NETI-EVT-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Unsigned32, enterprises FROM SNMPv2-SMI DisplayString, DateAndTime, TEXTUAL-CONVENTION, RowPointer, TruthValue FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF; nevtMIB MODULE-IDENTITY LAST-UPDATED "201503031600Z" ORGANIZATION "Net Insight AB" CONTACT-INFO "Net Insight AB Box 42093 SE-126 14 Stockholm Sweden Tel +46-8-685 0400 info@netinsight.se" DESCRIPTION "MIB containing event and alarm information. The MIB contains tables for events and alarms, and defined notifications for events and alarms. nevtEventTable. Table with the last number of events. The event table contains the events that are sent as SNMP notifications. These events indicate change of alarms, or change in other tables defined in other MIBs, that uses the mechanism in this MIB to notify a table change. If a notification receiver misses notifications, it can retrieve the lost notifications from this table. nevtAlarmTable. Table with all active alarms, and the last historic alarms. The alarm table holds all active alarms, and possibly also a number of the last cleared alarms. nevtActiveAlarmTable. Table will all active (non-clear) alarms. The active alarm table holds only the active alarms." REVISION "201503031600Z" DESCRIPTION "Added objects for holding purpose text of managed object; nevtEventPurpose, nevtAlarmPurose and nevtActiveAlarmPurpose. The objects are added to nevtEventTable, nevtAlarmTable and the nevtActiveAlarmTable and to all event and alarm notification. The nevtTrapPurpose has been marked as obsoleted. Corrected spelling on descriptions. Removed the Conformance group. Removed dependency and import from NETI-COMMON-MIB." REVISION "201306031100Z" DESCRIPTION "This MIB replaces the NETI-EVENT-MIB. This MIB has the same objects as the NETI-EVENT-MIB, revision 201105031000Z, but this MIB registers new descriptor for each of the objects. This violates RFC2578, ch 3.6, item 1, where it is stated that only one descriptor can be registered to an object. However, item 2 states that it is allowed to assign additional descriptors to an object, from which it follows that any object can be referred to by different descriptors. The NETI-EVENT-MIB contains registered descriptors that are in conflict with descriptors in other standard MIBs. This conflict can cause problems in network management systems that rely on that a descriptor uniquely identifies a single object. The least costly solution to this problem this was determined to be to simply register new descriptors for all objects. All the objects in this MIB are binary compatible with the descriptions in NETI-EVENT-MIB, meaning that any network management system may choose to continue to use the NETI-EVENT-MIB, or to use this NETI-EVT-MIB." ::= { netiGeneric 1 } -- ------------------------------------------------------------- -- Objects in the NETI-EVT-MIB -- ------------------------------------------------------------- netinsight OBJECT IDENTIFIER ::= { enterprises 2928 } netiGeneric OBJECT IDENTIFIER ::= { netinsight 2 } nevtObjects OBJECT IDENTIFIER ::= { nevtMIB 1 } nevtNotifications OBJECT IDENTIFIER ::= { nevtMIB 2 } nevtConformanceGroups OBJECT IDENTIFIER ::= { nevtMIB 3 } -- ------------------------------------------------------------- -- Textual Conventions -- ------------------------------------------------------------- NevtEventType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The type of event. 'created', 'modified' and 'deleted' indicates status of a conceptual row in a table. If the event represents an alarm, the type is 'none'." SYNTAX INTEGER { none(0), created(1), modified(2), deleted(3) } NevtAlarmType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The alarm type as specified in CCITT Rec. X.733(1992 E)|ISO/EIC 10164-4:1992 (E). Alarm type 'unknown' may be set if the alarm type can not be determined, or when an event is not caused by an alarm." SYNTAX INTEGER { unknown(0), communication(1), qualityOfService(2), processingError(3), equipment(4), environmental(5) } NevtAlarmSeverity ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The alarm severity as specified in CCITT Rec. X.733(1992 E)|ISO/EIC 10164-4:1992 (E). Alarm severity 'unknown' may be set if the alarm type can not be determined, or when the event is not caused by an alarm." SYNTAX INTEGER { unknown(0), indeterminate(1), critical(2), major(3), minor(4), warning(5), cleared(6) } NevtAlarmCause ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The alarm cause 1-57 as specified in CCITT Rec. X.733(1992 E)|ISO/EIC 10164-4:1992 (E). Alarm cause 'unknown' may be set if the cause can not be determined, or if the event was not caused by an alarm. (0 and 58 and above are proprietary)." SYNTAX INTEGER { unknown(0), adapterError(1), applicationSubsystemFailure(2), bandwidthReduced(3), callEstablishmentError(4), communicationsProtocolError(5), communicationsSubsystemFailure(6), configurationOrCustomizationError(7), congestion(8), corruptData(9), cpuCyclesLimitExceeded(10), datasetOrModemError(11), degradedSignal(12), dTEDCEInterfaceError(13), enclosureDoorOpen(14), equipmentMalfunction(15), excessiveVibration(16), fileError(17), fireDetected(18), floodDetected(19), framingError(20), heatingOrVentilationOrCoolingSystemProblem(21), humidityUnacceptable(22), inputOutputDeviceError(23), inputDeviceError(24), lANError(25), leakDetected(26), localNodeTransmissionError(27), lossOfFrame(28), lossOfSignal(29), materialSupplyExhausted(30), multiplexerProblem(31), outOfMemory(32), outputDeviceError(33), performanceDegraded(34), powerProblem(35), pressureUnacceptable(36), processorProblem(37), pumpFailure(38), queueSizeExceeded(39), receiveFailure(40), receiverFailure(41), remoteNodeTransmissionError(42), resourceAtOrNearingCapacity(43), responseTimeExcessive(44), retransmissionRateExcessive(45), softwareError(46), softwareProgramAbnormallyTerminated(47), softwareProgramError(48), storageCapacityProblem(49), temperatureUnacceptable(50), thresholdCrossed(51), timingProblem(52), toxicLeakDetected(53), transmitFailure(54), transmitterFailure(55), underlyingResourceUnavailable(56), versionMismatch(57), phyLossOfSignal(58), -- use lossOfSignal instead phyLossOfFrame(59), -- use lossOfFrame instead phyAlarmIndicationSignal(60), -- use alarmIndicationSignal phyRemoteDefectIndication(61), -- use remoteDefectIndication instead phySignalFailure(62), -- currently not not used phySignalDegraded(63), -- use degradedSignal instead testmodeEntered(64), serviceUnavailable(65), alarmIndicationSignal(66), remoteDefectIndication(67), replaceableUnitMissing(68), -- 62 in rfc3877 replaceableUnitProblem(69) -- from rfc3877 } -- ------------------------------------------------------------- -- The Event objects -- ------------------------------------------------------------- -- Some scalars to examine status of the event log. nevtSequenceCounter OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the latest sent event defined as notifications in this mib. By examine his object, the notification receiver can determine whether it has missed any notifications. The counter resets to zero at cold start, indicating that no events has been sent, and that the event table is empty. The counter will wrap and restart at value `1' when it passes its maximum value" ::= { nevtObjects 1 } nevtLastChangedTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The time when an event was last changed, and a notification was sent." ::= { nevtObjects 2 } -- The event table group contains a set of objects for -- getting the event list in the node. The event table -- contains all notifications that has been sent from the -- node using this mechanism. Events could either be -- alarms or notifications on changes in configuration -- tables. nevtEventTable OBJECT-TYPE SYNTAX SEQUENCE OF NevtEventEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing the most recent events. The maximum size of the table depends on the implementation" ::= { nevtObjects 3 } nevtEventEntry OBJECT-TYPE SYNTAX NevtEventEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "One entry in the table holds one event. Events are either created by the agent when a conceptual row has been changed in a table defined in another mib, or when an alarm status is changed in the alarm table defined in this mib." INDEX { nevtEventIndex } ::= { nevtEventTable 1 } NevtEventEntry ::= SEQUENCE { nevtEventIndex Unsigned32, nevtEventObject RowPointer, nevtEventObjectName DisplayString, nevtEventAlarmType NevtAlarmType, nevtEventType NevtEventType, nevtEventCause NevtAlarmCause, nevtEventSeverity NevtAlarmSeverity, nevtEventText DisplayString, nevtEventCreatedTime DateAndTime, nevtEventPurpose SnmpAdminString } nevtEventIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Arbitrary index for an entry in the event table. The eventIndex follows the nevtSequenceCounter as such that the nevtSequenceCounter refers to the last event in the table" ::= { nevtEventEntry 1 } nevtEventObject OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "A pointer to the conceptual row of the object that caused this event. If the object is unavailable, the value is { 0 0 }." ::= { nevtEventEntry 2 } nevtEventObjectName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "A text describing the object that caused the event in a for humans more readable form. If not set then this object contains a zero-length string." ::= { nevtEventEntry 3 } nevtEventAlarmType OBJECT-TYPE SYNTAX NevtAlarmType MAX-ACCESS read-only STATUS current DESCRIPTION "This is the event type as specified in NevtAlarmType." ::= { nevtEventEntry 4 } nevtEventType OBJECT-TYPE SYNTAX NevtEventType MAX-ACCESS read-only STATUS current DESCRIPTION "This is the event type as specified in NevtEventType." ::= { nevtEventEntry 5 } nevtEventCause OBJECT-TYPE SYNTAX NevtAlarmCause MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm cause as specified in NevtAlarmCause." ::= { nevtEventEntry 6 } nevtEventSeverity OBJECT-TYPE SYNTAX NevtAlarmSeverity MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm severity as specified in NevtAlarmSeverity." ::= { nevtEventEntry 7 } nevtEventText OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "A text describing the event in a for humans more readable form." ::= { nevtEventEntry 8 } nevtEventCreatedTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The time when the event was created." ::= { nevtEventEntry 9 } nevtEventPurpose OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The purpose text inherited from the object to which the event belongs. The purpose is usually a user-supplied text describing the object. The purpose is assigned on the object. If an object does not have a purpose, then this is the empty string." ::= { nevtEventEntry 10 } -- The Alarm table contains all active and some cleared alarms -- in the node. nevtAlarmTable OBJECT-TYPE SYNTAX SEQUENCE OF NevtAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing alarms and their status. The maximum size of the table depends on the implementation." ::= { nevtObjects 4 } nevtAlarmEntry OBJECT-TYPE SYNTAX NevtAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "One entry in the table holds one alarm. The table contains all active alarms, and depending on the implementation, it may contian none, some or several cleared alarms." INDEX { nevtAlarmIndex } ::= { nevtAlarmTable 1 } NevtAlarmEntry ::= SEQUENCE { nevtAlarmIndex Unsigned32, nevtAlarmObject RowPointer, nevtAlarmObjectName DisplayString, nevtAlarmAlarmType NevtAlarmType, nevtAlarmCause NevtAlarmCause, nevtAlarmSeverity NevtAlarmSeverity, nevtAlarmText DisplayString, nevtAlarmLastChangedTime DateAndTime, nevtAlarmAcknowledged TruthValue, nevtAlarmCreatedTime DateAndTime, nevtAlarmPurpose SnmpAdminString } nevtAlarmIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Arbitrary index for an entry in the alarm table." ::= { nevtAlarmEntry 1 } nevtAlarmObject OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "A pointer to the conceptual row of the object that caused this alarm. If the object is unavailable, the value is { 0 0 }." ::= { nevtAlarmEntry 2 } nevtAlarmObjectName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "A text describing the object in a more readable form. If not set then this object contains a zero-length string." ::= { nevtAlarmEntry 3 } nevtAlarmAlarmType OBJECT-TYPE SYNTAX NevtAlarmType MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm type as specified in NevtAlarmType." ::= { nevtAlarmEntry 4 } nevtAlarmCause OBJECT-TYPE SYNTAX NevtAlarmCause MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm cause as specified in NevtAlarmCause." ::= { nevtAlarmEntry 5 } nevtAlarmSeverity OBJECT-TYPE SYNTAX NevtAlarmSeverity MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm severity as specified in NevtAlarmSeverity." ::= { nevtAlarmEntry 6 } nevtAlarmText OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "A text describing the alarm in a more readable form." ::= { nevtAlarmEntry 7 } nevtAlarmLastChangedTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The time when the alarm was changed, i.e. when the alarm was created, or nevtAlarmSeverity or nevtAlarmAcknowledged was changed." ::= { nevtAlarmEntry 8 } nevtAlarmAcknowledged OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The acknowledgement status of the alarm. This is set to `true' to indicate that the alarm is is acknowledged, and set to `false' to clear the acknowledge." ::= { nevtAlarmEntry 9 } nevtAlarmCreatedTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The time when the alarm was created." ::= { nevtAlarmEntry 10 } nevtAlarmPurpose OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The purpose text inherited from the object to which the alarm belongs. The purpose is usually a user-supplied text describing the object. The purpose is assigned on the object. If an object does not have a purpose, then this is the empty string." ::= { nevtAlarmEntry 11 } -- The Alarm table contains all active alarms in the node. nevtActiveAlarmTable OBJECT-TYPE SYNTAX SEQUENCE OF EventActiveAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing alarms and their status. The maximum size of the table depends on the implementation." ::= { nevtObjects 6 } nevtActiveAlarmEntry OBJECT-TYPE SYNTAX EventActiveAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "One entry in the table holds one alarm. The table contains only active alarms." INDEX { nevtActiveAlarmIndex } ::= { nevtActiveAlarmTable 1 } EventActiveAlarmEntry ::= SEQUENCE { nevtActiveAlarmIndex Unsigned32, nevtActiveAlarmObject RowPointer, nevtActiveAlarmObjectName DisplayString, nevtActiveAlarmAlarmType NevtAlarmType, nevtActiveAlarmCause NevtAlarmCause, nevtActiveAlarmSeverity NevtAlarmSeverity, nevtActiveAlarmText DisplayString, nevtActiveAlarmLastChangedTime DateAndTime, nevtActiveAlarmAcknowledged TruthValue, nevtActiveAlarmCreatedTime DateAndTime, nevtActiveAlarmPurpose SnmpAdminString } nevtActiveAlarmIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Arbitrary index for an entry in the alarm table." ::= { nevtActiveAlarmEntry 1 } nevtActiveAlarmObject OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "A pointer to the conceptual row of the object that caused this alarm. If the object is unavailable, the value is { 0 0 }." ::= { nevtActiveAlarmEntry 2 } nevtActiveAlarmObjectName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "A text describing the object in a more readable form. If not set then this object contains a zero-length string." ::= { nevtActiveAlarmEntry 3 } nevtActiveAlarmAlarmType OBJECT-TYPE SYNTAX NevtAlarmType MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm type as specified in NevtAlarmType." ::= { nevtActiveAlarmEntry 4 } nevtActiveAlarmCause OBJECT-TYPE SYNTAX NevtAlarmCause MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm cause as specified in NevtAlarmCause." ::= { nevtActiveAlarmEntry 5 } nevtActiveAlarmSeverity OBJECT-TYPE SYNTAX NevtAlarmSeverity MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm severity as specified in NevtAlarmSeverity." ::= { nevtActiveAlarmEntry 6 } nevtActiveAlarmText OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "A text describing the alarm in a more readable form." ::= { nevtActiveAlarmEntry 7 } nevtActiveAlarmLastChangedTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The time when the alarm was changed, i.e. when the alarm was created, or nevtActiveAlarmSeverity or nevtActiveAlarmAcknowledged was changed." ::= { nevtActiveAlarmEntry 8 } nevtActiveAlarmAcknowledged OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The acknowledgement status of the alarm. This is set to 'true' to indicate that the alarm is is acknowledged, and set to 'false' to clear the acknowledge." ::= { nevtActiveAlarmEntry 9 } nevtActiveAlarmCreatedTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The time when the alarm was created." ::= { nevtActiveAlarmEntry 10 } nevtActiveAlarmPurpose OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The purpose text inherited from the object to which the alarm belongs. The purpose is usually a user-supplied text describing the object. The purpose is assigned on the object. If an object does not have a purpose, then this is the empty string." ::= { nevtActiveAlarmEntry 11 } -- ------------------------------------------------------------- -- Group with alarm counters -- ------------------------------------------------------------- -- The group contains counters per alarm severity. The counters -- holds the number of active alarms per severity. nevtAlarmCountersGroup OBJECT IDENTIFIER ::= { nevtObjects 5 } nevtCriticalCounter OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of active alarms with the severity 'critical'." ::= { nevtAlarmCountersGroup 1 } nevtMajorCounter OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of active alarms with the severity 'major'." ::= { nevtAlarmCountersGroup 2 } nevtMinorCounter OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of active alarms with the severity 'minor'." ::= { nevtAlarmCountersGroup 3 } nevtWarningCounter OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of active alarms with the severity 'warning'." ::= { nevtAlarmCountersGroup 4 } nevtIndeterminateCounter OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of active alarms with the severity 'indeterminate'." ::= { nevtAlarmCountersGroup 5 } -- ------------------------------------------------------------- -- Alarm related notifications -- ------------------------------------------------------------- nevtNotificationObjectsGroup OBJECT IDENTIFIER ::= { nevtObjects 7 } nevtTrapPurpose OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS obsolete DESCRIPTION "Indicates the purpose of a managed object to where a trap belongs. This OID may be appended to traps in the nevtNotifications group at the discretion of the SNMP agent." ::= { nevtNotificationObjectsGroup 1 } -- Notifications are sent when the state of an alarm is -- changed. Each severity has its own trap since many -- SNMP managers organize severity of events based on the -- trap identity. -- The management application should use alarmObjectName -- and alarmCause (or alarmObject if given) it it wishes -- to keep track of a certain fault state. -- The standard traps (cold start etc.) should be used -- to trigger re-reading the alarm list if the node crashes -- or the alarm list is reset for some reason. nevtAlarmCritical NOTIFICATION-TYPE OBJECTS { nevtEventIndex, nevtEventObject, nevtEventObjectName, nevtEventAlarmType, nevtEventCause, nevtEventSeverity, nevtEventText, nevtEventCreatedTime, nevtSequenceCounter, nevtEventPurpose } STATUS current DESCRIPTION "Notification for an alarm with severity 'critical'." ::= { nevtNotifications 1 } nevtAlarmMajor NOTIFICATION-TYPE OBJECTS { nevtEventIndex, nevtEventObject, nevtEventObjectName, nevtEventAlarmType, nevtEventCause, nevtEventSeverity, nevtEventText, nevtEventCreatedTime, nevtSequenceCounter, nevtEventPurpose } STATUS current DESCRIPTION "Notification for an alarm with severity 'major'." ::= { nevtNotifications 2 } nevtAlarmMinor NOTIFICATION-TYPE OBJECTS { nevtEventIndex, nevtEventObject, nevtEventObjectName, nevtEventAlarmType, nevtEventCause, nevtEventSeverity, nevtEventText, nevtEventCreatedTime, nevtSequenceCounter, nevtEventPurpose } STATUS current DESCRIPTION "Notification for an alarm with severity 'minor'." ::= { nevtNotifications 3 } nevtAlarmWarning NOTIFICATION-TYPE OBJECTS { nevtEventIndex, nevtEventObject, nevtEventObjectName, nevtEventAlarmType, nevtEventCause, nevtEventSeverity, nevtEventText, nevtEventCreatedTime, nevtSequenceCounter, nevtEventPurpose } STATUS current DESCRIPTION "Notification for an alarm with severity 'warning'." ::= { nevtNotifications 4 } nevtAlarmIndeterminate NOTIFICATION-TYPE OBJECTS { nevtEventIndex, nevtEventObject, nevtEventObjectName, nevtEventAlarmType, nevtEventCause, nevtEventSeverity, nevtEventText, nevtEventCreatedTime, nevtSequenceCounter, nevtEventPurpose } STATUS current DESCRIPTION "Notification for an alarm with severity 'indeterminate'." ::= { nevtNotifications 5 } nevtAlarmUnknown NOTIFICATION-TYPE OBJECTS { nevtEventIndex, nevtEventObject, nevtEventObjectName, nevtEventAlarmType, nevtEventCause, nevtEventSeverity, nevtEventText, nevtEventCreatedTime, nevtSequenceCounter, nevtEventPurpose } STATUS current DESCRIPTION "Notification for an alarm with unknown severity." ::= { nevtNotifications 6 } nevtAlarmClear NOTIFICATION-TYPE OBJECTS { nevtEventIndex, nevtEventObject, nevtEventObjectName, nevtEventAlarmType, nevtEventCause, nevtEventSeverity, nevtEventText, nevtEventCreatedTime, nevtSequenceCounter, nevtEventPurpose } STATUS current DESCRIPTION "Notification for a cleared alarm." ::= { nevtNotifications 7 } -- Notifications are sent when a configuration change has occurred -- in the node. The type of configuration can be 'create', 'modify' -- or 'delete', i.e. a conceptual row is created, modified or -- deleted in the a table referred to by 'nevtObject'. nevtGenericEvent NOTIFICATION-TYPE OBJECTS { nevtEventObject, nevtEventObjectName, nevtEventType, nevtEventText, nevtEventCreatedTime, nevtSequenceCounter, nevtEventPurpose } STATUS current DESCRIPTION "Notification for a generic event." ::= { nevtNotifications 8 } END