-- ***************************************************************** -- RDN-CABLE-SPECTRUM-GROUP-MIB.mib: -- Motorola BSR's Cable Spectrum Group MIB -- -- Copyright (C) 2001, 2008 by Motorola, Inc. -- All rights reserved. -- ***************************************************************** RDN-CABLE-SPECTRUM-GROUP-MIB DEFINITIONS ::= BEGIN IMPORTS rdnCableSpectrumObjects FROM RDN-CABLE-SPECTRUM-MIB MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-TYPE, Unsigned32, Counter32 FROM SNMPv2-SMI DisplayString, RowStatus, DateAndTime, TEXTUAL-CONVENTION, TruthValue, TestAndIncr, MacAddress FROM SNMPv2-TC IpAddress, Integer32 FROM SNMPv2-SMI InetAddressIPv4, InetAddressIPv6 FROM INET-ADDRESS-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB ifIndex, InterfaceIndex FROM IF-MIB TenthdB, docsIfUpChannelFrequency, docsIfUpChannelWidth, docsIfUpChannelModulationProfile FROM DOCS-IF-MIB rdnSlotNumber, rdnCardIfSlotNumber, rdnCardIfPortNumber FROM RDN-CHASSIS-MIB; rdnCableSpectrumGroup MODULE-IDENTITY LAST-UPDATED "201110100000Z" -- 10 Oct 2011 ORGANIZATION "Motorola" CONTACT-INFO "Motorola Customer Service 101 Tournament Drive Horsham, PA 19044 US Tel: +1 888 944 4357 Int Tel: +1 215 323 0044 Fax: +1 215 323 1502 Email: CPSSupport@Motorola.com" DESCRIPTION "This is the MIB Module for Cable Spectrum Group Management for MCNS compliant Cable Modem Termination Systems (CMTS). Copyright (C) 2001, 2008 by Motorola, Inc. All rights reserved." REVISION "201110100000Z" -- 10 Oct 2011 DESCRIPTION "Update rdnReferenceModemTable to support IPv6 Reference modems." REVISION "201109290000Z" -- 29 Sep 2011 DESCRIPTION "Update rdnReferenceModemTable to support IPv6 Reference modems." REVISION "201007240000Z" -- 24 Jul 2010 DESCRIPTION "rdnCableFftConfigAverage and rdnCableFftConfigIngressCanceller objects are added to rdnCableFftConfigObjects, These two objects are valid for DRX Only, Setting these values for CMTS 2x8 will not be having any impact." REVISION "201007240000Z" -- 24 Jul 2010 DESCRIPTION "For rdnReferenceModemTable and rdnModemExclusionTable, one of the table index values is changed from the rdnCardIfPortNumber to ifIndex. This change is to fetch all the instances of the MIB table, in case of DRX upstream channel assignment to the spectrum group is at RF channel level where as in case of cmts2x8 it is at port level. In case of DRX us port can have multiple RF channel so indexing with port will lead to missing some instance values." REVISION "201006110000Z" -- 11 Jun 2010 DESCRIPTION "The range of the upstream frequency on the RX48 Module is from 5 to 85 MHZ in Release 6.0 Changed the upper bound for rdnSpectrumHopBandHigh, rdnSpectrumHopBandLow, rdnSpectrumHopFrequency to 85000000 ." REVISION "201006070000Z" -- 07 June 2010 DESCRIPTION "Fixing rdnSpectrumGroupSnrHysteresisValue choices to match CLI (2,3). Also adding 'DRX' to comments concerning support on CMTS 2x8 cards" REVISION "201004210000Z" -- 21 Apr 2010 DESCRIPTION "Removing the LLC ping option from the SNR LOOP command because of buffer corruption." REVISION "200808080000Z" -- 08 August 2008 DESCRIPTION "Added MODULE Description back to this MIB. Cleaned up revision history formatting. Changed the range of rdnSpectrumGroupReferenceCMExclusion from 0..15 to 0..45. The default value for the same object was changed from 0 to 15." REVISION "200711290000Z" -- 29 Nov 2007 DESCRIPTION "Setting the equalization parameters for the SNR and SNR LOOP commands to be defaulted to the value of ON." REVISION "200609200000Z" -- 20 September 2006 DESCRIPTION "Adding support for the rdnModemExclusionGroup and and rdnReferenceModemGroup." REVISION "200607200000Z" -- 20 July 2006 DESCRIPTION "Adding a couple codes to rdnSpectrumGroupConflictType; updating codes for rdnCableAgilityHopAbortReason." REVISION "200509280000Z" -- 29 Sept 2005 DESCRIPTION "Adding Advanced Spectrum Management, SNR-based Frequency and Modulation Agility, with Rollback Feature to rdnSpectrumGroupTable. Also creating a new rdnSnrThresholdTable" REVISION "200508280000Z" -- 28 Aug 2005 DESCRIPTION "Adding rdnCableSnrLoopTestTable and rdnCableSnrLoopResultTable." REVISION "200410120000Z" -- 12 Oct 2004 DESCRIPTION "Minor clarification to range for rdnCableSnrLoopTestLoopCount (zero means 'unconfigured')" REVISION "200409160000Z" -- 16 Sept 2004 DESCRIPTION "Clarifying descriptive text for tables that currently apply only to port (physical channel) rather than to DOCSIS 2.0 logical channels" REVISION "200311120000Z" -- 11th November 2003 DESCRIPTION "Modified SYNTAX of rdnSpectrumMapIndex from INTEGER to Unsigned32." REVISION "200311050000Z" -- 05th November 2003 DESCRIPTION "Updated the CONTACT-INFO." REVISION "200309040000Z" -- 04th September 2003 DESCRIPTION "Modifies MAX-ACCESS for object rdnSpectrumGroupLoadBalance to be read-create instead of read-write." REVISION "200305230000Z" -- 23rd May 2003 DESCRIPTION "This adds comments and fix the SYNTAX clause for the following objects: rdnSpectrumHopFrequency, rdnSpectrumHopBandLow, rdnSpectrumHopBandHigh, rdnSpectrumHopPowerLevel, rdnSpectrumHopModulationProfile, and rdnSpectrumHopChannelWidth. Also changed the SYNTAX clause for the object rdnSpectrumDataSamples and the textual convention SpecDataArray used by the rdnSpectrumDataArray object." REVISION "200304290000Z" -- 29th April 2003 DESCRIPTION "This `corrects past mistakes' where ASN.1 allowed hyphens but SMIv2 states that hyphens are not allowed in identifiers for objects or for labels on enumerated integer values. Hyphens where removed from the labels on enumerated integer values from the textual convention 'SpectrumHopChannelWidth' and from the 'rdnSpectrumHopChannelWidth' object." ::= { rdnCableSpectrumObjects 2 } rdnCableFftGroup OBJECT IDENTIFIER ::= { rdnCableSpectrumGroup 9 } -- Textual Conventions SchedulingWeekDay ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The scheduling week day." SYNTAX INTEGER { sunday (1), monday (2), tuesday (3), wednesday (4), thursday (5), friday (6), saturday (7), everyday (8) } SpectrumHopSelections ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The rules for spectrum hop." SYNTAX INTEGER { frequency (1), band (2), powerDefault (3), powerLevel (4), modulationProfile (5), channelWidth (6) } SpecDataArray ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An array holds the spectrum data." SYNTAX OCTET STRING (SIZE (2..600)) ThousandthdB ::= TEXTUAL-CONVENTION DISPLAY-HINT "d-4" STATUS current DESCRIPTION "This data type represents power levels that are normally expressed in dB. Units are in thousandths of a dB; for example, 5.1234 dB will be represented as 51234." SYNTAX Integer32 -- -- Spectrum Group -- -- Spectrum manager can configure and activate frequency agility by using -- the spectrum groups. Up to 256 spectrum groups can be created for -- each CMTS system. Each spectrum group supports up to 256 shared upstream -- channels. -- Spectrum data converts frequency range of 5 to 65 MHz to support -- Euro-DOCSIS -- rdnSpectrumGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnSpectrumGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table keeps the records of spectrum groups. These groups can be configured and activated by the spectrum manager and used by the CMTS upstream port for frequency hopping. In this table, certain objects will apply DRX and CMTS 2x8 cards, and others will apply to CMTS 1x8 and 1x4 cards, as indicated in the individual DESCRIPTION statements. For DRX and CMTS 2x8 cards, all member channels of the same spectrum group must reside on the same, physical 2x8 card in the chassis. As the normal practice, it is recommended that all receivers on the same CMTS card should be physically cabled together. At a minimum, all receivers in spectrum group should be cabled together. If receivers are in different spectrum groups, it is expected that they can independently reuse the same spectrum, so must *not* be physically cabled together. For CMTS 1x8 and 1x4 cards, it is not forbidden to add receivers from different cards to the same spectrum group, but this is not recommended. " ::= { rdnCableSpectrumGroup 1 } rdnSpectrumGroupEntry OBJECT-TYPE SYNTAX RdnSpectrumGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of attributes for an entry in the rdnSpectrumGroupEntry. An entry in this table exists for each spectrum group that has been configured by the spectrum manager." INDEX { rdnSpectrumGroupName } ::= { rdnSpectrumGroupTable 1 } RdnSpectrumGroupEntry ::= SEQUENCE { rdnSpectrumGroupName DisplayString, rdnSpectrumGroupId Unsigned32, rdnSpectrumGroupHopPeriod Unsigned32, rdnSpectrumGroupHopThresholdFlap Unsigned32, rdnSpectrumGroupHopThresholdError Unsigned32, rdnSpectrumGroupHopRollbackEnable INTEGER, rdnSpectrumDataCollectResolution Unsigned32, rdnSpectrumDataCollectInterval Unsigned32, rdnSpectrumGroupGuardBand Unsigned32, rdnSpectrumGroupRowStatus RowStatus, rdnSpectrumOfflineModemCount Integer32, rdnSpectrumOnlineModemCount Integer32, rdnSpectrumActiveModemCount Integer32, rdnSpectrumRegisteredModemCount Integer32, rdnSpectrumProvisionedModemCount Integer32, rdnSpectrumUnregisteredModemCount Integer32, rdnSpectrumGroupUnerroreds Counter32, rdnSpectrumGroupCorrecteds Counter32, rdnSpectrumGroupUncorrectables Counter32, rdnSpectrumGroupStaticLoadBalEnable INTEGER, rdnSpectrumGroupLoadBalance TruthValue, rdnSpectrumGroupActiveChannelSamplingPeriod Unsigned32, rdnSpectrumGroupHopRollbackChannelSamplingPeriod Unsigned32, rdnSpectrumGroupHopSpareChannelSamplingPeriod Unsigned32, rdnSpectrumGroupSnrHysteresisValue Unsigned32, rdnSpectrumGroupReferenceCMExclusion Unsigned32 } rdnSpectrumGroupName OBJECT-TYPE SYNTAX DisplayString ( SIZE (1..20) ) MAX-ACCESS read-only STATUS current DESCRIPTION "The text name (index) of the spectrum group." ::= { rdnSpectrumGroupEntry 1 } rdnSpectrumGroupId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number index for the spectrum group." ::= { rdnSpectrumGroupEntry 2 } rdnSpectrumGroupHopPeriod OBJECT-TYPE SYNTAX Unsigned32 (30..3600) MAX-ACCESS read-create STATUS current DESCRIPTION "The rate at which the frequency hop takes place. This would be useful in preventing excessive hops. Unit is in second. This parameter applies only to CMTS 1x8 and 1x4 cards. " DEFVAL { 300 } ::= { rdnSpectrumGroupEntry 3 } rdnSpectrumGroupHopThresholdFlap OBJECT-TYPE SYNTAX Unsigned32 (0..100) MAX-ACCESS read-create STATUS current DESCRIPTION "The CM flap rate percentage threshold that controls the hopping frequency. The hopping only happens when the percentage of flap CMs is higher than this threshold. Value 0 means the flap threshold hop disabled. This parameter applies to CMTS 1x8 and 1x4 cards. " DEFVAL { 0 } ::= { rdnSpectrumGroupEntry 4 } rdnSpectrumGroupHopThresholdError OBJECT-TYPE SYNTAX Unsigned32 (1..1000) MAX-ACCESS read-create STATUS current DESCRIPTION "The FEC error rate percentage threshold that controls the hopping frequency. The hopping only happens when the error rate percentage is higher than this threshold. The unit is 1/1000. This parameter applies to CMTS 1x8 and 1x4 cards. " DEFVAL { 10 } ::= { rdnSpectrumGroupEntry 5 } rdnSpectrumGroupHopRollbackEnable OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This field controls the spectrum rollback option when the original channel quality recovers. The rollback is allowed when this field is enabled. The rollback is not allowed when this field is set to disable. This parameter applies to all CMTS card types. " DEFVAL { 2 } ::= { rdnSpectrumGroupEntry 6 } rdnSpectrumDataCollectResolution OBJECT-TYPE SYNTAX Unsigned32 (200000..400000) MAX-ACCESS read-create STATUS current DESCRIPTION "The spectrum data collection resolution, in Hz. This parameter applies to all CMTS card types. " DEFVAL { 200000 } ::= { rdnSpectrumGroupEntry 7 } rdnSpectrumDataCollectInterval OBJECT-TYPE SYNTAX Unsigned32 (0 | 60..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The spectrum data collection interval, in second. Minimum value 60 seconds. Value 0 means the collection is disabled. This parameter applies to all CMTS card types. " DEFVAL { 0 } ::= { rdnSpectrumGroupEntry 8 } rdnSpectrumGroupGuardBand OBJECT-TYPE SYNTAX Unsigned32 (0..60000000) MAX-ACCESS read-create STATUS current DESCRIPTION "The minimum spectrum separation between upstream channels in the same spectrum group, in Hz. This parameter applies to CMTS 1x8 and 1x4 cards. " DEFVAL { 0 } ::= { rdnSpectrumGroupEntry 9 } rdnSpectrumGroupRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Controls and reflects the status of rows in this table. This field is used to control the addition and deletion of a spectrum group." ::= { rdnSpectrumGroupEntry 10 } rdnSpectrumOfflineModemCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of offline modems for this spectrum group" ::= { rdnSpectrumGroupEntry 11 } rdnSpectrumOnlineModemCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of online modems for this spectrum group" ::= { rdnSpectrumGroupEntry 12 } rdnSpectrumActiveModemCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of active modems for this spectrum group" ::= { rdnSpectrumGroupEntry 13 } rdnSpectrumRegisteredModemCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of registered modems for this spectrum group" ::= { rdnSpectrumGroupEntry 14 } rdnSpectrumProvisionedModemCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of provisioned modems for this spectrum group" ::= { rdnSpectrumGroupEntry 15 } rdnSpectrumUnregisteredModemCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Unregistered modems for this spectrum group" ::= { rdnSpectrumGroupEntry 16 } rdnSpectrumGroupUnerroreds OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Codewords received on this spectrum group without error. This includes all codewords, whether or not they were part of frames destined for this device." ::= { rdnSpectrumGroupEntry 17 } rdnSpectrumGroupCorrecteds OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Codewords received on this spectrum group with correctable errors. This includes all codewords, whether or not they were part of frames destined for this device." ::= { rdnSpectrumGroupEntry 18 } rdnSpectrumGroupUncorrectables OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Codewords received on this spectrum group with uncorrectable errors. This includes all codewords, whether or not they were part of frames destined for this device." ::= { rdnSpectrumGroupEntry 19 } rdnSpectrumGroupStaticLoadBalEnable OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This field controls the Static Load Balancing feature. This parameter applies to all CMTS card types. " DEFVAL { 2 } ::= { rdnSpectrumGroupEntry 20 } rdnSpectrumGroupLoadBalance OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this object to TRUE performs a Static Load Balancing for the spectrum group. Reading this object always returns FALSE." ::= { rdnSpectrumGroupEntry 21 } rdnSpectrumGroupActiveChannelSamplingPeriod OBJECT-TYPE SYNTAX Unsigned32 (0 | 1..15) MAX-ACCESS read-create STATUS current DESCRIPTION "The signal quality of the active channel is periodically measured for SNR. This object is the time between two consecutive signal quality measurements of the active channel. A value of zero means that the timer is disabled. This object applies to DRX and CMTS 2x8. Units are in seconds." DEFVAL { 3 } ::= { rdnSpectrumGroupEntry 22 } rdnSpectrumGroupHopRollbackChannelSamplingPeriod OBJECT-TYPE SYNTAX Unsigned32 (10..300) MAX-ACCESS read-create STATUS current DESCRIPTION "When a primary channel is swapped with the spare channel, if the rollback is configured, the primary channel is periodically measured for signal quality in the background using the 9th receiver. This object is the time between two consecutive signal quality measurements of the primary channel. This object applies to DRX and CMTS 2x8. Units are in seconds." DEFVAL { 60 } ::= { rdnSpectrumGroupEntry 23 } rdnSpectrumGroupHopSpareChannelSamplingPeriod OBJECT-TYPE SYNTAX Unsigned32 (10..600) MAX-ACCESS read-create STATUS current DESCRIPTION "If a primary channel could not be swapped for noise avoidance with a spare channel, due to poor signal quality of the spare channels, the spare channels are periodically assessed on the 9th receiver. This object is the time between two consecutive signal quality measurements of all the spare channels. In each spare channel quality sampling cycle, all the spare channels are tested (this is not the delay between testing two spare channels. This object applies to DRX and CMTS 2x8. Units are in seconds." DEFVAL { 10 } ::= { rdnSpectrumGroupEntry 24 } rdnSpectrumGroupSnrHysteresisValue OBJECT-TYPE SYNTAX Unsigned32 ( 2 | 3) MAX-ACCESS read-create STATUS current DESCRIPTION "SNR hysteresis (a default hysteresis of 2dB) is used to determine the SNR threshold for the downward transition from upper modulation type to a lower modulation type. The hysteresis can be configured to a resolution of 1dB. The operator must be aware of the effects of lowering or increasing the hysteresis. An increase in hysteresis will delay the channel switching. A decrease in hysteresis could result in too many transitions. For example, if the SNR threshold is configured to 20dB and the default SNR hysteresis of 2dB is used, then in the event of noise, a channel switch from primary to spare will take effect when the SNR value drops to 18dB on the primary channel (provided the spare channel's SNR is at least 20dB). When the primary channel's SNR goes up to 20dB, the primary channel will be rolled back. If a spare channel is not available or the spare channel's SNR is below 20dB, and if a secondary modulation profile is configured, then the modulation profile of the primary channel is changed. This object applies to DRX and CMTS 2x8. Allowable choies are 2dB or 3dB" DEFVAL { 2 } ::= { rdnSpectrumGroupEntry 25 } rdnSpectrumGroupReferenceCMExclusion OBJECT-TYPE SYNTAX Unsigned32 (0..45) MAX-ACCESS read-create STATUS current DESCRIPTION "This parameter defines the number of low SNR modem(s), on each upstream in the spectrum-group, not allowed to be used for channel assessment. This parameter has no effect when the number of registered modems on a specific upstream is less than double the configured value." DEFVAL { 15 } ::= { rdnSpectrumGroupEntry 26 } -- Band schedule table defines the spectrum band schedules for the specific -- spectrum group rdnSpectrumBandSchedTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnSpectrumBandSchedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table keeps the records of spectrum band scheduled for a specific spectrum group. This table applies to CMTS 1x8 and 1x4, only. " ::= { rdnCableSpectrumGroup 2 } rdnSpectrumBandSchedEntry OBJECT-TYPE SYNTAX RdnSpectrumBandSchedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of attributes for an entry in the rdnSpectrumBandScheEntry." INDEX { rdnSpectrumGroupId, rdnSpectrumBandSchedId, rdnSpectrumBandSchedAction } ::= { rdnSpectrumBandSchedTable 1 } RdnSpectrumBandSchedEntry ::= SEQUENCE { rdnSpectrumBandSchedId Unsigned32, rdnSpectrumBandSchedAction Unsigned32, rdnSpectrumBandFreqLow Unsigned32, rdnSpectrumBandFreqHigh Unsigned32, rdnSpectrumBandSchedWeekDay SchedulingWeekDay, rdnSpectrumBandSchedHour Unsigned32, rdnSpectrumBandSchedMinute Unsigned32, rdnSpectrumBandSchedSecond Unsigned32, rdnSpectrumBandSchedRowStatus RowStatus } rdnSpectrumBandSchedId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The identifier for the band schedule, it is the second index for the spectrum band schedule table." ::= { rdnSpectrumBandSchedEntry 1 } rdnSpectrumBandSchedAction OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The action on the specified frequency band. The third index of this band schedule table. Band add (1), band delete (2)." ::= { rdnSpectrumBandSchedEntry 2 } rdnSpectrumBandFreqLow OBJECT-TYPE SYNTAX Unsigned32 (5000000..65000000) MAX-ACCESS read-create STATUS current DESCRIPTION "The spectrum band low frequency in Hz. The lower limit is 5 MHz for North American standard, is 5 MHz for European standard. " DEFVAL { 5000000 } ::= { rdnSpectrumBandSchedEntry 3 } rdnSpectrumBandFreqHigh OBJECT-TYPE SYNTAX Unsigned32 (5000000..65000000) MAX-ACCESS read-create STATUS current DESCRIPTION "The spectrum band high frequency in Hz. This value must be at least 200000 Hz higher than the band low frequency. The upper limit is 42 MHz for North American standard, is 65 MHz for European standard. " DEFVAL { 42000000 } ::= { rdnSpectrumBandSchedEntry 4 } rdnSpectrumBandSchedWeekDay OBJECT-TYPE SYNTAX SchedulingWeekDay MAX-ACCESS read-create STATUS current DESCRIPTION "The week day of the band schedule." DEFVAL { everyday } ::= { rdnSpectrumBandSchedEntry 5 } rdnSpectrumBandSchedHour OBJECT-TYPE SYNTAX Unsigned32 (0..23) MAX-ACCESS read-create STATUS current DESCRIPTION "The hour of the band schedule (in 24-hour format)." DEFVAL { 0 } ::= { rdnSpectrumBandSchedEntry 6 } rdnSpectrumBandSchedMinute OBJECT-TYPE SYNTAX Unsigned32 (0..59) MAX-ACCESS read-create STATUS current DESCRIPTION "The minute of the band schedule." DEFVAL { 0 } ::= { rdnSpectrumBandSchedEntry 7 } rdnSpectrumBandSchedSecond OBJECT-TYPE SYNTAX Unsigned32 (0..59) MAX-ACCESS read-create STATUS current DESCRIPTION "The second of the band schedule." DEFVAL { 0 } ::= { rdnSpectrumBandSchedEntry 8 } rdnSpectrumBandSchedRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status that controls the addition and deletion of the band schedule entry." ::= { rdnSpectrumBandSchedEntry 9 } -- Spectrum hop rule table defines the hopping rules rdnSpectrumHopTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnSpectrumHopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table keeps the records of spectrum hopping rules for a specific spectrum group. Certain objects in this table apply to all CMTS card types, while others might apply to DRX and CMTS 2x8, or only to CMTS 1x8 and 1x4, as indicated by the individual DESCRIPTION statements. " ::= { rdnCableSpectrumGroup 3 } rdnSpectrumHopEntry OBJECT-TYPE SYNTAX RdnSpectrumHopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of attributes for an entry in the rdnSpectrumHopTable. This table is index by a rdnSpectrumGroupId and a rdnSpectrumHopId. Each row within this table reflects one Hop action for a spectrum group. The rdnSelection object reflects which Hop Action this row describes. For the rest of the objects within this row that do not apply to this Hop action a value of 0 will be returned. Only the object(s) that for which is object action applies will report a valid value." INDEX { rdnSpectrumGroupId, rdnSpectrumHopId } ::= { rdnSpectrumHopTable 1 } RdnSpectrumHopEntry ::= SEQUENCE { rdnSpectrumHopId Unsigned32, rdnSpectrumHopSelection SpectrumHopSelections, rdnSpectrumHopPriority INTEGER, rdnSpectrumHopFrequency Unsigned32, rdnSpectrumHopBandLow Unsigned32, rdnSpectrumHopBandHigh Unsigned32, rdnSpectrumHopPowerLevel INTEGER, rdnSpectrumHopModulationProfile INTEGER, rdnSpectrumHopChannelWidth INTEGER, rdnSpectrumHopRowStatus RowStatus } rdnSpectrumHopId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index for the spectrum hop rule table." ::= { rdnSpectrumHopEntry 1 } rdnSpectrumHopSelection OBJECT-TYPE SYNTAX SpectrumHopSelections MAX-ACCESS read-create STATUS current DESCRIPTION "Identifies the selection of the action for this spectrum hop rule. If the value is 'frequency(1)' then the only applicable objects are rdnSpectrumHopPriority and rdnSpectrumHopFrequency. If the value is 'band(2)' then the only applicable objects are rdnSpectrumHopPriority, rdnSpectrumHopBandLow, and rdnSpectrumHopBandHigh. If the value is 'powerDefault(3)' then the only applicable objects are rdnSpectrumHopPriority and rdnSpectrumHopPowerLevel. If the value is 'modulationProfile(5)' then the only applicable objects are rdnSpectrumHopPriority and rdnSpectrumHopModulationProfile. If the value is 'channelWidth(6)' then the only applicable object for this row is rdnSpectrumHopPriority and rdnSpectrumHopChannelWidth. The powerDefault(3), powerLevel (4), and channelWidth (6) selections apply only to CMTS 1x4 and 1x8 cards, but not to CMTS 2x8 cards.. All other selections apply to all CMTS card types" DEFVAL { frequency } ::= { rdnSpectrumHopEntry 2 } rdnSpectrumHopPriority OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-create STATUS current DESCRIPTION "Identifies the priority for this spectrum hop policy. The default value is 128. The range is 1 to 255. This parameter applies to all CMTS card types. " DEFVAL { 128 } ::= { rdnSpectrumHopEntry 3 } rdnSpectrumHopFrequency OBJECT-TYPE SYNTAX Unsigned32 ( 0 | 5000000..85000000 ) MAX-ACCESS read-create STATUS current DESCRIPTION "Identifies the center frequency for the spectrum hop schedule entry. The hop can be specified with a discrete center frequency or with a band but not both in the same group. This object is not applicable to a hop action when a value of 0 is reported by this object. This parameter applies to all CMTS card types, although the criteria for making a hop decision depend on card type. For CMTS 2x8 cards, hop decisions are made on the basis of SNR measurements. For older, 1x8 and 1x4 cards, hop decisions are made on the basis of error thresholds, or modem flapping. " DEFVAL { 10000000 } ::= { rdnSpectrumHopEntry 4 } rdnSpectrumHopBandLow OBJECT-TYPE SYNTAX Unsigned32 ( 0 | 5000000..85000000 ) MAX-ACCESS read-create STATUS current DESCRIPTION "The start frequency for the individual spectrum hop. This object is not applicable to a hop action when a value of 0 is reported by this object. This parameter applies to all CMTS card types. " DEFVAL { 8400000 } ::= { rdnSpectrumHopEntry 5 } rdnSpectrumHopBandHigh OBJECT-TYPE SYNTAX Unsigned32 ( 0 | 5000000..85000000 ) MAX-ACCESS read-create STATUS current DESCRIPTION "The stop frequency for the individual spectrum hop. This value must be at least 200000 Hz higher than the start frequency. This object is not applicable to a hop action when a value of 0 is reported by this object. This parameter applies to all CMTS card types. " DEFVAL { 42000000 } ::= { rdnSpectrumHopEntry 6 } rdnSpectrumHopChannelWidth OBJECT-TYPE SYNTAX INTEGER { notApplicable(0), channelWidth1(200000), channelWidth2(400000), channelWidth3(800000), channelWidth4(1600000), channelWidth5(3200000) } MAX-ACCESS read-create STATUS current DESCRIPTION "Identifies the channel width change for this individual spectrum hop. The valid band width is 200000 Hz, 400000 Hz, 800000 Hz, 1600000 Hz, 3200000 Hz. This object is not applicable to a hop action when a value of 0 is reported by this object. This object applies only to CMTS 1x4 and 1x8 cards, not to CMTS 2x8 cards." DEFVAL { 3200000 } ::= { rdnSpectrumHopEntry 7 } rdnSpectrumHopPowerLevel OBJECT-TYPE SYNTAX INTEGER ( -160..260 ) MAX-ACCESS read-create STATUS current DESCRIPTION "Identifies a power level change for this individual spectrum hop. Different channel width has different power level range, < -160, 140 > for 200 KHz, < -130, 170 > for 400 KHz, < -100, 200 > for 800 KHz, < -70, 230 > for 1600 KHz, < -40, 260 > for 3200 KHz. For power default, the range is < -150, 150 > for all the channel widths. The unit is in tenths of a dBmV. If the rdnSpectrumHopSelection is 'powerDefault(3)' and a value of 0 is returned for this object for the same instance then this is a valid Power Level for this Hop action. Else if the rdnSpectrumHopSelection is not 'powerDefault(3)' and a value of 0 is returned for this object for the same instance then this object is not applicable to this hop action. This object applies only to CMTS 1x4 and 1x8 cards, not to CMTS 2x8 cards." DEFVAL { 0 } ::= { rdnSpectrumHopEntry 8 } rdnSpectrumHopModulationProfile OBJECT-TYPE SYNTAX INTEGER ( 0 | 1..16 ) MAX-ACCESS read-create STATUS current DESCRIPTION "Identifies the modulation profile change for this individual spectrum hop. This object is not applicable to a hop action when a value of 0 is reported by this object. This parameter applies to all CMTS card types, although the criteria for making hop decisions is dependent on card type. For CMTS 2x8 cards, hop decisions are made on the basis of SNR measurements. For older, 1x8 and 1x4 cards, hop decisions are made on the basis of error thresholds, or modem flapping. " DEFVAL { 1 } ::= { rdnSpectrumHopEntry 9 } rdnSpectrumHopRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status that controls the add and deletion of the spectrum hop rule entry." ::= { rdnSpectrumHopEntry 10 } -- member channel table defines the association of the upstream ports and -- the spectrum groups, it also controls the spectrum hopping (enable or -- disable) for this upstream channel. rdnSpectrumMemberChannelTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnSpectrumMemberChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table keeps the records of the associations between upstream ports and spectrum groups. For CMTS 2x8 cards, all members of the same spectrum group must reside on the same physical card. Channels on CMTS 1x8 and 1x4 cards can be mixed in the same spectrum group, but they may NOT be mixed in the same spectrum group with CMTS 2x8 channels. As the normal practice, it is recommended that all receivers on the same CMTS card should be physically cabled together. At a minimum, all receivers in spectrum group should be cabled together. If channels are in different spectrum groups, it is expected that they can independently reuse the same spectrum, so must *not* be physically cabled together. For CMTS 1x8 and 1x4 cards, it is not forbidden to add receivers from different cards to the same spectrum group, but this is not recommended. " ::= { rdnCableSpectrumGroup 4 } rdnSpectrumMemberChannelEntry OBJECT-TYPE SYNTAX RdnSpectrumMemberChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of attributes for an entry in the RdnSpectrumMemberChannelEntry. It is indexed by ifIndex values that are associated with upstream ports (ifType = 129)" INDEX { ifIndex } ::= { rdnSpectrumMemberChannelTable 1 } RdnSpectrumMemberChannelEntry ::= SEQUENCE { rdnUsChannelId INTEGER, rdnMemChSpectrumGroupId Unsigned32, rdnMemChSpectrumGroupName DisplayString } rdnUsChannelId OBJECT-TYPE SYNTAX INTEGER (1..255) -- upper 4 bits for slot ID, lower 4 bits for US MAX-ACCESS read-only STATUS current DESCRIPTION "The upstream channel ID." ::= { rdnSpectrumMemberChannelEntry 1 } rdnMemChSpectrumGroupId OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The ID for the spectrum group that is associated with this upstream port. Value 0 means no association." ::= { rdnSpectrumMemberChannelEntry 2 } rdnMemChSpectrumGroupName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The text name of the associated spectrum group." ::= { rdnSpectrumMemberChannelEntry 3 } -- Spectrum data table stores the spectrum data collection information rdnSpectrumDataTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnSpectrumDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table stores the noise and error rate for the different frequency bands. This table applies to all CMTS card types." ::= { rdnCableSpectrumGroup 5 } rdnSpectrumDataEntry OBJECT-TYPE SYNTAX RdnSpectrumDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of attributes for an entry in the rdnSpectrumDataEntry. The index for this table is an ifIndex that is associated with an upstream port (ifType = 129)" INDEX { ifIndex } ::= { rdnSpectrumDataTable 1 } RdnSpectrumDataEntry ::= SEQUENCE { rdnSpectrumDataIndex INTEGER, rdnSpecDataUsChannelId INTEGER, rdnSpectrumDataStartFrequency Unsigned32, rdnSpectrumDataResolution INTEGER, rdnSpectrumDataSamples INTEGER, rdnSpectrumDataLastUpdate DateAndTime, rdnSpectrumDataArray SpecDataArray } rdnSpectrumDataIndex OBJECT-TYPE SYNTAX INTEGER (1..200) MAX-ACCESS read-only STATUS current DESCRIPTION " The internal index of the spectrum data" ::= { rdnSpectrumDataEntry 1 } rdnSpecDataUsChannelId OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The upstream channel ID." ::= { rdnSpectrumDataEntry 2 } rdnSpectrumDataStartFrequency OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Start Frequency of the spectrum data collection" ::= { rdnSpectrumDataEntry 3 } rdnSpectrumDataResolution OBJECT-TYPE SYNTAX INTEGER (200000..32000000) MAX-ACCESS read-only STATUS current DESCRIPTION "Resolution of the spectrum data collection in Hz" ::= { rdnSpectrumDataEntry 4 } rdnSpectrumDataSamples OBJECT-TYPE SYNTAX INTEGER (1..300) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of data samples used in this spectrum data collection period" ::= { rdnSpectrumDataEntry 5 } rdnSpectrumDataLastUpdate OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "Date and time when this collection data was last updated " ::= { rdnSpectrumDataEntry 6 } rdnSpectrumDataArray OBJECT-TYPE SYNTAX SpecDataArray MAX-ACCESS read-only STATUS current DESCRIPTION "The data array that holds the spectrum data." ::= { rdnSpectrumDataEntry 7 } -- Spectrum quality table stores the spectrum quality information rdnSpectrumQualityTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnSpectrumQualityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table stores the spectrum quality information. This table applies to all CMTS card types. " ::= { rdnCableSpectrumGroup 6} rdnSpectrumQualityEntry OBJECT-TYPE SYNTAX RdnSpectrumQualityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of attributes for an entry in the rdnSpectrumDataEntry." INDEX { ifIndex } ::= { rdnSpectrumQualityTable 1 } RdnSpectrumQualityEntry ::= SEQUENCE { rdnSpecQualityUsChId INTEGER, rdnSpectrumQualityDataLastUpdate DateAndTime, rdnSpectrumDataInBandPower INTEGER, rdnSpectrumTotCodeWord Unsigned32, rdnSpectrumErrorCodeWord Unsigned32 } rdnSpecQualityUsChId OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Identifies the upstream channel id for which the spectrum signal quality is gathered. " ::= { rdnSpectrumQualityEntry 1 } rdnSpectrumQualityDataLastUpdate OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "Date and time when this data was last updated " ::= { rdnSpectrumQualityEntry 2 } rdnSpectrumDataInBandPower OBJECT-TYPE SYNTAX INTEGER (-600..363) MAX-ACCESS read-only STATUS current DESCRIPTION "The in-band power for this frequency band. The unit is the tenths of dBmV." ::= { rdnSpectrumQualityEntry 3 } rdnSpectrumTotCodeWord OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of code words transfer through this interface" ::= { rdnSpectrumQualityEntry 4 } rdnSpectrumErrorCodeWord OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The uncorrectable error code words received through this interface." ::= { rdnSpectrumQualityEntry 5 } -- Spectrum map table keeps the spectrum map rdnSpectrumMapTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnSpectrumMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table keeps the records of spectrum usage. This table applies to all CMTS card types. " ::= { rdnCableSpectrumGroup 7} rdnSpectrumMapEntry OBJECT-TYPE SYNTAX RdnSpectrumMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of attributes for an entry in the rdnSpectrumMapEntry." INDEX { rdnSpectrumGroupId, rdnSpectrumMapIndex } ::= { rdnSpectrumMapTable 1 } RdnSpectrumMapEntry ::= SEQUENCE { rdnSpectrumMapIndex Unsigned32, rdnSpectrumMapStartFrequency Unsigned32, rdnSpectrumMapStopFrequency Unsigned32, rdnSpectrumMapStatus INTEGER } rdnSpectrumMapIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION " Identifies an entry in the spectrum map table" ::= { rdnSpectrumMapEntry 1 } rdnSpectrumMapStartFrequency OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The start frequency of the current spectrum band." ::= { rdnSpectrumMapEntry 2 } rdnSpectrumMapStopFrequency OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The stop frequency of the current spectrum band." ::= { rdnSpectrumMapEntry 3 } rdnSpectrumMapStatus OBJECT-TYPE SYNTAX INTEGER { invalid(0), available(1), occupied(2), adminDown(3), scheduled(4), reserved(5), agile(6), hopAvailable(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The spectrum band status: invalid(0) - is not used, and would indicate a software error. available(1) - spectrum that is available for use in an RSSI-based spectrum group. occupied(2) - configured frequency, assigned to a member channel. The upstream might be in either shut or no shut state. adminDown(3) - spectrum this administratively down as a result of the 'schedule' feature for RSSI-based spectrum groups. scheduled(4) - spectrum is scheduled for RSSI-based spectrum group, via the 'schedule' feature. reserved(5) - configured frequency, for an upstream that has hopped to another frequency. agile(6) - upstream has hopped to this frequency hopAvailable(7) - is spectrum that is available for use as a hopping action in an SNR-based spectrum group." ::= { rdnSpectrumMapEntry 4 } -- -- FFT Group -- -- The following objects are used for configuration -- and activation of FFT measurements. -- -- The results will only be available after the measurement -- is initiated. If the configuration is modified the results -- will become unavailable. This guarantees that when the -- results are present, they are consistent with the -- configuration. rdnCableFftConfigObjects OBJECT IDENTIFIER ::= { rdnCableFftGroup 1 } rdnCableFftConfigIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-write STATUS current DESCRIPTION "A value that uniquely identifies an interface with an ifType of docsCableUpstream(129) in the ifTable. The interface identified by a particular value of this object is the same interface identified by the same value of ifIndex. Setting this object sets up the interface that will be addressed by any subsequent sets to rdnCableFftConfigSpinLock, rdnCableFftConfigSamples, rdnCableFftConfigOpMode, and rdnCableFftConfigWindow. These objects apply to CMTS 2x8 cards, and to BSR2000. " REFERENCE "RFC 2233, ifIndex" ::= { rdnCableFftConfigObjects 1 } rdnCableFftConfigSpinLock OBJECT-TYPE SYNTAX TestAndIncr MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to initiate FFT measurement, and identify the current invocation an FFT measurement, for interface that is currently selected by rdnCableFftConfigIfIndex. This object is applicable to CMTS 2x8 cards, and to BSR2000. It is recommended that a management application will first read this object, then perform a set to the current value. This set may occur in the same set request as other sets. It is recommended that a management application will first read this object, then perform a set to the current value. This set may occur in the same set request as other sets. This object should be read again, and should return the previous value + 1, indicating the results are valid and the configuration has not changed. Else, another management station has initiated another measurement (following this procedure). 1. Get this object and store in configNum 2. Set any desired configuration objects 3. Set this object to configNum (Note: 2 & 3 can be done in the same set request) 4. If step 3 fails, then another management station has already set this object. 5. After short delay, get requested data from rdnCableFftResultTable. 6. Get this object and compare with configNum + 1 7. If step 6 yields the same value, the data retrieved in step 5 is valid. The use of rdnCableFftConfigSpinLock is to avoid conflicts with another SNMP command responder application which may also be acting on the rdnCableFftConfigObjects. Setting this object does not provide exclusive access. Other managers will still be able to modify these objects." REFERENCE "RFC 2579, TestAndIncr" ::= { rdnCableFftConfigObjects 2 } rdnCableFftConfigLastTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The date and time of the last FFT measurement." REFERENCE "RFC 2579, DateAndTime" ::= { rdnCableFftConfigObjects 3 } rdnCableFftConfigSamples OBJECT-TYPE SYNTAX INTEGER { samples256 ( 256), samples512 ( 512), samples1024 (1024), samples2048 (2048), samples4096 (4096) } MAX-ACCESS read-write STATUS current DESCRIPTION "The number of samples used for the FFT measurement. samples4096 is applicable only for DRX." ::= { rdnCableFftConfigObjects 4 } rdnCableFftConfigOpMode OBJECT-TYPE SYNTAX INTEGER { tapIn(1), idle-sid(2), hardware(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set to tapIn(1) to utilize the FFT engine on the extra demodulator, which has its own RF path. tapIn(1) is valid for cmts 2x8 idle-sid(2) and hardware(3) are valid for DRX." ::= { rdnCableFftConfigObjects 5 } rdnCableFftConfigWindow OBJECT-TYPE SYNTAX INTEGER { rectangular(1), hanning(2), hamming(3), blackman(4), blackman-harris(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "The windowing function that is used for this measurement." ::= { rdnCableFftConfigObjects 6 } rdnCableFftConfigAverage OBJECT-TYPE SYNTAX INTEGER { avg1(1), avg2(2), avg4(4), avg8(8), avg16(16), avg32(32), avg64(64), avg128(128) } MAX-ACCESS read-write STATUS current DESCRIPTION "Average that is used for FFT measurement Applicable only for DRX. Setting This Object's value is not allowed for cmts2x8." ::= { rdnCableFftConfigObjects 7 } rdnCableFftConfigIngressCanceller OBJECT-TYPE SYNTAX INTEGER { pre(1), post(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "ingress-canceller-option that is used for FFT measurement Applicable only for DRX. Setting This Object's value is not allowed for cmts2x8." ::= { rdnCableFftConfigObjects 8 } -- -- rdnCableFftResultTable -- rdnCableFftResultTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnCableFftResultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the statistical data collected as a result of a FFT measurement, initiated by setting rdnCableFftConfigSpinLock. This table applies to CMTS 2x8 cards, and to BSR2000. " ::= { rdnCableFftGroup 2 } rdnCableFftResultEntry OBJECT-TYPE SYNTAX RdnCableFftResultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of results from a FFT measurement." INDEX { rdnCableFftResultSampleFreq } ::= { rdnCableFftResultTable 1 } RdnCableFftResultEntry ::= SEQUENCE { rdnCableFftResultSampleFreq Integer32, rdnCableFftResultPowerValue ThousandthdB } rdnCableFftResultSampleFreq OBJECT-TYPE SYNTAX Integer32 UNITS "hertz" MAX-ACCESS not-accessible STATUS current DESCRIPTION "Sample frequency used for the indicated power value." ::= { rdnCableFftResultEntry 1 } rdnCableFftResultPowerValue OBJECT-TYPE SYNTAX ThousandthdB UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "FFT power value for this sample frequency." ::= { rdnCableFftResultEntry 2 } -- -- rdnCableSnrGroup keeps configuration parameter and test result for SNR -- measurement on 9th receiver feature. rdnCableSpectrumGroup 8 is saved for -- FFT feature. -- rdnCableSnrGroup OBJECT IDENTIFIER ::= { rdnCableSpectrumGroup 10 } rdnCableSnrConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnCableSnrConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table allows configuration for SNR tests. These tests are performed on the ninth receiver for diagnostic purposes. This table applies to CMTS 2x8 cards, and to BSR2000. " ::= { rdnCableSnrGroup 1 } rdnCableSnrConfigEntry OBJECT-TYPE SYNTAX RdnCableSnrConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of attributes for an entry in the rdnCableSnrConfigEntry. An entry in this table exists for each slot/port of 2x8 CMTS." INDEX { ifIndex } ::= {rdnCableSnrConfigTable 1} RdnCableSnrConfigEntry ::= SEQUENCE { rdnCableSnrConfigIdleSpectrumStart Integer32, rdnCableSnrConfigIdleSpectrumStop Integer32, rdnCableSnrConfigChannelWidth INTEGER, rdnCableSnrConfigEqualization INTEGER } rdnCableSnrConfigIdleSpectrumStart OBJECT-TYPE SYNTAX Integer32 ( 0|5000000..65000000 ) MAX-ACCESS read-write STATUS current DESCRIPTION "The start frequency of the idle spectrum from 5 MHZ to 42 MHZ for North American standard, 65 MHz for European standard and 10 MHz to 55 MHz for Japanese standard. If value 0 is retrieved for GET operation, it indicates this parameter has never been set. Value 0 is not allowed for SET operation." ::= { rdnCableSnrConfigEntry 1 } rdnCableSnrConfigIdleSpectrumStop OBJECT-TYPE SYNTAX Integer32 ( 0|5000000..65000000 ) MAX-ACCESS read-write STATUS current DESCRIPTION "The end frequency in idle spectrum. The upper limit is 42 MHz for North American standard, 65 MHz for European standard and 10 MHz to 55 MHz for Japanese standard. If value 0 is retrieved for GET operation, it indicates this parameter has never been set. Value 0 is not allowed for SET operation." ::= { rdnCableSnrConfigEntry 2 } rdnCableSnrConfigChannelWidth OBJECT-TYPE SYNTAX INTEGER { channelWidthNotConfiged(0), channelWidth2(400000), channelWidth3(800000), channelWidth4(1600000), channelWidth5(3200000), channelWidth6(6400000) } MAX-ACCESS read-write STATUS current DESCRIPTION "The spectrum channel width that the SNR tests will be evaluated. If value 0 is retrieved for GET operation, it indicates this parameter has never been set. Value 0 is not allowed for SET operation. " DEFVAL { 3200000 } ::= { rdnCableSnrConfigEntry 3 } rdnCableSnrConfigEqualization OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether equalization will be used for this SNR test. If this object has not be set, default value on will be displayed." DEFVAL { on } ::= { rdnCableSnrConfigEntry 4 } -- -- rdnCableSnrStartTable -- rdnCableSnrStartTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnCableSnrStartEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table allows activation of SNR test. These tests are performed on the ninth receiver of 2x8 CMTS for diagnostic purposes. This table applies to CMTS 2x8 cards, and to BSR2000. " ::= { rdnCableSnrGroup 2 } rdnCableSnrStartEntry OBJECT-TYPE SYNTAX RdnCableSnrStartEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of attributes for an entry in the rdnCableSnrStartEntry. An entry in this table exists for each sport of each 2x8 CMTS blade." INDEX { ifIndex } ::= { rdnCableSnrStartTable 1 } RdnCableSnrStartEntry ::= SEQUENCE { rdnCableSnrStart TruthValue, rdnCableSnrStartCmMac MacAddress } rdnCableSnrStart OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to true(1) causes SNR measurements. Reading the object with value true(1) indicates test in progress, and false(2) indicates no test in progress." ::= { rdnCableSnrStartEntry 1 } rdnCableSnrStartCmMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MAC address of the reference modem to be used for this SNR test. If left default, then a CM will be selected from a pool of registered CMs on this ifIndex. " DEFVAL { ''H } ::= { rdnCableSnrStartEntry 2 } -- -- SNR Results Group -- rdnCableSnrResultsGroup OBJECT IDENTIFIER ::= { rdnCableSnrGroup 3 } rdnCableSnrResultTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnCableSnrResultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the SNR data directly from the CMTS card. CMTS card only keeps the latest results from an SNR measurement. This table applies to CMTS 2x8 cards, and to BSR2000. " ::= { rdnCableSnrResultsGroup 1 } rdnCableSnrResultEntry OBJECT-TYPE SYNTAX RdnCableSnrResultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of results from a SNR measurement." INDEX { ifIndex, rdnCableSnrResultIndex } ::= { rdnCableSnrResultTable 1 } RdnCableSnrResultEntry ::= SEQUENCE { rdnCableSnrResultIndex Integer32, rdnCableSnrResultLastTime DateAndTime, rdnCableSnrResultCenterFreq Integer32, rdnCableSnrResultModulationProfile Integer32, rdnCableSnrResultModulationType INTEGER, rdnCableSnrResultEqualization INTEGER, rdnCableSnrResultSnrValue TenthdB } rdnCableSnrResultIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "A sequential index of 1 - n, and corresponding essentially to a display line number, as it would appear in the CLI. " ::= { rdnCableSnrResultEntry 1 } rdnCableSnrResultLastTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The date and time of the last SNR measurement." ::= { rdnCableSnrResultEntry 2 } rdnCableSnrResultCenterFreq OBJECT-TYPE SYNTAX Integer32 ( 5000000..65000000 ) UNITS "hertz" MAX-ACCESS read-only STATUS current DESCRIPTION "Center frequency used for the indicated SNR value." ::= { rdnCableSnrResultEntry 3 } rdnCableSnrResultModulationProfile OBJECT-TYPE SYNTAX Integer32 ( 1..600 ) MAX-ACCESS read-only STATUS current DESCRIPTION "Modulation profile used for this SNR test result." ::= { rdnCableSnrResultEntry 4 } rdnCableSnrResultModulationType OBJECT-TYPE SYNTAX INTEGER{ qpsk(1), qam16(2), qam8(3), qam32(4), qam64(5), qam128(6), qam256(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Modulation type used for this SNR test result." ::= { rdnCableSnrResultEntry 5 } rdnCableSnrResultEqualization OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether equalization used for this SNR test." ::= { rdnCableSnrResultEntry 6 } rdnCableSnrResultSnrValue OBJECT-TYPE SYNTAX TenthdB UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "SNR value for the indicated rdnCableSnrResultIndex." ::= { rdnCableSnrResultEntry 7 } rdnCableSnrResultModemTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnCableSnrResultModemEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the list of cable modem mac addresses that were selected / specified for the SNR test." ::= { rdnCableSnrResultsGroup 2 } rdnCableSnrResultModemEntry OBJECT-TYPE SYNTAX RdnCableSnrResultModemEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of modem mac addresses used for SNR test." INDEX { ifIndex } ::= { rdnCableSnrResultModemTable 1 } RdnCableSnrResultModemEntry ::= SEQUENCE { rdnCableSnrResultSelectedCmMac MacAddress } rdnCableSnrResultSelectedCmMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "MAC address of the reference modem that was selected for this SNR test. " ::= { rdnCableSnrResultModemEntry 1 } -- -- Object to enable/disable SNR traps -- rdnCableSnrTrapEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether SNR measurement traps should be generated. This includes: rdnCableSnrAbortTrap rdnCableSnrResultReadyTrap" DEFVAL { enabled } ::= { rdnCableSnrGroup 4 } -- -- SNR traps -- rdnCableSnrNotification OBJECT IDENTIFIER ::= { rdnCableSnrGroup 5 } rdnCableSnrNotificationPrefix OBJECT IDENTIFIER ::= { rdnCableSnrNotification 0 } rdnCableSnrAbortTrap NOTIFICATION-TYPE OBJECTS { ifIndex, rdnCardIfSlotNumber, rdnCardIfPortNumber, rdnCableSnrAbortReason} STATUS current DESCRIPTION " An event to report SNR measurement failure the slot/port and specify the SNR measurement abort reason." ::= { rdnCableSnrNotificationPrefix 1 } rdnCableSnrResultReadyTrap NOTIFICATION-TYPE OBJECTS { ifIndex, rdnCardIfSlotNumber, rdnCardIfPortNumber} STATUS current DESCRIPTION "An event to report SNR measurement completion on the slot/port and indicate the test result is ready to be viewed." ::= { rdnCableSnrNotificationPrefix 2 } -- rdnSnrThresholdTable -- -- This is an expansion table for rdnSpectrumGroupTable, listing SNR threshold -- values, per modulation type, for the associated Spectrum Group -- rdnSnrThresholdTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnSnrThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is an expansion table for the rdnSpectrumGroupTable, and defines the SNR thresholds for each possible modulation type. This table applies to CMTS 2x8 cards. " ::= { rdnCableSpectrumGroup 11 } rdnSnrThresholdEntry OBJECT-TYPE SYNTAX RdnSnrThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the rdnSnrThresholdTable. This is an expansion table for the rdnSpectrumGroupTable " INDEX { rdnSpectrumGroupName, rdnSnrThresholdModulationType } ::= {rdnSnrThresholdTable 1 } RdnSnrThresholdEntry ::= SEQUENCE { rdnSnrThresholdModulationType INTEGER, rdnSnrThresholdValue Unsigned32 } rdnSnrThresholdModulationType OBJECT-TYPE SYNTAX INTEGER { qpsk(1), qam16(2), -- ordering here to match rdnCableSnrResultModulationType qam8(3), -- and to be more consistent with docsIfCmtsModType qam32(4), qam64(5), qam128(6), qam256(7) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Modulation type for which this entry in the rdnSnrThresholdTable is setting a threshold value" ::= { rdnSnrThresholdEntry 1 } rdnSnrThresholdValue OBJECT-TYPE SYNTAX Unsigned32 (12 .. 37) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "The SNR threshold is used to determine if a channel is capable of operating error free in the modulation mode that is specified for data IUC in the configured modulation profile for the upstream receiver. A default SNR threshold is used for each modulation type. The operator can override this by configuring a different SNR threshold for a specific modulation type that is used in the primary or secondary modulation profile. This threshold is used to transition channel states. SNR thresholds are configurable with a resolution of 1dB. The following table lists default SNR thresholds for the different modulation modes, with no FEC: QPSK 16dB 8QAM 19dB 16QAM 22dB 32QAM 25dB 64QAM 28dB 128QAM 31dB 256QAM 34dB" ::= { rdnSnrThresholdEntry 2 } -- -- Object to enable/disable Spectrum Management Agility traps -- rdnCableSpectrumManagementTrapEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether Spectrum Management traps traps should be generated. This includes: rdnCableFrequencyHopTrap rdnCableFrequencyRollbackTrap rdnCableModulationProfileHopTrap rdnCableModulationProfileRollbackTrap rdnCableFrequencyRevertedTrap rdnCableModulationProfileRevertedTrap rdnCableChannelImpairedTrap rdnCableChannelNormalTrap rdnCableChannelPendingTrap rdnCableFrequencyHopFailureTrap rdnCableModulationProfileHopFailureTrap rdnCableSpectrumGroupConflictTrap" DEFVAL { enabled } ::= { rdnCableSpectrumGroup 12 } -- -- Spectrum Management Frequency/Modulation Agility/Rollback Traps -- rdnCableAgilityNotification OBJECT IDENTIFIER ::= { rdnCableSpectrumGroup 13 } rdnCableAgilityNotificationPrefix OBJECT IDENTIFIER ::= { rdnCableAgilityNotification 0 } -- Frequency Agility Trap rdnCableFrequencyHopTrap NOTIFICATION-TYPE OBJECTS { ifIndex, rdnCardIfSlotNumber, rdnCardIfPortNumber, rdnSpectrumGroupName, rdnSpectrumAgilityOldFrequency, docsIfUpChannelFrequency, docsIfUpChannelWidth, docsIfUpChannelModulationProfile } STATUS current DESCRIPTION "The BSR Spectrum Management feature has initiated an automatic Frequency change for purposes of noise avoidance. Severity level = warning(5). PARAMETERS: ifIndex is the interface index of the upstream physical channel that underwent an automatic frequency change. rdnCardIfSlotNumber is the chassis slot number of the CMTS card that is associated with the ifIndex parameter. rdnCardIfPortNumber is the port number of the receiver that is associated with the ifIndex parameter. rdnSpectrumGroupName is the Spectrum Group name associated with the upstream channel that underwent the frequency change. rdnSpectrumAgilityOldFrequency is the old frequency to which the upstream channel had been tuned, prior to the frequency change. Presumably, this frequency had an inadequate signal quality, which resulted in the automatic frequency change. docsIfUpChannelFrequency is the new frequency to which the upstream channel is tuned, following the frequency change. docsIfUpChannelWidth is the channel width for the upstream channel that underwent the frequency change. docsIfUpChannelModulationProfile is the modulation profile associated with the upstream channel that underwent the frequency change. " ::= { rdnCableAgilityNotificationPrefix 1 } -- Frequency Rollback Trap rdnCableFrequencyRollbackTrap NOTIFICATION-TYPE OBJECTS { ifIndex, rdnCardIfSlotNumber, rdnCardIfPortNumber, rdnSpectrumGroupName, rdnSpectrumAgilityOldFrequency, docsIfUpChannelFrequency, docsIfUpChannelWidth, docsIfUpChannelModulationProfile } STATUS current DESCRIPTION "The BSR Spectrum Management feature has initiated an automatic Frequency rollback, switching from the spare spectrum, back to the original frequency, after determining that signal-quality has been sufficiently restored on the original frequency. Severity level = notice(6). PARAMETERS: ifIndex is the interface index of the upstream physical channel that underwent an automatic frequency rollback. rdnCardIfSlotNumber is the chassis slot number of the CMTS card that is associated with the ifIndex parameter. rdnCardIfPortNumber is the port number of the receiver that is associated with the ifIndex parameter. rdnSpectrumGroupName is the Spectrum Group name associated with the upstream channel that underwent the frequency rollback. rdnSpectrumAgilityOldFrequency is the spare frequency to which the upstream channel had been tuned, prior to the frequency rollback. docsIfUpChannelFrequency is the original frequency to which the upstream channel is once again tuned, following a sufficient improvement in the signal quality. docsIfUpChannelWidth is the channel width for the upstream channel that underwent the frequency rollback. docsIfUpChannelModulationProfile is the modulation profile associated with the upstream channel that underwent the frequency rollback. " ::= { rdnCableAgilityNotificationPrefix 2 } -- Modulation Profile Agility Trap rdnCableModulationProfileHopTrap NOTIFICATION-TYPE OBJECTS { ifIndex, rdnCardIfSlotNumber, rdnCardIfPortNumber, rdnSpectrumGroupName, rdnSpectrumAgilityOldModulationProfile, docsIfUpChannelModulationProfile, docsIfUpChannelFrequency, docsIfUpChannelWidth } STATUS current DESCRIPTION "The BSR Spectrum Management feature has initiated an automatic modulation profile hop, for purposes of noise avoidance. Severity level = warning(5). PARAMETERS: ifIndex is the interface index of the upstream logical channel that underwent an automatic modulation profile hop. rdnCardIfSlotNumber is the chassis slot number of the CMTS card that is associated with the ifIndex parameter. rdnCardIfPortNumber is the port number of the receiver that is associated with the ifIndex parameter. rdnSpectrumGroupName is the Spectrum Group name associated with the upstream channel that underwent the modulation profile hop. rdnSpectrumAgilityOldModulationProfile is the modulation profile which the upstream channel had been using, prior to the modulation profile hop. docsIfUpChannelModulationProfile is the new modulation profile now in use the upstream channel, following the automatic modulation profile hop action. docsIfUpChannelFrequency is the frequency to which the upstream channel is currently tuned. docsIfUpChannelWidth is the channel width for the upstream channel that underwent the modulation profile hop." ::= { rdnCableAgilityNotificationPrefix 3 } -- Modulation Profile Rollback Trap rdnCableModulationProfileRollbackTrap NOTIFICATION-TYPE OBJECTS { ifIndex, rdnCardIfSlotNumber, rdnCardIfPortNumber, rdnSpectrumGroupName, rdnSpectrumAgilityOldModulationProfile, docsIfUpChannelModulationProfile, docsIfUpChannelFrequency, docsIfUpChannelWidth } STATUS current DESCRIPTION "The BSR Spectrum Management feature has initiated an automatic modulation profile rollback, for purposes of noise avoidance. Severity level = notice(6). PARAMETERS: ifIndex is the interface index of the upstream logical channel that underwent an automatic modulation profile rollback. rdnCardIfSlotNumber is the chassis slot number of the CMTS card that is associated with the ifIndex parameter. rdnCardIfPortNumber is the port number of the receiver that is associated with the ifIndex parameter. rdnSpectrumGroupName is the Spectrum Group name associated with the upstream channel that underwent the modulation profile rollback. rdnSpectrumAgilityOldModulationProfile is the modulation profile which the upstream channel had been using, prior to the modulation profile rollback. docsIfUpChannelModulationProfile is the new modulation profile now in use the upstream channel, following the automatic modulation profile rollback. docsIfUpChannelFrequency is the frequency to which the upstream channel is currently tuned. docsIfUpChannelWidth is the channel width for the upstream channel that underwent the modulation profile rollback." ::= { rdnCableAgilityNotificationPrefix 4 } -- Frequency Reverted Trap rdnCableFrequencyRevertedTrap NOTIFICATION-TYPE OBJECTS { ifIndex, rdnCardIfSlotNumber, rdnCardIfPortNumber, rdnSpectrumGroupName, rdnSpectrumAgilityFrequency, docsIfUpChannelFrequency, docsIfUpChannelWidth, docsIfUpChannelModulationProfile } STATUS current DESCRIPTION "The BSR Spectrum Management feature has detected an upstream port is shutdown or removed from a spectrum group. If the receiver is in any of the agile states, then the receiver is configured to the configured frequency. Severity level = warning(5). PARAMETERS: ifIndex is the interface index of the upstream physical channel that is underwent the frequency change. rdnCardIfSlotNumber is the chassis slot number of the CMTS card that is associated with the ifIndex parameter. rdnCardIfPortNumber is the port number of the receiver that is associated with the ifIndex parameter. rdnSpectrumGroupName is the Spectrum Group name associated with the upstream channel that underwent the frequency change. rdnSpectrumAgilityFrequency is the old frequency to which the upstream channel had been tuned to in agile state. docsIfUpChannelFrequency is the configured frequency to which the upstream channel is tuned, following the frequency change. docsIfUpChannelWidth is the channel width for the upstream channel that underwent the frequency change. docsIfUpChannelModulationProfile is the modulation profile associated with the upstream channel that underwent the frequency change. " ::= { rdnCableAgilityNotificationPrefix 5 } -- Modulation Profile Reverted Trap rdnCableModulationProfileRevertedTrap NOTIFICATION-TYPE OBJECTS { ifIndex, rdnCardIfSlotNumber, rdnCardIfPortNumber, rdnSpectrumGroupName, rdnSpectrumAgilityModulationProfile, docsIfUpChannelModulationProfile, docsIfUpChannelFrequency, docsIfUpChannelWidth } STATUS current DESCRIPTION " The BSR Spectrum Management feature has detected an upstream port is shutdown or removed from a spectrum group. If the receiver is in any of the agile states, then the receiver is configured to the configured modulation profile. Severity level = warning(5). PARAMETERS: ifIndex is the interface index of the upstream logical channel that underwent a modulation profile change. rdnCardIfSlotNumber is the chassis slot number of the CMTS card that is associated with the ifIndex parameter. rdnCardIfPortNumber is the port number of the receiver that is associated with the ifIndex parameter. rdnSpectrumGroupName is the Spectrum Group name associated with the upstream channel that underwent the modulation profile hop. rdnSpectrumAgilityModulationProfile is the modulation profile which the upstream channel had been using in agile state. docsIfUpChannelModulationProfile is the new modulation profile now in use the upstream channel, following the modulation profile changed. docsIfUpChannelFrequency is the frequency to which the upstream channel is currently tuned. docsIfUpChannelWidth is the channel width for the upstream channel that underwent the modulation profile change." ::= { rdnCableAgilityNotificationPrefix 6 } -- Channel Impaired Trap rdnCableChannelImpairedTrap NOTIFICATION-TYPE OBJECTS { ifIndex, rdnCardIfSlotNumber, rdnCardIfPortNumber, rdnSpectrumGroupName, docsIfUpChannelFrequency, docsIfUpChannelWidth, docsIfUpChannelModulationProfile } STATUS current DESCRIPTION "The BSR Spectrum Management feature has detected an upstream channel quality state transition to an impaired state, due to noise. Severity level = error(4). The channel will continue to operate in the impaired state, though in possibly degraded fashion, until such time as the BSR might be able to undertake a corrective frequency/modulation profile agility hop action, if such a hop action is configured. PARAMETERS: ifIndex is the interface index of the upstream physical channel that is impaired. rdnCardIfSlotNumber is the chassis slot number of the CMTS card that is associated with the ifIndex parameter. rdnCardIfPortNumber is the port number of the receiver that is associated with the ifIndex parameter. rdnSpectrumGroupName is the Spectrum Group name associated with the upstream channel that has become impaired. docsIfUpChannelFrequency is the frequency to which the impaired upstream channel is tuned. docsIfUpChannelWidth is the channel width for the upstream channel that has become impaired. docsIfUpChannelModulationProfile is the modulation profile associated with the upstream channel that has become impaired. " ::= { rdnCableAgilityNotificationPrefix 7 } -- Channel Normal Trap rdnCableChannelNormalTrap NOTIFICATION-TYPE OBJECTS { ifIndex, rdnCardIfSlotNumber, rdnCardIfPortNumber, rdnSpectrumGroupName, docsIfUpChannelFrequency, docsIfUpChannelWidth, docsIfUpChannelModulationProfile } STATUS current DESCRIPTION "The BSR Spectrum Management feature has detected an upstream channel quality state transition from an impaired state, to normal operating state. Severity level = notice(6). PARAMETERS: ifIndex is the interface index of the upstream physical channel that is no longer impaired. rdnCardIfSlotNumber is the chassis slot number of the CMTS card that is associated with the ifIndex parameter. rdnCardIfPortNumber is the port number of the receiver that is associated with the ifIndex parameter. rdnSpectrumGroupName is the Spectrum Group name associated with the upstream channel. docsIfUpChannelFrequency is the frequency for the upstream channel. docsIfUpChannelWidth is the channel width for the upstream channel. docsIfUpChannelModulationProfile is the modulation profile associated with the upstream channel." ::= { rdnCableAgilityNotificationPrefix 8 } -- Channel Pending Trap rdnCableChannelPendingTrap NOTIFICATION-TYPE OBJECTS { ifIndex, rdnCardIfSlotNumber, rdnCardIfPortNumber, rdnSpectrumGroupName, docsIfUpChannelFrequency, docsIfUpChannelWidth, docsIfUpChannelModulationProfile } STATUS current DESCRIPTION "The BSR Spectrum Management feature does not know an upstream channel quality state either Normal or Impaired. Once the state is known, it will transition out of Pending state. Severity level = notice(6). PARAMETERS: ifIndex is the interface index of the upstream physical channel that is in pending state. rdnCardIfSlotNumber is the chassis slot number of the CMTS card that is associated with the ifIndex parameter. rdnCardIfPortNumber is the port number of the receiver that is associated with the ifIndex parameter. rdnSpectrumGroupName is the Spectrum Group name associated with the upstream channel. docsIfUpChannelFrequency is the frequency for the upstream channel. docsIfUpChannelWidth is the channel width for the upstream channel. docsIfUpChannelModulationProfile is the modulation profile associated with the upstream channel." ::= { rdnCableAgilityNotificationPrefix 9 } -- Frequency Hop Failure Trap rdnCableFrequencyHopFailureTrap NOTIFICATION-TYPE OBJECTS { ifIndex, rdnCardIfSlotNumber, rdnCardIfPortNumber, rdnSpectrumGroupName, rdnSpectrumAgilityOldFrequency, docsIfUpChannelFrequency, docsIfUpChannelWidth, docsIfUpChannelModulationProfile, rdnCableAgilityHopAbortReason } STATUS current DESCRIPTION "The BSR Spectrum Management feature attempted to initiate an automatic frequency hop action, for purposes of noise avoidance, but the hop attempt failed. The frequency of the upstream channel is unchanged. Severity level = error(4). PARAMETERS: ifIndex is the interface index of the upstream physical channel that attempted an automatic frequency change. rdnCardIfSlotNumber is the chassis slot number of the CMTS card that is associated with the ifIndex parameter. rdnCardIfPortNumber is the port number of the receiver that is associated with the ifIndex parameter. rdnSpectrumGroupName is the Spectrum Group name associated with the upstream channel that attempted the frequency change. rdnSpectrumAgilityOldFrequency is the frequency to which the upstream channel was tuned, before the attempted frequency change. Presumably, this frequency had an inadequate signal quality, which resulted in the attempted frequency change. The receiver will still be tuned to this frequency, because of the hop failure. docsIfUpChannelFrequency is the new frequency which the failed hop action had attempted to set for the upstream channel docsIfUpChannelWidth is the channel width for the upstream channel that attempted the frequency change. docsIfUpChannelModulationProfile is the modulation profile associated with the upstream channel that attempted the frequency change. rdnCableAgilityHopAbortReason describes the reason that the frequency hop failed" ::= { rdnCableAgilityNotificationPrefix 10 } -- Modulation Profile Hop Failure Trap rdnCableModulationProfileHopFailureTrap NOTIFICATION-TYPE OBJECTS { ifIndex, rdnCardIfSlotNumber, rdnCardIfPortNumber, rdnSpectrumGroupName, rdnSpectrumAgilityOldModulationProfile, docsIfUpChannelModulationProfile, docsIfUpChannelFrequency, docsIfUpChannelWidth, rdnCableAgilityHopAbortReason } STATUS current DESCRIPTION "The BSR Spectrum Management feature attempted an automatic modulation profile hop, for purposes of noise avoidance, but the hop failed. Severity level = error(4). PARAMETERS: ifIndex is the interface index of the upstream logical channel that attempted an automatic modulation profile hop. rdnCardIfSlotNumber is the chassis slot number of the CMTS card that is associated with the ifIndex parameter. rdnCardIfPortNumber is the port number of the receiver that is associated with the ifIndex parameter. rdnSpectrumGroupName is the Spectrum Group name associated with the upstream channel that attempted the modulation profile hop. rdnSpectrumAgilityOldModulationProfile is the modulation profile the upstream channel (unchanged). docsIfUpChannelModulationProfile is the new modulation profile for the upstream channel, that the failed hop action had attempted to set. docsIfUpChannelFrequency is the frequency to which the upstream channel is currently tuned. docsIfUpChannelWidth is the channel width for the upstream channel that attempted the modulation profile hop. rdnCableAgilityHopAbortReason describes the reason that the frequency hop failed" ::= { rdnCableAgilityNotificationPrefix 11 } -- Spectrum Group Conflict Trap rdnCableSpectrumGroupConflictTrap NOTIFICATION-TYPE OBJECTS { rdnSpectrumGroupConflictType, rdnSpectrumGroupConflictDescription, rdnSpectrumGroupName } STATUS current DESCRIPTION "This trap reports an attempt by the operator to make a configuration change that would have created a conflict for a related spectrum group. Severity level = error(4). In all such cases, the attempted configuration attempt has been rejected, and the configuration is unchanged. PARAMETERS: rdnSpectrumGroupConflictType indicates the type of conflict that occurred. rdnSpectrumGroupConflictDescription is a string description to give detailed information about the conflict. rdnSpectrumGroupName is the Spectrum Group name involved in the failed configuration attempt." ::= { rdnCableAgilityNotificationPrefix 12 } -- -- rdnCableSnrNotificationObjects -- rdnCableSnrNotificationObjects OBJECT IDENTIFIER ::= { rdnCableSnrGroup 6 } rdnCableSnrAbortReason OBJECT-TYPE SYNTAX INTEGER { enableRxFreqInIdleSpectrum (0), addedRxFreqInIdleSpectrum (1), chanWidthChangeAffectsSNR (2), rxFreqChangeInIdleSpectrum (3), snrInProgressRxShutdown (4), spareChannelEvaluationRequest (5) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This entry contains the rdnCableSnrAbortTrap reason code: enableRxFreqInIdleSpectrum (0) indicates that the operator enabled a receiver, for which the assigned frequency might have conflicted with an SNR test that was that was already in progress, in the same spectrum group. addedRxFreqInIdleSpectrum (1) means that the operator added a new receiver to a spectrum group, for which the assigned frequency might have conflicted with an SNR test that was in progress. chanWidthChangeAffectsSNR (2) means that the operator set a new, larger channel width that might have conflicted with an SNR test that was already in progress. rxFreqChangeInIdleSpectrum (3) means that the operator set a new center frequency for a receiver, conflicting with the range of idle spectrum for an SNR test that was already in progress. snrInProgressRxShutdown (4) means that the operator shutdown the primary receiver, for which the RFSentry already had an SNR test in progress. spareChannelEvaluationRequest (5) means that the SNR test was automatically preempted by the software, in order to evaluate spare spectrum for purposes of performing an agility hopping action on an impaired channel." ::= { rdnCableSnrNotificationObjects 1 } rdnCableAgilityNotificationObjects OBJECT IDENTIFIER ::= { rdnCableSpectrumGroup 14 } rdnSpectrumAgilityOldFrequency OBJECT-TYPE SYNTAX Integer32 (0..1000000000) UNITS "hertz" MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The frequency to which the upstream channel was tuned, prior to the frequency agility hop or rollback. In the case of a frequency hop, this frequency presumably had inadequate signal quality, which caused a frequency change. In the case of a frequency rollback, this object represents the spare spectrum which had been in use, prior to the rollback. This frequency did not necessarily have any problem with signal quality. However, signal quality had improved under the original frequency sufficiently to allow a reversion to that frequency. " ::= { rdnCableAgilityNotificationObjects 1 } rdnSpectrumAgilityOldModulationProfile OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The modulation profile which was in use on the upstream channel prior to the modulation profile agility hop or rollback. In the case of a modulation profile hop, signal quality had been inadequate when the channel had been using this modulation profile. This resulted a hop action. In the case of a modulation profile rollback, this object represents the modulation profile that had been in use prior to the rollback, and which had been previously selected by a modulation profile agility hop action. The old modulation profile did not necessarily have any problem with signal quality. However, the original modulation profile improved sufficiently to allow a reversion to that profile." ::= { rdnCableAgilityNotificationObjects 2 } rdnCableAgilityHopAbortReason OBJECT-TYPE SYNTAX INTEGER { invalidSnrResults(0), spareFrequencyInUse(1), spareFrequencyPoorQuality(2), snrTimeout(3), modProfileChanTypeMismatch(4), modProfileNotOptimal(5) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This entry contains a reason code for the rdnCableFrequencyHopFailureTrap or rdnCableModulationProfileHopFailureTrap. invalidSnrResults(0) means that the SNR measurement of the spare frequency failed, for an attempted frequency hop, for any reason. spareFrequencyInUse(1) means that the spare frequency assessed by the CMTS card is in use by another receiver in the spectrum group. spareFrequencyPoorQuality(2) means that the spare frequency for an attempted frequency hop was too noisy to run at the optimal modulation level, and needed to be downgraded by an additional modulation hop. The frequency hop action itself DID occur, and should have produced a separate rdnCableFrequencyHopTrap. The rdnCableFrequencyHopFailureTrap in this case is simply warning that the new frequency is running a lower modulation. snrTimeout(3) means that the SNR measurement did not complete on the spare spectrum, for a frequency hop (no response). modProfileChanTypeMismatch(4) means that the BSR attempted to do a modulation profile hop, and found a number of configured configured hops, but none of the profiles had an appropriate channel type. No modulation profile hop took place. For this status, the docsIfUpChannelModulationProfile varbind will show a dummy value of 0. modProfileNotOptimal(5) means that a modulation profile hop DID take place, but the BSR could not find a profile having a modulation level that was appropriate for the impaired channel, based on the configured SNR threshold levels. The BSR did the next-best thing, by using the lowest of the modulation level that it could find. " ::= { rdnCableAgilityNotificationObjects 3 } rdnSpectrumGroupConflictType OBJECT-TYPE SYNTAX INTEGER { newMemberFreqOverlap(1), invalidChannelTypeMix(2), freqOverlapsExistingMember(3), hopFrequencyInUse(4), hopModulationInUse(5), hopSpareAssessInProgress(6), chanIsAgile(7), chanWidthOverlap(8), internalError(9) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This entry contains the type of conflict that resulted in a rdnCableSpectrumGroupConflictTrap: newMemberFreqOverlap (1) indicates an attempt to add a member channel to a spectrum group, when the assigned frequency of the prospective member channel would have overlapped with an existing frequency hop action definition, or the frequency in use by an existing member channel. invalidChannelTypeMix (2) indicates an attempt to add a 2x8 CMTS member channel to a spectrum group that contains 1x4 or 1x8 CMTS channels, or vice-versa. freqOverlapsExistingMember (3) indicates an attempt to set a frequency for a channel that is a member of a spectrum group, and the frequency would conflict with an another channel in the same spectrum group that is already using that frequency. hopFrequencyInUse (4) indicates an attempt to delete a hop action frequency or band from a spectrum group configuration, when a frequency in this range is currently in use as a result of a hopping action. In order to achieve the desired deletion, the operator must explicitly remove the frequency from use, before updating the spectrum group. hopModulationInUse(5) indicates an attempt to delete a modulation profile hop action from a spectrum group configuration, when the modulation profile is already in use, as a result of a hopping action. hopSpareAssessInProgress(6) indicates that the requested operation could not be performed because a spare channel assessment was already in progress. channelIsAgile(7) means that the requested operation on a member channel is not allowed because the channel is in a frequency or modulation-agile state. chanWidthOverlap(8) means that an attempted change to a channel width of a member channel would cause a conflict within the Spectrum Group, for another member channel or a configured hop action. internalError(9) implies an internal software or hardware error. This is an unexpected error type, so report to Motorola, if it ever occurs. " ::= { rdnCableAgilityNotificationObjects 4 } rdnSpectrumGroupConflictDescription OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Describes the exact failure cause for an attempted configuration change that would have resulted in a conflict for the associated Spectrum Group. This includes applicable information such as interface index values, frequencies, and modulation profiles that are involved. " ::= { rdnCableAgilityNotificationObjects 5 } rdnSpectrumAgilityFrequency OBJECT-TYPE SYNTAX Integer32 (0..1000000000) UNITS "hertz" MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The frequency to which the upstream channel was tuned for the frequency agility." ::= { rdnCableAgilityNotificationObjects 6 } rdnSpectrumAgilityModulationProfile OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The modulation profile which was in use on the upstream channel for the modulation profile agility." ::= { rdnCableAgilityNotificationObjects 7 } rdnModemExclusionGroup OBJECT IDENTIFIER ::= { rdnCableSpectrumGroup 15 } rdnModemExclusionTimeStamp OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "Timestamp indicating when this Cable Modem Exclusion List (rdnModemExclusionTable) was built " ::= { rdnModemExclusionGroup 1 } --- rdnModemExclusionTable: --- --- Display Modem Exclusion List --- This is a counterpart to the CLI --- "show cable spectrum-group sg1 modem-exclusion-list" rdnModemExclusionTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnModemExclusionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Show list of low SNR modems(s) not allowed to be used for channel assessment" ::= { rdnModemExclusionGroup 2 } rdnModemExclusionEntry OBJECT-TYPE SYNTAX RdnModemExclusionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of attributes for an entry in the rdnModemExclusionEntry. This table has 3 index values: 1) Spectrum group id. 2) ifIndex is the interface index of the upstream physical channel that is associated with the spectrum group. 3) Modem Exclusion index for each upstream. " INDEX { rdnSpectrumGroupId, ifIndex, rdnModemExclusionEntryIndex } ::= {rdnModemExclusionTable 1} RdnModemExclusionEntry ::= SEQUENCE { rdnModemExclusionEntryIndex Integer32, rdnModemExclusionSpectrumGroupName DisplayString, rdnModemExclusionSpectrumGroupId Unsigned32, rdnModemExclusionSpectrumGroupIface DisplayString, rdnModemExclusionMacAddress MacAddress, rdnModemExclusionSnrValue TenthdB, rdnModemExclusionIPv4Addr InetAddressIPv4, rdnModemExclusionIPv6Addr InetAddressIPv6 } rdnModemExclusionEntryIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "A sequential index of 1 - n, and corresponding essentially to a display line number, as it would appear in the CLI. " ::= { rdnModemExclusionEntry 1 } rdnModemExclusionSpectrumGroupName OBJECT-TYPE SYNTAX DisplayString ( SIZE (1..20) ) MAX-ACCESS read-only STATUS current DESCRIPTION "The text name of the spectrum group, associated with this excluded modem" ::= { rdnModemExclusionEntry 2 } rdnModemExclusionSpectrumGroupIface OBJECT-TYPE SYNTAX DisplayString ( SIZE (1..20) ) MAX-ACCESS read-only STATUS current DESCRIPTION "The text name of the cable interface, associated with this excluded modem" ::= { rdnModemExclusionEntry 3 } rdnModemExclusionSpectrumGroupId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number index for the spectrum group, that is associated with the excluded modem. " ::= { rdnModemExclusionEntry 4 } rdnModemExclusionMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "MAC address of Cable Modem on Exclusion List. " ::= { rdnModemExclusionEntry 5 } rdnModemExclusionSnrValue OBJECT-TYPE SYNTAX TenthdB UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "SNR value for Cable Modem on the Exclusion List" ::= { rdnModemExclusionEntry 7 } rdnModemExclusionIPv4Addr OBJECT-TYPE SYNTAX InetAddressIPv4 MAX-ACCESS read-only STATUS current DESCRIPTION "IPv4 address of this Cable Modem on the Exclusion List." ::= { rdnModemExclusionEntry 8 } rdnModemExclusionIPv6Addr OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-only STATUS current DESCRIPTION "IPv6 address of this Cable Modem on the Exclusion List." ::= { rdnModemExclusionEntry 9 } rdnReferenceModemGroup OBJECT IDENTIFIER ::= { rdnCableSpectrumGroup 16 } --- rdnReferenceModemTable: --- --- Display Reference Modem List --- This is a counterpart to the CLI --- "show cable spectrum-group sg1 reference-modem" rdnReferenceModemTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnReferenceModemEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Show reference modems(s) being used for channel assessment" ::= { rdnReferenceModemGroup 1 } rdnReferenceModemEntry OBJECT-TYPE SYNTAX RdnReferenceModemEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of attributes for an entry in the rdnReferenceModemEntry. This table has 2 index values: 1) Spectrum group id. 2) ifIndex is the interface index of the upstream physical channel that is associated with the spectrum group. 3) Reference Modem index for each upstream. " INDEX { rdnSpectrumGroupId, ifIndex, rdnReferenceModemEntryIndex } ::= {rdnReferenceModemTable 1} RdnReferenceModemEntry ::= SEQUENCE { rdnReferenceModemEntryIndex Integer32, rdnReferenceModemSpectrumGroupName DisplayString, rdnReferenceModemSpectrumGroupId Unsigned32, rdnReferenceModemSpectrumGroupIface DisplayString, rdnReferenceModemMacAddress MacAddress, rdnReferenceModemSnrValue TenthdB, rdnReferenceModemIPv4Addr InetAddressIPv4, rdnReferenceModemIPv6Addr InetAddressIPv6 } rdnReferenceModemEntryIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The modem index into the reference modem array." ::= { rdnReferenceModemEntry 1 } rdnReferenceModemSpectrumGroupName OBJECT-TYPE SYNTAX DisplayString ( SIZE (1..20) ) MAX-ACCESS read-only STATUS current DESCRIPTION "The text name of the spectrum group, associated with this reference modem " ::= { rdnReferenceModemEntry 2 } rdnReferenceModemSpectrumGroupId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number index for the spectrum group, that is associated with the reference modem. " ::= { rdnReferenceModemEntry 3 } rdnReferenceModemSpectrumGroupIface OBJECT-TYPE SYNTAX DisplayString ( SIZE (1..20) ) MAX-ACCESS read-only STATUS current DESCRIPTION "The text name of the cable interface, associated with this excluded modem" ::= { rdnReferenceModemEntry 4 } rdnReferenceModemMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "MAC address of Reference Modem. " ::= { rdnReferenceModemEntry 5 } rdnReferenceModemSnrValue OBJECT-TYPE SYNTAX TenthdB UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "SNR value for Reference Modem" ::= { rdnReferenceModemEntry 6 } rdnReferenceModemIPv4Addr OBJECT-TYPE SYNTAX InetAddressIPv4 MAX-ACCESS read-only STATUS current DESCRIPTION "IPv4 address of this Reference Modem." ::= { rdnReferenceModemEntry 7 } rdnReferenceModemIPv6Addr OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-only STATUS current DESCRIPTION "IPv6 address of this Reference Modem." ::= { rdnReferenceModemEntry 8 } -- -- SNR loop test -- rdnCableSnrLoopTestTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnCableSnrLoopTestEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table allows configuration of automatically repeated SNR tests, using a specified loop count and a specified center frequency. These tests are performed on the ninth receiver for diagnostic purposes. This table applies to CMTS 2x8 cards, and to BSR2000. " ::= { rdnCableSnrGroup 7 } rdnCableSnrLoopTestEntry OBJECT-TYPE SYNTAX RdnCableSnrLoopTestEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of attributes for an entry in the rdnCableSnrLoopTestEntry. An entry in this table exists for each slot/port of 2x8 CMTS." INDEX { ifIndex } ::= { rdnCableSnrLoopTestTable 1} RdnCableSnrLoopTestEntry ::= SEQUENCE { rdnCableSnrLoopTestLoopCount INTEGER, rdnCableSnrLoopTestCenterFrequency Integer32, rdnCableSnrLoopTestChannelWidth INTEGER, rdnCableSnrLoopTestCmMac MacAddress, rdnCableSnrLoopTestIngressCancellation INTEGER, rdnCableSnrLoopTestEqualization INTEGER, rdnCableSnrLoopTestDataPattern INTEGER, rdnCableSnrLoopStart TruthValue } rdnCableSnrLoopTestLoopCount OBJECT-TYPE SYNTAX INTEGER (0 | 1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of times to repeat SNR measurements, using a configuration as specified by the rdnCableSnrLoopTestTable. A value of 0 is read-only, and means that the loop test is not configured" ::= { rdnCableSnrLoopTestEntry 1 } rdnCableSnrLoopTestCenterFrequency OBJECT-TYPE SYNTAX Integer32 (0 | 5000000..65000000 ) UNITS "hertz" MAX-ACCESS read-write STATUS current DESCRIPTION "The center frequency from 5 MHZ to 42 MHZ for North American standard, or 65 MHz for European standard. If value 0 is retrieved for GET operation, it indicates this parameter has never been set. Value 0 is not allowed for SET operation." ::= { rdnCableSnrLoopTestEntry 2 } rdnCableSnrLoopTestChannelWidth OBJECT-TYPE SYNTAX INTEGER { channelWidthNotConfiged(0), channelWidth2(400000), channelWidth3(800000), channelWidth4(1600000), channelWidth5(3200000), channelWidth6(6400000) } MAX-ACCESS read-write STATUS current DESCRIPTION "The spectrum channel width that the SNR tests will be evaluated. If value 0 is retrieved for GET operation, it indicates this parameter has never been set. Value 0 is not allowed for SET operation. " DEFVAL { 3200000 } ::= { rdnCableSnrLoopTestEntry 3 } rdnCableSnrLoopTestCmMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MAC address of the reference modem to be used for this SNR loop test. If left to default, then a CM will be selected from a pool of registered CMs on this ifIndex. " DEFVAL { '000000000000'H } ::= { rdnCableSnrLoopTestEntry 4 } rdnCableSnrLoopTestIngressCancellation OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether ingress cancellation will be used for this SNR test." DEFVAL { off } ::= { rdnCableSnrLoopTestEntry 5 } rdnCableSnrLoopTestEqualization OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether equalization will be used for this SNR test." DEFVAL { on } ::= { rdnCableSnrLoopTestEntry 6 } rdnCableSnrLoopTestDataPattern OBJECT-TYPE SYNTAX INTEGER { ranging(1) -- Other patterns will be provided in future } MAX-ACCESS read-write STATUS current DESCRIPTION "Data pattern to use for the SNR loop measurements." DEFVAL { ranging } ::= { rdnCableSnrLoopTestEntry 7 } rdnCableSnrLoopStart OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to true(1) causes repeated SNR measurements, with a loop count as indicated by rdnCableSnrLoopTestLoopCount, and using a configuration as specified by the other row members of rdnCableSnrLoopTestTable. Reading the object with value true(1) indicates test in progress, and false(2) indicates no test in progress." ::= { rdnCableSnrLoopTestEntry 8 } -- -- rdnCableSnrLoopResultTable -- rdnCableSnrLoopResultTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnCableSnrLoopResultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the SNR loop test results, for a test previously initiated through the rdnCableSnrLoopTestTable. Results are reported directly from the CMTS card(s). This table applies to CMTS 2x8 cards, and to BSR2000. " ::= { rdnCableSnrGroup 8 } rdnCableSnrLoopResultEntry OBJECT-TYPE SYNTAX RdnCableSnrLoopResultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of results from SNR loop test measurements." INDEX { ifIndex } ::= { rdnCableSnrLoopResultTable 1 } RdnCableSnrLoopResultEntry ::= SEQUENCE { rdnCableSnrLoopResultLoopCount INTEGER, rdnCableSnrLoopResultCenterFreq Integer32, rdnCableSnrLoopResultChannelWidth INTEGER, rdnCableSnrLoopResultModulationProfile Integer32, rdnCableSnrLoopResultCmMac MacAddress, rdnCableSnrLoopResultIngressCancellation INTEGER, rdnCableSnrLoopResultEqualization INTEGER, rdnCableSnrLoopResultDataPattern INTEGER, rdnCableSnrLoopResultMaxSnrValue TenthdB, rdnCableSnrLoopResultMinSnrValue TenthdB, rdnCableSnrLoopResultAvSnrValue TenthdB, rdnCableSnrLoopResultLastTime DateAndTime } rdnCableSnrLoopResultLoopCount OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times that SNR looping test repeated measurements." ::= { rdnCableSnrLoopResultEntry 1 } rdnCableSnrLoopResultCenterFreq OBJECT-TYPE SYNTAX Integer32 ( 5000000..65000000 ) UNITS "hertz" MAX-ACCESS read-only STATUS current DESCRIPTION "Center frequency associated with the max/min/average SNR values." ::= { rdnCableSnrLoopResultEntry 2 } rdnCableSnrLoopResultChannelWidth OBJECT-TYPE SYNTAX INTEGER { channelWidthNotConfiged(0), channelWidth2(400000), channelWidth3(800000), channelWidth4(1600000), channelWidth5(3200000), channelWidth6(6400000) } MAX-ACCESS read-only STATUS current DESCRIPTION "The spectrum channel width associated with the SNR max/min/average values. " ::= { rdnCableSnrLoopResultEntry 3 } rdnCableSnrLoopResultModulationProfile OBJECT-TYPE SYNTAX Integer32 ( 1..600 ) MAX-ACCESS read-only STATUS current DESCRIPTION "Modulation profile associated with the SNR max/min/average values." ::= { rdnCableSnrLoopResultEntry 4 } rdnCableSnrLoopResultCmMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "MAC address of the reference modem that was selected for this SNR loop test." ::= { rdnCableSnrLoopResultEntry 5 } rdnCableSnrLoopResultIngressCancellation OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether ingress cancellation used for this SNR loop test." ::= { rdnCableSnrLoopResultEntry 6 } rdnCableSnrLoopResultEqualization OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether equalization was used for this SNR loop test." ::= { rdnCableSnrLoopResultEntry 7 } rdnCableSnrLoopResultDataPattern OBJECT-TYPE SYNTAX INTEGER { ranging(1) -- Other patterns will be provided in future } MAX-ACCESS read-only STATUS current DESCRIPTION "Data pattern that was used for the SNR loop measurements." ::= { rdnCableSnrLoopResultEntry 8 } rdnCableSnrLoopResultMaxSnrValue OBJECT-TYPE SYNTAX TenthdB UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum SNR value for this loop test" ::= { rdnCableSnrLoopResultEntry 9 } rdnCableSnrLoopResultMinSnrValue OBJECT-TYPE SYNTAX TenthdB UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum SNR value for this loop test" ::= { rdnCableSnrLoopResultEntry 10 } rdnCableSnrLoopResultAvSnrValue OBJECT-TYPE SYNTAX TenthdB UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Average SNR value for this loop test" ::= { rdnCableSnrLoopResultEntry 11 } rdnCableSnrLoopResultLastTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The date and time when last SNR loop test began." ::= { rdnCableSnrLoopResultEntry 12 } --- --- mod prof table --- rdnCableSnrModulationProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF RdnCableSnrModulationProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table allows configuration of the modulation profile for SNR and LOOP tests. This table applies to CMTS 2x8 cards, and to BSR2000. " ::= { rdnCableSnrGroup 9 } rdnCableSnrModulationProfileEntry OBJECT-TYPE SYNTAX RdnCableSnrModulationProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of modulation profiles for the CMTS cards. The table is indexed by slotNo (0 to 15)." INDEX { rdnSlotNumber } ::= { rdnCableSnrModulationProfileTable 1 } RdnCableSnrModulationProfileEntry ::= SEQUENCE { rdnCableSnrModulationProfile Integer32 } rdnCableSnrModulationProfile OBJECT-TYPE SYNTAX Integer32 (1..600) MAX-ACCESS read-write STATUS current DESCRIPTION "The modulation profile used for any SNR / LOOP test on this card. If this object has not be set, default value 1 will be displayed." DEFVAL { 1 } ::= { rdnCableSnrModulationProfileEntry 1 } END