SWITCHING-MIB DEFINITIONS ::= BEGIN -- Quanta Switching MIB -- Copyright 2004- Quanta Computer, Inc. All rights reserved. -- This SNMP Management Information Specification -- embodies Quanta Computer Inc.'s confidential and proprietary -- intellectual property. Quanta Computer Inc. retains all title -- and ownership in the Specification including any revisions. -- This Specification is supplied "AS IS", Quanta Computer Inc. -- makes no warranty, either expressed or implied, -- as to the use, operation, condition, or performance of the -- Specification. IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, IpAddress, Integer32, Unsigned32, Counter32, Gauge32, TimeTicks FROM SNMPv2-SMI RowStatus, TruthValue, MacAddress, DateAndTime, TEXTUAL-CONVENTION FROM SNMPv2-TC switch, AgentPortMask FROM QUANTA-SWITCH-MIB DisplayString, PhysAddress FROM RFC1213-MIB VlanId, VlanIndex, dot1qVlanIndex, dot1qFdbId FROM Q-BRIDGE-MIB IANAifType FROM IANAifType-MIB InterfaceIndex, ifIndex, InterfaceIndexOrZero FROM IF-MIB InetAddressType, InetAddress FROM INET-ADDRESS-MIB Ipv6Address, Ipv6AddressPrefix FROM IPV6-TC; switching MODULE-IDENTITY LAST-UPDATED "201108310000Z" -- 26 Jan 2011 12:00:00 GMT ORGANIZATION "QCT" CONTACT-INFO "QCT LLC 47709 Fremont Boulevard, Fremont, CA 94538 TOLL FREE: 855-QCT-MUST Tel: +1 510-270-6111 FAX: +1 510-270-6161 WEB: www.QuantaQCT.com" DESCRIPTION "The QCI Private MIB for Switching" ::= { switch 1 } PortList ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'." SYNTAX OCTET STRING VlanList ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 1 through 8, the second octet specifying vlans 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered vlan, and the least significant bit represents the highest numbered vlan. Thus, each vlan supported is represented by a single bit within the value of this object. If that bit has a value of '1' then the associated port is in that vlan; the port is not included if the vlans bit has a value of '0'." SYNTAX OCTET STRING -- Ipv6Address ::= TEXTUAL-CONVENTION -- DISPLAY-HINT "2x:" -- STATUS current -- DESCRIPTION -- "This data type is used to model IPv6 addresses. -- This is a binary string of 16 octets in network -- byte-order." -- SYNTAX OCTET STRING (SIZE (16)) -- -- Ipv6AddressPrefix ::= TEXTUAL-CONVENTION -- DISPLAY-HINT "2x:" -- STATUS current -- DESCRIPTION -- "This data type is used to model IPv6 address -- prefixes. This is a binary string of up to 16 -- octets in network byte-order." -- SYNTAX OCTET STRING (SIZE (0..16)) -- -- Ipv6AddressIfIdentifier ::= TEXTUAL-CONVENTION -- DISPLAY-HINT "2x:" -- STATUS current -- DESCRIPTION -- "This data type is used to model IPv6 address -- interface identifiers. This is a binary string -- of up to 8 octets in network byte-order." -- SYNTAX OCTET STRING (SIZE (0..8)) -- -- Ipv6IfIndex ::= TEXTUAL-CONVENTION -- DISPLAY-HINT "d" -- STATUS current -- DESCRIPTION -- "A unique value, greater than zero for each -- internetwork-layer interface in the managed -- system. It is recommended that values are assigned -- contiguously starting from 1. The value for each -- internetwork-layer interface must remain constant -- at least from one re-initialization of the entity's -- network management system to the next -- -- -- -- -- re-initialization." -- SYNTAX Integer32 (1..2147483647) -- -- Ipv6IfIndexOrZero ::= TEXTUAL-CONVENTION -- DISPLAY-HINT "d" -- STATUS current -- DESCRIPTION -- "This textual convention is an extension of the -- Ipv6IfIndex convention. The latter defines -- a greater than zero value used to identify an IPv6 -- interface in the managed system. This extension -- permits the additional value of zero. The value -- zero is object-specific and must therefore be -- defined as part of the description of any object -- which uses this syntax. Examples of the usage of -- zero might include situations where interface was -- unknown, or when none or all interfaces need to be -- referenced." -- SYNTAX Integer32 (0..2147483647) --************************************************************************************** -- agentInfoGroup --************************************************************************************** agentInfoGroup OBJECT IDENTIFIER ::= { switching 1 } --************************************************************************************** -- agentInventoryGroup -- --************************************************************************************** agentInventoryGroup OBJECT IDENTIFIER ::= { agentInfoGroup 1 } agentInventorySysDescription OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Inventory system description. " ::= { agentInventoryGroup 1 } agentInventoryMachineType OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Type of the Machine used in the Switch " ::= { agentInventoryGroup 2 } agentInventoryMachineModel OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Machine Model. " ::= { agentInventoryGroup 3 } agentInventorySerialNumber OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Serial number of the switch." ::= { agentInventoryGroup 4 } agentInventoryFRUNumber OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "FRU Number of the switch" ::= { agentInventoryGroup 5 } agentInventoryMaintenanceLevel OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Inventory Maintenance Level" ::= { agentInventoryGroup 6 } agentInventoryPartNumber OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Inventory Part Number" ::= { agentInventoryGroup 7 } agentInventoryHardwareVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Lists the version of hardware of this unit. This is a platform dependant string." ::= { agentInventoryGroup 8 } agentInventoryBurnedInMacAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Burned-In MAC Address" ::= { agentInventoryGroup 9 } agentInventoryOperatingSystem OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Operating System running on this unit" ::= { agentInventoryGroup 10 } agentInventoryNetworkProcessingDevice OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Network Processing Device for this unit" ::= { agentInventoryGroup 11 } agentInventoryAdditionalPackages OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Lists additional functional packages available on this unit." ::= { agentInventoryGroup 12 } agentInventorySoftwareVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Lists the version of software loaded on this unit." ::= { agentInventoryGroup 13 } agentInventoryManufacturer OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Name of the Manufacturer of this unit" ::= { agentInventoryGroup 14 } --************************************************************************************** -- agentTrapLogGroup -- --************************************************************************************** agentTrapLogGroup OBJECT IDENTIFIER ::= { agentInfoGroup 2} agentTrapLogTotal OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of traps sent since last reset." ::= { agentTrapLogGroup 1 } agentTrapLogTotalSinceLastViewed OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of traps sent since last viewed." ::= { agentTrapLogGroup 3 } --************************************************************************************** -- agentTrapLogTable agentTrapLogTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentTrapLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Agent Trap Log" ::= { agentTrapLogGroup 4 } agentTrapLogEntry OBJECT-TYPE SYNTAX AgentTrapLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Agent trap log entry" INDEX { agentTrapLogIndex } ::= { agentTrapLogTable 1 } AgentTrapLogEntry ::= SEQUENCE { agentTrapLogIndex Integer32, agentTrapLogSystemTime DisplayString, agentTrapLogTrap DisplayString } agentTrapLogIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "Unique index of trap entry" ::= { agentTrapLogEntry 1 } agentTrapLogSystemTime OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "System uptime when trap was sent. This entry shows how long the system has been up when the trap occurred." ::= { agentTrapLogEntry 2 } agentTrapLogTrap OBJECT-TYPE SYNTAX DisplayString (SIZE (0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "Description of the trap sent." ::= { agentTrapLogEntry 3 } --************************************************************************************** -- agentSupportedMibTable --************************************************************************************** agentSupportedMibTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSupportedMibEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Supported MIB table" ::= { agentInfoGroup 3 } agentSupportedMibEntry OBJECT-TYPE SYNTAX AgentSupportedMibEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Supported MIB entry" INDEX { agentSupportedMibIndex } ::= { agentSupportedMibTable 1 } AgentSupportedMibEntry ::= SEQUENCE { agentSupportedMibIndex Integer32, agentSupportedMibName DisplayString, agentSupportedMibDescription DisplayString } agentSupportedMibIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "Unique index of the Supported MIB entry" ::= { agentSupportedMibEntry 1 } agentSupportedMibName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the MIB (RFC or IEEE) that is supported." ::= { agentSupportedMibEntry 2 } agentSupportedMibDescription OBJECT-TYPE SYNTAX DisplayString (SIZE (0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "Description of the MIB (RFC or IEEE) that is supported." ::= { agentSupportedMibEntry 3 } --************************************************************************************** -- agentPortStatsRateGroup --************************************************************************************** agentPortStatsRateGroup OBJECT IDENTIFIER ::= { agentInfoGroup 8 } agentPortStatsRateTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentPortStatsRateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" ::= { agentPortStatsRateGroup 1 } agentPortStatsRateEntry OBJECT-TYPE SYNTAX AgentPortStatsRateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { ifIndex } ::= { agentPortStatsRateTable 1 } AgentPortStatsRateEntry ::= SEQUENCE { -- agentPortStatsRateBitsPerSecondRx -- Counter32, -- agentPortStatsRateBitsPerSecondTx -- Counter32, -- agentPortStatsRatePacketsPerSecondRx -- Counter32, -- agentPortStatsRatePacketsPerSecondTx -- Counter32, -- agentPortStatsRateOverflowBitsPerSecondRx -- Counter32, -- agentPortStatsRateOverflowBitsPerSecondTx -- Counter32, -- agentPortStatsRateOverflowPacketsPerSecondRx -- Counter32, -- agentPortStatsRateOverflowPacketsPerSecondTx -- Counter32, agentPortStatsRateHCBitsPerSecondRx Counter64, agentPortStatsRateHCBitsPerSecondTx Counter64, agentPortStatsRateHCPacketsPerSecondRx Counter64, agentPortStatsRateHCPacketsPerSecondTx Counter64 } -- agentPortStatsRateBitsPerSecondRx OBJECT-TYPE -- SYNTAX Counter32 -- UNITS "bits" -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The number of bits per second received. -- This value is an exponentially weighted average and is affected by the -- configured agentPortLoadStatsInterval." -- ::= { agentPortStatsRateEntry 1 } -- -- agentPortStatsRateBitsPerSecondTx OBJECT-TYPE -- SYNTAX Counter32 -- UNITS "bits" -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The number of bits per second transmitted. -- This value is an exponentially weighted average and is affected by the -- configured agentPortLoadStatsInterval." -- ::= { agentPortStatsRateEntry 2 } -- -- agentPortStatsRatePacketsPerSecondRx OBJECT-TYPE -- SYNTAX Counter32 -- UNITS "packets" -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The number of packets per second received. -- This value is an exponentially weighted average and is affected by the -- configured agentPortLoadStatsInterval." -- ::= { agentPortStatsRateEntry 3 } -- -- agentPortStatsRatePacketsPerSecondTx OBJECT-TYPE -- SYNTAX Counter32 -- UNITS "packets" -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The number of packets per second transmitted. -- This value is an exponentially weighted average and is affected by the -- configured agentPortLoadStatsInterval." -- ::= { agentPortStatsRateEntry 4 } -- -- -- agentPortStatsRateOverflowBitsPerSecondRx OBJECT-TYPE -- SYNTAX Counter32 -- UNITS "bits" -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The counter in which stored the number of times -- the associated agentPortStatsRateBitsPerSecondRx counter -- has overflowed." -- ::= { agentPortStatsRateEntry 5 } -- -- agentPortStatsRateOverflowBitsPerSecondTx OBJECT-TYPE -- SYNTAX Counter32 -- UNITS "bits" -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The counter in which stored the number of times -- the associated agentPortStatsRateBitsPerSecondTx counter -- has overflowed." -- ::= { agentPortStatsRateEntry 6 } -- -- agentPortStatsRateOverflowPacketsPerSecondRx OBJECT-TYPE -- SYNTAX Counter32 -- UNITS "packets" -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The counter in which stored the number of times -- the associated agentPortStatsRatePacketsPerSecondRx counter -- has overflowed." -- ::= { agentPortStatsRateEntry 7 } -- -- agentPortStatsRateOverflowPacketsPerSecondTx OBJECT-TYPE -- SYNTAX Counter32 -- UNITS "packets" -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The counter in which stored the number of times -- the associated agentPortStatsRatePacketsPerSecondTx counter -- has overflowed." -- ::= { agentPortStatsRateEntry 8 } agentPortStatsRateHCBitsPerSecondRx OBJECT-TYPE SYNTAX Counter64 UNITS "bits" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bits per second received. This value is an exponentially weighted average and is affected by the configured agentPortLoadStatsInterval." ::= { agentPortStatsRateEntry 9 } agentPortStatsRateHCBitsPerSecondTx OBJECT-TYPE SYNTAX Counter64 UNITS "bits" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bits per second transmitted. This value is an exponentially weighted average and is affected by the configured agentPortLoadStatsInterval." ::= { agentPortStatsRateEntry 10 } agentPortStatsRateHCPacketsPerSecondRx OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets per second received. This value is an exponentially weighted average and is affected by the configured agentPortLoadStatsInterval." ::= { agentPortStatsRateEntry 11 } agentPortStatsRateHCPacketsPerSecondTx OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets per second transmitted. This value is an exponentially weighted average and is affected by the configured agentPortLoadStatsInterval." ::= { agentPortStatsRateEntry 12 } --************************************************************************************** -- agentSwitchCpuProcessGroup -> contains MIB objects displaying various values used in Processfer --allocations -- --************************************************************************************** agentSwitchCpuProcessGroup OBJECT IDENTIFIER ::= { agentInfoGroup 4 } agentSwitchCpuProcessMemFree OBJECT-TYPE SYNTAX Integer32 (0..2147483647) UNITS "KBytes" MAX-ACCESS read-only STATUS current DESCRIPTION " The total memory free for utilization in KBytes." ::= { agentSwitchCpuProcessGroup 1 } agentSwitchCpuProcessMemAvailable OBJECT-TYPE SYNTAX Integer32 (0..2147483647) UNITS "KBytes" MAX-ACCESS read-only STATUS current DESCRIPTION " The total memory available in KBytes." DEFVAL { 2 } ::= { agentSwitchCpuProcessGroup 2 } agentSwitchCpuProcessRisingThreshold OBJECT-TYPE SYNTAX Unsigned32(0..100) MAX-ACCESS read-write STATUS current DESCRIPTION "The CPU Rising utilization threshold in percentage. A zero percent threshold indicates CPU Utilization Notification feature is disabled. A notification is triggered when the total CPU utilization exceeds this threshold over the configured Rising threshold interval. If the Rising threshold is configured to be less than the Falling threshold, the Falling threshold is set equal to the Rising threshold." DEFVAL { 0 } ::= { agentSwitchCpuProcessGroup 3 } agentSwitchCpuProcessRisingThresholdInterval OBJECT-TYPE SYNTAX Unsigned32(0|5..86400) MAX-ACCESS read-write STATUS current DESCRIPTION "The CPU Rising threshold interval in seconds. The time interval is configured in multiples of 5 seconds. A zero Rising interval indicates CPU Utilization Notification feature is disabled." ::= { agentSwitchCpuProcessGroup 4 } agentSwitchCpuProcessFallingThreshold OBJECT-TYPE SYNTAX Unsigned32(0..100) MAX-ACCESS read-write STATUS current DESCRIPTION "The CPU Falling utilization threshold in percentage. Configuration of this object value is optional. Value '0' is not allowed for configuration, if the Rising threshold is non-zero. If the Falling threshold is configured to be greater than the Rising threshold, the Rising threshold is set equal to the Falling threshold. If the Falling threshold is not configured, it takes the same value as the Rising threshold. A notification is triggered when the total CPU utilization falls below this threshold over the configured Falling threshold interval." DEFVAL { 0 } ::= { agentSwitchCpuProcessGroup 5 } agentSwitchCpuProcessFallingThresholdInterval OBJECT-TYPE SYNTAX Unsigned32(0|5..86400) MAX-ACCESS read-write STATUS current DESCRIPTION "The CPU Falling threshold interval in seconds. Configuration of this object value is optional. Value '0' is not allowed for configuration, if the Rising interval is non-zero. If the Falling interval is not configured, it takes the same value as the Rising interval. The time interval is configured in multiples of 5 seconds." ::= { agentSwitchCpuProcessGroup 6 } agentSwitchCpuProcessFreeMemoryThreshold OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The CPU Free Memory threshold in kilobytes. A zero threshold value indicates the CPU Free Memory Notification feature is disabled. Notifications are triggered when the CPU Free Memory falls below the configured threshold and when it rises to 10% above the configured threshold." DEFVAL { 0 } ::= { agentSwitchCpuProcessGroup 7 } --************************************************************************************** -- agentSwitchCpuProcessTable agentSwitchCpuProcessTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchCpuProcessEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A table of Task and cpu utilization." ::= { agentSwitchCpuProcessGroup 8 } agentSwitchCpuProcessEntry OBJECT-TYPE SYNTAX AgentSwitchCpuProcessEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents entry for a Task Table." INDEX { agentSwitchCpuProcessIndex } ::= { agentSwitchCpuProcessTable 1 } AgentSwitchCpuProcessEntry ::= SEQUENCE { agentSwitchCpuProcessIndex Integer32, agentSwitchCpuProcessName DisplayString, agentSwitchCpuProcessPercentageUtilization DisplayString, agentSwitchCpuProcessId DisplayString } agentSwitchCpuProcessIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Unique index of process table" ::= { agentSwitchCpuProcessEntry 1 } agentSwitchCpuProcessName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Name of the process" ::= { agentSwitchCpuProcessEntry 2 } agentSwitchCpuProcessPercentageUtilization OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "CPU utilization per task in Percentage over a period of 5, 60, 300 seconds, and the Rising threshold period also in seconds, if configured." ::= { agentSwitchCpuProcessEntry 3 } agentSwitchCpuProcessId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Process ID" ::= { agentSwitchCpuProcessEntry 4 } --************************************************************************************** -- agentSwitchCpuProcessTotalUtilization agentSwitchCpuProcessTotalUtilization OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Total CPU utilization over a period of 5, 60, 300 seconds, and the Rising threshold period also in seconds, if configured." ::= { agentSwitchCpuProcessGroup 9 } --************************************************************************************** -- agentConfigGroup -- --************************************************************************************** agentConfigGroup OBJECT IDENTIFIER ::= { switching 2 } agentCLIConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 1 } --************************************************************************************** -- agentLoginSessionTable -- --************************************************************************************** agentLoginSessionTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentLoginSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the switch's login session" ::= { agentCLIConfigGroup 1 } agentLoginSessionEntry OBJECT-TYPE SYNTAX AgentLoginSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Login Session Entry" INDEX { agentLoginSessionIndex } ::= { agentLoginSessionTable 1 } AgentLoginSessionEntry ::= SEQUENCE { agentLoginSessionIndex Integer32, agentLoginSessionUserName DisplayString, -- agentLoginSessionIPAddress -- IpAddress, agentLoginSessionConnectionType INTEGER, agentLoginSessionIdleTime TimeTicks, agentLoginSessionSessionTime TimeTicks, agentLoginSessionStatus RowStatus, agentLoginSessionInetAddressType InetAddressType, agentLoginSessionInetAddress InetAddress } agentLoginSessionIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "Agent Login Session Index of the switch" ::= { agentLoginSessionEntry 1 } agentLoginSessionUserName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Agent Login Session UserName of the switch" ::= { agentLoginSessionEntry 2 } -- agentLoginSessionIPAddress OBJECT-TYPE -- SYNTAX IpAddress -- MAX-ACCESS read-only -- STATUS obsolete -- DESCRIPTION -- "Agent Login Session IP Address of the switch" -- ::= { agentLoginSessionEntry 3 } agentLoginSessionConnectionType OBJECT-TYPE SYNTAX INTEGER { unknown(0), serial(1), telnet(2), ssh(3), http(4), https(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Agent Login Session Connection Type of the switch" ::= { agentLoginSessionEntry 4 } agentLoginSessionIdleTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Agent Login Session Idle Time of the switch" ::= { agentLoginSessionEntry 5 } agentLoginSessionSessionTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Agent Login Session Time of the switch" ::= { agentLoginSessionEntry 6 } agentLoginSessionStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Status of the user. active(1) - This connection is active. destroy(6) - Set to this value to disconnect this user." ::= { agentLoginSessionEntry 7 } agentLoginSessionInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "Type of address agentLoginSessionInetAddress is returning. Can be either unknown(0), ipv4(1), or ipv6 (2). Will return unknown(0) in the case of a serial login." ::= { agentLoginSessionEntry 8 } agentLoginSessionInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Inet Address of the connecting the user is logging in with. Will return a zero-length string in the case of a serial login." ::= { agentLoginSessionEntry 9 } --************************************************************************************** -- agentTelnetConfigGroup -- --************************************************************************************** agentTelnetConfigGroup OBJECT IDENTIFIER ::= { agentCLIConfigGroup 2 } agentTelnetLoginTimeout OBJECT-TYPE SYNTAX Integer32 (1..160) MAX-ACCESS read-write STATUS current DESCRIPTION "Telnet login timeout (minutes) Config telnet timeout will set the telnet session timeout value. A session is active as long as the session has not remained idle for the value set. Specify a value from 1 to 160. Note: Changing the timeout value for active sessions does not become effective until the session is reaccessed. Any keystroke will also activate the new timeout duration." ::= { agentTelnetConfigGroup 1 } agentTelnetMaxSessions OBJECT-TYPE SYNTAX Integer32 (0..5) MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum number of Telnet Sessions Config telnet maxsessions is an integer value from 0 to 5 that specifies the maximum number of telnet sessions that can be established. If the value is 0, no Telnet session can be established. " ::= { agentTelnetConfigGroup 2 } agentTelnetAllowNewMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Allow new telnet sessions (enable or disable) Config telnet disable means that no new Telnet sessions are to be established. Any already established session remains active until the session is ended or an abnormal network error ends it. " ::= { agentTelnetConfigGroup 3 } --************************************************************************************** -- agentUserConfigGroup -- --************************************************************************************** agentUserConfigGroup OBJECT IDENTIFIER ::= { agentCLIConfigGroup 3 } agentUserConfigCreate OBJECT-TYPE SYNTAX DisplayString (SIZE(1..8)) MAX-ACCESS read-write STATUS current DESCRIPTION "Create a new user. When set with a non-empty string, a new user with that name will be created. This object will only return an empty string. This string is limited to alpha-numeric strings (uncluding the '-' and '_' characters)." ::= { agentUserConfigGroup 1 } --************************************************************************************** agentUserConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentUserConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "User Config Table" ::= { agentUserConfigGroup 2 } agentUserConfigEntry OBJECT-TYPE SYNTAX AgentUserConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "User Config Entry" INDEX { agentUserIndex } ::= { agentUserConfigTable 1 } AgentUserConfigEntry ::= SEQUENCE { agentUserIndex Integer32, agentUserName DisplayString, agentUserPassword DisplayString, agentUserAccessMode INTEGER, agentUserStatus RowStatus, agentUserAuthenticationType INTEGER, agentUserEncryptionType INTEGER, agentUserEncryptionPassword DisplayString, agentUserLockoutStatus INTEGER, agentUserPasswordExpireTime DateAndTime, agentUserSnmpv3AccessMode INTEGER, agentUserPrivilegeLevel Integer32 } agentUserIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Agent User Config Index" ::= { agentUserConfigEntry 1 } agentUserName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "Agent User Name. This string is limited to alpha-numeric strings (including the '-' and '_' characters)." ::= { agentUserConfigEntry 2 } agentUserPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(8..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "Agent User Password This object will return an empty string even if a password is set." ::= { agentUserConfigEntry 3 } agentUserAccessMode OBJECT-TYPE SYNTAX INTEGER { suspended(0), read(1), write(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Agent User Access Mode, access level 0 for Read Acecess(WEB suspended)" ::= { agentUserConfigEntry 4 } agentUserStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Agent User Status. active(1) - This user account is active. destroy(6) - Set to this value to remove this user account." ::= { agentUserConfigEntry 5 } agentUserAuthenticationType OBJECT-TYPE SYNTAX INTEGER { none(1), hmacmd5(2), hmacsha(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 User Authentication. The user passsword must be set to a string greater than or equal to 8 characters for this to be set to anything but none(1). none(1) - no authentication used hmacmd5(2) - Use HMAC-MD5 authentication hmacsha(3) - Use HMAC-SHA authentication" ::= { agentUserConfigEntry 6 } agentUserEncryptionType OBJECT-TYPE SYNTAX INTEGER { none(1), des(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 User Encryption Can not be set to des(2) if agentUserAuthenticationType is set to none(1). none(1) - no encryption used des(2) - DES encryption used" ::= { agentUserConfigEntry 7 } agentUserEncryptionPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(8..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 User Encryption Password This object will return an empty string even if a password is set. agentUserEncryptionType must be set to des(2) before this object can be configured. This object will return an empty string even if a password is set." ::= { agentUserConfigEntry 8 } agentUserLockoutStatus OBJECT-TYPE SYNTAX INTEGER { false(0), true(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Displays whether the user account is locked due to excessive failed login attempts." ::= { agentUserConfigEntry 9 } agentUserPasswordExpireTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "Date and time when the user's password expires (past or present). Only valid when password aging is enabled." ::= { agentUserConfigEntry 10 } agentUserSnmpv3AccessMode OBJECT-TYPE SYNTAX INTEGER { read(1), write(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "SNMPv3 Access Mode read(1) - read-only write(2) - read-write" ::= { agentUserConfigEntry 11 } agentUserPrivilegeLevel OBJECT-TYPE SYNTAX Integer32 (0..1|15) MAX-ACCESS read-write STATUS current DESCRIPTION "Agent User Privilege Level 0 suspended(web login), 1 read-only, 15 read-write." ::= { agentUserConfigEntry 12 } --************************************************************************************** -- agentSerialGroup -- --************************************************************************************** agentSerialGroup OBJECT IDENTIFIER ::= { agentCLIConfigGroup 5 } agentSerialTimeout OBJECT-TYPE SYNTAX Integer32 (0..160) MAX-ACCESS read-write STATUS current DESCRIPTION "agentSerialTimeout specifies the maximum connect time(in minutes) without console activity. A value of 0 indicates that a console can be connected indefinitely. The time range is 0 to 160. " ::= { agentSerialGroup 1 } agentSerialBaudrate OBJECT-TYPE SYNTAX INTEGER { baud-1200(1), baud-2400(2), baud-4800(3), baud-9600(4), baud-19200(5), baud-38400(6), baud-57600(7), baud-115200(8) } MAX-ACCESS read-write STATUS current DESCRIPTION " agentSerialBaudrate specifies the current baud rate at which the serial port will try to connect. The available values are 1200, 2400, 4800, 9600, 19200, 38400,57600, and 115200 baud. " ::= { agentSerialGroup 2 } agentSerialCharacterSize OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "agentSerialCharacterSize specifies the number of bits in a character. The number of bits is always 8." ::= { agentSerialGroup 3 } agentSerialHWFlowControlMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "agentSerialHardwareFlowControl specifies whether hardware flow-control is enabled or disabled. Hardware Flow Control is always disabled." ::= { agentSerialGroup 4 } agentSerialStopBits OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION " agentSerialStopBits specifies the number of Stop bits per character. The number of Stop bits is always 1." ::= { agentSerialGroup 5 } agentSerialParityType OBJECT-TYPE SYNTAX INTEGER { even(1), odd(2), none(3) } MAX-ACCESS read-only STATUS current DESCRIPTION " agentSerialParityType specifies the Parity Method used on the Serial Port. The Parity Method is always None. " ::= { agentSerialGroup 6 } agentSerialTerminalLength OBJECT-TYPE SYNTAX Integer32 (10..100) MAX-ACCESS read-write STATUS current DESCRIPTION " agentSerialTerminalLength specifies the height of words in terminal screen." ::= { agentSerialGroup 7 } --************************************************************************************** -- agentPasswordManagementConfigGroup -- --************************************************************************************** agentPasswordManagementConfigGroup OBJECT IDENTIFIER ::= { agentCLIConfigGroup 6 } agentPasswordManagementMinLength OBJECT-TYPE SYNTAX Integer32 (0 | 8..64) MAX-ACCESS read-write STATUS current DESCRIPTION "Minimum length for user passwords All new local user passwords must be at least this many characters in length. " ::= { agentPasswordManagementConfigGroup 1 } agentPasswordManagementHistory OBJECT-TYPE SYNTAX Integer32 (0..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of previous passwords to store for prevention of password reuse. This ensures that each user does not reuse passwords often. A value of 0 indicates that no previous passwords will be stored. " ::= { agentPasswordManagementConfigGroup 2 } agentPasswordManagementAging OBJECT-TYPE SYNTAX Integer32 (1..365) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum time that user passwords are valid, in days, from the time the password is set. Once a password expires, the user will be required to enter a new password following the first login after password expiration. A value of 0 indicates that passwords never expire. " ::= { agentPasswordManagementConfigGroup 3 } agentPasswordManagementLockAttempts OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of allowable failed local authentication attempts before the user's account is locked. A value of 0 indicates that user accounts will never be locked. " ::= { agentPasswordManagementConfigGroup 4 } agentPasswordManagementPasswordStrengthCheck OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configures Password Strength Check feature." ::= { agentPasswordManagementConfigGroup 5 } agentPasswordManagementStrengthMinUpperCase OBJECT-TYPE SYNTAX Integer32 (0..16) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of minimum allowable uppercase letters in a password. Minimum of 0 means no restriction on that set of characters." ::= { agentPasswordManagementConfigGroup 6} agentPasswordManagementStrengthMinLowerCase OBJECT-TYPE SYNTAX Integer32 (0..16) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of minimum allowable lowercase letters in a password. Minimum of 0 means no restriction on that set of characters." ::= { agentPasswordManagementConfigGroup 7} agentPasswordManagementStrengthMinNumericNumbers OBJECT-TYPE SYNTAX Integer32 (0..16) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of minimum allowable numeric numbers in a password. Minimum of 0 means no restriction on that set of characters." ::= { agentPasswordManagementConfigGroup 8} agentPasswordManagementStrengthMinSpecialCharacters OBJECT-TYPE SYNTAX Integer32 (0..16) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of minimum allowable special characters in a password. Minimum of 0 means no restriction on that set of characters." ::= { agentPasswordManagementConfigGroup 9} agentPasswordManagementStrengthMaxConsecutiveCharacters OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of maximum consecutive characters can be present in a password. Maximum of 0 means disabling the restriction." ::= { agentPasswordManagementConfigGroup 10} agentPasswordManagementStrengthMaxRepeatedCharacters OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of maximum repeated characters can be present in a password. Maximum of 0 means disabling the restriction." ::= { agentPasswordManagementConfigGroup 11} agentPasswordManagementStrengthMinCharacterClasses OBJECT-TYPE SYNTAX Integer32 (0..4) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of minimum allowable character classes in a password. Minimum of 0 means no restriction on that set of characters." ::= { agentPasswordManagementConfigGroup 12} agentPasswordMgmtLastPasswordSetResult OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Retrieves the last password set Result." ::= { agentPasswordManagementConfigGroup 14} agentPasswordManagementStrengthExcludeKeywordTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentPasswordManagementStrengthExcludeKeywordEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents Password strength restricted keywords from the configurable password." ::= { agentPasswordManagementConfigGroup 15} agentPasswordManagementStrengthExcludeKeywordEntry OBJECT-TYPE SYNTAX AgentPasswordManagementStrengthExcludeKeywordEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents Password strength restricted keywords from the configurable password." INDEX { agentPasswordMgmtStrengthExcludeKeyword } ::= { agentPasswordManagementStrengthExcludeKeywordTable 1 } AgentPasswordManagementStrengthExcludeKeywordEntry ::= SEQUENCE { agentPasswordMgmtStrengthExcludeKeyword DisplayString, agentPasswordMgmtStrengthExcludeKeywordStatus RowStatus } agentPasswordMgmtStrengthExcludeKeyword OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the given keyword string restricted from the configurable password." ::= { agentPasswordManagementStrengthExcludeKeywordEntry 1} agentPasswordMgmtStrengthExcludeKeywordStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Create the Exclude Keyword Index and configure (Create or Destroy) the keyword to it." ::= { agentPasswordManagementStrengthExcludeKeywordEntry 2} --************************************************************************************** --agentIASUserConfigGroup -> Contains MIB objects to configure IAS User Database -- --************************************************************************************** agentIASUserConfigGroup OBJECT IDENTIFIER ::= { agentCLIConfigGroup 7 } agentIASUserConfigCreate OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "Create a new user. When set with a non-empty string, a new user with that name will be created. This object will only return an empty string. This string is limited to alpha-numeric strings (including the '-' and '_' characters)." ::= { agentIASUserConfigGroup 1 } agentIASUserConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentIASUserConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table for dot1x Client details and associated functionality." ::= { agentIASUserConfigGroup 2 } agentIASUserConfigEntry OBJECT-TYPE SYNTAX AgentIASUserConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents entry for port config table." INDEX { agentIASUserIndex} ::= {agentIASUserConfigTable 1 } AgentIASUserConfigEntry ::= SEQUENCE { agentIASUserIndex Integer32, agentIASUserName DisplayString, agentIASUserPassword DisplayString, agentIASUserStatus RowStatus } agentIASUserIndex OBJECT-TYPE SYNTAX Integer32 (0..99) MAX-ACCESS not-accessible STATUS current DESCRIPTION "IAS user config index. " ::= { agentIASUserConfigEntry 1} agentIASUserName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "IAS user name. This string is limited to alpha-numeric strings (including '-' and '_' characters). " ::= { agentIASUserConfigEntry 2} agentIASUserPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "IAS user password." ::= { agentIASUserConfigEntry 3} agentIASUserStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "IAS User Status. active(1) - This user account is active. destroy(6) - Set to this value to remove this user account." ::= { agentIASUserConfigEntry 4 } --************************************************************************************** -- agentLagConfigGroup -- --************************************************************************************** agentLagConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 2 } -- agentLagConfigCreate OBJECT-TYPE -- SYNTAX DisplayString (SIZE(0|1..15)) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Agent LAG Create. -- When this object is set with a non-empty string, a new LAG -- will be created if possible, with the entered string as its -- name. -- Get operation on this MIB object returns a null-value, as -- for the purpose of viewing the LAG name, the user should -- perform the traversal of agentLagSummaryConfigTable. For -- this reason the get operation on this object -- agentLagConfigCreate becomes insignificant." -- ::= { agentLagConfigGroup 1 } agentLagConfigCreate OBJECT-TYPE SYNTAX Integer32 (1..64) MAX-ACCESS read-write STATUS current DESCRIPTION "Agent LAG Create. When this object is set with a LAG index value, a new LAG will be created if possible. Get operation on this MIB object returns a null-value, as for the purpose of viewing the LAG name, the user should perform the traversal of agentLagSummaryConfigTable. For this reason the get operation on this object agentLagConfigCreate becomes insignificant." ::= { agentLagConfigGroup 1 } agentLagSummaryConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentLagSummaryConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A summary table of the switch's LAG config entries" ::= { agentLagConfigGroup 2 } agentLagSummaryConfigEntry OBJECT-TYPE SYNTAX AgentLagSummaryConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's LAG config entry" INDEX { agentLagSummaryLagIndex } ::= { agentLagSummaryConfigTable 1 } AgentLagSummaryConfigEntry ::= SEQUENCE { agentLagSummaryLagIndex Integer32, agentLagSummaryName DisplayString, agentLagSummaryFlushTimer Integer32, agentLagSummaryLinkTrap INTEGER, agentLagSummaryAdminMode INTEGER, agentLagSummaryStpMode INTEGER, agentLagSummaryAddPort Integer32, agentLagSummaryDeletePort Integer32, agentLagSummaryStatus RowStatus, agentLagSummaryType INTEGER, agentLagSummaryPortStaticCapability INTEGER, agentLagSummaryHash INTEGER, agentLagSummaryHashOption Integer32 , agentLagSummaryRateLoadInterval Integer32 } agentLagSummaryLagIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "Agent LAG IfIndex. This value corresponds with the LAG interface in the ifTable." ::= { agentLagSummaryConfigEntry 1 } agentLagSummaryName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) -- MAX-ACCESS read-write MAX-ACCESS read-only STATUS current DESCRIPTION "Agent LAG Name. The associated name of the LAG used during creation." ::= { agentLagSummaryConfigEntry 2 } agentLagSummaryFlushTimer OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Agent LAG FlushTimer." ::= { agentLagSummaryConfigEntry 3 } agentLagSummaryLinkTrap OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Agent LAG LinkTrap. Configures sending Link Up/Down traps when the LAG interface goes Up or Down." ::= { agentLagSummaryConfigEntry 4 } agentLagSummaryAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Agent LAG AdminMode. Administratively enables or disables this LAG interface." ::= { agentLagSummaryConfigEntry 5 } agentLagSummaryStpMode OBJECT-TYPE SYNTAX INTEGER { dot1d(1), fast(2), off(3), dot1s(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Agent LAG StpMode If Dot1d is enabled, the valid values are: dot1d(1), fast(2), and off(3) If Dot1s is enabled, the valid values are: off(3) and dot1s(4)" ::= { agentLagSummaryConfigEntry 6 } agentLagSummaryAddPort OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "Agent LAG AddPort. Set to a non 0 value to add a port to the LAG. Values correspond to ifIndex values in the ifTable. Note: agentPortType for the port to be added must be full duplex and the same speed as previously added port(s), if any." ::= { agentLagSummaryConfigEntry 7 } agentLagSummaryDeletePort OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "Agent LAG DeletePort. Set to a non 0 value to remove a port from the LAG. Values correspond to ifIndex values in the ifTable." ::= { agentLagSummaryConfigEntry 8 } agentLagSummaryStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Agent LAG Status. active(1) - This LAG is enabled. destroy(6) - Set to this value to remove the LAG." ::= { agentLagSummaryConfigEntry 9 } agentLagSummaryType OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Agent LAG Type. static(1) - This LAG is staticly maintained. dynamic(2) - This LAG is dynamicly maintained." ::= { agentLagSummaryConfigEntry 10 } agentLagSummaryPortStaticCapability OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Agent LAG Static Capability enable(1) - Static capability is enabled for this LAG interface disable(2) - Static capability is disabled for this LAG interface" DEFVAL { disable } ::= { agentLagSummaryConfigEntry 11 } agentLagSummaryHash OBJECT-TYPE SYNTAX INTEGER { src-mac(1), dst-mac(2), src-dst-mac(3), src-ip-src-ipport(7), dst-ip-dst-ipport(8), src-dst-ip-ipports(9) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Agent LAG HASH algorithm. Allow the user to specify which hash distribution algorithm want to be applied all LAG groups. src-mac(1) - Source MAC address. dst-mac(2) - Destination MAC address. src-dst-mac(3) - Source and Destination MAC address. src-ip(4) - Source IP address (IPv4 and IPv6). dst-ip(5) - Destination IP address (IPv4 and IPv6). src-dst-ip(6) - Source and Destination IP address (IPv4 and IPv6). src-ip-src-ipport(7) - Source IP address and Source IP L4 Port (IPv4 and IPv6). dst-ip-dst-ipport(8) - Destination IP address and Destination IP L4 Port (IPv4 and IPv6). src-dst-ip-ipports(9) - Source and Destination IP address and Source IP L4 Port and Destination IP L4 Port (IPv4 and IPv6)(default). src-dst-ip-x1(10) - Source and Destination IP address XOR Mode 1. src-dst-ip-x1(11) - Source and Destination IP address XOR Mode 2. src-dst-ip-x1(12) - Source and Destination IP address XOR Mode 4. src-dst-ip-x1(13) - Source and Destination IP address XOR Mode 8." ::= { agentLagSummaryConfigEntry 12 } agentLagSummaryHashOption OBJECT-TYPE SYNTAX Integer32 (1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "LAG Hashing Option. Valid values correspond to 1 (=Source MAC, VLAN, EtherType, and incoming port associated with the packet) 2 (=Destination MAC, VLAN, EtherType, and incoming port associated with the packet) 3 (=Source/Destination MAC, VLAN, EtherType, and incoming port associated with the packet) 4 (=Source IP and Source TCP/UDP fields of the packet) 5 (=Destination IP and Destination TCP/UDP Port fields of the packet) 6 (=Source/Destination IP and source/destination TCP/UDP Port fields of the packet) 7 (=Enhanced hashing mode) Support for particular options may vary by device." ::= { agentLagSummaryConfigEntry 13 } agentLagSummaryRateLoadInterval OBJECT-TYPE SYNTAX Integer32 (30..600) MAX-ACCESS read-write STATUS current DESCRIPTION "The length of time for which data is used to compute load statistics. The value is given in seconds, and must be a multiple of 30. The allowable range is 30 to 600 seconds." ::= { agentLagSummaryConfigEntry 15 } --************************************************************************************** agentLagDetailedConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentLagDetailedConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A detailed table of the switch's LAG config entries" ::= { agentLagConfigGroup 3 } agentLagDetailedConfigEntry OBJECT-TYPE SYNTAX AgentLagDetailedConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's LAG config entry" INDEX { agentLagDetailedLagIndex, agentLagDetailedIfIndex } ::= { agentLagDetailedConfigTable 1 } AgentLagDetailedConfigEntry ::= SEQUENCE { agentLagDetailedLagIndex Integer32, agentLagDetailedIfIndex Integer32, agentLagDetailedPortSpeed OBJECT IDENTIFIER, agentLagDetailedPortStatus INTEGER } agentLagDetailedLagIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "LAG index" ::= { agentLagDetailedConfigEntry 1 } agentLagDetailedIfIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "LAG port index" ::= { agentLagDetailedConfigEntry 2 } agentLagDetailedPortSpeed OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "LAG port speed. See agentPortType for a description and list of valid values." ::= { agentLagDetailedConfigEntry 3 } agentLagDetailedPortStatus OBJECT-TYPE SYNTAX INTEGER { active(1), inactive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "LAG port status. active(1) - Actively participating in the LAG. inactive(2) - Not participating in the LAG." ::= { agentLagDetailedConfigEntry 4 } --************************************************************************************** agentLagConfigStaticCapability OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Agent LAG Static Capability. Configures whether Static LAGs are supported on this device." ::= { agentLagConfigGroup 4 } agentLagConfigGroupHashOption OBJECT-TYPE SYNTAX Integer32 (1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "LAG Hashing Option. Valid values correspond to 1 (=Source MAC, VLAN, EtherType, and incoming port associated with the packet) 2 (=Destination MAC, VLAN, EtherType, and incoming port associated with the packet) 3 (=Source/Destination MAC, VLAN, EtherType, and incoming port associated with the packet) 4 (=Source IP and Source TCP/UDP fields of the packet) 5 (=Destination IP and Destination TCP/UDP Port fields of the packet) 6 (=Source/Destination IP and source/destination TCP/UDP Port fields of the packet) 7 (=Enhanced hashing mode) Support for particular options may vary by device. In BCM 53115 device only options 1 to 3 are support and only MAC address associated with the packet is used. " ::= { agentLagConfigGroup 5 } --************************************************************************************** -- agentNetworkConfigGroup -- --************************************************************************************** agentNetworkConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 3 } agentNetworkIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's network ip address" ::= { agentNetworkConfigGroup 1 } agentNetworkSubnetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's network subnet mask" ::= { agentNetworkConfigGroup 2 } agentNetworkDefaultGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's network default gateway" ::= { agentNetworkConfigGroup 3 } agentNetworkBurnedInMacAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's network Burned-In MAC address" ::= { agentNetworkConfigGroup 4 } agentNetworkLocalAdminMacAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The switch's network locally administered MAC address" ::= { agentNetworkConfigGroup 5 } agentNetworkMacAddressType OBJECT-TYPE SYNTAX INTEGER { burned-in(1), local(2) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The switch's network Mac Address Type" ::= { agentNetworkConfigGroup 6 } agentNetworkConfigProtocol OBJECT-TYPE SYNTAX INTEGER { none(1), bootp(2), dhcp(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's network config protocol" ::= { agentNetworkConfigGroup 7 } agentNetworkWebMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The switch's network config protocol on next bootup This object has been obsoleted by agentHTTPWebMode." ::= { agentNetworkConfigGroup 8 } agentNetworkJavaMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Configures the use of the Java interface through the Web. This object has been obsoleted by agentHTTPJavaMode." ::= { agentNetworkConfigGroup 9 } agentNetworkMgmtVlan OBJECT-TYPE SYNTAX Integer32 (1..4093) MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN ID through which the switch can be managed using the agentNetworkIPAddress" ::= { agentNetworkConfigGroup 10 } agentNetworkConfigProtocolDhcpRenew OBJECT-TYPE SYNTAX INTEGER { renew(1) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The switch's network config protocol dhcp is renewed." ::= { agentNetworkConfigGroup 11 } agentNetworkConfigIpDhcpRenew OBJECT-TYPE SYNTAX INTEGER { renew(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Renew serviceport or interface ip address when dhcp is enabled. Equivalent to ip dhcp restart. deprecate agentNetworkConfigProtocolDhcpRenew and agentServicePortProtocolDhcpRenew" ::= { agentNetworkConfigGroup 20 } agentNetworkConfigIpv6DhcpRenew OBJECT-TYPE SYNTAX INTEGER { renew(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Renew serviceport or interface ipv6 address when dhcp is enabled. Equivalent to ipv6 dhcp restart." ::= { agentNetworkConfigGroup 21 } --************************************************************************************** -- ipv6 agentNetworkPortConfigGroup -- --************************************************************************************** agentNetworkIpv6AdminMode OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The network port IPv6 administrative state" ::= { agentNetworkConfigGroup 12 } agentNetworkIpv6Gateway OBJECT-TYPE SYNTAX Ipv6AddressPrefix MAX-ACCESS read-write STATUS current DESCRIPTION "The network port IPv6 Gateway Address If Ipv6 Address is unspecified (all zero), this means network Ipv6 gateway is not set." ::= { agentNetworkConfigGroup 13 } agentNetworkIpv6AddrTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentNetworkIpv6AddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The list of IPv6 address prefixes for the network port." ::= { agentNetworkConfigGroup 14 } agentNetworkIpv6AddrEntry OBJECT-TYPE SYNTAX AgentNetworkIpv6AddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An interface entry containing objects of a particular IPv6 address prefix" INDEX { agentNetworkIpv6AddrPrefix } ::= { agentNetworkIpv6AddrTable 1 } AgentNetworkIpv6AddrEntry ::= SEQUENCE { agentNetworkIpv6AddrPrefix Ipv6AddressPrefix, agentNetworkIpv6AddrPrefixLength INTEGER, agentNetworkIpv6AddrEuiFlag INTEGER, agentNetworkIpv6AddrStatus RowStatus } agentNetworkIpv6AddrPrefix OBJECT-TYPE SYNTAX Ipv6AddressPrefix MAX-ACCESS not-accessible --read-write STATUS current DESCRIPTION "The service port IPv6 Address Prefix" ::= { agentNetworkIpv6AddrEntry 1 } agentNetworkIpv6AddrPrefixLength OBJECT-TYPE SYNTAX INTEGER (0..128) MAX-ACCESS read-create STATUS current DESCRIPTION "The service port IPv6 Address Prefix Length" ::= { agentNetworkIpv6AddrEntry 2 } agentNetworkIpv6AddrEuiFlag OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The service port IPv6 Eui Flag" ::= { agentNetworkIpv6AddrEntry 3 } agentNetworkIpv6AddrStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "" ::= { agentNetworkIpv6AddrEntry 4} agentNetworkIpv6AddressAutoConfig OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The ipv6 address autoconfig allows the device to perform IPv6 stateless address auto-configuration to discover prefixes on the link and then to add the eui-64 based addresses to the network interface." DEFVAL { disable } ::= { agentNetworkConfigGroup 15 } agentNetworkIpv6ConfigProtocol OBJECT-TYPE SYNTAX INTEGER { none(1), dhcp(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's network IPv6 config protocol" ::= { agentNetworkConfigGroup 16 } agentNetworkDhcp6ClientDuid OBJECT-TYPE SYNTAX DisplayString (SIZE(1..255)) MAX-ACCESS read-only STATUS current DESCRIPTION " The DHCPv6 Client unique DUID. This value cannot be modified" ::= { agentNetworkConfigGroup 17 } --************************************************************************************** -- ipv6 agentNetworkStatsGroup -- --************************************************************************************** agentNetworkStatsGroup OBJECT IDENTIFIER ::= { agentNetworkConfigGroup 18 } agentNetworkDhcp6ADVERTISEMessagesReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages of type ADVERTISE that have been received by the DHCPv6 client on the network port." ::= { agentNetworkStatsGroup 1 } agentNetworkDhcp6REPLYMessagesReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages of type REPLY that have been received by the DHCPv6 client on the network port." ::= { agentNetworkStatsGroup 2 } agentNetworkDhcp6ADVERTISEMessagesDiscarded OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages of type ADVERTISE that have been discarded by the DHCPv6 client on the network port." ::= { agentNetworkStatsGroup 3 } agentNetworkDhcp6REPLYMessagesDiscarded OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages of type REPLY that have been discarded by the DHCPv6 client on the network port." ::= { agentNetworkStatsGroup 4 } agentNetworkDhcp6MalformedMessagesReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages received malformed by the DHCPv6 client on the network port." ::= { agentNetworkStatsGroup 5 } agentNetworkDhcp6SOLICITMessagesSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages of type SOLICIT that have been sent by the DHCPv6 client on the network port." ::= { agentNetworkStatsGroup 6 } agentNetworkDhcp6REQUESTMessagesSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages of type REQUEST that have been sent by the DHCPv6 client on the network port." ::= { agentNetworkStatsGroup 7 } agentNetworkDhcp6RENEWMessagesSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages of type RENEW that have been sent by the DHCPv6 client on the network port." ::= { agentNetworkStatsGroup 8 } agentNetworkDhcp6REBINDMessagesSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages of type REBIND that have been sent by the DHCPv6 client on the network port." ::= { agentNetworkStatsGroup 9 } agentNetworkDhcp6RELEASEMessagesSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages of type RELEASE that have been sent by the DHCPv6 client on the network port." ::= { agentNetworkStatsGroup 10 } agentNetworkDhcp6StatsReset OBJECT-TYPE SYNTAX INTEGER { none(0), reset(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear the DHCPv6 Client statistics on the network port. A value of reset(1) is used to reset the statistics. A read on this object will always return the value none(0). The value none(0) cannot be forcibly set by the administrator." ::= { agentNetworkStatsGroup 11 } --************************************************************************************** -- agentServicePortConfigGroup -- --************************************************************************************** agentServicePortConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 4 } agentServicePortIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's ServicePort ip address" ::= { agentServicePortConfigGroup 1 } agentServicePortSubnetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's ServicePort subnet mask" ::= { agentServicePortConfigGroup 2 } agentServicePortDefaultGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's ServicePort default gateway" ::= { agentServicePortConfigGroup 3 } agentServicePortBurnedInMacAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's ServicePort Burned-In MAC address" ::= { agentServicePortConfigGroup 4 } agentServicePortConfigProtocol OBJECT-TYPE SYNTAX INTEGER { none(1), bootp(2), dhcp(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's ServicePort config protocol" ::= { agentServicePortConfigGroup 5 } agentServicePortProtocolDhcpRenew OBJECT-TYPE SYNTAX INTEGER { renew(1) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The switch's ServicePort protocol dhcp is renewed." ::= { agentServicePortConfigGroup 6 } --************************************************************************************** -- agentServicePort2ConfigGroup -- --************************************************************************************** -- agentServicePort2ConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 5 } -- -- agentServicePort2IPAddress OBJECT-TYPE -- SYNTAX IpAddress -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The switch's ServicePort2 ip address" -- ::= { agentServicePort2ConfigGroup 1 } -- -- agentServicePort2SubnetMask OBJECT-TYPE -- SYNTAX IpAddress -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The switch's ServicePort2 subnet mask" -- ::= { agentServicePort2ConfigGroup 2 } -- -- agentServicePort2DefaultGateway OBJECT-TYPE -- SYNTAX IpAddress -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The switch's ServicePort2 default gateway" -- ::= { agentServicePort2ConfigGroup 3 } -- -- agentServicePort2BurnedInMacAddress OBJECT-TYPE -- SYNTAX PhysAddress -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The switch's ServicePort2 Burned-In MAC address" -- ::= { agentServicePort2ConfigGroup 4 } -- -- agentServicePort2ConfigProtocol OBJECT-TYPE -- SYNTAX INTEGER { -- none(1), -- bootp(2), -- dhcp(3) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The switch's ServicePort2 config protocol" -- ::= { agentServicePort2ConfigGroup 5 } --************************************************************************************** -- ipv6 mgmt on serviceport -- --************************************************************************************** agentServicePortIpv6AdminMode OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The service port IPv6 administrative state" ::= { agentServicePortConfigGroup 7 } agentServicePortIpv6Gateway OBJECT-TYPE SYNTAX Ipv6AddressPrefix MAX-ACCESS read-write STATUS current DESCRIPTION "The service port IPv6 Gateway Address If Ipv6 Address is unspecified (all zero), this means serviceport Ipv6 gateway is not set." ::= { agentServicePortConfigGroup 8 } agentServicePortIpv6AddrTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentServicePortIpv6AddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The list of IPv6 address prefixes for the service port." ::= { agentServicePortConfigGroup 9 } agentServicePortIpv6AddrEntry OBJECT-TYPE SYNTAX AgentServicePortIpv6AddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An interface entry containing objects of a particular IPv6 address prefix" INDEX { agentServicePortIpv6AddrPrefix } ::= { agentServicePortIpv6AddrTable 1 } AgentServicePortIpv6AddrEntry ::= SEQUENCE { agentServicePortIpv6AddrPrefix Ipv6AddressPrefix, agentServicePortIpv6AddrPrefixLength INTEGER, agentServicePortIpv6AddrEuiFlag INTEGER, agentServicePortIpv6AddrStatus RowStatus } agentServicePortIpv6AddrPrefix OBJECT-TYPE SYNTAX Ipv6AddressPrefix MAX-ACCESS not-accessible --read-write STATUS current DESCRIPTION "The service port IPv6 Address Prefix" ::= { agentServicePortIpv6AddrEntry 1 } agentServicePortIpv6AddrPrefixLength OBJECT-TYPE SYNTAX INTEGER (0..128) MAX-ACCESS read-create STATUS current DESCRIPTION "The service port IPv6 Address Prefix Length" ::= { agentServicePortIpv6AddrEntry 2 } agentServicePortIpv6AddrEuiFlag OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The service port IPv6 Eui Flag" ::= { agentServicePortIpv6AddrEntry 3 } agentServicePortIpv6AddrStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "" ::= { agentServicePortIpv6AddrEntry 4} agentServicePortIpv6AddressAutoConfig OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The ipv6 address autoconfig allows the device to perform IPv6 stateless address auto-configuration to discover prefixes on the link and then to add the eui-64 based addresses to the serviceport interface." DEFVAL { enable } ::= { agentServicePortConfigGroup 10 } agentServicePortIpv6ConfigProtocol OBJECT-TYPE SYNTAX INTEGER { none(1), dhcp(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The Service Port.s IPv6 protocol configured on the switch." ::= { agentServicePortConfigGroup 11 } agentServicePortDhcp6ClientDuid OBJECT-TYPE SYNTAX DisplayString (SIZE(1..255)) MAX-ACCESS read-only STATUS current DESCRIPTION " The DHCPv6 Client unique DUID. This value cannot be modified" ::= { agentServicePortConfigGroup 12 } --************************************************************************************** -- ipv6 agentServicePortStatsGroup -- --************************************************************************************** agentServicePortStatsGroup OBJECT IDENTIFIER ::= {agentServicePortConfigGroup 13 } agentServicePortDhcp6ADVERTISEMessagesReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages of type ADVERTISE that have been received by the DHCPv6 client on the service port." ::= { agentServicePortStatsGroup 1 } agentServicePortDhcp6REPLYMessagesReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages of type REPLY that have been received by the DHCPv6 client on the service port." ::= { agentServicePortStatsGroup 2 } agentServicePortDhcp6ADVERTISEMessagesDiscarded OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages of type ADVERTISE that have been discarded by the DHCPv6 client on the service port." ::= { agentServicePortStatsGroup 3 } agentServicePortDhcp6REPLYMessagesDiscarded OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages of type REPLY that have been discarded by the DHCPv6 client on the service port." ::= { agentServicePortStatsGroup 4 } agentServicePortDhcp6MalformedMessagesReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages received malformed by the DHCPv6 client on the service port." ::= { agentServicePortStatsGroup 5 } agentServicePortDhcp6SOLICITMessagesSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages of type SOLICIT that have been sent by the DHCPv6 client on the service port." ::= { agentServicePortStatsGroup 6 } agentServicePortDhcp6REQUESTMessagesSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages of type REQUEST that have been sent by the DHCPv6 client on the service port." ::= { agentServicePortStatsGroup 7 } agentServicePortDhcp6RENEWMessagesSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages of type RENEW that have been sent by the DHCPv6 client on the service port." ::= { agentServicePortStatsGroup 8 } agentServicePortDhcp6REBINDMessagesSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages of type REBIND that have been sent by the DHCPv6 client on the service port." ::= { agentServicePortStatsGroup 9 } agentServicePortDhcp6RELEASEMessagesSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The no. of DHCPv6 messages of type RELEASE that have been sent by the DHCPv6 client on the service port." ::= { agentServicePortStatsGroup 10 } agentServicePortDhcp6StatsReset OBJECT-TYPE SYNTAX INTEGER { none(0), reset(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear the DHCPv6 Client statistics on the service port. A value of reset(1) is used to reset the statistics. A read on this object will always return the value none(0). The value none(0) cannot be forcibly set by the administrator." ::= { agentServicePortStatsGroup 11 } --************************************************************************************** -- agentSnmpConfigGroup -- --************************************************************************************** agentSnmpConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 6 } agentSnmpCommunityCreate OBJECT-TYPE SYNTAX DisplayString (SIZE (1..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "Creates a new SNMP Community entry. Defaults: IPAddress 0.0.0.0 IpMask 0.0.0.0 AccessMode read-only Status config" ::= { agentSnmpConfigGroup 1 } agentSnmpCommunityConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSnmpCommunityConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the switch's SNMP Config entries" ::= { agentSnmpConfigGroup 2 } agentSnmpCommunityConfigEntry OBJECT-TYPE SYNTAX AgentSnmpCommunityConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's SNMP Config entry" INDEX {agentSnmpCommunityIndex } ::= { agentSnmpCommunityConfigTable 1 } AgentSnmpCommunityConfigEntry ::= SEQUENCE { agentSnmpCommunityIndex Integer32, agentSnmpCommunityName DisplayString, agentSnmpCommunityIPAddress IpAddress, agentSnmpCommunityIPMask IpAddress, agentSnmpCommunityAccessMode INTEGER, agentSnmpCommunityStatus INTEGER } agentSnmpCommunityIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Snmp Community Index" ::= { agentSnmpCommunityConfigEntry 1 } agentSnmpCommunityName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp Community Name This name identifies each SNMP community; the name can be up to 16 characters, and it is case-sensitive. Community names in the SNMP community must be unique. If you make multiple entries using the same community name, the first entry is kept and processed and all duplicate entries are ignored. " ::= { agentSnmpCommunityConfigEntry 2 } agentSnmpCommunityIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp Community IP Address Client IP Address - This attribute is an IP address (or portion thereof) from which this device will accept SNMP packets with the associated community. The requesting entity's IP address is logical-ANDed with the Client IP Mask and the result must match the Client IP Address. Note: If the Client IP Mask is set to 0.0.0.0, a Client IP Address of 0.0.0.0 matches all IP addresses. " ::= { agentSnmpCommunityConfigEntry 3 } agentSnmpCommunityIPMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp Community IP Mask Client IP Mask - This attribute is a mask to be logical-ANDed with the requesting entity's IP address before comparison with the Client IP Address. If the result matches with Client IP Address then the address is an authenticated IP address. For example, if the Client IP Address is 9.47.128.0 and the corresponding Client IP Mask is 255.255.255.0, a range of incoming IP addresses would match, that is, the incoming IP addresses could be a value in the following range: 9.47.128.0 to 9.47.128.255. To have a specific IP address be the only authenticated IP address, set the Client IP Address to the required IP address and set the Client IP Mask to 255.255.255.255. " ::= { agentSnmpCommunityConfigEntry 4 } agentSnmpCommunityAccessMode OBJECT-TYPE SYNTAX INTEGER { read-only(1), read-write(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp Community Access Mode Access Mode - This value can be read-only or read/write. A community with a read-only access allows for switch information to be displayed. A community with a read/write access allows for configuration changes to be made and for information to be displayed. " ::= { agentSnmpCommunityConfigEntry 5 } agentSnmpCommunityStatus OBJECT-TYPE SYNTAX INTEGER { active(1), notInService(2), config(3), destroy(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp Community Status. active(1) - This community is active, allowing SNMP managers associated with this community to manage the switch according to its access right. notInService(2) - This community is not active; no SNMP requests using this community will be accepted. In this case the SNMP manager associated with this community cannot manage the switch until the Status is changed back to active(1). config(3) - The community Status must be set to this value in order to configure it. When creating a new community entry, initial Status will be set to this value. destroy(4) - Set to this value to remove the community from the agent." ::= { agentSnmpCommunityConfigEntry 6 } --************************************************************************************** -- agentSnmpTrapReceiverConfigTable -- --************************************************************************************** agentSnmpTrapReceiverCreate OBJECT-TYPE SYNTAX DisplayString (SIZE(1..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "Creates a new trap receiver entry. Defaults: IPAddress 0.0.0.0 status config" ::= { agentSnmpConfigGroup 3 } agentSnmpTrapReceiverConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSnmpTrapReceiverConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Trap messages are sent across a network to an SNMP Network Manager. These messages alert the manager to events occurring within the switch or on the network. Up to six simultaneous trap receivers are supported. " ::= { agentSnmpConfigGroup 4 } agentSnmpTrapReceiverConfigEntry OBJECT-TYPE SYNTAX AgentSnmpTrapReceiverConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's Snmp Trace Receiver Config entry" INDEX { agentSnmpTrapReceiverIndex } ::= { agentSnmpTrapReceiverConfigTable 1 } AgentSnmpTrapReceiverConfigEntry ::= SEQUENCE { agentSnmpTrapReceiverIndex Integer32, agentSnmpTrapReceiverCommunityName DisplayString, agentSnmpTrapReceiverIPAddress DisplayString, agentSnmpTrapReceiverStatus INTEGER, agentSnmpTrapReceiverVersion INTEGER, agentSnmpTrapReceiverSecurityLevel INTEGER, agentSnmpTrapReceiverPort Integer32 } agentSnmpTrapReceiverIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Snmp Trap Receiver Index" ::= { agentSnmpTrapReceiverConfigEntry 1 } agentSnmpTrapReceiverCommunityName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp Trap Receiver Community Name. This is the SNMP community name of the remote network manager; the name can be up to 16 characters, and is case-sensitive. " ::= { agentSnmpTrapReceiverConfigEntry 2 } agentSnmpTrapReceiverIPAddress OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Trap receiver IP or IPv6 address" ::= { agentSnmpTrapReceiverConfigEntry 3 } agentSnmpTrapReceiverStatus OBJECT-TYPE SYNTAX INTEGER { active(1), notInService(2), config(3), destroy(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp Trap Reciever Status. active(1) - This trap receiver is active, allowing SNMP Traps to be sent to this receiver. notInService(2) - This trap reciever is not active; no SNMP Traps will be sent to this reciever until it's set back to active(1). config(3) - The trap reciever Status must be set to this value in order to configure it. When creating a new trap receiver entry, the Status will initially be set to this value. Note: agentSnmpTrapReceiverIPAddress must be set to non-zero before changing to active(1) or notInService(2). destroy(4) - Set to this value to remove the trap receiver entry from the agent." ::= { agentSnmpTrapReceiverConfigEntry 4 } agentSnmpTrapReceiverVersion OBJECT-TYPE SYNTAX INTEGER { snmpv1(1), snmpv2c(2), snmpv3(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The version of trap sent to this Reciever. snmpv1(1) - This will send a SNMPv1 trap. snmpv2c(2) - This will send a SNMPv2c trap. snmpv3(3) - This will send a SNMPv3 trap." DEFVAL { snmpv2c } ::= { agentSnmpTrapReceiverConfigEntry 5 } agentSnmpTrapReceiverSecurityLevel OBJECT-TYPE SYNTAX INTEGER { none(1), auth(2), priv(3), notSupport(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The security level of SNMPv3 trap reciever. none(1) - SNMPv3 noAuthNoPriv security level. auth(2) - SNMPv3 authNoPriv security level. priv(3) - SNMPv3 authPriv security level notSupport(4) - only support on SNMPv3" DEFVAL { none } ::= { agentSnmpTrapReceiverConfigEntry 6 } agentSnmpTrapReceiverPort OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Trap receiver UDP port" DEFVAL { 162 } ::= { agentSnmpTrapReceiverConfigEntry 7 } --************************************************************************************** -- agentSnmpTrapFlagsConfigGroup -- --************************************************************************************** agentSnmpTrapFlagsConfigGroup OBJECT IDENTIFIER ::= { agentSnmpConfigGroup 5 } agentSnmpAuthenticationTrapFlag OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Authentication Flag - Enable/Disable authentication Flag." ::= { agentSnmpTrapFlagsConfigGroup 1 } agentSnmpLinkUpDownTrapFlag OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Link Up/Down Flag - Enable/Disable Link Up/Link Down traps for the entire switch. When set to Enable, the Link Up/Down traps will be sent only if the Link Trap flag setting associated with the port (Port Configuration Menu) is set to Enable. " ::= { agentSnmpTrapFlagsConfigGroup 2 } agentSnmpMultipleUsersTrapFlag OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Multiple Users Flag - Enable/Disable Multiple User traps. When the value is set to Enable, a Multiple User Trap is sent whenever someone logs in to the terminal interface (EIA 232 or Telnet) and there is already an existing terminal interface session. " ::= { agentSnmpTrapFlagsConfigGroup 3 } agentSnmpSpanningTreeTrapFlag OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Spanning Tree Flag - This flag enables the sending of new root traps and topology change notification traps." ::= { agentSnmpTrapFlagsConfigGroup 4 } agentSnmpACLTrapFlag OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable ACL traps." ::= { agentSnmpTrapFlagsConfigGroup 5 } -- agentSnmpBroadcastStormTrapFlag OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2) -- } -- MAX-ACCESS read-write -- STATUS obsolete -- DESCRIPTION -- "Broadcast Storm Flag - This flag enables or disables the broadcast -- storm trap. You must also enable Broadcast Storm Recovery Mode -- (see the Switch Configuration Menu). When this -- value is set to Enable and Broadcast Storm Recovery mode is set to Enable, -- the Broadcast Storm Start/End traps are sent when the switch enters and -- leaves Broadcast Storm Recovery. -- " -- ::= { agentSnmpTrapFlagsConfigGroup 5 } --/* Add for DOM support by KevinLee 2014/04/28*/ agentSnmpTransceiverTrapFlag OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Transceiver Flag - Enable/Disable Transceiver traps." ::= { agentSnmpTrapFlagsConfigGroup 7 } --************************************************************************************** -- agentSnmpInformConfigTable -- --************************************************************************************** agentSnmpInformConfigGroup OBJECT IDENTIFIER ::= { agentSnmpConfigGroup 6 } agentSnmpInformAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp Inform Admin Mode" ::= { agentSnmpInformConfigGroup 1 } agentSnmpInformRetires OBJECT-TYPE SYNTAX Integer32 (0..100) MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp Inform Retires" DEFVAL { 3 } ::= { agentSnmpInformConfigGroup 2 } agentSnmpInformTimeout OBJECT-TYPE SYNTAX Integer32 (0..1000) MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp Inform Timeout" DEFVAL { 15 } ::= { agentSnmpInformConfigGroup 3 } agentSnmpInformConfigTableCreate OBJECT-TYPE SYNTAX DisplayString (SIZE(1..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "Creates a new trap inform entry. Defaults: IPAddress 0.0.0.0 status config" ::= { agentSnmpInformConfigGroup 4 } agentSnmpInformConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSnmpInformConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Trap messages are sent across a network to an SNMP Network Manager. These messages alert the manager to events occurring within the switch or on the network. Up to six simultaneous trap receivers are supported." ::= { agentSnmpInformConfigGroup 5 } agentSnmpInformConfigEntry OBJECT-TYPE SYNTAX AgentSnmpInformConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's Snmp Inform Config entry" INDEX { agentSnmpInformIndex } ::= { agentSnmpInformConfigTable 1 } AgentSnmpInformConfigEntry ::= SEQUENCE { agentSnmpInformIndex Integer32, agentSnmpInformName DisplayString, agentSnmpInformIpAddress InetAddress, agentSnmpInformVersion INTEGER, agentSnmpInformStatus INTEGER, agentSnmpInformSecurityLevel INTEGER } agentSnmpInformIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Snmp Inform Index" ::= { agentSnmpInformConfigEntry 1 } agentSnmpInformName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp Inform Name. This is the SNMP community name of the remote network manager; the name can be up to 16 characters, and is case-sensitive." ::= { agentSnmpInformConfigEntry 2 } agentSnmpInformIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp Inform IP or IPv6 address." ::= { agentSnmpInformConfigEntry 3 } agentSnmpInformVersion OBJECT-TYPE SYNTAX INTEGER { snmpv2c(2), snmpv3(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The version of inform sent to this Reciever. snmpv2c(2) - This will send a SNMPv2c inform. snmpv3(3) - This will send a SNMPv3 inform." DEFVAL { snmpv2c } ::= { agentSnmpInformConfigEntry 4 } agentSnmpInformStatus OBJECT-TYPE SYNTAX INTEGER { active(1), notInService(2), config(3), destroy(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp Trap Inform Status. active(1) - This trap Inform is active, allowing SNMP Traps to be sent to this receiver. notInService(2) - This trap Inform is not active; no SNMP Traps will be sent to this reciever until it's set back to active(1). config(3) - The trap Inform Status must be set to this value in order to configure it. When creating a new trap receiver entry, the Status will initially be set to this value. Note: agentSnmpTrapReceiverIPAddress must be set to non-zero before changing to active(1) or notInService(2). destroy(4) - Set to this value to remove the trap Inform entry from the agent." ::= { agentSnmpInformConfigEntry 5 } agentSnmpInformSecurityLevel OBJECT-TYPE SYNTAX INTEGER { none(1), auth(2), priv(3), notSupport(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The security level of SNMPv3 trap inform. none(1) - SNMPv3 noAuthNoPriv security level. auth(2) - SNMPv3 authNoPriv security level. priv(3) - SNMPv3 authPriv security level notSupport(4) - only support on SNMPv3" ::= { agentSnmpInformConfigEntry 6 } --************************************************************************************** -- agentSnmpUserConfigTable -- --************************************************************************************** agentSnmpUserConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSnmpUserConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "SNMP user config table" ::= { agentSnmpConfigGroup 7 } agentSnmpUserConfigEntry OBJECT-TYPE SYNTAX AgentSnmpUserConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's Snmp User Config entry" INDEX { agentSnmpUserIndex } ::= { agentSnmpUserConfigTable 1 } AgentSnmpUserConfigEntry ::= SEQUENCE { agentSnmpUserIndex Integer32, agentSnmpUserUsername DisplayString, agentSnmpUserAuthentication INTEGER, agentSnmpUserAuthenticationPassword DisplayString, agentSnmpUserEncryption INTEGER, agentSnmpUserEncryptionPassword DisplayString, agentSnmpUserStatus INTEGER } agentSnmpUserIndex OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Snmp User Index" ::= { agentSnmpUserConfigEntry 1 } agentSnmpUserUsername OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp User Name." ::= { agentSnmpUserConfigEntry 2 } agentSnmpUserAuthentication OBJECT-TYPE SYNTAX INTEGER { none(1), md5(2), sha(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp User Authentication." DEFVAL { none } ::= { agentSnmpUserConfigEntry 3 } agentSnmpUserAuthenticationPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp User Authentication Password." ::= { agentSnmpUserConfigEntry 4 } agentSnmpUserEncryption OBJECT-TYPE SYNTAX INTEGER { none(1), des(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp User Encryption." DEFVAL { none } ::= { agentSnmpUserConfigEntry 5 } agentSnmpUserEncryptionPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp User Encryption Password." ::= { agentSnmpUserConfigEntry 6 } agentSnmpUserStatus OBJECT-TYPE SYNTAX INTEGER { active(1), create(4), destory(6) } MAX-ACCESS read-create STATUS current DESCRIPTION "The status of SNMP user. active(1) - This snmp user is active. create(4) - Create a new SNMP user. destory(6) - Delete a SNMP user." DEFVAL { active } ::= { agentSnmpUserConfigEntry 7 } --************************************************************************************** -- agentSnmpEngineIdConfigTable -- --************************************************************************************** agentSnmpEngineIdConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSnmpEngineIdConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "SNMP EngineID config table" ::= { agentSnmpConfigGroup 8 } --************************************************************************************** -- agentSnmpTrapSourceInterface -- --************************************************************************************** agentSnmpTrapSourceInterface OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-write STATUS current DESCRIPTION "A source-interface selection on an Interface Index (like vlan based routing interface, port based routing interface, loopback interface, tunnel interface). A non-zero value indicates ifIndex for the corresponding interface entry in the ifTable is selected. A zero value indicates the source-interface un-selection." ::= { agentSnmpConfigGroup 9 } agentSnmpEngineIdConfigEntry OBJECT-TYPE SYNTAX AgentSnmpEngineIdConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's Snmp EngineID Config entry" INDEX { agentSnmpEngineIdIndex } ::= { agentSnmpEngineIdConfigTable 1 } AgentSnmpEngineIdConfigEntry ::= SEQUENCE { agentSnmpEngineIdIndex Integer32, agentSnmpEngineIdIpAddress InetAddress, agentSnmpEngineIdString DisplayString, agentSnmpEngineIdStatus INTEGER } agentSnmpEngineIdIndex OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Snmp EngineID Index" ::= { agentSnmpEngineIdConfigEntry 1 } agentSnmpEngineIdIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp EngineID IP or IPv6 address." ::= { agentSnmpEngineIdConfigEntry 2 } agentSnmpEngineIdString OBJECT-TYPE SYNTAX DisplayString (SIZE(1..24)) MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Snmp EngineID String" ::= { agentSnmpEngineIdConfigEntry 3 } agentSnmpEngineIdStatus OBJECT-TYPE SYNTAX INTEGER { active(1), create(4), destory(6) } MAX-ACCESS read-create STATUS current DESCRIPTION "The status of SNMP EngineID. active(1) - This snmp EngineID is active. create(4) - Create a new SNMP EngineID. destory(6) - Delete a SNMP EngineID." DEFVAL { active } ::= { agentSnmpEngineIdConfigEntry 4 } --************************************************************************************** -- agentSpanningTreeConfigGroup -- --************************************************************************************** agentSpanningTreeConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 7 } agentSpanningTreeMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The switch's Spanning Tree Switch Status. This functionality is now handled by agentStpAdminMode" ::= { agentSpanningTreeConfigGroup 1 } --************************************************************************************** -- agentSwitchConfigGroup -- --************************************************************************************** agentSwitchConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 8 } agentSwitchAddressAgingTimeoutTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchAddressAgingTimeoutEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The switch's address aging timeout table" ::= { agentSwitchConfigGroup 4 } agentSwitchAddressAgingTimeoutEntry OBJECT-TYPE SYNTAX AgentSwitchAddressAgingTimeoutEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Aging information about a specific Filtering Database." INDEX { dot1qFdbId } ::= { agentSwitchAddressAgingTimeoutTable 1 } AgentSwitchAddressAgingTimeoutEntry ::= SEQUENCE { agentSwitchAddressAgingTimeout Integer32 } agentSwitchAddressAgingTimeout OBJECT-TYPE SYNTAX Integer32 (10..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The FDB entry's address aging timeout (in seconds)" DEFVAL { 300 } ::= { agentSwitchAddressAgingTimeoutEntry 1 } --************************************************************************************** agentSwitchStaticMacFilteringTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchStaticMacFilteringEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The switch's static Mac filtering table" ::= { agentSwitchConfigGroup 5 } agentSwitchStaticMacFilteringEntry OBJECT-TYPE SYNTAX AgentSwitchStaticMacFilteringEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Per-port ingress/egress filter configuration based on VLAN Id and MAC address." INDEX { agentSwitchStaticMacFilteringVlanId, agentSwitchStaticMacFilteringAddress } ::= { agentSwitchStaticMacFilteringTable 1 } AgentSwitchStaticMacFilteringEntry ::= SEQUENCE { agentSwitchStaticMacFilteringVlanId Integer32, agentSwitchStaticMacFilteringAddress MacAddress, agentSwitchStaticMacFilteringSourcePortMask AgentPortMask, agentSwitchStaticMacFilteringDestPortMask AgentPortMask, agentSwitchStaticMacFilteringStatus RowStatus } agentSwitchStaticMacFilteringVlanId OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The Static MAC Filter Vlan Id" ::= { agentSwitchStaticMacFilteringEntry 1 } agentSwitchStaticMacFilteringAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Static MAC Filter MAC address" ::= { agentSwitchStaticMacFilteringEntry 2 } agentSwitchStaticMacFilteringSourcePortMask OBJECT-TYPE SYNTAX AgentPortMask MAX-ACCESS read-write STATUS current DESCRIPTION "The Static MAC Filter source port mask. When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Configuration of any port numbers between this range that are not valid ports return a failure message, but will still apply configuration for valid ports. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table." ::= { agentSwitchStaticMacFilteringEntry 3 } agentSwitchStaticMacFilteringDestPortMask OBJECT-TYPE SYNTAX AgentPortMask MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The Static MAC Filter destination port mask. When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Configuration of any port numbers between this range that are not valid ports return a failure message, but will still apply configuration for valid ports. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table. Configuring destination port mask for a unicast MAC filter is not supported on some platforms." ::= { agentSwitchStaticMacFilteringEntry 4 } agentSwitchStaticMacFilteringStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The Static MAC Filter status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry" ::= { agentSwitchStaticMacFilteringEntry 5 } --************************************************************************************** -- agentSwitchStormControlGroup -- --************************************************************************************** -- agentSwitchStormControlGroup OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 12 } -- -- -- agentSwitchDot3FlowControlMode OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Config switchconfig flowcontrol allows you to enable or disable -- 802.3x flow control for the switch. This value -- applies to only full-duplex mode ports. " -- DEFVAL { disable } -- ::= { agentSwitchStormControlGroup 1 } -- -- agentSwitchBroadcastControlMode OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The switch config broadcast allows you to enable or disable -- broadcast storm recovery mode. When you specify Enable for Broadcast -- Storm Recovery and the broadcast traffic on any Ethernet port exceeds -- the configured threshold, the switch blocks (discards) the broadcast -- traffic." -- DEFVAL { disable } -- ::= { agentSwitchStormControlGroup 4 } -- -- agentSwitchBroadcastControlThreshold OBJECT-TYPE -- SYNTAX Unsigned32(0..14880000) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Configures the broadcast storm recovery threshold for this port -- as a percentage of port speed or as an absolute pps rate." -- DEFVAL { 5 } -- ::= { agentSwitchStormControlGroup 5 } -- -- agentSwitchBroadcastControlThresholdUnit OBJECT-TYPE -- SYNTAX INTEGER { -- percent(1), -- pps(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Configures the units of the threshold value to percentage of -- port speed or absolute packets per second." -- DEFVAL { percent } -- ::= { agentSwitchStormControlGroup 10 } -- -- agentSwitchMulticastControlMode OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The switch config multicast allows you to enable or disable -- multicast storm recovery mode. When you specify Enable for multicast -- Storm Recovery and the multicast traffic on any Ethernet port exceeds -- the configured threshold, the switch blocks (discards) the multicast -- traffic." -- DEFVAL { disable } -- ::= { agentSwitchStormControlGroup 6 } -- -- agentSwitchMulticastControlThreshold OBJECT-TYPE -- SYNTAX Unsigned32(0..14880000) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Configures the multicast storm recovery threshold for this port -- as a percentage of port speed or as an absolute pps rate." -- DEFVAL { 5 } -- ::= { agentSwitchStormControlGroup 7 } -- -- agentSwitchMulticastControlThresholdUnit OBJECT-TYPE -- SYNTAX INTEGER { -- percent(1), -- pps(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Configures the units of the threshold value to percentage of -- port speed or absolute packets per second." -- DEFVAL { percent } -- ::= { agentSwitchStormControlGroup 11 } -- -- agentSwitchUnicastControlMode OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The switch config unicast allows you to enable or disable -- unicast storm recovery mode. When you specify Enable for unicast -- Storm Recovery and the unknown unicast traffic on any Ethernet port exceeds -- the configured threshold, the switch blocks (discards) the unknown unicast -- traffic." -- DEFVAL { disable } -- ::= { agentSwitchStormControlGroup 8 } -- -- agentSwitchUnicastControlThreshold OBJECT-TYPE -- SYNTAX Unsigned32(0..14880000) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Configures the unicast storm recovery threshold for this port -- as a percentage of port speed or as an absolute pps rate." -- DEFVAL { 5 } -- ::= { agentSwitchStormControlGroup 9 } -- -- agentSwitchUnicastControlThresholdUnit OBJECT-TYPE -- SYNTAX INTEGER { -- percent(1), -- pps(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Configures the units of the threshold value to percentage of -- port speed or absolute packets per second." -- DEFVAL { percent } -- ::= { agentSwitchStormControlGroup 12 } --************************************************************************************** -- agentSwitchSnoopingGroup -- --************************************************************************************** agentSwitchSnoopingGroup OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 6 } agentSwitchSnoopingCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchSnoopingCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the IGMP/MLD Snooping Global configuration entries." ::= { agentSwitchSnoopingGroup 1 } agentSwitchSnoopingCfgEntry OBJECT-TYPE SYNTAX AgentSwitchSnoopingCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents entry for Snooping switch Configuration." INDEX { agentSwitchSnoopingProtocol } ::= { agentSwitchSnoopingCfgTable 1 } AgentSwitchSnoopingCfgEntry ::= SEQUENCE { agentSwitchSnoopingProtocol InetAddressType, agentSwitchSnoopingAdminMode INTEGER, agentSwitchSnoopingPortMask AgentPortMask, agentSwitchSnoopingMulticastControlFramesProcessed Counter32 } agentSwitchSnoopingProtocol OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The protocol type of network protocol in use." ::= { agentSwitchSnoopingCfgEntry 1 } agentSwitchSnoopingAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This enables or disables Snooping on the system. " DEFVAL { disable } ::= { agentSwitchSnoopingCfgEntry 2 } agentSwitchSnoopingPortMask OBJECT-TYPE SYNTAX AgentPortMask MAX-ACCESS read-write STATUS current DESCRIPTION "IGMP/MLD Snooping Port Mask. This allows configuration of IGMP/MLD Snooping on selected ports. IGMP/MLD Snooping cannot be enabled on an interface that has routing enabled, or is a member of a LAG. If a port which has IGMP/MLD Snooping enabled becomes enabled for routing, or is enlisted as a member of a LAG, IGMP/MLD Snooping functionality will be disabled on that port. IGMP/MLD Snooping functionality will be subsequently be reenabled if routing is disabled or LAG membership is removed from an interface that had previously had IGMP/MLD Snooping enabled. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table." DEFVAL { '000000000000'H } ::= { agentSwitchSnoopingCfgEntry 3 } agentSwitchSnoopingMulticastControlFramesProcessed OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Multicast Control Frames Processed by CPU. The number of multicast control frames that have been processed by the CPU." ::= { agentSwitchSnoopingCfgEntry 4 } --************************************************************************************** -- agentSwitchSnoopingIntfGroup -- --************************************************************************************** agentSwitchSnoopingIntfGroup OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 7 } agentSwitchSnoopingIntfTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchSnoopingIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the IGMP/MLD Snooping Interface configuration entries." ::= { agentSwitchSnoopingIntfGroup 1 } agentSwitchSnoopingIntfEntry OBJECT-TYPE SYNTAX AgentSwitchSnoopingIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents entry for a IGMP/MLD Snooping Interface." INDEX { ifIndex, agentSwitchSnoopingProtocol } ::= { agentSwitchSnoopingIntfTable 1 } AgentSwitchSnoopingIntfEntry ::= SEQUENCE { agentSwitchSnoopingIntfIndex Unsigned32, agentSwitchSnoopingIntfAdminMode INTEGER, agentSwitchSnoopingIntfGroupMembershipInterval Integer32, -- georgehu 2013.10.03, Defect 120352: [MLD snooping] The max response time in global mld snooping does not work but work in vlan database command -- agentSwitchSnoopingIntfMaxResponseTime -- Integer32, agentSwitchSnoopingIntfMRPExpirationTime Integer32, agentSwitchSnoopingIntfFastLeaveAdminMode INTEGER, agentSwitchSnoopingIntfMulticastRouterMode INTEGER, agentSwitchSnoopingIntfVlanIDs VlanList } agentSwitchSnoopingIntfIndex OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The port number to be selected. Each port maps to an interface." ::= { agentSwitchSnoopingIntfEntry 1 } agentSwitchSnoopingIntfAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This enables or disables IGMP/MLD Snooping on a selected interface." DEFVAL { disable } ::= { agentSwitchSnoopingIntfEntry 2 } agentSwitchSnoopingIntfGroupMembershipInterval OBJECT-TYPE SYNTAX Integer32 (2..3600) MAX-ACCESS read-write STATUS current DESCRIPTION "The amount of time in seconds that a switch will wait for a report from a particular group on the selected interface before deleting the interface from the entry. This value must be greater than agentSwitchSnoopingIntfMaxResponseTime." DEFVAL { 260 } ::= { agentSwitchSnoopingIntfEntry 3 } -- georgehu 2013.10.03, Defect 120352: [MLD snooping] The max response time in global mld snooping does not work but work in vlan database command -- agentSwitchSnoopingIntfMaxResponseTime OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The amount of time in seconds a switch will wait after sending -- a query on the selected interface because it did not receive a report for -- a particular group in that interface. This value must be less -- than agentSwitchSnoopingIntfGroupMembershipInterval. For IGMP Snooping, -- this value ranges from 1 to 25 and for MLD Snooping, this value -- ranges from 1 to 65." -- -- DEFVAL { 10 } -- ::= { agentSwitchSnoopingIntfEntry 4 } agentSwitchSnoopingIntfMRPExpirationTime OBJECT-TYPE SYNTAX Integer32 (0..3600) MAX-ACCESS read-write STATUS current DESCRIPTION "The amount of time in seconds that a switch will wait for a query to be received on the selected interface before the interface is removed from the list of interfaces with multicast routers attached." DEFVAL { 0 } ::= { agentSwitchSnoopingIntfEntry 5 } agentSwitchSnoopingIntfFastLeaveAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This enables or disables IGMP/MLD Snooping on the selected interface." DEFVAL { disable } ::= { agentSwitchSnoopingIntfEntry 6 } agentSwitchSnoopingIntfMulticastRouterMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This enables or disables Multicast Routing on the selected interface." DEFVAL { disable } ::= { agentSwitchSnoopingIntfEntry 7 } agentSwitchSnoopingIntfVlanIDs OBJECT-TYPE SYNTAX VlanList MAX-ACCESS read-only STATUS current DESCRIPTION "This field lists all the VlanIDs which include the selected interface." ::= { agentSwitchSnoopingIntfEntry 8 } --************************************************************************************** -- agentSwitchSnoopingVlanGroup -- --************************************************************************************** agentSwitchSnoopingVlanGroup OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 8 } agentSwitchSnoopingVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchSnoopingVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the IGMP/MLD Snooping Vlan configuration entries." ::= { agentSwitchSnoopingVlanGroup 1 } agentSwitchSnoopingVlanEntry OBJECT-TYPE SYNTAX AgentSwitchSnoopingVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents entry for a IGMP/MLD Snooping Vlan." INDEX { dot1qVlanIndex, agentSwitchSnoopingProtocol } ::= { agentSwitchSnoopingVlanTable 1 } AgentSwitchSnoopingVlanEntry ::= SEQUENCE { agentSwitchSnoopingVlanAdminMode INTEGER, agentSwitchSnoopingVlanGroupMembershipInterval Integer32, agentSwitchSnoopingVlanMaxResponseTime Integer32, agentSwitchSnoopingVlanFastLeaveAdminMode INTEGER, agentSwitchSnoopingVlanMRPExpirationTime Integer32 } agentSwitchSnoopingVlanAdminMode OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This enables or disables IGMP/MLD Snooping on a selected Vlan interface." DEFVAL { disable } ::= { agentSwitchSnoopingVlanEntry 1 } agentSwitchSnoopingVlanGroupMembershipInterval OBJECT-TYPE SYNTAX Integer32 (2..3600) MAX-ACCESS read-write STATUS current DESCRIPTION "The amount of time in seconds that a switch will wait for a report from a particular group on the selected vlan before deleting the interface participating in the vlan from the entry. This value must be greater than agentSwitchSnoopingIntfMaxResponseTime." DEFVAL { 260 } ::= { agentSwitchSnoopingVlanEntry 2 } agentSwitchSnoopingVlanMaxResponseTime OBJECT-TYPE SYNTAX Integer32 (1..3599) MAX-ACCESS read-write STATUS current DESCRIPTION "The amount of time in seconds a switch will wait after sending a query on the selected vlan because it did not receive a report for a particular group in the interface participating in the vlan. This value must be less than agentSwitchSnoopingIntfGroupMembershipInterval. For IGMP Snooping, this value ranges from 1 to 25 and for MLD Snooping, this value ranges from 1 to 65." DEFVAL { 10 } ::= { agentSwitchSnoopingVlanEntry 3 } agentSwitchSnoopingVlanFastLeaveAdminMode OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This enables or disables IGMP/MLD Snooping on the selected vlan." DEFVAL { disable } ::= { agentSwitchSnoopingVlanEntry 4 } agentSwitchSnoopingVlanMRPExpirationTime OBJECT-TYPE SYNTAX Integer32 (0..3600) MAX-ACCESS read-write STATUS current DESCRIPTION "The amount of time in seconds that a switch will wait for a query to be received on the selected interface participating in the vlan before the interface is removed from the list of interfaces with multicast routers attached. This parameter is configurable only for exisiting Vlans." DEFVAL { 0 } ::= { agentSwitchSnoopingVlanEntry 5 } --************************************************************************************** -- agentSwitchVlanStaticMrouterGroup -- --************************************************************************************** agentSwitchVlanStaticMrouterGroup OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 9 } agentSwitchVlanStaticMrouterTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchVlanStaticMrouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the IGMP/MLD Static Mrouter Configuration parameters." ::= { agentSwitchVlanStaticMrouterGroup 1 } agentSwitchVlanStaticMrouterEntry OBJECT-TYPE SYNTAX AgentSwitchVlanStaticMrouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents entry for a IGMP/MLD Static Mrouter." INDEX { ifIndex, dot1qVlanIndex, agentSwitchSnoopingProtocol } ::= { agentSwitchVlanStaticMrouterTable 1 } AgentSwitchVlanStaticMrouterEntry ::= SEQUENCE { agentSwitchVlanStaticMrouterAdminMode INTEGER } agentSwitchVlanStaticMrouterAdminMode OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This enables or disables IGMP/MLD Mrouter on a per-interface per-vlan basis." DEFVAL { disable } ::= { agentSwitchVlanStaticMrouterEntry 1 } --************************************************************************************** -- agentSwitchMFDBGroup -- --************************************************************************************** agentSwitchMFDBGroup OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 10 } agentSwitchMFDBTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchMFDBEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Multicast Forwarding Database table" ::= { agentSwitchMFDBGroup 1 } agentSwitchMFDBEntry OBJECT-TYPE SYNTAX AgentSwitchMFDBEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains Forwarding and Filtering information per Vlan Index, MAC Address, and Component User." INDEX { agentSwitchMFDBVlanId, agentSwitchMFDBMacAddress, agentSwitchMFDBProtocolType, agentSwitchMFDBType } ::= { agentSwitchMFDBTable 1 } AgentSwitchMFDBEntry ::= SEQUENCE { agentSwitchMFDBVlanId VlanIndex, agentSwitchMFDBMacAddress MacAddress, agentSwitchMFDBProtocolType INTEGER, agentSwitchMFDBType INTEGER, agentSwitchMFDBDescription DisplayString, agentSwitchMFDBForwardingPortMask AgentPortMask, agentSwitchMFDBFilteringPortMask AgentPortMask } agentSwitchMFDBVlanId OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Vlan Index for which this entry is associated with." ::= { agentSwitchMFDBEntry 1 } agentSwitchMFDBMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "A multicast MAC address for which the switch has forwarding and or filtering information." ::= { agentSwitchMFDBEntry 2 } agentSwitchMFDBProtocolType OBJECT-TYPE SYNTAX INTEGER { static(1), gmrp(2), igmp(3), mld(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The component that is responsible for this entry in the Multicast Forwarding Database." ::= { agentSwitchMFDBEntry 3 } agentSwitchMFDBType OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This displays the type of the entry. static(1) - Entries configured by the end user dynamic(2) - Entries added as a result of a learning process or protocol if agentSwitchMFDBForwardingPortMask is all zero means there is no such agentSwitchMFDBType assigned forwarding port." ::= { agentSwitchMFDBEntry 4 } agentSwitchMFDBDescription OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Text description of this multicast table entry." ::= { agentSwitchMFDBEntry 5 } agentSwitchMFDBForwardingPortMask OBJECT-TYPE SYNTAX AgentPortMask MAX-ACCESS read-only STATUS current DESCRIPTION "BitMask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table." ::= { agentSwitchMFDBEntry 6 } agentSwitchMFDBFilteringPortMask OBJECT-TYPE SYNTAX AgentPortMask MAX-ACCESS read-only STATUS current DESCRIPTION "BitMask indicating which ports this entry indicates should be filtered. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table." ::= { agentSwitchMFDBEntry 7 } --************************************************************************************** agentSwitchMFDBSummaryTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchMFDBSummaryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Multicast Forwarding Database Summary table" ::= { agentSwitchMFDBGroup 2 } agentSwitchMFDBSummaryEntry OBJECT-TYPE SYNTAX AgentSwitchMFDBSummaryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Summarizes the forwarding ports for all components registered for all MFDB table entries with the same Vlan Index and MAC Address." INDEX { agentSwitchMFDBSummaryVlanId, agentSwitchMFDBSummaryMacAddress } ::= { agentSwitchMFDBSummaryTable 1 } AgentSwitchMFDBSummaryEntry ::= SEQUENCE { agentSwitchMFDBSummaryVlanId VlanIndex, agentSwitchMFDBSummaryMacAddress MacAddress, agentSwitchMFDBSummaryForwardingPortMask AgentPortMask } agentSwitchMFDBSummaryVlanId OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Vlan Index for which this entry is associated with." ::= { agentSwitchMFDBSummaryEntry 1 } agentSwitchMFDBSummaryMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "A multicast MAC address for which the switch has forwarding and or filtering information." ::= { agentSwitchMFDBSummaryEntry 2 } agentSwitchMFDBSummaryForwardingPortMask OBJECT-TYPE SYNTAX AgentPortMask MAX-ACCESS read-only STATUS current DESCRIPTION "Port Mask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table." ::= { agentSwitchMFDBSummaryEntry 3 } --************************************************************************************** agentSwitchMFDBMaxTableEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This displays the maximum number of entries that can possibly be in the Multicast Forwarding Database table." ::= { agentSwitchMFDBGroup 3 } agentSwitchMFDBMostEntriesUsed OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This displays the largest number of entries that have been present in the Multicast Forwarding Database table. This value is also known as the MFDB high-water mark." ::= { agentSwitchMFDBGroup 4 } agentSwitchMFDBCurrentEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This displays the current number of entries in the Multicast Forwarding Database table." ::= { agentSwitchMFDBGroup 5 } --************************************************************************************** -- agentSwitchDVlanTagGroup -- --************************************************************************************** agentSwitchDVlanTagGroup OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 11 } agentSwitchDVlanTagEthertype OBJECT-TYPE SYNTAX Integer32 (1..65535) -- 0x0001..0xFFFF MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Configures the Double Vlan Tag Ethertype for the switch. If this object is supported, ethertype cannot be configured per port. Commonly used are the Ethertypes for vman tags (34984, or 0x88A8) and dot1q tags (33024, or 0x8100)." ::= { agentSwitchDVlanTagGroup 1 } agentSwitchDVlanTagTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchDVlanTagEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "A table of entries specifying the ethertype (TPID) values. This will let the user specify multiple ethertypes globally." ::= { agentSwitchDVlanTagGroup 2 } agentSwitchDVlanTagEntry OBJECT-TYPE SYNTAX AgentSwitchDVlanTagEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "A table entry specifying the ethertype (TPID) values. Commonly used are the Ethertypes for vman tags (34984, or 0x88A8) and dot1q tags (33024, or 0x8100)." INDEX { agentSwitchDVlanTagTPid } ::= { agentSwitchDVlanTagTable 1 } AgentSwitchDVlanTagEntry ::= SEQUENCE { agentSwitchDVlanTagTPid Integer32, agentSwitchDVlanTagPrimaryTPid INTEGER, agentSwitchDVlanTagRowStatus RowStatus } agentSwitchDVlanTagTPid OBJECT-TYPE SYNTAX Integer32 (1..65535) -- 0x0001..0xFFFF MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "Ethertype value to identify incoming double tagged frames" ::= { agentSwitchDVlanTagEntry 1 } agentSwitchDVlanTagPrimaryTPid OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-create STATUS obsolete DESCRIPTION "Specifies if this TPID is primary TPID for the switch or not" ::= { agentSwitchDVlanTagEntry 2} agentSwitchDVlanTagRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS obsolete DESCRIPTION "Row status" ::= { agentSwitchDVlanTagEntry 3} agentSwitchPortDVlanTagTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchPortDVlanTagEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "A table entries specifying the ethertype (TPID) values per port." ::= { agentSwitchDVlanTagGroup 3 } agentSwitchPortDVlanTagEntry OBJECT-TYPE SYNTAX AgentSwitchPortDVlanTagEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "A table entry specifying the ethertype (TPID) value for a port." INDEX { agentSwitchPortDVlanTagInterfaceIfIndex, agentSwitchPortDVlanTagTPid } ::= { agentSwitchPortDVlanTagTable 1 } AgentSwitchPortDVlanTagEntry ::= SEQUENCE { agentSwitchPortDVlanTagInterfaceIfIndex Integer32, agentSwitchPortDVlanTagTPid Integer32, agentSwitchPortDVlanTagMode INTEGER, agentSwitchPortDVlanTagCustomerId Integer32, agentSwitchPortDVlanTagRowStatus RowStatus } agentSwitchPortDVlanTagInterfaceIfIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "Port Id on to which the Ethertype value is mapped" ::= { agentSwitchPortDVlanTagEntry 1 } agentSwitchPortDVlanTagTPid OBJECT-TYPE SYNTAX Integer32 (1..65535) -- 0x0001..0xFFFF MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "Ethertype value to identify incoming double tagged frames" ::= { agentSwitchPortDVlanTagEntry 2 } agentSwitchPortDVlanTagMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS obsolete DESCRIPTION "Controls the Double Vlan Tag mode on this port." ::= { agentSwitchPortDVlanTagEntry 3} agentSwitchPortDVlanTagCustomerId OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-create STATUS obsolete DESCRIPTION "Configures the Customer ID for the Double Vlan Tag for this port." ::= { agentSwitchPortDVlanTagEntry 4 } agentSwitchPortDVlanTagRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS obsolete DESCRIPTION "Row status" ::= { agentSwitchPortDVlanTagEntry 5} agentSwitchIfDVlanTagTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchIfDVlanTagEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table entries specifying the ethertype (TPID) values per interface." ::= { agentSwitchDVlanTagGroup 4 } agentSwitchIfDVlanTagEntry OBJECT-TYPE SYNTAX AgentSwitchIfDVlanTagEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table entry specifying the ethertype (TPID) value for a interface." INDEX { agentSwitchIfDVlanTagIfIndex } ::= { agentSwitchIfDVlanTagTable 1 } AgentSwitchIfDVlanTagEntry ::= SEQUENCE { agentSwitchIfDVlanTagIfIndex Integer32, agentSwitchIfDVlanTagMode INTEGER, agentSwitchIfDVlanTagTPid Integer32 } agentSwitchIfDVlanTagIfIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Interface Id on to which the Ethertype value is mapped" ::= { agentSwitchIfDVlanTagEntry 1 } agentSwitchIfDVlanTagMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Controls the Double Vlan Tag mode on this interface." ::= { agentSwitchIfDVlanTagEntry 2 } agentSwitchIfDVlanTagTPid OBJECT-TYPE SYNTAX Integer32 (1..65535) -- 0x0001..0xFFFF MAX-ACCESS read-write STATUS current DESCRIPTION "Ethertype value to identify incoming double tagged frames. Commonly used are the Ethertypes for vman tags (34984, or 0x88A8) and dot1q tags (33024, or 0x8100)." ::= { agentSwitchIfDVlanTagEntry 3 } --************************************************************************************** -- agentSwitchVlanMacAssociationGroup -- --************************************************************************************** agentSwitchVlanMacAssociationGroup OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 17 } agentSwitchVlanMacAssociationTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchVlanMacAssociationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The switch's MAC To VLAN association table" ::= { agentSwitchVlanMacAssociationGroup 1 } agentSwitchVlanMacAssociationEntry OBJECT-TYPE SYNTAX AgentSwitchVlanMacAssociationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "VLAN to be assigned to untagged or priority tagged packets based on MAC address." INDEX { agentSwitchVlanMacAssociationMacAddress,agentSwitchVlanMacAssociationVlanId,agentSwitchVlanMacAssociationPriority } ::= { agentSwitchVlanMacAssociationTable 1 } AgentSwitchVlanMacAssociationEntry ::= SEQUENCE { agentSwitchVlanMacAssociationMacAddress MacAddress, agentSwitchVlanMacAssociationVlanId VlanIndex, agentSwitchVlanMacAssociationPriority Unsigned32, agentSwitchVlanMacAssociationRowStatus RowStatus } agentSwitchVlanMacAssociationMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Mac address" ::= { agentSwitchVlanMacAssociationEntry 1 } agentSwitchVlanMacAssociationVlanId OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN the Mac address assigned to" ::= { agentSwitchVlanMacAssociationEntry 2 } agentSwitchVlanMacAssociationPriority OBJECT-TYPE SYNTAX Unsigned32 (0..7) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Priority of mac base vlan" ::= { agentSwitchVlanMacAssociationEntry 4 } agentSwitchVlanMacAssociationRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The Mac to VLAN association row status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry" ::= { agentSwitchVlanMacAssociationEntry 3 } --************************************************************************************** -- agentSwitchProtectedPortGroup -- --************************************************************************************** agentSwitchProtectedPortConfigGroup OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 18 } agentSwitchProtectedPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchProtectedPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The switch's protected port mapping table" ::= { agentSwitchProtectedPortConfigGroup 1 } agentSwitchProtectedPortEntry OBJECT-TYPE SYNTAX AgentSwitchProtectedPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Protected ports assigned to groups." INDEX { agentSwitchProtectedPortGroupId } ::= { agentSwitchProtectedPortTable 1 } AgentSwitchProtectedPortEntry ::= SEQUENCE { agentSwitchProtectedPortGroupId Integer32, agentSwitchProtectedPortGroupName DisplayString, agentSwitchProtectedPortPortList PortList } agentSwitchProtectedPortGroupId OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The group that this port belongs to" ::= { agentSwitchProtectedPortEntry 1 } agentSwitchProtectedPortGroupName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The name of the group" ::= { agentSwitchProtectedPortEntry 2 } agentSwitchProtectedPortPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "The set of ports that are protected in this group" ::= { agentSwitchProtectedPortEntry 3 } --************************************************************************************** -- agentSwitchVlanSubnetAssociationGroup -- --************************************************************************************** agentSwitchVlanSubnetAssociationGroup OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 19 } agentSwitchVlanSubnetAssociationTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchVlanSubnetAssociationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The switch's Subnet To VLAN association table" ::= { agentSwitchVlanSubnetAssociationGroup 1 } agentSwitchVlanSubnetAssociationEntry OBJECT-TYPE SYNTAX AgentSwitchVlanSubnetAssociationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "VLAN to be assigned to untagged or priority tagged packets based on IP address and Subnet Mask." INDEX { agentSwitchVlanSubnetAssociationIPAddress,agentSwitchVlanSubnetAssociationSubnetMask,agentSwitchVlanSubnetAssociationVlanId,agentSwitchVlanSubnetAssociationPriority} ::= { agentSwitchVlanSubnetAssociationTable 1 } AgentSwitchVlanSubnetAssociationEntry ::= SEQUENCE { agentSwitchVlanSubnetAssociationIPAddress IpAddress, agentSwitchVlanSubnetAssociationSubnetMask IpAddress, agentSwitchVlanSubnetAssociationVlanId VlanIndex, agentSwitchVlanSubnetAssociationPriority Unsigned32, agentSwitchVlanSubnetAssociationRowStatus RowStatus } agentSwitchVlanSubnetAssociationIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ip address" ::= { agentSwitchVlanSubnetAssociationEntry 1 } agentSwitchVlanSubnetAssociationSubnetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The subnet mask" ::= { agentSwitchVlanSubnetAssociationEntry 2 } agentSwitchVlanSubnetAssociationVlanId OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN that the IP address and subnet mask assigned to" ::= { agentSwitchVlanSubnetAssociationEntry 3 } agentSwitchVlanSubnetAssociationPriority OBJECT-TYPE SYNTAX Unsigned32 (0..7) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Priority that the IP address and subnet mask assigned to" ::= { agentSwitchVlanSubnetAssociationEntry 5 } agentSwitchVlanSubnetAssociationRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The Subnet to VLAN association row status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry" ::= { agentSwitchVlanSubnetAssociationEntry 4 } --************************************************************************************** -- agentSwitchSnoopingQuerierGroup -- --************************************************************************************** agentSwitchSnoopingQuerierGroup OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 20 } agentSwitchSnoopingQuerierCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchSnoopingQuerierCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the IGMP/MLD Snooping Querier Global configuration entries." ::= { agentSwitchSnoopingQuerierGroup 1 } agentSwitchSnoopingQuerierCfgEntry OBJECT-TYPE SYNTAX AgentSwitchSnoopingQuerierCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents entry for Snooping Querier Configuration." INDEX { agentSwitchSnoopingProtocol } ::= { agentSwitchSnoopingQuerierCfgTable 1 } AgentSwitchSnoopingQuerierCfgEntry ::= SEQUENCE { agentSwitchSnoopingQuerierAdminMode INTEGER, agentSwitchSnoopingQuerierVersion Integer32, agentSwitchSnoopingQuerierAddress InetAddress, agentSwitchSnoopingQuerierQueryInterval Integer32, agentSwitchSnoopingQuerierExpiryInterval Integer32 } agentSwitchSnoopingQuerierAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This enables or disables Snooping Querier on the system. " DEFVAL { disable } ::= { agentSwitchSnoopingQuerierCfgEntry 1 } agentSwitchSnoopingQuerierVersion OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the multicast protocol versions that are supported by the system." ::= { agentSwitchSnoopingQuerierCfgEntry 2 } agentSwitchSnoopingQuerierAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the default source ip address to be used while generating general queries." ::= { agentSwitchSnoopingQuerierCfgEntry 3 } agentSwitchSnoopingQuerierQueryInterval OBJECT-TYPE SYNTAX Integer32 (1..1800) MAX-ACCESS read-write STATUS current DESCRIPTION "This specified the timer interval after which the system generates general queries." DEFVAL { 60 } ::= { agentSwitchSnoopingQuerierCfgEntry 4 } agentSwitchSnoopingQuerierExpiryInterval OBJECT-TYPE SYNTAX Integer32 (60..300) MAX-ACCESS read-write STATUS current DESCRIPTION "This specified the timer interval after which the detected other querier information is no longer valid." DEFVAL { 120 } ::= { agentSwitchSnoopingQuerierCfgEntry 5 } --************************************************************************************** -- agentSwitchSnoopingQuerierVlanCfgTable -- --************************************************************************************** agentSwitchSnoopingQuerierVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchSnoopingQuerierVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the Snooping Querier Vlan configuration entries." ::= { agentSwitchSnoopingQuerierGroup 2 } agentSwitchSnoopingQuerierVlanEntry OBJECT-TYPE SYNTAX AgentSwitchSnoopingQuerierVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents entry for a Snooping Querier configurable Vlan." INDEX { dot1qVlanIndex, agentSwitchSnoopingProtocol } ::= { agentSwitchSnoopingQuerierVlanTable 1 } AgentSwitchSnoopingQuerierVlanEntry ::= SEQUENCE { agentSwitchSnoopingQuerierVlanAdminMode INTEGER, agentSwitchSnoopingQuerierVlanOperMode INTEGER, agentSwitchSnoopingQuerierElectionParticipateMode INTEGER, agentSwitchSnoopingQuerierVlanAddress InetAddress, agentSwitchSnoopingQuerierOperVersion Integer32, agentSwitchSnoopingQuerierOperMaxResponseTime Integer32, agentSwitchSnoopingQuerierLastQuerierAddress InetAddress, agentSwitchSnoopingQuerierLastQuerierVersion Integer32 } agentSwitchSnoopingQuerierVlanAdminMode OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This enables or disables Snooping Querier on a selected Vlan interface." DEFVAL { disable } ::= { agentSwitchSnoopingQuerierVlanEntry 1 } agentSwitchSnoopingQuerierVlanOperMode OBJECT-TYPE SYNTAX INTEGER { disabled(0), querier(1), non-querier(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies the current state of the Snooping Querier on a selected vlan interface" DEFVAL { disabled } ::= { agentSwitchSnoopingQuerierVlanEntry 2 } agentSwitchSnoopingQuerierElectionParticipateMode OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This enables or disables the Snooping Querier Election Participation mode. When enabled snooping querier switch will participate in querier election up on discovering another querier in the specified vlan. When disabled, up on discovering another querier, snooping querier moves to non-querier state." DEFVAL { disable } ::= { agentSwitchSnoopingQuerierVlanEntry 3 } agentSwitchSnoopingQuerierVlanAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the default source ip address to be used while generating general queries on the specified vlan." ::= { agentSwitchSnoopingQuerierVlanEntry 4 } agentSwitchSnoopingQuerierOperVersion OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies the multicast protocol version that is currently being used by the snooping switch for the specified vlan while generating query messages." ::= { agentSwitchSnoopingQuerierVlanEntry 5 } agentSwitchSnoopingQuerierOperMaxResponseTime OBJECT-TYPE SYNTAX Integer32(-1|0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time in seconds a switch will wait after sending a query on the selected vlan because it did not receive a report for a particular group in the interface participating in the vlan. This object is valid only when agentSwitchSnoopingQuerierOperVersion object is valid. (-1) - indicates that parameter is not available; ( 0) - indicates that response time is less then 1 second." ::= { agentSwitchSnoopingQuerierVlanEntry 6 } agentSwitchSnoopingQuerierLastQuerierAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies the last querier's ip address for the specified vlan. It represents the detected other multicast querier in the vlan. " ::= { agentSwitchSnoopingQuerierVlanEntry 7 } agentSwitchSnoopingQuerierLastQuerierVersion OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies the multicast protocol version that is currently being used by the detected other multicast querier for the specified vlan. (-1) - indicates that parameter is not available." ::= { agentSwitchSnoopingQuerierVlanEntry 8 } --************************************************************************************** -- agentTransferConfigGroup -- --************************************************************************************** agentTransferConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 9 } --************************************************************************************** -- agentTransferUploadGroup -- --************************************************************************************** agentTransferUploadGroup OBJECT IDENTIFIER ::= { agentTransferConfigGroup 1 } agentTransferUploadMode OBJECT-TYPE SYNTAX INTEGER { tftp(1), sftp(5), scp(6), ftp(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer upload mode configures the mode to use when uploading from the switch. The mode is either TFTP, FTP, SFTP or SCP. SFTP and SCP are only allowed if the SSH feature is present. " ::= { agentTransferUploadGroup 1 } agentTransferUploadPath OBJECT-TYPE SYNTAX DisplayString (SIZE(0..160)) MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer upload path configures the directory path where the file is to be uploaded to. The switch remembers the last file path used. " ::= { agentTransferUploadGroup 3 } agentTransferUploadFilename OBJECT-TYPE SYNTAX DisplayString (SIZE(0..30)) MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer upload filename configures the file name for the file being uploaded from the switch. It can be up to 30 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 17 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr. Note: File Name, File Path, and Server IP Address are applicable only if the Transfer Mode is TFTP, FTP, SFTP or SCP." ::= { agentTransferUploadGroup 4 } agentTransferUploadScriptFromSwitchSrcFilename OBJECT-TYPE SYNTAX DisplayString (SIZE(0..30)) MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer upload filename configures the file name for the file being uploaded from the switch. It can be up to 30 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 17 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr. Note: File Name, File Path, and Server IP Address are applicable only if the Transfer Mode is TFTP, FTP, SFTP or SCP. The file extension of transfer upload script filename must be '.scr'." ::= { agentTransferUploadGroup 5 } agentTransferUploadStartupConfigFromSwitchSrcFilename OBJECT-TYPE SYNTAX DisplayString (SIZE(0..30)) MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer upload filename configures the file name for the file being uploaded from the switch. It can be up to 30 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 17 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr. Note: File Name, File Path, and Server IP Address are applicable only if the Transfer Mode is TFTP, FTP, SFTP or SCP." ::= { agentTransferUploadGroup 6 } agentTransferUploadOpCodeFromSwitchSrcFilename OBJECT-TYPE SYNTAX DisplayString (SIZE(0..30)) MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer upload filename configures the file name for the file being uploaded from the switch. It can be up to 30 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 17 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr. Note: File Name, File Path, and Server IP Address are applicable only if the Transfer Mode is TFTP, FTP, SFTP or SCP." ::= { agentTransferUploadGroup 7 } agentTransferUploadDataType OBJECT-TYPE SYNTAX INTEGER { script(1), code(2), config(3), errorlog(4), messagelog(5), traplog(6), clibanner(7), vmtracer(8), runningConfig(9) } MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer upload datatype configures the type of file to upload from the switch. The types for upload are: - Script - Code - Configuration File - Error log - Message log - Trap log - Banner File - VMTracer Image File - Running Configuration " ::= { agentTransferUploadGroup 8 } agentTransferUploadStart OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer upload start will start an upload transfer." ::= { agentTransferUploadGroup 9 } agentTransferUploadStatus OBJECT-TYPE SYNTAX INTEGER { notInitiated(1), transferStarting(2), errorStarting(3), wrongFileType(4), updatingConfig(5), invalidConfigFile(6), writingToFlash(7), failureWritingToFlash(8), checkingCRC(9), failedCRC(10), unknownDirection(11), transferSuccessful(12), transferFailed(13), fileNotExist(14), runByOtherUsers(15) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the current status of an upload transfer." ::= { agentTransferUploadGroup 10 } -- agentTransferUploadServerAddressType OBJECT-TYPE -- SYNTAX InetAddressType -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The type of the serverip address, as defined in the InetAddress MIB. -- -- The agentTransferUploadServerAddress object is intepreted within the -- context of agentTransferUploadServerAddressType" -- REFERENCE "RFC 3291" -- ::= { agentTransferUploadGroup 11 } agentTransferUploadServerAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer upload serverip configures the IP address of the server where the file is to be uploaded to.It is valid only when the Transfer Mode is TFTP, FTP, SFTP or SCP. The type of this address is determined by the value of the agentTransferUploadServerAddressType object. The values for agentTransferUploadServerAddressType and agentTransferUploadServerAddress must be consistent." REFERENCE "RFC 3291" ::= { agentTransferUploadGroup 12 } -- agentTransferUploadImagename OBJECT-TYPE -- SYNTAX INTEGER { -- unknown(1), -- image1(2), -- image2(3) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Transfer upload image name. Sets the image to be uploaded as the specified -- name. Imagename cannot be set to unknown(1) option. When no name is set -- this object returns unknown(1) by default. -- Note: Imagename, File Name, File Path, and Server IP Address are applicable -- only if the Transfer Mode is TFTP, SFTP or SCP." -- -- ::= { agentTransferUploadGroup 13 } agentTransferUploadUsername OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "Username applicable only to secure upload types. Note: User Account is applicable only if the Transfer Mode is FTP, SFTP or SCP." ::= { agentTransferUploadGroup 14 } agentTransferUploadPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "Password applicable only to secure upload types. Note: User Password is applicable only if the Transfer Mode is FTP, SFTP or SCP." ::= { agentTransferUploadGroup 15 } --************************************************************************************** -- agentTransferDownloadGroup -- --************************************************************************************** agentTransferDownloadGroup OBJECT IDENTIFIER ::= { agentTransferConfigGroup 2 } agentTransferDownloadMode OBJECT-TYPE SYNTAX INTEGER { tftp(1), sftp(5), scp(6), ftp(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer download mode configures the mode to use when downloading to the switch. The mode is either TFTP, FTP, SFTP or SCP. SFTP and SCP are only allowed if the SSH feature is present. " ::= { agentTransferDownloadGroup 1 } agentTransferDownloadPath OBJECT-TYPE SYNTAX DisplayString (SIZE(0..160)) MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer download path configures the directory path where the file is located. The switch remembers the last file path used. " ::= { agentTransferDownloadGroup 3 } agentTransferDownloadFilename OBJECT-TYPE SYNTAX DisplayString (SIZE(0..30)) MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer download filename configures the file name for the file being downloaded to the switch. It can be up to 30 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 33 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr. Note: File Name, File Path, and Server IP Address are applicable only if the Transfer Mode is TFTP, FTP, SFTP or SCP." ::= { agentTransferDownloadGroup 4 } agentTransferDownloadScriptToSwitchDestFilename OBJECT-TYPE SYNTAX DisplayString (SIZE(0..30)) MAX-ACCESS read-write STATUS current DESCRIPTION "The filename used to store current Script in the switch. It can be up to 30 alphanumeric characters. The file extension of transfer download script filename must be '.scr'" ::= { agentTransferDownloadGroup 5 } agentTransferDownloadOPCodeToSwitchDestFilename OBJECT-TYPE SYNTAX DisplayString (SIZE(0..30)) MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer download tftpfilename configures the file name for the file stored in the switch. It can be up to 30 alphanumeric characters." ::= { agentTransferDownloadGroup 6 } agentTransferDownloadStartupConfigToSwitchDestFilename OBJECT-TYPE SYNTAX DisplayString (SIZE(0..30)) MAX-ACCESS read-write STATUS current DESCRIPTION "The filename used to store current Startup config in the switch. It can be up to 30 alphanumeric characters." ::= { agentTransferDownloadGroup 7 } agentTransferDownloadDataType OBJECT-TYPE SYNTAX INTEGER { script(1), code(2), config(3), sshkey-rsa1(4), sshkey-rsa2(5), sshkey-dsa(6), sslpem-root(7), sslpem-server(8), sslpem-dhweak(9), sslpem-dhstrong(10), clibanner(11), vmtracer(12), license(13) } MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer download datatype configures the type of file to download to the switch. The types for download are: script - Script File code - Code File config - Configuration File sshkey-rsa1 - SSH-1 RSA Key File sshkey-rsa2 - SSH-2 RSA Key PEM File sshkey-dsa - SSH-2 DSA Key PEM File sslpem-root - SSL Trusted Root Certificate PEM File sslpem-server - SSL Server Certificate PEM File sslpem-dhweak - SSL DH Weak Encryption Parameter PEM File sslpem-dhstrong - SSL DH Strong Encryption Parameter PEM File cli-banner - CLI Banner File vmtracer - VMTracer Image File license - License Key File Note: SSH Key files can only be downloaded if SSH Server is administratively disabled, and there are no active SSH sessions. " ::= { agentTransferDownloadGroup 8 } agentTransferDownloadStart OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer download start will start an download transfer." ::= { agentTransferDownloadGroup 9 } agentTransferDownloadStatus OBJECT-TYPE SYNTAX INTEGER { notInitiated(1), transferStarting(2), errorStarting(3), wrongFileType(4), updatingConfig(5), invalidConfigFile(6), writingToFlash(7), failureWritingToFlash(8), checkingCRC(9), failedCRC(10), unknownDirection(11), transferSuccessful(12), transferFailed(13), fileExist(14), noPartitionTableEntry(15), runByOtherUsers(16) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the current status of an download transfer." ::= { agentTransferDownloadGroup 10 } -- agentTransferDownloadServerAddressType OBJECT-TYPE -- SYNTAX InetAddressType -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The type of the serverip address, as defined in the InetAddress MIB. -- -- The agentTransferDownloadServerAddress object is intepreted within the -- context of agentTransferDownloadServerAddressType" -- REFERENCE "RFC 3291" -- ::= { agentTransferDownloadGroup 11 } agentTransferDownloadServerAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Transfer download serverip configures the IP address of the server where the file is to be downloaded from.It is valid only when the Transfer Mode is TFTP, FTP, SFTP or SCP. The type of this address is determined by the value of the agentTransferDownloadServerAddressType object. The values for agentTransferDownloadServerAddressType and agentTransferDownloadServerAddress must be consistent." REFERENCE "RFC 3291" ::= { agentTransferDownloadGroup 12 } -- agentTransferDownloadImagename OBJECT-TYPE -- SYNTAX INTEGER { -- unknown(1), -- image1(2), -- image2(3) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Transfer download image name. Sets the downloaded image as the specified -- name. Imagename cannot be set to unknown(1) option. When no name is set -- this object returns unknown(1) by default. -- Note: Imagename, File Name, File Path, and Server IP Address are applicable -- only if the Transfer Mode is TFTP, SFTP or SCP." -- -- ::= { agentTransferDownloadGroup 13 } agentTransferDownloadUsername OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "Username applicable only to secure download types. Note: User Account is applicable only if the Transfer Mode is FTP, SFTP or SCP." ::= { agentTransferDownloadGroup 14 } agentTransferDownloadPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "Password applicable only to secure download types. Note: User Password is applicable only if the Transfer Mode is FTP, SFTP or SCP." ::= { agentTransferDownloadGroup 15 } --*** switchimage starts *** --************************************************************************************** -- agentImageConfigGroup -- --************************************************************************************** agentImageConfigGroup OBJECT IDENTIFIER ::= { agentTransferConfigGroup 3 } agentImage1 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The image1 filename and software version." ::= { agentImageConfigGroup 1 } agentImage2 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The image2 filename and software version." ::= { agentImageConfigGroup 2 } agentActiveImage OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The active image name. image1 or image2." ::= { agentImageConfigGroup 3 } agentNextActiveImage OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The next active image name. user assigns either image1 or image2. " ::= { agentImageConfigGroup 4 } --*** switchimage ends *** --************************************************************************************** -- agentPortMirroringGroup --************************************************************************************** agentPortMirroringGroup OBJECT IDENTIFIER ::= { agentConfigGroup 10 } -- agentMirroredPortIfIndex OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-write -- STATUS obsolete -- DESCRIPTION -- "IfIndex of the mirrored port" -- DEFVAL { 0 } -- ::= { agentPortMirroringGroup 1 } -- -- agentProbePortIfIndex OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-write -- STATUS obsolete -- DESCRIPTION -- "IfIndex of the probe port" -- DEFVAL { 0 } -- ::= { agentPortMirroringGroup 2 } -- -- agentPortMirroringMode OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2), -- delete(3) -- } -- MAX-ACCESS read-write -- STATUS obsolete -- DESCRIPTION -- "Port mirroring mode: -- -- enable - enable mirroring mode -- disable - disable mirroring mode -- delete - clear MirroredPort and Probe Port configuration" -- DEFVAL { disable } -- ::= { agentPortMirroringGroup 3 } --************************************************************************************** -- agentPortMirroringGroup --************************************************************************************** agentPortMirrorTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentPortMirrorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes entries for each Port Mirroring session." ::= { agentPortMirroringGroup 4 } agentPortMirrorEntry OBJECT-TYPE SYNTAX AgentPortMirrorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Provides configuration of a Port Mirroring session specifying the destination port, and the source Port Mask, providing a many-to-one mapping." INDEX { agentPortMirrorSessionNum } ::= { agentPortMirrorTable 1 } AgentPortMirrorEntry ::= SEQUENCE { agentPortMirrorSessionNum Unsigned32, agentPortMirrorDestinationPort Unsigned32, agentPortMirrorSourcePortMask AgentPortMask, agentPortMirrorAdminMode INTEGER } agentPortMirrorSessionNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Session number of this mirroring entry. The number of sessions is fixed, and is platform dependant." ::= { agentPortMirrorEntry 1 } agentPortMirrorDestinationPort OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The port which traffic from the mirrored ports will be sent to." ::= { agentPortMirrorEntry 2 } agentPortMirrorSourcePortMask OBJECT-TYPE SYNTAX AgentPortMask MAX-ACCESS read-write STATUS current DESCRIPTION "The ports from which traffic will be sent to the destination port. The destination port can not be included in this list of ports." ::= { agentPortMirrorEntry 3 } agentPortMirrorAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2), delete(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The status of this port mirroring session. enable(1) - This session is active and all traffic from the source ports will be mirrored to the destination port. disable(2) - This session is not active. delete(3) - Remove the configuration for this Session" ::= { agentPortMirrorEntry 4 } agentPortMirrorTypeTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentPortMirrorTypeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes entries for each source port's direction of port mirroring." ::= { agentPortMirroringGroup 5 } agentPortMirrorTypeEntry OBJECT-TYPE SYNTAX AgentPortMirrorTypeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Provides configuration of a Port Mirroring direction specifying the session of the port mirroring and source port" INDEX { agentPortMirrorSessionNum, agentPortMirrorTypeSourcePort } ::= { agentPortMirrorTypeTable 1 } AgentPortMirrorTypeEntry ::= SEQUENCE { agentPortMirrorTypeSourcePort Unsigned32, agentPortMirrorTypeType INTEGER } agentPortMirrorTypeSourcePort OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port from which traffic will be sent to the destination port. This port should be a source port in the corresponding session" ::= { agentPortMirrorTypeEntry 1 } agentPortMirrorTypeType OBJECT-TYPE SYNTAX INTEGER { tx(1), rx(2), txrx(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The direction of the data to be mirrored on this source port. tx(1) - The data that is transmitted from the source port. rx(2) - The data that is received on the source port. txrx(3) - The data that is transmitted/received from/on the source port" DEFVAL { txrx } ::= { agentPortMirrorTypeEntry 2 } --************************************************************************************** -- agentDot3adAggPortTable --************************************************************************************** agentDot3adAggPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDot3adAggPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides 802.3ad link aggregation information for each physical port that is not available through the standard MIB." ::= { agentConfigGroup 12 } agentDot3adAggPortEntry OBJECT-TYPE SYNTAX AgentDot3adAggPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a table entry. The agentDot3adAggPort identifies the external interface number of the port." INDEX { agentDot3adAggPort } ::= { agentDot3adAggPortTable 1 } AgentDot3adAggPortEntry ::= SEQUENCE { agentDot3adAggPort Integer32, agentDot3adAggPortLACPMode INTEGER } agentDot3adAggPort OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "ifIndex of this physical port" ::= { agentDot3adAggPortEntry 1 } agentDot3adAggPortLACPMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable 802.3ad LACP on this port" ::= { agentDot3adAggPortEntry 2 } --************************************************************************************** -- agentPortConfigTable -- --************************************************************************************** agentPortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the switch's physical port config entries" ::= { agentConfigGroup 13 } agentPortConfigEntry OBJECT-TYPE SYNTAX AgentPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's physical port config entry" INDEX { agentPortDot1dBasePort } ::= { agentPortConfigTable 1 } AgentPortConfigEntry ::= SEQUENCE { agentPortDot1dBasePort Integer32, agentPortIfIndex Integer32, agentPortIanaType IANAifType, agentPortSTPMode INTEGER, agentPortSTPState INTEGER, agentPortAdminMode INTEGER, -- agentPortPhysicalMode -- INTEGER, -- agentPortPhysicalStatus -- INTEGER, agentPortLinkTrapMode INTEGER, agentPortClearStats INTEGER, agentPortDefaultType OBJECT IDENTIFIER, agentPortType OBJECT IDENTIFIER, agentPortAutoNegAdminStatus INTEGER, -- agentPortDot3FlowControlMode -- INTEGER, -- agentPortDVlanTagMode -- INTEGER, -- agentPortDVlanTagEthertype -- Integer32, -- agentPortDVlanTagCustomerId -- Integer32, agentPortMaxFrameSizeLimit Integer32, agentPortMaxFrameSize Integer32, agentPortCapability Integer32, -- agentPortBroadcastControlMode -- INTEGER, -- agentPortBroadcastControlThreshold -- Integer32, -- agentPortMulticastControlMode -- INTEGER, -- agentPortMulticastControlThreshold -- Integer32, -- agentPortUnicastControlMode -- INTEGER, -- agentPortUnicastControlThreshold -- Integer32, agentPortBroadcastControlThresholdUnit INTEGER, agentPortMulticastControlThresholdUnit INTEGER, agentPortUnicastControlThresholdUnit INTEGER, agentPortVoiceVlanMode INTEGER, agentPortVoiceVlanID Integer32, agentPortVoiceVlanPriority INTEGER, agentPortVoiceVlanDataPriorityMode INTEGER, agentPortVoiceVlanOperationalStatus INTEGER, agentPortVoiceVlanUntagged INTEGER, agentPortVoiceVlanNoneMode INTEGER, agentPortVoiceVlanAuthMode INTEGER, agentPortDot3FlowControlOperStatus INTEGER , agentPortLoadStatsInterval Integer32 } agentPortDot1dBasePort OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The port number of this port." ::= { agentPortConfigEntry 1 } agentPortIfIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Port IfIndex" ::= { agentPortConfigEntry 2 } agentPortIanaType OBJECT-TYPE SYNTAX IANAifType MAX-ACCESS read-only STATUS current DESCRIPTION "The switch's Port Type" ::= { agentPortConfigEntry 3 } agentPortSTPMode OBJECT-TYPE SYNTAX INTEGER { dot1d(1), fast(2), off(3) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The switch's Port Spanning Tree Protocol Mode STP mode values are: dot1d (the default) fast, indicates you want to use the fast spanning tree mode off, indicates the STP mode is turned off for a particular port This object is only supported when the Dot1d Protocol is enabled." ::= { agentPortConfigEntry 4 } agentPortSTPState OBJECT-TYPE SYNTAX INTEGER { discarding(1), learning(2), forwarding(3), disabled(4), manualFwd(5), notParticipate(6) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The switch's Port Spanning Tree Protocol State. This object is only supported when the Dot1d Protocol is enabled." ::= { agentPortConfigEntry 5 } agentPortAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's Port Admin Mode" ::= { agentPortConfigEntry 6 } -- agentPortPhysicalMode OBJECT-TYPE -- SYNTAX INTEGER { -- auto-negotiate(1), -- half-10(2), -- full-10(3), -- half-100(4), -- full-100(5), -- half-100fx(6), -- full-100fx(7), -- full-1000sx(8), -- full-10gsx(9), -- full-40gsx(10) -- } -- MAX-ACCESS read-write -- STATUS obsolete -- DESCRIPTION -- "The switch's Port Speed Mode. This is the configured physical mode. -- This object is read-only for gigabit ports" -- ::= { agentPortConfigEntry 7 } -- agentPortPhysicalStatus OBJECT-TYPE -- SYNTAX INTEGER { -- auto-negotiate(1), -- half-10(2), -- full-10(3), -- half-100(4), -- full-100(5), -- half-100fx(6), -- full-100fx(7), -- full-1000sx(8), -- full-10gsx(9) -- } -- MAX-ACCESS read-only -- STATUS obsolete -- DESCRIPTION -- "The switch's Port Physical Speed Status. This is the current actual speed." -- ::= { agentPortConfigEntry 8 } agentPortLinkTrapMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "If enabled, link up and link down traps will be sent for this port." ::= { agentPortConfigEntry 9 } agentPortClearStats OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "clear stats for this port only" ::= { agentPortConfigEntry 10 } agentPortDefaultType OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-write STATUS current DESCRIPTION "This object identifies the default administrative port type, to be used in conjunction with the operational port type denoted by agentPortType. The set of possible values for this object is the same as the set defined for the agentPortType object. This object represents the administratively-configured type of the MAU. If auto-negotiation is not enabled or is not implemented for this MAU, the value of this object determines the operational type of the MAU. In this case, a set to this object will force the MAU into the specified operating mode. If auto-negotiation is implemented and enabled for this MAU, the operational type of the MAU is determined by auto-negotiation, and the value of this object denotes the type to which the MAU will automatically revert if/when auto-negotiation is later disabled. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD dot3MauType10GBaseLW dot3MauType1000BaseXFD dot3MauType10GigBaseX" REFERENCE "RFC 2668" ::= { agentPortConfigEntry 11 } agentPortType OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the port type. An initial set of MAU types are defined in RFC 2668. The assignment of OBJECT IDENTIFIERs to new types of MAUs is managed by the IANA. If the MAU type is unknown, the object identifier unknownMauType OBJECT IDENTIFIER ::= { 0 0 } is returned. Note that unknownMauType is a syntactically valid object identifier, and any conformant implementation of ASN.1 and the BER must be able to generate and recognize this value. This object represents the operational type of the MAU, as determined by either (1) the result of the auto-negotiation function or (2) if auto-negotiation is not enabled or is not implemented for this MAU, by the value of the object agentPortDefaultType, or (3) for the GigE card a value determined by the GBIC connected to the card. In case (2), a set to the object agentPortDefaultType will force the MAU into the new operating mode. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD dot3MauType1000BaseTFD dot3MauType10GBaseLW dot3MauType1000BaseXFD dot3MauType10GigBaseX" REFERENCE "RFC 2668" ::= { agentPortConfigEntry 12 } agentPortAutoNegAdminStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object identifies the administration status of auto negotiation for this port. Note: Fiber port is read-only" ::= { agentPortConfigEntry 13 } -- agentPortDot3FlowControlMode OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Config flowcontrol allows you to enable or disable -- 802.3x flow control for this port. This value -- applies to only full-duplex mode ports. " -- ::= { agentPortConfigEntry 14 } -- agentPortDVlanTagMode OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Controls the Double Vlan Tag mode on this port." -- ::= { agentPortConfigEntry 15 } -- -- agentPortDVlanTagEthertype OBJECT-TYPE -- SYNTAX Integer32 (1..65535) - 0x0001..0xFFFF -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Configures the Double Vlan Tag Ethertype for this port. -- If this object is supported, ethertype cannot be configured -- globally for the switch. -- -- Commonly used are the Ethertypes for vman tags (34984, or 0x88A8) -- and dot1q tags (33024, or 0x8100)." -- ::= { agentPortConfigEntry 16 } -- -- agentPortDVlanTagCustomerId OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Configures the Customer ID for the Double Vlan Tag for this port." -- ::= { agentPortConfigEntry 17 } agentPortMaxFrameSizeLimit OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the largest value that can be configured for agentPortMaxFrameSize" ::= { agentPortConfigEntry 18 } agentPortMaxFrameSize OBJECT-TYPE SYNTAX Integer32 (1518..12288) MAX-ACCESS read-write STATUS current DESCRIPTION "This object identifies the currently configured maximum frame size value for this port. The maximmum value that this object can be set to is the value of agentPortMaxFrameSizeLimit. For Ethernet ports which support 802.1Q vlan tagging, the minimum value that this object can be set to is 1518" ::= { agentPortConfigEntry 19 } -- agentPortBroadcastControlMode OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "If enabled, broadcast storm recovery will function on this port. -- When you specify Enable for Broadcast Storm Recovery and the broadcast -- traffic on this Ethernet port exceeds the configured threshold, the -- switch blocks (discards) the broadcast traffic." -- ::= { agentPortConfigEntry 20 } -- -- agentPortBroadcastControlThreshold OBJECT-TYPE -- SYNTAX Integer32 (0..14880000) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Configures the broadcast storm recovery threshold for this port -- as a percentage of port speed or as an absolute pps rate." -- ::= { agentPortConfigEntry 21 } -- -- agentPortMulticastControlMode OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "If enabled, multicast storm recovery will function on this port. -- When you specify Enable for Multicast Storm Recovery and the multicast -- traffic on this Ethernet port exceeds the configured threshold, the -- switch blocks (discards) the multicast traffic." -- ::= { agentPortConfigEntry 22 } -- -- agentPortMulticastControlThreshold OBJECT-TYPE -- SYNTAX Integer32 (0..14880000) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Configures the multicast storm recovery threshold for this port -- as a percentage of port speed or as an absolute pps rate." -- ::= { agentPortConfigEntry 23 } -- -- agentPortUnicastControlMode OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "If enabled, unicast storm recovery will function on this port. -- When you specify Enable for Unicast Storm Recovery and the unknown unicast -- traffic on this Ethernet port exceeds the configured threshold, the -- switch blocks (discards) the unknown unicast traffic." -- ::= { agentPortConfigEntry 24 } -- -- agentPortUnicastControlThreshold OBJECT-TYPE -- SYNTAX Integer32 (0..14880000) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Configures the unicast storm recovery threshold for this port -- as a percentage of port speed or as an absolute pps rate." -- ::= { agentPortConfigEntry 25 } agentPortCapability OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "port capability which means(2^bit) are: don't care(0), 10half(2), 10full(4), 100half(8), 100full(16), 1000half(32), 1000full(64), 10Gfull(128), sfp(256), internal(4096), 40Gfull(524288), reserved(1024-2147483648). To enable 10full and 100full, for example, users could set the value to 4(10full)+ 16(100full)= 20. Note: Fiber port is read-only" ::= { agentPortConfigEntry 26 } agentPortBroadcastControlThresholdUnit OBJECT-TYPE SYNTAX INTEGER { percent(1), pps(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configures the units of the threshold value to percentage of port speed or absolute packets per second." DEFVAL { percent } ::= { agentPortConfigEntry 27 } agentPortMulticastControlThresholdUnit OBJECT-TYPE SYNTAX INTEGER { percent(1), pps(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configures the units of the threshold value to percentage of port speed or absolute packets per second." DEFVAL { percent } ::= { agentPortConfigEntry 28 } agentPortUnicastControlThresholdUnit OBJECT-TYPE SYNTAX INTEGER { percent(1), pps(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configures the units of the threshold value to percentage of port speed or absolute packets per second." DEFVAL { percent } ::= { agentPortConfigEntry 29 } agentPortVoiceVlanMode OBJECT-TYPE SYNTAX INTEGER { none(1), vlanid(2), dot1p(3), untagged(4), disable(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Describes and Configures the Port Voice VLAN Mode. This object can only be set to disable(5)." ::= { agentPortConfigEntry 30 } agentPortVoiceVlanID OBJECT-TYPE SYNTAX Integer32 (1..4093) MAX-ACCESS read-write STATUS current DESCRIPTION "Describes and Configures the Port Voice VLAN ID if the Voice Vlan Mode is Vlan ID." ::= { agentPortConfigEntry 31 } agentPortVoiceVlanPriority OBJECT-TYPE SYNTAX INTEGER (0..7|255) MAX-ACCESS read-write STATUS current DESCRIPTION "Describes and Configures the Port Voice VLAN Priority if the Voice Vlan Mode is dot1p. A value of 255 indicates that the priority is not configured." ::= { agentPortConfigEntry 32 } agentPortVoiceVlanDataPriorityMode OBJECT-TYPE SYNTAX INTEGER { trust(1), untrust(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Describes and Configures the Port Voice VLAN Data Priority Mode." ::= { agentPortConfigEntry 33 } agentPortVoiceVlanOperationalStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Describes the Port Voice VLAN Operational Status." ::= { agentPortConfigEntry 34 } agentPortVoiceVlanUntagged OBJECT-TYPE SYNTAX INTEGER{ false(0), true(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Describes and Configures the Port Voice VLAN tagging mode." ::= { agentPortConfigEntry 35 } agentPortVoiceVlanNoneMode OBJECT-TYPE SYNTAX INTEGER{ false(0), true(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Describes and Configures the Port Voice VLAN None mode." ::= { agentPortConfigEntry 36 } agentPortVoiceVlanAuthMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Describes and Configures the Port Voice VLAN Authentication mode. Disable means authentication not required for voice devices when dot1x is enabled." ::= { agentPortConfigEntry 38 } agentPortDot3FlowControlOperStatus OBJECT-TYPE SYNTAX INTEGER { active(1), inactive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies operational status of the flow control per port." ::= { agentPortConfigEntry 39 } agentPortLoadStatsInterval OBJECT-TYPE SYNTAX Integer32 (30..600) MAX-ACCESS read-write STATUS current DESCRIPTION "The length of time for which data is used to compute load statistics. The value is given in seconds, and must be a multiple of 30. The allowable range is 30 to 600 seconds." DEFVAL { 300 } ::= { agentPortConfigEntry 40 } --************************************************************************************** -- agentProtocolConfigGroup --************************************************************************************** agentProtocolConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 14 } agentProtocolGroupCreate OBJECT-TYPE SYNTAX DisplayString (SIZE(0|1..16)) MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Set to non-empty string to create a Protocol-Based VLAN group." ::= { agentProtocolConfigGroup 1 } --************************************************************************************** -- agentProtocolGroupTable --************************************************************************************** agentProtocolGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentProtocolGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the switch's Protocol-based VLAN entries" ::= { agentProtocolConfigGroup 2 } agentProtocolGroupEntry OBJECT-TYPE SYNTAX AgentProtocolGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's Protocol-based VLAN entry" INDEX { agentProtocolGroupId } ::= { agentProtocolGroupTable 1 } AgentProtocolGroupEntry ::= SEQUENCE { agentProtocolGroupId Integer32, agentProtocolGroupName DisplayString, agentProtocolGroupVlanId Integer32, agentProtocolGroupProtocolIP INTEGER, agentProtocolGroupProtocolARP INTEGER, agentProtocolGroupProtocolIPX INTEGER, agentProtocolGroupStatus RowStatus } agentProtocolGroupId OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Group identifier of the Protocol-based VLAN entry." ::= { agentProtocolGroupEntry 1 } agentProtocolGroupName OBJECT-TYPE SYNTAX DisplayString (SIZE(0|1..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "Group name of the Protocol-based VLAN entry." ::= { agentProtocolGroupEntry 2 } agentProtocolGroupVlanId OBJECT-TYPE SYNTAX Integer32 (0..4093) MAX-ACCESS read-write STATUS current DESCRIPTION "VLAN associated with the Protocol-based VLAN entry. Set to 0 to remove." ::= { agentProtocolGroupEntry 3 } agentProtocolGroupProtocolIP OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The status of the IP protocol association with the Protocol-based VLAN entry." ::= { agentProtocolGroupEntry 4 } agentProtocolGroupProtocolARP OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The status of the ARP protocol association with the Protocol-based VLAN entry." ::= { agentProtocolGroupEntry 5 } agentProtocolGroupProtocolIPX OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The status of the IPX protocol association with the Protocol-based VLAN entry." ::= { agentProtocolGroupEntry 6 } agentProtocolGroupStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of the Protocol-based VLAN entry. active(1) - this entry is active createAndGo(4) - used to create a new entry destroy(6) - remove this entry" ::= { agentProtocolGroupEntry 7 } --************************************************************************************** -- agentProtocolGroupPortTable --************************************************************************************** agentProtocolGroupPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentProtocolGroupPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the switch's physical port config entries" ::= { agentProtocolConfigGroup 3 } agentProtocolGroupPortEntry OBJECT-TYPE SYNTAX AgentProtocolGroupPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's physical port config entry" INDEX { agentProtocolGroupId, agentProtocolGroupPortIfIndex } ::= { agentProtocolGroupPortTable 1 } AgentProtocolGroupPortEntry ::= SEQUENCE { agentProtocolGroupPortIfIndex Integer32, agentProtocolGroupPortStatus RowStatus } agentProtocolGroupPortIfIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The interface number of this instance." ::= { agentProtocolGroupPortEntry 1 } agentProtocolGroupPortStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this entry. active(1) - the port is associated with this group createAndGo(4) - add the port to this group createAndWait(5) - add the port to this group destroy(6) - remove the port from this group" ::= { agentProtocolGroupPortEntry 2 } --************************************************************************************** -- agentProtocolGroupProtocolTable --************************************************************************************** agentProtocolGroupProtocolTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentProtocolGroupProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the switch's physical port config entries" ::= { agentProtocolConfigGroup 4 } agentProtocolGroupProtocolEntry OBJECT-TYPE SYNTAX AgentProtocolGroupProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's physical port config entry" INDEX { agentProtocolGroupId, agentProtocolGroupProtocolID } ::= { agentProtocolGroupProtocolTable 1 } AgentProtocolGroupProtocolEntry ::= SEQUENCE { agentProtocolGroupProtocolID Integer32, agentProtocolGroupProtocolStatus RowStatus } agentProtocolGroupProtocolID OBJECT-TYPE SYNTAX Integer32 (1536..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The protocol ID of this instance. The value for IP is 2048 (0x0800), ARP is 2054 (0x0806) and IPX is 33079 (0x8137). Other protocol Ids in the range 1536 to 65535 can also be configured." ::= { agentProtocolGroupProtocolEntry 1 } agentProtocolGroupProtocolStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this entry. active(1) - the port is associated with this group createAndGo(4) - add the port to this group createAndWait(5) - add the port to this group destroy(6) - remove the port from this group" ::= { agentProtocolGroupProtocolEntry 2 } --************************************************************************************** -- agentStpSwitchConfigGroup --************************************************************************************** agentStpSwitchConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 15 } agentStpConfigDigestKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE(16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The MST configuration digest key." ::= { agentStpSwitchConfigGroup 1 } agentStpConfigFormatSelector OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The MST configuration format selector. A value other than 0 (zero) indicates non-support for the IEEE 802.1s standard." ::= { agentStpSwitchConfigGroup 2 } agentStpConfigName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The MST configuration name of at most 32 characters." ::= { agentStpSwitchConfigGroup 3 } agentStpConfigRevision OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The MST configuration revision. The default value is 0." DEFVAL { 0 } ::= { agentStpSwitchConfigGroup 4 } agentStpForceVersion OBJECT-TYPE SYNTAX INTEGER { dot1d(1), dot1w(2), dot1s(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The MST configuration force protocol version. The default version is dot1s." ::= { agentStpSwitchConfigGroup 5 } agentStpAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The spanning tree operational status. enable(1) - enables spanning tree operational status on the switch. disable(2) - disables spanning tree operational status on the switch. The default status is disabled." ::= { agentStpSwitchConfigGroup 6 } --************************************************************************************** -- agentStpPortTable -- --************************************************************************************** agentStpPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentStpPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "STP port table." ::= { agentStpSwitchConfigGroup 7 } agentStpPortEntry OBJECT-TYPE SYNTAX AgentStpPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "STP port entry." INDEX { ifIndex } ::= { agentStpPortTable 1 } AgentStpPortEntry ::= SEQUENCE { agentStpPortState INTEGER, agentStpPortStatsMstpBpduRx Counter32, agentStpPortStatsMstpBpduTx Counter32, agentStpPortStatsRstpBpduRx Counter32, agentStpPortStatsRstpBpduTx Counter32, agentStpPortStatsStpBpduRx Counter32, agentStpPortStatsStpBpduTx Counter32, agentStpPortUpTime TimeTicks, agentStpPortMigrationCheck INTEGER, agentStpPortHelloTime Unsigned32, agentStpPortBPDUGuard INTEGER } agentStpPortState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative STP state for the port. enable(1) - enables STP on the port. disable(2) - disables STP on the port. The default port STP state is enabled for the first 4095 ports and disabled for any ports beyond." ::= { agentStpPortEntry 1 } agentStpPortStatsMstpBpduRx OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP BPDUs received on a specific port." ::= { agentStpPortEntry 2 } agentStpPortStatsMstpBpduTx OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP BPDUs sent from a specific port." ::= { agentStpPortEntry 3 } agentStpPortStatsRstpBpduRx OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The RSTP BPDUs received on a specific port." ::= { agentStpPortEntry 4 } agentStpPortStatsRstpBpduTx OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The RSTP BPDUs sent from a specific port." ::= { agentStpPortEntry 5 } agentStpPortStatsStpBpduRx OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The STP BPDUs received on a specific port." ::= { agentStpPortEntry 6 } agentStpPortStatsStpBpduTx OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The STP BPDUs sent from a specific port." ::= { agentStpPortEntry 7 } agentStpPortUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Time since port was reset. It is displayed in days, hours, minutes, and seconds." ::= { agentStpPortEntry 8 } agentStpPortMigrationCheck OBJECT-TYPE SYNTAX INTEGER { false(0), true(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Force the specified port to transmit RSTP or MSTP BPDU's. Supported values: false(0) - BPDUs are not to be transmitted. true(1) - BPDUs are to be transmitted A non-zero value indicates that BPDUs are to be sent on the specified port." ::= { agentStpPortEntry 9 } agentStpPortHelloTime OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "Hello time for the STP port. The default value is 2." DEFVAL { 2 } ::= { agentStpPortEntry 10 } agentStpPortBPDUGuard OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Don't accept BPDUs on this interface" ::= { agentStpPortEntry 11 } --************************************************************************************** -- agentStpCstConfigGroup -- --************************************************************************************** agentStpCstConfigGroup OBJECT IDENTIFIER ::= { agentStpSwitchConfigGroup 8 } agentStpCstHelloTime OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP root port hello time for the CIST." ::= { agentStpCstConfigGroup 1 } agentStpCstMaxAge OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP root port max age for the CIST." ::= { agentStpCstConfigGroup 2 } agentStpCstRegionalRootId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP regional root identifier for the CIST." ::= { agentStpCstConfigGroup 3 } agentStpCstRegionalRootPathCost OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP regional root path cost for the CIST." ::= { agentStpCstConfigGroup 4 } agentStpCstRootFwdDelay OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP root port forward delay for the CIST." ::= { agentStpCstConfigGroup 5 } agentStpCstBridgeFwdDelay OBJECT-TYPE SYNTAX Unsigned32 (4..30) MAX-ACCESS read-write STATUS current DESCRIPTION "The MSTP bridge forward delay for the CIST. The default value is 15." DEFVAL { 15 } ::= { agentStpCstConfigGroup 6 } agentStpCstBridgeHelloTime OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP bridge hello time for the CIST. The default value is 2. According to IEEE 802.1Q-REV 2005 updating hello time is disallowed" DEFVAL { 2 } ::= { agentStpCstConfigGroup 7 } agentStpCstBridgeHoldTime OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP bridge hold time for the CIST." ::= { agentStpCstConfigGroup 8 } agentStpCstBridgeMaxAge OBJECT-TYPE SYNTAX Unsigned32 (6..40) MAX-ACCESS read-write STATUS current DESCRIPTION "The MSTP bridge max age for the CIST. The default value is 20." DEFVAL { 20 } ::= { agentStpCstConfigGroup 9 } agentStpCstBridgeMaxHops OBJECT-TYPE SYNTAX Unsigned32 (6..40) MAX-ACCESS read-write STATUS current DESCRIPTION "The MSTP bridge max hops for the CIST. The default value is 20." DEFVAL { 20 } ::= { agentStpCstConfigGroup 10 } agentStpCstBridgePriority OBJECT-TYPE SYNTAX Unsigned32 (0..61440) MAX-ACCESS read-write STATUS current DESCRIPTION "The MSTP bridge priority for the CIST. The default value is 32768." DEFVAL { 32768 } ::= { agentStpCstConfigGroup 11 } agentStpCstBridgeHoldCount OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The MSTP bridge hold count for the CIST. This command sets the value of maximum bpdus that a bridge is allowed to send within a hello time window. The default value is 6." DEFVAL { 6 } ::= { agentStpCstConfigGroup 12 } --************************************************************************************** -- agentStpCstPortTable -- --************************************************************************************** agentStpCstPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentStpCstPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "CIST port table." ::= { agentStpSwitchConfigGroup 9 } agentStpCstPortEntry OBJECT-TYPE SYNTAX AgentStpCstPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "CIST port entry." INDEX { ifIndex } ::= { agentStpCstPortTable 1 } AgentStpCstPortEntry ::= SEQUENCE { agentStpCstPortOperEdge INTEGER, agentStpCstPortOperPointToPoint INTEGER, agentStpCstPortTopologyChangeAck INTEGER, agentStpCstPortEdge INTEGER, agentStpCstPortForwardingState INTEGER, agentStpCstPortId OCTET STRING, agentStpCstPortPathCost Unsigned32, agentStpCstPortPriority Unsigned32, agentStpCstDesignatedBridgeId OCTET STRING, agentStpCstDesignatedCost Unsigned32, agentStpCstDesignatedPortId OCTET STRING, agentStpCstExtPortPathCost Unsigned32, agentStpCstPortBpduGuardEffect INTEGER, agentStpCstPortBpduFilter INTEGER, agentStpCstPortBpduFlood INTEGER, agentStpCstPortAutoEdge INTEGER, agentStpCstPortRootGuard INTEGER, agentStpCstPortTCNGuard INTEGER, agentStpCstPortLoopGuard INTEGER } agentStpCstPortOperEdge OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP operational status of a specific port for the CIST." ::= { agentStpCstPortEntry 1 } agentStpCstPortOperPointToPoint OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP operational point to point mac of a specific port for the CIST." ::= { agentStpCstPortEntry 2 } agentStpCstPortTopologyChangeAck OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP topology change acknowledge for a specific port in the CIST." ::= { agentStpCstPortEntry 3 } agentStpCstPortEdge OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative state of a specific port in CIST. enable(1) - enables the port. disable(2) - disables the port. The default port state is disabled." ::= { agentStpCstPortEntry 4 } agentStpCstPortForwardingState OBJECT-TYPE SYNTAX INTEGER { discarding(1), learning(2), forwarding(3), disabled(4), manualFwd(5), notParticipate(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP forwarding state of a specific port in CIST." ::= { agentStpCstPortEntry 5 } agentStpCstPortId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(2)) MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP port identifier of a specific port in CIST." ::= { agentStpCstPortEntry 6 } agentStpCstPortPathCost OBJECT-TYPE SYNTAX Unsigned32 (0..200000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The MSTP port path cost in CIST. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed." ::= { agentStpCstPortEntry 7 } agentStpCstPortPriority OBJECT-TYPE SYNTAX Unsigned32 (0..240) MAX-ACCESS read-write STATUS current DESCRIPTION "The MSTP port priority in CIST. The priority is in the increments of 16. The default value is 128." DEFVAL { 128 } ::= { agentStpCstPortEntry 8 } agentStpCstDesignatedBridgeId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP designated bridge ID of a specific port in CIST." ::= { agentStpCstPortEntry 9 } agentStpCstDesignatedCost OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP designated cost of a specific port in CIST." ::= { agentStpCstPortEntry 10 } agentStpCstDesignatedPortId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(2)) MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP designated port ID of a specific port in CIST." ::= { agentStpCstPortEntry 11 } agentStpCstExtPortPathCost OBJECT-TYPE SYNTAX Unsigned32 (0..200000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The MSTP external port path cost in CIST. The default value varies depending upon the link speed." ::= { agentStpCstPortEntry 12 } agentStpCstPortBpduGuardEffect OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "BPDU Guard Mode effect on the port. enable(1) - BPDU Guard Mode is enabled on the port. disable(2) - BPDU Guard Mode is disabled on the port." ::= { agentStpCstPortEntry 13 } agentStpCstPortBpduFilter OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This command sets BPDU Filter mode on the port. enable(1) - BPDU Filter Mode is enabled on the port. disable(2) - BPDU Filter Mode is disabled on the port." ::= { agentStpCstPortEntry 14 } agentStpCstPortBpduFlood OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This command sets BPDU Flood mode on the port. enable(1) - BPDU Flood Mode is enabled on the port. disable(2) - BPDU Flood Mode is disabled on the port." ::= { agentStpCstPortEntry 15 } agentStpCstPortAutoEdge OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This command sets the auto-edge mode of the port which enables it to become an edge port if it does not see BPDUs for some duration. enable(1) - enables the auto-edge mode for the port. disable(2) - disables the auto-edge mode for the port. The default auto-edge mode is enabled." ::= { agentStpCstPortEntry 16 } agentStpCstPortRootGuard OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This command sets a port to discard any superior information received by the port and thus protect against root of the device from changing.The port gets put into discarding state and does not forward any packets. enable(1) - enables the root-guard mode for the port. disable(2) - disables the root-guard mode for the port. The default root-guard mode is disabled." ::= { agentStpCstPortEntry 17 } agentStpCstPortTCNGuard OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This command restricts the port from propagating any topology change information received through that port. enable(1) - enables the tcn-guard mode for the port. disable(2) - disables the tcn-guard mode for the port. The default tcn-guard mode is disabled." ::= { agentStpCstPortEntry 18 } agentStpCstPortLoopGuard OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This command enables loop guard on this port. This setting applies to all Spanning Tree instances of which this port is a member. enable(1) - enables the loop guard mode for the port. disable(2) - disables the loop guard mode for the port. The default loop-guard mode is disabled." ::= { agentStpCstPortEntry 19 } --************************************************************************************** -- agentStpMstTable -- --************************************************************************************** agentStpMstTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentStpMstEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "MST table." ::= { agentStpSwitchConfigGroup 10 } agentStpMstEntry OBJECT-TYPE SYNTAX AgentStpMstEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "MST entry." INDEX { agentStpMstId } ::= { agentStpMstTable 1 } AgentStpMstEntry ::= SEQUENCE { agentStpMstId Unsigned32, agentStpMstBridgePriority Unsigned32, agentStpMstBridgeIdentifier OCTET STRING, agentStpMstDesignatedRootId OCTET STRING, agentStpMstRootPathCost Unsigned32, agentStpMstRootPortId OCTET STRING, agentStpMstTimeSinceTopologyChange TimeTicks, agentStpMstTopologyChangeCount Counter32, agentStpMstTopologyChangeParm INTEGER, agentStpMstRowStatus RowStatus } agentStpMstId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP instance ID." ::= { agentStpMstEntry 1 } agentStpMstBridgePriority OBJECT-TYPE SYNTAX Unsigned32 (0..61440) MAX-ACCESS read-write STATUS current DESCRIPTION "The MSTP bridge priority in a specific instance. The priority is in the increments of 4096. The recommended default value is 32768." ::= { agentStpMstEntry 2 } agentStpMstBridgeIdentifier OBJECT-TYPE SYNTAX OCTET STRING (SIZE(8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP bridge identifier in a specific instance." ::= { agentStpMstEntry 3 } agentStpMstDesignatedRootId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP designated root bridge identifier in a specific instance." ::= { agentStpMstEntry 4 } agentStpMstRootPathCost OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP root path cost in a specific instance." ::= { agentStpMstEntry 5 } agentStpMstRootPortId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP root port ID in a specific instance." ::= { agentStpMstEntry 6 } agentStpMstTimeSinceTopologyChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP time since the last topology change in a specific instance." ::= { agentStpMstEntry 7 } agentStpMstTopologyChangeCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP count of topology changes in a specific instance." ::= { agentStpMstEntry 8 } agentStpMstTopologyChangeParm OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP topology change parameter in a specific instance." ::= { agentStpMstEntry 9 } agentStpMstRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The MSTP instance status. Supported values: active(1) - valid instance. createAndGo(4) - used to create a new instance. destroy(6) - removes an instance." ::= { agentStpMstEntry 10 } --************************************************************************************** -- agentStpMstPortTable -- --************************************************************************************** agentStpMstPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentStpMstPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "MST port table." ::= { agentStpSwitchConfigGroup 11 } agentStpMstPortEntry OBJECT-TYPE SYNTAX AgentStpMstPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "MST port entry." INDEX { agentStpMstId, ifIndex } ::= { agentStpMstPortTable 1 } AgentStpMstPortEntry ::= SEQUENCE { agentStpMstPortForwardingState INTEGER, agentStpMstPortId OCTET STRING, agentStpMstPortPathCost Unsigned32, agentStpMstPortPriority Unsigned32, agentStpMstDesignatedBridgeId OCTET STRING, agentStpMstDesignatedCost Unsigned32, agentStpMstDesignatedPortId OCTET STRING, agentStpMstPortLoopInconsistentState INTEGER, agentStpMstPortTransitionsIntoLoopInconsistentState Counter32, agentStpMstPortTransitionsOutOfLoopInconsistentState Counter32 } agentStpMstPortForwardingState OBJECT-TYPE SYNTAX INTEGER { discarding(1), learning(2), forwarding(3), disabled(4), manualFwd(5), notParticipate(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP forwarding state of a specific port in a specific instance." ::= { agentStpMstPortEntry 1 } agentStpMstPortId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(4)) MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP port identifier of a specific port in a specific instance." ::= { agentStpMstPortEntry 2 } agentStpMstPortPathCost OBJECT-TYPE SYNTAX Unsigned32 (0..200000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The MSTP port path cost in a specific instance. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed." ::= { agentStpMstPortEntry 3 } agentStpMstPortPriority OBJECT-TYPE SYNTAX Unsigned32 (0..240) MAX-ACCESS read-write STATUS current DESCRIPTION "The MSTP port priority in a specific instance. The priority is in the increments of 16. The default value is 128." DEFVAL { 128 } ::= { agentStpMstPortEntry 4 } agentStpMstDesignatedBridgeId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP designated bridge ID of a specific port in a specific instance." ::= { agentStpMstPortEntry 5 } agentStpMstDesignatedCost OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP designated cost of a specific port in a specific instance." ::= { agentStpMstPortEntry 6 } agentStpMstDesignatedPortId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(2)) MAX-ACCESS read-only STATUS current DESCRIPTION "The MSTP designated port ID of a specific port in a specific instance." ::= { agentStpMstPortEntry 7 } agentStpMstPortLoopInconsistentState OBJECT-TYPE SYNTAX INTEGER { false(0), true(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "The loop inconsistent state of a specific port in a specific instance. This value can only report as true(1) when loop guard is enabled on the port and the port has transitioned from blocking state in this MST instance." ::= { agentStpMstPortEntry 8 } agentStpMstPortTransitionsIntoLoopInconsistentState OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this interface has transitioned into loop inconsistent state." ::= { agentStpMstPortEntry 9 } agentStpMstPortTransitionsOutOfLoopInconsistentState OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this interface has transitioned out of loop inconsistent state." ::= { agentStpMstPortEntry 10 } --************************************************************************************** -- agentStpMstVlanTable -- --************************************************************************************** agentStpMstVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentStpMstVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "MST VLAN table." ::= { agentStpSwitchConfigGroup 12 } agentStpMstVlanEntry OBJECT-TYPE SYNTAX AgentStpMstVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "MST VLAN entry." INDEX { agentStpMstId, dot1qVlanIndex } ::= { agentStpMstVlanTable 1 } AgentStpMstVlanEntry ::= SEQUENCE { agentStpMstVlanRowStatus RowStatus } agentStpMstVlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The association status of an MSTP instance and a VLAN. Supported values: active(1) - valid association between an MSTP instance and a VLAN. createAndGo(4) - used to create a new association between an MSTP instance and a VLAN. destroy(6) - removes the association between an MSTP instance and a VLAN." ::= { agentStpMstVlanEntry 1 } agentStpBpduGuardMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The spanning tree BPDU Guard Mode. enable(1) - enables BPDU Guard Mode on the switch. disable(2) - disables BPDU Guard Mode on the switch. The default status is disabled." ::= { agentStpSwitchConfigGroup 13 } agentStpBpduFilterDefault OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The spanning tree BPDU Filter Mode, it enables BPDU Filter on all edge ports. enable(1) - enables BPDU Filter Mode on the switch. disable(2) - disables BPDU Filter Mode on the switch. The default status is disabled." ::= { agentStpSwitchConfigGroup 14 } agentStpUplinkFast OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable UplinkFast Feature." ::= { agentStpSwitchConfigGroup 15 } --************************************************************************************** -- agentAuthenticationGroup --************************************************************************************** agentAuthenticationGroup OBJECT IDENTIFIER ::= { agentConfigGroup 16 } agentAuthenticationListCreate OBJECT-TYPE SYNTAX DisplayString (SIZE(0|1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "Authentication List Create If set to a non empty string, creates a new Authentication Login List for configuration." ::= { agentAuthenticationGroup 1 } agentAuthenticationEnableListCreate OBJECT-TYPE SYNTAX DisplayString (SIZE(0|1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "Authentication Enable List Create If set to a non empty string, creates a new Authentication Enable List for configuration." ::= { agentAuthenticationGroup 7 } --************************************************************************************** agentAuthenticationListTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentAuthenticationListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "MST VLAN table." ::= { agentAuthenticationGroup 2 } agentAuthenticationListEntry OBJECT-TYPE SYNTAX AgentAuthenticationListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "MST VLAN entry." INDEX { agentAuthenticationListIndex } ::= { agentAuthenticationListTable 1 } AgentAuthenticationListEntry ::= SEQUENCE { agentAuthenticationListIndex Unsigned32, agentAuthenticationListName DisplayString, agentAuthenticationListMethod1 INTEGER, agentAuthenticationListMethod2 INTEGER, agentAuthenticationListMethod3 INTEGER, agentAuthenticationListStatus RowStatus, agentAuthenticationListMethod4 INTEGER, agentAuthenticationListMethod5 INTEGER, agentAuthenticationListMethod6 INTEGER, agentAuthenticationListAccessType INTEGER, agentAuthenticationListAccessLevel INTEGER } agentAuthenticationListIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Authenticaiton List Index Unique number used for indexing into this table." ::= { agentAuthenticationListEntry 1 } agentAuthenticationListName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "Authenticaiton List Name Unique name used to identify the Authentication List from other tables." ::= { agentAuthenticationListEntry 2 } agentAuthenticationListMethod1 OBJECT-TYPE SYNTAX INTEGER { undefined(0), enable(1), line(2), local(3), none(4), radius(5), tacacs(6), ias(7), reject(8), ldap(9) } MAX-ACCESS read-write STATUS current DESCRIPTION "Authenticion List Method 1 Configures the first authentication method to use when this list is specified." ::= { agentAuthenticationListEntry 3 } agentAuthenticationListMethod2 OBJECT-TYPE SYNTAX INTEGER { undefined(0), enable(1), line(2), local(3), none(4), radius(5), tacacs(6), ias(7), reject(8), ldap(9) } MAX-ACCESS read-write STATUS current DESCRIPTION "Authenticion List Method 2 Configures the second authentication method to use when this list is specified." ::= { agentAuthenticationListEntry 4 } agentAuthenticationListMethod3 OBJECT-TYPE SYNTAX INTEGER { undefined(0), enable(1), line(2), local(3), none(4), radius(5), tacacs(6), ias(7), reject(8), ldap(9) } MAX-ACCESS read-write STATUS current DESCRIPTION "Authenticion List Method 3 Configures the third authentication method to use when this list is specified." ::= { agentAuthenticationListEntry 5 } agentAuthenticationListStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of the Authentication List. Supported values: active(1) - indicates a valid Authenticaiton List destroy(6) - removes the Authentication List." ::= { agentAuthenticationListEntry 6 } agentAuthenticationListMethod4 OBJECT-TYPE SYNTAX INTEGER { undefined(0), enable(1), line(2), local(3), none(4), radius(5), tacacs(6), ias(7), reject(8), ldap(9) } MAX-ACCESS read-write STATUS current DESCRIPTION "Authenticion List Method 4 Configures the fourth authentication method to use when this list is specified." ::= { agentAuthenticationListEntry 7 } agentAuthenticationListMethod5 OBJECT-TYPE SYNTAX INTEGER { undefined(0), enable(1), line(2), local(3), none(4), radius(5), tacacs(6), ias(7), reject(8), ldap(9) } MAX-ACCESS read-write STATUS current DESCRIPTION "Authenticion List Method 5 Configures the fifth authentication method to use when this list is specified." ::= { agentAuthenticationListEntry 8 } agentAuthenticationListMethod6 OBJECT-TYPE SYNTAX INTEGER { undefined(0), enable(1), line(2), local(3), none(4), radius(5), tacacs(6), ias(7), reject(8), ldap(9) } MAX-ACCESS read-write STATUS current DESCRIPTION "Authenticion List Method 6 Configures the sixth authentication method to use when this list is specified." ::= { agentAuthenticationListEntry 9 } agentAuthenticationListAccessType OBJECT-TYPE SYNTAX INTEGER { unknown(0), console(1), telnet(2), ssh(3), https(4), http(5), dot1x(6), cts(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Authenticion List Access Type Shows the authentication list access type. cts is the authentication list type for console, telnet, and ssh." ::= { agentAuthenticationListEntry 10 } agentAuthenticationListAccessLevel OBJECT-TYPE SYNTAX INTEGER { unknown(0), login(1), enable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Authenticion List Access Level Shows the authentication list access level." ::= { agentAuthenticationListEntry 11 } --************************************************************************************** agentUserConfigDefaultAuthenticationList OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "Default Authentication List This object configures which authentication list to use for users which do not have an Authentication List configured. The list must be configured before setting." ::= { agentAuthenticationGroup 3 } agentUserConfigDefaultAuthenticationDot1xList OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "Default Authentication List 802.1x This object configures which authentication list to use for users which do not have an Authentication List configured. The list must be configured before setting." ::= { agentAuthenticationGroup 6 } --************************************************************************************** agentUserAuthenticationConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentUserAuthenticationConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "User Authentication Config Table" ::= { agentAuthenticationGroup 4 } agentUserAuthenticationConfigEntry OBJECT-TYPE SYNTAX AgentUserAuthenticationConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "User Authentication Config Entry" AUGMENTS { agentUserConfigEntry } ::= { agentUserAuthenticationConfigTable 1 } AgentUserAuthenticationConfigEntry ::= SEQUENCE { agentUserAuthenticationList DisplayString, agentUserAuthenticationDot1xList DisplayString } agentUserAuthenticationList OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "User Authentication List This object configures which authentication list to use for this user. The list must be configured before setting." ::= { agentUserAuthenticationConfigEntry 1 } agentUserAuthenticationDot1xList OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "User Authentication List 802.1x This object configures which authentication list to use for this user. The list must be configured before setting." ::= { agentUserAuthenticationConfigEntry 2 } --************************************************************************************** agentUserPortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentUserPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "User Port Config Table" ::= { agentAuthenticationGroup 5 } agentUserPortConfigEntry OBJECT-TYPE SYNTAX AgentUserPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "User Port Config Entry" AUGMENTS { agentUserConfigEntry } ::= { agentUserPortConfigTable 1 } AgentUserPortConfigEntry ::= SEQUENCE { agentUserPortSecurity AgentPortMask } agentUserPortSecurity OBJECT-TYPE SYNTAX AgentPortMask MAX-ACCESS read-write STATUS current DESCRIPTION "User Port Port Security This object configures which ports the user has access to. Ports are indexed based on dot1dBasePort entries in dot1dBasePortTable." ::= { agentUserPortConfigEntry 1 } --************************************************************************************** -- agentClassOfServiceGroup --************************************************************************************** agentClassOfServiceGroup OBJECT IDENTIFIER ::= { agentConfigGroup 17 } agentClassOfServicePortTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentClassOfServicePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about the 802.1p priority mapping to traffic class priority queue for every physical port." ::= { agentClassOfServiceGroup 1 } agentClassOfServicePortEntry OBJECT-TYPE SYNTAX AgentClassOfServicePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A 802.1p priority mapped to a traffic class priority queue." INDEX { ifIndex, agentClassOfServicePortPriority } ::= { agentClassOfServicePortTable 1 } AgentClassOfServicePortEntry ::= SEQUENCE { agentClassOfServicePortPriority INTEGER, agentClassOfServicePortClass INTEGER } agentClassOfServicePortPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Priority value determined for the received frame. This value is equivalent to the priority indicated in the tagged frame received, or one of the evaluated priorities, determined according to the media-type. For untagged frames received from Ethernet media, this value is equal to the dot1dPortDefaultUserPriority value for the ingress port." ::= { agentClassOfServicePortEntry 1 } agentClassOfServicePortClass OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Traffic class priority queue the received frame is mapped to." ::= { agentClassOfServicePortEntry 2 } --************************************************************************************** -- agentHTTPConfigGroup -- --************************************************************************************** agentHTTPConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 19 } -- agentHTTPWebMode OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Configures the HTTP server admin mode" -- ::= { agentHTTPConfigGroup 1 } -- -- agentHTTPJavaMode OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Configures the use of the Java interface through Web connections." -- ::= { agentHTTPConfigGroup 2 } agentHTTPMaxSessions OBJECT-TYPE SYNTAX Integer32 (0..16) MAX-ACCESS read-write STATUS current DESCRIPTION "Configures the maximum number of allowable HTTP sessions. The default value is 16." ::= { agentHTTPConfigGroup 3 } agentHTTPHardTimeout OBJECT-TYPE SYNTAX Integer32 (0..168) MAX-ACCESS read-write STATUS current DESCRIPTION "Configures the hard timeout for HTTP sessions in hours. The default value is 24 hours. A value of zero means http will not timeout." ::= { agentHTTPConfigGroup 4 } agentHTTPSoftTimeout OBJECT-TYPE SYNTAX Integer32 (0..60) MAX-ACCESS read-write STATUS current DESCRIPTION "Configures the soft (activity) timeout for HTTP sessions in minutes. The default value is 5 minutes. A value of zero means http will not timeout." ::= { agentHTTPConfigGroup 5 } --************************************************************************************** -- agentAutoInstallConfigGroup -- --************************************************************************************** agentAutoInstallConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 20 } agentAutoinstallPersistentMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Autoinstall on device." ::= { agentAutoInstallConfigGroup 1 } agentAutoinstallAutosaveMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Auto Save of downloaded configuration on device." ::= { agentAutoInstallConfigGroup 2 } agentAutoinstallUnicastRetryCount OBJECT-TYPE SYNTAX Integer32 (1..3) MAX-ACCESS read-write STATUS current DESCRIPTION "Sets number of unicast TFTP attempts for configuration file." ::= { agentAutoInstallConfigGroup 3 } agentAutoinstallStatus OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Display current Autoinstall status on device." ::= { agentAutoInstallConfigGroup 4 } agentAutoinstallAutoRebootMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Auto Reboot after succesfull image update on device." ::= { agentAutoInstallConfigGroup 5 } agentAutoinstallOperationalMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Autoinstall operational mode on device." ::= { agentAutoInstallConfigGroup 6 } agentAutoinstallAutoUpgradeMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Autoinstall auto upgrade mode on device." ::= { agentAutoInstallConfigGroup 7 } --************************************************************************************** -- agentLDAPConfigGroup -- --************************************************************************************** agentLDAPConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 25 } agentLDAPServerIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The ldap's server ip" ::= { agentLDAPConfigGroup 1 } agentLDAPServerPort OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The ldap's server port" ::= { agentLDAPConfigGroup 2 } agentLDAPBaseDn OBJECT-TYPE SYNTAX DisplayString (SIZE (0..256)) MAX-ACCESS read-write STATUS current DESCRIPTION "The ldap's base domain" ::= { agentLDAPConfigGroup 3 } agentLDAPRacName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..256)) MAX-ACCESS read-write STATUS current DESCRIPTION "The ldap's rac name" ::= { agentLDAPConfigGroup 4 } agentLDAPRacDomain OBJECT-TYPE SYNTAX DisplayString (SIZE (0..256)) MAX-ACCESS read-write STATUS current DESCRIPTION "The ldap's rac domain" ::= { agentLDAPConfigGroup 5 } --************************************************************************************** -- agentDDnsConfigGroup -- --************************************************************************************** agentDDnsConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 26 } agentDDnsConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDDnsConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the switch's DDNS Config entries" ::= { agentDDnsConfigGroup 1 } agentDDnsConfigEntry OBJECT-TYPE SYNTAX AgentDDnsConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's DDNS Config entry" INDEX { agentDDnsIndex } ::= { agentDDnsConfigTable 1 } AgentDDnsConfigEntry ::= SEQUENCE { agentDDnsIndex Unsigned32, agentDDnsServName INTEGER, agentDDnsUserName DisplayString, agentDDnsPassword DisplayString, agentDDnsHost DisplayString, agentDDnsAddress DisplayString, agentDDnsStatus RowStatus } agentDDnsIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object uniquely identifies the entry in the table." ::= { agentDDnsConfigEntry 1 } agentDDnsServName OBJECT-TYPE SYNTAX INTEGER { easydns(0), dyndns(1), dhs(2), ods(3), dyns(4), zoneedit(5), tzo(6) } MAX-ACCESS read-create STATUS current DESCRIPTION "The DDNS server name of the DDNS service provider." ::= { agentDDnsConfigEntry 2 } agentDDnsUserName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The user name of DDNS account. It can be up to 32 alphanumeric characters." ::= { agentDDnsConfigEntry 3 } agentDDnsPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The password of DDNS account. It can be up to 32 alphanumeric characters." ::= { agentDDnsConfigEntry 4 } agentDDnsHost OBJECT-TYPE SYNTAX DisplayString (SIZE(1..44)) MAX-ACCESS read-create STATUS current DESCRIPTION "The host name of DDNS client. It can be up to 40 alphanumeric characters." ::= { agentDDnsConfigEntry 5 } agentDDnsAddress OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-create STATUS current DESCRIPTION "The switch's network ip address" DEFVAL { "0.0.0.0" } ::= { agentDDnsConfigEntry 6 } agentDDnsStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Agent DDNS Status. active(1) - This DDNS setting is active. createAndGo(4) - used to create a new entry. destroy(6) - Set to this value to remove this DDNS setting." ::= { agentDDnsConfigEntry 7 } --************************************************************************************** -- agentUdldConfigGroup -- --************************************************************************************** agentUdldConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 28 } agentUdldMessageTime OBJECT-TYPE SYNTAX Unsigned32 (7..90) MAX-ACCESS read-write STATUS current DESCRIPTION "UDLD Message Time." ::= { agentUdldConfigGroup 1 } agentUdldConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentUdldConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the switch's SNTP dynamic server entries" ::= { agentUdldConfigGroup 2 } agentUdldConfigEntry OBJECT-TYPE SYNTAX AgentUdldConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's SNTP dynamic server entry" INDEX { agentUdldIndex } ::= { agentUdldConfigTable 1 } AgentUdldConfigEntry ::= SEQUENCE { agentUdldIndex Unsigned32, agentUdldIntfAdminMode INTEGER, agentUdldIntfAggressiveMode INTEGER } agentUdldIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate UDLD interface." ::= { agentUdldConfigEntry 1 } agentUdldIntfAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The interface UDLD admin mode." ::= { agentUdldConfigEntry 2 } agentUdldIntfAggressiveMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The interface UDLD aggressive mode." ::= { agentUdldConfigEntry 3 } --************************************************************************************** -- agentSystemGroup --************************************************************************************** agentSystemGroup OBJECT IDENTIFIER ::= { switching 3 } agentSaveConfig OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "enable(1) will initiate an configuration save to nvram. Status is returned by the object agentSaveConfigStatus." ::= { agentSystemGroup 1 } agentClearConfig OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "clear config to factory defaults" ::= { agentSystemGroup 2 } agentClearLags OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "clear lag configuration" ::= { agentSystemGroup 3 } agentClearLoginSessions OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "close all telnet sessions" ::= { agentSystemGroup 4 } agentClearPasswords OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "reset passwords" ::= { agentSystemGroup 5 } agentClearPortStats OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "clear all port statistics" ::= { agentSystemGroup 6 } agentClearSwitchStats OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "clear all switch statistics" ::= { agentSystemGroup 7 } agentClearBufferedLog OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear Buffered Log" ::= { agentSystemGroup 8 } agentClearTrapLog OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "clear trap log" ::= { agentSystemGroup 9 } agentClearVlan OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "clear vlan entries" ::= { agentSystemGroup 10 } agentResetSystem OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Resets the switch. This object is not valid for stacking platforms." ::= { agentSystemGroup 12 } -- agentSaveConfigStatus OBJECT-TYPE -- SYNTAX INTEGER { -- notInitiated(1), -- savingInProcess(2), -- savingComplete(3), -- savingFailed(4) -- } -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Indicates the current status of an save configuration request." -- ::= { agentSystemGroup 13 } agentConfigCurrentSystemTime OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Current System Time in hh:mm:ss D M Y format, e.g., 13:45:50 25 9 2004. Users have to disable agentSntpClientMode in SNTP-CLIENT-MIB before configuring agentConfigCurrentSystemTime." ::= { agentSystemGroup 14 } agentCpuLoad OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The CPU load." ::= { agentSystemGroup 15 } agentCpuLoadOneMin OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The CPU load average in 1 minute." ::= { agentSystemGroup 16 } agentCpuLoadFiveMin OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The CPU load average in 5 minutes." ::= { agentSystemGroup 17 } agentStartupConfigErase OBJECT-TYPE SYNTAX INTEGER { erase(1) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Erase the text-based configuration file stored in non-volatile memory.On read returns 0." ::= { agentSystemGroup 18 } --************************************************************************************** -- agentCableTesterGroup -- -- This group provides configuration and status of the Virtual Cable Tester -- feature. This provides cable fault and length estimation on copper cables. -- Once initiated, the test requires up to 2 seconds before results are obtained. -- If the link specified to test is active, it will go down for the duration of -- the test. -- --************************************************************************************** --agentCableTesterGroup OBJECT IDENTIFIER ::= { switching 4 } -- -- agentCableTesterStatus OBJECT-TYPE -- SYNTAX INTEGER { -- active(1), -- success(2), -- failure(3), -- uninitialized(4) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Status of the Virtual Cable Tester -- active(1) - cable testing is in progress. Set to this value -- to start the test. -- success(2) - A successful test was performed. Cannot be set. -- failure(3) - A failure was encountered during the test. -- Cannot be set. -- uninitialized(4) - No test has been performed yet. Cannot be set." -- DEFVAL { uninitialized } -- ::= { agentCableTesterGroup 1 } -- -- agentCableTesterIfIndex OBJECT-TYPE -- SYNTAX Unsigned32 -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Determines on which port to perform the cable test. Limited to -- copper based ports." -- DEFVAL { 0 } -- ::= { agentCableTesterGroup 2 } -- -- agentCableTesterCableStatus OBJECT-TYPE -- SYNTAX INTEGER { -- normal(1), -- open(2), -- short(3), -- unknown(4) -- } -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Indicates the results of the Cable Test. -- -- -- normal(1) - The cable is working correctly. -- open(2) - The cable is disconnected or there is a faulty -- connector. -- short(3) - There is an electrical short in the cable. -- unknown(4) - No test has been performed yet, or a test is -- currently in progress." -- DEFVAL { unknown } -- ::= { agentCableTesterGroup 3 } -- -- agentCableTesterMinimumCableLength OBJECT-TYPE -- SYNTAX Unsigned32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The estimated length of the cable in meters. This value -- indicates the shortest length estimated. This object will -- return 0 if agentCableTesterStatus is not success(2) or the cable -- length is unknown." -- DEFVAL { 0 } -- ::= { agentCableTesterGroup 4 } -- -- agentCableTesterMaximumCableLength OBJECT-TYPE -- SYNTAX Unsigned32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The estimated length of the cable in meters. This value -- indicates the longest length estimated. This object will -- return 0 if agentCableTesterStatus is not success(2) or the cable -- length is unknown." -- DEFVAL { 0 } -- ::= { agentCableTesterGroup 5 } -- -- agentCableTesterCableFailureLocation OBJECT-TYPE -- SYNTAX Unsigned32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The estimated distance in meters from the end of the cable to -- the failure location. This object will return 0 if -- agentCableTesterStatus is not success(2)." -- DEFVAL { 0 } -- ::= { agentCableTesterGroup 6 } --************************************************************************************** agentDaiConfigGroup OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 21 } --************************************************************************************** --************ The Dynamic ARP Inspection Global Config Table ******** agentDaiSrcMacValidate OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether Sender MAC validation in the ARP packets is enabled. If this object is set to 'true', validation is enabled. If this object is set to 'false', validation is disabled." DEFVAL { false } ::= { agentDaiConfigGroup 1 } agentDaiDstMacValidate OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether Target MAC validation in the ARP Response packets is enabled. If this object is set to 'true', validation is enabled. If this object is set to 'false', validation is disabled." DEFVAL { false } ::= { agentDaiConfigGroup 2 } agentDaiIPValidate OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether IP address validation in the ARP packets is enabled. If this object is set to 'true', validation is enabled. If this object is set to 'false', validation is disabled." DEFVAL { false } ::= { agentDaiConfigGroup 3 } --************ The Dynamic ARP Inspection VLAN Config Table ******** agentDaiVlanConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDaiVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table provides the mechanism to control Dynamic ARP Inspection per VLAN. When a VLAN is created in a device supporting this table, a corresponding entry of this table will be added." ::= { agentDaiConfigGroup 4 } agentDaiVlanConfigEntry OBJECT-TYPE SYNTAX AgentDaiVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row instance contains the configuration for Dynamic ARP Inspection at each existing VLAN." INDEX { agentDaiVlanIndex } ::= { agentDaiVlanConfigTable 1 } AgentDaiVlanConfigEntry ::= SEQUENCE { agentDaiVlanIndex VlanIndex, agentDaiVlanDynArpInspEnable TruthValue, agentDaiVlanLoggingEnable TruthValue, agentDaiVlanArpAclName DisplayString, agentDaiVlanArpAclStaticFlag TruthValue } agentDaiVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the VLAN number on which Dynamic ARP Inspection feature is configured." ::= { agentDaiVlanConfigEntry 1 } agentDaiVlanDynArpInspEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether Dynamic ARP Inspection is enabled in this VLAN. If this object is set to 'true', Dynamic ARP Inspection is enabled. If this object is set to 'false', Dynamic ARP Inspection is disabled." DEFVAL { false } ::= { agentDaiVlanConfigEntry 2 } agentDaiVlanLoggingEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the Dynamic ARP Inspection logging is enabled on this VlAN. If this object is set to 'true', Dynamic ARP Inspection logging is enabled. If this object is set to 'false', Dynamic ARP Inspection loging is disabled." DEFVAL { true } ::= { agentDaiVlanConfigEntry 3 } agentDaiVlanArpAclName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..31)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the ARP ACL name set for this VLAN." ::= { agentDaiVlanConfigEntry 4 } agentDaiVlanArpAclStaticFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the ARP ACL set for this VLAN has static flag set. If this object is set to 'true', static flag is enabled. If this object is set to 'false', static flag is disabled." DEFVAL { false } ::= { agentDaiVlanConfigEntry 5 } --************ The Dynamic ARP Inspection Vlan Statistics Table ******** agentDaiStatsReset OBJECT-TYPE SYNTAX INTEGER { none(0), reset(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear the DAI statistics on all vlans. A value of reset(1) is used to reset the statistics. A read on this object will always return the value none(0). The value none(0) cannot be forcibly set by the administrator." ::= { agentDaiConfigGroup 5 } agentDaiVlanStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDaiVlanStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table provides the mechanism to control Dynamic ARP Inspection per VLAN. When a VLAN is created in a device supporting this table, a corresponding entry of this table will be added." ::= { agentDaiConfigGroup 6 } agentDaiVlanStatsEntry OBJECT-TYPE SYNTAX AgentDaiVlanStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row instance contains the Dynamic ARP Inspection statistics per VLAN." INDEX { agentDaiVlanStatsIndex } ::= { agentDaiVlanStatsTable 1 } AgentDaiVlanStatsEntry ::= SEQUENCE { agentDaiVlanStatsIndex VlanIndex, agentDaiVlanPktsForwarded Counter32, agentDaiVlanPktsDropped Counter32, agentDaiVlanDhcpDrops Counter32, agentDaiVlanDhcpPermits Counter32, agentDaiVlanAclDrops Counter32, agentDaiVlanAclPermits Counter32, agentDaiVlanSrcMacFailures Counter32, agentDaiVlanDstMacFailures Counter32, agentDaiVlanIpValidFailures Counter32 } agentDaiVlanStatsIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the VLAN number on which Dynamic ARP Inspection statistics are retrieved." ::= { agentDaiVlanStatsEntry 1 } agentDaiVlanPktsForwarded OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of valid ARP packets forwarded by DAI." ::= { agentDaiVlanStatsEntry 2 } agentDaiVlanPktsDropped OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of invalid ARP packets dropped by DAI." ::= { agentDaiVlanStatsEntry 3 } agentDaiVlanDhcpDrops OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ARP packets that were dropped by DAI as there is no matching DHCP Snooping binding entry found." ::= { agentDaiVlanStatsEntry 4 } agentDaiVlanDhcpPermits OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ARP packets that were forwarded by DAI as there is a matching DHCP Snooping binding entry found." ::= { agentDaiVlanStatsEntry 5 } agentDaiVlanAclDrops OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ARP packets that were dropped by DAI as there is no matching ARP ACL rule found for this Vlan and the static flag is set on this vlan." ::= { agentDaiVlanStatsEntry 6 } agentDaiVlanAclPermits OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ARP packets that were permitted by DAI as there is a matching ARP ACL rule found for this Vlan." ::= { agentDaiVlanStatsEntry 7 } agentDaiVlanSrcMacFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ARP packets that were dropped by DAI as the sender mac address in ARP packet didn't match the source mac in ethernet header." ::= { agentDaiVlanStatsEntry 8 } agentDaiVlanDstMacFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ARP packets that were dropped by DAI as the target mac address in ARP reply packet didn't match the destination mac in ethernet header." ::= { agentDaiVlanStatsEntry 9 } agentDaiVlanIpValidFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ARP packets that were dropped by DAI as the sender IP address in ARP packet or target IP address in ARP reply packet is invalid. Invalid addresses include 0.0.0.0, 255.255.255.255, IP multicast addresses, class E addresses (240.0.0.0/4), loopback addresses (127.0.0.0/8)." ::= { agentDaiVlanStatsEntry 10 } --************ The Dynamic ARP Inspection Interface Config Table ******** agentDaiIfConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDaiIfConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table provides the mechanism to configure the trust state for Dynamic ARP Inspection purpose at each physical interface capable of this feature." ::= { agentDaiConfigGroup 7 } agentDaiIfConfigEntry OBJECT-TYPE SYNTAX AgentDaiIfConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row instance contains the configuration for Dynamic ARP Inspection at each physical interface capable of this feature." INDEX { ifIndex } ::= { agentDaiIfConfigTable 1 } AgentDaiIfConfigEntry ::= SEQUENCE { agentDaiIfTrustEnable TruthValue, agentDaiIfRateLimit Integer32, agentDaiIfBurstInterval Unsigned32 } agentDaiIfTrustEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the interface is trusted for Dynamic ARP Inspection purpose. If this object is set to 'true', the interface is trusted. ARP packets coming to this interface will be forwarded without checking. If this object is set to 'false', the interface is not trusted. ARP packets coming to this interface will be subjected to ARP inspection." DEFVAL { false } ::= { agentDaiIfConfigEntry 1 } agentDaiIfRateLimit OBJECT-TYPE SYNTAX Integer32 (-1|0..300) UNITS "packets per second" MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates rate limit value for Dynamic ARP Inspection purpose. If the incoming rate of ARP packets exceeds the value of this object for consecutively burst interval seconds, ARP packets will be dropped. Value of -1 indicates that there is no rate limit." DEFVAL { 15 } ::= { agentDaiIfConfigEntry 2 } agentDaiIfBurstInterval OBJECT-TYPE SYNTAX Unsigned32 (1..15) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the burst interval value for rate limiting purpose on this interface." DEFVAL { 1 } ::= { agentDaiIfConfigEntry 3 } --************************************************************************************** agentArpAclGroup OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 22 } --************************************************************************************** --*********************** ARP ACL Config Table *********************** agentArpAclTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentArpAclEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the ARP ACL entries" ::= { agentArpAclGroup 1 } agentArpAclEntry OBJECT-TYPE SYNTAX AgentArpAclEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents entry for an ARP ACL" INDEX { agentArpAclName } ::= { agentArpAclTable 1 } AgentArpAclEntry ::= SEQUENCE { agentArpAclName DisplayString, agentArpAclRowStatus RowStatus } agentArpAclName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "Name of the ARP ACL, which must consist of 1 to 31 alphanumeric characters and uniquely identify this ARP ACL. This object must be set to complete a new ARP ACL row instance." ::= { agentArpAclEntry 1 } agentArpAclRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. Entries can not be deleted until all rows in arpAclRuleTable with corresponding values of arpAclIndex have been deleted. active(1) - this ACL instance is active createAndGo(4) - set to this value to create an instance destroy(6) - set to this value to delete an instance" ::= { agentArpAclEntry 2 } --*********************** ARP ACL Rule Config Table *********************** agentArpAclRuleTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentArpAclRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the ARP ACL Rule entries" ::= { agentArpAclGroup 2 } agentArpAclRuleEntry OBJECT-TYPE SYNTAX AgentArpAclRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents entry for a set of ARP ACL-match rules" INDEX { agentArpAclName, agentArpAclRuleMatchSenderIpAddr, agentArpAclRuleMatchSenderMacAddr } ::= { agentArpAclRuleTable 1 } AgentArpAclRuleEntry ::= SEQUENCE { agentArpAclRuleMatchSenderIpAddr IpAddress, agentArpAclRuleMatchSenderMacAddr MacAddress, agentArpAclRuleRowStatus RowStatus } agentArpAclRuleMatchSenderIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Sender IP address match value for the ARP ACL." ::= { agentArpAclRuleEntry 1 } agentArpAclRuleMatchSenderMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Sender MAC address match value for the ARP ACL." ::= { agentArpAclRuleEntry 2 } agentArpAclRuleRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. active(1) - this ACL Rule is active createAndGo(4) - set to this value to create an instance destroy(6) - set to this value to delete an instance" ::= { agentArpAclRuleEntry 3 } --************************************************************************************** agentDhcpSnoopingConfigGroup OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 23 } --************************************************************************************** --************ The DHCP SNOOPING Global Config Table ******** agentDhcpSnoopingAdminMode OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether DHCP Snooping is enabled globally. If this object is set to 'true',admin mode is enabled globally. If this object is set to 'false',admin mode is disabled globally." DEFVAL { false } ::= { agentDhcpSnoopingConfigGroup 1 } agentDhcpSnoopingVerifyMac OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether source Mac address in the received DHCP Message needs to be verified or not. If this object is set to 'true',verifyMac is enabled globally. If this object is set to 'false',verifyMac is disabled globally." DEFVAL { false } ::= { agentDhcpSnoopingConfigGroup 2 } agentDhcpSnoopingVlanConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDhcpSnoopingVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table provides the mechanism to control DHCP SNOOPING per VLAN. When a VLAN is created in a device supporting this table, a corresponding entry of this table will be added." ::= { agentDhcpSnoopingConfigGroup 3 } agentDhcpSnoopingVlanConfigEntry OBJECT-TYPE SYNTAX AgentDhcpSnoopingVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row instance contains the configuration for DHCP SNOOPING at each existing VLAN." INDEX { agentDhcpSnoopingVlanIndex } ::= { agentDhcpSnoopingVlanConfigTable 1 } AgentDhcpSnoopingVlanConfigEntry ::= SEQUENCE { agentDhcpSnoopingVlanIndex VlanIndex, agentDhcpSnoopingVlanEnable TruthValue } agentDhcpSnoopingVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the VLAN number on which DHCP SNOOPING Inspection feature is configured." ::= { agentDhcpSnoopingVlanConfigEntry 1 } agentDhcpSnoopingVlanEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether DHCP SNOOPING is enabled in this VLAN. If this object is set to 'true', DHCP SNOOPING is enabled. If this object is set to 'false', DHCP SNOOPING is disabled." DEFVAL { false } ::= { agentDhcpSnoopingVlanConfigEntry 2 } --************ The DHCP snooping Interface Config Table ******** agentDhcpSnoopingIfConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDhcpSnoopingIfConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table provides the mechanism to configure the trust state for DHCP snooping purpose at each physical interface capable of this feature." ::= { agentDhcpSnoopingConfigGroup 4 } agentDhcpSnoopingIfConfigEntry OBJECT-TYPE SYNTAX AgentDhcpSnoopingIfConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row instance contains the configuration for DHCP snooping at each physical interface capable of this feature." INDEX { ifIndex } ::= { agentDhcpSnoopingIfConfigTable 1 } AgentDhcpSnoopingIfConfigEntry ::= SEQUENCE { agentDhcpSnoopingIfTrustEnable TruthValue, agentDhcpSnoopingIfLogEnable TruthValue, agentDhcpSnoopingIfRateLimit Integer32, agentDhcpSnoopingIfBurstInterval Integer32 } agentDhcpSnoopingIfTrustEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the interface is trusted for DHCP snooping purpose." DEFVAL { false } ::= { agentDhcpSnoopingIfConfigEntry 1 } agentDhcpSnoopingIfLogEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the Logging needs on DHCP snooping validations or not" DEFVAL { false } ::= { agentDhcpSnoopingIfConfigEntry 2 } agentDhcpSnoopingIfRateLimit OBJECT-TYPE SYNTAX Integer32 (-1|0..300) UNITS "packets per second" MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates rate limit value for DHCP Snooping purpose. If the incoming rate of DHCP packets exceeds the value of this object for consecutively burst interval seconds, DHCP packets will be dropped. Value of -1 indicates that there is no rate limit." DEFVAL { -1 } ::= { agentDhcpSnoopingIfConfigEntry 3 } agentDhcpSnoopingIfBurstInterval OBJECT-TYPE SYNTAX Integer32 (-1|1..15) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the burst interval value for rate limiting purpose on this interface. Value of -1 indicates that there is no burst interval." DEFVAL { -1 } ::= { agentDhcpSnoopingIfConfigEntry 4 } --************ The IPSG Interface Config Table ******** agentIpsgIfConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentIpsgIfConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table provides the mechanism to configure the IPSG at each physical interface capable of this feature." ::= { agentDhcpSnoopingConfigGroup 5 } agentIpsgIfConfigEntry OBJECT-TYPE SYNTAX AgentIpsgIfConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row instance contains the configuration for IPSG at each physical interface capable of this feature." INDEX { ifIndex } ::= { agentIpsgIfConfigTable 1 } AgentIpsgIfConfigEntry ::= SEQUENCE { agentIpsgIfVerifySource TruthValue, agentIpsgIfPortSecurity TruthValue } agentIpsgIfVerifySource OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether IP packets received on this interface are filtered based on whether IP Source Guard considers the source IP address to be a valid client address. Setting this variable to false automatically sets agentIpsgIfPortSecurity to false." DEFVAL { false } ::= { agentIpsgIfConfigEntry 1 } agentIpsgIfPortSecurity OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether IP packets received on this interface are filtered based on whether IP Source Guard considers the source MAC address to be a valid client address. The port security option cannot be enabled unless agentIpsgIfVerifySource is also enabled. That is, MAC address filtering cannot be done without also doing IP address filtering. But IP address filtering can be done without MAC address filtering. Once the port security option is enabled, it can only be disabled by disabling agentIpsgIfVerifySource." DEFVAL { false } ::= { agentIpsgIfConfigEntry 2 } --************ The DHCP snooping Statistics Table ******** agentDhcpSnoopingStatsReset OBJECT-TYPE SYNTAX INTEGER { none(0), reset(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear the DHCP snooping statistics on all ports. A value of reset(1) is used to reset the statistics. A read on this object will always return the value none(0). The value none(0) cannot be forcibly set by the administrator." ::= { agentDhcpSnoopingConfigGroup 6 } agentDhcpSnoopingStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDhcpSnoopingStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table provides the mechanism for statics of DHCP snooping." ::= { agentDhcpSnoopingConfigGroup 7 } agentDhcpSnoopingStatsEntry OBJECT-TYPE SYNTAX AgentDhcpSnoopingStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row instance contains the DHCP snooping statistics per VLAN." INDEX { ifIndex } ::= { agentDhcpSnoopingStatsTable 1 } AgentDhcpSnoopingStatsEntry ::= SEQUENCE { agentDhcpSnoopingMacVerifyFailures Counter32, agentDhcpSnoopingInvalidClientMessages Counter32, agentDhcpSnoopingInvalidServerMessages Counter32 } agentDhcpSnoopingMacVerifyFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of failure verifications of client mac address with source mac address" ::= { agentDhcpSnoopingStatsEntry 1 } agentDhcpSnoopingInvalidClientMessages OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of invalid DHCP releases and denay messages" ::= { agentDhcpSnoopingStatsEntry 2 } agentDhcpSnoopingInvalidServerMessages OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of invalid DHCP server mesaages" ::= { agentDhcpSnoopingStatsEntry 3 } --*********************** IPSG static entries Config Table *********************** agentStaticIpsgBindingTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentStaticIpsgBindingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the IPSG static entries" ::= { agentDhcpSnoopingConfigGroup 8 } agentStaticIpsgBinding OBJECT-TYPE SYNTAX AgentStaticIpsgBindingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents a binding in IPSG table" INDEX { agentStaticIpsgBindingIfIndex, agentStaticIpsgBindingVlanId, agentStaticIpsgBindingMacAddr, agentStaticIpsgBindingIpAddr } ::= { agentStaticIpsgBindingTable 1 } AgentStaticIpsgBindingEntry ::= SEQUENCE { agentStaticIpsgBindingIfIndex InterfaceIndex, agentStaticIpsgBindingVlanId VlanIndex, agentStaticIpsgBindingMacAddr MacAddress, agentStaticIpsgBindingIpAddr IpAddress, agentStaticIpsgBindingRowStatus RowStatus } agentStaticIpsgBindingIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-create STATUS current DESCRIPTION "Interface on which this IPSG binding is going to be added." ::= { agentStaticIpsgBinding 1 } agentStaticIpsgBindingVlanId OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-create STATUS current DESCRIPTION " VLAN to whcig this IPSG binding is going to be added." ::= { agentStaticIpsgBinding 2 } agentStaticIpsgBindingMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "MAC address match value for the IPSG Binding." ::= { agentStaticIpsgBinding 3 } agentStaticIpsgBindingIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP address match value for the IPSG Binding." ::= { agentStaticIpsgBinding 4 } agentStaticIpsgBindingRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. active(1) - this IPSG Binding is active createAndGo(4) - set to this value to create an instance destroy(6) - set to this value to delete an instance" ::= { agentStaticIpsgBinding 5 } --*********************** IPSG dynamic entries Config ready only Table *********************** agentDynamicIpsgBindingTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDynamicIpsgBindingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the IPSG dynamic entries" ::= { agentDhcpSnoopingConfigGroup 9 } agentDynamicIpsgBinding OBJECT-TYPE SYNTAX AgentDynamicIpsgBindingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents a binding in IPSG table" INDEX { agentDynamicIpsgBindingIfIndex, agentDynamicIpsgBindingVlanId, agentDynamicIpsgBindingMacAddr, agentDynamicIpsgBindingIpAddr } ::= { agentDynamicIpsgBindingTable 1 } AgentDynamicIpsgBindingEntry ::= SEQUENCE { agentDynamicIpsgBindingIfIndex InterfaceIndex, agentDynamicIpsgBindingVlanId VlanIndex, agentDynamicIpsgBindingMacAddr MacAddress, agentDynamicIpsgBindingIpAddr IpAddress } agentDynamicIpsgBindingIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Interface on which this IPSG binding is added." ::= { agentDynamicIpsgBinding 1 } agentDynamicIpsgBindingVlanId OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION " VLAN to whcig this IPSG binding is going to be added." ::= { agentDynamicIpsgBinding 2 } agentDynamicIpsgBindingMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "MAC address match value for the IPSG Binding." ::= { agentDynamicIpsgBinding 3 } agentDynamicIpsgBindingIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Sender IP address match value for the IPSG Binding." ::= { agentDynamicIpsgBinding 4 } --*********************** DHCP SNOOPING static bindings Config Table *********************** agentStaticDsBindingTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentStaticDsBindingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the DHCP SNOOPING static entries" ::= { agentDhcpSnoopingConfigGroup 10 } agentStaticDsBinding OBJECT-TYPE SYNTAX AgentStaticDsBindingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents a binding in DHCP SNOOPING table" INDEX { agentStaticDsBindingMacAddr } ::= { agentStaticDsBindingTable 1 } AgentStaticDsBindingEntry ::= SEQUENCE { agentStaticDsBindingIfIndex InterfaceIndex, agentStaticDsBindingVlanId VlanId, agentStaticDsBindingMacAddr MacAddress, agentStaticDsBindingIpAddr IpAddress, agentStaticDsBindingRowStatus RowStatus } agentStaticDsBindingIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-create STATUS current DESCRIPTION "Interface on which this DHCP SNOOPING binding is going to be added." ::= { agentStaticDsBinding 1 } agentStaticDsBindingVlanId OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-create STATUS current DESCRIPTION "VLAN to which this DHCP SNOOPING binding is going to be added." ::= { agentStaticDsBinding 2 } agentStaticDsBindingMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "MAC address match value for the DHCP SNOOPING Binding." ::= { agentStaticDsBinding 3 } agentStaticDsBindingIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "IP address match value for the DHCP SNOOPING Binding." ::= { agentStaticDsBinding 4 } agentStaticDsBindingRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. active(1) - this DHCP SNOOPING Binding is active createAndGo(4) - set to this value to create an instance destroy(6) - set to this value to delete an instance" ::= { agentStaticDsBinding 5 } --*********************** DHCP SNOOPING Dynamic bindings Config Table *********************** agentDynamicDsBindingTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDynamicDsBindingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the DHCP SNOOPING Dynamic entries" ::= { agentDhcpSnoopingConfigGroup 11 } agentDynamicDsBinding OBJECT-TYPE SYNTAX AgentDynamicDsBindingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents a binding in DHCP SNOOPING table" INDEX { agentDynamicDsBindingMacAddr } ::= { agentDynamicDsBindingTable 1 } AgentDynamicDsBindingEntry ::= SEQUENCE { agentDynamicDsBindingIfIndex InterfaceIndex, agentDynamicDsBindingVlanId VlanIndex, agentDynamicDsBindingMacAddr MacAddress, agentDynamicDsBindingIpAddr IpAddress, agentDynamicDsBindingLeaseRemainingTime TimeTicks } agentDynamicDsBindingIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Interface on which this DHCP SNOOPING binding is going to be added." ::= { agentDynamicDsBinding 1 } agentDynamicDsBindingVlanId OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION " VLAN to whcig this DHCP SNOOPING binding is going to be added." ::= { agentDynamicDsBinding 2 } agentDynamicDsBindingMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "MAC address match value for the DHCP SNOOPING Binding." ::= { agentDynamicDsBinding 3 } agentDynamicDsBindingIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "IP address match value for the DHCP SNOOPING Binding." ::= { agentDynamicDsBinding 4 } agentDynamicDsBindingLeaseRemainingTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies the period for which the DHCP SNOOPING Binding is valid." ::= { agentDynamicDsBinding 5 } --*********************** DHCP SNOOPING Remote Storage configurations ***********************a agentDhcpSnoopingRemoteFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the file name on the remote machine to save the DHCP Snooping bindings. This will be set only when we have a valid remote IP." ::= { agentDhcpSnoopingConfigGroup 12 } agentDhcpSnoopingRemoteIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the IP address of the remote machine to save the DHCP Snooping bindings. This will be set only when we have a valid file name." ::= { agentDhcpSnoopingConfigGroup 13 } agentDhcpSnoopingStoreInterval OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the perodic time interval to save the DHCP Snooping bindings." ::= { agentDhcpSnoopingConfigGroup 14 } agentDhcpSnoopingStoreTimeout OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the perodic timeout to delete from DHCP Snooping bindings." ::= { agentDhcpSnoopingConfigGroup 15 } --************************************************************************************** -- agentDNSConfigGroup --************************************************************************************** agentDNSConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 18 } agentDNSConfigDomainLookupStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables/Disable DNS-based host name-to-address translation." ::= { agentDNSConfigGroup 1 } agentDNSConfigDefaultDomainName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "Defines a default domain name for incomplete host names at most 64 characters." ::= { agentDNSConfigGroup 2 } agentDNSConfigDefaultDomainNameRemove OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Remove the default domain name for incomplete host name." DEFVAL { disable } ::= { agentDNSConfigGroup 3 } agentDNSConfigDomainNameListTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDNSConfigDomainNameListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines a Table of domain names for incomplete host names" ::= { agentDNSConfigGroup 4 } agentDNSConfigDomainNameListEntry OBJECT-TYPE SYNTAX AgentDNSConfigDomainNameListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines a Entry of domain names for incomplete host names " INDEX { agentDNSConfigDomainNameListIndex } ::= { agentDNSConfigDomainNameListTable 1 } AgentDNSConfigDomainNameListEntry ::= SEQUENCE { agentDNSConfigDomainNameListIndex Integer32, agentDNSDomainName DisplayString, agentDNSDomainNameRemove INTEGER } agentDNSConfigDomainNameListIndex OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Agent Domain Name List Index of the switch" ::= { agentDNSConfigDomainNameListEntry 1 } agentDNSDomainName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Define a domain name for incomplete host name." ::= { agentDNSConfigDomainNameListEntry 2 } agentDNSDomainNameRemove OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Remove a domain name for incomplete host name." DEFVAL { disable } ::= { agentDNSConfigDomainNameListEntry 3 } agentDNSConfigNameServerListTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDNSConfigNameServerListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifie the address of one or more name servers " ::= { agentDNSConfigGroup 5 } agentDNSConfigNameServerListEntry OBJECT-TYPE SYNTAX AgentDNSConfigNameServerListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines a Entry of the address of one or more name servers " INDEX { agentDNSConfigNameServerListIndex } ::= { agentDNSConfigNameServerListTable 1 } AgentDNSConfigNameServerListEntry ::= SEQUENCE { agentDNSConfigNameServerListIndex Integer32, agentDNSConfigNameServer IpAddress, agentDNSConfigRequest Integer32, agentDNSConfigResponse Integer32, agentDNSConfigNameServerRemove INTEGER } agentDNSConfigNameServerListIndex OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Agent name servers List Index of the switch" ::= { agentDNSConfigNameServerListEntry 1 } agentDNSConfigNameServer OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the address of one or more name servers." ::= { agentDNSConfigNameServerListEntry 2 } agentDNSConfigRequest OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Agent Request of name server" ::= { agentDNSConfigNameServerListEntry 3 } agentDNSConfigResponse OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Agent Response of name server" ::= { agentDNSConfigNameServerListEntry 4 } agentDNSConfigNameServerRemove OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Remove a address of name server." DEFVAL { disable } ::= { agentDNSConfigNameServerListEntry 5 } agentIPv6DNSConfigNameServerListTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentIPv6DNSConfigNameServerListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifie the ipv6 address of one or more name servers " ::= { agentDNSConfigGroup 13 } agentIPv6DNSConfigNameServerListEntry OBJECT-TYPE SYNTAX AgentIPv6DNSConfigNameServerListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines a Entry of the ipv6 address of one or more name servers " INDEX { agentIPv6DNSConfigNameServerListIndex } ::= { agentIPv6DNSConfigNameServerListTable 1 } AgentIPv6DNSConfigNameServerListEntry ::= SEQUENCE { agentIPv6DNSConfigNameServerListIndex Integer32, agentIPv6DNSConfigNameServer Ipv6Address, agentIPv6DNSConfigRequest Integer32, agentIPv6DNSConfigResponse Integer32, agentIPv6DNSConfigNameServerRemove INTEGER } agentIPv6DNSConfigNameServerListIndex OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Agent name servers List Index of the switch" ::= { agentIPv6DNSConfigNameServerListEntry 1 } agentIPv6DNSConfigNameServer OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the ipv6 address of one or more name servers." ::= { agentIPv6DNSConfigNameServerListEntry 2 } agentIPv6DNSConfigRequest OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Agent Request of name server" ::= { agentIPv6DNSConfigNameServerListEntry 3 } agentIPv6DNSConfigResponse OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Agent Response of name server" ::= { agentIPv6DNSConfigNameServerListEntry 4 } agentIPv6DNSConfigNameServerRemove OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Remove a ipv6 address of name server." DEFVAL { disable } ::= { agentIPv6DNSConfigNameServerListEntry 5 } agentDNSConfigCacheTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDNSConfigCacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Displays entries in the DNS cache " ::= { agentDNSConfigGroup 6 } agentDNSConfigCacheEntry OBJECT-TYPE SYNTAX AgentDNSConfigCacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Displays entries in the DNS cache " INDEX { agentDNSConfigCacheIndex } ::= { agentDNSConfigCacheTable 1 } AgentDNSConfigCacheEntry ::= SEQUENCE { agentDNSConfigCacheIndex Integer32, agentDNSConfigDomainName DisplayString, agentDNSConfigIpAddress IpAddress, agentDNSConfigTTL Integer32, agentDNSConfigFlag Integer32 } agentDNSConfigCacheIndex OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Agent DNS cache Index of the switch" ::= { agentDNSConfigCacheEntry 1 } agentDNSConfigDomainName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Displays one or more Domain name servers." ::= { agentDNSConfigCacheEntry 2 } agentDNSConfigIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the address of one or more name servers." ::= { agentDNSConfigCacheEntry 3 } agentDNSConfigTTL OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the TTL of one or more name servers." ::= { agentDNSConfigCacheEntry 4 } agentDNSConfigFlag OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the Flag of one or more name servers." ::= { agentDNSConfigCacheEntry 5 } agentIPv6DNSConfigCacheTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentIPv6DNSConfigCacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Displays entries in the DNS cache " ::= { agentDNSConfigGroup 14 } agentIPv6DNSConfigCacheEntry OBJECT-TYPE SYNTAX AgentIPv6DNSConfigCacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Displays entries in the DNS cache " INDEX { agentIPv6DNSConfigCacheIndex } ::= { agentIPv6DNSConfigCacheTable 1 } AgentIPv6DNSConfigCacheEntry ::= SEQUENCE { agentIPv6DNSConfigCacheIndex Integer32, agentIPv6DNSConfigDomainName DisplayString, agentIPv6DNSConfigIpAddress Ipv6Address, agentIPv6DNSConfigTTL Integer32, agentIPv6DNSConfigFlag Integer32 } agentIPv6DNSConfigCacheIndex OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Agent DNS cache Index of the switch" ::= { agentIPv6DNSConfigCacheEntry 1 } agentIPv6DNSConfigDomainName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Displays one or more Domain name servers." ::= { agentIPv6DNSConfigCacheEntry 2 } agentIPv6DNSConfigIpAddress OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the ipv6 address of one or more name servers." ::= { agentIPv6DNSConfigCacheEntry 3 } agentIPv6DNSConfigTTL OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the TTL of one or more name servers." ::= { agentIPv6DNSConfigCacheEntry 4 } agentIPv6DNSConfigFlag OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the Flag of one or more name servers." ::= { agentIPv6DNSConfigCacheEntry 5 } agentDNSConfigHostTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDNSConfigHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Displays the static host name-to-address mapping table" ::= { agentDNSConfigGroup 7 } agentDNSConfigHostEntry OBJECT-TYPE SYNTAX AgentDNSConfigHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Displays the static host name-to-address mapping table" INDEX { agentDNSConfigHostIndex } ::= { agentDNSConfigHostTable 1 } AgentDNSConfigHostEntry ::= SEQUENCE { agentDNSConfigHostIndex Integer32, agentDNSConfigHostName DisplayString, agentDNSConfigHostIpAddress InetAddress, agentDNSConfigHostNameRemove INTEGER } agentDNSConfigHostIndex OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Agent Host Index of the switch" ::= { agentDNSConfigHostEntry 1 } agentDNSConfigHostName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Display the static host name." ::= { agentDNSConfigHostEntry 2 } agentDNSConfigHostIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Display the static host IP/IPv6 address." ::= { agentDNSConfigHostEntry 3 } agentDNSConfigHostNameRemove OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Remove static host name." DEFVAL { disable } ::= { agentDNSConfigHostEntry 4 } agentIPv6DNSConfigHostTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentIPv6DNSConfigHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Displays the static host name-to-address mapping table" ::= { agentDNSConfigGroup 15 } agentDNSConfigSourceInterface OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-write STATUS current DESCRIPTION "A source-interface selection on an Interface Index (like vlan based routing interface, port based routing interface, loopback interface, tunnel interface). A non-zero value indicates ifIndex for the corresponding interface entry in the ifTable is selected. A zero value indicates the source-interface un-selection." ::= {agentDNSConfigGroup 16 } agentIPv6DNSConfigHostEntry OBJECT-TYPE SYNTAX AgentIPv6DNSConfigHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Displays the static host name-to-address mapping table Obsolete, move to agentDNSConfigHostTable" INDEX { agentIPv6DNSConfigHostIndex } ::= { agentIPv6DNSConfigHostTable 1 } AgentIPv6DNSConfigHostEntry ::= SEQUENCE { agentIPv6DNSConfigHostIndex Integer32, agentIPv6DNSConfigHostName DisplayString, agentIPv6DNSConfigHostIpAddress Ipv6Address, agentIPv6DNSConfigHostNameRemove INTEGER } agentIPv6DNSConfigHostIndex OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS obsolete DESCRIPTION "Agent Host Index of the switch" ::= { agentIPv6DNSConfigHostEntry 1 } agentIPv6DNSConfigHostName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS obsolete DESCRIPTION "Display the static host name." ::= { agentIPv6DNSConfigHostEntry 2 } agentIPv6DNSConfigHostIpAddress OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-create STATUS obsolete DESCRIPTION "Display the static host IPv6 address." ::= { agentIPv6DNSConfigHostEntry 3 } agentIPv6DNSConfigHostNameRemove OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Remove static host name." DEFVAL { disable } ::= { agentIPv6DNSConfigHostEntry 4 } agentDNSConfigClearDomainNameList OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables/Disable Clear all entries domain names for incomplete host names." DEFVAL { disable } ::= { agentDNSConfigGroup 8 } agentDNSConfigClearCache OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables/Disable Clear all entries from the DNS cache." DEFVAL { disable } ::= { agentDNSConfigGroup 9 } agentDNSConfigClearHosts OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables/Disable Clear all static host name-to-address mapping." DEFVAL { disable } ::= { agentDNSConfigGroup 10 } agentDNSConfigClearDNS OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables/Disable set the DNS configuration to default value." DEFVAL { disable } ::= { agentDNSConfigGroup 11 } agentDNSConfigClearDNSCounters OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables/Disable Clear Request and Response of all DNS ." DEFVAL { disable } ::= { agentDNSConfigGroup 12 } --************************************************************************************** -- agentDhcpL2RelayConfigGroup --************************************************************************************** agentDhcpL2RelayConfigGroup OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 24 } --************************************************************************************** agentDhcpL2RelayAdminMode OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether DHCP L2 Relay is enabled globally. If this object is set to 'true',admin mode is enabled globally. If this object is set to 'false',admin mode is disabled globally." DEFVAL { false } ::= { agentDhcpL2RelayConfigGroup 1 } --************ The DHCP L2Relay Interface Config Table ******** agentDhcpL2RelayIfConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDhcpL2RelayIfConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table provides the mechanism to enable/disable and configure the trust state for DHCP L2Relay purpose at each physical interface capable of this feature." ::= { agentDhcpL2RelayConfigGroup 2 } agentDhcpL2RelayIfConfigEntry OBJECT-TYPE SYNTAX AgentDhcpL2RelayIfConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row instance contains the configuration for DHCP L2 Relay at each physical interface capable of this feature." INDEX { ifIndex } ::= { agentDhcpL2RelayIfConfigTable 1 } AgentDhcpL2RelayIfConfigEntry ::= SEQUENCE { agentDhcpL2RelayIfEnable TruthValue, agentDhcpL2RelayIfTrustEnable TruthValue } agentDhcpL2RelayIfEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the DHCP L2Relay is enabled or not" DEFVAL { false } ::= { agentDhcpL2RelayIfConfigEntry 1 } agentDhcpL2RelayIfTrustEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the interface is trusted for DHCP L2 Relay purpose." DEFVAL { false } ::= { agentDhcpL2RelayIfConfigEntry 2 } --************ The DHCP L2 Relay VLAN Config Table ******** agentDhcpL2RelayVlanConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDhcpL2RelayVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table provides the mechanism to control DHCP L2 Relay per VLAN. When a VLAN is created in a device supporting this table, a corresponding entry of this table will be added." ::= { agentDhcpL2RelayConfigGroup 3 } agentDhcpL2RelayVlanConfigEntry OBJECT-TYPE SYNTAX AgentDhcpL2RelayVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row instance contains the configuration for DHCP L2 Relay at each existing VLAN." INDEX { agentDhcpL2RelayVlanIndex } ::= { agentDhcpL2RelayVlanConfigTable 1 } AgentDhcpL2RelayVlanConfigEntry ::= SEQUENCE { agentDhcpL2RelayVlanIndex VlanIndex, agentDhcpL2RelayVlanEnable TruthValue, agentDhcpL2RelayCircuitIdVlanEnable TruthValue, agentDhcpL2RelayRemoteIdVlanEnable DisplayString } agentDhcpL2RelayVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the VLAN number on which DHCP L2 Relay feature is configured." ::= { agentDhcpL2RelayVlanConfigEntry 1 } agentDhcpL2RelayVlanEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether DHCP L2 Relay is enabled in this VLAN. If this object is set to 'true', DHCP L2 Relay is enabled. If this object is set to 'false', DHCP L2 Relay is disabled." DEFVAL { false } ::= { agentDhcpL2RelayVlanConfigEntry 2 } agentDhcpL2RelayCircuitIdVlanEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether DHCP CircuitId is enabled for L2 relaying in this VLAN. If this object is set to 'true', DHCP CircuitId is enabled. If this object is set to 'false', DHCP CircuitId is disabled." DEFVAL { false } ::= { agentDhcpL2RelayVlanConfigEntry 3 } agentDhcpL2RelayRemoteIdVlanEnable OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "When this object is set with a non-empty string, DHCP RemoteId is enabled for L2 relaying in this VLAN." ::= { agentDhcpL2RelayVlanConfigEntry 4 } --************ The DHCP L2 Relay Statistics Table ******** agentDhcpL2RelayStatsReset OBJECT-TYPE SYNTAX INTEGER { none(0), reset(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear the DHCP L2Relay statistics on all ports. A value of reset(1) is used to reset the statistics. A read on this object will always return the value none(0). The value none(0) cannot be forcibly set by the administrator." ::= { agentDhcpL2RelayConfigGroup 6 } agentDhcpL2RelayStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentDhcpL2RelayStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table provides the mechanism for statics of DHCP L2 Relay." ::= { agentDhcpL2RelayConfigGroup 7 } agentDhcpL2RelayStatsEntry OBJECT-TYPE SYNTAX AgentDhcpL2RelayStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row instance contains the DHCP L2Relay statistics per interface." INDEX { ifIndex } ::= { agentDhcpL2RelayStatsTable 1 } AgentDhcpL2RelayStatsEntry ::= SEQUENCE { agentDhcpL2RelayUntrustedSrvrMsgsWithOptn82 Counter32, agentDhcpL2RelayUntrustedClntMsgsWithOptn82 Counter32, agentDhcpL2RelayTrustedSrvrMsgsWithoutOptn82 Counter32, agentDhcpL2RelayTrustedClntMsgsWithoutOptn82 Counter32 } agentDhcpL2RelayUntrustedSrvrMsgsWithOptn82 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of DHCP server messages received with Option-82 field on the untrusted interface." ::= { agentDhcpL2RelayStatsEntry 1 } agentDhcpL2RelayUntrustedClntMsgsWithOptn82 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of DHCP client messages received with Option-82 field on the untrusted interface." ::= { agentDhcpL2RelayStatsEntry 2 } agentDhcpL2RelayTrustedSrvrMsgsWithoutOptn82 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of DHCP server messages received without Option-82 field on the trusted interface." ::= { agentDhcpL2RelayStatsEntry 3 } agentDhcpL2RelayTrustedClntMsgsWithoutOptn82 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of DHCP client messages received without Option-82 field on the trusted interface." ::= { agentDhcpL2RelayStatsEntry 4 } --************************************************************************************** -- agentSwitchVoiceVLANGroup -- --************************************************************************************** agentSwitchVoiceVLANGroup OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 25 } agentSwitchVoiceVlanDeviceTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSwitchVoiceVlanDeviceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the Voice Vlan device entries." ::= { agentSwitchVoiceVLANGroup 2 } agentSwitchVoiceVlanDeviceEntry OBJECT-TYPE SYNTAX AgentSwitchVoiceVlanDeviceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents entry for a Voice Device on the interface." INDEX { agentSwitchVoiceVlanInterfaceNum, agentSwitchVoiceVlanDeviceMacAddress } ::= { agentSwitchVoiceVlanDeviceTable 1 } AgentSwitchVoiceVlanDeviceEntry ::= SEQUENCE { agentSwitchVoiceVlanInterfaceNum Integer32, agentSwitchVoiceVlanDeviceMacAddress MacAddress } agentSwitchVoiceVlanInterfaceNum OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The interface number of this interface." ::= {agentSwitchVoiceVlanDeviceEntry 1 } agentSwitchVoiceVlanDeviceMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Voice Device Mac address" ::= { agentSwitchVoiceVlanDeviceEntry 2 } --************************************************************************************** -- agentSwitchAddresConflictGroup -- --************************************************************************************** agentSwitchAddressConflictGroup OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 26 } agentSwitchAddressConflictDetectionStatus OBJECT-TYPE SYNTAX INTEGER { false(0), true(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Displays if an address conflict was detected on the switch since the last reset of the status. Set to 'true' if detected, 'false' otherwise." ::= { agentSwitchAddressConflictGroup 1 } agentSwitchAddressConflictDetectionStatusReset OBJECT-TYPE SYNTAX INTEGER { none(0), reset(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear the last address conflict detection status in the switch. A value of reset(1) is used to reset the status. A read on this object always returns the value none (0). The value none (0) cannot be forcibly set by the administrator." ::= { agentSwitchAddressConflictGroup 2 } agentSwitchLastConflictingIPAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The reported conflicting IP address on the switch since the last reset of the conflict detection status." ::= { agentSwitchAddressConflictGroup 3 } agentSwitchLastConflictingMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address of the host corresponding to the reported conflicting IP address on the switch since the last reset of the conflict detection status." ::= { agentSwitchAddressConflictGroup 4 } agentSwitchLastConflictReportedTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Time since the last address conflict was detected. It is displayed in days, hours, minutes and seconds. It is set to a valid value only when the conflict detection status is 'true'." ::= { agentSwitchAddressConflictGroup 5 } agentSwitchConflictIPAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The IP address on the switch reported to have a conflict with another host's IP address." ::= { agentSwitchAddressConflictGroup 6 } agentSwitchConflictMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The MAC address of the host that has an IP address conflicting with the IP address on the switch." ::= { agentSwitchAddressConflictGroup 7 } agentSwitchAddressConflictDetectionRun OBJECT-TYPE SYNTAX INTEGER { none(0), run(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Trigger the action to run the active address conflict detection. A value of run(1) is used to issue the action command. A read on this object always returns the value none(0). The value none (0) cannot be forcibly set by the administrator." ::= { agentSwitchAddressConflictGroup 8 } --************************************************************************************* -- Traps --************************************************************************************** switchingTraps OBJECT IDENTIFIER ::= { switching 50 } multipleUsersTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "This trap is sent when more than one user is logged in with administrative access. Only applies to CLI interface." ::= { switchingTraps 1 } broadcastStormStartTrap NOTIFICATION-TYPE STATUS obsolete DESCRIPTION "This trap is sent when a broadcast storm is detected." ::= { switchingTraps 2 } broadcastStormEndTrap NOTIFICATION-TYPE STATUS obsolete DESCRIPTION "This trap is sent when a broadcast storm is no longer detected." ::= { switchingTraps 3 } linkFailureTrap NOTIFICATION-TYPE STATUS obsolete DESCRIPTION "" ::= { switchingTraps 4 } vlanRequestFailureTrap NOTIFICATION-TYPE OBJECTS { dot1qVlanIndex } STATUS obsolete DESCRIPTION "" ::= { switchingTraps 5 } vlanDeleteLastTrap NOTIFICATION-TYPE OBJECTS { dot1qVlanIndex } STATUS current DESCRIPTION "Trap is sent when attempting to delete the last configured VLAN or the Default VLAN." ::= { switchingTraps 6 } vlanDefaultCfgFailureTrap NOTIFICATION-TYPE OBJECTS { dot1qVlanIndex } STATUS current DESCRIPTION "Trap is sent if there are failures in resetting VLAN configuration to defaults." ::= { switchingTraps 7 } vlanRestoreFailureTrap NOTIFICATION-TYPE OBJECTS { dot1qVlanIndex } STATUS obsolete DESCRIPTION "" ::= { switchingTraps 8 } fanFailureTrap NOTIFICATION-TYPE STATUS obsolete DESCRIPTION "" ::= { switchingTraps 9 } stpInstanceNewRootTrap NOTIFICATION-TYPE OBJECTS { agentStpMstId } STATUS current DESCRIPTION "Trap is sent when this machine is a new STP Root when there is more than one STP instance." ::= { switchingTraps 10 } stpInstanceTopologyChangeTrap NOTIFICATION-TYPE OBJECTS { agentStpMstId } STATUS current DESCRIPTION "Trap is sent when there is a STP topology change when there is more than one STP instance." ::= { switchingTraps 11 } powerSupplyStatusChangeTrap NOTIFICATION-TYPE STATUS obsolete DESCRIPTION "" ::= { switchingTraps 12 } failedUserLoginTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "Trap is sent when a user fails to authenticate via the CLI or Web interfaces." ::= { switchingTraps 13 } temperatureTooHighTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "temperatureTooHighTrap" ::= { switchingTraps 14 } stormControlDetectedTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "stormControlDetectedTrap" ::= { switchingTraps 15 } stormControlStopTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "stormControlStopTrap" ::= { switchingTraps 16 } userLockoutTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "Trap is sent when a user account is locked due to consecutive failed login attempts via the CLI or Web interfaces beyond the allowed limit." ::= { switchingTraps 17 } daiIntfErrorDisabledTrap NOTIFICATION-TYPE OBJECTS { ifIndex } STATUS current DESCRIPTION "Trap is sent once an interface is error disabled by DAI when the incoming packet rate exceeded configured rate limit during a burst-interval." ::= { switchingTraps 18 } stpInstanceLoopInconsistentStartTrap NOTIFICATION-TYPE OBJECTS { agentStpMstId, ifIndex } STATUS current DESCRIPTION "Trap is sent when this port in this STP instance enters loop inconsistent state upon failure to receive a BPDU." ::= { switchingTraps 19 } stpInstanceLoopInconsistentEndTrap NOTIFICATION-TYPE OBJECTS { agentStpMstId, ifIndex } STATUS current DESCRIPTION "Trap is sent when this port in this STP instance exits loop inconsistent state upon reception of a BPDU." ::= { switchingTraps 20 } dhcpSnoopingIntfErrorDisabledTrap NOTIFICATION-TYPE OBJECTS { ifIndex } STATUS current DESCRIPTION "Trap is sent once an interface is error disabled by DHCP Snooping when the incoming packet rate exceeded configured rate limit during a burst-interval." ::= { switchingTraps 21 } noStartupConfigTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "Trap is sent when startup-config file exists and SSH is enabled." ::= { switchingTraps 22 } agentSwitchIpAddressConflictTrap NOTIFICATION-TYPE OBJECTS { agentSwitchConflictIPAddr, agentSwitchConflictMacAddr } STATUS current DESCRIPTION "IP address conflict trap signifies the reception of an ARP from another host in the LAN that has conflicting IP address." ::= { switchingTraps 23 } agentSwitchCpuRisingThresholdTrap NOTIFICATION-TYPE OBJECTS { agentSwitchCpuProcessRisingThreshold, agentSwitchCpuProcessName } STATUS current DESCRIPTION "Trap is sent when the total CPU utilization exceeds CPU Rising utilization threshold over the configured Rising threshold interval." ::= { switchingTraps 24 } agentSwitchCpuFallingThresholdTrap NOTIFICATION-TYPE OBJECTS { agentSwitchCpuProcessFallingThreshold } STATUS current DESCRIPTION "Trap is sent when the total CPU utilization falls below CPU Falling utilization threshold over the configured falling threshold interval." ::= { switchingTraps 25 } agentSwitchCpuFreeMemBelowThresholdTrap NOTIFICATION-TYPE OBJECTS { agentSwitchCpuProcessFreeMemoryThreshold } STATUS current DESCRIPTION "Trap is sent when CPU Free Memory falls below the configured threshold." ::= { switchingTraps 26 } agentSwitchCpuFreeMemAboveThresholdTrap NOTIFICATION-TYPE OBJECTS { agentSwitchCpuProcessFreeMemoryThreshold } STATUS current DESCRIPTION "Trap is sent when CPU Free Memory rises to 10% above the configured threshold." ::= { switchingTraps 27 } configChangedTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "Trap is sent when system config changed." ::= { switchingTraps 28 } agentSwitchCpuMemInvalidTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "Trap is sent when Memory is invalid." ::= { switchingTraps 29 } --***************************************************************************************** -- sdmTemplate -- -- This provides configuration and status of the Switch Database Management Template -- feature. -- --***************************************************************************************** agentSdmPreferConfigEntry OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 27 } agentSdmPreferCurrentTemplate OBJECT-TYPE SYNTAX INTEGER { dualIPv4andIPv6(1), ipv4RoutingDefault(2), ipv4DataCenter(3) } MAX-ACCESS read-only STATUS current DESCRIPTION " Displays the current active SDM Template." ::= { agentSdmPreferConfigEntry 1 } agentSdmPreferNextTemplate OBJECT-TYPE SYNTAX INTEGER { default(0), dualIPv4andIPv6(1), ipv4RoutingDefault(2), ipv4DataCenter(3) } MAX-ACCESS read-write STATUS current DESCRIPTION " Configures the next active template. It will be active only after the next reboot. To revert to the default template after the next reboot, use the option default(0)." ::= { agentSdmPreferConfigEntry 2 } --******************************************************************************************* agentSdmTemplateSummaryTable OBJECT IDENTIFIER ::= { agentSwitchConfigGroup 28 } agentSdmTemplateTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentSdmTemplateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Displays Switch Database Management Template Information." ::= { agentSdmTemplateSummaryTable 1 } agentSdmTemplateEntry OBJECT-TYPE SYNTAX AgentSdmTemplateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a SDM Template table entry." INDEX { agentSdmTemplateId } ::= { agentSdmTemplateTable 1 } AgentSdmTemplateEntry::= SEQUENCE { agentSdmTemplateId INTEGER, agentArpEntries INTEGER, agentIPv4UnicastRoutes INTEGER, agentIPv6NdpEntries INTEGER, agentIPv6UnicastRoutes INTEGER, agentEcmpNextHops INTEGER, agentIPv4MulticastRoutes INTEGER, agentIPv6MulticastRoutes INTEGER } agentSdmTemplateId OBJECT-TYPE SYNTAX INTEGER { dualIPv4andIPv6(1), ipv4RoutingDefault(2), ipv4DataCenter(3) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SDM Template type this instance is associated with." ::= { agentSdmTemplateEntry 1 } agentArpEntries OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of entries in the IPv4 Address Resolution Protocol (ARP) cache for routing interfaces." ::= { agentSdmTemplateEntry 2 } agentIPv4UnicastRoutes OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of IPv4 unicast forwarding table entries." ::= { agentSdmTemplateEntry 3 } agentIPv6NdpEntries OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of IPv6 Neighbor Discovery Protocol (NDP) cache entries." ::= { agentSdmTemplateEntry 4 } agentIPv6UnicastRoutes OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of IPv6 unicast forwarding table entries." ::= { agentSdmTemplateEntry 5 } agentEcmpNextHops OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of Equal cost next hops that can be installed in the IPv4 and IPv6 unicast forwarding tables." ::= { agentSdmTemplateEntry 6 } agentIPv4MulticastRoutes OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of IPv4 multicast forwarding table entries." ::= { agentSdmTemplateEntry 7 } agentIPv6MulticastRoutes OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of IPv6 multicast forwarding table entries." ::= { agentSdmTemplateEntry 8 } --************************************************************************************** agentDhcpClientOptionsConfigGroup OBJECT IDENTIFIER ::= { agentConfigGroup 21 } --************************************************************************************** --************************************************************************************** agentVendorClassOptionConfigGroup OBJECT IDENTIFIER ::= { agentDhcpClientOptionsConfigGroup 1 } --************************************************************************************** agentDhcpClientVendorClassIdMode OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether DHCP Vendor Classifier Id Option (60) is enabled for DHCP Network Client. If this object is set to 'true', DHCP Vendor Classifier Id mode is enabled globally. If this object is set to 'false', DHCP Vendor Classifier Id mode is disabled globally." DEFVAL { false } ::= { agentVendorClassOptionConfigGroup 1 } agentDhcpClientVendorClassIdString OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "When this object is set with a non-empty string, the DHCP Vendor Classifier Id Option (60) string is enabled for DHCP Network Client." ::= { agentVendorClassOptionConfigGroup 2 } --************************************************************************************** -- agentExecAccountingGroup -> Contains MIB objects to configure ExecAccounting method lists -- --************************************************************************************** agentExecAccountingGroup OBJECT IDENTIFIER ::= { agentConfigGroup 29 } agentExecAccountingListCreate OBJECT-TYPE SYNTAX DisplayString (SIZE(0|1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "ExecAccounting List Create if set to a non empty string, creates a new ExecAccounting List for configuration." ::= { agentExecAccountingGroup 1 } --************************************************************************************** agentExecAccountingListTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentExecAccountingListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "ExecAccounting Method List table." ::= { agentExecAccountingGroup 2 } agentExecAccountingListEntry OBJECT-TYPE SYNTAX AgentExecAccountingListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "ExecAccounting Method List Entry." INDEX { agentExecAccountingListIndex } ::= { agentExecAccountingListTable 1 } AgentExecAccountingListEntry ::= SEQUENCE { agentExecAccountingListIndex Unsigned32, agentExecAccountingListName DisplayString, agentExecAccountingMethodType INTEGER, agentExecAccountingListMethod1 INTEGER, agentExecAccountingListMethod2 INTEGER, agentExecAccountingListStatus RowStatus } agentExecAccountingListIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "ExecAccounting List Index Unique number used for indexing into this table." ::= { agentExecAccountingListEntry 1 } agentExecAccountingListName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-only STATUS current DESCRIPTION " Unique name used to identify the ExecAccounting List from other tables." ::= { agentExecAccountingListEntry 2 } agentExecAccountingMethodType OBJECT-TYPE SYNTAX INTEGER { undefined(0), start-stop(1), stop-only(2), none(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "ExecAccounting Method Type Configures the method type to use when this ExecAccounting list is specified." ::= { agentExecAccountingListEntry 3 } agentExecAccountingListMethod1 OBJECT-TYPE SYNTAX INTEGER { undefined(0), tacacs(1), radius(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "ExecAccounting List Method 1 Configures the authentication method to use when this list is specified." ::= { agentExecAccountingListEntry 4 } agentExecAccountingListMethod2 OBJECT-TYPE SYNTAX INTEGER { undefined(0), tacacs(1), radius(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "ExecAccounting List Method 2 Configures the authentication method to use when this list is specified." ::= { agentExecAccountingListEntry 5 } agentExecAccountingListStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of the ExecAccounting List. Supported values: active(1) - indicates a valid ExecAccounting List destroy(6) - removes the ExecAccounting List." ::= { agentExecAccountingListEntry 6 } --************************************************************************************** -- agentCmdsAccountingGroup -> Contains MIB objects to configure CmdsAccounting method lists -- --************************************************************************************** agentCmdsAccountingGroup OBJECT IDENTIFIER ::= { agentConfigGroup 30 } agentCmdsAccountingListCreate OBJECT-TYPE SYNTAX DisplayString (SIZE(0|1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "CmdsAccounting List Create if set to a non empty string, creates a new CmdsAccounting List for configuration." ::= { agentCmdsAccountingGroup 1 } --************************************************************************************** agentCmdsAccountingListTable OBJECT-TYPE SYNTAX SEQUENCE OF AgentCmdsAccountingListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "CmdsAccounting Method List table." ::= { agentCmdsAccountingGroup 2 } agentCmdsAccountingListEntry OBJECT-TYPE SYNTAX AgentCmdsAccountingListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "CmdsAccounting Method List Entry." INDEX { agentCmdsAccountingListIndex } ::= { agentCmdsAccountingListTable 1 } AgentCmdsAccountingListEntry ::= SEQUENCE { agentCmdsAccountingListIndex Unsigned32, agentCmdsAccountingListName DisplayString, agentCmdsAccountingMethodType INTEGER, agentCmdsAccountingListMethod1 INTEGER, agentCmdsAccountingListStatus RowStatus } agentCmdsAccountingListIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "CmdsAccounting List Index Unique number used for indexing into this table." ::= { agentCmdsAccountingListEntry 1 } agentCmdsAccountingListName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-only STATUS current DESCRIPTION " Unique name used to identify the CmdsAccounting List from other tables." ::= { agentCmdsAccountingListEntry 2 } agentCmdsAccountingMethodType OBJECT-TYPE SYNTAX INTEGER { undefined(0), start-stop(1), stop-only(2), none(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "CmdsAccounting Method Type Configures the method type to use when this CmdsAccounting list is specified." ::= { agentCmdsAccountingListEntry 3 } agentCmdsAccountingListMethod1 OBJECT-TYPE SYNTAX INTEGER { undefined(0), tacacs(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "CmdsAccounting List Method 1 Configures the authentication method to use when this list is specified." ::= { agentCmdsAccountingListEntry 4 } agentCmdsAccountingListStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of the CmdsAccounting List. Supported values: active(1) - indicates a valid CmdsAccounting List destroy(6) - removes the CmdsAccounting List." ::= { agentCmdsAccountingListEntry 5 } END