NEWTEC-TSANALYSER-MIB DEFINITIONS ::= BEGIN IMPORTS Unsigned32, Counter64, Integer32, MODULE-IDENTITY, OBJECT-IDENTITY, OBJECT-TYPE FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF NtcAlarmState, NtcEnable FROM NEWTEC-TC-MIB ntcFunction FROM NEWTEC-MAIN-MIB; -- -- Module Identification -- ntcTsAnalyser MODULE-IDENTITY LAST-UPDATED "201804041000Z" ORGANIZATION "Newtec Cy" CONTACT-INFO "Newtec Cy Postal: Newtec Cy Laarstraat 5 B-9100 Sint-Niklaas Belgium Tel: +32 3 780 65 00 Fax: +32 3 780 65 49 Web: www.newtec.be E-mail: techsupport@newtec.be" DESCRIPTION "Newtec modular MIB containing definitions for transport stream analyser functionality." REVISION "201804041000Z" DESCRIPTION "Cosmetic change in units of error counters" REVISION "201707101200Z" DESCRIPTION "ntcTsAnlyEPid added" REVISION "201612051200Z" DESCRIPTION "ntcTsAnlyPidCtuCntErrorCntr column added to ntcTsAnlyPid table" REVISION "201409090900Z" DESCRIPTION "descriptions adapted" REVISION "201303271000Z" DESCRIPTION "Release for M6100 R1.3" REVISION "201206281200Z" DESCRIPTION "Release for M6100 R1.2" ::= { ntcFunction 1400 } -- -- Top-Level Structure -- -- ntcTsAnalyser content ntcTsAnlyObjects OBJECT-IDENTITY STATUS current DESCRIPTION "Container holding ntcTsAnlyObjects definitions." ::= { ntcTsAnalyser 1 } ntcTsAnlyConformance OBJECT-IDENTITY STATUS current DESCRIPTION "Conformance requirements." ::= { ntcTsAnalyser 2 } -- ntcTsAnlyObjects content ntcTsAnlyAlarm OBJECT-IDENTITY STATUS current DESCRIPTION "Container holding ntcTsAnlyAlarm definitions." ::= { ntcTsAnlyObjects 6 } -- ntcTsAnlyConformance content ntcTsAnlyConfCompliance OBJECT-IDENTITY STATUS current DESCRIPTION "Device compliance statements." ::= { ntcTsAnlyConformance 1 } ntcTsAnlyConfGroup OBJECT-IDENTITY STATUS current DESCRIPTION "Groups used by device compliance statements." ::= { ntcTsAnlyConformance 2 } -- -- Managed Objects -- ntcTsAnlyEble OBJECT-TYPE SYNTAX NtcEnable MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable Transport Stream Analyzer." DEFVAL { off } ::= { ntcTsAnlyObjects 1 } ntcTsAnlyReset OBJECT-TYPE SYNTAX INTEGER { running(0), reset(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Reset Transport Stream Analyzer" DEFVAL { running } ::= { ntcTsAnlyObjects 2 } ntcTsAnlyEstimatedTsRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Displays the measured TS bit rate in bps. Current devices support a range of 0 to 2500000000 bps." ::= { ntcTsAnlyObjects 3 } ntcTsAnlyPidTable OBJECT-TYPE SYNTAX SEQUENCE OF NtcTsAnlyPidEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing all detected PID's of the incoming traffic stream with corresponding measurements." ::= { ntcTsAnlyObjects 4 } ntcTsAnlyPidEntry OBJECT-TYPE SYNTAX NtcTsAnlyPidEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of the ntcTsAnlyPidTable." INDEX { ntcTsAnlyPidPid } ::= { ntcTsAnlyPidTable 1 } NtcTsAnlyPidEntry ::= SEQUENCE { ntcTsAnlyPidPid Unsigned32, ntcTsAnlyPidType INTEGER, ntcTsAnlyPidPIDRate Unsigned32, ntcTsAnlyPidContinuityError INTEGER, ntcTsAnlyPidTransportError INTEGER, ntcTsAnlyPidCtuCntErrorCntr Counter64 } ntcTsAnlyPidPid OBJECT-TYPE SYNTAX Unsigned32 (0..8190) MAX-ACCESS not-accessible STATUS current DESCRIPTION "PID" ::= { ntcTsAnlyPidEntry 1 } ntcTsAnlyPidType OBJECT-TYPE SYNTAX INTEGER { others(0), video(1), audio(2), privateSection(3), pesPrivate(4), mheg(5), dsmCc(6), h2221(7), mpe(8), auxiliary(9), slOrFlexMux(10), sdp(11), metadata(12), ipmp(13), userPrivate(14), pat(15), cat(16), tsdt(17), nitOrSt(18), sdtOrBatOrSt(19), eitOrStCit(20), rstOrSt(21), tdtOrTotOrSt(22), netwSync(23), rnt(24), inband(25), measurement(26), dit(27), sit(28), null(29), othersOrGhost(30), pmt(31), visual(32), srm(33), ecm(34), emm(35) } MAX-ACCESS read-only STATUS current DESCRIPTION "PID Type" ::= { ntcTsAnlyPidEntry 2 } ntcTsAnlyPidPIDRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "PID Rate for a specific stream." ::= { ntcTsAnlyPidEntry 3 } ntcTsAnlyPidContinuityError OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Continuity Count Error" ::= { ntcTsAnlyPidEntry 4 } ntcTsAnlyPidTransportError OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Transport Error" ::= { ntcTsAnlyPidEntry 5 } ntcTsAnlyPidCtuCntErrorCntr OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of packets with a continuity count error." ::= { ntcTsAnlyPidEntry 6 } ntcTsAnlyPcrPidTable OBJECT-TYPE SYNTAX SEQUENCE OF NtcTsAnlyPcrPidEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of PCR PID's with detailled time measurements." ::= { ntcTsAnlyObjects 5 } ntcTsAnlyPcrPidEntry OBJECT-TYPE SYNTAX NtcTsAnlyPcrPidEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of the ntcTsAnlyPcrPidTable." INDEX { ntcTsAnlyPcrPidPid } ::= { ntcTsAnlyPcrPidTable 1 } NtcTsAnlyPcrPidEntry ::= SEQUENCE { ntcTsAnlyPcrPidPid Unsigned32, ntcTsAnlyPcrPidPcrIntervalTime Unsigned32, ntcTsAnlyPcrPidPcrRepeatError INTEGER, ntcTsAnlyPcrPidPcrAccuracyError INTEGER, ntcTsAnlyPcrPidMinJitter Integer32, ntcTsAnlyPcrPidMaxJitter Integer32, ntcTsAnlyPcrPidMinHoldJitter Integer32, ntcTsAnlyPcrPidMaxHoldJitter Integer32, ntcTsAnlyPcrPidRateOffset Unsigned32, ntcTsAnlyPcrPidPcrRate Unsigned32 } ntcTsAnlyPcrPidPid OBJECT-TYPE SYNTAX Unsigned32 (0..8190) MAX-ACCESS not-accessible STATUS current DESCRIPTION "PID" ::= { ntcTsAnlyPcrPidEntry 1 } ntcTsAnlyPcrPidPcrIntervalTime OBJECT-TYPE SYNTAX Unsigned32 (0..9999999) UNITS "ms" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured interval time (in milliseconds) between 2 PCR packets." ::= { ntcTsAnlyPcrPidEntry 2 } ntcTsAnlyPcrPidPcrRepeatError OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "PCR Repetition Error is raised when the spacing between two consecutive PCR values is more than 40ms. The condition can occur when PCR packets get lost or when PCR packets are not present at a sufficient rate." ::= { ntcTsAnlyPcrPidEntry 3 } ntcTsAnlyPcrPidPcrAccuracyError OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "The PCR Accuracy error is raised when the PCR accuracy exceeds +/- 500nsec. The definition of the alarm is taken from TR101290." ::= { ntcTsAnlyPcrPidEntry 4 } ntcTsAnlyPcrPidMinJitter OBJECT-TYPE SYNTAX Integer32 (-9999999..9999999) UNITS "ns" MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum value of PCR_AC (nanoseconds) over the last second." ::= { ntcTsAnlyPcrPidEntry 5 } ntcTsAnlyPcrPidMaxJitter OBJECT-TYPE SYNTAX Integer32 (-9999999..9999999) UNITS "ns" MAX-ACCESS read-only STATUS current DESCRIPTION "Max Jitter PCR_AC (nanoseconds) measured over the last second." ::= { ntcTsAnlyPcrPidEntry 6 } ntcTsAnlyPcrPidMinHoldJitter OBJECT-TYPE SYNTAX Integer32 (-9999999..9999999) UNITS "ns" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum measured PCR_AC value (in nanoseconds) computed since the last reset." ::= { ntcTsAnlyPcrPidEntry 7 } ntcTsAnlyPcrPidMaxHoldJitter OBJECT-TYPE SYNTAX Integer32 (-9999999..9999999) UNITS "ns" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum measured PCR_AC value (in nanoseconds) computed since the last reset." ::= { ntcTsAnlyPcrPidEntry 8 } ntcTsAnlyPcrPidRateOffset OBJECT-TYPE SYNTAX Unsigned32 UNITS "ppm" MAX-ACCESS read-only STATUS current DESCRIPTION "Rate Offset in PPM of the inband clock companed to the local clock. (ASI: local clock, TS over IP: configured bitrate)" ::= { ntcTsAnlyPcrPidEntry 9 } ntcTsAnlyPcrPidPcrRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "PCR Rate (Mb/s) calculated by using the inband PCR timing information." ::= { ntcTsAnlyPcrPidEntry 10 } ntcTsAnlyAlmSyncLoss OBJECT-TYPE SYNTAX NtcAlarmState MAX-ACCESS read-only STATUS current DESCRIPTION "Alarm indicating that the synchronization with the Transport-Stream (TS) has been lost. This conditions occurs when 2 or more consecutive corrupted SYNC bytes are received. This variable indicates the current status of the alarm." ::= { ntcTsAnlyAlarm 1 } ntcTsAnlyAlmSyncByte OBJECT-TYPE SYNTAX NtcAlarmState MAX-ACCESS read-only STATUS current DESCRIPTION "This alarm is raised when a single corrupted SYNC byte is detected and cleared when the next correct one appears. This variable indicates the current status of the alarm." ::= { ntcTsAnlyAlarm 2 } ntcTsAnlyAlmPat OBJECT-TYPE SYNTAX NtcAlarmState MAX-ACCESS read-only STATUS current DESCRIPTION "This alarm indicates that the 'Program Association Table' (PAT) can not be detected properly in the stream. The PAT table id (0x00) should be detected in a PID 0x0000 at least every 0.5 s. This variable indicates the current status of the alarm." ::= { ntcTsAnlyAlarm 3 } ntcTsAnlyAlmContinuityCount OBJECT-TYPE SYNTAX NtcAlarmState MAX-ACCESS read-only STATUS current DESCRIPTION "This alarm is raised when packets arrive out of sequence, get dropped or occur more than once. This variable indicates the current status of the alarm." ::= { ntcTsAnlyAlarm 4 } ntcTsAnlyAlmTransport OBJECT-TYPE SYNTAX NtcAlarmState MAX-ACCESS read-only STATUS current DESCRIPTION "This alarm condition is detected when the 'Transport Error indicator'-bit in the TS-Header is set to '1' for a specific PID. The alarm condition is cleared when no Transport Error indication is detected for 5 sec. This variable indicates the current status of the alarm." ::= { ntcTsAnlyAlarm 5 } ntcTsAnlyAlmPcrRepetition OBJECT-TYPE SYNTAX NtcAlarmState MAX-ACCESS read-only STATUS current DESCRIPTION "This alarm is raised if the spacing between two consecutive PCR values is more than 40ms. The condition can occur when PCR packets get lost or when PCR packets are not present at a sufficient rate. This variable indicates the current status of the alarm." ::= { ntcTsAnlyAlarm 6 } ntcTsAnlyAlmPcrDiscontinuity OBJECT-TYPE SYNTAX NtcAlarmState MAX-ACCESS read-only STATUS current DESCRIPTION "This alarm indicates that the difference between two consecutive PCR values exceeds the range [0-100] ms, while the 'discontinuity indicator' bit is not set. This bit in the Adaptation Field should trigger a reset of the PCR evaluation functionality. This variable indicates the current status of the alarm." ::= { ntcTsAnlyAlarm 7 } ntcTsAnlyAlmPcrAccuracy OBJECT-TYPE SYNTAX NtcAlarmState MAX-ACCESS read-only STATUS current DESCRIPTION "This alarm condition occurs when the PCR accuracy exceeds +/- 500nsec. The definition of the alarm is taken from TR101290. This variable indicates the current status of the alarm." ::= { ntcTsAnlyAlarm 8 } ntcTsAnlyEPidTable OBJECT-TYPE SYNTAX SEQUENCE OF NtcTsAnlyEPidEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table which contains PIDs on which an error has been detected." ::= { ntcTsAnlyObjects 7 } ntcTsAnlyEPidEntry OBJECT-TYPE SYNTAX NtcTsAnlyEPidEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row of the ntcTsAnlyEPidTable." INDEX { ntcTsAnlyEPidPid } ::= { ntcTsAnlyEPidTable 1 } NtcTsAnlyEPidEntry ::= SEQUENCE { ntcTsAnlyEPidPid Unsigned32, ntcTsAnlyEPidType INTEGER, ntcTsAnlyEPidCtuCntErrorCntr Counter64, ntcTsAnlyEPidContinuityError INTEGER, ntcTsAnlyEPidTransportError INTEGER } ntcTsAnlyEPidPid OBJECT-TYPE SYNTAX Unsigned32 (0..8190) MAX-ACCESS not-accessible STATUS current DESCRIPTION "PID" ::= { ntcTsAnlyEPidEntry 1 } ntcTsAnlyEPidType OBJECT-TYPE SYNTAX INTEGER { others(0), video(1), audio(2), privateSection(3), pesPrivate(4), mheg(5), dsmCc(6), h2221(7), mpe(8), auxiliary(9), slOrFlexMux(10), sdp(11), metadata(12), ipmp(13), userPrivate(14), pat(15), cat(16), tsdt(17), nitOrSt(18), sdtOrBatOrSt(19), eitOrStCit(20), rstOrSt(21), tdtOrTotOrSt(22), netwSync(23), rnt(24), inband(25), measurement(26), dit(27), sit(28), null(29), othersOrGhost(30), pmt(31), visual(32), srm(33), ecm(34), emm(35) } MAX-ACCESS read-only STATUS current DESCRIPTION "PID Type" ::= { ntcTsAnlyEPidEntry 2 } ntcTsAnlyEPidCtuCntErrorCntr OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of packets with a continuity count error." ::= { ntcTsAnlyEPidEntry 3 } ntcTsAnlyEPidContinuityError OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Continuity Count Error" ::= { ntcTsAnlyEPidEntry 4 } ntcTsAnlyEPidTransportError OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Transport Error" ::= { ntcTsAnlyEPidEntry 5 } -- -- Module Conformance -- ntcTsAnlyConfGrpV1Standard OBJECT-GROUP OBJECTS { ntcTsAnlyEble, ntcTsAnlyReset, ntcTsAnlyEstimatedTsRate, ntcTsAnlyPidType, ntcTsAnlyPidPIDRate, ntcTsAnlyPidContinuityError, ntcTsAnlyPidTransportError, ntcTsAnlyPidCtuCntErrorCntr, ntcTsAnlyPcrPidPcrIntervalTime, ntcTsAnlyPcrPidPcrRepeatError, ntcTsAnlyPcrPidPcrAccuracyError, ntcTsAnlyPcrPidMinJitter, ntcTsAnlyPcrPidMaxJitter, ntcTsAnlyPcrPidMinHoldJitter, ntcTsAnlyPcrPidMaxHoldJitter, ntcTsAnlyPcrPidRateOffset, ntcTsAnlyPcrPidPcrRate, ntcTsAnlyAlmSyncLoss, ntcTsAnlyAlmSyncByte, ntcTsAnlyAlmPat, ntcTsAnlyAlmContinuityCount, ntcTsAnlyAlmTransport, ntcTsAnlyAlmPcrRepetition, ntcTsAnlyAlmPcrDiscontinuity, ntcTsAnlyAlmPcrAccuracy, ntcTsAnlyEPidType, ntcTsAnlyEPidCtuCntErrorCntr, ntcTsAnlyEPidContinuityError, ntcTsAnlyEPidTransportError } STATUS current DESCRIPTION "Managed objects that constitute version 1 of a system device with standard capabilities." ::= { ntcTsAnlyConfGroup 1} ntcTsAnlyConfCompV1Standard MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance statement for Newtec device MIB implementations." MODULE -- this module MANDATORY-GROUPS { ntcTsAnlyConfGrpV1Standard } ::= { ntcTsAnlyConfCompliance 1 } END