-- **************************************************************************** -- **************************************************************************** -- Copyright(c) 2004 Mediatrix Telecom, Inc. -- NOTICE: -- This document contains information that is confidential and proprietary -- to Mediatrix Telecom, Inc. -- Mediatrix Telecom, Inc. reserves all rights to this document as well as -- to the Intellectual Property of the document and the technology and -- know-how that it includes and represents. -- This publication cannot be reproduced, neither in whole nor in part in -- any form whatsoever without written prior approval by -- Mediatrix Telecom, Inc. -- Mediatrix Telecom, Inc. reserves the right to revise this publication -- and make changes at any time and without the obligation to notify any -- person and/or entity of such revisions and/or changes. -- **************************************************************************** -- **************************************************************************** MX-R2-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, Integer32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF MxEnableState, MxActivationState, MxIpHostName, MxIpAddress, MxIpPort, MxAdvancedIpPort, MxIpSubnetMask, MxDigitMap FROM MX-TC MxUInt64, MxFloat32, MxIpHostNamePort, MxIpAddr, MxIpAddrPort, MxIpAddrMask, MxUri, MxUrl FROM MX-TC2 mediatrixServices FROM MX-SMI2; r2MIB MODULE-IDENTITY LAST-UPDATED "1910210000Z" ORGANIZATION " Mediatrix Telecom, Inc. " CONTACT-INFO " Mediatrix Telecom, Inc. 4229, Garlock Street Sherbrooke (Quebec) Canada Phone: (819) 829-8749 " DESCRIPTION " R2 Channel Associated Signaling The R2 Channel Associated Signaling (R2) service manages the E1 CAS telephony interfaces. " ::= { mediatrixServices 1875 } r2MIBObjects OBJECT IDENTIFIER ::= { r2MIB 1 } -- **************************************************************************** -- Group:R2 Configuration -- **************************************************************************** r2Group OBJECT IDENTIFIER ::= { r2MIBObjects 100 } -- *************************************************************************** -- Table:R2 Channel Associated Signaling (R2 CAS) -- *************************************************************************** r2Table OBJECT-TYPE SYNTAX SEQUENCE OF R2Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION " R2 Channel Associated Signaling (R2 CAS) Configuration parameters related to the R2 channel associated signaling (R2 CAS) on this managed device. " ::= { r2Group 100 } r2Entry OBJECT-TYPE SYNTAX R2Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A row in table R2 Channel Associated Signaling (R2 CAS). " INDEX { r2Name } ::= { r2Table 1 } R2Entry ::= SEQUENCE { r2Name OCTET STRING, r2ChannelRange OCTET STRING, r2ChannelAllocationStrategy INTEGER, r2MaxActiveCalls Unsigned32, r2EncodingScheme INTEGER, r2LineSignaling INTEGER, r2IncomingDigitSignaling INTEGER, r2OutgoingDigitSignaling INTEGER, r2CountrySelection INTEGER, r2DigitAttenuation Unsigned32 } -- Index:Name r2Name OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " Name Name that identifies the interface. " ::= { r2Entry 100 } -- Columnar:Channel Range r2ChannelRange OBJECT-TYPE SYNTAX OCTET STRING ( SIZE(1..10) ) MAX-ACCESS read-write STATUS current DESCRIPTION " Channel Range Defines the range of active bearer channels. " DEFVAL { "1-30" } ::= { r2Entry 200 } -- Columnar:Channel Allocation Strategy r2ChannelAllocationStrategy OBJECT-TYPE SYNTAX INTEGER { ascending(100) , descending(200) , roundRobinAscending(300) , roundRobinDescending(400) } MAX-ACCESS read-write STATUS current DESCRIPTION " Channel Allocation Strategy Defines the strategy for selecting bearer channels. Available strategies are: * Ascending: select the lowest-numbered non-busy bearer channel * Descending: select the highest-numbered non-busy bearer channel * RoundRobinAscending: use a cyclic round-robin search; starting from the bearer channel that follows the bearer channel used for the last call, select the lowest-numbered non-busy bearer channel * RoundRobinDescending: use a cyclic round-robin search; starting from the bearer channel that precedes the bearer channel used for the last call, select the highest-numbered non-busy bearer channel " DEFVAL { ascending } ::= { r2Entry 300 } -- Columnar:Maximum Active Calls r2MaxActiveCalls OBJECT-TYPE SYNTAX Unsigned32 ( 0..30 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Maximum Active Calls Defines the maximum number of active calls on the interface. Note: The special value 0 indicates no maximum number of active calls. " DEFVAL { 0 } ::= { r2Entry 400 } -- Columnar:Encoding Scheme r2EncodingScheme OBJECT-TYPE SYNTAX INTEGER { g711alaw(100) , g711ulaw(200) } MAX-ACCESS read-write STATUS current DESCRIPTION " Encoding Scheme Defines the voice encoding scheme in the bearer capabilities.This encoding scheme is used when initiating a call on the R2 side. The supported encoding schemes are G.711 u-Law and G.711 A-Law. " DEFVAL { g711alaw } ::= { r2Entry 500 } -- Columnar:Line Signaling r2LineSignaling OBJECT-TYPE SYNTAX INTEGER { q4212BitsSignaling(100) } MAX-ACCESS read-write STATUS current DESCRIPTION " Line Signaling Defines the protocol to use for the line signaling: * Q421-2BitsSignaling: R2 line signaling type ITU-U Q.421. Typically used for PCM systems. This signaling protocol must match the one used by the connected equipment or network. " DEFVAL { q4212BitsSignaling } ::= { r2Entry 600 } -- Columnar:Incoming Digit Signaling r2IncomingDigitSignaling OBJECT-TYPE SYNTAX INTEGER { mfcR2(100) , dtmfR2(200) } MAX-ACCESS read-write STATUS current DESCRIPTION " Incoming Digit Signaling Defines the R2 incoming digit signaling method. * MfcR2: Multi Frequency Compelled - R2. * DtmfR2: Dual Tone Multi Frequency - R2. Digit signaling is also known as Address Signaling, Selection Signals, and Register Signaling. The digits are used primarily to indicate the called number, but can also have other meanings, as documented in the ITU-T Q.441 specification. " DEFVAL { mfcR2 } ::= { r2Entry 750 } -- Columnar:Outgoing Digit Signaling r2OutgoingDigitSignaling OBJECT-TYPE SYNTAX INTEGER { mfcR2(100) , dtmfR2(200) } MAX-ACCESS read-write STATUS current DESCRIPTION " Outgoing Digit Signaling Defines the R2 outgoing digit signaling method. * MfcR2: Multi Frequency Compelled - R2. * DtmfR2: Dual Tone Multi Frequency - R2. Digit signaling is also known as Address Signaling, Selection Signals, and Register Signaling. The digits are used primarily to indicate the called number, but can also have other meanings, as documented in the ITU-T Q.441 specification. " DEFVAL { mfcR2 } ::= { r2Entry 760 } -- Columnar:Country Selection r2CountrySelection OBJECT-TYPE SYNTAX INTEGER { brazilR2(100) , mexicoR2(200) , argentinaR2(300) , saudiArabiaR2(400) , venezuelaR2(500) , philippinesR2(600) , iTUTR2(700) } MAX-ACCESS read-write STATUS current DESCRIPTION " Country Selection Identifies the country. * Brazil-R2: Brazil R2 setting. * Mexico-R2: Mexico R2 setting. * Argentina-R2: Argentina R2 setting. * SaudiArabia-R2: SaudiArabia R2 setting. * Venezuela-R2: Venezuela R2 setting. * Philippines-R2: Philippines R2 setting. * ITU-T-R2: ITU-T R2 setting. " DEFVAL { brazilR2 } ::= { r2Entry 800 } -- Columnar:Digit Attenuation r2DigitAttenuation OBJECT-TYPE SYNTAX Unsigned32 ( 0..20 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Digit Attenuation Additional attenuation in dB for MFR2/DTMF digit generation. By default, MFR2/DTMF digit generation power is determined by country selection. This parameter provides a mean to reduce this power. " DEFVAL { 0 } ::= { r2Entry 900 } -- End of table:R2 Channel Associated Signaling (R2 CAS) -- *************************************************************************** -- Table:R2 Signaling Variants -- *************************************************************************** r2SignalingVariantsTable OBJECT-TYPE SYNTAX SEQUENCE OF R2SignalingVariantsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " R2 Signaling Variants This table allows to override or retrieve the default country settings for R2 signaling parameters. This table is effective only if the OverrideDefault parameter is Enabled. If the OverrideDefault parameter is Disabled, any change in this table have no effects. " ::= { r2Group 200 } r2SignalingVariantsEntry OBJECT-TYPE SYNTAX R2SignalingVariantsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A row in table R2 Signaling Variants. " INDEX { r2SignalingVariantsInterfaceName } ::= { r2SignalingVariantsTable 1 } R2SignalingVariantsEntry ::= SEQUENCE { r2SignalingVariantsInterfaceName OCTET STRING, r2SignalingVariantsOverrideDefault MxEnableState, r2SignalingVariantsBitsCD Integer32, r2SignalingVariantsDnisLength Unsigned32, r2SignalingVariantsAniLength Unsigned32, r2SignalingVariantsAniRequestEnable MxEnableState, r2SignalingVariantsSendAniRequestAfterDnisDigits Unsigned32, r2SignalingVariantsCollectCallBlocked MxEnableState, r2SignalingVariantsAniCategory INTEGER, r2SignalingVariantsLineFreeCategory INTEGER, r2SignalingVariantsAniRestrictedEnable MxEnableState, r2SignalingVariantsIncomingDeclineMethod INTEGER, r2SignalingVariantsResetSpecific INTEGER } -- Index:Interface Name r2SignalingVariantsInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " Interface Name Identifies the interface. " ::= { r2SignalingVariantsEntry 100 } -- Row command:Reset Specific r2SignalingVariantsResetSpecific OBJECT-TYPE SYNTAX INTEGER { noOp(0), resetSpecific(10) } MAX-ACCESS read-write STATUS current DESCRIPTION " Reset Specific Resets specific settings of R2 Signaling parameters with the default country settings. This command is used to retrieve the default country configuration set in the CountrySelection parameter. " DEFVAL { noOp } ::= { r2SignalingVariantsEntry 1000 } -- Columnar:Override Default r2SignalingVariantsOverrideDefault OBJECT-TYPE SYNTAX MxEnableState MAX-ACCESS read-write STATUS current DESCRIPTION " Override Default Overrides the default settings of R2 Signaling parameters for the CountrySelection and InterfaceName. * Disable: The interface uses the default country configuration. The configuration set in the current row has no effect on the default country configuration. Refer to the technical documentation to get the default country variants configuration. * Enable: The interface uses the specific country configuration as defined in the current row. To retrieve the default configuration associated with the current country, the parameter reset MUST be enabled. " DEFVAL { disable } ::= { r2SignalingVariantsEntry 300 } -- Columnar:CD Bits r2SignalingVariantsBitsCD OBJECT-TYPE SYNTAX Integer32 ( 0..12 ) MAX-ACCESS read-write STATUS current DESCRIPTION " CD Bits Settings of the C and D bits when the device transmits line signals. C and D bits of received line signals are ignored by the device. " DEFVAL { 1 } ::= { r2SignalingVariantsEntry 400 } -- Columnar:DNIS Length r2SignalingVariantsDnisLength OBJECT-TYPE SYNTAX Unsigned32 ( 0..20 ) MAX-ACCESS read-write STATUS current DESCRIPTION " DNIS Length This parameter specifies the expected length of the DNIS. DNIS (Dialed Number Identification Service) is the called party or the destination number. If a variable length is defined, then the I-15 digit is used to indicate the end of DNIS. * 0: Variable DNIS length used. * 1..20: Number indicates the specific DNIS expected length. " DEFVAL { 0 } ::= { r2SignalingVariantsEntry 500 } -- Columnar:ANI Length r2SignalingVariantsAniLength OBJECT-TYPE SYNTAX Unsigned32 ( 0..20 ) MAX-ACCESS read-write STATUS current DESCRIPTION " ANI Length Defines the length of ANI (Automatic Number Identification) to be requested or sent. If a variable length ANI is used, the tone set in the R2ToneVariants.FwdGroup1EndOfAni parameter is sent to indicate the end of the ANI digits. When fixed length ANI is used and the available ANI digits are longer than the requested length, the last n digits are sent. If available ANI digits are shorter, then the R2ToneVariants.FwdGroup1EndOfAni parameter tone is sent. * 0: Variable ANI length. * 1..20: Specific ANI length. " DEFVAL { 0 } ::= { r2SignalingVariantsEntry 600 } -- Columnar:ANI Request Enable r2SignalingVariantsAniRequestEnable OBJECT-TYPE SYNTAX MxEnableState MAX-ACCESS read-write STATUS current DESCRIPTION " ANI Request Enable Defines whether or not ANI should be requested. ANI (Automatic Number Identification) is the calling party number. When ANI is requested, the calling party category followed by the actual ANI is sent. If this parameter is enabled, the ANI request is sent after the nth DNIS digits (defined in the SendAniRequestAfterDnisDigits parameter) received. " DEFVAL { enable } ::= { r2SignalingVariantsEntry 700 } -- Columnar:Send ANI Request After DNIS Digits r2SignalingVariantsSendAniRequestAfterDnisDigits OBJECT-TYPE SYNTAX Unsigned32 ( 0..10 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Send ANI Request After DNIS Digits When the AniRequestEnable parameter is Enabled, this parameter defines the number of DNIS (Dialed Number Identification Service) digits to be received before sending the ANI request. If a variable number is used, the ANI request is sent after all DNIS digits have been received. * 0: Variable number of DNIS digits. * 1..10: Specific number of DNIS digits. " DEFVAL { 0 } ::= { r2SignalingVariantsEntry 800 } -- Columnar:Collect Call Blocked r2SignalingVariantsCollectCallBlocked OBJECT-TYPE SYNTAX MxEnableState MAX-ACCESS read-write STATUS current DESCRIPTION " Collect Call Blocked Defines if the Collect Call Blockage Option is used. Two methods actually exist to do Collect Call Blockage. The first method refers to R2 signaling and how, through the use of signals, collect calls can be blocked. The second method refers to how, through the use of double answer, the same ends can be achieved. For an incoming collect call, a signal of Group II-8 is sent forward from the caller to the called party. The called party implements the collect call blockage (when the CollectCallBlocked parameter is enabled) by sending backward to the caller a signal of Group B-7 indicating that the collect calls are not being accepted by the called party. Consequently, the originator of the call gets a busy tone and the local calling party circuit that has been used for the call is dropped when the originator puts the phone on hook. The double answer allows the destination side to reject or accept a collect call (toll). Since the owner of the collect call is the person being called, the CO recognizes that the call is being dropped just by the fact that the call was dropped. For regular, non-collect calls, the owner of the call is the person calling and not the party being called. So, if the receiver of the call decides to refuse the call, a double answer is generated within a specified time. If the receiver wants to answer the call, a double answer is not generated and the receiver is then billed for the incoming call. * Enable: The signal of Group B-7 is sent if a Group II-8 (Collect Call) signal is received from the caller or a double answer is generated within a specified time depending on the value defined in the R2TimerVariants table. * Disable: No signal is sent in response to a Group II-8 (Collect Call) signal and/or no double answer is generated by the called side upon incoming calls. " DEFVAL { enable } ::= { r2SignalingVariantsEntry 900 } -- Columnar:Category Group II Signal r2SignalingVariantsAniCategory OBJECT-TYPE SYNTAX INTEGER { natSubscriberNoPrio(100) , natSubscriberPrio(200) , natMaintenance(300) , natSpare(400) , natOperator(500) , natData(600) , intSubscriberNoPrio(700) , intData(800) , intSubscriberPrio(900) , intOperator(1000) , collectCall (1100) } MAX-ACCESS read-write STATUS current DESCRIPTION " Category Group II Signal Specifies the group II forward signal to be sent on receiving a calling party category request. This tone indicates the category of the calling party. * NatSubscriberNoPrio: Call is set up from a national subscriber's line and is not a priority. * NatSubscriberPrio: Call is set up from a national subscriber's line to which priority treatment of calls has been granted. * NatMaintenance: Call comes from a national maintenance equipment. * NatSpare: Spare. * NatOperator: Call is set up from a national operator's position. * NatData: Call will be used for national data transmission. * IntSubscriberNoPrio: Call is set up from an international subscriber's line and is not a priority. * IntData: Call will be used for international data transmission. * IntSubscriberPrio: Call is set up from an international subscriber's line to which priority treatment of calls has been granted. * IntOperator: Call is set up from an international operator's position. * CollectCall: Call is set up for Call Collect. " DEFVAL { natSubscriberNoPrio } ::= { r2SignalingVariantsEntry 920 } -- Columnar:Line Free Group B signal r2SignalingVariantsLineFreeCategory OBJECT-TYPE SYNTAX INTEGER { lineFreeCharge(100) , lineFreeNoCharge(200) } MAX-ACCESS read-write STATUS current DESCRIPTION " Line Free Group B signal Specifies the group B backward signal to be sent by the incoming R2 register to indicate line free condition of the destination party. * LineFreeCharge : Called party's line is free but is to be charged on answer. * LineFreeNoCharge: Called party's line is free but is not to be charged on answer. " DEFVAL { lineFreeCharge } ::= { r2SignalingVariantsEntry 930 } -- Columnar:ANI Restricted Enable r2SignalingVariantsAniRestrictedEnable OBJECT-TYPE SYNTAX MxEnableState MAX-ACCESS read-write STATUS current DESCRIPTION " ANI Restricted Enable This parameter specifies the behaviour of the unit following the reception of a reject request after sending the Send next digit (ANI) request. The request is generally rejected when the calling party is unable to send its identification. * Enable: A congestion tone is sent in response to the reject request and the call should be dropped by the caller. * Disable: The unit uses the same behaviour as the End of ANI Tone and the call continues. " DEFVAL { enable } ::= { r2SignalingVariantsEntry 950 } -- Columnar:Incoming Decline Method r2SignalingVariantsIncomingDeclineMethod OBJECT-TYPE SYNTAX INTEGER { release(100) , clearBack(200) } MAX-ACCESS read-write STATUS current DESCRIPTION " Incoming Decline Method Sets how to cancel a call attempt from R2 if the called party rejects the call when in Seizure Acknowledged state (waiting for answer). * Release: B bit is set to 0 and state is set to Released. * ClearBack: B bit is set to 0 until decline guard expires then B bit is set to 1 and state is set to Clear-back. See also R2TimerVariants.DeclineGuardTimeout parameter. " DEFVAL { release } ::= { r2SignalingVariantsEntry 970 } -- End of table:R2 Signaling Variants -- *************************************************************************** -- Table:R2 Signaling Timer Variants -- *************************************************************************** r2TimerVariantsTable OBJECT-TYPE SYNTAX SEQUENCE OF R2TimerVariantsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " R2 Signaling Timer Variants This table allows to override or retrieve the default country setting for R2 Timers. " ::= { r2Group 300 } r2TimerVariantsEntry OBJECT-TYPE SYNTAX R2TimerVariantsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A row in table R2 Signaling Timer Variants. " INDEX { r2TimerVariantsInterfaceName } ::= { r2TimerVariantsTable 1 } R2TimerVariantsEntry ::= SEQUENCE { r2TimerVariantsInterfaceName OCTET STRING, r2TimerVariantsOverrideDefault MxEnableState, r2TimerVariantsSeizureAckTimeout Integer32, r2TimerVariantsFaultSeizureAckTimeout Integer32, r2TimerVariantsDoubleSeizureTimeout Integer32, r2TimerVariantsDoubleAnswerTimeout Integer32, r2TimerVariantsAnswerTimeout Integer32, r2TimerVariantsReAnswerTimeout Integer32, r2TimerVariantsReleaseGuardTimeout Integer32, r2TimerVariantsInterCallGuardTimeout Integer32, r2TimerVariantsNoDigitTimeout Integer32, r2TimerVariantsCongestionToneGuardTimeout Integer32, r2TimerVariantsUnblockingTimeout Integer32, r2TimerVariantsAddressCompleteTimeout Integer32, r2TimerVariantsWaitAnswerTimeout Integer32, r2TimerVariantsDigitCompleteTimeout Integer32, r2TimerVariantsWaitGroupBResponseCompleteTimeout Integer32, r2TimerVariantsWaitImmediateResponseCompleteTimeout Integer32, r2TimerVariantsPlayToneGuardTimeout Integer32, r2TimerVariantsAcceptCallTimeout Integer32, r2TimerVariantsClearForwardGuardTimeout Integer32, r2TimerVariantsClearBackwardGuardTimeout Integer32, r2TimerVariantsFaultOnAnsweredGuardTimeout Integer32, r2TimerVariantsFaultOnClearBackwardGuardTimeout Integer32, r2TimerVariantsFaultOnSeizeAckGuardTimeout Integer32, r2TimerVariantsFaultOnSeizeGuardTimeout Integer32, r2TimerVariantsDeclineGuardTimeout Integer32, r2TimerVariantsResetSpecific INTEGER } -- Index:Interface Name r2TimerVariantsInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " Interface Name Identifies the interface. " ::= { r2TimerVariantsEntry 100 } -- Columnar:Address Complete Timeout r2TimerVariantsAddressCompleteTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..20000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Address Complete Timeout The Address Complete Timeout is the maximum time that the caller waits for a reception of AddressComplete Tone after sending all ANI or DNIS Digits. This value is expressed in milliseconds (ms). " DEFVAL { 8000 } ::= { r2TimerVariantsEntry 1000 } -- Columnar:Wait Answer Timeout r2TimerVariantsWaitAnswerTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..600000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Wait Answer Timeout The maximal time that the caller waits for an Answer signal (ANSW) after receiving a Group B Line Free Signal Tone. This timer is effective only when the line is free. This value is expressed in milliseconds (ms). " DEFVAL { 60000 } ::= { r2TimerVariantsEntry 1100 } -- Columnar:Digit Complete Timeout r2TimerVariantsDigitCompleteTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..10000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Digit Complete Timeout The maximal time that the caller waits for a Group I forward tone after sending either a Group A next Dnis digit, next Ani digit or next calling category Tone. This value is expressed in milliseconds (ms). " DEFVAL { 4000 } ::= { r2TimerVariantsEntry 1200 } -- Columnar:Wait Group B Response Complete Timeout r2TimerVariantsWaitGroupBResponseCompleteTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..30000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Wait Group B Response Complete Timeout The maximal time that the caller waits for the confirmation of the end of the compelled sequence after receiving a Group B Signal Tone. The end of the compelled sequence is detected by a transition of the backward tone to off. This value is expressed in milliseconds (ms). " DEFVAL { 3000 } ::= { r2TimerVariantsEntry 1300 } -- Columnar:Wait Immediate Response Complete Timeout r2TimerVariantsWaitImmediateResponseCompleteTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..10000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Wait Immediate Response Complete Timeout The maximal time that the caller waits for the confirmation of the end of the compelled sequence after receiving a Group B Signal Tone. The end of the compelled sequence is detected by a transition of the backward tone to off. This timer is specific to the immediate accept Signal Tone. This value is expressed in milliseconds (ms). " DEFVAL { 1000 } ::= { r2TimerVariantsEntry 1400 } -- Columnar:Play Tone guard Timeout r2TimerVariantsPlayToneGuardTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..2000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Play Tone guard Timeout The maximum time an incoming R2 registers waits after receiving the confirmation of the reception of the Group B Signal Tone before playing one of the calling tones in the caller direction. This value is expressed in milliseconds (ms). " DEFVAL { 70 } ::= { r2TimerVariantsEntry 1500 } -- Columnar:Accept Call Timeout r2TimerVariantsAcceptCallTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..10000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Accept Call Timeout Time that the unit waits to accept a R2 CAS call. This value is expressed in milliseconds (ms). " DEFVAL { 2000 } ::= { r2TimerVariantsEntry 1600 } -- Columnar:Clear Forward Guard Timeout r2TimerVariantsClearForwardGuardTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..600000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Clear Forward Guard Timeout The maximum time an outgoing R2 register waits after sending a clear forward line signal before transiting to the idle state. This value is expressed in milliseconds (ms). " DEFVAL { 1500 } ::= { r2TimerVariantsEntry 1700 } -- Columnar:Clear Backward Guard Timeout r2TimerVariantsClearBackwardGuardTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..600000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Clear Backward Guard Timeout The maximum time an incoming R2 register waits after sending a clear backward line signal before sending the idle line signal and transit in the idle state. This value is expressed in milliseconds (ms). " DEFVAL { 1500 } ::= { r2TimerVariantsEntry 1800 } -- Columnar:Fault On Answered Guard Timeout r2TimerVariantsFaultOnAnsweredGuardTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..86400000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Fault On Answered Guard Timeout The maximum time an outgoing R2 register waits for the fault to clear before sending the clear forward line signal. In the case of recognition of bb = 0 while in the answered state, no immediate action is taken. However, the clear forward signal will be sent if bb = 1 is restored or the answered guard timeout is reached. This value is expressed in milliseconds (ms). " DEFVAL { 250 } ::= { r2TimerVariantsEntry 1900 } -- Columnar:Fault On Clear Backward Guard Timeout r2TimerVariantsFaultOnClearBackwardGuardTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..86400000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Fault On Clear Backward Guard Timeout The maximum time an outgoing R2 register waits for the fault to clear before sending the clear forward line signal. In the case of recognition of bb = 0 while in the clear backward state, no immediate action is taken. However, the clear forward signal will be sent if bb = 1 is restored or the clear backward guard timeout is reached. This value is expressed in milliseconds (ms). " DEFVAL { 250 } ::= { r2TimerVariantsEntry 2000 } -- Columnar:Fault On Seize Ack Guard Timeout r2TimerVariantsFaultOnSeizeAckGuardTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..86400000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Fault On Seize Ack Guard Timeout The maximum time an outgoing R2 register waits for the fault to clear before sending the clear forward line signal. In the case of recognition of bb = 0 while in the seize acknowledge state prior to the answer signal, no immediate action is taken. However, the clear forward signal will be sent if bb = 1 is restored or the seize acknowledge guard timeout is reached. This value is expressed in milliseconds (ms). " DEFVAL { 250 } ::= { r2TimerVariantsEntry 2100 } -- Columnar:Fault On Seize Guard Timeout r2TimerVariantsFaultOnSeizeGuardTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..86400000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Fault On Seize Guard Timeout The maximum time an outgoing R2 register waits for the fault to clear before sending the clear forward line signal. In the case of recognition of bb = 0 while in the seize state, no immediate action is taken. However, when the seize acknowledgement signal is recognized after the seize ack timeout period has elapsed or the seize guard timeout, the clear forward signal will be sent. This value is expressed in milliseconds (ms). " DEFVAL { 250 } ::= { r2TimerVariantsEntry 2200 } -- Columnar:Decline Guard Timeout r2TimerVariantsDeclineGuardTimeout OBJECT-TYPE SYNTAX Integer32 ( 1000..2000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Decline Guard Timeout Maximum time the AB=10 release signal is applied before sending the AB=11 clearback signal. This parameter applies when the IncomingDeclineMethod parameter is set to 'ClearBack' while declining a call. This value is expressed in milliseconds (ms). " DEFVAL { 1500 } ::= { r2TimerVariantsEntry 2250 } -- Row command:Reset Specific r2TimerVariantsResetSpecific OBJECT-TYPE SYNTAX INTEGER { noOp(0), resetSpecific(10) } MAX-ACCESS read-write STATUS current DESCRIPTION " Reset Specific Resets specific settings of R2 Timers parameters with the default country settings. This command is used to retrieve the default country configuration set in the CountrySelection parameter. " DEFVAL { noOp } ::= { r2TimerVariantsEntry 2300 } -- Columnar:Override Default r2TimerVariantsOverrideDefault OBJECT-TYPE SYNTAX MxEnableState MAX-ACCESS read-write STATUS current DESCRIPTION " Override Default Overrides the default setting of R2 Timers for the CountrySelection and InterfaceName. * Disable: The interface uses the default country configuration. The configuration set in the current row has no effects on the default country configuration. Refer to the technical documentation to get the default country timers configuration. * Enable: The interface uses the specific country configuration as defined in the current row. To retrieve the default configuration associated with the current country, the parameter reset MUST be enabled. " DEFVAL { disable } ::= { r2TimerVariantsEntry 300 } -- Columnar:Seizure Ack Timeout r2TimerVariantsSeizureAckTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..10000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Seizure Ack Timeout Maximum time an outgoing R2 register waits for the seizure acknowledgement signal after sending a seizure signal. This value is expressed in milliseconds (ms). " DEFVAL { 2000 } ::= { r2TimerVariantsEntry 400 } -- Columnar:Fault Seizure Ack Timeout r2TimerVariantsFaultSeizureAckTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..100000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Fault Seizure Ack Timeout Maximum time an incoming R2 register waits for a seizure acknowledge failure condition to clear. This value is expressed in milliseconds (ms). " DEFVAL { 60000 } ::= { r2TimerVariantsEntry 500 } -- Columnar:Double Seizure Timeout r2TimerVariantsDoubleSeizureTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..1000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Double Seizure Timeout Minimum time an outgoing R2 register waits after a double seizure is recognized before releasing the connection. This value is expressed in milliseconds (ms). " DEFVAL { 100 } ::= { r2TimerVariantsEntry 600 } -- Columnar:Double Answer Timeout r2TimerVariantsDoubleAnswerTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..90000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Double Answer Timeout Maximum time an outgoing R2 register waits after receiving a clear-backward signal before releasing the connection. This value is expressed in milliseconds (ms). " DEFVAL { 1500 } ::= { r2TimerVariantsEntry 700 } -- Columnar:Answer Timeout r2TimerVariantsAnswerTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..8000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Answer Timeout Maximum time the answer signal AB=01 is applied before the clear backward signal AB=11 is sent. This parameter is generally used to reject collect calls (toll) and is only available if the CollectCallBlocked parameter is enabled. A value of 0 means that the signal is applied until the call is disconnected. However, if a special event (flash hook) is detected in the answered state then the clear backward signal AB=11 is immediately applied for a period corresponding to ReAnswerTimeout. This value is expressed in milliseconds (ms). " DEFVAL { 0 } ::= { r2TimerVariantsEntry 710 } -- Columnar:ReAnswer Timeout r2TimerVariantsReAnswerTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..8000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " ReAnswer Timeout Maximum time the clear backward signal AB=11 is applied before the answer signal AB=01 is reapplied again. This parameter is generally used to reject collect calls (toll) and is only available if the CollectCallBlocked parameter is enabled. The ReAnswerTimeout parameter is only applied if the AnswerTimeout or an event generating the clear backward signal is triggered. This value is expressed in milliseconds (ms). " DEFVAL { 1000 } ::= { r2TimerVariantsEntry 720 } -- Columnar:Release Guard Timeout r2TimerVariantsReleaseGuardTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..4000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Release Guard Timeout Maximum time an incoming R2 register waits after sending an idle line signal to prevent a new seizure of the line when a clear forward line signal is received. This value is expressed in milliseconds (ms). " DEFVAL { 100 } ::= { r2TimerVariantsEntry 800 } -- Columnar:Inter-call Guard Timeout r2TimerVariantsInterCallGuardTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..15000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Inter-call Guard Timeout Maximum time an outgoing R2 register waits after receiving an idle line signal before attempting a new seizure of the line. This value is expressed in milliseconds (ms). " DEFVAL { 100 } ::= { r2TimerVariantsEntry 820 } -- Columnar:No Digit Detected Timeout r2TimerVariantsNoDigitTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..120000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " No Digit Detected Timeout Maximum time an incoming R2 register waits before sending the congestion tone when no digits are received. This value is expressed in milliseconds (ms). " DEFVAL { 0 } ::= { r2TimerVariantsEntry 830 } -- Columnar:Congestion Tone Guard Timeout r2TimerVariantsCongestionToneGuardTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..200000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Congestion Tone Guard Timeout Maximum time an incoming R2 register waits after sending a congestion tone before sending a clear forward line signal and transits to the idle state. This value is expressed in milliseconds (ms). " DEFVAL { 1000 } ::= { r2TimerVariantsEntry 850 } -- Columnar:Unblocking Timeout r2TimerVariantsUnblockingTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..4000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Unblocking Timeout Maximum time a both-way trunk waits before assuming an idle state when a blocking condition is removed. This will prevent a too aggressive seizure of the trunk. This value is expressed in milliseconds (ms). " DEFVAL { 100 } ::= { r2TimerVariantsEntry 900 } -- End of table:R2 Signaling Timer Variants -- *************************************************************************** -- Table:R2 Digit Timer Variants -- *************************************************************************** r2DigitTimerVariantsTable OBJECT-TYPE SYNTAX SEQUENCE OF R2DigitTimerVariantsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " R2 Digit Timer Variants This table allows to override or retrieve the default country setting for R2 Digit Timers. " ::= { r2Group 400 } r2DigitTimerVariantsEntry OBJECT-TYPE SYNTAX R2DigitTimerVariantsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A row in table R2 Digit Timer Variants. " INDEX { r2DigitTimerVariantsInterfaceName } ::= { r2DigitTimerVariantsTable 1 } R2DigitTimerVariantsEntry ::= SEQUENCE { r2DigitTimerVariantsInterfaceName OCTET STRING, r2DigitTimerVariantsOverrideDefault MxEnableState, r2DigitTimerVariantsMfCongestionToneDuration Integer32, r2DigitTimerVariantsMfcPulseInterDigitTimeout Integer32, r2DigitTimerVariantsMfcPulseMinOnTimeout Integer32, r2DigitTimerVariantsMfcMaxSequenceTimeout Integer32, r2DigitTimerVariantsMfcMaxOnTimeout Integer32, r2DigitTimerVariantsMfcMaxOffTimeout Integer32, r2DigitTimerVariantsResetSpecific INTEGER } -- Index:Interface Name r2DigitTimerVariantsInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " Interface Name Identifies the interface. " ::= { r2DigitTimerVariantsEntry 100 } -- Columnar:Override Default r2DigitTimerVariantsOverrideDefault OBJECT-TYPE SYNTAX MxEnableState MAX-ACCESS read-write STATUS current DESCRIPTION " Override Default Overrides the default setting of R2 Digit timers for the CountrySelection and InterfaceName. * Disable: The interface uses the default country configuration. The configuration set in the current row has no effects on the default country configuration. Refer to the technical documentation to get the default country timers configuration. * Enable: The interface uses the specific country configuration as defined in the current row. To retrieve the default configuration associated with the current country, the parameter reset MUST be enabled. " DEFVAL { disable } ::= { r2DigitTimerVariantsEntry 300 } -- Columnar:MF Congestion Tone Duration r2DigitTimerVariantsMfCongestionToneDuration OBJECT-TYPE SYNTAX Integer32 ( 0..120000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " MF Congestion Tone Duration Allows the administrator to specifically configures the duration of the transmission of the congestion tone. The special value '0' sets the duration according to the R2DigitTimerVariants.MfcPulseMinOnTimeout parameter, which sets the minimum duration of all backward tones. This value is expressed in milliseconds (ms). " DEFVAL { 0 } ::= { r2DigitTimerVariantsEntry 350 } -- Columnar:MFC Pulse Inter Digit Timeout r2DigitTimerVariantsMfcPulseInterDigitTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..1000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " MFC Pulse Inter Digit Timeout The minimum delay between the end of transmission of the last signal of the compelled cycle and the start of the next one. This value is expressed in milliseconds (ms). " DEFVAL { 100 } ::= { r2DigitTimerVariantsEntry 400 } -- Columnar:MFC Minimum Pulse OnTimeout r2DigitTimerVariantsMfcPulseMinOnTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..1000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " MFC Minimum Pulse OnTimeout The minimum time a backward tone can be on from the backward perspective. This value is expressed in milliseconds (ms). " DEFVAL { 150 } ::= { r2DigitTimerVariantsEntry 500 } -- Columnar:MFC Maximum Sequence Timeout r2DigitTimerVariantsMfcMaxSequenceTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..70000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " MFC Maximum Sequence Timeout The maximum time for a complete compelled signaling cycle from the forward perspective. This value is expressed in milliseconds (ms). " DEFVAL { 10000 } ::= { r2DigitTimerVariantsEntry 600 } -- Columnar:MFC Maximum On Timeout r2DigitTimerVariantsMfcMaxOnTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..35000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " MFC Maximum On Timeout The maximum time a forward tone can be on from the forward perspective. This value is expressed in milliseconds (ms). " DEFVAL { 5000 } ::= { r2DigitTimerVariantsEntry 700 } -- Columnar:MFC Maximum Off Timeout r2DigitTimerVariantsMfcMaxOffTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..35000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " MFC Maximum Off Timeout The maximum time a forward tone can be off from the forward perspective. This value is expressed in milliseconds (ms). " DEFVAL { 5000 } ::= { r2DigitTimerVariantsEntry 800 } -- Row command:Reset Specific r2DigitTimerVariantsResetSpecific OBJECT-TYPE SYNTAX INTEGER { noOp(0), resetSpecific(10) } MAX-ACCESS read-write STATUS current DESCRIPTION " Reset Specific Resets specific settings of R2 Digit Timers parameters with the default country settings. This command is used to retrieve the default country configuration set in the CountrySelection parameter. " DEFVAL { noOp } ::= { r2DigitTimerVariantsEntry 900 } -- End of table:R2 Digit Timer Variants -- *************************************************************************** -- Table:R2 Link Timer Variants -- *************************************************************************** r2LinkTimerVariantsTable OBJECT-TYPE SYNTAX SEQUENCE OF R2LinkTimerVariantsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " R2 Link Timer Variants This table allows to override or retrieve the default country setting for R2 Link Timers. " ::= { r2Group 500 } r2LinkTimerVariantsEntry OBJECT-TYPE SYNTAX R2LinkTimerVariantsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A row in table R2 Link Timer Variants. " INDEX { r2LinkTimerVariantsInterfaceName } ::= { r2LinkTimerVariantsTable 1 } R2LinkTimerVariantsEntry ::= SEQUENCE { r2LinkTimerVariantsInterfaceName OCTET STRING, r2LinkTimerVariantsOverrideDefault MxEnableState, r2LinkTimerVariantsLinkActivationTimeout Integer32, r2LinkTimerVariantsLinkActivationRetryTimeout Integer32, r2LinkTimerVariantsResetSpecific INTEGER } -- Index:Interface Name r2LinkTimerVariantsInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " Interface Name Identifies the interface. " ::= { r2LinkTimerVariantsEntry 100 } -- Columnar:Override Default r2LinkTimerVariantsOverrideDefault OBJECT-TYPE SYNTAX MxEnableState MAX-ACCESS read-write STATUS current DESCRIPTION " Override Default Overrides the default setting of R2 Link timers for the CountrySelection and InterfaceName. * Disable: The interface uses the default country configuration. The configuration set in the current row has no effects on the default country configuration. Refer to the technical documentation to get the default country timers configuration. * Enable: The interface uses the specific country configuration as defined in the current row. To retrieve the default configuration associated with the current country, the parameter reset MUST be enabled. " DEFVAL { disable } ::= { r2LinkTimerVariantsEntry 300 } -- Columnar:Link Activation Timeout r2LinkTimerVariantsLinkActivationTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..10000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Link Activation Timeout The maximum time the unit waits for an activation indication coming from the physical link. The activation indication is used to indicate that the physical layer connection has been activated. This value is expressed in milliseconds (ms). " DEFVAL { 1000 } ::= { r2LinkTimerVariantsEntry 400 } -- Columnar:Link Activation Retry Timeout r2LinkTimerVariantsLinkActivationRetryTimeout OBJECT-TYPE SYNTAX Integer32 ( 0..10000 ) MAX-ACCESS read-write STATUS current DESCRIPTION " Link Activation Retry Timeout The maximum time the unit waits before attempting to reestablish the physical link. The attempt is made when the physical layer connection has been deactivated. This value is expressed in milliseconds (ms). " DEFVAL { 3000 } ::= { r2LinkTimerVariantsEntry 500 } -- Row command:Reset Specific r2LinkTimerVariantsResetSpecific OBJECT-TYPE SYNTAX INTEGER { noOp(0), resetSpecific(10) } MAX-ACCESS read-write STATUS current DESCRIPTION " Reset Specific Resets specific settings of R2 Link Timers parameters with the default country settings. This command is used to retrieve the default country configuration set in the CountrySelection parameter. " DEFVAL { noOp } ::= { r2LinkTimerVariantsEntry 600 } -- End of table:R2 Link Timer Variants -- *************************************************************************** -- Table:R2 Signaling Tone Variants -- *************************************************************************** r2ToneVariantsTable OBJECT-TYPE SYNTAX SEQUENCE OF R2ToneVariantsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " R2 Signaling Tone Variants This table allows to override or retrieve the default country setting for R2 Tone variants in forward and backward group. " ::= { r2Group 600 } r2ToneVariantsEntry OBJECT-TYPE SYNTAX R2ToneVariantsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A row in table R2 Signaling Tone Variants. " INDEX { r2ToneVariantsInterfaceName } ::= { r2ToneVariantsTable 1 } R2ToneVariantsEntry ::= SEQUENCE { r2ToneVariantsInterfaceName OCTET STRING, r2ToneVariantsOverrideDefault MxEnableState, r2ToneVariantsFwdGroup1EndOfDnis INTEGER, r2ToneVariantsFwdGroup1EndOfAni INTEGER, r2ToneVariantsFwdGroup1RestrictedAni INTEGER, r2ToneVariantsBwdGroupASendNextDnisDigit INTEGER, r2ToneVariantsBwdGroupASendPreviousDnisDigit INTEGER, r2ToneVariantsBwdGroupASwitchToGroupII INTEGER, r2ToneVariantsBwdGroupANetworkCongestion INTEGER, r2ToneVariantsBwdGroupASendCallingPartyCategory INTEGER, r2ToneVariantsBwdGroupAImmediateAccept INTEGER, r2ToneVariantsBwdGroupASendDnisDigitNMinus2 INTEGER, r2ToneVariantsBwdGroupASendDnisDigitNMinus3 INTEGER, r2ToneVariantsBwdGroupARepeatAllDnis INTEGER, r2ToneVariantsBwdGroupASendNextAniDigit INTEGER, r2ToneVariantsBwdGroupASendCallingPartyCategorySwitchGroupC INTEGER, r2ToneVariantsBwdGroupBSendSit INTEGER, r2ToneVariantsBwdGroupBUserBusy INTEGER, r2ToneVariantsBwdGroupBNetworkCongestion INTEGER, r2ToneVariantsBwdGroupBUnassignedNumber INTEGER, r2ToneVariantsBwdGroupBLineFreeCharge INTEGER, r2ToneVariantsBwdGroupBSupplementaryLineFreeCharge INTEGER, r2ToneVariantsBwdGroupBLineFreeNoCharge INTEGER, r2ToneVariantsBwdGroupBLineOutOfOrder INTEGER, r2ToneVariantsBwdGroupBChangedNumber INTEGER, r2ToneVariantsBwdGroupCSendNextAniDigit INTEGER, r2ToneVariantsBwdGroupCRepeatAllDnisSwitchGroupA INTEGER, r2ToneVariantsBwdGroupCSendNextDnisDigitSwitchGroupA INTEGER, r2ToneVariantsBwdGroupCNetworkCongestion INTEGER, r2ToneVariantsBwdGroupCSendPreviousDnisDigitSwitchGroupA INTEGER, r2ToneVariantsBwdGroupCSwitchGroupII INTEGER, r2ToneVariantsResetSpecific INTEGER } -- Index:Interface Name r2ToneVariantsInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " Interface Name Identifies the interface. " ::= { r2ToneVariantsEntry 100 } -- Columnar:Backward Group A SendCallingPartyCategory Tone r2ToneVariantsBwdGroupASendCallingPartyCategory OBJECT-TYPE SYNTAX INTEGER { none(100) , a1(200) , a2(300) , a3(400) , a4(500) , a5(600) , a6(700) , a7(800) , a8(900) , a9(1000) , a10(1100) , a11(1200) , a12(1300) , a13(1400) , a14(1500) , a15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group A SendCallingPartyCategory Tone Specifies the backward Group A tone sent when the backward group requests the calling party category. * None: No tone used. * A1..A15: Group A backward signal MF Tones " DEFVAL { a15 } ::= { r2ToneVariantsEntry 1000 } -- Columnar:Backward Group A ImmediateAccept Tone r2ToneVariantsBwdGroupAImmediateAccept OBJECT-TYPE SYNTAX INTEGER { none(100) , a1(200) , a2(300) , a3(400) , a4(500) , a5(600) , a6(700) , a7(800) , a8(900) , a9(1000) , a10(1100) , a11(1200) , a12(1300) , a13(1400) , a14(1500) , a15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group A ImmediateAccept Tone Specifies the backward Group A tone sent when the backward group accepts the call immediatly. * None: No tone used. * A1..A15: Group A backward signal MF Tones " DEFVAL { a15 } ::= { r2ToneVariantsEntry 1100 } -- Columnar:Backward Group A BwdGroupASendDnisDigitNMinus2 Tone r2ToneVariantsBwdGroupASendDnisDigitNMinus2 OBJECT-TYPE SYNTAX INTEGER { none(100) , a1(200) , a2(300) , a3(400) , a4(500) , a5(600) , a6(700) , a7(800) , a8(900) , a9(1000) , a10(1100) , a11(1200) , a12(1300) , a13(1400) , a14(1500) , a15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group A BwdGroupASendDnisDigitNMinus2 Tone Specifies the backward Group A tone used to request the previous - 1 DNIS digit. * None: No tone used. * A1..A15: Group A backward signal MF Tones " DEFVAL { a15 } ::= { r2ToneVariantsEntry 1200 } -- Columnar:Backward Group A BwdGroupASendDnisDigitNMinus3 Tone r2ToneVariantsBwdGroupASendDnisDigitNMinus3 OBJECT-TYPE SYNTAX INTEGER { none(100) , a1(200) , a2(300) , a3(400) , a4(500) , a5(600) , a6(700) , a7(800) , a8(900) , a9(1000) , a10(1100) , a11(1200) , a12(1300) , a13(1400) , a14(1500) , a15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group A BwdGroupASendDnisDigitNMinus3 Tone Specifies the backward Group A tone used to request the previous - 2 DNIS digit. * None: No tone used. * A1..A15: Group A backward signal MF Tones " DEFVAL { a15 } ::= { r2ToneVariantsEntry 1300 } -- Columnar:Backward Group A BwdGroupARepeatAllDnis Tone r2ToneVariantsBwdGroupARepeatAllDnis OBJECT-TYPE SYNTAX INTEGER { none(100) , a1(200) , a2(300) , a3(400) , a4(500) , a5(600) , a6(700) , a7(800) , a8(900) , a9(1000) , a10(1100) , a11(1200) , a12(1300) , a13(1400) , a14(1500) , a15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group A BwdGroupARepeatAllDnis Tone Specifies the backward Group A tone used to request all DNIS digits. * None: No tone used. * A1..A15: Group A backward signal MF Tones " DEFVAL { a15 } ::= { r2ToneVariantsEntry 1400 } -- Columnar:Backward Group A BwdGroupASendNextAniDigit Tone r2ToneVariantsBwdGroupASendNextAniDigit OBJECT-TYPE SYNTAX INTEGER { none(100) , a1(200) , a2(300) , a3(400) , a4(500) , a5(600) , a6(700) , a7(800) , a8(900) , a9(1000) , a10(1100) , a11(1200) , a12(1300) , a13(1400) , a14(1500) , a15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group A BwdGroupASendNextAniDigit Tone Specifies the backward Group A tone used to request the next ANI digit. * None: No tone used. * A1..A15: Group A backward signal MF Tones " DEFVAL { a15 } ::= { r2ToneVariantsEntry 1500 } -- Columnar:Backward Group A BwdGroupASendCallingPartyCategorySwitchGroupC -- Tone r2ToneVariantsBwdGroupASendCallingPartyCategorySwitchGroupC OBJECT-TYPE SYNTAX INTEGER { none(100) , a1(200) , a2(300) , a3(400) , a4(500) , a5(600) , a6(700) , a7(800) , a8(900) , a9(1000) , a10(1100) , a11(1200) , a12(1300) , a13(1400) , a14(1500) , a15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group A BwdGroupASendCallingPartyCategorySwitchGroupC Tone Specifies the backward Group A tone used to request the calling party category and then switch to Group C signals. * None: No tone used. * A1..A15: Group A backward signal MF Tones " DEFVAL { a15 } ::= { r2ToneVariantsEntry 1550 } -- Columnar:Backward Group B BwdGroupBSendSpecialToneInformation Tone r2ToneVariantsBwdGroupBSendSit OBJECT-TYPE SYNTAX INTEGER { none(100) , b1(200) , b2(300) , b3(400) , b4(500) , b5(600) , b6(700) , b7(800) , b8(900) , b9(1000) , b10(1100) , b11(1200) , b12(1300) , b13(1400) , b14(1500) , b15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group B BwdGroupBSendSpecialToneInformation Tone Specifies the backward Group B tone used to send a special information tone. * None: No tone used. * B1..B15: Group B backward signal MF Tones " DEFVAL { b15 } ::= { r2ToneVariantsEntry 1600 } -- Columnar:Backward Group B BwdGroupBUserBusy Tone r2ToneVariantsBwdGroupBUserBusy OBJECT-TYPE SYNTAX INTEGER { none(100) , b1(200) , b2(300) , b3(400) , b4(500) , b5(600) , b6(700) , b7(800) , b8(900) , b9(1000) , b10(1100) , b11(1200) , b12(1300) , b13(1400) , b14(1500) , b15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group B BwdGroupBUserBusy Tone Specifies the backward Group B tone used to signal a user busy. * None: No tone used. * B1..B15: Group B backward signal MF Tones " DEFVAL { b15 } ::= { r2ToneVariantsEntry 1700 } -- Columnar:Backward Group B BwdGroupBNetworkCongestion Tone r2ToneVariantsBwdGroupBNetworkCongestion OBJECT-TYPE SYNTAX INTEGER { none(100) , b1(200) , b2(300) , b3(400) , b4(500) , b5(600) , b6(700) , b7(800) , b8(900) , b9(1000) , b10(1100) , b11(1200) , b12(1300) , b13(1400) , b14(1500) , b15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group B BwdGroupBNetworkCongestion Tone Specifies the backward Group B tone used to signal a network congestion. * None: No tone used. * B1..B15: Group B backward signal MF Tones " DEFVAL { b15 } ::= { r2ToneVariantsEntry 1800 } -- Columnar:Backward Group B BwdGroupBUnassignedNumber Tone r2ToneVariantsBwdGroupBUnassignedNumber OBJECT-TYPE SYNTAX INTEGER { none(100) , b1(200) , b2(300) , b3(400) , b4(500) , b5(600) , b6(700) , b7(800) , b8(900) , b9(1000) , b10(1100) , b11(1200) , b12(1300) , b13(1400) , b14(1500) , b15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group B BwdGroupBUnassignedNumber Tone Specifies the backward Group B tone used to signal an unassigned number. * None: No tone used. * B1..B15: Group B backward signal MF Tones " DEFVAL { b15 } ::= { r2ToneVariantsEntry 1900 } -- Columnar:Backward Group B BwdGroupBLineFreeCharge Tone r2ToneVariantsBwdGroupBLineFreeCharge OBJECT-TYPE SYNTAX INTEGER { none(100) , b1(200) , b2(300) , b3(400) , b4(500) , b5(600) , b6(700) , b7(800) , b8(900) , b9(1000) , b10(1100) , b11(1200) , b12(1300) , b13(1400) , b14(1500) , b15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group B BwdGroupBLineFreeCharge Tone Specifies the backward Group B tone used to signal that the line is free and charge must be applied. * None: No tone used. * B1..B15: Group B backward signal MF Tones " DEFVAL { b15 } ::= { r2ToneVariantsEntry 2000 } -- Columnar:Backward Group B BwdGroupBSupplementaryLineFreeCharge Tone r2ToneVariantsBwdGroupBSupplementaryLineFreeCharge OBJECT-TYPE SYNTAX INTEGER { none(100) , b1(200) , b2(300) , b3(400) , b4(500) , b5(600) , b6(700) , b7(800) , b8(900) , b9(1000) , b10(1100) , b11(1200) , b12(1300) , b13(1400) , b14(1500) , b15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group B BwdGroupBSupplementaryLineFreeCharge Tone Specifies a supplementary backward Group B tone used to detect that the line is free and charge must be applied. This is a supplementary (optionnal) tone used on the reception only. * None: No tone used. * B1..B15: Group B backward signal MF Tones " DEFVAL { b15 } ::= { r2ToneVariantsEntry 2100 } -- Columnar:Backward Group B BwdGroupBLineFreeNoCharge Tone r2ToneVariantsBwdGroupBLineFreeNoCharge OBJECT-TYPE SYNTAX INTEGER { none(100) , b1(200) , b2(300) , b3(400) , b4(500) , b5(600) , b6(700) , b7(800) , b8(900) , b9(1000) , b10(1100) , b11(1200) , b12(1300) , b13(1400) , b14(1500) , b15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group B BwdGroupBLineFreeNoCharge Tone Specifies the backward Group B tone used to signal that the line is free and no charges must be applied. * None: No tone used. * B1..B15: Group B backward signal MF Tones " DEFVAL { b15 } ::= { r2ToneVariantsEntry 2200 } -- Columnar:Backward Group B BwdGroupBLineOutOfOrder Tone r2ToneVariantsBwdGroupBLineOutOfOrder OBJECT-TYPE SYNTAX INTEGER { none(100) , b1(200) , b2(300) , b3(400) , b4(500) , b5(600) , b6(700) , b7(800) , b8(900) , b9(1000) , b10(1100) , b11(1200) , b12(1300) , b13(1400) , b14(1500) , b15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group B BwdGroupBLineOutOfOrder Tone Specifies the backward Group B tone used to signal that the line is out of order. * None: No tone used. * B1..B15: Group B backward signal MF Tones " DEFVAL { b15 } ::= { r2ToneVariantsEntry 2300 } -- Columnar:Backward Group B BwdGroupBChangedNumber Tone r2ToneVariantsBwdGroupBChangedNumber OBJECT-TYPE SYNTAX INTEGER { none(100) , b1(200) , b2(300) , b3(400) , b4(500) , b5(600) , b6(700) , b7(800) , b8(900) , b9(1000) , b10(1100) , b11(1200) , b12(1300) , b13(1400) , b14(1500) , b15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group B BwdGroupBChangedNumber Tone Specifies the backward Group B tone used to signal that the subscriber has changed number. * None: No tone used. * B1..B15: Group B backward signal MF Tones " DEFVAL { b15 } ::= { r2ToneVariantsEntry 2350 } -- Columnar:Backward Group C BwdGroupCSendNextAniDigit Tone r2ToneVariantsBwdGroupCSendNextAniDigit OBJECT-TYPE SYNTAX INTEGER { none(100) , c1(200) , c2(300) , c3(400) , c4(500) , c5(600) , c6(700) , c7(800) , c8(900) , c9(1000) , c10(1100) , c11(1200) , c12(1300) , c13(1400) , c14(1500) , c15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group C BwdGroupCSendNextAniDigit Tone Specifies the backward Group C tone used to request the next ANI digit. * None: No tone used. * C1..C15: Group C backward signal MF Tones " DEFVAL { c15 } ::= { r2ToneVariantsEntry 2355 } -- Columnar:Backward Group C BwdCRepeatAllDnisSwitchGroupA Tone r2ToneVariantsBwdGroupCRepeatAllDnisSwitchGroupA OBJECT-TYPE SYNTAX INTEGER { none(100) , c1(200) , c2(300) , c3(400) , c4(500) , c5(600) , c6(700) , c7(800) , c8(900) , c9(1000) , c10(1100) , c11(1200) , c12(1300) , c13(1400) , c14(1500) , c15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group C BwdCRepeatAllDnisSwitchGroupA Tone Specifies the backward Group C tone used to request all DNIS digits and then switch to Group A signals. * None: No tone used. * C1..C15: Group C backward signal MF Tones " DEFVAL { c15 } ::= { r2ToneVariantsEntry 2360 } -- Columnar:Backward Group C BwdCSendNextDnisDigitSwitchGroupA Tone r2ToneVariantsBwdGroupCSendNextDnisDigitSwitchGroupA OBJECT-TYPE SYNTAX INTEGER { none(100) , c1(200) , c2(300) , c3(400) , c4(500) , c5(600) , c6(700) , c7(800) , c8(900) , c9(1000) , c10(1100) , c11(1200) , c12(1300) , c13(1400) , c14(1500) , c15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group C BwdCSendNextDnisDigitSwitchGroupA Tone Specifies the backward Group C tone used to request the next DNIS digit and then switch to Group A signals. * None: No tone used. * C1..C15: Group C backward signal MF Tones " DEFVAL { c15 } ::= { r2ToneVariantsEntry 2365 } -- Columnar:Backward Group C BwdGroupCNetworkCongestion Tone r2ToneVariantsBwdGroupCNetworkCongestion OBJECT-TYPE SYNTAX INTEGER { none(100) , c1(200) , c2(300) , c3(400) , c4(500) , c5(600) , c6(700) , c7(800) , c8(900) , c9(1000) , c10(1100) , c11(1200) , c12(1300) , c13(1400) , c14(1500) , c15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group C BwdGroupCNetworkCongestion Tone Specifies the backward Group C tone used to signal a network congestion. * None: No tone used. * C1..C15: Group C backward signal MF Tones " DEFVAL { c15 } ::= { r2ToneVariantsEntry 2370 } -- Columnar:Backward Group C BwdCSendPreviousDnisDigitSwitchGroupA Tone r2ToneVariantsBwdGroupCSendPreviousDnisDigitSwitchGroupA OBJECT-TYPE SYNTAX INTEGER { none(100) , c1(200) , c2(300) , c3(400) , c4(500) , c5(600) , c6(700) , c7(800) , c8(900) , c9(1000) , c10(1100) , c11(1200) , c12(1300) , c13(1400) , c14(1500) , c15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group C BwdCSendPreviousDnisDigitSwitchGroupA Tone Specifies the backward Group C tone used to request the previous DNIS digit and then switch to Group A signals. * None: No tone used. * C1..C15: Group C backward signal MF Tones " DEFVAL { c15 } ::= { r2ToneVariantsEntry 2375 } -- Columnar:Backward Group C BwdCSwitchGroupII Tone r2ToneVariantsBwdGroupCSwitchGroupII OBJECT-TYPE SYNTAX INTEGER { none(100) , c1(200) , c2(300) , c3(400) , c4(500) , c5(600) , c6(700) , c7(800) , c8(900) , c9(1000) , c10(1100) , c11(1200) , c12(1300) , c13(1400) , c14(1500) , c15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group C BwdCSwitchGroupII Tone Specifies the backward Group C tone used to request to the caller a switch of Group II signals. * None: No tone used. * C1..C15: Group C backward signal MF Tones " DEFVAL { c15 } ::= { r2ToneVariantsEntry 2380 } -- Row command:Reset Specific r2ToneVariantsResetSpecific OBJECT-TYPE SYNTAX INTEGER { noOp(0), resetSpecific(10) } MAX-ACCESS read-write STATUS current DESCRIPTION " Reset Specific Resets specific settings of R2 Tones parameters with the default country settings. This command is used to retrieve the default country configuration set in the CountrySelection parameter. " DEFVAL { noOp } ::= { r2ToneVariantsEntry 2400 } -- Columnar:Override Default r2ToneVariantsOverrideDefault OBJECT-TYPE SYNTAX MxEnableState MAX-ACCESS read-write STATUS current DESCRIPTION " Override Default Overrides the default setting of R2 tone variants for the CountrySelection and InterfaceName. * Disable: The interface uses the default country configuration. The configuration set in the current row has no effects on the default country configuration. Refer to the technical documentation to get the default country tones configuration. * Enable: The interface uses the specific country configuration as defined in the current row. To retrieve the default configuration associated with the current country, the parameter reset MUST be enabled. " DEFVAL { disable } ::= { r2ToneVariantsEntry 300 } -- Columnar:Forward Group 1 EndOfDnis Tone r2ToneVariantsFwdGroup1EndOfDnis OBJECT-TYPE SYNTAX INTEGER { none(100) , i1(200) , i2(300) , i3(400) , i4(500) , i5(600) , i6(700) , i7(800) , i8(900) , i9(1000) , i10(1100) , i11(1200) , i12(1300) , i13(1400) , i14(1500) , i15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Forward Group 1 EndOfDnis Tone Specifies the forward Group 1 tone used to send after the DNIS digits. * None: No tone used. * I1..I15: Group 1 forward signal MF Tones " DEFVAL { i15 } ::= { r2ToneVariantsEntry 400 } -- Columnar:Forward Group 1 EndOfAni Tone r2ToneVariantsFwdGroup1EndOfAni OBJECT-TYPE SYNTAX INTEGER { none(100) , i1(200) , i2(300) , i3(400) , i4(500) , i5(600) , i6(700) , i7(800) , i8(900) , i9(1000) , i10(1100) , i11(1200) , i12(1300) , i13(1400) , i14(1500) , i15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Forward Group 1 EndOfAni Tone Specifies the forward Group 1 tone used to send after the ANI digits. * None: No tone used. * I1..I15: Group 1 forward signal MF Tones " DEFVAL { i15 } ::= { r2ToneVariantsEntry 500 } -- Columnar:Forward Group 1 Restricted ANI Tone r2ToneVariantsFwdGroup1RestrictedAni OBJECT-TYPE SYNTAX INTEGER { none(100) , i1(200) , i2(300) , i3(400) , i4(500) , i5(600) , i6(700) , i7(800) , i8(900) , i9(1000) , i10(1100) , i11(1200) , i12(1300) , i13(1400) , i14(1500) , i15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Forward Group 1 Restricted ANI Tone Specifies the forward Group 1 tone used to reject a send next digit (ANI). This tone is generally used in response to the identification request when the caller party is unable to send his identification to the called party. If no tone is defined, the FwdGroup1EndOfAni tone is sent to the caller. * None: No tone used. * I1..I15: Group 1 forward signal MF Tones " DEFVAL { i12 } ::= { r2ToneVariantsEntry 520 } -- Columnar:Backward Group A SendNextDnisDigit Tone r2ToneVariantsBwdGroupASendNextDnisDigit OBJECT-TYPE SYNTAX INTEGER { none(100) , a1(200) , a2(300) , a3(400) , a4(500) , a5(600) , a6(700) , a7(800) , a8(900) , a9(1000) , a10(1100) , a11(1200) , a12(1300) , a13(1400) , a14(1500) , a15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group A SendNextDnisDigit Tone Specifies the backward Group A tone used to request the next DNIS digit. * None: No tone used. * A1..A15: Group A backward signal MF Tones " DEFVAL { a15 } ::= { r2ToneVariantsEntry 600 } -- Columnar:Backward Group A SendPreviousDnisDigit Tone r2ToneVariantsBwdGroupASendPreviousDnisDigit OBJECT-TYPE SYNTAX INTEGER { none(100) , a1(200) , a2(300) , a3(400) , a4(500) , a5(600) , a6(700) , a7(800) , a8(900) , a9(1000) , a10(1100) , a11(1200) , a12(1300) , a13(1400) , a14(1500) , a15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group A SendPreviousDnisDigit Tone Specifies the backward Group A tone used to request the previous DNIS digit. * None: No tone used. * A1..A15: Group A backward signal MF Tones " DEFVAL { a15 } ::= { r2ToneVariantsEntry 700 } -- Columnar:Backward Group A BwdGroupASwitchToGroupII Tone r2ToneVariantsBwdGroupASwitchToGroupII OBJECT-TYPE SYNTAX INTEGER { none(100) , a1(200) , a2(300) , a3(400) , a4(500) , a5(600) , a6(700) , a7(800) , a8(900) , a9(1000) , a10(1100) , a11(1200) , a12(1300) , a13(1400) , a14(1500) , a15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group A BwdGroupASwitchToGroupII Tone Specifies the backward Group A tone used to request to the caller a switch of Group II signals. * None: No tone used. * A1..A15: Group A backward signal MF Tones " DEFVAL { a15 } ::= { r2ToneVariantsEntry 800 } -- Columnar:Backward Group A NetworkCongestion Tone r2ToneVariantsBwdGroupANetworkCongestion OBJECT-TYPE SYNTAX INTEGER { none(100) , a1(200) , a2(300) , a3(400) , a4(500) , a5(600) , a6(700) , a7(800) , a8(900) , a9(1000) , a10(1100) , a11(1200) , a12(1300) , a13(1400) , a14(1500) , a15(1600) } MAX-ACCESS read-write STATUS current DESCRIPTION " Backward Group A NetworkCongestion Tone Specifies the backward Group A tone to be sent when a congestion network is detected. * None: No tone used. * A1..A15: Group A backward signal MF Tones " DEFVAL { a15 } ::= { r2ToneVariantsEntry 900 } -- End of table:R2 Signaling Tone Variants -- End of group:R2 Configuration -- **************************************************************************** -- Group:Bearer Channel Configuration -- **************************************************************************** bearerChannelGroup OBJECT IDENTIFIER ::= { r2MIBObjects 200 } -- *************************************************************************** -- Table:Bearer Channel Info -- *************************************************************************** bearerChannelInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF BearerChannelInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Bearer Channel Info Port-specific operational, statistics, and active call data for B channels. " ::= { bearerChannelGroup 100 } bearerChannelInfoEntry OBJECT-TYPE SYNTAX BearerChannelInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A row in table Bearer Channel Info. " INDEX { bearerChannelInfoIndex } ::= { bearerChannelInfoTable 1 } BearerChannelInfoEntry ::= SEQUENCE { bearerChannelInfoIndex OCTET STRING, bearerChannelInfoState INTEGER } -- Index:Index bearerChannelInfoIndex OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " Index Identifies the Bearer Channel.. " ::= { bearerChannelInfoEntry 100 } -- Columnar:State bearerChannelInfoState OBJECT-TYPE SYNTAX INTEGER { idle(100) , inUse(200) , maintenance(300) , error (400) , disabled(500) } MAX-ACCESS read-only STATUS current DESCRIPTION " State The current call control state for this channel: * Idle: The channel is available * InUse: The channel is currently used * Maintenance: Maintenance state, temporarily unavailable * Error: Error on this channel * Disabled: The channel is disabled " ::= { bearerChannelInfoEntry 200 } -- End of table:Bearer Channel Info -- End of group:Bearer Channel Configuration -- **************************************************************************** -- Group:Signaling Channel Configuration -- **************************************************************************** physicalGroup OBJECT IDENTIFIER ::= { r2MIBObjects 300 } -- *************************************************************************** -- Table:Physical Link Information -- *************************************************************************** physicalLinkInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF PhysicalLinkInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Physical Link Information The physical link information table contains status information for all interfaces on this managed device. " ::= { physicalGroup 100 } physicalLinkInfoEntry OBJECT-TYPE SYNTAX PhysicalLinkInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A row in table Physical Link Information. " INDEX { physicalLinkInfoInterfaceName } ::= { physicalLinkInfoTable 1 } PhysicalLinkInfoEntry ::= SEQUENCE { physicalLinkInfoInterfaceName OCTET STRING, physicalLinkInfoState INTEGER } -- Index:Interface Name physicalLinkInfoInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " Interface Name Identifies the interface. " ::= { physicalLinkInfoEntry 100 } -- Columnar:State physicalLinkInfoState OBJECT-TYPE SYNTAX INTEGER { up(100) , down(200) } MAX-ACCESS read-only STATUS current DESCRIPTION " State The layer 1 state for this interface: * Up: Layer 1 connectivity. * Down: No layer 1 connectivity. The interface might be in this state because no cable is plugged in or a pinout problem is detected. " ::= { physicalLinkInfoEntry 200 } -- End of table:Physical Link Information -- *************************************************************************** -- Table:Physical Link -- *************************************************************************** physicalLinkTable OBJECT-TYPE SYNTAX SEQUENCE OF PhysicalLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Physical Link The physical link table containing configuration and operational parameters for all interfaces on this managed device. " ::= { physicalGroup 200 } physicalLinkEntry OBJECT-TYPE SYNTAX PhysicalLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A row in table Physical Link. " INDEX { physicalLinkInterfaceName } ::= { physicalLinkTable 1 } PhysicalLinkEntry ::= SEQUENCE { physicalLinkInterfaceName OCTET STRING, physicalLinkLineCoding INTEGER, physicalLinkLineFraming INTEGER, physicalLinkClockMode INTEGER, physicalLinkMonitorLinkStateEnable MxEnableState, physicalLinkPortPinout INTEGER } -- Index:Interface Name physicalLinkInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " Interface Name Identifies the interface. " ::= { physicalLinkEntry 100 } -- Columnar:Line Coding physicalLinkLineCoding OBJECT-TYPE SYNTAX INTEGER { b8zs(100) , hdb3(200) , ami(300) } MAX-ACCESS read-write STATUS current DESCRIPTION " Line Coding Defines the transmission encoding of bits: * B8ZS: Bipolar with 8-Zeros Substitution (T1 lines) * HDB3: High-Density Bipolar Order 3 (E1 lines) * AMI: Alternate Mark Inversion (E1 and T1 lines) For further information, see ITU-T G.703 Recommendation. " DEFVAL { hdb3 } ::= { physicalLinkEntry 200 } -- Columnar:Line Framing physicalLinkLineFraming OBJECT-TYPE SYNTAX INTEGER { sf(100) , esf(200) , crc4(300) , noCrc4(400) } MAX-ACCESS read-write STATUS current DESCRIPTION " Line Framing Defines the frame format: * SF: Super frame. Sometimes known as D4 (T1 lines) * ESF: Extended super frame (T1 lines) * CRC4: Cyclic redundancy check 4 (E1 lines) * NO-CRC4: No Cyclic redundancy check 4 (E1 lines) For further information, see ITU-T G.704 Recommendation. " DEFVAL { crc4 } ::= { physicalLinkEntry 300 } -- Columnar:Clock Mode physicalLinkClockMode OBJECT-TYPE SYNTAX INTEGER { master(100) , slave(200) } MAX-ACCESS read-write STATUS current DESCRIPTION " Clock Mode A port can either generate the clocking for the line or accept the clock from the line. The options master or slave determine the clocking method: * Master: Generates clock * Slave: Accepts clock " DEFVAL { slave } ::= { physicalLinkEntry 400 } -- Columnar:Monitor Link State Enable physicalLinkMonitorLinkStateEnable OBJECT-TYPE SYNTAX MxEnableState MAX-ACCESS read-write STATUS current DESCRIPTION " Monitor Link State Enable Monitors the physical link state of an R2 interface. Enable: An R2 endpoint's operational state is affected by its interface physical link state. When the link state of an R2 interface is down, the operational state of its matching endpoint becomes 'disable'. Disable: An R2 endpoint's operational state is not affected by its interface physical link state. " DEFVAL { enable } ::= { physicalLinkEntry 500 } -- Columnar:Port Pinout physicalLinkPortPinout OBJECT-TYPE SYNTAX INTEGER { auto(100) , master(200) , slave(300) } MAX-ACCESS read-write STATUS current DESCRIPTION " Port Pinout Defines the port pinout: * Auto: The pinout is set according to the clock mode. * Master: Force the pinout to Master regardless of the clock mode. * Slave: Force the pinout to Slave regardless of the clock mode. See the PhysicalLink.ClockMode parameter for a description of the clock mode. " DEFVAL { auto } ::= { physicalLinkEntry 600 } -- End of table:Physical Link -- End of group:Signaling Channel Configuration -- **************************************************************************** -- Group:Automatic Configuration -- **************************************************************************** autoConfigure OBJECT IDENTIFIER ::= { r2MIBObjects 400 } -- Scalar:Auto Configure Status autoConfigureStatus OBJECT-TYPE SYNTAX INTEGER { idle(100) , sensing(200) } MAX-ACCESS read-only STATUS current DESCRIPTION " Auto Configure Status Indicates the current status of the R2 automatic configuration mechanism. * Idle: The automatic configuration mechanism is ready to be started. * Sensing: The automatic configuration mechanism is currently started and is testing different R2 configurations to obtain a link up. " ::= { autoConfigure 100 } -- Scalar:Last Auto Configure Result lastAutoConfigureResult OBJECT-TYPE SYNTAX INTEGER { none(100) , success(200) , fail(300) , aborted(400) } MAX-ACCESS read-only STATUS current DESCRIPTION " Last Auto Configure Result Result of the last R2 automatic configuration. * None: No result is available. * Success: The last automatic configuration succeeded. * Fail: The last automatic configuration failed. * Aborted: The last automatic configuration has been cancelled by the user. " ::= { autoConfigure 200 } -- End of group:Automatic Configuration -- **************************************************************************** -- Group:Notification Messages Configuration -- **************************************************************************** notificationsGroup OBJECT IDENTIFIER ::= { r2MIBObjects 60010 } -- Scalar:Minimal Severity of Notification minSeverity OBJECT-TYPE SYNTAX INTEGER { disable(0) , debug(100) , info(200) , warning(300) , error(400) , critical (500) } MAX-ACCESS read-write STATUS current DESCRIPTION " Minimal Severity of Notification Sets the minimal severity to issue a notification message incoming from this service. * Disable: No notification is issued. * Debug: All notification messages are issued. * Info: Notification messages with a 'Informational' and higher severity are issued. * Warning: Notification messages with a 'Warning' and higher severity are issued. * Error: Notification messages with an 'Error' and higher severity are issued. * Critical: Notification messages with a 'Critical' severity are issued. " DEFVAL { warning } ::= { notificationsGroup 100 } -- End of group:Notification Messages Configuration -- **************************************************************************** -- Group:Configuration Settings -- **************************************************************************** configurationGroup OBJECT IDENTIFIER ::= { r2MIBObjects 60020 } -- Scalar:Need Restart needRestartInfo OBJECT-TYPE SYNTAX INTEGER { no(0) , yes(100) } MAX-ACCESS read-only STATUS current DESCRIPTION " Need Restart Indicates if the service needs to be restarted for the configuration to fully take effect. * Yes: Service needs to be restarted. * No: Service does not need to be restarted. Services can be restarted by using the Scm.ServiceCommands.Restart command. " ::= { configurationGroup 100 } -- End of group:Configuration Settings END