-- QLOGIC-MIB.my: QLogic Object Identifier Assignments -- -- Copyright (c) 1994-2009 QLogic Corporation. -- All Rights Reserved QLOGIC-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, enterprises, Integer32, Counter32, Unsigned32 FROM SNMPv2-SMI connUnitId FROM FCMGMT-MIB ancorOidTree FROM QLOGIC-SMI TEXTUAL-CONVENTION FROM SNMPv2-TC; ancorPortModule MODULE-IDENTITY LAST-UPDATED "200909290000Z" -- September 29, 2009 ORGANIZATION "QLOGIC Corporation" CONTACT-INFO "QLOGIC Technical Support Postal: QLogic Corporation 6321 Bury Drive Eden Prairie, MN 55346 US Tel: +1 952 932 4040 Fax: +1 952 932 4018 E-mail: support@QLogic.com" DESCRIPTION "This table replaces the fcFxPortPhysTable module defined in FIBRE-CHANNEL-FE-MIB. It defines volatile control objects for ports in a QLogic SANbox switch." REVISION "200909290000Z" -- September 29, 2009 DESCRIPTION "The syntax and semantics errors reported by the smilint program were resolved." REVISION "200610110000Z" -- October 11, 2006 DESCRIPTION "Changed module identity from qlogic to ancor to remove conflicts with existing definitions in the QLOGIC-SMI. Commented out duplicate definitions of fcQxPortOperMode and fcQxPortAdminMode that overlap with fcQxQuailPortOperMode and fcQxQuailPortAdminMode." ::= { ancorOidTree 3 } qlSB2PortControl OBJECT IDENTIFIER ::= { ancorPortModule 10 } qlSB2PortStatus OBJECT IDENTIFIER ::= { ancorPortModule 11 } FcQlModuleIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Represents the module index within a conceptual table." SYNTAX Unsigned32 FcQxPortIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Represents the Port index within a conceptual table." SYNTAX Unsigned32 ------------------------------------------------------------------------------ -- Port Control group -- the QxPort Physical Level table -- This table contains, one entry for each QxPort in the -- Fabric Element, the physical level status and parameters -- of the QxPorts. fcQxPortPhysTable OBJECT-TYPE SYNTAX SEQUENCE OF FcQxPortPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains, one entry for each QxPort in the Fabric Element, physical level status and parameters of the QxPorts." ::= { qlSB2PortControl 1 } fcQxPortPhysEntry OBJECT-TYPE SYNTAX FcQxPortPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing physical level status and parameters of a QxPort." INDEX { fcQxPortPhysModule, fcQxPortPhysIndex } ::= { fcQxPortPhysTable 1 } FcQxPortPhysEntry ::= SEQUENCE { fcQxPortPhysModule FcQlModuleIndex, fcQxPortPhysIndex FcQxPortIndex, fcQxPortPhysAdminStatus INTEGER, fcQxPortPhysOperStatus INTEGER, fcQxQuailPortPhysAdminStatus INTEGER, fcQxQuailPortPhysOperStatus INTEGER, fcQxQuailPortPhysReasonCode INTEGER } fcQxPortPhysModule OBJECT-TYPE SYNTAX FcQlModuleIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the module within the Fabric Element for which this entry contains information. This value is never greater than fcFeModuleCapacity." ::= { fcQxPortPhysEntry 1 } fcQxPortPhysIndex OBJECT-TYPE SYNTAX FcQxPortIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the QxPort within the module. This number ranges from 1 to the value of fcFeModulePortCapacity for the associated module. The value remains constant for the identified QxPort until the module is re-initialized." ::= { fcQxPortPhysEntry 2 } fcQxPortPhysAdminStatus OBJECT-TYPE SYNTAX INTEGER { online (1), -- place port online offline (2), -- take port offline testing (3) -- initiate test procedures } MAX-ACCESS read-write STATUS current DESCRIPTION "The desired state of the QxPort. A management station may place the QxPort in a desired state by setting this object accordingly. The testing(3) state indicates that no operational frames can be passed. When a Fabric Element initializes, all QxPorts start with fcQxPortPhysAdminStatus in the offline(2) state. As the result of either explicit management action or per configuration information accessible by the Fabric Element, fcQxPortPhysAdminStatus is then changed to either the online(1) or testing(3) states, or remains in the offline state." ::= { fcQxPortPhysEntry 3 } fcQxPortPhysOperStatus OBJECT-TYPE SYNTAX INTEGER { online (1), -- Login may proceed offline (2), -- Login cannot proceed testing (3), -- port is under test linkFailure (4) -- failure after online/testing } MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational status of the QxPort. The testing(3) indicates that no operational frames can be passed. If fcQxPortPhysAdminStatus is offline(2) then fcQxPortPhysOperStatus should be offline(2). If fcQxPortPhysAdminStatus is changed to online(1) then fcQxPortPhysOperStatus should change to online(1) if the QxPort is ready to accept Fabric Login request from the attached NxPort; it should proceed and remain in the link- failure(4) state if and only if there is a fault that prevents it from going to the online(1) state." ::= { fcQxPortPhysEntry 4 } fcQxQuailPortPhysAdminStatus OBJECT-TYPE SYNTAX INTEGER { up (1), -- place port online down (2) -- take port offline } MAX-ACCESS read-write STATUS current DESCRIPTION "The desired state of the port." ::= { fcQxPortPhysEntry 5 } fcQxQuailPortPhysOperStatus OBJECT-TYPE SYNTAX INTEGER { up (1), -- online down (2) -- offline } MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational status of the QxPort." ::= { fcQxPortPhysEntry 6 } fcQxQuailPortPhysReasonCode OBJECT-TYPE SYNTAX INTEGER { unknown (1), -- Unknown up (2), -- None down (3), -- Administratively down notConnected (4), -- Link failure or not connected sfpAbsent (5), -- SFP not present sfpUnsupported (6), -- Unknown SFP hardwareFailure (7), -- Hardware failure isolated (8) -- Isolated } MAX-ACCESS read-only STATUS current DESCRIPTION "The reason for the current operational status of the port. If the status is 'up', this will be 'up'. If the status is 'down', the reason code will indicate the reason, e.g. 'isolated', 'sfpAbsent', etc." ::= { fcQxPortPhysEntry 7 } ------------------------------------------------------------------------------ -- the Status group -- This group consists of tables that contains operational -- status and established service parameters for the Fabric -- Element and the attached NxPorts. -- The QxPort Status table -- This table contains, one entry for each QxPort, -- the operational status and parameters of the FxPorts. fcQxPortStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF FcQxPortStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains, one entry for each QxPort in the Fabric Element, operational status and parameters of the QxPorts." ::= { qlSB2PortStatus 1 } fcQxPortStatusEntry OBJECT-TYPE SYNTAX FcQxPortStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing operational status and parameters of a QxPort." INDEX { fcQxPortStatusModule, fcQxPortStatusIndex } ::= { fcQxPortStatusTable 1 } FcQxPortStatusEntry ::= SEQUENCE { fcQxPortStatusModule FcQlModuleIndex, fcQxPortStatusIndex FcQxPortIndex, -- fcQxPortOperMode -- INTEGER, -- fcQxPortAdminMode -- INTEGER fcQxQuailPortOperMode INTEGER, fcQxQuailPortAdminMode INTEGER } fcQxPortStatusModule OBJECT-TYPE SYNTAX FcQlModuleIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the module within the Fabric Element for which this entry contains information. This value is never greater than fcFeModuleCapacity." ::= { fcQxPortStatusEntry 1 } fcQxPortStatusIndex OBJECT-TYPE SYNTAX FcQxPortIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the QxPort within the module. This number ranges from 1 to the value of fcFeModulePortCapacity for the associated module. The value remains constant for the identified QxPort until the module is re-initialized." ::= { fcQxPortStatusEntry 2 } -- fcQxPortOperMode OBJECT-TYPE -- SYNTAX INTEGER { -- glPort (1), -- fPort (2), -- lPort (3), -- ePort (4), -- flPort (6) -- } -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The current operational mode of the FxPort." -- ::= { fcQxPortStatusEntry 3 } -- fcQxPortAdminMode OBJECT-TYPE -- SYNTAX INTEGER { -- glPort (1), -- fPort (2), -- lPort (3), -- ePort (4), -- flPort (6) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The desired operational mode of the FxPort." -- ::= { fcQxPortStatusEntry 4 } fcQxQuailPortOperMode OBJECT-TYPE SYNTAX INTEGER { auto (1), fPort (2), flPort (3), ePort (4), fxPort (6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational mode of the FxPort." ::= { fcQxPortStatusEntry 3 } fcQxQuailPortAdminMode OBJECT-TYPE SYNTAX INTEGER { auto (1), fPort (2), flPort (3), ePort (4), fxPort (6) } MAX-ACCESS read-write STATUS current DESCRIPTION "The desired operational mode of the FxPort." ::= { fcQxPortStatusEntry 4 } ------------------------------------------------------------------------------ -- Related traps qlSB2PortLinkDown NOTIFICATION-TYPE OBJECTS { fcQxPortPhysAdminStatus, fcQxPortPhysOperStatus } STATUS current DESCRIPTION "A linkDown trap signifies that the SNMP entity, acting in an agent role, has detected that the fcQxPortPhysOperStatus object for one of its communication links has left the online state and transitioned to some other state. The current state is indicated by the included value of fcQxPortPhysOperStatus." ::= { ancorPortModule 0 10 } qlSB2PortLinkUp NOTIFICATION-TYPE OBJECTS { fcQxPortPhysAdminStatus, fcQxPortPhysOperStatus } STATUS current DESCRIPTION "A linkUp trap signifies that the SNMP entity, acting in an agent role, has detected that the fcQxPortPhysOperStatus object for one of its communication links has entered the online state from some other state. The current state is indicated by the included value of fcQxPortPhysOperStatus." ::= { ancorPortModule 0 11 } qlconnUnitAddedTrap NOTIFICATION-TYPE OBJECTS { connUnitId } STATUS current DESCRIPTION "A connUnit has been added to this agent. This is a suppliment to the FCMGMT-MIB which only defines a connUnitDeletedTrap" ::= { ancorPortModule 0 12 } END -- End of Object Definitions