-- **************************************************************************** -- **************************************************************************** -- Copyright(c) 2004 Mediatrix Telecom, Inc. -- NOTICE: -- This document contains information that is confidential and proprietary -- to Mediatrix Telecom, Inc. -- Mediatrix Telecom, Inc. reserves all rights to this document as well as -- to the Intellectual Property of the document and the technology and -- know-how that it includes and represents. -- This publication cannot be reproduced, neither in whole nor in part in -- any form whatsoever without written prior approval by -- Mediatrix Telecom, Inc. -- Mediatrix Telecom, Inc. reserves the right to revise this publication -- and make changes at any time and without the obligation to notify any -- person and/or entity of such revisions and/or changes. -- **************************************************************************** -- **************************************************************************** MX-NAT-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, Integer32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF MxEnableState, MxActivationState, MxIpHostName, MxIpAddress, MxIpPort, MxAdvancedIpPort, MxIpSubnetMask, MxDigitMap FROM MX-TC MxUInt64, MxFloat32, MxIpHostNamePort, MxIpAddr, MxIpAddrPort, MxIpAddrMask, MxUri, MxUrl FROM MX-TC2 mediatrixServices FROM MX-SMI2; natMIB MODULE-IDENTITY LAST-UPDATED "1910210000Z" ORGANIZATION " Mediatrix Telecom, Inc. " CONTACT-INFO " Mediatrix Telecom, Inc. 4229, Garlock Street Sherbrooke (Quebec) Canada Phone: (819) 829-8749 " DESCRIPTION " Network Address Translation The Network Address Translation (NAT) service allows the administrator to change the source or destination IP address of a packet. " ::= { mediatrixServices 2275 } natMIBObjects OBJECT IDENTIFIER ::= { natMIB 1 } -- Scalar:Configuration Modified Status configModifiedStatus OBJECT-TYPE SYNTAX INTEGER { yes(100) , no(200) } MAX-ACCESS read-only STATUS current DESCRIPTION " Configuration Modified Status Shows whether or not the Network Address Translation configuration has been modified without being applied. 1. Yes: The configuration has been modified but it has not been applied. 2. No: The Network Address Translation service uses the configured rules. Use the command Nat.ApplyConfig to apply the configuration. " ::= { natMIBObjects 100 } -- ***************************************************************************** -- Table:Source NAT Rules Status -- ***************************************************************************** sNatRulesStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF SNatRulesStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Source NAT Rules Status This table shows the rules applied in the source NAT. " ::= { natMIBObjects 200 } sNatRulesStatusEntry OBJECT-TYPE SYNTAX SNatRulesStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A row in table Source NAT Rules Status. " INDEX { sNatRulesStatusPriority } ::= { sNatRulesStatusTable 1 } SNatRulesStatusEntry ::= SEQUENCE { sNatRulesStatusPriority Unsigned32, sNatRulesStatusSourceAddress OCTET STRING, sNatRulesStatusSourcePort OCTET STRING, sNatRulesStatusDestinationAddress OCTET STRING, sNatRulesStatusDestinationPort OCTET STRING, sNatRulesStatusProtocol INTEGER, sNatRulesStatusNewAddress OCTET STRING } -- Index:Rule Priority sNatRulesStatusPriority OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " Rule Priority Unique identifier of the row in the table. " ::= { sNatRulesStatusEntry 100 } -- Columnar:Source Address sNatRulesStatusSourceAddress OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " Source Address Source address[/mask] criteria an incoming packet must have to match this rule. An empty string matches any address. " ::= { sNatRulesStatusEntry 200 } -- Columnar:Source Port sNatRulesStatusSourcePort OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " Source Port Source port[-port] criteria an incoming packet must have to match this rule. MinPort-MaxPort specifies a port range. An empty string means that no filtering is applied on the source port thus matching any port. This parameter is only effective when the SNatRulesStatus.Protocol parameter is set to Tcp or Udp. " ::= { sNatRulesStatusEntry 300 } -- Columnar:Destination Address sNatRulesStatusDestinationAddress OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " Destination Address Destination address[/mask] criteria an incoming packet must have to match this rule. An empty string matches any address. " ::= { sNatRulesStatusEntry 400 } -- Columnar:Destination Port sNatRulesStatusDestinationPort OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " Destination Port Destination port[-port] criteria an incoming packet must have to match this rule. MinPort-MaxPort specifies a port range. An empty string means that no filtering is applied on the destination port thus matching any port. This parameter is only effective when the SNatRulesStatus.Protocol parameter is set to Tcp or Udp. " ::= { sNatRulesStatusEntry 500 } -- Columnar:Protocol sNatRulesStatusProtocol OBJECT-TYPE SYNTAX INTEGER { all(100) , tcp(200) , udp(300) , icmp(400) } MAX-ACCESS read-only STATUS current DESCRIPTION " Protocol Protocol criteria an incoming packet must have to match this rule. The protocol can be one of the following: * All: Match packets using any protocol. * Tcp: Only match TCP packets. * Udp: Only match UDP packets. * Icmp: Only match ICMP packets. " ::= { sNatRulesStatusEntry 600 } -- Columnar:New Address sNatRulesStatusNewAddress OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " New Address New address[:port] applied to the source of the packet. When specifying a port number, it is mandatory to have the protocol set to TCP or UDP. " ::= { sNatRulesStatusEntry 700 } -- End of table:Source NAT Rules Status -- ***************************************************************************** -- Table:Source NAT Rules -- ***************************************************************************** sNatRulesTable OBJECT-TYPE SYNTAX SEQUENCE OF SNatRulesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Source NAT Rules This table shows the configured rules for source NAT. " ::= { natMIBObjects 700 } sNatRulesEntry OBJECT-TYPE SYNTAX SNatRulesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A row in table Source NAT Rules. " INDEX { sNatRulesPriority } ::= { sNatRulesTable 1 } SNatRulesEntry ::= SEQUENCE { sNatRulesPriority Unsigned32, sNatRulesActivation MxEnableState, sNatRulesSourceAddress OCTET STRING, sNatRulesSourcePort OCTET STRING, sNatRulesDestinationAddress OCTET STRING, sNatRulesDestinationPort OCTET STRING, sNatRulesProtocol INTEGER, sNatRulesNewAddress OCTET STRING, sNatRulesUp INTEGER, sNatRulesDown INTEGER, sNatRulesInsert INTEGER, sNatRulesDelete INTEGER } -- Index:Rule Priority sNatRulesPriority OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " Rule Priority Unique identifier of the row in the table. " ::= { sNatRulesEntry 100 } -- Row command:Down sNatRulesDown OBJECT-TYPE SYNTAX INTEGER { noOp(0), down(10) } MAX-ACCESS read-write STATUS current DESCRIPTION " Down Moves the current row downside. " DEFVAL { noOp } ::= { sNatRulesEntry 1000 } -- Row command:Insert sNatRulesInsert OBJECT-TYPE SYNTAX INTEGER { noOp(0), insert(10) } MAX-ACCESS read-write STATUS current DESCRIPTION " Insert Inserts a new row before this row. " DEFVAL { noOp } ::= { sNatRulesEntry 1100 } -- Row command:Delete sNatRulesDelete OBJECT-TYPE SYNTAX INTEGER { noOp(0), delete(10) } MAX-ACCESS read-write STATUS current DESCRIPTION " Delete Deletes this row. " DEFVAL { noOp } ::= { sNatRulesEntry 1200 } -- Columnar:Activation sNatRulesActivation OBJECT-TYPE SYNTAX MxEnableState MAX-ACCESS read-write STATUS current DESCRIPTION " Activation Activates this rule. * Enable: This rule is active in the SNAT. * Disable: This rule is not in the SNAT. " DEFVAL { disable } ::= { sNatRulesEntry 200 } -- Columnar:Source Address sNatRulesSourceAddress OBJECT-TYPE SYNTAX OCTET STRING ( SIZE(0..51) ) MAX-ACCESS read-write STATUS current DESCRIPTION " Source Address Source address of the incoming packet using the following format: address[/mask] or network interface name/. Address can be either a network IP address (using /mask) or one of the host IP addresses. When specifying a network interface name, it is mandatory to use the suffix '/'. Doing so indicates that the network address of this interface is used instead of the host address. Also, it must match one of the values in the parameter networkInterfacesStatusTable.InterfaceName from the Basic Network Interface (BNI) service. Note that if the specified network interface is disabled or removed, the rule is automatically disabled thus removed from the NAT. When the network interface is enabled or added back, the rule is automatically enabled and applied in the NAT. Mask must be a plain number specifying the number of binary 1s at the left side of the network mask. E.g.: a mask of 24 specifies a network mask of 255.255.255.0. Leaving the default empty string matches any address. " DEFVAL { "" } ::= { sNatRulesEntry 300 } -- Columnar:Source Port sNatRulesSourcePort OBJECT-TYPE SYNTAX OCTET STRING ( SIZE(0..11) ) MAX-ACCESS read-write STATUS current DESCRIPTION " Source Port Source port of the incoming packet using the following format: port[-port]. MinPort-MaxPort specifies a port range. The default empty string means that no filtering is applied on the source port thus matching any port. This parameter is only effective when the SNatRules.Protocol parameter is set to Tcp or Udp. " DEFVAL { "" } ::= { sNatRulesEntry 400 } -- Columnar:Destination Address sNatRulesDestinationAddress OBJECT-TYPE SYNTAX OCTET STRING ( SIZE(0..51) ) MAX-ACCESS read-write STATUS current DESCRIPTION " Destination Address Destination address of the incoming packet using the following format: address[/mask] or network interface name/. Address can be either a network IP address (using /mask) or one of the host IP addresses. When specifying a network interface name, it is mandatory to use the suffix '/'. Doing so indicates that the network address of this interface is used instead of the host address. Also, it must match one of the values in the parameter networkInterfacesStatusTable.InterfaceName from the Basic Network Interface (BNI) service. Note that if the specified network interface is disabled or removed, the rule is automatically disabled thus removed from the NAT. When the network interface is enabled or added back, the rule is automatically enabled and applied in the NAT. Mask must be a plain number specifying the number of binary 1s at the left side of the network mask. E.g.: a mask of 24 specifies a network mask of 255.255.255.0. Leaving the default empty string matches any address. " DEFVAL { "" } ::= { sNatRulesEntry 500 } -- Columnar:Destination Port sNatRulesDestinationPort OBJECT-TYPE SYNTAX OCTET STRING ( SIZE(0..11) ) MAX-ACCESS read-write STATUS current DESCRIPTION " Destination Port Destination port of the incoming packet using the following format: port[-port]. MinPort-MaxPort specifies a port range. The default empty string means that no filtering is applied on the destination port thus matching any port. This parameter is only effective when the SNatRules.Protocol parameter is set to Tcp or Udp. " DEFVAL { "" } ::= { sNatRulesEntry 600 } -- Columnar:Protocol sNatRulesProtocol OBJECT-TYPE SYNTAX INTEGER { all(100) , tcp(200) , udp(300) , icmp(400) } MAX-ACCESS read-write STATUS current DESCRIPTION " Protocol Protocol of the incoming packet. The protocol can be one of the following: * All: Match packets using any protocol. * Tcp: Only match TCP packets. * Udp: Only match UDP packets. * Icmp: Only match ICMP packets. " DEFVAL { all } ::= { sNatRulesEntry 700 } -- Columnar:New Address sNatRulesNewAddress OBJECT-TYPE SYNTAX OCTET STRING ( SIZE(0..51) ) MAX-ACCESS read-write STATUS current DESCRIPTION " New Address New address applied to the source of the packet using the following syntax: address[:port]. When specifying a port number, it is mandatory to have the protocol set to TCP or UDP. " DEFVAL { "" } ::= { sNatRulesEntry 800 } -- Row command:Up sNatRulesUp OBJECT-TYPE SYNTAX INTEGER { noOp(0), up(10) } MAX-ACCESS read-write STATUS current DESCRIPTION " Up Moves the current row upside. " DEFVAL { noOp } ::= { sNatRulesEntry 900 } -- End of table:Source NAT Rules -- ***************************************************************************** -- Table:Destination NAT Rules Status -- ***************************************************************************** dNatRulesStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF DNatRulesStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Destination NAT Rules Status This table shows the rules applied in the destination NAT. " ::= { natMIBObjects 800 } dNatRulesStatusEntry OBJECT-TYPE SYNTAX DNatRulesStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A row in table Destination NAT Rules Status. " INDEX { dNatRulesStatusPriority } ::= { dNatRulesStatusTable 1 } DNatRulesStatusEntry ::= SEQUENCE { dNatRulesStatusPriority Unsigned32, dNatRulesStatusSourceAddress OCTET STRING, dNatRulesStatusSourcePort OCTET STRING, dNatRulesStatusDestinationAddress OCTET STRING, dNatRulesStatusDestinationPort OCTET STRING, dNatRulesStatusProtocol INTEGER, dNatRulesStatusNewAddress OCTET STRING } -- Index:Rule Priority dNatRulesStatusPriority OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " Rule Priority Unique identifier of the row in the table. " ::= { dNatRulesStatusEntry 100 } -- Columnar:Source Address dNatRulesStatusSourceAddress OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " Source Address Source address[/mask] criteria an incoming packet must have to match this rule. An empty string matches any address. " ::= { dNatRulesStatusEntry 200 } -- Columnar:Source Port dNatRulesStatusSourcePort OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " Source Port Source port[-port] criteria an incoming packet must have to match this rule. MinPort-MaxPort specifies a port range. An empty string means that no filtering is applied on the source port thus matching any port. This parameter is only effective when the DNatRulesStatus.Protocol parameter is set to Tcp or Udp. " ::= { dNatRulesStatusEntry 300 } -- Columnar:Destination Address dNatRulesStatusDestinationAddress OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " Destination Address Destination address[/mask] criteria an incoming packet must have to match this rule. An empty string matches any address. " ::= { dNatRulesStatusEntry 400 } -- Columnar:Destination Port dNatRulesStatusDestinationPort OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " Destination Port Destination port[-port] criteria an incoming packet must have to match this rule. MinPort-MaxPort specifies a port range. An empty string means that no filtering is applied on the destination port thus matching any port. This parameter is only effective when the DNatRulesStatus.Protocol parameter is set to Tcp or Udp. " ::= { dNatRulesStatusEntry 500 } -- Columnar:Protocol dNatRulesStatusProtocol OBJECT-TYPE SYNTAX INTEGER { all(100) , tcp(200) , udp(300) , icmp(400) } MAX-ACCESS read-only STATUS current DESCRIPTION " Protocol Protocol criteria an incoming packet must have to match this rule. The protocol can be one of the following: * All: Match packets using any protocol. * Tcp: Only match TCP packets. * Udp: Only match UDP packets. * Icmp: Only match ICMP packets. " ::= { dNatRulesStatusEntry 600 } -- Columnar:New Address dNatRulesStatusNewAddress OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION " New Address New address[:port] applied to the destination of the packet. When specifying a port number, it is mandatory to have the protocol set to TCP or UDP. " ::= { dNatRulesStatusEntry 700 } -- End of table:Destination NAT Rules Status -- ***************************************************************************** -- Table:Destination NAT Rules -- ***************************************************************************** dNatRulesTable OBJECT-TYPE SYNTAX SEQUENCE OF DNatRulesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Destination NAT Rules This table shows the configured rules for destination NAT. " ::= { natMIBObjects 900 } dNatRulesEntry OBJECT-TYPE SYNTAX DNatRulesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A row in table Destination NAT Rules. " INDEX { dNatRulesPriority } ::= { dNatRulesTable 1 } DNatRulesEntry ::= SEQUENCE { dNatRulesPriority Unsigned32, dNatRulesActivation MxEnableState, dNatRulesSourceAddress OCTET STRING, dNatRulesSourcePort OCTET STRING, dNatRulesDestinationAddress OCTET STRING, dNatRulesDestinationPort OCTET STRING, dNatRulesProtocol INTEGER, dNatRulesNewAddress OCTET STRING, dNatRulesUp INTEGER, dNatRulesDown INTEGER, dNatRulesInsert INTEGER, dNatRulesDelete INTEGER } -- Index:Rule Priority dNatRulesPriority OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " Rule Priority Unique identifier of the row in the table. " ::= { dNatRulesEntry 100 } -- Row command:Down dNatRulesDown OBJECT-TYPE SYNTAX INTEGER { noOp(0), down(10) } MAX-ACCESS read-write STATUS current DESCRIPTION " Down Moves the current row downside. " DEFVAL { noOp } ::= { dNatRulesEntry 1000 } -- Row command:Insert dNatRulesInsert OBJECT-TYPE SYNTAX INTEGER { noOp(0), insert(10) } MAX-ACCESS read-write STATUS current DESCRIPTION " Insert Inserts a new row before this row. " DEFVAL { noOp } ::= { dNatRulesEntry 1100 } -- Row command:Delete dNatRulesDelete OBJECT-TYPE SYNTAX INTEGER { noOp(0), delete(10) } MAX-ACCESS read-write STATUS current DESCRIPTION " Delete Deletes this row. " DEFVAL { noOp } ::= { dNatRulesEntry 1200 } -- Columnar:State dNatRulesActivation OBJECT-TYPE SYNTAX MxEnableState MAX-ACCESS read-write STATUS current DESCRIPTION " State Activations this rule. * Enable: This rule is active in the DNAT. * Disable: This rule is not in the DNAT. " DEFVAL { disable } ::= { dNatRulesEntry 200 } -- Columnar:Source Address dNatRulesSourceAddress OBJECT-TYPE SYNTAX OCTET STRING ( SIZE(0..51) ) MAX-ACCESS read-write STATUS current DESCRIPTION " Source Address Source address of the incoming packet using the following format: address[/mask] or network interface name/. Address can be either a network IP address (using /mask) or one of the host IP addresses. When specifying a network interface name, it is mandatory to use the suffix '/'. Doing so indicates that the network address of this interface is used instead of the host address. Also, it must match one of the values in the parameter networkInterfacesStatusTable.InterfaceName from the Basic Network Interface (BNI) service. Note that if the specified network interface is disabled or removed, the rule is automatically disabled thus removed from the NAT. When the network interface is enabled or added back, the rule is automatically enabled and applied in the NAT. Mask must be a plain number specifying the number of binary 1s at the left side of the network mask. E.g.: a mask of 24 specifies a network mask of 255.255.255.0. Leaving the default empty string matches any address. " DEFVAL { "" } ::= { dNatRulesEntry 300 } -- Columnar:Source Port dNatRulesSourcePort OBJECT-TYPE SYNTAX OCTET STRING ( SIZE(0..11) ) MAX-ACCESS read-write STATUS current DESCRIPTION " Source Port Source port of the incoming packet using the following format: port[-port]. MinPort-MaxPort specifies a port range. The default empty string means that no filtering is applied on the source port thus matching any port. This parameter is only effective when the DNatRules.Protocol parameter is set to Tcp or Udp. " DEFVAL { "" } ::= { dNatRulesEntry 400 } -- Columnar:Destination Address dNatRulesDestinationAddress OBJECT-TYPE SYNTAX OCTET STRING ( SIZE(0..51) ) MAX-ACCESS read-write STATUS current DESCRIPTION " Destination Address Destination address of the incoming packet using the following format: address[/mask] or network interface name/. Address can be either a network IP address (using /mask) or one of the host IP addresses. When specifying a network interface name, it is mandatory to use the suffix '/'. Doing so indicates that the network address of this interface is used instead of the host address. Also, it must match one of the values in the parameter networkInterfacesStatusTable.InterfaceName from the Basic Network Interface (BNI) service. Note that if the specified network interface is disabled or removed, the rule is automatically disabled thus removed from the NAT. When the network interface is enabled or added back, the rule is automatically enabled and applied in the NAT. Mask must be a plain number specifying the number of binary 1s at the left side of the network mask. E.g.: a mask of 24 specifies a network mask of 255.255.255.0. Leaving the default empty string matches any address. " DEFVAL { "" } ::= { dNatRulesEntry 500 } -- Columnar:Destination Port dNatRulesDestinationPort OBJECT-TYPE SYNTAX OCTET STRING ( SIZE(0..11) ) MAX-ACCESS read-write STATUS current DESCRIPTION " Destination Port Destination port of the incoming packet using the following format: port[-port]. MinPort-MaxPort specifies a port range. The default empty string means that no filtering is applied on the destination port thus matching any port. This parameter is only effective when the DNatRules.Protocol parameter is set to Tcp or Udp. " DEFVAL { "" } ::= { dNatRulesEntry 600 } -- Columnar:Protocol dNatRulesProtocol OBJECT-TYPE SYNTAX INTEGER { all(100) , tcp(200) , udp(300) , icmp(400) } MAX-ACCESS read-write STATUS current DESCRIPTION " Protocol Protocol of the incoming packet. The protocol can be one of the following: * All: Match packets using any protocol. * Tcp: Only match TCP packets. * Udp: Only match UDP packets. * Icmp: Only match ICMP packets. " DEFVAL { all } ::= { dNatRulesEntry 700 } -- Columnar:New Address dNatRulesNewAddress OBJECT-TYPE SYNTAX OCTET STRING ( SIZE(0..51) ) MAX-ACCESS read-write STATUS current DESCRIPTION " New Address New address applied to the destination of the packet using the following syntax: address[:port]. When specifying a port number, it is mandatory to have the protocol set to TCP or UDP. " DEFVAL { "" } ::= { dNatRulesEntry 800 } -- Row command:Up dNatRulesUp OBJECT-TYPE SYNTAX INTEGER { noOp(0), up(10) } MAX-ACCESS read-write STATUS current DESCRIPTION " Up Moves the current row upside. " DEFVAL { noOp } ::= { dNatRulesEntry 900 } -- End of table:Destination NAT Rules -- **************************************************************************** -- Group:Notification Messages Configuration -- **************************************************************************** notificationsGroup OBJECT IDENTIFIER ::= { natMIBObjects 60010 } -- Scalar:Minimal Severity of Notification minSeverity OBJECT-TYPE SYNTAX INTEGER { disable(0) , debug(100) , info(200) , warning(300) , error(400) , critical (500) } MAX-ACCESS read-write STATUS current DESCRIPTION " Minimal Severity of Notification Sets the minimal severity to issue a notification message incoming from this service. * Disable: No notification is issued. * Debug: All notification messages are issued. * Info: Notification messages with a 'Informational' and higher severity are issued. * Warning: Notification messages with a 'Warning' and higher severity are issued. * Error: Notification messages with an 'Error' and higher severity are issued. * Critical: Notification messages with a 'Critical' severity are issued. " DEFVAL { warning } ::= { notificationsGroup 100 } -- End of group:Notification Messages Configuration -- **************************************************************************** -- Group:Configuration Settings -- **************************************************************************** configurationGroup OBJECT IDENTIFIER ::= { natMIBObjects 60020 } -- Scalar:Need Restart needRestartInfo OBJECT-TYPE SYNTAX INTEGER { no(0) , yes(100) } MAX-ACCESS read-only STATUS current DESCRIPTION " Need Restart Indicates if the service needs to be restarted for the configuration to fully take effect. * Yes: Service needs to be restarted. * No: Service does not need to be restarted. Services can be restarted by using the Scm.ServiceCommands.Restart command. " ::= { configurationGroup 100 } -- End of group:Configuration Settings END