VPLS-BGP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, transmission FROM SNMPv2-SMI -- RFC 2578 MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF -- RFC 2580 RowStatus, StorageType FROM SNMPv2-TC -- RFC 2579 SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- RFC 3411 pwIndex FROM PW-STD-MIB -- RFC 5601 vplsConfigIndex FROM VPLS-GENERIC-MIB ; vplsBgpMIB MODULE-IDENTITY LAST-UPDATED "201405191200Z" -- 19 May 2014 12:00:00 GMT ORGANIZATION "Layer 2 Virtual Private Networks (L2VPN) Working Group" CONTACT-INFO " V. J. Shah Email: vshah@juniper.net The L2VPN Working Group (email distribution l2vpn@ietf.org, http://www.ietf.org/wg/l2vpn/charter/) " DESCRIPTION "Copyright (c) 2014 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info). The initial version of this MIB module was published in RFC 7257; for full legal notices see the RFC itself. This MIB module contains managed object definitions for BGP signaled Virtual Private LAN Service as in RFC 4761. This MIB module enables the use of any underlying pseudowire network." -- Revision history. REVISION "201405191200Z" -- 19 May 2014 12:00:00 GMT DESCRIPTION "Initial version published as part of RFC 7257." ::= { transmission 276 } -- Top-level components of this MIB. -- Tables, Scalars vplsBgpObjects OBJECT IDENTIFIER ::= { vplsBgpMIB 1 } -- Conformance vplsBgpConformance OBJECT IDENTIFIER ::= { vplsBgpMIB 2 } -- Vpls Bgp Config Table vplsBgpConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF VplsBgpConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies information for configuring and monitoring BGP-specific parameters for Virtual Private LAN Service (VPLS)." ::= { vplsBgpObjects 1 } vplsBgpConfigEntry OBJECT-TYPE SYNTAX VplsBgpConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table represents BGP-specific information for Virtual Private LAN Service (VPLS) in a packet network. It is indexed by vplsConfigIndex, which uniquely identifies a single instance of a VPLS service. A row is automatically created when a VPLS service is created that is configured to use BGP signaling. All of the writable object values can be changed when vplsConfigRowStatus is in the active(1) state. " INDEX { vplsConfigIndex } ::= { vplsBgpConfigTable 1 } VplsBgpConfigEntry ::= SEQUENCE { vplsBgpConfigVERangeSize Unsigned32 } vplsBgpConfigVERangeSize OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the size of the range of VPLS Edge Identifier (VE ID) in this VPLS service. This number controls the size of the label block advertised for this VE by the PE. A value of 0 indicates that the range is not configured and the PE derives the range value from received advertisements from other PEs. The VE ID takes 2 octets in VPLS BGP NLRI according to RFC 4761. Hence we have limited the range of this object to 65535." DEFVAL { 0 } ::= { vplsBgpConfigEntry 1 } -- Vpls Edge Device (VE) Identifier Table vplsBgpVETable OBJECT-TYPE SYNTAX SEQUENCE OF VplsBgpVEEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table associates VPLS Edge devices to a VPLS service" ::= { vplsBgpObjects 2 } vplsBgpVEEntry OBJECT-TYPE SYNTAX VplsBgpVEEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created for each VE ID configured on a PE for a particular VPLS service instance. Entries in this table may be created or deleted through SNMP, as side effects of console or other non-SNMP management commands, or upon learning via autodiscovery. It is optional for the agent to allow entries to be created that point to nonexistent entries in vplsConfigTable." INDEX { vplsConfigIndex, vplsBgpVEId } ::= { vplsBgpVETable 1 } VplsBgpVEEntry ::= SEQUENCE { vplsBgpVEId Unsigned32, vplsBgpVEName SnmpAdminString, vplsBgpVEPreference Unsigned32, vplsBgpVERowStatus RowStatus, vplsBgpVEStorageType StorageType } vplsBgpVEId OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A secondary index identifying a VE within an instance of a VPLS service. The VE ID takes 2 octets in VPLS BGP NLRI according to RFC 4761. Hence, we have limited the range of this object to 65535." ::= { vplsBgpVEEntry 1 } vplsBgpVEName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "Descriptive name for the site or user-facing PE (U-PE) associated with this VE ID." DEFVAL { "" } ::= { vplsBgpVEEntry 2 } vplsBgpVEPreference OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the preference of the VE ID on this Provider Edge (PE) if the site is multihomed and VE ID is reused." DEFVAL { 0 } ::= { vplsBgpVEEntry 3 } vplsBgpVERowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table. All other objects in this row must be set to valid values before this object can be set to active(1). When a row in this table is in active(1) state, no objects in that row can be modified except vplsBgpSiteRowStatus." ::= { vplsBgpVEEntry 5 } vplsBgpVEStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This variable indicates the storage type for this row." DEFVAL { volatile } ::= { vplsBgpVEEntry 6 } -- VPLS BGP PW Binding Table vplsBgpPwBindTable OBJECT-TYPE SYNTAX SEQUENCE OF VplsBgpPwBindEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides BGP-specific information for an association between a VPLS service and the corresponding pseudowires. A service can have more than one pseudowire association. Pseudowires are defined in the pwTable." ::= { vplsBgpObjects 3 } vplsBgpPwBindEntry OBJECT-TYPE SYNTAX VplsBgpPwBindEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each row represents an association between a VPLS instance and one or more pseudowires defined in the pwTable. Each index is unique in describing an entry in this table. However, both indexes are required to define the one to many association of service to pseudowire. An entry in this table in instantiated only when BGP signaling is used to configure VPLS service. Each entry in this table provides BGP-specific information for the VPLS represented by vplsConfigIndex." INDEX { vplsConfigIndex, pwIndex } ::= { vplsBgpPwBindTable 1 } VplsBgpPwBindEntry ::= SEQUENCE { vplsBgpPwBindLocalVEId Unsigned32, vplsBgpPwBindRemoteVEId Unsigned32 } vplsBgpPwBindLocalVEId OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Identifies the local VE with which this pseudowire is associated. The VE ID takes 2 octets in VPLS BGP NLRI according to RFC 4761. Hence, we have limited the range of this object to 65535." ::= { vplsBgpPwBindEntry 1 } vplsBgpPwBindRemoteVEId OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Identifies the remote VE with which this pseudowire is associated. The VE ID takes 2 octets in VPLS BGP NLRI according to RFC 4761. Hence, we have limited the range of this object to 65535." ::= { vplsBgpPwBindEntry 2 } -- Conformance Section -- Compliance requirement for fully compliant implementations vplsBgpCompliances OBJECT IDENTIFIER ::= { vplsBgpConformance 1 } vplsBgpModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance requirement for implementations that provide full support for VPLS-BGP-MIB. Such devices can then be monitored and configured using this MIB module." MODULE -- this module MANDATORY-GROUPS { vplsBgpConfigGroup, vplsBgpVEGroup, vplsBgpPwBindGroup } ::= { vplsBgpCompliances 1 } -- Compliance requirement for read-only implementations. vplsBgpModuleReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance requirement for implementations that only provide read-only support for VPLS-BGP-MIB. Such devices can then be monitored but cannot be configured using this MIB modules." MODULE -- this module MANDATORY-GROUPS { vplsBgpConfigGroup, vplsBgpVEGroup, vplsBgpPwBindGroup } OBJECT vplsBgpConfigVERangeSize MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vplsBgpVEName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vplsBgpVEPreference MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vplsBgpVERowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { vplsBgpCompliances 2 } -- Units of conformance. vplsBgpGroups OBJECT IDENTIFIER ::= { vplsBgpConformance 2 } vplsBgpConfigGroup OBJECT-GROUP OBJECTS { vplsBgpConfigVERangeSize } STATUS current DESCRIPTION "The group of objects supporting configuration of L2VPN VPLS services using BGP." ::= { vplsBgpGroups 1 } vplsBgpVEGroup OBJECT-GROUP OBJECTS { vplsBgpVEName, vplsBgpVEPreference, vplsBgpVERowStatus, vplsBgpVEStorageType } STATUS current DESCRIPTION "The group of objects supporting management of VPLS Edge devices for L2VPN VPLS services using BGP." ::= { vplsBgpGroups 2 } vplsBgpPwBindGroup OBJECT-GROUP OBJECTS { vplsBgpPwBindLocalVEId, vplsBgpPwBindRemoteVEId } STATUS current DESCRIPTION "The group of objects supporting management of pseudowires for L2VPN VPLS services using BGP." ::= { vplsBgpGroups 3 } END