 0.1 Volt DC."
     ::= { adicomUpsBattery 5 }

adicomUpsBatteryTemperature OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "The temperature measurement inside the battery cabinet in 0.1 deg.C."
     ::= { adicomUpsBattery 6 }



-- ===========================================================================
--
-- UNIT INPUT STATUS
--
-- InputFrequency=M064
-- InputNumLines = 3 if (T014=0) else 1 phase ups
-- InputVoltage=M058,M059,M060
-- ===========================================================================


adicomUpsInputFrequency OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "Rectifier Input frequency in 0.1 HZ."
     ::= { adicomUpsInput 1 }


adicomUpsInputNumLines OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "The number of phases"
     ::= { adicomUpsInput 2 }


adicomUpsInputTable OBJECT-TYPE
    SYNTAX SEQUENCE OF AdicomUpsInputEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "A list of input table entries"
    ::= { adicomUpsInput  3 }


adicomUpsInputEntry OBJECT-TYPE
    SYNTAX AdicomUpsInputEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Array of measurements"
    INDEX { adicomUpsInputLineIndex }
    ::= { adicomUpsInputTable  1 }

AdicomUpsInputEntry ::= SEQUENCE {
             adicomUpsInputLineIndex INTEGER,
             adicomUpsInputVoltage INTEGER
             }

adicomUpsInputLineIndex OBJECT-TYPE
     SYNTAX INTEGER (0..65535)
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "Rectifier input phase number."
     ::= { adicomUpsInputEntry 1 }

adicomUpsInputVoltage OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "Rectifier input voltage in volts."
     ::= { adicomUpsInputEntry 2 }

-- ===========================================================================
--
-- UPS OUTPUT STATUS
-- normal=S000, bypass=S001, battery=A010, booster=notmanage, reduce=notmanage, ecomode=S006, esaver=S004
-- OutputFrequency = M009
-- OutputLoadRate = M023
-- OutputkVA= = M024
-- OutputNumLines = 4 if (T014=0)
-- OutputVoltage = M003,M004,M005
-- OutputCurrent = M006,M007,M008

-- ===========================================================================

adicomUpsOutputSource OBJECT-TYPE
     SYNTAX INTEGER {
           standby(1),
           none(2),
           normal(3),
           bypass(4),
           battery(5),
           booster(6),
           reducer(7),
           standby(8),
           eco-mode(9),
           e-saver(10)
     }
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "UPS load status"
     ::= { adicomUpsOutput 1 }


adicomUpsOutputFrequency OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "UPS Output frequency in 0.1 HZ."
     ::= { adicomUpsOutput 2 }

adicomUpsOutputLoadRate OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "UPS Output Load Rate in %."
     ::= { adicomUpsOutput 3 }

adicomUpsOutputkVA OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "UPS Output Power in kVA."
     ::= { adicomUpsOutput 4 }

adicomUpsOutputNumLines OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "Number of phases"
     ::= { adicomUpsOutput 5 }

adicomUpsOutputTable OBJECT-TYPE
    SYNTAX SEQUENCE OF AdicomUpsOutputEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "A list of input table entries."
    ::= { adicomUpsOutput  6 }

adicomUpsOutputEntry OBJECT-TYPE
    SYNTAX AdicomUpsOutputEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Array of measurements"
    INDEX { adicomUpsOutputLineIndex }
    ::= { adicomUpsOutputTable  1 }

AdicomUpsOutputEntry ::= SEQUENCE {
             adicomUpsOutputLineIndex INTEGER,
             adicomUpsOutputVoltage INTEGER,
             adicomUpsOutputCurrent INTEGER
             }

adicomUpsOutputLineIndex OBJECT-TYPE
     SYNTAX INTEGER (0..65535)
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "Output phase number."
     ::= { adicomUpsOutputEntry 1 }

adicomUpsOutputVoltage OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "Output voltage in volts."
     ::= { adicomUpsOutputEntry 2 }

adicomUpsOutputCurrent OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "Output current in Amps."
     ::= { adicomUpsOutputEntry 3 }

-- ===========================================================================
--
-- UPS Bypass STATUS
--
-- BypassFrequency=M031
-- BypassNumLines = 3 if (T014=0) else 1 phase ups
-- BypassVoltage=M028,M029,M030
-- ===========================================================================


adicomUpsBypassFrequency OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "Bypass Input frequency in 0.1 HZ."
     ::= { adicomUpsBypass 1 }


adicomUpsBypassNumLines OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "The number of phases"
     ::= { adicomUpsBypass 2 }


adicomUpsBypassTable OBJECT-TYPE
    SYNTAX SEQUENCE OF AdicomUpsBypassEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "A list of bypass table entries"
    ::= { adicomUpsBypass  3 }


adicomUpsBypassEntry OBJECT-TYPE
    SYNTAX AdicomUpsBypassEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Array of measurements"
    INDEX { adicomUpsBypassLineIndex }
    ::= { adicomUpsBypassTable  1 }

AdicomUpsBypassEntry ::= SEQUENCE {
             adicomUpsBypassLineIndex INTEGER,
             adicomUpsBypassVoltage INTEGER
             }

adicomUpsBypassLineIndex OBJECT-TYPE
     SYNTAX INTEGER (0..65535)
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "Bypass input supply phase number."
     ::= { adicomUpsBypassEntry 1 }

adicomUpsBypassVoltage OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "Bypass input voltage in volts."
     ::= { adicomUpsBypassEntry 2 }


-- ===========================================================================
--
-- UPS ALARMS
-- The alarm table is not manage in this case (?)
-- 
-- wellknown alarm list:
-- ImminentStop=A000
-- UpsOverload=A001
-- TransferImpossible=A002 or A003
-- InsufficientResource=A004
-- RedundancyLoss=A005
-- TemperatureAlarm=A013
-- GeneralAlarm=A015
-- ===========================================================================

adicomUpsWellKnownAlarms OBJECT IDENTIFIER ::= { adicomUpsAlarm  1 }

adicomUpsImminentStop OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "UPS Imminent Stop"
     ::= { adicomUpsWellKnownAlarms 1 }

adicomUpsOverload OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "UPS in overload"
     ::= { adicomUpsWellKnownAlarms 2 }

adicomUpsTransferImpossible OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "Transfer Impossible"
     ::= { adicomUpsWellKnownAlarms 3 }


adicomUpsInsufficientResource OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "The UPS hasn't the resource to supply the load."
     ::= { adicomUpsWellKnownAlarms 4 }

adicomUpsRedundancyLoss OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "The units are not any more redundant"
     ::= { adicomUpsWellKnownAlarms 5 }


adicomUpsTemperatureAlarm OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "The UPS or battery temperature is over the limits"
     ::= { adicomUpsWellKnownAlarms 6 }


adicomUpsGeneralAlarm OBJECT-TYPE
     SYNTAX INTEGER
     ACCESS read-only
     STATUS mandatory
     DESCRIPTION
         "UPS general alarm"
     ::= { adicomUpsWellKnownAlarms 7 }


-- ===========================================================================
-- adicomUpsAgent
--
-- Agent
-- ===========================================================================   
     
adicomUpsAgentTrapString OBJECT-TYPE
        SYNTAX DisplayString
        ACCESS read-only
        STATUS mandatory
        DESCRIPTION
                "This OID allows traps to be sent with an octet string argument"
        ::= { adicomUpsAgent 1 }


-- ===========================================================================
-- adicomUpsTraps
--
-- Traps group
-- TrapLoadOnInverter = S000
-- TrapOnBatteryPower = A010
-- TrapBatteryLow = A011 or A012
-- TrapPowerRestored = S013
-- TrapImminentStop = A000
-- TrapOverload = A001
-- TrapOutputLoadOFF = S003
-- TrapOutputOnBypass = S001
-- TrapGeneralAlarm = A015
-- TrapAlarmCancelled = all traps are no more active (level 1 to level 0)
-- ===========================================================================

   -- This section defines the well-known notifications sent by UPS
   -- Care must be taken to insure that no particular notification
   -- is sent to a single receiving entity more often than once
   -- every five seconds.

   adicomUpsTrapLoadOnInverter TRAP-TYPE
    ENTERPRISE adicomUpsTraps
    VARIABLES { adicomUpsAgentTrapString }
    DESCRIPTION
        "INFORMATION: Load protected and supplied by Inverter."
     ::= 1

   adicomUpsTrapOnBatteryPower TRAP-TYPE
    ENTERPRISE adicomUpsTraps
    VARIABLES { adicomUpsAgentTrapString }
    DESCRIPTION
        "WARNING: The UPS has switched to battery backup power."
     ::= 2

   adicomUpsTrapBatteryLow TRAP-TYPE
    ENTERPRISE adicomUpsTraps
    VARIABLES { adicomUpsAgentTrapString }
    DESCRIPTION
        "SEVERE: Battery is near to be discharged."      
     ::= 3

   adicomUpsTrapPowerRestored TRAP-TYPE
    ENTERPRISE adicomUpsTraps
    VARIABLES { adicomUpsAgentTrapString }
    DESCRIPTION
        "INFORMATION: Input power has been restored."
     ::= 4

   adicomUpsTrapImminentStop TRAP-TYPE
       ENTERPRISE adicomUpsTraps
       VARIABLES { adicomUpsAgentTrapString }
       DESCRIPTION
               "SEVERE: UPS Imminent Stop"
     ::= 5

   adicomUpsTrapOverload    TRAP-TYPE
       ENTERPRISE adicomUpsTraps
       VARIABLES { adicomUpsAgentTrapString }
       DESCRIPTION
               "SEVERE: UPS in Overload"
     ::= 6

   adicomUpsTrapOutputLoadOFF   TRAP-TYPE
       ENTERPRISE adicomUpsTraps
       VARIABLES { adicomUpsAgentTrapString }
       DESCRIPTION
               "WARNING: Load not supplied"
     ::= 7

   adicomUpsTrapOutputOnBypass  TRAP-TYPE
       ENTERPRISE adicomUpsTraps
       VARIABLES { adicomUpsAgentTrapString }
       DESCRIPTION
               "WARNING: Load supplied by automatic bypass"
     ::= 8
     
   adicomUpsTrapGeneralAlarm    TRAP-TYPE
       ENTERPRISE adicomUpsTraps
       VARIABLES { adicomUpsAgentTrapString }
       DESCRIPTION
               "WARNING: UPS general alarm"
     ::= 9   

   adicomUpsTrapAlarmCancelled    TRAP-TYPE
       ENTERPRISE adicomUpsTraps
       VARIABLES { adicomUpsAgentTrapString }
       DESCRIPTION
               "Alarm cancelled. UPS in normal situation"
     ::= 10   

END