DC-VPWS-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, enterprises, Unsigned32, Gauge32 FROM SNMPv2-SMI TruthValue, RowStatus FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB InetAddressType, InetAddress FROM INET-ADDRESS-MIB InterfaceIndex, InterfaceIndexOrZero, ifIndex FROM IF-MIB L2vpnPwBindType, L2vpnADType, L2vpnSigType, L2vpnVeIdOrZero, BgpRouteDistinguisher, BgpExtendedCommunity, l2vmEntityIndex FROM DC-L2VPN-MIB MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF IANAPwTypeTC FROM IANA-PWE3-MIB -- RFC5601 AdminStatus, NpgOperStatus, NumericIndex, NumericIndexOrZero FROM DC-MASTER-TC; vpwsMib MODULE-IDENTITY LAST-UPDATED "201503080000Z" -- March 8, 2015 ORGANIZATION "MRV Communications." CONTACT-INFO "For technical support, please contact your service channel" DESCRIPTION "VPWS MIB." ::= { opx 19 } nbase OBJECT IDENTIFIER ::= { enterprises 629 } opx OBJECT IDENTIFIER ::= { nbase 10 } vpwsObjects OBJECT IDENTIFIER ::= { vpwsMib 1 } -- VPWS tables vpwsConformance OBJECT IDENTIFIER ::= { vpwsMib 2 } -- Module conformance ------------------------------------------------------------------------------- -- -- VPWS Config Table. -- vpwsConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF VpwsConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "VPWS Configuration Table. This table specifies information for configuring and monitoring Virtual Private Wire Services (VPWS). Note that any changes made to this table when vpwsStatusOperStatus is 'up' may cause the VPWS to be deactivated (vpwsStatusOperStatus 'down') before the change is made. The VPWS will then attempt to re-activate. The VPWS may or may not re-activate depending on the validity of the new configuration." ::= { vpwsObjects 1 } vpwsConfigEntry OBJECT-TYPE SYNTAX VpwsConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents a configured VPWS." INDEX { l2vmEntityIndex, vpwsIndex } ::= { vpwsConfigTable 1 } VpwsConfigEntry ::= SEQUENCE { vpwsIndex NumericIndex, vpwsConfigRowStatus RowStatus, vpwsConfigAdminStatus AdminStatus, vpwsConfigOperStatus NpgOperStatus, vpwsConfigName SnmpAdminString, vpwsConfigDescr SnmpAdminString, vpwsConfigADType L2vpnADType, vpwsConfigSigType L2vpnSigType, vpwsConfigPwEncapType IANAPwTypeTC, vpwsConfigMtu Unsigned32, vpwsConfigControlWord TruthValue, vpwsConfigSeqDelivery TruthValue, vpwsConfigRouteDistinguisher BgpRouteDistinguisher, vpwsConfigVpnId BgpExtendedCommunity, vpwsConfigLocalSiteID L2vpnVeIdOrZero, vpwsConfigLocalPreference Unsigned32, vpwsConfigLabelBlockSize Unsigned32, vpwsConfigIncludeCSV TruthValue, vpwsConfigIgnoreMtuMismatch TruthValue, vpwsConfigIgnoreEncapsMismatch TruthValue } vpwsIndex OBJECT-TYPE SYNTAX NumericIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index identifying the VPWS instance." ::= { vpwsConfigEntry 2 } vpwsConfigRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status for this VPWS Configuration Table entry, used to create and destroy table entries." ::= { vpwsConfigEntry 3 } vpwsConfigAdminStatus OBJECT-TYPE SYNTAX AdminStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The administrative status of this VPWS instance, used to activate and deactivate the VPWS instance." DEFVAL { adminStatusUp } ::= { vpwsConfigEntry 4 } vpwsConfigOperStatus OBJECT-TYPE SYNTAX NpgOperStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational state of this VPWS instance. If the operational status is 'up' then the VPWS is programmed in the data plane." ::= { vpwsConfigEntry 5 } vpwsConfigName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "A textual name of the VPWS instance. If there is no local name, or this field is otherwise not applicable, then this field MUST contain a zero-length octet string." ::= { vpwsConfigEntry 6 } vpwsConfigDescr OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "A textual string containing information about the VPWS instance. If there is no information for this VPWS instance, then this field MUST contain a zero-length octet string." ::= { vpwsConfigEntry 7 } vpwsConfigADType OBJECT-TYPE SYNTAX L2vpnADType MAX-ACCESS read-create STATUS current DESCRIPTION "The auto-discovery protocol used by this VPWS. Changing this value will cause an interruption to data flow for this VPWS." DEFVAL { none } ::= { vpwsConfigEntry 8 } vpwsConfigSigType OBJECT-TYPE SYNTAX L2vpnSigType MAX-ACCESS read-create STATUS current DESCRIPTION "The pseudowire signaling protocol used for auto-created PWs on this VPWS. If vpwsConfigADType is set to 'none' this field is ignored. If vpwsConfigADType is set to 'bgp' this field must be set to 'ldp' or 'bgp'. Changing this value will cause an interruption to data flow for this VPWS." DEFVAL { none } ::= { vpwsConfigEntry 9 } vpwsConfigPwEncapType OBJECT-TYPE SYNTAX IANAPwTypeTC MAX-ACCESS read-create STATUS current DESCRIPTION "The MPLS pseudowire encapsulation type used by this VPWS. Changing this value will cause an interruption to data flow for this VPWS." DEFVAL { ethernet } ::= { vpwsConfigEntry 10 } vpwsConfigMtu OBJECT-TYPE SYNTAX Unsigned32 (64..9192) MAX-ACCESS read-create STATUS current DESCRIPTION "The layer 2 MTU of this VPWS. When using auto-discovery and signaling, this specifies the signaled layer 2 MTU. Changing this value will cause an interruption to data flow for this VPWS." DEFVAL { 1500 } ::= { vpwsConfigEntry 11 } vpwsConfigControlWord OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Whether or not the pseudowires use a PW control word. Changing this value will cause an interruption to data flow for this VPWS." DEFVAL { false } ::= { vpwsConfigEntry 12 } vpwsConfigSeqDelivery OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Whether or not the pseudowires must provide sequenced delivery of traffic. Changing this value will cause an interruption to data flow for this VPWS." DEFVAL { false } ::= { vpwsConfigEntry 13 } vpwsConfigRouteDistinguisher OBJECT-TYPE SYNTAX BgpRouteDistinguisher MAX-ACCESS read-create STATUS current DESCRIPTION "The route distinguisher for this VPWS. See [RFC4364] for a complete definition of a route distinguisher. This is only used if BGP auto-discovery is enabled (vpwsConfigADType = bgp). Changing this value will cause an interruption to data flow for this VPWS." DEFVAL { '0000000000000000'H } ::= { vpwsConfigEntry 14 } vpwsConfigVpnId OBJECT-TYPE SYNTAX BgpExtendedCommunity MAX-ACCESS read-create STATUS current DESCRIPTION "The VPN ID to advertise as a BGP extended community, or zero if none. If the VPWS uses BGP auto-discovery and LDP signaling (vpwsConfigADType = bgp and vpwsConfigSigType = ldp) then this must be set to a valid VPN ID, otherwise it is unused and can be set to zero. If the VPWS uses BGP auto-discovery and LDP signaling then the VPN ID is used as follows. - The VPWS advertises the VPN ID as a BGP extended community attribute on all BGP L2VPN routes that it exports. - The VPWS uses the VPN ID as an import filter on all BGP L2VPN routes that it imports (in addition to Route Target import filtering). - The VPWS uses the VPN ID as the AGI value in LDP messages. Changing this value will cause an interruption to data flow for this VPWS." DEFVAL { '0000000000000000'H } ::= { vpwsConfigEntry 15 } vpwsConfigLocalSiteID OBJECT-TYPE SYNTAX L2vpnVeIdOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "The local VPWS site ID, or zero if not specified. This is only used if BGP auto-discovery is enabled (vpwsConfigADType = bgp). It can be used with BGP or LDP signaling. If auto-discovery is enabled then the VPWS service establishes a pseudowire (PW) between each pair of VPWS sites within a VPWS. The valid range for VPWS site IDs depends on whether LDP or BGP signaling is used. - For LDP signaling (vpwsConfigSigType = ldp) the valid range is 1-4294967295 (4 bytes). - For BGP signaling (vpwsConfigSigType = bgp) the valid range is 1-65535 (2 bytes). The use of the VPWS site ID in auto-discovery and signaling also depends on whether LDP or BGP signaling is used. - For BGP auto-discovery with LDP signaling the VPWS site ID is advertised in the 4-byte 'PE_addr' field in the BGP NLRI specified in [RFC 6074]. It is also used as the local SAII/TAII value in LDP messages. - For BGP auto-discovery with BGP signaling the VPWS site ID is advertised in the 2-byte 'VE ID' field in the BGP NLRI specified in [RFC 4761]. Changing this value will cause an interruption to data flow for this VPWS." DEFVAL { 0 } ::= { vpwsConfigEntry 16 } vpwsConfigLocalPreference OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The preference that the local PE router is the designated forwarder for this VPWS. High values are preferred to low values. This is only used if BGP auto-discovery is enabled (vpwsConfigADType = bgp). It can be used with BGP or LDP signaling. The local PE router sets the LOCAL_PREF attribute to the value configured in this field in the BGP routes that it sends for this VPWS. Changing this value will cause an interruption to data flow for this VPWS." DEFVAL { 100 } ::= { vpwsConfigEntry 17 } vpwsConfigLabelBlockSize OBJECT-TYPE SYNTAX Unsigned32 (2 | 4 | 8 | 16) MAX-ACCESS read-create STATUS current DESCRIPTION "The size of the label blocks for this VPWS. This is only used when using BGP auto-discovery with BGP signaling (vpwsConfigADType = bgp and vpwsConfigSigType = bgp). The only currently-permitted sizes are 2, 4, 8 and 16. Changing this value will cause an interruption to data flow for this VPWS." DEFVAL { 8 } ::= { vpwsConfigEntry 18 } vpwsConfigIncludeCSV OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Whether or not the BGP NLRI for this VPWS will include a Circuit Status Vector TLV. This is only used when using BGP auto-discovery with BGP signaling (vpwsConfigADType = bgp and vpwsConfigSigType = bgp). Changing this value will cause an interruption to data flow for this VPWS." DEFVAL { false } ::= { vpwsConfigEntry 19 } vpwsConfigIgnoreMtuMismatch OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This field specifies whether mismatches of MTU size with remote PE routers should be ignored for this VPWS. If this field is false, PWs will not be established to remote PE routers that signal a different MTU. Otherwise PWs will be established. Changing this value will cause an interruption to data flow for this VPWS." DEFVAL { false } ::= { vpwsConfigEntry 20 } vpwsConfigIgnoreEncapsMismatch OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This field specifies whether mismatches of encapsulation type with remote PE routers should be ignored for this VPWS. If this field is false, PWs will not be established to remote PE routers that signal a different encapsulation type. Otherwise PWs will be established. Changing this value will cause an interruption to data flow for this VPWS." DEFVAL { false } ::= { vpwsConfigEntry 21 } -- End of VPWS Config Table. ------------------------------------------------------------------------------- -- -- VPWS Status Table (READ-ONLY). -- vpwsStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF VpwsStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "VPWS Status Table (read-only). This table reports the status of Virtual Private Wire Services (VPWS)." ::= { vpwsObjects 2 } vpwsStatusEntry OBJECT-TYPE SYNTAX VpwsStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents a VPWS." INDEX { l2vmEntityIndex, vpwsIndex } ::= { vpwsStatusTable 1 } VpwsStatusEntry ::= SEQUENCE { vpwsStatusOperStatus NpgOperStatus, vpwsStatusVcCount Gauge32, vpwsStatusDesignatedForwarder TruthValue } vpwsStatusOperStatus OBJECT-TYPE SYNTAX NpgOperStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational state of this VPWS instance. If the operational status is 'up' then the VPWS has been successfully activated." ::= { vpwsStatusEntry 3 } vpwsStatusVcCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Virtual Circuits currently present in this VPWS instance. Specifically, this is number of local Attachment Circuits (ACs) bound to active pseudowires in this VPWS instance." ::= { vpwsStatusEntry 4 } vpwsStatusDesignatedForwarder OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Whether or not the PE router is currently the elected Designated Forwarder for this VPWS instance. This field is only used if BGP auto-discovery is enabled (vpwsConfigADType = bgp). Otherwise, it is set to false." ::= { vpwsStatusEntry 5 } -- End of VPWS Status Table. ------------------------------------------------------------------------------- -- -- VPWS Binding Config Table. -- vpwsBindCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF VpwsBindCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "VPWS Binding Config Table. This table configures bindings of Attachment Circuits (ACs) to VPWS instances, pseudowires (PWs), and layer 2 local switching rules (hairpins). Multiple ACs can be associated with a single VPWS. If the binding corresponds to two VPWS sites that are hosted by a single PE router, a hairpin can be created between the two sites' ACs. Otherwise, a PW set is used to establish connectivity. The method for associating ACs with PWs depends on whether auto-discovery is enabled. - If auto-discovery is disabled (vpwsConfigADType = none) then PWs are provisioned in the pwTable. In this case, each AC is bound to a set of provisioned PWs, that are identified by a PW Set Index. PW redundancy configuration is not yet supported by L2VM provisioned PWs, therefore the PW Set will have a single member, and this set index can be set to the pwIndex in the pwTable of that PW. This form of binding is known as a double-sided binding since the PW(s) must be provisioned in the pwTable at each end of the virtual circuit. - If auto-discovery is enabled (vpwsConfigADType = bgp) then the VPWS service establishes a PW between each pair of VPWS sites within the VPWS, using BGP auto-discovery to determine which PE router hosts each VPWS site. In this case, each AC is bound to a PW that is identified by the local and remote site IDs. The PE router creates these PWs automatically as a result of the BGP auto-discovery process. This form of configuration is sometimes known as 'colored pools'. In this approach the operator configures a pool of ACs for each local site, and each pool is identified by a site ID or 'color'. The VPWS service establishes a PW between each pair of 'colored pools' (VPWS sites), and each AC is bound to a PW associated with the same 'colored pool' (local site ID). - If auto-discovery is enabled (vpwsConfigADType = bgp) then an AC can still be bound to a PW that is provisioned in the pwTable MIB, for example to incorporate a legacy PE router that does not support auto-discovery into the VPWS. The method for associating ACs with other ACs in a hairpin also depends on whether auto-discovery is enabled. - If auto-discovery is disabled, the AC is bound to another AC directly, by configuring its interface index in this table. In this case the PW set index can also optionally be specified to provide redundant connectivity to the other site. - If auto-discovery is enabled, the BGP auto-discovery process ascertains that this PE router also hosts the remote site, and automatically binds the two ACs. In either case a row in this table only establishes unidirectional connectivity for a hairpin. For full connectivity, the opposite direction will need to be configured in the same manner (though this need not be in the same VPWS instance). Each VPWS Binding is configured with a PW binding type, given by vpwsBindCfgPwBindType, which specifies whether the PW Set to which the AC is bound is identified by a PW Set index and/or hairpin interface index (and so is provisioned) or by a local and remote site ID (and so is auto-created as a result of BGP auto-discovery). This table is indexed on AC interface index to ensure that each AC is only ever bound to a single VPWS. The read-only vpwsBindTable can be used to show the ACs bound to each VPWS. Note that changes to this table may cause the corresponding AC to go operationally down as it may involve re-programming the AC in the data plane." ::= { vpwsObjects 3 } vpwsBindCfgEntry OBJECT-TYPE SYNTAX VpwsBindCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents a configured VPWS binding." INDEX { l2vmEntityIndex, ifIndex } ::= { vpwsBindCfgTable 1 } VpwsBindCfgEntry ::= SEQUENCE { vpwsBindCfgRowStatus RowStatus, vpwsBindCfgAdminStatus AdminStatus, vpwsBindCfgOperStatus NpgOperStatus, vpwsBindCfgVpwsIndex NumericIndexOrZero, vpwsBindCfgPwBindType L2vpnPwBindType, vpwsBindCfgPwSetIndex Unsigned32, vpwsBindCfgRemoteSiteID L2vpnVeIdOrZero, vpwsBindCfgLclSwitchIfIndex InterfaceIndexOrZero } vpwsBindCfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status for this VPWS Binding Configuration Table entry, used to create and destroy table entries." ::= { vpwsBindCfgEntry 3 } vpwsBindCfgAdminStatus OBJECT-TYPE SYNTAX AdminStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The administrative status of this VPWS binding, used to activate and deactivate the VPWS binding." DEFVAL { adminStatusUp } ::= { vpwsBindCfgEntry 4 } vpwsBindCfgOperStatus OBJECT-TYPE SYNTAX NpgOperStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational status of this VPWS binding. If the operational status is 'up' then the cross-connect for this binding is programmed in the data plane." ::= { vpwsBindCfgEntry 5 } vpwsBindCfgVpwsIndex OBJECT-TYPE SYNTAX NumericIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "Index identifying the VPWS instance. This field must be set to a non-zero value before the VPWS binding can go into operational status 'up'. Changing this value will cause an interruption to data flow from this AC onto the VPWS." DEFVAL { 0 } ::= { vpwsBindCfgEntry 6 } vpwsBindCfgPwBindType OBJECT-TYPE SYNTAX L2vpnPwBindType MAX-ACCESS read-create STATUS current DESCRIPTION "The VPWS pseudowire (PW) binding type. This field specifies the identifiers used for the PW to which the AC is bound. If the PW is provisioned in the pwTable, then it is identified by an index into the pwTable MIB. In this case, this field must be set to pwMibIndex, and the pwTable MIB index must be set in vpwsBindCfgPwSetIndex. If the PW is created as a result of BGP auto-discovery, then it is identified by a local and remote VE ID. For a VPWS, the VE ID is equal to the VPWS Site ID. In this case, this field must be set to lclRmtVeId, and the remote VPWS Site ID for the PW must be set in vpwsBindCfgRemoteSiteID. The local VPWS Site ID is the value set in vpwsConfigLocalSiteID. It is not valid to set this field to lclRmtVeId unless auto-discovery is enabled (vpwsConfigADType = bgp). If this field is set to lclRmtVeId for any other value of vpwsConfigADType, then vpwsBindCfgOperStatus is set to operStatusFailedPerm. Changing this value will cause an interruption to data flow from this AC onto the VPWS." DEFVAL { pwMibIndex } ::= { vpwsBindCfgEntry 7 } vpwsBindCfgPwSetIndex OBJECT-TYPE SYNTAX Unsigned32 (0..1073741823) MAX-ACCESS read-create STATUS current DESCRIPTION "Index for the set of PWs to which the AC should be bound. The AC is bound to every PW in the pwTable with pwRedundancySetId set to this value. This is only used if the PW is provisioned in the pwTable MIB, that is if vpwsBindCfgPwBindType = pwMibIndex. Changing this value will cause an interruption to data flow from this AC onto the VPWS." DEFVAL { 0 } ::= { vpwsBindCfgEntry 8 } vpwsBindCfgRemoteSiteID OBJECT-TYPE SYNTAX L2vpnVeIdOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "The remote VPWS site ID of the PW to bind the AC to, or zero if not specified. This is only used if the pseudowire (PW) is created as a result of BGP auto-discovery, that is if vpwsBindCfgPwBindType = lclRmtVeId. If vpwsBindCfgPwBindType = lclRmtVeId then the AC is bound to a PW that connects the local VPWS site (vpwsConfigLocalSiteID) to the remote VPWS site, using auto-discovery to determine the remote PE router that hosts the remote VPWS site. This remote VPWS site ID should match the local VPWS site ID configured on the remote PE router. The valid range for VPWS site IDs depends on whether LDP or BGP signaling is used. - For LDP signaling (vpwsConfigSigType = ldp) the valid range is 1-4294967295 (4 bytes). - For BGP signaling (vpwsConfigSigType = bgp) the valid range is 1-65535 (2 bytes). Changing this value will cause an interruption to data flow from this AC onto the VPWS." DEFVAL { 0 } ::= { vpwsBindCfgEntry 9 } vpwsBindCfgLclSwitchIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "Interface index that the AC should be bound to directly, via a layer 2 local switching rule (hairpin). Only relevant if the local PE hosts both VPWS sites concerned in this binding; otherwise, should be set to zero. This is only used if the PW is provisioned in the pwTable MIB, that is if vpwsBindCfgPwBindType = pwMibIndex." DEFVAL { 0 } ::= { vpwsBindCfgEntry 10 } -- End VPWS Binding Config Table ------------------------------------------------------------------------------- -- -- VPWS Binding Table (READ-ONLY). -- vpwsBindTable OBJECT-TYPE SYNTAX SEQUENCE OF VpwsBindEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "VPWS Binding Table (read-only). This table displays the Attachment Circuit (AC) bindings in a VPWS. Bindings are configured in the vpwsBindCfgTable. This table is read-only." ::= { vpwsObjects 4 } vpwsBindEntry OBJECT-TYPE SYNTAX VpwsBindEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents a VPWS binding." INDEX { l2vmEntityIndex, vpwsIndex, ifIndex } ::= { vpwsBindTable 1 } VpwsBindEntry ::= SEQUENCE { vpwsBindOperStatus NpgOperStatus, vpwsBindPwBindType L2vpnPwBindType, vpwsBindPwSetIndex NumericIndex, vpwsBindPwIfIndex InterfaceIndex, vpwsBindLocalSiteID L2vpnVeIdOrZero, vpwsBindRemoteSiteID L2vpnVeIdOrZero, vpwsBindLclSwitchIfIndex InterfaceIndex, vpwsBindRemoteRD BgpRouteDistinguisher, vpwsBindRemoteAddrType InetAddressType, vpwsBindRemoteAddr InetAddress } vpwsBindOperStatus OBJECT-TYPE SYNTAX NpgOperStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational status of this VPWS binding. If the operational status is 'up' then the cross-connect for this binding is programmed in the data plane." ::= { vpwsBindEntry 4 } vpwsBindPwBindType OBJECT-TYPE SYNTAX L2vpnPwBindType MAX-ACCESS read-only STATUS current DESCRIPTION "If the AC is bound to a pseudowire (PW) that is provisioned in the pwTable, then this field is set to pwMibIndex. If the AC is bound to a pseudowire that has been created as a result of BGP auto-discovery, then this field is set to lclRmtVeId. In this case, the PW is identified by the local and remote VPWS Site IDs. The local VPWS Site ID is stored in vpwsBindLocalSiteID, and the remote VPWS Site ID is stored in vpwsBindRemoteSiteID." ::= { vpwsBindEntry 5 } vpwsBindPwSetIndex OBJECT-TYPE SYNTAX NumericIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The PW set index of the PWs bound to this AC. The AC is bound to the (redundant) set of PWs corresponding to rows in the pwTable with pwRedundancySetId set to this value. If the vpwsBindPwBindType is pwMibIndex, then this value will match the configured vpwsBindCfgPwSetIndex. Otherwise the PW set index is determined when the pseudowire is created following auto-discovery of the remote site." ::= { vpwsBindEntry 6 } vpwsBindPwIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index that has been assigned for the set of pseudowires to which this AC is bound." ::= { vpwsBindEntry 7 } vpwsBindLocalSiteID OBJECT-TYPE SYNTAX L2vpnVeIdOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The local VPWS site ID to which this AC is bound, or zero if not applicable. This is only relevant if vpwsBindPwBindType = lclRmtVeId. If vpwsBindPwBindType = lclRmtVeId then the AC is bound to a pseudowire that connects the local VPWS site to the remote VPWS site, using auto-discovery to determine the remote PE router that hosts the remote VPWS site." ::= { vpwsBindEntry 8 } vpwsBindRemoteSiteID OBJECT-TYPE SYNTAX L2vpnVeIdOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The remote VPWS site ID to which this AC is bound, or zero if not applicable. This is only relevant if vpwsBindPwBindType = lclRmtVeId. If vpwsBindPwBindType = lclRmtVeId then the AC is bound to a pseudowire that connects the local VPWS site to the remote VPWS site, using auto-discovery to determine the remote PE router that hosts the remote VPWS site." ::= { vpwsBindEntry 9 } vpwsBindLclSwitchIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index of the AC bound to this AC directly in a layer 2 local switching rule (hairpin). If the vpwsBindPwBindType is pwMibIndex, then this value will match the configured vpwsBindCfgLclSwitchIfIndex. Otherwise, the hairpin interface index is determined when the auto-discovery process learns that the remote site is hosted at the local PE router. This field is zero if the remote site is not hosted at the local PE router." ::= { vpwsBindEntry 10 } vpwsBindRemoteRD OBJECT-TYPE SYNTAX BgpRouteDistinguisher MAX-ACCESS read-only STATUS current DESCRIPTION "The remote route distinguisher, or null if not known. This is the route distinguisher of the best BGP route advertising the remote VPWS site ID. This is only relevant if vpwsBindPwBindType = lclRmtVeId." ::= { vpwsBindEntry 11 } vpwsBindRemoteAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The address family of the remote address. This is only relevant if vpwsBindPwBindType = lclRmtVeId." ::= { vpwsBindEntry 12 } vpwsBindRemoteAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The remote address, or null if not known. This is the address of the router advertising the best BGP route to the remote VPWS site ID. This is only relevant if vpwsBindPwBindType = lclRmtVeId." ::= { vpwsBindEntry 13 } -- End of VPWS Binding Table. ------------------------------------------------------------------------------- -- -- Conformance statement -- vpwsCompliances OBJECT IDENTIFIER ::= { vpwsConformance 1 } vpwsGroups OBJECT IDENTIFIER ::= { vpwsConformance 2 } -- -- Module compliance is divided into two categories. -- - Full compliance. -- - Support for double-sided bindings only. -- - Support for auto-discovered bindings only. -- vpwsFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The module is implemented with support for double-sided bindings and auto-created bindings using BGP auto-discovery." MODULE -- this module MANDATORY-GROUPS { vpwsBaseGroup, vpwsDoubleSidedGroup, vpwsBgpADGroup } ::= { vpwsCompliances 1 } vpwsDoubleSidedCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The module is implemented with support for double-sided bindings only." MODULE -- this module MANDATORY-GROUPS { vpwsBaseGroup, vpwsDoubleSidedGroup } ::= { vpwsCompliances 2 } vpwsBgpADCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The module is implemented with support for BPG auto-discovery only." MODULE -- this module MANDATORY-GROUPS { vpwsBaseGroup, vpwsBgpADGroup } ::= { vpwsCompliances 3 } vpwsBaseGroup OBJECT-GROUP OBJECTS { vpwsConfigRowStatus, vpwsConfigAdminStatus, vpwsConfigOperStatus, vpwsConfigName, vpwsConfigDescr, vpwsConfigADType, vpwsConfigSigType, vpwsConfigPwEncapType, vpwsConfigMtu, vpwsConfigControlWord, vpwsConfigSeqDelivery, vpwsStatusOperStatus, vpwsStatusVcCount, vpwsStatusDesignatedForwarder, vpwsBindCfgRowStatus, vpwsBindCfgAdminStatus, vpwsBindCfgOperStatus, vpwsBindCfgVpwsIndex, vpwsBindCfgPwBindType, vpwsBindCfgPwSetIndex, vpwsBindOperStatus, vpwsBindPwBindType, vpwsBindPwSetIndex, vpwsBindPwIfIndex, vpwsBindLclSwitchIfIndex, vpwsBindRemoteRD, vpwsBindRemoteAddrType, vpwsBindRemoteAddr } STATUS current DESCRIPTION "Objects relating to common VPWS configuration." ::= { vpwsGroups 1 } vpwsDoubleSidedGroup OBJECT-GROUP OBJECTS { vpwsBindCfgPwSetIndex, vpwsBindCfgLclSwitchIfIndex } STATUS current DESCRIPTION "Objects specifically relating to configuration of a VPWS with double-sided bindings." ::= { vpwsGroups 2 } vpwsBgpADGroup OBJECT-GROUP OBJECTS { vpwsConfigRouteDistinguisher, vpwsConfigVpnId, vpwsConfigLocalSiteID, vpwsConfigLocalPreference, vpwsConfigLabelBlockSize, vpwsConfigIncludeCSV, vpwsConfigIgnoreMtuMismatch, vpwsConfigIgnoreEncapsMismatch, vpwsBindCfgRemoteSiteID, vpwsBindLocalSiteID, vpwsBindRemoteSiteID } STATUS current DESCRIPTION "Objects specifically relating to configuration of a VPWS with BGP auto-discovery." ::= { vpwsGroups 3 } ------------------------------------------------------------------------------- END