-- ***************************************************************** -- RDN-CABLE-SPECTRUM-MIB.mib: -- Motorola's Cable Spectrum MIB -- -- Copyright (C) 1989, 2008 by Motorola, Inc. -- All rights reserved. -- ***************************************************************** RDN-CABLE-SPECTRUM-MIB DEFINITIONS ::= BEGIN IMPORTS riverdelta FROM RDN-MIB MODULE-IDENTITY, OBJECT-TYPE, Integer32, Unsigned32, Gauge32, Counter32, NOTIFICATION-TYPE FROM SNMPv2-SMI MacAddress, RowStatus, DateAndTime, TruthValue FROM SNMPv2-TC OBJECT-GROUP, MODULE-COMPLIANCE FROM SNMPv2-CONF InterfaceIndex, ifIndex, ifAdminStatus, ifOperStatus FROM IF-MIB ChannelList FROM DOCS-IF3-MIB; rdnCableSpectrum MODULE-IDENTITY LAST-UPDATED "201112300000Z" -- 30 DEC 2011 ORGANIZATION "Motorola" CONTACT-INFO "Motorola Customer Service 101 Tournament Drive Horsham, PA 19044 US Tel: +1 888 944 4357 Int Tel: +1 215 323 0044 Fax: +1 215 323 1502 Email: CPSSupport@Motorola.com" DESCRIPTION "This is the MIB Module for Cable Spectrum Management for MCNS compliant Cable Modem Termination Systems (CMTS). Copyright (C) 1989, 2008 by Motorola, Inc. All rights reserved." REVISION "200808080000Z" -- August 8, 2008 DESCRIPTION "Added Copyright Statement into MIB modules's description." REVISION "200508020000Z" -- 08 Aug 2005 DESCRIPTION "Adding rdnSpectrumAgilityStatisticsTable for Advanced Spectrum Management Frequency/Modulation Agility Feature" REVISION "200311050000Z" DESCRIPTION "Updated the CONTACT-INFO." REVISION "200307200000Z" DESCRIPTION "MIB compilation error where the next to last sub-identifier for the notifications is not zero. This can cause problem when notifications are translated to SMIv1 for SNMPv1. The previous versions of the notifications have been removed rather than obsoleting them because the MIB compilation errors would still have existed even with the notification in the obsolete status." REVISION "200306090000Z" DESCRIPTION "Fix MIB compiler error in the compliance statement." REVISION "201112300000Z" -- 30 DEC 2011 DESCRIPTION "Added new table rdnFlapCmtsCmUsStatusTable to show the CM flap parameters for US bonded CM." ::= { riverdelta 6 } rdnCableSpectrumObjects OBJECT IDENTIFIER ::= { rdnCableSpectrum 1 } rdnFlapObjects OBJECT IDENTIFIER ::= { rdnCableSpectrumObjects 1 } rdnFlapCmCmtsStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnFlapCmCmtsStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table keeps the status of the flap modems for per CMTS. This table applies to all CMTS card types. " ::= { rdnFlapObjects 1 } rdnFlapCmCmtsStatusEntry OBJECT-TYPE SYNTAX RdnFlapCmCmtsStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of attributes for an entry in the rdnFlapCmCmtsStatusTable." INDEX { flapCmCmtsIfIndex } ::= { rdnFlapCmCmtsStatusTable 1 } RdnFlapCmCmtsStatusEntry ::= SEQUENCE { flapCmCmtsIfIndex Integer32, flapListMaxSize Integer32, flapListCurrentSize Gauge32, flapAgingOutTime Integer32, flapInsertionTime Integer32, flapMissThreshold Integer32, flapPowerAdjThreshold Integer32, flapListPercentageThreshold INTEGER, flapListTrapEnable INTEGER } flapCmCmtsIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CMTS Interface Index." ::= { rdnFlapCmCmtsStatusEntry 1 } flapListMaxSize OBJECT-TYPE SYNTAX Integer32 (1..8191) UNITS "modems" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of flap modems. The user could configure this number according to the number of downstreams and the number of modem line cards in the CMTS. The number can range from 1 to 8191. The default value is 100. When the number of modems exceeds the max flap list size, the additional modems are ignored." DEFVAL { 100 } ::= { rdnFlapCmCmtsStatusEntry 2 } flapListCurrentSize OBJECT-TYPE SYNTAX Gauge32 (0..8191) UNITS "modems" MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of modems in the flap list. Its value will be less than or equal to flapListMaxSize." ::= { rdnFlapCmCmtsStatusEntry 3 } flapAgingOutTime OBJECT-TYPE SYNTAX Integer32 (1..86400) UNITS "minutes" MAX-ACCESS read-write STATUS current DESCRIPTION "The age out time in minutes for modems in the flap table. The number of minutes range from 1 to 86400. The default value is 1440." DEFVAL { 1440 } ::= { rdnFlapCmCmtsStatusEntry 4 } flapInsertionTime OBJECT-TYPE SYNTAX Integer32 (1..86400) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The interval of time that begins when the cable modem initially ranges, reboots, and ends when it starts initial maintenance again. If the interval of time is less than what is specified in flapInsertionTime, the flapCmInsertionFails and cmFlapCounts will increment. The valid range is from 1 to 86400 seconds. The default value is 60." DEFVAL { 60 } ::= { rdnFlapCmCmtsStatusEntry 5 } flapMissThreshold OBJECT-TYPE SYNTAX Integer32 (1..12) UNITS "modem" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum threshold for the number of consecutive miss counts during a polling cycle. If the flap miss counts goes over this threshold, the modem will be added into the flap list. Polling is maintained between the CMTS and the cable modem every 10 seconds. The flapMissThreshold specifies the maximum number of consecutive missed counts during one station maintenance poll interval. If there are more than 16 consecutive miss counts during one polling cycle, the modem will de-insert and attempt to range again. The value ranges from 1 to 12 consecutive counts. The default value is 6." DEFVAL { 6 } ::= { rdnFlapCmCmtsStatusEntry 6 } flapPowerAdjThreshold OBJECT-TYPE SYNTAX Integer32 (1..10) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION " The power adjustment threshold for a CM to raise and lower it's transmit power during normal operation. When a modem's power adjustment goes above or below the flapPowerAdjThreshold the CM will be added into the flap list. The flapCmPowerAdjustments and cmFlapCounts will be incremented as well. flapPowerAdjThreshold values of 2 dB and below are low enough to continuously increment the flapCmPowerAdjustments under normal conditions. The values range from 1 to 10. The default is 2. " DEFVAL { 2 } ::= { rdnFlapCmCmtsStatusEntry 7 } flapListPercentageThreshold OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION " The percentage CM miss threshold. If CM miss percentage goes over this threshold and flapListTrapEnable is set, a flap list trap will be send out to notify this event " DEFVAL {10} ::= { rdnFlapCmCmtsStatusEntry 8 } flapListTrapEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls flap list trap. If its value is set to enabled(1), a trap will be sent out when the CM miss percentage goes over the flapListPercentageThreshold; Otherwise no flap list trap will be sent out. By default, this object has the value enabled(1). " DEFVAL { enabled } ::= { rdnFlapCmCmtsStatusEntry 9 } -- The flap CM table holds the CM flap information for each CMTS rdnFlapCmTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnFlapCmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table keeps the records of modem state changes. An entry can be deleted from the table but can not be added to the table. This table applies to all CMTS card types. " ::= { rdnFlapObjects 2 } rdnFlapCmEntry OBJECT-TYPE SYNTAX RdnFlapCmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of attributes for an entry in the rdnFlapTable." INDEX { flapCmIndex } ::= { rdnFlapCmTable 1 } RdnFlapCmEntry ::= SEQUENCE { flapCmIndex INTEGER, cmtsIfIndex InterfaceIndex, flapCmMacAddress MacAddress, flapCmUpstreamChSet ChannelList, flapCmDownstreamChSet ChannelList, flapCmInsertionFails Counter32, flapCmHits Counter32, flapCmMisses Counter32, flapCmPowerAdjustments Counter32, cmFlapCounts Counter32, cmLastFlapTime DateAndTime, cmFlapCreateTime DateAndTime, cmFlapRowStatus RowStatus } flapCmIndex OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS not-accessible STATUS current DESCRIPTION " Index for Cable Modem." ::= { rdnFlapCmEntry 1 } cmtsIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The CMTS Interface Index." ::= { rdnFlapCmEntry 2 } flapCmMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "MAC address of the Cable Modem's Cable interface. Identifies a flap-list entry for a flapping Cable Modem." ::= { rdnFlapCmEntry 3 } flapCmUpstreamChSet OBJECT-TYPE SYNTAX ChannelList MAX-ACCESS read-only STATUS current DESCRIPTION "The list of the upstream channels.This shows the list of UCID's. The CMTS detects a flapping Cable Modem from its Cable upstream interface." ::= { rdnFlapCmEntry 4 } flapCmDownstreamChSet OBJECT-TYPE SYNTAX ChannelList MAX-ACCESS read-only STATUS current DESCRIPTION "The list of the downstream channels.This shows the list of DCID's." ::= { rdnFlapCmEntry 5 } flapCmInsertionFails OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "When the Cable Modem initially ranges, reboots and initially ranges again within the specified insertion time, this counter will increment. The cmFlapCounts increment along with this counter." REFERENCE "Data over Cable Radio Frequency Interface specification, Section 7.2." ::= { rdnFlapCmEntry 6 } flapCmHits OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the CMTS receives the Ranging request from the Cable Modem." ::= { rdnFlapCmEntry 7 } flapCmMisses OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the CMTS misses the Ranging request from the Cable Modem. The CMTS can check up to 16 consecutive times for a ranging request message during one polling cycle. Misses are not desirable since this is usually an indication of a return path problem; however, having a small number of misses is normal. Ideally, the Hit should be much greater than the Miss counts." ::= { rdnFlapCmEntry 8 } flapCmPowerAdjustments OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " When the power adjustment changed above or below the power adjustment threshold this counter will increment. The Flap Count (cmFlapCounts) will increment when this counter increments." REFERENCE "Data over Cable Radio Frequency Interface specification, Section 7.2." ::= { rdnFlapCmEntry 9 } cmFlapCounts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times a CM flaps Under following three situations, this counter will increase: (1) When flapCmInsertionFails is increased the flap counts will increase. (2) When the CMTS receives the number of consecutive misses specified in the flapMissThreshold, the flap counts will increase. (3) When flapPowerAdjustments is increased the flap counts will increase." REFERENCE "Data over Cable Radio Frequency Interface specification, Appendix B." ::= { rdnFlapCmEntry 10 } cmLastFlapTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The last time stamp cm flaps" ::= { rdnFlapCmEntry 11 } cmFlapCreateTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The time stamp when new flap CM is added to the table. " ::= { rdnFlapCmEntry 12 } cmFlapRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Controls and reflects the status of rows in this table. When a new flap cable modem is detected, and does not exist in flap list and flapListCurrentSize is less than flapListMaxSize, an entry will be created in this table. The instance of this object will be set to active(1). All flapping modems have the status of active(1). Active entries are removed from the table if they are aged out. The age out time is defined in flapAgingOutTime When a row is set to destroy(6), it will remove the entry immediately. To prevent an entry from being aged out, the entry should be set to notInService(2). The entry will remain in the table until this instance is set to destroy. The user is allowed set an entry from active to notInService or from notInService to destroy A user is not allowed to change a notInService entry to active. createAndGo(4) and createAndWait(5) are not supported." ::= { rdnFlapCmEntry 13 } flapTrapType OBJECT-TYPE SYNTAX INTEGER { power(1), ranging(2), insertion(3) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Reason for flapping power - The power threshold was exceeded. ranging - Missing ranging requests went beyond threshold insertion - Modem re-ranged within insertion time threshold. This is a place holder for the reason parameter for the modem to go into flap list. This should return ZERO when read. This just allows us to include a flapping reason in the modem flap trap varbind. " ::= { rdnFlapObjects 4 } -- -- rdnFlapCmtsCmUsStatusTable -- This table holds the CM logical channel flap parametrs in case of the upstream bonded modems. -- In case of Upstream bonded modems this table shows the flap stats of all the channels in bonding-group -- for upstream non-bonded modems, there is a table(rdnCmFlapTable) to show the flap stats. rdnFlapCmtsCmUsStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnFlapCmtsCmUsStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table holds the CM logical channel flap parameters incase of the US bonded modmes. This table applies to DOCSIS 3.0 CMTS card types. " ::= {rdnFlapObjects 5 } rdnFlapCmtsCmUsStatusEntry OBJECT-TYPE SYNTAX RdnFlapCmtsCmUsStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of attributes for an entry in the rdnFlapCmtsCmUsStatusTable." INDEX { rdnFlapCmtsCmIndex, rdnFlapCmtsCmUsIfIndex } ::= { rdnFlapCmtsCmUsStatusTable 1} RdnFlapCmtsCmUsStatusEntry ::= SEQUENCE { rdnFlapCmtsCmIndex INTEGER, rdnFlapCmtsCmUsIfIndex InterfaceIndex, rdnFlapCmtsCmMacAddress MacAddress, rdnFlapCmtsCmInsertionFails Counter32, rdnFlapCmtsCmHits Counter32, rdnFlapCmtsCmMisses Counter32, rdnFlapCmtsCmPowerAdjustments Counter32, rdnFlapCmtsCmFlapCounts Counter32 } rdnFlapCmtsCmIndex OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index for the cable modem registered on DOCSIS 3.0 CMTS card." ::= {rdnFlapCmtsCmUsStatusEntry 1} rdnFlapCmtsCmUsIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CMTS US channel interface index." ::= {rdnFlapCmtsCmUsStatusEntry 2} rdnFlapCmtsCmMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "MAC address of the US bonded Cable Modem. This identifies a flap-list entry for a flapping Cable Modem per logical channel." ::= {rdnFlapCmtsCmUsStatusEntry 3} rdnFlapCmtsCmInsertionFails OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "When the Cable Modem initially ranges, reboots and initially ranges again within the specified insertion time,this counter will increment. The cmFlapCounts increment along with this counter." ::= {rdnFlapCmtsCmUsStatusEntry 4} rdnFlapCmtsCmHits OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the CMTS receives the Ranging request from the Cable Modem." ::= {rdnFlapCmtsCmUsStatusEntry 5} rdnFlapCmtsCmMisses OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the CMTS misses the Ranging request from the Cable Modem. The CMTS can check up to 16 consecutive times for a ranging request message during one polling cycle." ::= {rdnFlapCmtsCmUsStatusEntry 6} rdnFlapCmtsCmPowerAdjustments OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "When the power adjustment changed above or below the power adjustment threshold this counter will increment." ::= {rdnFlapCmtsCmUsStatusEntry 7} rdnFlapCmtsCmFlapCounts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times a CM flaps Under following three situations. This counter will increase (1) When flapCmInsertionFails is increased the flap counts will increase. (2) When the CMTS receives the number of consecutive misses specified in the flapMissThreshold, the flap counts will increase. (3) When flapPowerAdjustments is increased the flap counts will increase." ::= {rdnFlapCmtsCmUsStatusEntry 8} -- NOTE: {rdnCableSpectrumObjects 2} is defined in RDN-SpectrumGroup.mib -- for Spectrum Group definitions (rdnCableSpectrumGroup) -- -- Frequency/Modulation Agility Statistics Table -- rdnSpectrumAgilityStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnSpectrumAgilityStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains statistics related to Advanced Spectrum Management's Frequency and Modulation Agility feature This table applies to all CMTS card types. For CMTS 2x8 cards, frequency and modulation agility hop decisions are made on the basis of SNR measurements. For older, 1x8 and 1x4 cards, hop decisions are made on the basis of error thresholds, or modem flapping. This table displays all upstream channels, regardless of whether they members of spectrum groups, or not. Agility actions can take place only for those channels belonging to spectrum groups that have hop actions configured. " ::= { rdnCableSpectrumObjects 3 } rdnSpectrumAgilityStatisticsEntry OBJECT-TYPE SYNTAX RdnSpectrumAgilityStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of objects in a row of rdnSpectrumAgilityStatisticsTable The index values for this table are the ifIndex values for upstream physical channels" INDEX { ifIndex } ::= { rdnSpectrumAgilityStatisticsTable 1 } RdnSpectrumAgilityStatisticsEntry ::= SEQUENCE { rdnSpectrumQualityCurrentChannelState INTEGER, rdnSpectrumQualityLastStateTransitionTime DateAndTime, rdnSpectrumQualityElapsedTimeCurrentState Unsigned32, rdnSpectrumQualityNumberStateTransitions Counter32, rdnSpectrumQualityResetStatistics TruthValue } rdnSpectrumQualityCurrentChannelState OBJECT-TYPE SYNTAX INTEGER { normal(1), impaired(2), pending(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current Channel Status: normal: channel quality is within rdnSnrThresholdValue. This is the optimum operational status of the channel. impaired: channel quality is below rdnSnrThresholdValue. The channel continues to operate is this state, but is degraded. If the channel remains in this state, it means that the quality of the spare spectrum is inadequate to allow a hop. pending: This is the operational status of the channel pending SNR signal quality assessment. The quality of the channel is unknown in this state. A channel will remain in this state, if no modems are registered and available for performing SNR measurement. When modems are available, then the channel will transition to either normal, or impaired, based on the SNR measurement." ::= { rdnSpectrumAgilityStatisticsEntry 1 } rdnSpectrumQualityLastStateTransitionTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "Timestamp indicating when rdnSpectrumQualityCurrentChannelState made its most recent transition" ::= { rdnSpectrumAgilityStatisticsEntry 2 } rdnSpectrumQualityElapsedTimeCurrentState OBJECT-TYPE SYNTAX Unsigned32 UNITS "tenths of seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Elapsed time in tenths of seconds that the channel has been in its current state (rdnSpectrumQualityCurrentChannelState)" ::= { rdnSpectrumAgilityStatisticsEntry 3 } rdnSpectrumQualityNumberStateTransitions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of transitions in rdnSpectrumQualityCurrentChannelState that have occurred since the time of system boot, or since the time of the last statistics reset (rdnSpectrumQualityResetStatistics)" ::= { rdnSpectrumAgilityStatisticsEntry 4 } rdnSpectrumQualityResetStatistics OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to TRUE(1) will reset rdnSpectrumQualityNumberStateTransitions. No other table objects are affected. A query of this object is not meaningful, but will always return FALSE" ::= { rdnSpectrumAgilityStatisticsEntry 5 } -- -- Notification group -- rdnCableSpectrumNotifications OBJECT IDENTIFIER ::= { rdnCableSpectrum 2 } rdnCableSpectrumNotificationPrefix OBJECT IDENTIFIER ::= { rdnCableSpectrumNotifications 0 } rdnFlapListNotification NOTIFICATION-TYPE OBJECTS { ifIndex, ifAdminStatus, ifOperStatus } STATUS current DESCRIPTION "a flap list trap signifies that SNMPv2 entity, acting in an agent role, has detected that the percentage of flap cm for one of the cmts board has gone over the flapListPercentageThreshold." ::= { rdnCableSpectrumNotificationPrefix 1 } rdnFlapModemNotification NOTIFICATION-TYPE OBJECTS { flapCmMacAddress, flapTrapType } STATUS current DESCRIPTION "This Trap will be sent whenever the modem goes into the flapping list for some reason. 'flapCmMacAddress' gives the Mac Address of the modem. 'flapTrapType' gives the cause for the modem to go into the flap list." ::= { rdnCableSpectrumNotificationPrefix 2 } -- -- Conformance statement -- rdnCableSpectrumConformance OBJECT IDENTIFIER ::= { rdnCableSpectrum 3 } rdnCableSpectrumCompliances OBJECT IDENTIFIER ::= { rdnCableSpectrumConformance 1 } rdnCableSpectrumGroups OBJECT IDENTIFIER ::= { rdnCableSpectrumConformance 2 } -- compliance statements compliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for devices that implement MCNS compliant Radio Frequency Interfaces and Spectrum Management features." MODULE -- rdnCableSpectrum MANDATORY-GROUPS { rdnFlapGroup, rdnAgilityGroup } ::= { rdnCableSpectrumCompliances 1 } -- units of conformance rdnFlapGroup OBJECT-GROUP OBJECTS { flapListMaxSize, flapListCurrentSize, flapAgingOutTime, flapInsertionTime, flapMissThreshold, flapPowerAdjThreshold, cmtsIfIndex, flapCmMacAddress, flapCmUpstreamChSet, flapCmDownstreamChSet, flapCmInsertionFails, flapCmHits, flapCmMisses, flapCmPowerAdjustments, cmFlapCounts, cmLastFlapTime, cmFlapCreateTime, cmFlapRowStatus, flapListPercentageThreshold, flapListTrapEnable } STATUS current DESCRIPTION "Group of objects implemented in Cable Modem Termination Systems providing Flap List information." ::= { rdnCableSpectrumGroups 1 } rdnAgilityGroup OBJECT-GROUP OBJECTS { rdnSpectrumQualityCurrentChannelState, rdnSpectrumQualityLastStateTransitionTime, rdnSpectrumQualityElapsedTimeCurrentState, rdnSpectrumQualityNumberStateTransitions, rdnSpectrumQualityResetStatistics } STATUS current DESCRIPTION "Group of objects implemented in Cable Modem Termination Systems providing Statistics for Frequency/Modulation Agility" ::= { rdnCableSpectrumGroups 2 } END