AFFIRMED-MME-TRAPS-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32, Counter32, Gauge32, Unsigned32, Counter64, enterprises FROM SNMPv2-SMI mgmt, NetworkAddress, IpAddress, Counter, Gauge, TimeTicks FROM RFC1155-SMI PhysAddress, DisplayString, DateAndTime, TruthValue, AutonomousType, RowPointer, RowStatus, TEXTUAL-CONVENTION FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- [RFC3411] Ipv6Address FROM IPV6-TC alarmListName, alarmModelIndex, alarmModelState, alarmActiveDateAndTime, alarmActiveIndex FROM ALARM-MIB -- [RFC3877] ItuPerceivedSeverity FROM ITU-ALARM-TC-MIB; affirmedSnmpMmeTraps MODULE-IDENTITY LAST-UPDATED "201609010000Z" ORGANIZATION "Affirmed Networks, Inc." CONTACT-INFO "Affirmed Networks, Inc. 35 Nagog Park Acton, MA USA " DESCRIPTION "Traps for MME/SGSN" REVISION "201609010000Z" DESCRIPTION "MME10.0 Release" ::= { enterprises 37963 4 0 6 } anMmeTrapAlarms OBJECT IDENTIFIER ::= { affirmedSnmpMmeTraps 1 } anMmeTrapEvents OBJECT IDENTIFIER ::= { affirmedSnmpMmeTraps 2 } anMmeNotificationVars OBJECT IDENTIFIER ::= { affirmedSnmpMmeTraps 3 } anMmeAlarmState OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..6)) MAX-ACCESS read-only STATUS current DESCRIPTION "Alarm state:: create : alarm is set delete : alarm is cleared log : log message" ::= { anMmeNotificationVars 1 } anMmeAlarmSeverity OBJECT-TYPE SYNTAX ItuPerceivedSeverity MAX-ACCESS read-only STATUS current DESCRIPTION "Alarm severity:: 1: CLEARED 2: INDETERMINATE 3: CRITICAL 4: MAJOR 5: MINOR 6: WARNING" ::= { anMmeNotificationVars 2 } anMmeEntityTag OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "location of alarm resource descripted by location-information-type." ::= { anMmeNotificationVars 3 } anMmeSubentityInfo OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "additional information of entity" ::= { anMmeNotificationVars 4 } anMmeLocationGateway OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..512)) MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Gateway Location Information" ::= { anMmeNotificationVars 5 } anMmeReason OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "Reason Information" ::= { anMmeNotificationVars 6 } anMmeAlarmDateAndTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "Reason Information" ::= { anMmeNotificationVars 7 } anMmeGroupKey OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "Group Key" ::= { anMmeNotificationVars 8 } anMmeSequenceNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Sequence Number" ::= { anMmeNotificationVars 9 } anMmeFirstEvent OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "Time of first occurance of this alarm" ::= { anMmeNotificationVars 10 } anMmeLastEvent OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "Time of last occurance of this alarm" ::= { anMmeNotificationVars 11 } anMmeLocation OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "Location of the entity that generated the alarm" ::= { anMmeNotificationVars 12 } anMmeService OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "Service of the entity that generated the alarm" ::= { anMmeNotificationVars 13 } anMmeAlarmIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Alarm Index" ::= { anMmeNotificationVars 14 } anMmeTrapAlarmNm1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "One or more VM types are not available." -- REPAIR-ACTION -- "Check current status as reflected by the status system command versus configured -- services and units. Analyze the list of missing units in the reason text -- field of this alarm and add them to the configuration and unlock them." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 65536001 } anMmeTrapAlarmNm1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A configured VM is currently unlocked and disabled." -- REPAIR-ACTION -- "Check the health of the related server, check cables. Consider locking -- and unlocking the callP VM. Contact your next level support if necessary." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 65536002 } anMmeTrapAlarmNm1302 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Software upgrade state" -- REPAIR-ACTION -- "This alarm will automatically clear when the upgrade state ends, either -- normally or forcibly, as controlled by the software upgrade-state commands." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 65536003 } anMmeTrapAlarmNm1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 65536099 } anMmeTrapAlarmResmon1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The Trace file system is full." -- REPAIR-ACTION -- "Consider changing the parition size." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 66191361 } anMmeTrapAlarmResmon1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 66191459 } anMmeTrapAlarmGaBilling1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Collected charging information has crossed disk usage thresholds." -- REPAIR-ACTION -- "Off-load collected charging information from the disk or adjust the backup -- retention interval at epc interface ga ga-if backup-file-retention. Alarm -- thresholds are configurable at epc interface ga ga-if disk-alarm-thresholds. -- " -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133693441 } anMmeTrapAlarmGaBilling1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "CGF connection status" -- REPAIR-ACTION -- "Check the health of the remote equipment and the health of the IP network." -- ENTITY-TYPE -- "cgf" -- ::= { anMmeTrapAlarms 133693443 } anMmeTrapAlarmGaBilling1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133693539 } anMmeTrapAlarmLi1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "LI data is out of synchronization." -- REPAIR-ACTION -- "No immediate action required. The active and standby callP VMs (if available) -- automatically attempt to resynchronize with each other. If condition persists, -- contact your next level of support." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133758977 } anMmeTrapAlarmLi1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Target database is at predefined capacity level or is full." -- REPAIR-ACTION -- "No action required" -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133758978 } anMmeTrapAlarmLi1302 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Number of active targets exceed the provisioned active targets." -- REPAIR-ACTION -- "Increase the provisioning attribute maxActiveTargets value." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133758979 } anMmeTrapAlarmLi1303 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Failed to establish connection to the ADMF." -- REPAIR-ACTION -- "Check the configured admf-ip-address and admf-port under "epc interface -- x lig", and check the health of the IP network." -- ENTITY-TYPE -- "x1" -- ::= { anMmeTrapAlarms 133758980 } anMmeTrapAlarmLi1304 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Failed to establish connection to one or more DF2s." -- REPAIR-ACTION -- "Verify the health of DF2 and IP network." -- ENTITY-TYPE -- "x2" -- ::= { anMmeTrapAlarms 133758981 } anMmeTrapAlarmLi1305 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected in the LI Manager process." -- REPAIR-ACTION -- "Contact your next level of support. Consider switching over to the standby -- callP VM and then locking and unlocking the former active, now standby, -- callP VM." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133758982 } anMmeTrapAlarmLi1306 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Failed to establish connection to one or more DF3s." -- REPAIR-ACTION -- "Verify the health of DF3 and IP network." -- ENTITY-TYPE -- "x3" -- ::= { anMmeTrapAlarms 133758983 } anMmeTrapAlarmLi1307 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected in the LI Agent process." -- REPAIR-ACTION -- "Contact your next level of support. Consider switching over to the standby -- callP VM and then locking and unlocking the former active, now standby, -- callP VM." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133758984 } anMmeTrapAlarmLi1308 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Failed to establish connection to the named DF2." -- REPAIR-ACTION -- "Verify the health of DF2 and IP network." -- ENTITY-TYPE -- "x2-if df" -- ::= { anMmeTrapAlarms 133758985 } anMmeTrapAlarmLi1309 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Failed to establish connection to the named DF3." -- REPAIR-ACTION -- "Verify the health of DF3 and IP network." -- ENTITY-TYPE -- "x3-if df" -- ::= { anMmeTrapAlarms 133758986 } anMmeTrapAlarmLi1310 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "LI buffering for IRI messages is occurring, buffer utilization is reported." -- REPAIR-ACTION -- "Verify the health of DF2 and IP network. If the reason string includes -- a warning that the buffer size is reduced due to VM memory size allocation, -- please check 'size-mem' from 'show vm service rm detail' and consider redeploying -- the RM VM with more memory to accommodate LI buffering." -- ENTITY-TYPE -- "x2-if df" -- ::= { anMmeTrapAlarms 133758987 } anMmeTrapAlarmLi1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133759075 } anMmeTrapAlarmMmeRm1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Data maintained by the MME Resource Manager is out of synchronization." -- REPAIR-ACTION -- "No immediate action required. The active and standby callP VMs (if available) -- automatically attempt to resynchronize with each other. If condition persists, -- contact product support organization." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133824513 } anMmeTrapAlarmMmeRm1302 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected." -- REPAIR-ACTION -- "Contact product support organization. Consider switching over to the standby -- callP VM and then locking and unlocking the former active, now standby, -- callP VM." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133824514 } anMmeTrapAlarmMmeRm1303 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A critical MME application is missing." -- REPAIR-ACTION -- "Verify that for each listed critical application, at least one callP VM -- is added, loaded, and unlocked through the AMF CLI." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133824515 } anMmeTrapAlarmMmeRm1304 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Unknown RAI received." -- REPAIR-ACTION -- "Use the CLI command "show epc service-area routing-area-unknown" to list -- the unknown RAI. Determine if the access equipment is mis-configured or -- if the SGSN needs to support those routing areas. If the latter, then use -- the CLI command "set epc service-area routing-area" to configure additional -- routing areas for the applicable RNC and NSE on that SGSN. " -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133824516 } anMmeTrapAlarmMmeRm1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133824611 } anMmeTrapAlarmMmeS1M1302 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected. " -- REPAIR-ACTION -- "Contact product support organization. Consider switching over to the standby -- callP VM and then locking and unlocking the former active, now standby, -- callP VM. " -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133890051 } anMmeTrapAlarmMmeS1M1303 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Maximum number of enodeBs has been reached." -- REPAIR-ACTION -- "Correct the configuration on the MME by adding the S1Listener callP VMs -- or by reducing the number of enodeBs configured in the network" -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133890052 } anMmeTrapAlarmMmeS1M1304 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Maximum number of tracking areas has been reached." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133890053 } anMmeTrapAlarmMmeS1M1305 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "One or more enodeB connections are being refused." -- REPAIR-ACTION -- "Check configuration of eNodeBs and MME." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133890054 } anMmeTrapAlarmMmeS1M1306 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "One or more enodeBs are no longer reachable." -- REPAIR-ACTION -- "Check health of enodeB and IP network." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133890055 } anMmeTrapAlarmMmeS1M1307 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "An incorrect MME code was received from the MME." -- REPAIR-ACTION -- "Verify if MME is configured correctly." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133890056 } anMmeTrapAlarmMmeS1M1308 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Maximum number of MCEs has been reached" -- REPAIR-ACTION -- "Correct the configuration on the MME by adding the S1Listener callP VMs -- or by reducing the number of MCEs configured in the network. Or adjusting -- the configured limit under epc engineering s1-capacity max-enodebs." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133890057 } anMmeTrapAlarmMmeS1M1309 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Maximum number of service areas has been reached" -- REPAIR-ACTION -- "Contact your next level of support." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133890058 } anMmeTrapAlarmMmeS1M1310 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "One or more MCEs are no longer reachable" -- REPAIR-ACTION -- "Check health of MCEs and IP network." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133890059 } anMmeTrapAlarmMmeS1M1311 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "EnodeB SCTP Congestion." -- REPAIR-ACTION -- "Check health of eNodeBs and the SCTP associations." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133890060 } anMmeTrapAlarmMmeS1M1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133890147 } anMmeTrapAlarmMmeUpsm1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All RADIUS peers provisioned for use by the Fxa interface are unreachable." -- REPAIR-ACTION -- "Verify the health of the remote equipment and the health of the IP network." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133955585 } anMmeTrapAlarmMmeUpsm1302 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Maximum number of S11 paths has been reached." -- REPAIR-ACTION -- "Contact product support organization." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133955587 } anMmeTrapAlarmMmeUpsm1303 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Maximum number of S10 paths has been reached." -- REPAIR-ACTION -- "Contact product support organization." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133955588 } anMmeTrapAlarmMmeUpsm1304 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Maximum number of Gn paths has been reached." -- REPAIR-ACTION -- "Contact product support organization." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133955589 } anMmeTrapAlarmMmeUpsm1305 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Maximum number of S3 paths has been reached." -- REPAIR-ACTION -- "Contact product support organization." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133955590 } anMmeTrapAlarmMmeUpsm1306 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Failure of one or more GTP paths." -- REPAIR-ACTION -- "Check health of remote SGWs, MMEs, SGSN eANs or MBMS-GWs, and IP network." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133955591 } anMmeTrapAlarmMmeUpsm1307 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Maximum number of S4 paths has been reached." -- REPAIR-ACTION -- "Contact product support organization." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133955592 } anMmeTrapAlarmMmeUpsm1308 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Maximum number of S16 paths has been reached." -- REPAIR-ACTION -- "Contact product support organization." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133955593 } anMmeTrapAlarmMmeUpsm1309 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Maximum number of Sv paths has been reached." -- REPAIR-ACTION -- "Contact product support organization." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133955594 } anMmeTrapAlarmMmeUpsm1310 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Maximum number of Sm paths has been reached." -- REPAIR-ACTION -- "Contact your next level of support." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133955595 } anMmeTrapAlarmMmeUpsm1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 133955683 } anMmeTrapAlarmMmeIlf1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Data maintained by the MME IMSI Locator Function is out of synchronization." -- REPAIR-ACTION -- "No immediate action required. The active and standby callP VMs (if available) -- automatically attempt to resynchronize with each other. If condition persists, -- contact product support organization." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134021121 } anMmeTrapAlarmMmeIlf1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected." -- REPAIR-ACTION -- "Contact product support organization. Consider switching over to the standby -- callP VM and then locking and unlocking the former active, now standby, -- callP VM." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134021122 } anMmeTrapAlarmMmeIlf1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134021219 } anMmeTrapAlarmMmeS1Server1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "EnodeB Process creation failed." -- REPAIR-ACTION -- "Check the health of the 'blade/vm' supporting this callP VM (as identified -- in the ref-entity-tag of the alarm). " -- ENTITY-TYPE -- "mme-s1-interface" -- ::= { anMmeTrapAlarms 134086657 } anMmeTrapAlarmMmeS1Server1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected." -- REPAIR-ACTION -- "Contact product support organization. Consider locking and unlocking the -- callP VM." -- ENTITY-TYPE -- "mme-s1-interface" -- ::= { anMmeTrapAlarms 134086658 } anMmeTrapAlarmMmeS1Server1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "mme-s1-interface" -- ::= { anMmeTrapAlarms 134086755 } anMmeTrapAlarmMmeS1Enb1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected." -- REPAIR-ACTION -- "Contact product support organization. Consider locking and unlocking the -- callP VM." -- ENTITY-TYPE -- "mme-s1-interface" -- ::= { anMmeTrapAlarms 134152193 } anMmeTrapAlarmMmeS1Enb1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "mme-s1-interface" -- ::= { anMmeTrapAlarms 134152291 } anMmeTrapAlarmMmeDc1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Diameter peer is unreachable." -- REPAIR-ACTION -- "Verify health of the HSS and/or EIR and the IP network." -- ENTITY-TYPE -- "mme-diameter-peer" -- ::= { anMmeTrapAlarms 134217729 } anMmeTrapAlarmMmeDc1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected." -- REPAIR-ACTION -- "Contact product support organization. Consider locking and unlocking the -- callP VM." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134217730 } anMmeTrapAlarmMmeDc1302 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "There are no peers on the Diameter Client that supports S6a interface." -- REPAIR-ACTION -- "Verify health of the HSS and the IP network." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134217731 } anMmeTrapAlarmMmeDc1303 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "There are no peers on the Diameter Client that supports S13 interface." -- REPAIR-ACTION -- "Verify health of the EIR and the IP network." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134217732 } anMmeTrapAlarmMmeDc1304 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The Diameter Client application is experiencing congestion." -- REPAIR-ACTION -- "No immediate action is required by the operator, but if the condition persists, -- investigate the HSS and/or DIAMETER agent's performance." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134217733 } anMmeTrapAlarmMmeDc1305 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "There are no peers on the Diameter Client that support SLg interface." -- REPAIR-ACTION -- "Verify the correct peers are configured on the MME. Also verify IP connectivity -- to the peer from the MME." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134217734 } anMmeTrapAlarmMmeDc1306 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "There are no peers on the Diameter Client that support SGd interface." -- REPAIR-ACTION -- "Verify the correct peers are configured on the MME. Also verify IP connectivity -- to the peer from the MME." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134217735 } anMmeTrapAlarmMmeDc1307 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "There are no peers on the Diameter Client that support T6a interface." -- REPAIR-ACTION -- "Verify the correct peers are configured on the C-SGN/MME. Also verify -- IP connectivity to the peer from the C-SGN/MME." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134217736 } anMmeTrapAlarmMmeDc1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134217827 } anMmeTrapAlarmMmeSc1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Attach success rate(E-UTRAN) has fallen below the prov threshold." -- REPAIR-ACTION -- "Examine the mmeMm attach failure counters and verify the health of the -- network." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283266 } anMmeTrapAlarmMmeSc1302 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Session act success rate(E-UTRAN) has fallen below the prov threshold." -- REPAIR-ACTION -- "Examine the mmeSm default bearer activation failure counters and verify -- the health of the network." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283267 } anMmeTrapAlarmMmeSc1303 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Bearer act success rate(E-UTRAN) has fallen below the prov threshold." -- REPAIR-ACTION -- "Examine the mmeSm dedicated bear activation failure counters and verify -- the health of the network." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283268 } anMmeTrapAlarmMmeSc1304 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Subscriber data is out of synchronization." -- REPAIR-ACTION -- "No immediate action required. The active and standby callP VMs (if available) -- automatically attempt to resynchronize with each other. If condition persists, -- contact product support organization." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283269 } anMmeTrapAlarmMmeSc1305 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected." -- REPAIR-ACTION -- "Contact product support organization. Consider switching over to the standby -- callP VM and then locking and unlocking the former active, now standby, -- callP VM." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283270 } anMmeTrapAlarmMmeSc1310 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The SC application is experiencing congestion." -- REPAIR-ACTION -- "No immediate action is required by the operator. The Subscriber Control -- function triggers abatement action when the congestion level exceeds the -- configured threshold." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283271 } anMmeTrapAlarmMmeSc1311 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Abatement action is being applied to address congestion overload." -- REPAIR-ACTION -- "No action required by the operator. The Subscriber Control function is -- taking the abatement action described in the alarm." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283272 } anMmeTrapAlarmMmeSc1306 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The no. of attached subscribers is approaching the max allowed for this SU." -- REPAIR-ACTION -- "No immediate action required by the operator. The Subscriber Control function -- triggers abatement action on a per MPU basis when the attached subscriber -- count exceeds the configured threshold." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283273 } anMmeTrapAlarmMmeSc1307 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Abatement action is being applied to address subscriber overload." -- REPAIR-ACTION -- "No action required by the operator. The Subscriber Control function is -- taking the abatement action described in the alarm." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283274 } anMmeTrapAlarmMmeSc1308 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The no. of activated bearers is approaching the max allowed for this SU." -- REPAIR-ACTION -- "No immediate action required by the operator. The Subscriber Control function -- triggers abatement action when the number of bearers exceeds the configured -- threshold." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283275 } anMmeTrapAlarmMmeSc1309 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Abatement action is being applied to address bearer overload." -- REPAIR-ACTION -- "No action required by the operator. The Subscriber Control function is -- taking the abatement action described in the alarm." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283276 } anMmeTrapAlarmMmeSc1320 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "eAN not found for CDMA2000 uplink message." -- REPAIR-ACTION -- "Check the configured 'epc interface s101 ean' table to ensure there is -- a mapping for the access-id." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283277 } anMmeTrapAlarmMmeSc1312 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Number of MAP dialogues reaches the high water mark." -- REPAIR-ACTION -- "Contact product support organization personnel." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283278 } anMmeTrapAlarmMmeSc1313 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Attach success rate for GPRS subscribers crosses the thresholds." -- REPAIR-ACTION -- "Examine the GMM attach failure counters and verify the health of the network. -- In other cases, contact product support organization." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283279 } anMmeTrapAlarmMmeSc1314 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Activation success rate for GPRS subscribers crosses the thresholds." -- REPAIR-ACTION -- "Examine the SM activation failure counters and verify the health of the -- network. In other cases, contact product support organization." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283280 } anMmeTrapAlarmMmeSc1315 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Attach success rate for UMTS subscribers crosses the thresholds." -- REPAIR-ACTION -- "Examine the GMM attach failure counters and verify the health of the network.In -- other cases, contact product support organization." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283281 } anMmeTrapAlarmMmeSc1316 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Activation success rate for UMTS subscribers crosses the thresholds." -- REPAIR-ACTION -- "Examine the SM activation failure counters and verify the health of the -- network.In other cases contact product support organization." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283282 } anMmeTrapAlarmMmeSc1317 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Attach, IRAU, and/or activation attempts have exceeded thresholds." -- REPAIR-ACTION -- "This alarm is informational and may require no action depending on policies -- in place for a particular network regarding traffic levels per network -- code and country code. In other cases contact product support organization." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283283 } anMmeTrapAlarmMmeSc1318 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Traffic levels have exceeded thresholds for load-controlled PLMNs." -- REPAIR-ACTION -- "This alarm is informational and may require no action depending on policies -- in place for a particular network regarding traffic levels per network -- code and country code. In other cases contact product support organization." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283284 } anMmeTrapAlarmMmeSc1321 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "IWS not found for CDMA2000 uplink message." -- REPAIR-ACTION -- "Check the configured 'epc interface s102 iws' table to ensure there is -- a mapping for the cell IDs." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283288 } anMmeTrapAlarmMmeSc1322 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "MME received A21-Ack message with cause Unknown Cell Identifier from IWS." -- REPAIR-ACTION -- "Check the network configuration to ensure the cell IDs are correctly set -- up across the network." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283289 } anMmeTrapAlarmMmeSc1323 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "SLN monitored UE is connected to MME." -- REPAIR-ACTION -- "None. This alarm is cleared when the UE is not connected, monitoring of -- the UE ends by means of removing the configuration, or upon timer expiration." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283290 } anMmeTrapAlarmMmeSc1324 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The number of CAMEL dialogues exceeds 95% of the configured maximum." -- REPAIR-ACTION -- "Contact product support organization personnel." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283291 } anMmeTrapAlarmMmeSc1325 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "MSC/VLR Discovery for SRVCC." -- REPAIR-ACTION -- " Check configuration under epc interface sv sv-if for the selected vlr-discovery -- method. Then check under epc service-area for tracking-area to location-area -- mapping, and location-area to vlr-pool mapping, and vlr-pool to vlr mapping, -- and finally check that the desired vlr has an sv-ip-address-list configured." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283292 } anMmeTrapAlarmMmeSc1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134283363 } anMmeTrapAlarmMmeUpm1303 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The UPM application is experiencing congestion." -- REPAIR-ACTION -- "No immediate action is required by the operator. The Subscriber Control -- function triggers abatement action." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134545409 } anMmeTrapAlarmMmeUpm1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A RADIUS peer used by Fxa interface is unreachable." -- REPAIR-ACTION -- "Verify the health of the remote equipment and the health of the IP network." -- ENTITY-TYPE -- "mme-radius-peer" -- ::= { anMmeTrapAlarms 134545410 } anMmeTrapAlarmMmeUpm1304 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "UPM Transaction Rate Congestion" -- REPAIR-ACTION -- "The operator needs to take an action by relocating the paths using one -- or more of the following commands as the case may be " -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134545411 } anMmeTrapAlarmMmeUpm1302 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Failure of UDP connection to IWS for S102 interface." -- REPAIR-ACTION -- "Check if the IP address of the 'epc interface s102 iws' entity is configured -- properly and check if the IWS is down." -- ENTITY-TYPE -- "mme-iws" -- ::= { anMmeTrapAlarms 134545412 } anMmeTrapAlarmMmeUpm1305 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Failure of GTP connection to MBMS-GW for Sm interface." -- REPAIR-ACTION -- "Check if the MBMS-GW is down." -- ENTITY-TYPE -- "mbms-gw" -- ::= { anMmeTrapAlarms 134545413 } anMmeTrapAlarmMmeUpm1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 134545507 } anMmeTrapAlarmMmeSigtran1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "No destinations are routable." -- REPAIR-ACTION -- ""Check the details of the remote destination using the command 'show epc -- interface ss7 remote-dest ...' for indication of why the destination is -- unreachable."" -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 135593985 } anMmeTrapAlarmMmeSigtran1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "No provisioned SIGTRAN signaling gateways are reachable." -- REPAIR-ACTION -- ""Check the operational status of the remote peers under "epc interface -- ss7 peer" for those peers of type sgp. To determine a peer type, check -- configuration under "epc interface ss7 peer peer-type"" -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 135593986 } anMmeTrapAlarmMmeSigtran1302 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The peer process is unavailable for routing purposes." -- REPAIR-ACTION -- ""Check the status of the destination by using the command 'show epc interface -- ss7 remote-dest ...' for 'peer' components"." -- ENTITY-TYPE -- "mme-g-peer" -- ::= { anMmeTrapAlarms 135593987 } anMmeTrapAlarmMmeSigtran1303 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The peer process is blocked." -- REPAIR-ACTION -- "No immediate action required. Verify the health of the remote equipment -- and the health of the SS7/IP network." -- ENTITY-TYPE -- "mme-g-peer" -- ::= { anMmeTrapAlarms 135593988 } anMmeTrapAlarmMmeSigtran1304 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The peer process is congested." -- REPAIR-ACTION -- "Address engineering considerations on the remote destination." -- ENTITY-TYPE -- "mme-g-peer" -- ::= { anMmeTrapAlarms 135593989 } anMmeTrapAlarmMmeSigtran1305 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The destination is in unroutable state." -- REPAIR-ACTION -- ""Check the details of the peer process components from CLI 'show epc interface -- ss7 peer ...' to help identify the source of the fault." Check the remote -- destination." -- ENTITY-TYPE -- "mme-remote-destination" -- ::= { anMmeTrapAlarms 135593990 } anMmeTrapAlarmMmeSigtran1306 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The destination is restricted." -- REPAIR-ACTION -- "The operator must return the destination node to service to clear this -- alarm." -- ENTITY-TYPE -- "mme-remote-destination" -- ::= { anMmeTrapAlarms 135593991 } anMmeTrapAlarmMmeSigtran1307 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The destination is congested." -- REPAIR-ACTION -- "If traffic rates are within normal operating limits and all subsystems -- are available, then the processing capacity of the destination has likely -- been over-estimated. The resolution is to address engineering considerations -- on the remote destination." -- ENTITY-TYPE -- "mme-remote-destination" -- ::= { anMmeTrapAlarms 135593992 } anMmeTrapAlarmMmeSigtran1308 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The remote subsystem is unavailable" -- REPAIR-ACTION -- "Check the status of the remote subsystem with the command 'show epc interface -- ss7 remote-subsystem ...'. Alternate paths to the subsystem may be possible, -- analyze the provisioned network configuration and add appropriate entries. -- Also check the remote node and verify the state it is reporting for its -- subsystem." -- ENTITY-TYPE -- "mme-remote-destination" -- ::= { anMmeTrapAlarms 135593993 } anMmeTrapAlarmMmeSigtran1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 135594083 } anMmeTrapAlarmMmeTcap1303 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "TCAP is unable to bind to the SGSN MAP subsystem." -- REPAIR-ACTION -- "Contact product support organization." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 135659521 } anMmeTrapAlarmMmeTcap1304 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Number of MAP transactions exceeds 95% of provisioned data." -- REPAIR-ACTION -- "Contact product support organization." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 135659522 } anMmeTrapAlarmMmeTcap1305 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "TCAP is unable to bind to the SGSN CAP subsystem." -- REPAIR-ACTION -- "Verify that the configurable attribute 'tcap-max-cap-transactions' value -- for the SGSN CAP is set to a value greater than zero." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 135659523 } anMmeTrapAlarmMmeTcap1306 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Number of CAP transactions exceeds 95% of the configured data." -- REPAIR-ACTION -- "Verify that the configurable attribute 'tcap-max-cap-transactions' value -- is provisioned to an adequate size." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 135659524 } anMmeTrapAlarmMmeTcap1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 135659619 } anMmeTrapAlarmSgsnIu1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Mapping table has reached the predefined usage thresholds." -- REPAIR-ACTION -- "Compare the values of counter SCCP.CurrentNbrOpenConnections under "statistics -- iu sccp", versus the configured value under "epc interface iu rnc max-iu-connections". -- If the value of the counter is much higher than the configured limit, -- it may indicate that the mapping table has stale connections, and a CALLP -- VM switchover may help. Switchover can be performed on the affected compute -- node to rejected-connections." -- ENTITY-TYPE -- "mme-rnc" -- ::= { anMmeTrapAlarms 136314881 } anMmeTrapAlarmSgsnIu1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "SCCP connection resource pool reaches predefined usage thresholds." -- REPAIR-ACTION -- "Determine why so many connections are being used or requested by the RNCs. -- RNCs may need to be re-engineered to reduce the number of SCCP connection -- requests, especially when the alarms have persisted for a long time during -- high traffic period." -- ENTITY-TYPE -- "mme-rnc" -- ::= { anMmeTrapAlarms 136314882 } anMmeTrapAlarmSgsnIu1303 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Failure to register with the available M3uaAsp instance(s)." -- REPAIR-ACTION -- "Verify that the "epc interface iu rnc destination-point-code" is unique -- for each SCCP. Also check if any configured "epc interface iu ipsp-instance" -- are able to send registration acknowledgements to the RNC." -- ENTITY-TYPE -- "mme-rnc" -- ::= { anMmeTrapAlarms 136314883 } anMmeTrapAlarmSgsnIu1304 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "RNC connection state." -- REPAIR-ACTION -- "Verify that the all peers connected to RNC are up. If RNC has backup RNC -- configured check the state of peers connected to backup RNC also." -- ENTITY-TYPE -- "mme-rnc" -- ::= { anMmeTrapAlarms 136314884 } anMmeTrapAlarmSgsnIu1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 136314979 } anMmeTrapAlarmSgsnIpSp1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Failure to communicate with the IP-RNC." -- REPAIR-ACTION -- "If this alarm persists after startup, check the configuration of 'epc interface -- iu m3ua' and 'epc interface iu dest-peer-map' to confirm addressing and -- naming, and check the health of the network." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 136380417 } anMmeTrapAlarmSgsnIpSp1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The peer process is unavailable for routing purposes." -- REPAIR-ACTION -- "If this alarm persists after startup, check the status of the destination -- represented by this iu peer component." -- ENTITY-TYPE -- "mme-iu-peer" -- ::= { anMmeTrapAlarms 136380418 } anMmeTrapAlarmSgsnIpSp1302 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The peer process is congested." -- REPAIR-ACTION -- "The resolution is to address engineering considerations on the remote destination." -- ENTITY-TYPE -- "mme-iu-peer" -- ::= { anMmeTrapAlarms 136380419 } anMmeTrapAlarmSgsnIpSp1303 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The destination is in unroutable state." -- REPAIR-ACTION -- "If this alarm persists after startup, check the details of the 'epc interface -- iu peer' components that correspond to this destination. Information in -- these iu peer components will identify the source of the fault. Check the -- remote destination." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 136380420 } anMmeTrapAlarmSgsnIpSp1304 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The destination is restricted." -- REPAIR-ACTION -- "The operator must return the destination node to service to clear this -- alarm." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 136380421 } anMmeTrapAlarmSgsnIpSp1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 136380515 } anMmeTrapAlarmSgsnSd1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The maximum allocated LLEs has been reached." -- REPAIR-ACTION -- "Verify that the values of the provisionable attribute 'lle-to-mobile-ratio' -- under 'epc engineering sd-engineering' component are sufficient to handle -- the level of subscriber demand required. Increase if necessary." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 136445953 } anMmeTrapAlarmSgsnSd1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The maximum allocated LLC-ABM data entities has been reached." -- REPAIR-ACTION -- "Verify that the value of the provisionable attribute 'abm-mode-lle-to-mobile-ratio' -- under 'epc interface gb llc' component is sufficient to handle the level -- of subscriber demand required. Increase if necessary." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 136445954 } anMmeTrapAlarmSgsnSd1302 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The maximum allocated session entities has been reached." -- REPAIR-ACTION -- "Verify that the values of the provisionable attribute 'pdn-average' under -- 'epc engineering sc-capacity' component are sufficient to handle the level -- of subscriber demand required. Increase if necessary." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 136445955 } anMmeTrapAlarmSgsnSd1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 136446051 } anMmeTrapAlarmSgsnGb1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The number of unavailable PTP-BVCs has exceeded the threshold." -- REPAIR-ACTION -- "Perform a manual PTP-BVC audit on the NSE shown in the alarm on both the -- SGSN and PCU. Verify that PTP-BVC configuration is consistent with the -- PCU, and verify that the threshold and timer provisionable attributes are -- set properly. Additionally, a signaling BVC reset procedure ('epc interface -- gb sig-bvc reset ...') can be performed, which will result in a service -- outage for the impacted NSE." -- ENTITY-TYPE -- "mme-nse" -- ::= { anMmeTrapAlarms 136511489 } anMmeTrapAlarmSgsnGb1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "No PTP-BVCs were created after a signaling BVC reset procedure." -- REPAIR-ACTION -- "This alarm is informational in nature. No remedial action is necessary -- on the SGSN, corrective action must take place at the PCU. Verify the health -- of the network path to the PCU. Verify that the PCU is functioning properly." -- ENTITY-TYPE -- "mme-nse" -- ::= { anMmeTrapAlarms 136511490 } anMmeTrapAlarmSgsnGb1302 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The number of unavailable data NS-VCs on an NSE crossed a threshold." -- REPAIR-ACTION -- "Check the data NS-VCs for the NSE specified in the alarm and try to resolve -- any issues with those in unavailable states." -- ENTITY-TYPE -- "mme-nse" -- ::= { anMmeTrapAlarms 136511491 } anMmeTrapAlarmSgsnGb1303 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The number of unavailable signaling NS-VCs on an NSE crossed a threshold." -- REPAIR-ACTION -- "Check the signaling NS-VCs for the NSE specified in the alarm and try to -- resolve any issues with those in unavailable states." -- ENTITY-TYPE -- "mme-nse" -- ::= { anMmeTrapAlarms 136511492 } anMmeTrapAlarmSgsnGb1304 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "There are problems with the dynamic IP configuration procedure." -- REPAIR-ACTION -- "Verify the health of the network path to the PCU. Verify that the PCU is -- functioning properly." -- ENTITY-TYPE -- "mme-nse" -- ::= { anMmeTrapAlarms 136511493 } anMmeTrapAlarmSgsnGb1305 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "NSE process creation failed." -- REPAIR-ACTION -- "Check the health of the 'blade/vm' supporting this callP VM (as identified -- in the ref-entity-tag of the alarm)." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 136511494 } anMmeTrapAlarmSgsnGb1306 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The number of unavailable NS-VCs on an NSE crossed a threshold." -- REPAIR-ACTION -- "Check the NS-VCs for the NSE specified in the alarm and try to resolve -- any issues with those in unavailable states." -- ENTITY-TYPE -- "mme-nse" -- ::= { anMmeTrapAlarms 136511495 } anMmeTrapAlarmSgsnGb1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 136511587 } anMmeTrapAlarmCsl1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The maximum records for a CSL file has been exceeded." -- REPAIR-ACTION -- "Adjust the configuration under "epc csl profile" to either increase the -- max-records-per-file limit, or decrease the number of triggers or events -- enabled." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 136642561 } anMmeTrapAlarmCsl1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The CSL file system partition is full." -- REPAIR-ACTION -- "Consider changing the parition size." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 136642562 } anMmeTrapAlarmCsl1302 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected." -- REPAIR-ACTION -- "Contact your next level of support. Consider switching over to the standby -- callP VM and then locking and unlocking the former active, now standby, -- callP VM." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 136642563 } anMmeTrapAlarmCsl1303 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The remote CSL server is unreachable or misconfigured." -- REPAIR-ACTION -- "Check that the remote CSL server(s) and network is operational." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 136642564 } anMmeTrapAlarmCsl1304 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected in the CSL client process." -- REPAIR-ACTION -- "Contact your next level of support. Consider switching over to the standby -- callP VM and then locking and unlocking the former active, now standby, -- callP VM." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 136642565 } anMmeTrapAlarmCsl1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 136642659 } anMmeTrapAlarmMmeSbc1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "No connection to the CBC Server." -- REPAIR-ACTION -- "Verify health of the CBC and the IP network." -- ENTITY-TYPE -- "mme-sbc-if" -- ::= { anMmeTrapAlarms 137232385 } anMmeTrapAlarmMmeSbc1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "MME failed to decode or process the message." -- REPAIR-ACTION -- "Contact your next level of support to resolve the issue. A manual clear -- of the alarm may be required." -- ENTITY-TYPE -- "mme-sbc-cbc" -- ::= { anMmeTrapAlarms 137232386 } anMmeTrapAlarmMmeSbc1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 137232483 } anMmeTrapAlarmDns1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "[obsolete] An external DNS server is unreachable" -- REPAIR-ACTION -- "Verify the health of the remote equipment and the health of the IP network." -- ENTITY-TYPE -- "dns-server" -- ::= { anMmeTrapAlarms 137297921 } anMmeTrapAlarmDns1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected." -- REPAIR-ACTION -- "Contact your next level of support" -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 137297922 } anMmeTrapAlarmDns1302 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "DNS Service Reachability" -- REPAIR-ACTION -- "Check the network connectivity between the MME/SGSN and the DNS servers -- (as configured under epc dns server), and check the health of the DNS servers. -- The MME/SGSN provides resilience against DNS server instability by suspending -- removal of dynamic cache entries with expired TTL when no servers are reachable, -- but for a prolonged outage this can lead to the usage of stale DNS information. -- For a network that relies on remote DNS servers (indirectly or directly) -- for some domains, it may be necessary to adjust the retry timers and retry -- alarm threshold configured under epc dns dns-if. " -- ENTITY-TYPE -- "dns-server" -- ::= { anMmeTrapAlarms 137297923 } anMmeTrapAlarmDns1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 137298019 } anMmeTrapAlarmTrace1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected." -- REPAIR-ACTION -- "Contact your next level of support. Consider switching over to the standby -- callP VM and then locking and unlocking the former active, now standby, -- callP VM. " -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 137494529 } anMmeTrapAlarmTrace1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 137494627 } anMmeTrapAlarmOverload1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The MME is experiencing paging overload." -- REPAIR-ACTION -- "No immediate action required by the operator. The Subscriber Control function -- triggers the configured abatement action." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 138412033 } anMmeTrapAlarmOverload1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Abatement action is being applied to address paging overload." -- REPAIR-ACTION -- "No action required by the operator. The Subscriber Control function will -- take the abatement action described in the alarm." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 138412034 } anMmeTrapAlarmOverload1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 138412131 } anMmeTrapAlarmMmeSgs1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "VLR connection status." -- REPAIR-ACTION -- "Check the configuration of the VLR (show config epc interface sgs) to determine -- if it is multi-home and if there is more than one SCTP association configured. -- Check the status of each connection using the command 'show epc interface -- sgs vlr', and use the alarm text to determine which particular associations -- are down." -- ENTITY-TYPE -- "mme-vlr" -- ::= { anMmeTrapAlarms 138477569 } anMmeTrapAlarmMmeSgs1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected. " -- REPAIR-ACTION -- "Contact product support organization. Consider switching over to the standby -- callP VM and then locking and unlocking the former active, now standby, -- callP VM. " -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 138477570 } anMmeTrapAlarmMmeSgs1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 138477667 } anMmeTrapAlarmMmeAtam1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected." -- REPAIR-ACTION -- "Contact product support organization. Consider switching over to the standby -- callP VM and then locking and unlocking the former active, now standby, -- callP VM." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 138739713 } anMmeTrapAlarmMmeAtam1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 138739811 } anMmeTrapAlarmFgwS1Mme1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "FGW is unable to reach MME over S1-MME (SCTP) interface." -- REPAIR-ACTION -- "Verify that MME is configured correctly. Verify that MME is up and communicating." -- ENTITY-TYPE -- "mme-s1-mme-peer" -- ::= { anMmeTrapAlarms 140771329 } anMmeTrapAlarmFgwS1Mme1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected." -- REPAIR-ACTION -- "Contact your next level of support. Consider switching over to the standby -- callP VM and then locking and unlocking the former active, now standby, -- callP VM." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 140771330 } anMmeTrapAlarmFgwS1Mme1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "No action required by operator." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 140771427 } anMmeTrapAlarmFgwSc1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Connection data is out of synchronization." -- REPAIR-ACTION -- "No immediate action required. The active and standby callP VMs (if available) -- automatically attempt to resynchronize with each other. If condition persists, -- contact your next level of support." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 142344193 } anMmeTrapAlarmFgwSc1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected." -- REPAIR-ACTION -- "Contact your next level of support. Consider switching over to the standby -- callP VM and then locking and unlocking the former active, now standby, -- callP VM." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 142344194 } anMmeTrapAlarmFgwSc1302 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The FGW SC application is experiencing congestion." -- REPAIR-ACTION -- "No immediate action required by the operator. The Subscriber Control function -- triggers the configured abatement action." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 142344195 } anMmeTrapAlarmFgwSc1303 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Abatement action is being applied to address congestion overload." -- REPAIR-ACTION -- "No action required by the operator. The Subscriber Control function is -- taking the abatement action described in the alarm." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 142344196 } anMmeTrapAlarmFgwSc1304 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Attach success rate for FGW has fallen" -- REPAIR-ACTION -- "Examine the fgwFGW.EpsUeConnectIgn connect failure counters and verify -- the health of the network." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 142344197 } anMmeTrapAlarmFgwSc1305 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The number of connections exceeded the configured no. of connections per VM." -- REPAIR-ACTION -- "No immediate action required by the operator. The Subscriber Control function -- triggers abatement action on a per MPU basis when the attached subscriber -- count exceeds the configured threshold." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 142344198 } anMmeTrapAlarmFgwSc1306 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Abatement action is being applied to address subscriber overload." -- REPAIR-ACTION -- "No action required by the operator. The Subscriber Control function is -- taking the abatement action described in the alarm." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 142344199 } anMmeTrapAlarmFgwSc1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "No action required by operator." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 142344291 } anMmeTrapAlarmFgwS1Enb1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected." -- REPAIR-ACTION -- "Contact your next level of support. If only one proccess is reporting this -- alarm do nothing else. If several processes have raised this alarm consider -- locking and unlocking the callP VM." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 142409729 } anMmeTrapAlarmFgwS1Enb1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "No action required by operator." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 142409827 } anMmeTrapAlarmFgwS1Server1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "ENodeB process creation failed." -- REPAIR-ACTION -- "Check the health of the 'blade/vm' supporting this callP VM (as identified -- in the ref-entity-tag of the alarm)." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 142475265 } anMmeTrapAlarmFgwS1Server1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected." -- REPAIR-ACTION -- "Contact your next level of support. Consider switching over to the standby -- callP VM and then locking and unlocking the former active, now standby, -- callP VM." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 142475266 } anMmeTrapAlarmFgwS1Server1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 142475363 } anMmeTrapAlarmMmeSls1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Failure of SCTP connection to E-SMLC." -- REPAIR-ACTION -- "Check if the IP address of the 'e-smlc' entity is configured properly -- and check if the E-SMLC is down." -- ENTITY-TYPE -- "mme-e-smlc" -- ::= { anMmeTrapAlarms 143392769 } anMmeTrapAlarmMmeSls1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected." -- REPAIR-ACTION -- "Contact product support organization. Consider switching over to the standby -- callP VM and then locking and unlocking the former active, now standby, -- callP VM." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 143392770 } anMmeTrapAlarmMmeSls1302 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Current transactions for this E-SMLC exceeds 90% of the configured data." -- REPAIR-ACTION -- "Verify that the 'max-transactions-per-peer' configured under 'epc interface -- sls sls-if' is set to a proper value and the number of E-SMLCs per mmeSls -- service group is set to a proper value." -- ENTITY-TYPE -- "mme-e-smlc" -- ::= { anMmeTrapAlarms 143392771 } anMmeTrapAlarmMmeSls1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 143392867 } anMmeTrapAlarmPathMon1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "Alarm is raised when virtual machine Ethernet interface is failed." -- REPAIR-ACTION -- "Check source of alarm." -- ENTITY-TYPE -- "srm-eth" -- ::= { anMmeTrapAlarms 143917057 } anMmeTrapAlarmPathMon1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A network connectivity outage has been detected by the BFD protocol." -- REPAIR-ACTION -- "Verify that the Next-Hop router is in-service. Verify network connectivity -- between this VM and the remote Next-Hop router.Verify that the Next-Hop -- router has not administratively removed itself from service via the BFD -- protocol." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 143917058 } anMmeTrapAlarmPathMon1302 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A network connectivity outage has been detected by the BFD protocol." -- REPAIR-ACTION -- "Verify that at least one Load Balancer instance is in-service. Verify network -- connectivity between this VM and the Load Balancer VMs." -- ENTITY-TYPE -- "srm-eth" -- ::= { anMmeTrapAlarms 143917059 } anMmeTrapAlarmPathMon1303 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The number of network interfaces in the VM does not match configured interfaces." -- REPAIR-ACTION -- "Correctly configure the network on the node or in the VM." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 143917060 } anMmeTrapAlarmPathMon1304 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The virtual network interface connections do not match configuration." -- REPAIR-ACTION -- "Correctly configure the network. If the next-hop router was not present, -- then manually clear the alarm or reset the VM when next-hop router comes -- online." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 143917061 } anMmeTrapAlarmPathMon1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "srm-eth" -- ::= { anMmeTrapAlarms 143917155 } anMmeTrapAlarmLbCtrl1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected." -- REPAIR-ACTION -- "Contact your next level of support" -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 144113665 } anMmeTrapAlarmLbCtrl1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "No Action required by Operator." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 144113763 } anMmeTrapAlarmEdp1300 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "The maximum allocated PDP context/bearer entities has been reached." -- REPAIR-ACTION -- "" -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 144179201 } anMmeTrapAlarmEdp1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously generated by this application instance are cleared." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 144179299 } anMmeTrapAlarmMmeMbms1301 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "MBMS Bearer Context is out of synchronization." -- REPAIR-ACTION -- "No immediate action required." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 196673537 } anMmeTrapAlarmMmeMbms1302 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "A potential memory leak has been detected." -- REPAIR-ACTION -- "Contract your next level of support." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 196673538 } anMmeTrapAlarmMmeMbms1399 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeFirstEvent, anMmeLastEvent, anMmeLocation, anMmeService, anMmeAlarmIndex } STATUS current DESCRIPTION "All alarms previously gererated by this application instance are cleared." -- REPAIR-ACTION -- "No Action required by Operator" -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapAlarms 196673635 } anMmeTrapEventNm1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "VM administrative state change" -- REPAIR-ACTION -- "None" -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 65536100 } anMmeTrapEventNm1401 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "VM switchover completed" -- REPAIR-ACTION -- "None" -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 65536101 } anMmeTrapEventLi1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "LI Reject Pending Switchover." -- REPAIR-ACTION -- "Try the command again later, or use a "force" option if the resulting data -- loss is acceptable. Synchronization status can be shown using the CLI -- command "show vm"." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 133759076 } anMmeTrapEventLi1401 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "LI Activation During Sync Lost." -- REPAIR-ACTION -- "No repair action required." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 133759077 } anMmeTrapEventLi1402 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "LI Login Failure" -- REPAIR-ACTION -- "See /var/log/auth.log to get more details about the login failure." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 133759078 } anMmeTrapEventMmeRm1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "RM Reject Pending Switchover." -- REPAIR-ACTION -- "Try the command again later, or use a "force" option if the resulting data -- loss is acceptable. Synchronization status can be shown using the CLI command -- "show vm"." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 133824612 } anMmeTrapEventMmeRm1401 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "RM Activation During Sync Lost." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 133824613 } anMmeTrapEventMmeS1M1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "S1Master Reject Pending Switchover" -- REPAIR-ACTION -- "Try the command again later, or use a "force" option if the resulting data -- loss is acceptable. Synchronization status can be shown using the CLI -- command "show vm."" -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 133890148 } anMmeTrapEventMmeS1M1401 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "S1Master Activation During Sync Lost." -- REPAIR-ACTION -- "None" -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 133890149 } anMmeTrapEventMmeS1M1402 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "enodeB Connection Rejected." -- REPAIR-ACTION -- "S1 service configuration should be checked. It is possible to increase -- capacity by adjusting the max-enodebs per VM limit configured under s1-capacity, -- or by adding more sig VMs. " -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 133890150 } anMmeTrapEventMmeS1M1403 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "S1 Setup Rejected." -- REPAIR-ACTION -- "S1 service configuration should be checked. It is possible to increase -- capacity by adjusting the max-enodebs per VM limit configured under s1-capacity, -- or by adding more sig VMs." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 133890151 } anMmeTrapEventMmeS1M1404 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Unknown PLMNs" -- REPAIR-ACTION -- "Correct the configuration, either on the MME by adding the 'plmn' entity, -- or on the enodeB." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 133890152 } anMmeTrapEventMmeS1M1405 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "enodeB Duplicate ID." -- REPAIR-ACTION -- "Check enodeB configuration in the network. " -- ENTITY-TYPE -- "mme-enodeb" -- ::= { anMmeTrapEvents 133890153 } anMmeTrapEventMmeS1M1406 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Manual eNodeB/MCE relocation" -- REPAIR-ACTION -- "None" -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 133890154 } anMmeTrapEventMmeS1M1407 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "MBMS M3 Setup Rejected" -- REPAIR-ACTION -- "MmeMCE (SIG) service configuration needs to be checked and additional capacity -- may be added by changing mce-capacity configuration or adding additional -- RM callP VM instances." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 133890155 } anMmeTrapEventMmeS1M1408 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "MBMS Duplicate MCE ID" -- REPAIR-ACTION -- "Correct the configuration on the MCE." -- ENTITY-TYPE -- "mce" -- ::= { anMmeTrapEvents 133890156 } anMmeTrapEventMmeS1M1409 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "MCE Connection Rejected" -- REPAIR-ACTION -- "MmeS1 (SIG) service configuration needs to be checked and additional capacity -- may be added by charging s1-capacity configuration or adding additional -- SIG callP VM instances. " -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 133890157 } anMmeTrapEventMmeUpsm1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "A GTP path was rejected due to max number of paths connected being reached." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 133955684 } anMmeTrapEventMmeIlf1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "ILF Reject Pending Switchover." -- REPAIR-ACTION -- "Try the command again later, or use a "force" option if the resulting data -- loss is acceptable. Synchronization status can be shown using the CLI command -- "show vm"." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 134021220 } anMmeTrapEventMmeIlf1401 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "ILF Activation During Sync Lost." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 134021221 } anMmeTrapEventMmeS1Enb1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Received Write-Replace Warning Response." -- REPAIR-ACTION -- "No repair action required if the ENodeB response was successful. Check -- configuration and health of ENodeB if the response indicates failure." -- ENTITY-TYPE -- "mme-enodeb" -- ::= { anMmeTrapEvents 134152292 } anMmeTrapEventMmeS1Enb1401 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "The MME was unable to relay a warning message from CBC to the ENodeB." -- REPAIR-ACTION -- "Check the health of the ENodeBs and the IP network." -- ENTITY-TYPE -- "mme-enodeb" -- ::= { anMmeTrapEvents 134152293 } anMmeTrapEventMmeDc1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "HSS reset." -- REPAIR-ACTION -- "Verify that the HSS is functioning properly." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 134217828 } anMmeTrapEventMmeSc1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Trace Session Started." -- REPAIR-ACTION -- "No repair action required." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 134283364 } anMmeTrapEventMmeSc1401 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Trace Session Stopped." -- REPAIR-ACTION -- "No repair action required." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 134283365 } anMmeTrapEventMmeSc1402 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "SC Reject Pending Switchover." -- REPAIR-ACTION -- "Try the command again later, or use a "force" option if the resulting data -- loss is acceptable. Synchronization status can be shown using the CLI command -- "show vm"." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 134283366 } anMmeTrapEventMmeSc1403 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "SC Activation During Sync Lost." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 134283367 } anMmeTrapEventMmeSc1404 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Trace enodeB Failure Indication" -- REPAIR-ACTION -- "No repair actions required." -- ENTITY-TYPE -- "mme-enodeb" -- ::= { anMmeTrapEvents 134283368 } anMmeTrapEventMmeSc1405 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "A black or grey mobile has been detected." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 134283369 } anMmeTrapEventMmeSc1406 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "SC process received a PDP context from the HLR that contains invalid data." -- REPAIR-ACTION -- "Verify the PDP context provisioning in the HLR for the indicated subscriber. -- In other cases, contact product support organization personnel." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 134283370 } anMmeTrapEventMmeSc1407 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Operator attempts to lock all NRI instances." -- REPAIR-ACTION -- "If nri-bit-length is 6, then at least 2 NRI instances must be unlocked -- in order to avoid a service interruption. If nri-bit-length is 7, then -- at least 4 NRI instances must be unlocked in order to avoid a service interruption. -- If nri-bit-length is 8, then at least 8 NRI instances must be unlocked -- in order to avoid a service interruption. If nri-bit-length is 9, then -- at least 16 NRI instances must be unlocked in order to avoid a service -- interruption. If nri-bit-length is 10, then at least 32 NRI instances must -- be unlocked in order to avoid a service interruption." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 134283371 } anMmeTrapEventMmeSc1408 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Location information of a SLN monitored UE." -- REPAIR-ACTION -- "This log is generated periodically until timer expiration or monitoring -- of the UE ends by means of removing the configuration." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 134283372 } anMmeTrapEventMmeSc1409 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Location Report Failure Indication from eNodeB." -- REPAIR-ACTION -- "No repair actions required." -- ENTITY-TYPE -- "mme-enodeb" -- ::= { anMmeTrapEvents 134283373 } anMmeTrapEventMmeSc1410 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Emergency Call Positioning Failure." -- REPAIR-ACTION -- "Check the availability of E-SMLC and GMLC usingcommands for epc interface -- sls esmlc and epc interface diameter peer respectively." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 134283374 } anMmeTrapEventMmeSc1411 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Directional Offload Failed" -- REPAIR-ACTION -- "Check the target-mme-ip-address/target-sgsn-ip-address and the target node -- to see if directional offload is supported" -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 134283375 } anMmeTrapEventMmeSc1412 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Subscriber move successful" -- REPAIR-ACTION -- "None" -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 134283376 } anMmeTrapEventMmeSc1413 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "VLR Reset (Gs type)." -- REPAIR-ACTION -- "Verify that the VLR is functioning properly. Reset indication from Gs VLR -- does not trigger any active recovery action on the SGSN." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 134283377 } anMmeTrapEventMmeUpm1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "GW restart counter increment detected. " -- REPAIR-ACTION -- "Verify that GW is working properly." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 134545508 } anMmeTrapEventMmeSigtran1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Sigtran Unauthorized Associate" -- REPAIR-ACTION -- "Most likely, this customer log will indicate a provisioning error. Check -- for mismatches between the IP address and port in the customer log and -- those in peer process components. However, in the case of an unsecure or -- public network, this customer log indicates that an intrusion has been -- successfully defeated. No further action is required." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 135594085 } anMmeTrapEventMmeSigtran1401 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Sigtran Unknown Destination" -- REPAIR-ACTION -- "Use point code in the customer log to diagnose misconfiguration." -- ENTITY-TYPE -- "mme-remote-destination" -- ::= { anMmeTrapEvents 135594086 } anMmeTrapEventMmeTcap1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "HLR Reset Received" -- REPAIR-ACTION -- "Verify that the HLR is functioning properly." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 135659621 } anMmeTrapEventSgsnIu1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "IU Reject Pending Switchover." -- REPAIR-ACTION -- "Try the command again later, or use a "force" option if the resulting data -- loss is acceptable. Synchronization status can be shown using the CLI command -- "show vm"." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 136314980 } anMmeTrapEventSgsnIu1401 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Iu Global CN-ID Mismatch." -- REPAIR-ACTION -- "Check RNC configuration or configure the 'epc service-area sgsn-pool cn-id' -- on the SGSN." -- ENTITY-TYPE -- "mme-rnc" -- ::= { anMmeTrapEvents 136314981 } anMmeTrapEventSgsnIpSp1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Stale SCCP Entry found on IpSp." -- REPAIR-ACTION -- "No action required." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 136380516 } anMmeTrapEventSgsnIpSp1401 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "M3UA association from unauthorized IP address and port has failed." -- REPAIR-ACTION -- "No action required." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 136380517 } anMmeTrapEventSgsnSd1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Data buffer memory on SD process reached a threshold level." -- REPAIR-ACTION -- "No repair action required." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 136446052 } anMmeTrapEventSgsnSd1401 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Downlink buffer initialization failed." -- REPAIR-ACTION -- "No repair action required." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 136446053 } anMmeTrapEventSgsnSd1402 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Memory pool usage reached a threshold (allocating header compression obj)." -- REPAIR-ACTION -- "Increase the provisioned value of 'max-header-compression-entities' attribute -- of the 'epc interface gb sndcp' component." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 136446054 } anMmeTrapEventSgsnSd1403 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Number of allocated PFC leaky buckets reaches the calculated limit." -- REPAIR-ACTION -- "Verify that the values of the provisionable attributes 'average-pfcs-per-mobile' -- under 'epc interface gb packet-flow-management' component and 'pdn-average' -- under 'epc engineering sc-capacity' component are sufficient to handle -- the level of subscriber demand required. Increase if necessary." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 136446055 } anMmeTrapEventSgsnSd1404 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Maximum number of BVCs is reached." -- REPAIR-ACTION -- "Perform a manual BVC audit across all NSEs and determine which BVC(s) exceed -- SGSN engineering limits and remove them from service at the PCU. " -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 136446056 } anMmeTrapEventSgsnGb1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "A signaling BVC reset has occurred." -- REPAIR-ACTION -- "This log is informational in nature. No remedial action is necessary." -- ENTITY-TYPE -- "mme-nse" -- ::= { anMmeTrapEvents 136511588 } anMmeTrapEventSgsnGb1401 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "The limit of PTP-BVCs per NSE has been reached." -- REPAIR-ACTION -- "Perform a manual PTP-BVC audit across all NSEs and determine which PTP-BVCs -- exceed SGSN engineering limits and remove them from service at the PCU." -- ENTITY-TYPE -- "mme-nse" -- ::= { anMmeTrapEvents 136511589 } anMmeTrapEventSgsnGb1402 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Signaling NS-VCs are unavailable." -- REPAIR-ACTION -- "Verify the health of the network path to the PCU. Verify that the PCU is -- functioning properly." -- ENTITY-TYPE -- "mme-nse" -- ::= { anMmeTrapEvents 136511590 } anMmeTrapEventSgsnGb1403 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "There are temporary problems with the dynamic IP configuration procedure." -- REPAIR-ACTION -- "This log is informational in nature. No remedial action is necessary" -- ENTITY-TYPE -- "mme-nse" -- ::= { anMmeTrapEvents 136511591 } anMmeTrapEventSgsnGb1404 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "A dynamic config procedure was attempted with static config provisioned." -- REPAIR-ACTION -- "Verify that the PCU is using a static configuration or reconfigure the -- NSE on the SGSN to use a dynamic configuration; i.e., delete all configured -- remote endpoints ('epc interface gb static-nse-remote-endpoint' instances)." -- ENTITY-TYPE -- "mme-nse" -- ::= { anMmeTrapEvents 136511592 } anMmeTrapEventSgsnGb1405 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "There is a potential PTP-BVC mismatch." -- REPAIR-ACTION -- "Perform a manual PTP-BVC audit on the NSE shown in the log on both the -- SGSN and PCU. Verify that PTP-BVC state mismatches exist and take appropriate -- action on the PCU to unblock any PTP-BVCs with mismatched states. Additionally, -- a signaling BVC reset procedure ('epc interface gb sig-bvc reset ...') -- can be performed, which will result in a service outage for the impacted -- NSE." -- ENTITY-TYPE -- "mme-nse" -- ::= { anMmeTrapEvents 136511593 } anMmeTrapEventMmeSbc1401 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "A message is either received from the CBC or sent to the CBC." -- REPAIR-ACTION -- "No repair action required." -- ENTITY-TYPE -- "cbc" -- ::= { anMmeTrapEvents 137232485 } anMmeTrapEventMmeSbc1402 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "CBC Association Status" -- REPAIR-ACTION -- "Check health of CBC and IP network" -- ENTITY-TYPE -- "cbc" -- ::= { anMmeTrapEvents 137232486 } anMmeTrapEventTrace1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "A 3GPP trace file was closed successfully and is available." -- REPAIR-ACTION -- "No repair action required." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 137494628 } anMmeTrapEventTrace1401 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "The file system partition used for PCAP filtering is full." -- REPAIR-ACTION -- "No immediate repair action required." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 137494629 } anMmeTrapEventTrace1402 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Trace File Bulk Sync Abnormal Termination." -- REPAIR-ACTION -- "It is recommended to audit the trace files in /usr/local/epc/trace on both -- active and standby MGMT/MRM VM for consistency, to ensure there is no loss -- of data due to possible abnormal file sync termination." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 137494630 } anMmeTrapEventMmeSgs1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Location Area can not be determined." -- REPAIR-ACTION -- "Configure the TA in the 'tac-range-list' attribute of the 'location-area' -- entity or designate a default LA by setting the 'default-la' attribute -- to "true" for one of the location-area entities." -- ENTITY-TYPE -- "mme-tracking-area" -- ::= { anMmeTrapEvents 138477668 } anMmeTrapEventMmeSgs1401 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "VLR Reset." -- REPAIR-ACTION -- "Verify that the VLR is functioning properly." -- ENTITY-TYPE -- "mme-vlr" -- ::= { anMmeTrapEvents 138477669 } anMmeTrapEventMME1600 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Hung process detected." -- REPAIR-ACTION -- "No repair action required." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 140640356 } anMmeTrapEventMME1601 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Critical config change received, process restarted." -- REPAIR-ACTION -- "No repair action required." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 140640357 } anMmeTrapEventMME1602 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Backup Created." -- REPAIR-ACTION -- "No repair action required." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 140640358 } anMmeTrapEventMME1603 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Support File Created." -- REPAIR-ACTION -- "No repair action required." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 140640359 } anMmeTrapEventMME1604 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Login Failure" -- REPAIR-ACTION -- "See /var/log/auth.log to get more details about the login failure." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 140640360 } anMmeTrapEventFgwSc1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Trace Session Started." -- REPAIR-ACTION -- "No repair action required." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 142344292 } anMmeTrapEventFgwSc1401 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Trace Session Stopped." -- REPAIR-ACTION -- "No repair action required." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 142344293 } anMmeTrapEventFgwSc1402 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "FGW SC Reject Pending Switchover." -- REPAIR-ACTION -- "Try the command again later, or use a "force" option if the resulting data -- loss is acceptable. Synchronization status can be shown using the CLI -- command "show fgw status system"." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 142344294 } anMmeTrapEventFgwSc1403 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "SC Activation During Sync Lost." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 142344295 } anMmeTrapEventFgwSc1404 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Trace eNodeB Failure Indication." -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "mme-enodeb" -- ::= { anMmeTrapEvents 142344296 } anMmeTrapEventLbCtrl1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "VM Steering Registration Failure." -- REPAIR-ACTION -- "Note the VM type and IP addresses in the reason text and lock/unlock the -- reporting LB VM." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 144113764 } anMmeTrapEventLbCtrl1401 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Steering Policy Add Failure." -- REPAIR-ACTION -- "Analyze the policy 5 tuple and target VM name in the reason text and contact -- your next level of support." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 144113765 } anMmeTrapEventLbCtrl1402 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Steering Policy Redirect Failure." -- REPAIR-ACTION -- "Analyze the policy 5 tuple and target VM name in the reason text and contact -- your next level of support." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 144113766 } anMmeTrapEventLbCtrl1403 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Steering Policy Delete Failure." -- REPAIR-ACTION -- "Analyze the policy id in the reason text and contact your next level of -- support." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 144113767 } anMmeTrapEventEdp1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "Data buffer memory on EDP process reached a threshold level." -- REPAIR-ACTION -- "No repair action required." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 144179300 } anMmeTrapEventMmeMbms1400 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "MBMS Reject Pending Swtichover" -- REPAIR-ACTION -- "Try the command again later, or use a "force" option if the resulting data -- loss is acceptable. Synchronization status can be shown using the CLI command -- "show vm"." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 196673636 } anMmeTrapEventMmeMbms1401 NOTIFICATION-TYPE OBJECTS { anMmeAlarmState, anMmeAlarmSeverity, anMmeEntityTag, anMmeSubentityInfo, anMmeLocationGateway, anMmeReason, anMmeAlarmDateAndTime, anMmeGroupKey, anMmeSequenceNumber, anMmeLocation, anMmeService } STATUS current DESCRIPTION "MBMS Activation During Sync Lost" -- REPAIR-ACTION -- "None." -- ENTITY-TYPE -- "system" -- ::= { anMmeTrapEvents 196673637 } END