RAD-RadBgp-MIB DEFINITIONS ::= BEGIN -- It is RAD's intent to encourage the widespread use of -- this Specification in connection with the management of -- RAD products. RAD grants vendors, end-users, -- and other interested parties a non-exclusive license to -- use this Specification in connection with the management -- of RAD products. -- This Specification is supplied "as is," and RAD makes -- no warranty, either express or implied, as to the use, -- operation, condition, or performance of the Specification. IMPORTS InetAddressType, InetAddress, InetAddressPrefixLength, InetPortNumber FROM INET-ADDRESS-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB Integer32, Gauge32, Unsigned32, OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE FROM SNMPv2-SMI TEXTUAL-CONVENTION, DisplayString, RowStatus FROM SNMPv2-TC radSysRtrEvents, alarmEventLogSourceName, alarmEventLogAlarmOrEventId, alarmEventLogDescription, alarmEventLogSeverity, alarmEventLogDateAndTime, alarmEventReason FROM RAD-GEN-MIB TruthValue FROM SNMPv2-TC radRouter, RtrSafi, rtrConfigRoutingName FROM RAD-SubRtr-MIB; rtrBgp MODULE-IDENTITY LAST-UPDATED "201503121308Z" -- March 12, 2015 ORGANIZATION "RAD Data Communications Ltd." CONTACT-INFO "System Department Email: mibs@rad.com Postal: RAD Data Communications Ltd. 24 Raoul Wallenberg St. Tel-Aviv 6971920 Israel Phone: +972-3-645-5421 Fax: +972-3-760-7844" DESCRIPTION "Router BGP MIB." ::= { radRouter 4 } -- ************************************************ -- Interfaces Group -- Link Layer (layer 2) Configuration MIB -- ************************************************ -- The following MIB group is used by the Management/Configuration -- station to configure the device interfaces, -- physicals as well as virtuals. -- Each entry in the rtrDynamicIfConfigTable should have one of -- the extended rtType. -- It will also have a corresponding entry in the standard iftable. -- The implementation uses these inputs to build the interface -- layer of the device. The output is reflected in the -- ifTable and ifStackTable which are implementation dependent. -- rtrBgp OBJECT IDENTIFIER ::= { radRouter 4 } BgpAutonomousSystemNumber ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An autonomous System Number. If bgpAsSize is two-octet, the range is 0..65535. If it is four-octet, it is the full range of Unsigned32." SYNTAX Unsigned32 BgpIdentifier ::= TEXTUAL-CONVENTION DISPLAY-HINT "4x" STATUS current DESCRIPTION "The representation of a BGP Identifier." SYNTAX OCTET STRING (SIZE (4)) BgpPeerStates ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The current state of a connection to a BGP peer." SYNTAX INTEGER { idle(1), connect(2), active(3), opensent(4), openconfirm(5), established(6) } BgpCapabilities ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The capabilities advertised by a BGP instance." SYNTAX BITS { reserved0(0), -- reserved mpIpv4Unicast(1), -- multiprotocol BGP support -- for IPv4 unicast routes mpIpv4Multicast(2), -- multiprotocol BGP support -- for IPv4 multicast routes mpIpv4Vpn(3), -- multiprotocol BGP support -- for IPv4 VPN routes reserved4(4), -- reserved mpIpv6Unicast(5), -- multiprotocol BGP support -- for IPv6 unicast routes mpIpv6Multicast(6), -- multiprotocol BGP support -- for IPv6 multicast routes mpIpv6Vpn(7), -- multiprotocol BGP support -- for IPv6 VPN routes reserved8(8), -- reserved routeRefresh(9), -- support for Route Refresh -- messages gracefulRestart(10), -- support for graceful restart -- processing routeRefreshCisco(11), -- support for pre-standard -- (Cisco) Route Refresh -- messages outboundRouteFilter(12), -- support for Outbound Route -- Filtering, for one or more -- AFI/SAFI types outboundRouteFilterCisco(13), -- support for pre-standard -- (Cisco) Outbound Route -- Filtering, for one or more -- AFI/SAFI types fourOctetAs(14) -- support for four-octet AS -- numbers } BgpPermitOrDeny ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Whether the behavior is to permit or deny." SYNTAX INTEGER { permit(1), -- Unmatched routes are permitted deny(2) -- Unmatched routes are denied } BgpSafi ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The representation of a BGP Safi (Sub-Address Family Identifier)" SYNTAX INTEGER { unicast(1), multicast(2), both(3), mplsBgpVpn(128) } BgpCommunity ::= TEXTUAL-CONVENTION DISPLAY-HINT "4x" STATUS current DESCRIPTION "The representation of a BGP Community." SYNTAX OCTET STRING (SIZE(4)) BgpCommunityAction ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "How to handle adding a community attribute." SYNTAX INTEGER { none(0), -- No action is carried out removeAll(1), -- Current community list is cleared removeSpecific(2), -- The community is removed from the list setSpecific(3), -- The community is added to the list removeAllAndSet(4) -- The community replaces the current list } BgpIpMatchType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The type of match carried out by the route map for this IP prefix list." SYNTAX INTEGER { nlriAddr(1), sourceAddr(2), nextHopAddr(3) } BgpAsSize ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The size of the AS number." SYNTAX INTEGER { twoOctet(1), fourOctet(2) } bgpRibManagerTable OBJECT-TYPE SYNTAX SEQUENCE OF BgpRibManagerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents a RIB Manager entity." ::= { rtrBgp 1 } bgpRibManagerEntry OBJECT-TYPE SYNTAX BgpRibManagerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents a RIB Manager entity." INDEX { bgpRibManagerIndex } ::= { bgpRibManagerTable 1 } BgpRibManagerEntry ::= SEQUENCE { bgpRibManagerIndex Unsigned32, bgpRibManagerRowStatus RowStatus, bgpRibManagerLocalAs BgpAutonomousSystemNumber, bgpRibManagerLocalIdentifier BgpIdentifier } bgpRibManagerIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Identifies a RIB Manager entity." ::= { bgpRibManagerEntry 1 } bgpRibManagerRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status for this RIB Manager Entity Table entry, used to create and destroy table entries." ::= { bgpRibManagerEntry 2 } bgpRibManagerLocalAs OBJECT-TYPE SYNTAX BgpAutonomousSystemNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The local autonomous system number. If the bgpAsSize is twoOctet, then the range is constrained to be 0-65535. A non-mappable 4-octet AS number should only be used when all BGP speakers within the AS support 4-octet AS numbers. This field can only be changed when the BGP entity is not active." ::= { bgpRibManagerEntry 3 } bgpRibManagerLocalIdentifier OBJECT-TYPE SYNTAX BgpIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "The BGP Identifier of the local system. This is a generic identifier and not necessarily an IP address. This field can only be changed when the BGP entity is not active." ::= { bgpRibManagerEntry 4 } ------------------------------------------------------------------------------- -- BGP Peer Data Table -- This table contains all the information required for each peer including -- protocol parameters, statistics and policy configuration. A row in this -- table is created for each peer the RIB Manager knows about. bgpPeerTable OBJECT-TYPE SYNTAX SEQUENCE OF BgpPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "BGP peer table. This table contains, one entry per BGP peer, and information about the connections with BGP peers." ::= { rtrBgp 2 } bgpPeerEntry OBJECT-TYPE SYNTAX BgpPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry containing information about the connection with a BGP peer." INDEX { bgpPeerRemoteAddrType, bgpPeerRemoteAddr } ::= { bgpPeerTable 1 } BgpPeerEntry ::= SEQUENCE { bgpPeerRemoteAddrType InetAddressType, bgpPeerRemoteAddr InetAddress, bgpPeerFsmState BgpPeerStates, bgpPeerRowStatus RowStatus, bgpPeerLocalAddrType InetAddressType, bgpPeerLocalAddr InetAddress, bgpPeerRemoteAs BgpAutonomousSystemNumber, bgpPeerLastError OCTET STRING, bgpPeerFsmEstablishedTime Gauge32, bgpPeerHoldTimeConfig Unsigned32, bgpPeerKeepAliveConfig Unsigned32, bgpPeerHoldTime Integer32, bgpPeerKeepAlive Integer32, bgpPeerConfigMaxPrefix Integer32, bgpPeerPassword OCTET STRING, bgpPeerCapabilitySent BgpCapabilities, bgpPeerCapabilityRcv BgpCapabilities, bgpPeerCapabilityNegotiated BgpCapabilities, bgpPeerSelectedLocalAddr InetAddress, bgpPeerSelectedLocalPort InetPortNumber, bgpPeerSelectedRemotePort InetPortNumber, bgpPeerClearCmd INTEGER, bgpPeerDescr SnmpAdminString } bgpPeerRemoteAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address family of the remote end of the peering session." ::= { bgpPeerEntry 1 } bgpPeerRemoteAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address of the remote end of the peering session." ::= { bgpPeerEntry 2 } bgpPeerFsmState OBJECT-TYPE SYNTAX BgpPeerStates MAX-ACCESS read-only STATUS current DESCRIPTION "The BGP peer's FSM state." ::= { bgpPeerEntry 3 } bgpPeerRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object type reflects the status of the row within the agent. An instance of this row is returned by the agent to reflect the validity of the current state of this row." ::= { bgpPeerEntry 4 } bgpPeerLocalAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "The address family of the local end of the peering session." ::= { bgpPeerEntry 5 } bgpPeerLocalAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The address of the local end of the peering session. If a zero length address is used, DC-BGP will not bind a specific address but use whatever is available. In this case the bgpPeerSelectedLocalAddr field shows which local address is actually used. If a specific local address is configured, then outbound socket connections will be bound to this address." ::= { bgpPeerEntry 6 } bgpPeerRemoteAs OBJECT-TYPE SYNTAX BgpAutonomousSystemNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The remote autonomous system number. This field can only be changed when the BGP peer entry is not active." ::= { bgpPeerEntry 7 } bgpPeerLastError OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) MAX-ACCESS read-only STATUS current DESCRIPTION "The last error code and subcode sent or received on this connection. If no error has occurred, this field is zero. Otherwise, the first byte of this two byte OCTET STRING contains the error code, and the second byte contains the subcode." ::= { bgpPeerEntry 8 } bgpPeerFsmEstablishedTime OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This timer indicates how long this peer has been in the Established state or how long since this peer was last in the Established state. It is set to zero when a new peer is configured or the router is booted." ::= { bgpPeerEntry 9 } bgpPeerHoldTimeConfig OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Time interval in seconds for the Hold Time configured for this BGP speaker with this peer. This value is placed in an OPEN message sent to this peer by this BGP speaker, and is compared with the Hold Time field in an OPEN message received from the peer when determining the Hold Time (bgpPeerHoldTime) with the peer. This value must not be less than three seconds if it is not zero (0) in which case the Hold Time is NOT to be established with the peer. The suggested value for this timer is 90 seconds." ::= { bgpPeerEntry 10 } bgpPeerKeepAliveConfig OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Time interval in seconds for the KeepAlive configured for this BGP speaker with this peer. The value of this object will only determine the KEEPALIVE messages' frequency relative to the value specified in bgpPeerHoldTimeConfigd; the actual time interval for the KEEPALIVE messages is indicated by bgpPeerKeepAlive. A reasonable maximum value for this timer would be configured to be one third of that of bgpPeerHoldTimeConfigd. If the value of this object is zero (0), no periodical KEEPALIVE messages are sent to the peer after the BGP connection has been established. The suggested value for this timer is 30 seconds." ::= { bgpPeerEntry 11 } bgpPeerHoldTime OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time interval in seconds for the Hold Timer established with the peer. The value of this is calculated by this BGP speaker by using the smaller of the value in bgpPeerHoldTimeConfigd and the Hold Time received in the OPEN message. This value must be at least three seconds if it is not zero (0) in which case the Hold Timer has not been established with the peer, or, the value of bgpPeerHoldTimeConfigd is zero (0)." ::= { bgpPeerEntry 12 } bgpPeerKeepAlive OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Time interval in seconds for the KeepAlive timer established with the peer. The value of this is calculated by this BGP speaker such that, when compared with bgpPeerHoldTime, it has the same proportion as what bgpPeerKeepAliveConfig has when compared with bgpPeerHoldTimeConfig. If the value of this object is zero (0), it indicates that the KeepAlive timer has not been established with the peer, or, the value of bgpPeerKeepAliveConfig is zero (0)." ::= { bgpPeerEntry 13 } bgpPeerConfigMaxPrefix OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to limit the number of prefixes that can be accepted from this peer. Setting bgpPeerConfigMaxPrfx to a non-zero value sets the maximum number of prefixes (totalled across all supported address families) that can be accepted from this peer." ::= { bgpPeerEntry 14 } bgpPeerPassword OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-create STATUS current DESCRIPTION "The password used by this peer." ::= { bgpPeerEntry 15 } bgpPeerCapabilitySent OBJECT-TYPE SYNTAX BgpCapabilities MAX-ACCESS read-only STATUS current DESCRIPTION "The capabilities announced to the peer on the most recent Open message sent to the peer. This field is set to zero before the first Open message is sent to the peer, and is unchanged if the session comes down." ::= { bgpPeerEntry 16 } bgpPeerCapabilityRcv OBJECT-TYPE SYNTAX BgpCapabilities MAX-ACCESS read-only STATUS current DESCRIPTION "The capabilities received on the most recent Open message received from the peer. This field is set to zero before the first Open message is received from the peer, and is unchanged if the session comes down. In the event that the peer signals a capability that DC-BGP does not recognize, this field will only contain those capabilities that DC-BGP recognizes. A user should walk the bgpPeerCapsRcvdTable to confirm the full list of capabilities received from the peer." ::= { bgpPeerEntry 17 } bgpPeerCapabilityNegotiated OBJECT-TYPE SYNTAX BgpCapabilities MAX-ACCESS read-only STATUS current DESCRIPTION "The capabilities negotiated for the session with the peer. This field is set to zero before Open messages have been exchanged with the peer, and is unchanged if the session comes down." ::= { bgpPeerEntry 18 } bgpPeerSelectedLocalAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The address selected for the local end of the peering session. If a connection exists and bgpPeerLocalAddr is specified then these two fields will be identical." ::= { bgpPeerEntry 19 } bgpPeerSelectedLocalPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The local port selected for transport connection between the BGP peers. A value of zero implies that there is currently no connection to this peer." ::= { bgpPeerEntry 20 } bgpPeerSelectedRemotePort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The remote port selected for the transport connection between the BGP peers. A value of zero implies that there is currently no connection to this peer." ::= { bgpPeerEntry 21 } bgpPeerClearCmd OBJECT-TYPE SYNTAX INTEGER { off (2), on (3), soft (4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Reset action to be performed on BGP session." DEFVAL { off } ::= { bgpPeerEntry 22 } bgpPeerDescr OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used as a varbind in the BGP Traps the value of this object should be the IP address contained in the remote peer 'bgpPeerRemoteAddr'" ::= { bgpPeerEntry 23} -- -- Peer configuration table. -- bgpPeerAfiSafiTable OBJECT-TYPE SYNTAX SEQUENCE OF BgpPeerAfiSafiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Peer configuration table. This table allows a user to configure peer characteristics on a per AFI/SAFI basis. Rows in this table cannot be created or destroyed manually. A table entry for each supported address family is created automatically when an entry in the bgpPeerTable is created. The entries are destroyed when the bgpPeerTable entry is destroyed." ::= { rtrBgp 3 } bgpPeerAfiSafiEntry OBJECT-TYPE SYNTAX BgpPeerAfiSafiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Peer configuration table entry." INDEX { bgpPeerRemoteAddrType, bgpPeerRemoteAddr, bgpPeerAfiSafiAfiType, bgpPeerAfiSafiSafi } ::= { bgpPeerAfiSafiTable 1 } BgpPeerAfiSafiEntry ::= SEQUENCE { bgpPeerAfiSafiAfiType InetAddressType, bgpPeerAfiSafiSafi RtrSafi, bgpPeerAfiSafiStatus INTEGER } bgpPeerAfiSafiAfiType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The AFI index into the peer table." ::= { bgpPeerAfiSafiEntry 1 } bgpPeerAfiSafiSafi OBJECT-TYPE SYNTAX RtrSafi MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SAFI index into the peer table." ::= { bgpPeerAfiSafiEntry 2 } bgpPeerAfiSafiStatus OBJECT-TYPE SYNTAX INTEGER { disable (1), enable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When bgpPeerAfiSafiStatus is 'Disable', BGP will not advertise Multiprotocol support to the peer for this address family. When bgpPeerAfiSafiStatus is 'Enable', BGP will advertise Multiprotocol support to the peer. Any update to this object will take effect the next time that the bgpPeerTable entry is activated (BGP Peer entity activation). Default = disable (1)." ::= { bgpPeerAfiSafiEntry 3 } -- -- BGP Network Layer Reachability Information (NLRI) Data -- -- This table contains per route information including routes, attributes -- and flap statistics if the route is being damped. bgpNlriTable OBJECT-TYPE SYNTAX SEQUENCE OF BgpNlriEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The BGP-4 Received Path Attribute Table contains information about paths to destination networks received from all BGP4 peers. It is equivalent to the bgpM2NlriTable, with additional fields from the bgpM2PathAttrTable, and fields to monitor the Route Flap damping state of the NLRI. This table must contain an identical set of fields to the bgpNlriPrefixTable. All non-index fields must be in the same order in this table and the bgpNlriPrefixTable." ::= { rtrBgp 4 } bgpNlriEntry OBJECT-TYPE SYNTAX BgpNlriEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a path to a network." INDEX { bgpPeerRemoteAddrType, bgpPeerRemoteAddr, bgpNlriAfiType, bgpNlriSafi, bgpNlriPerfixAddress, bgpNlriPrefixLen } ::= { bgpNlriTable 1 } BgpNlriEntry ::= SEQUENCE { bgpNlriAfiType InetAddressType, bgpNlriSafi RtrSafi, bgpNlriPerfixAddress InetAddress, bgpNlriPrefixLen InetAddressPrefixLength, bgpNlriASPathStr OCTET STRING, bgpNlriNextHop InetAddress, bgpNlriAsSize BgpAsSize, bgpNlriPathAttrMultiExitDisc Unsigned32, bgpNlriPathAttrLocalPref Unsigned32, bgpNlriBest TruthValue, bgpNlriPathAttrMEDPrsnt TruthValue } bgpNlriAfiType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address family of the prefix for this NLRI." ::= { bgpNlriEntry 1 } bgpNlriSafi OBJECT-TYPE SYNTAX RtrSafi MAX-ACCESS not-accessible STATUS current DESCRIPTION "The subsequent address family of the prefix for this NLRI." ::= { bgpNlriEntry 2 } bgpNlriPerfixAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "An address prefix in the Network Layer Reachability Information field. This object is an address containing the prefix with length specified by bgpNlriPrfxLen. Any bits beyond the length specified by bgpNlriPrfxLen are zeroed." ::= { bgpNlriEntry 3 } bgpNlriPrefixLen OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS not-accessible STATUS current DESCRIPTION "Length in bits of the IP address prefix in the Network Layer Reachability Information field." ::= { bgpNlriEntry 4 } bgpNlriASPathStr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "This is a string depicting the autonomous system path to this network which was received from the peer which advertised it. If bgpRibManagerAsSize is four-octet and the peer does not support four octet AS numbers this string represents the AS_PATH formed by combining the AS_PATH and AS4_PATH attributes as detailed in RFC 4893. Two-octet AS numbers appear as four-octet numbers by adding two bytes of zero padding. The format of the string is simply the AS_PATH attribute. It can be converted to a more readable format by the management agent." ::= { bgpNlriEntry 5 } bgpNlriNextHop OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The address of the border router that should be used to access the destination network. This address is the nexthop address received in the UPDATE packet. The address family of this object will be the same as that of the prefix in this row." ::= { bgpNlriEntry 6 } bgpNlriAsSize OBJECT-TYPE SYNTAX BgpAsSize MAX-ACCESS read-only STATUS current DESCRIPTION "Whether the bgpNlriASPathStr field contains two or four byte AS numbers." ::= { bgpNlriEntry 7 } bgpNlriPathAttrMultiExitDisc OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This metric is used to discriminate between multiple exit points to an adjacent autonomous system. Valid only if bgpNlriPathAttrMEDPrsnt is TRUE." ::= { bgpNlriEntry 8 } bgpNlriPathAttrLocalPref OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The originating BGP4 speaker's degree of preference for an advertised route." ::= { bgpNlriEntry 9 } bgpNlriBest OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "An indication of whether or not this route was chosen as the best BGP4 route." ::= { bgpNlriEntry 10 } bgpNlriPathAttrMEDPrsnt OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If true, then the route has an associated MED attribute, whose value is given in bgpNlriPathAttrMultiExitDisc. If false, the route has no MED attribute, and the value of bgpNlriPathAttrMultiExitDisc is undefined." ::= { bgpNlriEntry 11 } -- -- BGP Adj-RIB Out Table -- -- This table contains the set of routes advertised to each peer. bgpAdjRibOutTable OBJECT-TYPE SYNTAX SEQUENCE OF BgpAdjRibOutEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The BGP Adjacent Routing Information Base (Adj-RIB-Out) Table contains the set of routes advertised to each peer." ::= { rtrBgp 5 } bgpAdjRibOutEntry OBJECT-TYPE SYNTAX BgpAdjRibOutEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a path to a network that has been advertised to a peer. The route has been explicitly advertised in an UPDATE message sent to the peer." INDEX { bgpPeerRemoteAddrType, bgpPeerRemoteAddr, bgpAdjRibOutAfiType, bgpAdjRibOutSafi, bgpAdjRibOutPrefix, bgpAdjRibOutPrefixLen } ::= { bgpAdjRibOutTable 1 } BgpAdjRibOutEntry ::= SEQUENCE { bgpAdjRibOutAfiType InetAddressType, bgpAdjRibOutSafi RtrSafi, bgpAdjRibOutPrefix InetAddress, bgpAdjRibOutPrefixLen InetAddressPrefixLength, bgpAdjRibOutAdvertStatus INTEGER, bgpAdjRibOutASPathStr OCTET STRING, bgpAdjRibOutNextHop InetAddress, bgpAdjRibOutAsSize BgpAsSize, bgpAdjRibOutMultiExitDisc Unsigned32, bgpAdjRibOutLocalPref Unsigned32, bgpAdjRibOutMEDPrsnt TruthValue } bgpAdjRibOutAfiType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address family of the prefix for this Adj-RIB Out route." ::= { bgpAdjRibOutEntry 1 } bgpAdjRibOutSafi OBJECT-TYPE SYNTAX RtrSafi MAX-ACCESS not-accessible STATUS current DESCRIPTION "The subsequent address family of the prefix for this Adj-RIB Out route." ::= { bgpAdjRibOutEntry 2 } bgpAdjRibOutPrefix OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address prefix of this Adj-RIB Out route. The length is specified by bgpAdjRibOutPrefixLen. Any bits beyond the length specified by bgpAdjRibOutPrefixLen are set to zero." ::= { bgpAdjRibOutEntry 3 } bgpAdjRibOutPrefixLen OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS not-accessible STATUS current DESCRIPTION "Length in bits of the address prefix contained in the bgpAdjRibOutPrefix object." ::= { bgpAdjRibOutEntry 4 } bgpAdjRibOutAdvertStatus OBJECT-TYPE SYNTAX INTEGER { advertised(1), suppressed(2), pendingWithdrawal(3), withdrawn(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current state of advertisement of the route to the peer. A value of advertised(1) indicates that the route has been advertised to the peer. A value of suppressed(2) indicates that the route is not currently advertised to the peer, but will be advertised when a minimum advertisement interval timer expires. A value of pendingWithdrawal(3) indicates that the route is currently advertised to the peer, but will be withdrawn when the timer expires. A value of withdrawn(4) indicates that the route has been withdrawn from the peer, and this entry will be removed from the Adj-RIB-Out on the expiry of the timer." ::= { bgpAdjRibOutEntry 5 } bgpAdjRibOutASPathStr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "This is a string containing the autonomous system path sent to this peer in the AS_PATH attribute for this Adj-RIB-Out route. If this path contains four-octet AS numbers and the peer does not support these a two-octet AS_PATH attribute and associated AS4_PATH attribute will be advertised to the peer instead as detailed in RFC 4893. However, this field will report the four-octet AS_PATH that would have been advertised to the peer if it had supported four-byte AS numbers. Two-octet AS numbers appear as four-octet numbers by adding two bytes of zero padding. The format of the string is simply the AS_PATH attribute. This can be converted to a more readable format by the management agent." ::= { bgpAdjRibOutEntry 6 } bgpAdjRibOutNextHop OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The next hop address transmitted in the UPDATE packet. The address family of this object is the same as that of bgpAdjRibOutPrfx." ::= { bgpAdjRibOutEntry 7 } bgpAdjRibOutAsSize OBJECT-TYPE SYNTAX BgpAsSize MAX-ACCESS read-only STATUS current DESCRIPTION "Whether the bgpAdjRibOutASPathStr object contains two or four byte AS numbers." ::= { bgpAdjRibOutEntry 8} bgpAdjRibOutMultiExitDisc OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This metric is used to discriminate between multiple exit points to an adjacent autonomous system. Valid only if bgpAdjRibOutMEDPrsnt is TRUE." ::= { bgpAdjRibOutEntry 9 } bgpAdjRibOutLocalPref OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The local preference for this Adj-RIB-Out route, as transmitted in the UPDATE message sent to the peer." ::= { bgpAdjRibOutEntry 10 } bgpAdjRibOutMEDPrsnt OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If true, then the route has an associated MED attribute, whose value is given in bgpAdjRibOutMultiExitDisc. If false, the route has no MED attribute, and the value of bgpAdjRibOutMultiExitDisc is undefined." ::= { bgpAdjRibOutEntry 11 } -- -- Network prefix to announce via BGP configuration table. -- bgpNetworkTable OBJECT-TYPE SYNTAX SEQUENCE OF BgpNetworkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Network prefix to announce via BGP configuration table. This table allows a user to configure network prefixes to announce via BGP on a per AFI/SAFI basis." ::= { rtrBgp 6 } bgpNetworkEntry OBJECT-TYPE SYNTAX BgpNetworkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Network prefix to announce via BGP configuration table entry." INDEX { bgpNetworkAfiType, bgpNetworkSafi, bgpNetworkAddrType, bgpNetworkPrefixAddr, bgpNetworkPrefixLen } ::= { bgpNetworkTable 1 } BgpNetworkEntry ::= SEQUENCE { bgpNetworkAfiType InetAddressType, bgpNetworkSafi RtrSafi, bgpNetworkAddrType InetAddressType, bgpNetworkPrefixAddr InetAddress, bgpNetworkPrefixLen Integer32, bgpNetworkRowStatus RowStatus } bgpNetworkAfiType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The AFI index into the network table." ::= { bgpNetworkEntry 1 } bgpNetworkSafi OBJECT-TYPE SYNTAX RtrSafi MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SAFI index into the network table." ::= { bgpNetworkEntry 2 } bgpNetworkAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of the address used as the network prefix." ::= { bgpNetworkEntry 3 } bgpNetworkPrefixAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Destination IP address filter. Do not match the source routing information to this entry if one of these fails: - the destination IP address in the source routing information, with the IP address filter prefix length applied, matches the IP address filter with the IP address filter prefix length applied - the destination IP address prefix length is greater than or equal to the IP address filter prefix length. If the IP address filter prefix length is L, then applying the length to an address means taking the first L bits of the address. To avoid having any destination IP address filtering, set the IP address filter to all zeroes and the IP address filter prefix length to zero." ::= { bgpNetworkEntry 4 } bgpNetworkPrefixLen OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Destination IP address filter prefix length (in bits). Do not match the source routing information to this entry if one of these fails: - the destination IP address in the source routing information, with the IP address filter prefix length applied, matches the IP address filter with the IP address filter prefix length applied - the destination IP address prefix length is greater than or equal to the IP address filter prefix length. If the IP address filter prefix length is L, then applying the length to an address means taking the first L bits of the address. To avoid having any destination IP address filtering, set the IP address filter to all zeroes and the IP address filter prefix length to zero." DEFVAL { 0 } ::= { bgpNetworkEntry 5 } bgpNetworkRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to create and delete a network table entry to announce via BGP." ::= { bgpNetworkEntry 6 } -- ------------------ -- bgpRouteMap -- ------------------ bgpRouteMapTable OBJECT-TYPE SYNTAX SEQUENCE OF BgpRouteMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Policy Rule BGP Table." ::= { rtrBgp 7 } bgpRouteMapEntry OBJECT-TYPE SYNTAX BgpRouteMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "BGP policy route map table (match criteria and set options)" INDEX { bgpRouteMapIndex, bgpRouteMapNumber } ::= { bgpRouteMapTable 1 } BgpRouteMapEntry ::= SEQUENCE { bgpRouteMapIndex Unsigned32, bgpRouteMapNumber Unsigned32, bgpRouteMapType BgpPermitOrDeny, bgpRouteMapMaComm DisplayString, bgpRouteMapSeComm DisplayString, bgpRouteMapSeCommAct BgpCommunityAction, bgpRouteMapSeLocPref Integer32, bgpRouteMapSeLocPrefDef TruthValue, bgpRouteMapSeMed Unsigned32, bgpRouteMapSeMedDef TruthValue, bgpRouteMapSeAsPrependCount Unsigned32, bgpRouteMapSeAsPrependSize BgpAsSize, bgpRouteMapSeAsPrependAsVals OCTET STRING, bgpRouteMapMaPrefixListName SnmpAdminString, bgpRouteMapMaAsExp SnmpAdminString } bgpRouteMapIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4278190079) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of this bgpRouteMapEntry. This is the Index used by Neighbors to reference the Route Map. Route map indexes 0xFFnnnnnn, are reserved for representing ORFs advertised by peers with bgpPeerIdentifier nnnnnn." ::= { bgpRouteMapEntry 1 } bgpRouteMapNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of this bgpRouteMapEntry. This is a number used to reference more than one filter per route map index." ::= { bgpRouteMapEntry 2 } bgpRouteMapType OBJECT-TYPE SYNTAX BgpPermitOrDeny MAX-ACCESS read-only STATUS current DESCRIPTION "The type of route map entry. This is only relevant for policy filtering route maps. It indicates the action which should apply to a route which matches the route map entry. This field is ignored for route maps used for aggregation." DEFVAL { permit } ::= { bgpRouteMapEntry 3 } bgpRouteMapMaComm OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-create STATUS current DESCRIPTION "If not representing one or more ORF entries this contains the regular expression to use when matching elements of the community list for a route. If representing ORF entries then instead of a regular expression this contains a simple comma separated list of communities which are or-ed together when matching. In both cases this is stored here in ASCII format. Communities are matched using new-format decimal notation. For example, the community '0x00120101' should be represented in the string as '18:257'. The string is not NULL-terminated. A NULL string or a ma_comm_exp_len of zero indicates that the field is not in use." ::= { bgpRouteMapEntry 4 } bgpRouteMapSeComm OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-create STATUS current DESCRIPTION "Contains the regular expression used when executing the action defined by bgpRouteMapSeCommAct. Allowed values depend on the value of bgpRouteMapSeCommAct - see the comment for bgpRouteMapSeCommAct." ::= { bgpRouteMapEntry 5 } bgpRouteMapSeCommAct OBJECT-TYPE SYNTAX BgpCommunityAction MAX-ACCESS read-create STATUS current DESCRIPTION "The action to take on the community list if this route map matches the route. Note that if the action is AMB_BGP_SET_SPECIFIC or AMB_BGP_REMOVE_ALL_AND_SET, the field bgpRouteMapSeComm must only contain a string representation of a single specific community value, which will be added to the route. If the action is AMB_BGP_REMOVE_SPECIFIC, then the bgpRouteMapSeComm field must contain a regular expression string that matches the community (or communities) to be removed. The possible action values are: AMB_BGP_NONE - Ignore the value of bgpRouteMapSeComm and do nothing. AMB_BGP_REMOVE_ALL - Ignore the value of bgpRouteMapSeComm and remove all communities from the route. AMB_BGP_REMOVE_SPECIFIC - Remove from the route all communities that match the regular expression in bgpRouteMapSeComm. AMB_BGP_SET_SPECIFIC - Append the community in bgpRouteMapSeComm to the communities list. AMB_BGP_REMOVE_ALL_AND_SET - Remove all communities from the route and replace them with the community in bgpRouteMapSeComm." DEFVAL { none } ::= { bgpRouteMapEntry 6 } bgpRouteMapSeLocPref OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The value to set the Local Pref to if there is a match. This value is only used if bgpRouteMapSeLocPrefDef is TRUE." DEFVAL { 0 } ::= { bgpRouteMapEntry 7 } bgpRouteMapSeLocPrefDef OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Whether or not the value in bgpRouteMapSeLocPref should be used for updating attributes." DEFVAL { false } ::= { bgpRouteMapEntry 8 } bgpRouteMapSeMed OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The value to set the MED to if there is a match. A value of 0 indicates that the MED should be removed. This value is only used if bgpRouteMapSeMedDef is TRUE." DEFVAL { 0 } ::= { bgpRouteMapEntry 9 } bgpRouteMapSeMedDef OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Whether or not the value in bgpRouteMapSeMed should be used for updating attributes." DEFVAL { false } ::= { bgpRouteMapEntry 10 } bgpRouteMapSeAsPrependCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "To prepend AS numbers to the AS-Path, set bgpRouteMapSeAsPrependCount to the count of the AS numbers to prepend, set bgpRouteMapSeAsPrependSize to indicate whether the values are 2 or 4 octet AS numbers and fill in bgpRouteMapSeAsPrependAsVals with the AS numbers themselves. When exporting routes to EBGP, BGP applies the AS-prepend rule before prepending the local AS number as required by the BGP specification. This ensures that the local AS number is always the first AS number in the AS path in this case. This field can only be updated if the row is not active." DEFVAL { 0 } ::= { bgpRouteMapEntry 11 } bgpRouteMapSeAsPrependSize OBJECT-TYPE SYNTAX BgpAsSize MAX-ACCESS read-create STATUS current DESCRIPTION "The size of AS numbers in the field bgpRouteMapSeAsPrependAsVals to prepend to the AS path if there is a match. This field is only used if bgpRouteMapSeAsPrependCount is non-zero. This field can only be updated if the row is not active." DEFVAL { twoOctet } ::= { bgpRouteMapEntry 12 } bgpRouteMapSeAsPrependAsVals OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..127)) MAX-ACCESS read-create STATUS current DESCRIPTION "An array containing the AS numbers to prepend to the AS path if there is a match. The length of each AS number is given by bgpRouteMapSeAsPrependSize. This field is only used if bgpRouteMapSeAsPrependCount is non-zero. The count of AS numbers is given by bgpRouteMapSeAsPrependCount. This field can only be updated if the row is not active." ::= { bgpRouteMapEntry 13 } bgpRouteMapMaPrefixListName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..80)) MAX-ACCESS read-create STATUS current DESCRIPTION "The name of prefix-list profile that includes network prefixes to be matched in a route-map policy rule." ::= { bgpRouteMapEntry 14 } bgpRouteMapMaAsExp OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..127)) MAX-ACCESS read-create STATUS current DESCRIPTION "Contains the regular expression to use when matching the AS-Path for a route. This is stored here in ASCII format. AS numbers are matched as decimal numbers. For example, the AS number '0x0123' should be represented in the regular expression string as '291'. A NULL string indicates that the field is not in use. This field is readable and writeable. The range of valid lengths for this field is 0 - 127. " ::= { bgpRouteMapEntry 15 } -- ------------------ -- bgpIpPre -- ------------------ bgpIpPreTable OBJECT-TYPE SYNTAX SEQUENCE OF BgpIpPreEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Policy Rule BGP IP Prefix Table." ::= { rtrBgp 8 } bgpIpPreEntry OBJECT-TYPE SYNTAX BgpIpPreEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "BGP policy IP prefix table" INDEX { bgpRouteMapIndex, bgpRouteMapNumber, bgpIpPreMatch, bgpIpPreNumber } ::= { bgpIpPreTable 1 } BgpIpPreEntry ::= SEQUENCE { bgpIpPreMatch BgpIpMatchType, bgpIpPreNumber Unsigned32, bgpIpPreAfi InetAddressType, bgpIpPreSafi BgpSafi, bgpIpPreAddr InetAddress, bgpIpPreLen InetAddressPrefixLength, bgpIpPreGe Integer32, bgpIpPreLe Integer32, bgpIpPreType BgpPermitOrDeny } bgpIpPreMatch OBJECT-TYPE SYNTAX BgpIpMatchType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of this bgpIpPreEntry. This decides what match command is used by the route map this list is tied to." ::= { bgpIpPreEntry 1 } bgpIpPreNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of this bgpIpPreEntry. This number is used to reference more than one filter per route map index." ::= { bgpIpPreEntry 2 } bgpIpPreAfi OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "The AFI of the address prefix." DEFVAL { ipv4 } ::= { bgpIpPreEntry 3 } bgpIpPreSafi OBJECT-TYPE SYNTAX BgpSafi MAX-ACCESS read-write STATUS current DESCRIPTION "The SAFI of the address prefix." DEFVAL { unicast } ::= { bgpIpPreEntry 4 } bgpIpPreAddr OBJECT-TYPE SYNTAX InetAddress (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The Address part of the prefix." DEFVAL { '00'h } ::= { bgpIpPreEntry 5 } bgpIpPreLen OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS read-write STATUS current DESCRIPTION "The Length (in bits) part of the prefix (as in the 16 in a 128.128/16 prefix)." DEFVAL { 0 } ::= { bgpIpPreEntry 6 } bgpIpPreGe OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The GE value of the prefix. GE and LE allow the range of the prefix length to be matched on to be varied. The range is assumed to be from ge-value to the address length of the family if only the ge attribute is specified, and from len to le-value if only the le attribute is specified. A specified ge-value and/or le-value must satisfy the following condition: len < ge-value <= le-value <= address length of family." DEFVAL { 0 } ::= { bgpIpPreEntry 7 } bgpIpPreLe OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The LE value of the prefix. GE and LE allow the range of the prefix length to be matched on to be varied. The range is assumed to be from ge-value to the address length of the family if only the ge attribute is specified, and from len to le-value if only the le attribute is specified. A specified ge-value and/or le-value must satisfy the following condition: len < ge-value <= le-value <= address length of family." DEFVAL { 0 } ::= { bgpIpPreEntry 8 } bgpIpPreType OBJECT-TYPE SYNTAX BgpPermitOrDeny MAX-ACCESS read-write STATUS current DESCRIPTION "The type of this prefix. This is only applicable if this prefix is linked to a route map with an ORF association and allows the entry to override the action of the route map. This field is ignored otherwise." DEFVAL { permit } ::= { bgpIpPreEntry 9 } -- ---------------------- -- bgpPolicyBind -- ---------------------- bgpPolicyBindTable OBJECT-TYPE SYNTAX SEQUENCE OF BgpPolicyBindEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "BGP policy profile Bind to BGP peer, AFI, SAFI Entitity." ::= { rtrBgp 9 } bgpPolicyBindEntry OBJECT-TYPE SYNTAX BgpPolicyBindEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry defines BGP policy profile bind to BGP peer, AFI, SAFI entity" INDEX { bgpPeerRemoteAddrType, bgpPeerRemoteAddr, bgpPeerAfiSafiAfiType, bgpPeerAfiSafiSafi, bgpPolicyBindDirection, bgpPolicyBindType, bgpPolicyBindNumber } ::= { bgpPolicyBindTable 1 } BgpPolicyBindEntry ::= SEQUENCE { bgpPolicyBindDirection INTEGER, bgpPolicyBindType INTEGER, bgpPolicyBindNumber INTEGER, bgpPolicyBindName SnmpAdminString (SIZE (1..252)), bgpPolicyBindClearStatisticsCmd INTEGER, bgpPolicyBindRowStatus RowStatus } bgpPolicyBindDirection OBJECT-TYPE SYNTAX INTEGER { inbound (2), outbound (3) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the direction on which the bgp policy works, which may be either inbound (for traffic entering the entity) or outbound (for traffic transmitted out of the entity)." ::= { bgpPolicyBindEntry 1 } bgpPolicyBindType OBJECT-TYPE SYNTAX INTEGER { bgpPrefixListIpv4 (2), bgpPrefixListIpv6 (3), bgpRouteMap (4) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "BGP policy profile type." ::= { bgpPolicyBindEntry 2 } bgpPolicyBindNumber OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of this bgp policy profile. This is a number used to reference more than one bgp policy profile per same peer-afi-safi-direction-type entity." ::= { bgpPolicyBindEntry 3 } bgpPolicyBindName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..252)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the name of BGP policy profile bound to this entity." ::= { bgpPolicyBindEntry 4 } bgpPolicyBindClearStatisticsCmd OBJECT-TYPE SYNTAX INTEGER { off (1), on (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Clear statistics command. All Matches counters (of all policy rules) of policy profile bound to entity are cleared." ::= { bgpPolicyBindEntry 5} bgpPolicyBindRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Create or delete BGP policy profile bind to entity" ::= { bgpPolicyBindEntry 6} -- ---------------------- -- bgpPolicyRuleStats -- ---------------------- bgpPolicyRuleStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF BgpPolicyRuleStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Statistics table" ::= { rtrBgp 10 } bgpPolicyRuleStatsEntry OBJECT-TYPE SYNTAX BgpPolicyRuleStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Statistics entry" INDEX { bgpPeerRemoteAddrType, bgpPeerRemoteAddr, bgpPeerAfiSafiAfiType, bgpPeerAfiSafiSafi, bgpPolicyBindDirection, bgpPolicyBindType, bgpPolicyBindNumber, bgpRouteMapIndex, bgpRouteMapNumber } ::= { bgpPolicyRuleStatsTable 1 } BgpPolicyRuleStatsEntry ::= SEQUENCE { bgpPolicyRuleStatsMatches Gauge32, bgpPolicyRuleStatsClearCmd INTEGER } bgpPolicyRuleStatsMatches OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Counts the number of packets that matched a policy rule which is bound to specific peer, address family (afi) and sub address family (safi) with direction and type." ::= { bgpPolicyRuleStatsEntry 1 } bgpPolicyRuleStatsClearCmd OBJECT-TYPE SYNTAX INTEGER { off (1), on (2), softClear (3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Clear statistics command. Rule Matches counter (bgpPolicyRuleStatsMatches) is cleared. Soft Clear option (3) is to update Policy without BGP session re-establishment." ::= { bgpPolicyRuleStatsEntry 2} -- ----------------------------------------------------------------------------- -- Path Attribute Extensions -- ----------------------------------------------------------------------------- bgpPathAttrExtensions OBJECT IDENTIFIER ::= { rtrBgp 11 } -- -------------------------------------------------------------------------------- -- BGP Communities -- This table holds information on the communities the indexed route belongs to. -- -------------------------------------------------------------------------------- bgpPathAttrCommTable OBJECT-TYPE -- FAMILY-SHORT-NAME BGP_CMM SYNTAX SEQUENCE OF BgpPathAttrCommEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The BGP-4 Path Attribute Community Table contains the per network path (NLRI) data on the community membership advertised with a route. The absence of row data for a given network path indicates a lack of this attribute information for the indicated network path." ::= { bgpPathAttrExtensions 1 } bgpPathAttrCommEntry OBJECT-TYPE SYNTAX BgpPathAttrCommEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a community association provided with a path to a network." INDEX { bgpPeerRemoteAddrType, bgpPeerRemoteAddr, bgpNlriAfiType, bgpNlriSafi, bgpNlriPerfixAddress, bgpNlriPrefixLen, bgpPathAttrCommIndex } ::= { bgpPathAttrCommTable 1 } BgpPathAttrCommEntry ::= SEQUENCE { bgpPathAttrCommIndex Unsigned32, bgpPathAttrCommValue BgpCommunity } bgpPathAttrCommIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "An integer index for a row in this table." ::= { bgpPathAttrCommEntry 1 } bgpPathAttrCommValue OBJECT-TYPE SYNTAX BgpCommunity MAX-ACCESS read-only STATUS current DESCRIPTION "A value representing a community. There are certain 4-octet long values which could be returned in this columnar row data that carry additional semantics." ::= { bgpPathAttrCommEntry 2 } -- Traps bgpSessionFailure NOTIFICATION-TYPE OBJECTS { alarmEventLogSourceName, alarmEventLogAlarmOrEventId, alarmEventLogDescription, alarmEventLogSeverity, alarmEventLogDateAndTime, alarmEventReason, bgpPeerDescr, rtrConfigRoutingName } STATUS current DESCRIPTION "The trap is sent when the BGP session fail." ::= { radSysRtrEvents 3 } bgpTcpSessionAuthFailure NOTIFICATION-TYPE OBJECTS { alarmEventLogSourceName, alarmEventLogAlarmOrEventId, alarmEventLogDescription, alarmEventLogSeverity, alarmEventLogDateAndTime, alarmEventReason, bgpPeerDescr, rtrConfigRoutingName } STATUS current DESCRIPTION "The trap is sent when BGP TCP session authentication fail." ::= { radSysRtrEvents 4 } bgpSessionPrefixOverflow NOTIFICATION-TYPE OBJECTS { alarmEventLogSourceName, alarmEventLogAlarmOrEventId, alarmEventLogDescription, alarmEventLogSeverity, alarmEventLogDateAndTime, alarmEventReason, bgpPeerDescr, rtrConfigRoutingName } STATUS current DESCRIPTION "The trap is sent when BGP session received prefix list reached 90% of its maximum ." ::= { radSysRtrEvents 5 } END