-- -- ISKRATEL-MSAN-MIB.mib -- MIB generated by MG-SOFT Visual MIB Builder Version 7.0 Build 240 -- Tuesday, April 02, 2013 at 11:58:38 -- ISKRATEL-MSAN-MIB DEFINITIONS ::= BEGIN IMPORTS dot1dBasePort FROM BRIDGE-MIB ifIndex, InterfaceIndex FROM IF-MIB InetAddressType, InetAddress, InetAddressIPv6, InetAddressIPv4 FROM INET-ADDRESS-MIB dot1qVlanIndex, VlanIndex FROM Q-BRIDGE-MIB enterprises FROM RFC1155-SMI DisplayString FROM RFC1213-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB TimeTicks, IpAddress, Integer32, Unsigned32, Gauge32, Counter32, BITS, OBJECT-TYPE, MODULE-IDENTITY FROM SNMPv2-SMI RowStatus, MacAddress, TruthValue, TEXTUAL-CONVENTION FROM SNMPv2-TC vdslLineConfProfileName FROM VDSL-LINE-MIB xdsl2LineConfTemplateEntry, xdsl2LineAlarmConfTemplateEntry FROM VDSL2-LINE-MIB; -- 1.3.6.1.4.1.1332.1.1.5 msan MODULE-IDENTITY LAST-UPDATED "201006221233Z" -- June 22, 2010 at 12:33 GMT ORGANIZATION "Iskratel" CONTACT-INFO "Contact-info." DESCRIPTION "Description." ::= { products 5 } -- -- Textual conventions -- VlanList ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 1 through 8, the second octet specifying vlans 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered vlan, and the least significant bit represents the highest numbered vlan. Thus, each vlan supported is represented by a single bit within the value of this object. If that bit has a value of '1' then the associated port is in that vlan; the port is not included if the vlans bit has a value of '0'." SYNTAX OCTET STRING Xdsl2PsdMaskDs ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This is a structure that represents up to 32 PSD mask breakpoints. Each breakpoint occupies 3 octets: The first two octets hold the index of the subcarrier associated with the breakpoint. The third octet holds the PSD reduction at the breakpoint from 0 (0 dBm/Hz) to 255 (-127.5 dBm/Hz) using units of 0.5 dBm/Hz. The subcarrier index is an unsigned number in the range 0 to NSCds-1." SYNTAX OCTET STRING (SIZE (0..96)) Xdsl2PsdMaskUs ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This is a structure that represents up to 16 PSD mask breakpoints. Each breakpoint occupies 3 octets: The first two octets hold the index of the subcarrier associated with the breakpoint. The third octet holds the PSD reduction at the breakpoint from 0(0 dBm/Hz) to 255 (-127.5 dBm/Hz) using units of 0.5 dBm/Hz. The subcarrier index is an unsigned number in the range 0 to NSCus-1." SYNTAX OCTET STRING (SIZE (0..48)) PortMask ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0' When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Configuration of any port numbers between this range that are not valid ports return a failure message, but will still apply configuration for valid ports." SYNTAX OCTET STRING PercentByFives ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An unsigned integer representing a value expressed as a percentage with five percent increments." SYNTAX Unsigned32 (0 | 5 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 | 50 | 55 | 60 | 65 | 70 | 75 | 80 | 85 | 90 | 95 | 100) -- -- Node definitions -- -- 1.3.6.1.4.1.1332 iskratel OBJECT IDENTIFIER ::= { enterprises 1332 } -- 1.3.6.1.4.1.1332.1 si2000 OBJECT IDENTIFIER ::= { iskratel 1 } -- 1.3.6.1.4.1.1332.1.1 products OBJECT IDENTIFIER ::= { si2000 1 } -- 1.3.6.1.4.1.1332.1.1.5.1 msanInfo OBJECT IDENTIFIER ::= { msan 1 } -- 1.3.6.1.4.1.1332.1.1.5.1.1 msanShelfInfo OBJECT IDENTIFIER ::= { msanInfo 1 } -- 1.3.6.1.4.1.1332.1.1.5.1.1.1 msanShelfId OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "MSAN shelf ID." ::= { msanShelfInfo 1 } -- 1.3.6.1.4.1.1332.1.1.5.1.1.2 msanShelfType OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "MSAN shelf type." ::= { msanShelfInfo 2 } -- 1.3.6.1.4.1.1332.1.1.5.1.1.3 msanShelfSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Size of MSAN shelf (in number of slots)." ::= { msanShelfInfo 3 } -- 1.3.6.1.4.1.1332.1.1.5.1.2 msanBoardInfo OBJECT IDENTIFIER ::= { msanInfo 2 } -- 1.3.6.1.4.1.1332.1.1.5.1.2.1 msanBoardTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanBoardEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." ::= { msanBoardInfo 1 } -- 1.3.6.1.4.1.1332.1.1.5.1.2.1.1 msanBoardEntry OBJECT-TYPE SYNTAX MsanBoardEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." INDEX { msanBoardNr } ::= { msanBoardTable 1 } MsanBoardEntry ::= SEQUENCE { msanBoardNr INTEGER, msanBoardParentNr INTEGER, msanBoardPosition INTEGER, msanBoardType OCTET STRING, msanBoardId OCTET STRING, msanBoardSerialNr OCTET STRING, msanBoardDescription OCTET STRING } -- 1.3.6.1.4.1.1332.1.1.5.1.2.1.1.1 msanBoardNr OBJECT-TYPE SYNTAX INTEGER (1..1000) MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Unique identification of a board." ::= { msanBoardEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.1.2.1.1.2 msanBoardParentNr OBJECT-TYPE SYNTAX INTEGER (1..1000) MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Unique identification of a parent board." ::= { msanBoardEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.1.2.1.1.3 msanBoardPosition OBJECT-TYPE SYNTAX INTEGER (1..1000) MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Position of the board on the parent board." ::= { msanBoardEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.1.2.1.1.4 msanBoardType OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Type of physical board (e.g. IDC, SGO, SFA, ...)" ::= { msanBoardEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.1.2.1.1.5 msanBoardId OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Name (actual identification) of a board." ::= { msanBoardEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.1.2.1.1.6 msanBoardSerialNr OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Serial number of a board." ::= { msanBoardEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.1.2.1.1.7 msanBoardDescription OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Description of the board." ::= { msanBoardEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.1.3 msanSwInfo OBJECT IDENTIFIER ::= { msanInfo 3 } -- 1.3.6.1.4.1.1332.1.1.5.1.3.1 msanSwSteerVersion OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The unique steer code for this software. " ::= { msanSwInfo 1 } -- 1.3.6.1.4.1.1332.1.1.5.1.3.2 msanSwBuildDirectory OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The directory where software was build on. " ::= { msanSwInfo 2 } -- 1.3.6.1.4.1.1332.1.1.5.1.3.3 msanSwBuildTime OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The time when the software was built. (DateAndTime textual convention, from SNMPv2-TC)" ::= { msanSwInfo 3 } -- 1.3.6.1.4.1.1332.1.1.5.1.3.4 msanSwBranch OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The repository branch where the software was built from." ::= { msanSwInfo 4 } -- 1.3.6.1.4.1.1332.1.1.5.1.3.5 msanSwBuildReference OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The repository reference number of the software build branch. " ::= { msanSwInfo 5 } -- 1.3.6.1.4.1.1332.1.1.5.1.3.6 msanSwILVersion OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The unique IL steer code for this software. " ::= { msanSwInfo 6 } -- 1.3.6.1.4.1.1332.1.1.5.1.3.7 msanSwIpmiVersion OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The major version.minor version/IPMI version supported(HEX) number of the IPMI currently running on the switch. For example, if the major version was 1 and the minor version was 2, the format would be '1.2/0'." ::= { msanSwInfo 7 } -- 1.3.6.1.4.1.1332.1.1.5.1.3.8 msanSwBspVersion OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The release.version/id number of the BSP software currently running on the switch. For example, if the release was 1 and the version was 2, the format would be '1.2/0'." ::= { msanSwInfo 8 } -- 1.3.6.1.4.1.1332.1.1.5.1.3.9 msanSwCPLDVersion OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "CPLD (Complex Programmable Logic Device) SW version" ::= { msanSwInfo 9 } -- 1.3.6.1.4.1.1332.1.1.5.1.3.10 msanReservePackage OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Name of the reserve package on disk if it exists. " ::= { msanSwInfo 10 } -- 1.3.6.1.4.1.1332.1.1.5.1.3.11 msanSwComponentTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanSwComponentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanSwInfo 11 } -- 1.3.6.1.4.1.1332.1.1.5.1.3.11.1 msanSwComponentEntry OBJECT-TYPE SYNTAX MsanSwComponentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanSwComponentId } ::= { msanSwComponentTable 1 } MsanSwComponentEntry ::= SEQUENCE { msanSwComponentId Integer32, msanSwComponentName OCTET STRING, msanSwComponentSteerVersion OCTET STRING } -- 1.3.6.1.4.1.1332.1.1.5.1.3.11.1.1 msanSwComponentId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Unique index of SW component." ::= { msanSwComponentEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.1.3.11.1.2 msanSwComponentName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Name of software component (e.g. ES, EV, EF, EA)." ::= { msanSwComponentEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.1.3.11.1.3 msanSwComponentSteerVersion OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The unique steer code for this software component." ::= { msanSwComponentEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.1.4 msanOtherInfo OBJECT IDENTIFIER ::= { msanInfo 4 } -- 1.3.6.1.4.1.1332.1.1.5.1.4.1 msanSnmpSetErrorReason OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Last error description of SNMP set command." DEFVAL { "" } ::= { msanOtherInfo 1 } -- 1.3.6.1.4.1.1332.1.1.5.3 msanAdditionalConf OBJECT IDENTIFIER ::= { msan 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.1 msanSystem OBJECT IDENTIFIER ::= { msanAdditionalConf 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.1 msanDateTime OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Board date and time in format: dd/MM/yyyy HH:mm:ss." ::= { msanSystem 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.2 msanShelfIdConf OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "MSAN Shelf ID." ::= { msanSystem 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.3 msanConfData OBJECT-TYPE SYNTAX INTEGER { saved(1), notSaved(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Configured data saved or not saved to file on local file system." ::= { msanSystem 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.4 msanSwUpgrade OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS deprecated DESCRIPTION "msanSWUpgrade parameetr is used to start SW upgrade from external http or ftp server. User must set the next string value: = http|ftp://|[:]/[/] Procedure uses anonymous type of identification. If a non standard port is used, this port must be also specified in the repository URL." ::= { msanSystem 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.5 msanCliScriptCreate OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "When set with a non-empty string, current configuration will be saved to script file with that name (name must end with .scr). If file already exists it's overwritten. On Get request this object will always return an empty string." ::= { msanSystem 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.6 msanCliScriptTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanCliScriptEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanSystem 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.6.1 msanCliScriptEntry OBJECT-TYPE SYNTAX MsanCliScriptEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanCliScriptName } ::= { msanCliScriptTable 1 } MsanCliScriptEntry ::= SEQUENCE { msanCliScriptName OCTET STRING, msanCliScriptApply INTEGER, msanCliScriptApplyStatus INTEGER, msanCliScriptRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.1.6.1.1 msanCliScriptName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "CLI script name" ::= { msanCliScriptEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.6.1.2 msanCliScriptApply OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When set to enable(1) selected selected CLI script is applied." ::= { msanCliScriptEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.6.1.3 msanCliScriptApplyStatus OBJECT-TYPE SYNTAX INTEGER { notInitiated(1), inProcess(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status of CLI script apply request" ::= { msanCliScriptEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.6.1.4 msanCliScriptRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanCliScriptEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.7 msanCliPrompt OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "CLI prompt value." ::= { msanSystem 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.8 msanChassisId OBJECT-TYPE SYNTAX Integer32 (1..99) MAX-ACCESS read-write STATUS current DESCRIPTION "MSAN Chassis ID." ::= { msanSystem 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.9 msanSwBootPackageTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanSwBootPackageEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanSystem 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.9.1 msanSwBootPackageEntry OBJECT-TYPE SYNTAX MsanSwBootPackageEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanSwBootPackageName } ::= { msanSwBootPackageTable 1 } MsanSwBootPackageEntry ::= SEQUENCE { msanSwBootPackageName DisplayString, msanSwBootPackageStatus INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.1.9.1.1 msanSwBootPackageName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "SW package name on local disk." ::= { msanSwBootPackageEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.9.1.2 msanSwBootPackageStatus OBJECT-TYPE SYNTAX INTEGER { currentActive(1), nextActive(2), backup(3), none(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "SW package status. You can set only nextActive(2) value. Other values are read-only." ::= { msanSwBootPackageEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.10 msanSystemSwUpgrade OBJECT IDENTIFIER ::= { msanSystem 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.10.1 msanSystemSwUpgradeStart OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Control of SW upgrade procedure. When set to enable(1) transfer of SW package from defined server is started." DEFVAL { disable } ::= { msanSystemSwUpgrade 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.10.2 msanSystemSwUpgradeStatus OBJECT-TYPE SYNTAX INTEGER { inprogress(1), successful(2), failed(3), notInitiated(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The SW upgrade status info." DEFVAL { notInitiated } ::= { msanSystemSwUpgrade 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.10.3 msanSystemSwUpgradeServerIpAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the type of the upgrade server address: ipv4[1], ipv6[2]." DEFVAL { ipv4 } ::= { msanSystemSwUpgrade 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.10.4 msanSystemSwUpgradeServerIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The remote SW upgrade server IP address." ::= { msanSystemSwUpgrade 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.10.5 msanSystemSwUpgradeServerDnsName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The remote SW upgrade server dns name." DEFVAL { ''b } ::= { msanSystemSwUpgrade 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.10.6 msanSystemSwUpgradeProtocol OBJECT-TYPE SYNTAX INTEGER { tftp(1), ftp(2), sftp(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The SW upgrade protocol." DEFVAL { tftp } ::= { msanSystemSwUpgrade 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.10.7 msanSystemSwUpgradeProtocolPortId OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The SW upgrade protocol port number. If value is set to -1, standard protocol number is used." DEFVAL { -1 } ::= { msanSystemSwUpgrade 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.10.8 msanSystemSwUpgradeUserName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The username used in SW upgrade protocol. When sftp upgrade protocol is used, username must be set." DEFVAL { ''b } ::= { msanSystemSwUpgrade 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.10.9 msanSystemSwUpgradeUserPassword OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The user password used in SW upgrade protocol. When sftp upgrade protocol is used, username must be set." DEFVAL { ''b } ::= { msanSystemSwUpgrade 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.10.10 msanSystemSwUpgradePath OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The path to the SW package location." DEFVAL { ''b } ::= { msanSystemSwUpgrade 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.10.11 msanSystemSwUpgradePackageName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The SW package name" DEFVAL { ''b } ::= { msanSystemSwUpgrade 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.11 msanSystemLogsUpload OBJECT IDENTIFIER ::= { msanSystem 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.11.1 msanSystemLogsUploadStart OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Control of system logs upload procedure. When set to enable(1) transfer of file to defined server is started." DEFVAL { disable } ::= { msanSystemLogsUpload 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.11.2 msanSystemLogsUploadStatus OBJECT-TYPE SYNTAX INTEGER { inprogress(1), successful(2), failed(3), notInitiated(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The system logs upload status info." DEFVAL { notInitiated } ::= { msanSystemLogsUpload 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.11.3 msanSystemLogsUploadServerIpAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the type of the system logs upload server address: ipv4[1], ipv6[2]." DEFVAL { ipv4 } ::= { msanSystemLogsUpload 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.11.4 msanSystemLogsUploadServerIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The remote system logs upload server IP address." ::= { msanSystemLogsUpload 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.11.5 msanSystemLogsUploadServerDnsName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The remote system logs upload server dns name." DEFVAL { ''b } ::= { msanSystemLogsUpload 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.11.6 msanSystemLogsUploadProtocol OBJECT-TYPE SYNTAX INTEGER { tftp(1), ftp(2), sftp(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The system logs upload protocol." DEFVAL { tftp } ::= { msanSystemLogsUpload 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.11.7 msanSystemLogsUploadProtocolPortId OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The system logs upload protocol port number. If value is set to -1, standard protocol number is used." DEFVAL { -1 } ::= { msanSystemLogsUpload 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.11.8 msanSystemLogsUploadUserName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The username used in system logs upload protocol. When sftp upgrade protocol is used, username must be set." DEFVAL { ''b } ::= { msanSystemLogsUpload 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.11.9 msanSystemLogsUploadUserPassword OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The user password used in system logs upload protocol. When sftp upgrade protocol is used, username must be set." DEFVAL { ''b } ::= { msanSystemLogsUpload 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.11.10 msanSystemLogsUploadPath OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The path to the system logs file location." DEFVAL { ''b } ::= { msanSystemLogsUpload 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.1.11.11 msanSystemLogsUploadFileName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The system logs file name" DEFVAL { ''b } ::= { msanSystemLogsUpload 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.3 msanProfiles OBJECT IDENTIFIER ::= { msanAdditionalConf 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.1 msanVDSLProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanVDSLProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanProfiles 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.1.1 msanVDSLProfileEntry OBJECT-TYPE SYNTAX MsanVDSLProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { vdslLineConfProfileName } ::= { msanVDSLProfileTable 1 } MsanVDSLProfileEntry ::= SEQUENCE { msanVDSLProfileType INTEGER, msanVDSL2LineProfile INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.3.1.1.1 msanVDSLProfileType OBJECT-TYPE SYNTAX INTEGER { other(1), default(2), local(3), global(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Profile type: - other ~ none of the following - defaut ~ default profile - local ~ local configured profile type - global ~ global configured profile type" ::= { msanVDSLProfileEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.1.1.2 msanVDSL2LineProfile OBJECT-TYPE SYNTAX INTEGER { vdsl2profile8c(1), vdsl2profile8d(2), vdsl2profile12a(3), vdsl2profile12b(4), vdsl2profile17a(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "VDSL2 profile" ::= { msanVDSLProfileEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2 msanServiceProfile OBJECT IDENTIFIER ::= { msanProfiles 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1 msanServiceProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanServiceProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Service Profile table " ::= { msanServiceProfile 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1 msanServiceProfileEntry OBJECT-TYPE SYNTAX MsanServiceProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Service Profile table entry." INDEX { msanServiceProfileName } ::= { msanServiceProfileTable 1 } MsanServiceProfileEntry ::= SEQUENCE { msanServiceProfileName OCTET STRING, msanServiceProfileProtection INTEGER, msanServiceProfileStatus INTEGER, msanServiceProfileServiceFlowProfileName OCTET STRING, msanServiceProfileMulticastProfileName OCTET STRING, msanServiceProfileVlanProfileName OCTET STRING, msanServiceProfileL2cpProfileName OCTET STRING, msanServiceProfileSecurityProfileName OCTET STRING, msanServiceProfileAtmVpi Integer32, msanServiceProfileAtmVci Integer32, msanServiceProfileDhcpRa INTEGER, msanServiceProfileDhcpRaTrustClients INTEGER, msanServiceProfileDhcpRaOpt82UnicastExtension INTEGER, msanServiceProfileDhcpRaOpt82Insert INTEGER, msanServiceProfileDhcpRaRemoteId OCTET STRING, msanServiceProfileDhcpRaRateLimit Unsigned32, msanServiceProfilePppoeIA INTEGER, msanServiceProfilePppoeIARateLimit Unsigned32, msanServiceProfileDescription OCTET STRING, msanServiceProfileRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.1 msanServiceProfileName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..64)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Name for service profile." ::= { msanServiceProfileEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.2 msanServiceProfileProtection OBJECT-TYPE SYNTAX INTEGER { unprotected(0), protected(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanServiceProfileStatus = dynamic(2)" DEFVAL { unprotected } ::= { msanServiceProfileEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.3 msanServiceProfileStatus OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Profile status. If status is dynamic, profile values can't be edited." ::= { msanServiceProfileEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.4 msanServiceProfileServiceFlowProfileName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Index of used service flow profile (this profile must be set before), which indicates row in msanServiceFlowProfileTable. Empty string indicates that parameter has not been defined." ::= { msanServiceProfileEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.5 msanServiceProfileMulticastProfileName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Index of used multicast profile (this profile must be set before), which indicates row in msanMulticastProfileTable. Empty string indicates that parameter has not been defined." ::= { msanServiceProfileEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.6 msanServiceProfileVlanProfileName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Index of used vlan profile (this profile must be set before), which indicates row in msanVlanProfileTable. Empty string indicates that parameter has not been defined." ::= { msanServiceProfileEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.7 msanServiceProfileL2cpProfileName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Index of used L2CP profile (this profile must be set before), which indicates row in msanL2cpProfileTable. Empty string indicates that parameter has not been defined." ::= { msanServiceProfileEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.8 msanServiceProfileSecurityProfileName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Index of used security profile (this profile must be set before), which indicates row in msanSecurityProfileTable. Empty string indicates that parameter has not been defined." ::= { msanServiceProfileEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.9 msanServiceProfileAtmVpi OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Virtual Path Identifier. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceProfileEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.10 msanServiceProfileAtmVci OBJECT-TYPE SYNTAX Integer32 (-1 | 32..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Virtual Channel Identifier. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceProfileEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.11 msanServiceProfileDhcpRa OBJECT-TYPE SYNTAX INTEGER { disabled(0), allowClients(1), allowServers(2), allowAll(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Dynamic Host Configuration Protocol Relay Agent. DHCP RA and PPPoE IA can not be included simultaneously." DEFVAL { disabled } ::= { msanServiceProfileEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.12 msanServiceProfileDhcpRaTrustClients OBJECT-TYPE SYNTAX INTEGER { notTrust(0), trust(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "DHCP RA Trust Clients. Effective only if DHCP-RA is in either allow-all or allow-client mode." DEFVAL { notTrust } ::= { msanServiceProfileEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.13 msanServiceProfileDhcpRaOpt82UnicastExtension OBJECT-TYPE SYNTAX INTEGER { notUsed(0), used(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "DHCP RA option82 unicast extension. Effective only if DHCP-RA is in either allow-all or allow-client mode." DEFVAL { notUsed } ::= { msanServiceProfileEntry 13 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.14 msanServiceProfileDhcpRaOpt82Insert OBJECT-TYPE SYNTAX INTEGER { notInsert(0), insert(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "DHCP Relay Agent Insert Option 82. Effective only if DHCP-RA is in either allow-all or allow-client mode." DEFVAL { notInsert } ::= { msanServiceProfileEntry 14 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.15 msanServiceProfileDhcpRaRemoteId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..63)) MAX-ACCESS read-write STATUS current DESCRIPTION "DHCP Relay Agent Remote Identification. Effective only if DHCP-RA is in either allow-all or allow-client mode." DEFVAL { "" } ::= { msanServiceProfileEntry 15 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.16 msanServiceProfileDhcpRaRateLimit OBJECT-TYPE SYNTAX Unsigned32 (0..1000) MAX-ACCESS read-write STATUS current DESCRIPTION "Max rate for DHCP Relay Agent. " DEFVAL { 5 } ::= { msanServiceProfileEntry 16 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.17 msanServiceProfilePppoeIA OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Point-to-Point Protocol over Ethernet Intermediate Agent. DHCP RA and PPPoE IA can not be included simultaneously." DEFVAL { disable } ::= { msanServiceProfileEntry 17 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.18 msanServiceProfilePppoeIARateLimit OBJECT-TYPE SYNTAX Unsigned32 (0..1000) MAX-ACCESS read-write STATUS current DESCRIPTION "Max rate for PPPoE IA. " DEFVAL { 5 } ::= { msanServiceProfileEntry 18 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.19 msanServiceProfileDescription OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "Attribute specifies text which describes the associated object." DEFVAL { "" } ::= { msanServiceProfileEntry 19 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.20 msanServiceProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). Value active(1) will activate and value destroy(6) will remove this entry. Other values are currently not supported. Row can be activated only if msanServiceProfileServiceFlowProfileName is specified." ::= { msanServiceProfileEntry 20 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.2 msanServicePortProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanServicePortProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A connection between service profiles and device ports" ::= { msanServiceProfile 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.2.1 msanServicePortProfileEntry OBJECT-TYPE SYNTAX MsanServicePortProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Service Profile Port table entry." INDEX { ifIndex, msanServiceProfileName } ::= { msanServicePortProfileTable 1 } MsanServicePortProfileEntry ::= SEQUENCE { msanServicePortProfileRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.3.2.2.1.1 msanServicePortProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanServicePortProfileEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3 msanServiceFlowProfile OBJECT IDENTIFIER ::= { msanProfiles 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1 msanServiceFlowProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanServiceFlowProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Service Flow Profile table " ::= { msanServiceFlowProfile 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1 msanServiceFlowProfileEntry OBJECT-TYPE SYNTAX MsanServiceFlowProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Service Flow Profile table entry." INDEX { msanServiceFlowProfileName } ::= { msanServiceFlowProfileTable 1 } MsanServiceFlowProfileEntry ::= SEQUENCE { msanServiceFlowProfileName OCTET STRING, msanServiceFlowProfileProtection INTEGER, msanServiceFlowProfileStatus INTEGER, msanServiceFlowProfileMatchUsAny INTEGER, msanServiceFlowProfileMatchUsMacDestAddr MacAddress, msanServiceFlowProfileMatchUsMacDestMask MacAddress, msanServiceFlowProfileMatchUsMacSrcAddr MacAddress, msanServiceFlowProfileMatchUsMacSrcMask MacAddress, msanServiceFlowProfileMatchUsCPcp Integer32, msanServiceFlowProfileMatchUsSPcp Integer32, msanServiceFlowProfileMatchUsVlanProfile INTEGER, msanServiceFlowProfileMatchUsCVlanIdRange OCTET STRING, msanServiceFlowProfileMatchUsSVlanIdRange OCTET STRING, msanServiceFlowProfileMatchUsEthertype Integer32, msanServiceFlowProfileMatchUsIpProtocol Integer32, msanServiceFlowProfileMatchUsIpSrcAddr IpAddress, msanServiceFlowProfileMatchUsIpSrcMask IpAddress, msanServiceFlowProfileMatchUsIpDestAddr IpAddress, msanServiceFlowProfileMatchUsIpDestMask IpAddress, msanServiceFlowProfileMatchUsIpDscp Integer32, msanServiceFlowProfileMatchUsIpCsc Integer32, msanServiceFlowProfileMatchUsIpDropPrecedence INTEGER, msanServiceFlowProfileMatchUsTcpSrcPort Integer32, msanServiceFlowProfileMatchUsTcpDestPort Integer32, msanServiceFlowProfileMatchUsUdpSrcPort Integer32, msanServiceFlowProfileMatchUsUdpDstPort Integer32, msanServiceFlowProfileMatchDsAny INTEGER, msanServiceFlowProfileMatchDsMacDestAddr MacAddress, msanServiceFlowProfileMatchDsMacDestMask MacAddress, msanServiceFlowProfileMatchDsMacSrcAddr MacAddress, msanServiceFlowProfileMatchDsMacSrcMask MacAddress, msanServiceFlowProfileMatchDsCPcp Integer32, msanServiceFlowProfileMatchDsSPcp Integer32, msanServiceFlowProfileMatchDsVlanProfile INTEGER, msanServiceFlowProfileMatchDsCVlanIdRange OCTET STRING, msanServiceFlowProfileMatchDsSVlanIdRange OCTET STRING, msanServiceFlowProfileMatchDsEthertype Integer32, msanServiceFlowProfileMatchDsIpProtocol Integer32, msanServiceFlowProfileMatchDsIpSrcAddr IpAddress, msanServiceFlowProfileMatchDsIpSrcMask IpAddress, msanServiceFlowProfileMatchDsIpDestAddr IpAddress, msanServiceFlowProfileMatchDsIpDestMask IpAddress, msanServiceFlowProfileMatchDsIpDscp Integer32, msanServiceFlowProfileMatchDsIpCsc Integer32, msanServiceFlowProfileMatchDsIpDropPrecedence INTEGER, msanServiceFlowProfileMatchDsTcpSrcPort Integer32, msanServiceFlowProfileMatchDsTcpDestPort Integer32, msanServiceFlowProfileMatchDsUdpSrcPort Integer32, msanServiceFlowProfileMatchDsUdpDstPort Integer32, msanServiceFlowProfileUsCdr Integer32, msanServiceFlowProfileUsCdrBurstSize Integer32, msanServiceFlowProfileUsPdr Integer32, msanServiceFlowProfileUsPdrBurstSize Integer32, msanServiceFlowProfileUsMarkPcp INTEGER, msanServiceFlowProfileUsMarkPcpValue INTEGER, msanServiceFlowProfileUsMarkDscp INTEGER, msanServiceFlowProfileUsMarkDscpValue INTEGER, msanServiceFlowProfileDsCdr Integer32, msanServiceFlowProfileDsCdrBurstSize Integer32, msanServiceFlowProfileDsPdr Integer32, msanServiceFlowProfileDsPdrBurstSize Integer32, msanServiceFlowProfileDsMarkPcp INTEGER, msanServiceFlowProfileDsMarkPcpValue INTEGER, msanServiceFlowProfileDsMarkDscp INTEGER, msanServiceFlowProfileDsMarkDscpValue INTEGER, msanServiceFlowProfileDsQueuingPriority INTEGER, msanServiceFlowProfileDsSchedulingMode INTEGER, msanServiceFlowProfileDescription OCTET STRING, msanServiceFlowProfileRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.1 msanServiceFlowProfileName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Service Flow Profile Name." ::= { msanServiceFlowProfileEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.2 msanServiceFlowProfileProtection OBJECT-TYPE SYNTAX INTEGER { unprotected(0), protected(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanServiceFlowProfileStatus = dynamic(2)" DEFVAL { unprotected } ::= { msanServiceFlowProfileEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.3 msanServiceFlowProfileStatus OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Profile status. If status is dynamic, profile values can't be edited." ::= { msanServiceFlowProfileEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.4 msanServiceFlowProfileMatchUsAny OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Match every upstream packet frame." DEFVAL { disable } ::= { msanServiceFlowProfileEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.5 msanServiceFlowProfileMatchUsMacDestAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match upstream packet frame with specified destination MAC address. Empty string indicates that parameter has not been defined" DEFVAL { ''b } ::= { msanServiceFlowProfileEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.6 msanServiceFlowProfileMatchUsMacDestMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanServiceFlowProfileMatchUsMacDestAddr that is compared with upstream packet. Empty string indicates that parameter has not been defined" DEFVAL { ''b } ::= { msanServiceFlowProfileEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.7 msanServiceFlowProfileMatchUsMacSrcAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match upstream packet frame with specified source MAC address. Empty string indicates that parameter has not been defined" DEFVAL { ''b } ::= { msanServiceFlowProfileEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.8 msanServiceFlowProfileMatchUsMacSrcMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanServiceFlowProfileMatchUsMacSrcAddr that is compared with upstream packet. Empty string indicates that parameter has not been defined" DEFVAL { ''b } ::= { msanServiceFlowProfileEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.9 msanServiceFlowProfileMatchUsCPcp OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Match upstream packet frame with specified Customer PCP (Priority Code Point) - PCP is also known as class of service (CoS) bits. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.10 msanServiceFlowProfileMatchUsSPcp OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Match upstream packet frame with specified Service PCP (Priority Code Point). PCP is also known as class of service (CoS) bits. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.11 msanServiceFlowProfileMatchUsVlanProfile OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Match upstream packet frame with VLAN Id values from VLAN Service Profile (msanVlanProfileTable). " DEFVAL { disable } ::= { msanServiceFlowProfileEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.12 msanServiceFlowProfileMatchUsCVlanIdRange OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..512)) MAX-ACCESS read-write STATUS current DESCRIPTION "Match upstream packet frame with specified list (bitmask) of Customer VLAN Id. An empty string indicates that parameter has not been defined." DEFVAL { ''b } ::= { msanServiceFlowProfileEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.13 msanServiceFlowProfileMatchUsSVlanIdRange OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..512)) MAX-ACCESS read-write STATUS current DESCRIPTION "Match upstream packet frame with specified list (bitmask) of Service VLAN Id. An empty string indicates that parameter has not been defined." DEFVAL { ''b } ::= { msanServiceFlowProfileEntry 13 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.14 msanServiceFlowProfileMatchUsEthertype OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Match upstream packet frame with specified EtherType value. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 14 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.15 msanServiceFlowProfileMatchUsIpProtocol OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Match upstream packet frame with specified IP protocol value. A value of -1 indicates that parameter has not been defined. Some of standard protocol values: icmp - 1 igmp - 2 ip - 4 (ip in ip encapsulation) tcp - 6 udp - 17" DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 15 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.16 msanServiceFlowProfileMatchUsIpSrcAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match upstream packet frame with specified source IP address. Empty string indicates that parameter has not been defined." DEFVAL { ''h } ::= { msanServiceFlowProfileEntry 16 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.17 msanServiceFlowProfileMatchUsIpSrcMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanServiceFlowProfileMatchUsIpSrcAddr that is compared with upstream packet. Empty string indicates that parameter has not been defined" DEFVAL { ''h } ::= { msanServiceFlowProfileEntry 17 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.18 msanServiceFlowProfileMatchUsIpDestAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match upstream packet frame with specified destination IP address. Empty string indicates that parameter has not been defined." DEFVAL { ''h } ::= { msanServiceFlowProfileEntry 18 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.19 msanServiceFlowProfileMatchUsIpDestMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanServiceFlowProfileMatchUsIpDestAddr that is compared with upstream packet. Empty string indicates that parameter has not been defined" DEFVAL { ''h } ::= { msanServiceFlowProfileEntry 19 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.20 msanServiceFlowProfileMatchUsIpDscp OBJECT-TYPE SYNTAX Integer32 (-1..63) MAX-ACCESS read-write STATUS current DESCRIPTION "Match upstream packet frame with specified CSC (Class Selector Code Point) = IP precedence (part of TOS field) value. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 20 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.21 msanServiceFlowProfileMatchUsIpCsc OBJECT-TYPE SYNTAX Integer32 (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Match upstream packet frame with specified IP precedence (part of TOS field) value. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 21 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.22 msanServiceFlowProfileMatchUsIpDropPrecedence OBJECT-TYPE SYNTAX INTEGER { notDefined(-1), noDrop(0), lowDrop(1), mediumDrop(2), highDrop(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Match upstream packet frame with specified Drop precedence two bits value: noDrop(0) -> 00 lowDrop(1) -> 01 mediumDrop(2) -> 10 highDrop(3) -> 11 A value of -1 indicates that parameter has not been defined." DEFVAL { notDefined } ::= { msanServiceFlowProfileEntry 22 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.23 msanServiceFlowProfileMatchUsTcpSrcPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Match upstream packet frame with specified source TCP port number. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 23 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.24 msanServiceFlowProfileMatchUsTcpDestPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Match upstream packet frame with specified destination TCP port number. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 24 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.25 msanServiceFlowProfileMatchUsUdpSrcPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Match upstream packet frame with specified source UDP port number. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 25 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.26 msanServiceFlowProfileMatchUsUdpDstPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Match upstream packet frame with specified destination UDP port number. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 26 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.27 msanServiceFlowProfileMatchDsAny OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Match every downstream packet frame." DEFVAL { disable } ::= { msanServiceFlowProfileEntry 27 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.28 msanServiceFlowProfileMatchDsMacDestAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match downstream packet frame with specified destination MAC address. Empty string indicates that parameter has not been defined" DEFVAL { ''b } ::= { msanServiceFlowProfileEntry 28 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.29 msanServiceFlowProfileMatchDsMacDestMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanServiceFlowProfileMatchDsMacDestAddr that is compared with downstream packet. Empty string indicates that parameter has not been defined" DEFVAL { ''b } ::= { msanServiceFlowProfileEntry 29 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.30 msanServiceFlowProfileMatchDsMacSrcAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match downstream packet frame with specified source MAC address. Empty string indicates that parameter has not been defined" DEFVAL { ''b } ::= { msanServiceFlowProfileEntry 30 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.31 msanServiceFlowProfileMatchDsMacSrcMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanServiceFlowProfileMatchDsMacSrcAddr that is compared with downstream packet. Empty string indicates that parameter has not been defined" DEFVAL { ''b } ::= { msanServiceFlowProfileEntry 31 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.32 msanServiceFlowProfileMatchDsCPcp OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Match downstream packet frame with specified Customer PCP (Priority Code Point) - PCP is also known as class of service (CoS) bits. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 32 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.33 msanServiceFlowProfileMatchDsSPcp OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Match downstream packet frame with specified Service PCP (Priority Code Point). PCP is also known as class of service (CoS) bits. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 33 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.34 msanServiceFlowProfileMatchDsVlanProfile OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Match downstream packet frame with VLAN Id values from VLAN Service Profile (msanVlanProfileTable). " DEFVAL { disable } ::= { msanServiceFlowProfileEntry 34 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.35 msanServiceFlowProfileMatchDsCVlanIdRange OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..512)) MAX-ACCESS read-write STATUS current DESCRIPTION "Match downstream packet frame with specified list (bitmask) of Customer VLAN Id. An emptya string indicates that parameter has not been defined." DEFVAL { ''b } ::= { msanServiceFlowProfileEntry 35 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.36 msanServiceFlowProfileMatchDsSVlanIdRange OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..512)) MAX-ACCESS read-write STATUS current DESCRIPTION "Match downstream packet frame with specified list (bitmask) of Service VLAN Id. An empty string indicates that parameter has not been defined." DEFVAL { ''b } ::= { msanServiceFlowProfileEntry 36 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.37 msanServiceFlowProfileMatchDsEthertype OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Match downstream packet frame with specified EtherType value. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 37 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.38 msanServiceFlowProfileMatchDsIpProtocol OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Match downstream packet frame with specified IP protocol value. A value of -1 indicates that parameter has not been defined. Some of standard protocol values: icmp - 1 igmp - 2 ip - 4 (ip in ip encapsulation) tcp - 6 udp - 17" DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 38 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.39 msanServiceFlowProfileMatchDsIpSrcAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match downstream packet frame with specified source IP address. Empty string indicates that parameter has not been defined." DEFVAL { ''h } ::= { msanServiceFlowProfileEntry 39 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.40 msanServiceFlowProfileMatchDsIpSrcMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanServiceFlowProfileMatchDsIpSrcAddr that is compared with downstream packet. Empty string indicates that parameter has not been defined" DEFVAL { ''h } ::= { msanServiceFlowProfileEntry 40 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.41 msanServiceFlowProfileMatchDsIpDestAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match downstream packet frame with specified destination IP address. Empty string indicates that parameter has not been defined." DEFVAL { ''h } ::= { msanServiceFlowProfileEntry 41 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.42 msanServiceFlowProfileMatchDsIpDestMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanServiceFlowProfileMatchDsIpDestAddr that is compared with downstream packet. Empty string indicates that parameter has not been defined" DEFVAL { ''h } ::= { msanServiceFlowProfileEntry 42 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.43 msanServiceFlowProfileMatchDsIpDscp OBJECT-TYPE SYNTAX Integer32 (-1..63) MAX-ACCESS read-write STATUS current DESCRIPTION "Match downstream packet frame with specified IP DSCP value. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 43 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.44 msanServiceFlowProfileMatchDsIpCsc OBJECT-TYPE SYNTAX Integer32 (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Match downstream packet frame with specified CSC (Class Selector Code Point) = IP precedence (part of TOS field) value. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 44 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.45 msanServiceFlowProfileMatchDsIpDropPrecedence OBJECT-TYPE SYNTAX INTEGER { notDefined(-1), noDrop(0), lowDrop(1), mediumDrop(2), highDrop(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Match downstream packet frame with specified Drop precedence two bits value: noDrop(0) -> 00 lowDrop(1) -> 01 mediumDrop(2) -> 10 highDrop(3) -> 11 A value of -1 indicates that parameter has not been defined." DEFVAL { notDefined } ::= { msanServiceFlowProfileEntry 45 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.46 msanServiceFlowProfileMatchDsTcpSrcPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Match downstream packet frame with specified source TCP port number. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 46 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.47 msanServiceFlowProfileMatchDsTcpDestPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Match downstream packet frame with specified destination TCP port number. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 47 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.48 msanServiceFlowProfileMatchDsUdpSrcPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Match downstream packet frame with specified source UDP port number. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 48 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.49 msanServiceFlowProfileMatchDsUdpDstPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Match downstream packet frame with specified destination UDP port number. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 49 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.50 msanServiceFlowProfileUsCdr OBJECT-TYPE SYNTAX Integer32 (0..1000000) UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Upstream committed data rate (E-CDR) in kbps (0 – 1000000)." DEFVAL { 0 } ::= { msanServiceFlowProfileEntry 50 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.51 msanServiceFlowProfileUsCdrBurstSize OBJECT-TYPE SYNTAX Integer32 (0..16384) UNITS "kB" MAX-ACCESS read-write STATUS current DESCRIPTION "Upstream committed data rate burst size in kB (0 – 16384). When parameter is set to 0 (default), it's automatically updated to default burst size in according with current msanQoSProfileInCdr value." DEFVAL { 0 } ::= { msanServiceFlowProfileEntry 51 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.52 msanServiceFlowProfileUsPdr OBJECT-TYPE SYNTAX Integer32 (0..1000000) UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Upstream peak data rate (E-PDR) in kbps (0 – 1000000)." DEFVAL { 0 } ::= { msanServiceFlowProfileEntry 52 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.53 msanServiceFlowProfileUsPdrBurstSize OBJECT-TYPE SYNTAX Integer32 (0..16384) UNITS "kB" MAX-ACCESS read-write STATUS current DESCRIPTION "Upstream peak data rate burst size in kB (0 – 16384). When parameter is set to 0 (default), it's automatically updated to default burst size in according with current msanQoSProfileInPdr value." DEFVAL { 0 } ::= { msanServiceFlowProfileEntry 53 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.54 msanServiceFlowProfileUsMarkPcp OBJECT-TYPE SYNTAX INTEGER { none(1), copyFromCsc(2), userValue(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type of upstrem PCP marking. If set to userValue(3), parameter msanServiceFlowProfileUsMarkPcpValue is used. A value of none(1) indicates that parameter has not been defined" DEFVAL { none } ::= { msanServiceFlowProfileEntry 54 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.55 msanServiceFlowProfileUsMarkPcpValue OBJECT-TYPE SYNTAX INTEGER (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Mark upstream packets with specified PCP (Priority Code Point) value (0-7) = CoS. A value of -1 indicates that parameter has not been defined" DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 55 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.56 msanServiceFlowProfileUsMarkDscp OBJECT-TYPE SYNTAX INTEGER { none(1), copyFromPcp(2), userValue(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type of upstrem DSCP marking. If set to userValue(3), parameter msanServiceFlowProfileUsMarkDscpValue is used. A value of none(1) indicates that parameter has not been defined" DEFVAL { none } ::= { msanServiceFlowProfileEntry 56 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.57 msanServiceFlowProfileUsMarkDscpValue OBJECT-TYPE SYNTAX INTEGER (-1..63) MAX-ACCESS read-write STATUS current DESCRIPTION "Mark upstream packets with specified DSCP (Diffserv Code Point) value (0-63). A value of -1 indicates that parameter has not been defined" DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 57 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.58 msanServiceFlowProfileDsCdr OBJECT-TYPE SYNTAX Integer32 (0..1000000) UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Downstream committed data rate (E-CDR) in kbps (0 – 1000000)." DEFVAL { 0 } ::= { msanServiceFlowProfileEntry 58 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.59 msanServiceFlowProfileDsCdrBurstSize OBJECT-TYPE SYNTAX Integer32 (0..16384) UNITS "kB" MAX-ACCESS read-write STATUS current DESCRIPTION "Downstream committed data rate burst size in kB (0 – 16384). When parameter is set to 0 (default), it's automatically updated to default burst size in according with current msanQoSProfileOutCdr value." DEFVAL { 0 } ::= { msanServiceFlowProfileEntry 59 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.60 msanServiceFlowProfileDsPdr OBJECT-TYPE SYNTAX Integer32 (0..1000000) UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Downstream peak data rate (E-PDR) in kbps (0 – 1000000)." DEFVAL { 0 } ::= { msanServiceFlowProfileEntry 60 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.61 msanServiceFlowProfileDsPdrBurstSize OBJECT-TYPE SYNTAX Integer32 (0..16384) UNITS "kB" MAX-ACCESS read-write STATUS current DESCRIPTION "Downstream peak data rate burst size in kB (0 – 16384). When parameter is set to 0 (default), it's automatically updated to default burst size in according with current msanQoSProfileOutCdr value. " DEFVAL { 0 } ::= { msanServiceFlowProfileEntry 61 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.62 msanServiceFlowProfileDsMarkPcp OBJECT-TYPE SYNTAX INTEGER { none(1), copyFromCsc(2), userValue(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type of downstream PCP marking. If set to userValue(3), parameter msanServiceFlowProfileDsMarkPcpValue is used. A value of none(1) indicates that parameter has not been defined" DEFVAL { none } ::= { msanServiceFlowProfileEntry 62 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.63 msanServiceFlowProfileDsMarkPcpValue OBJECT-TYPE SYNTAX INTEGER (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Mark downstream packets with specified PCP (Priority Code Point) value (0-7) = CoS. A value of -1 indicates that parameter has not been defined" DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 63 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.64 msanServiceFlowProfileDsMarkDscp OBJECT-TYPE SYNTAX INTEGER { none(1), copyFromPcp(2), userValue(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type of downstrem DSCP marking. If set to userValue(3), parameter msanServiceFlowProfileDsMarkDscpValue is used. A value of none(1) indicates that parameter has not been defined" DEFVAL { none } ::= { msanServiceFlowProfileEntry 64 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.65 msanServiceFlowProfileDsMarkDscpValue OBJECT-TYPE SYNTAX INTEGER (-1..63) MAX-ACCESS read-write STATUS current DESCRIPTION "Mark downstream packets with specified DSCP (Diffserv Code Point) value (0-63). A value of -1 indicates that parameter has not been defined" DEFVAL { -1 } ::= { msanServiceFlowProfileEntry 65 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.66 msanServiceFlowProfileDsQueuingPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Queuing Priority of Service Flow Profile. " DEFVAL { 0 } ::= { msanServiceFlowProfileEntry 66 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.67 msanServiceFlowProfileDsSchedulingMode OBJECT-TYPE SYNTAX INTEGER { weighted(1), strict(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Scheduling Mode" DEFVAL { weighted } ::= { msanServiceFlowProfileEntry 67 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.68 msanServiceFlowProfileDescription OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "Attribute specifies text which describes the associated object." DEFVAL { "" } ::= { msanServiceFlowProfileEntry 68 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.69 msanServiceFlowProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanServiceFlowProfileEntry 69 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.4 msanVlanProfile OBJECT IDENTIFIER ::= { msanProfiles 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.4.1 msanVlanProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanVlanProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Vlan Profile table " ::= { msanVlanProfile 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1 msanVlanProfileEntry OBJECT-TYPE SYNTAX MsanVlanProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Vlan Profile table entry." INDEX { msanVlanProfileName } ::= { msanVlanProfileTable 1 } MsanVlanProfileEntry ::= SEQUENCE { msanVlanProfileName OCTET STRING, msanVlanProfileProtection INTEGER, msanVlanProfileStatus INTEGER, msanVlanProfileCVid OCTET STRING, msanVlanProfileCVidNative Integer32, msanVlanProfileCVidRemark Integer32, msanVlanProfileSVid Integer32, msanVlanProfileSEtherType Integer32, msanVlanProfileDescription OCTET STRING, msanVlanProfileRowStatus RowStatus, msanVlanProfileNetworkPortCTag INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.1 msanVlanProfileName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Name for the VLAN profile." ::= { msanVlanProfileEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.2 msanVlanProfileProtection OBJECT-TYPE SYNTAX INTEGER { unprotected(0), protected(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanVlanProfileStatus = dynamic(2)" DEFVAL { unprotected } ::= { msanVlanProfileEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.3 msanVlanProfileStatus OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Profile status. If status is dynamic, profile values can't be edited." ::= { msanVlanProfileEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.4 msanVlanProfileCVid OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..512)) MAX-ACCESS read-write STATUS current DESCRIPTION "Customer VLANs Identification (bit mask)." DEFVAL { "" } ::= { msanVlanProfileEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.5 msanVlanProfileCVidNative OBJECT-TYPE SYNTAX Integer32 (-1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Nativ C-VLAN Id. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanVlanProfileEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.6 msanVlanProfileCVidRemark OBJECT-TYPE SYNTAX Integer32 (-1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Remark C-VLAN Id. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanVlanProfileEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.7 msanVlanProfileSVid OBJECT-TYPE SYNTAX Integer32 (-1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "S-VLAN Id. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanVlanProfileEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.8 msanVlanProfileSEtherType OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Ether Type value. " DEFVAL { '88a8'h } ::= { msanVlanProfileEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.10 msanVlanProfileDescription OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "Attribute specifies text which describes the associated object." DEFVAL { "" } ::= { msanVlanProfileEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.11 msanVlanProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanVlanProfileEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.12 msanVlanProfileNetworkPortCTag OBJECT-TYPE SYNTAX INTEGER { use(1), notUse(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Usage of C-VLAN tag on network port. If assigned as notUse(2) in upstream direction, C-VLAN tag is removed." DEFVAL { use } ::= { msanVlanProfileEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.4.2 msanVlanPortProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanVlanPortProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A connection between VLAN profiles and device ports" ::= { msanVlanProfile 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.4.2.1 msanVlanPortProfileEntry OBJECT-TYPE SYNTAX MsanVlanPortProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Service Profile Port table entry." INDEX { ifIndex, msanVlanProfileName } ::= { msanVlanPortProfileTable 1 } MsanVlanPortProfileEntry ::= SEQUENCE { msanVlanPortProfileRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.3.4.2.1.1 msanVlanPortProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanVlanPortProfileEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5 msanMulticastProfile OBJECT IDENTIFIER ::= { msanProfiles 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.1 msanMulticastProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMulticastProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Multicast Profile table " ::= { msanMulticastProfile 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1 msanMulticastProfileEntry OBJECT-TYPE SYNTAX MsanMulticastProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Multicast Profile table entry." INDEX { msanMulticastProfileName } ::= { msanMulticastProfileTable 1 } MsanMulticastProfileEntry ::= SEQUENCE { msanMulticastProfileName OCTET STRING, msanMulticastProfileProtection INTEGER, msanMulticastProfileStatus INTEGER, msanMulticastProfileIgmpSnooping INTEGER, msanMulticastProfileIgmpSnoopingFastLeave INTEGER, msanMulticastProfileIgmpSnoopingSuppression INTEGER, msanMulticastProfileIgmpProxy INTEGER, msanMulticastProfileIgmpProxyIpAddress IpAddress, msanMulticastProfileIgmpFiltering INTEGER, msanMulticastProfileMulticastGroupLimit Unsigned32, msanMulticastProfileMvr INTEGER, msanMulticastProfileDescription OCTET STRING, msanMulticastProfileRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.1 msanMulticastProfileName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Name for the Multicast profile." ::= { msanMulticastProfileEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.2 msanMulticastProfileProtection OBJECT-TYPE SYNTAX INTEGER { unprotected(0), protected(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanMulticastProfileStatus = dynamic(2)" DEFVAL { unprotected } ::= { msanMulticastProfileEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.3 msanMulticastProfileStatus OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Profile status. If status is dynamic, profile values can't be edited." ::= { msanMulticastProfileEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.4 msanMulticastProfileIgmpSnooping OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "IGMP snnoping" DEFVAL { disable } ::= { msanMulticastProfileEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.5 msanMulticastProfileIgmpSnoopingFastLeave OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "IGMP Snooping Fast Leave." DEFVAL { disable } ::= { msanMulticastProfileEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.6 msanMulticastProfileIgmpSnoopingSuppression OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "IGMP Snooping Suppression." DEFVAL { disable } ::= { msanMulticastProfileEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.7 msanMulticastProfileIgmpProxy OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "IGMP proxy." DEFVAL { disable } ::= { msanMulticastProfileEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.8 msanMulticastProfileIgmpProxyIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IGMP proxy IP address." ::= { msanMulticastProfileEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.9 msanMulticastProfileIgmpFiltering OBJECT-TYPE SYNTAX INTEGER { allowAll(0), allowReports(1), allowQueries(2), dropAll(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "IGMP filtering." DEFVAL { allowReports } ::= { msanMulticastProfileEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.10 msanMulticastProfileMulticastGroupLimit OBJECT-TYPE SYNTAX Unsigned32 (0..10) MAX-ACCESS read-write STATUS current DESCRIPTION "Multicast group limit. A value of 0 indicates not limit." DEFVAL { 0 } ::= { msanMulticastProfileEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.11 msanMulticastProfileMvr OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Multicast VLAN Registration." DEFVAL { disable } ::= { msanMulticastProfileEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.12 msanMulticastProfileDescription OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "Attribute specifies text which describes the associated object." DEFVAL { "" } ::= { msanMulticastProfileEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.13 msanMulticastProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanMulticastProfileEntry 13 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.2 msanMulticastProfileStaticGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMulticastProfileStaticGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Connection between multicast_profile and multicast_static_group table " ::= { msanMulticastProfile 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.2.1 msanMulticastProfileStaticGroupEntry OBJECT-TYPE SYNTAX MsanMulticastProfileStaticGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Multicast Profile Group table entry." INDEX { msanMulticastProfileName, msanMulticastProfileStaticGroupIpAddr } ::= { msanMulticastProfileStaticGroupTable 1 } MsanMulticastProfileStaticGroupEntry ::= SEQUENCE { msanMulticastProfileStaticGroupIpAddr IpAddress, msanMulticastProfileStaticGroupRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.2.1.1 msanMulticastProfileStaticGroupIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanMulticastProfileStaticGroupEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.5.2.1.9 msanMulticastProfileStaticGroupRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanMulticastProfileStaticGroupEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6 msanSecurityProfile OBJECT IDENTIFIER ::= { msanProfiles 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.1 msanSecurityProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanSecurityProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Security Profile table " ::= { msanSecurityProfile 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1 msanSecurityProfileEntry OBJECT-TYPE SYNTAX MsanSecurityProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Security Profile table entry." INDEX { msanSecurityProfileName } ::= { msanSecurityProfileTable 1 } MsanSecurityProfileEntry ::= SEQUENCE { msanSecurityProfileName OCTET STRING, msanSecurityProfileProtection INTEGER, msanSecurityProfileStatus INTEGER, msanSecurityProfileProtectedPort INTEGER, msanSecurityProfileMacSg INTEGER, msanSecurityProfileMacLimit Unsigned32, msanSecurityProfilePortSecurity INTEGER, msanSecurityProfileIpSg INTEGER, msanSecurityProfileIpSgBindingLimit Unsigned32, msanSecurityProfileIpSgFilteringMode INTEGER, msanSecurityProfileArpInspec INTEGER, msanSecurityProfileMacForward INTEGER, msanSecurityProfileDescription OCTET STRING, msanSecurityProfileRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.1 msanSecurityProfileName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Name of the security profile." ::= { msanSecurityProfileEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.2 msanSecurityProfileProtection OBJECT-TYPE SYNTAX INTEGER { unprotected(0), protected(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanSecurityProfileStatus = dynamic(2)" DEFVAL { unprotected } ::= { msanSecurityProfileEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.3 msanSecurityProfileStatus OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Profile status. If status is dynamic, profile values can't be edited." ::= { msanSecurityProfileEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.4 msanSecurityProfileProtectedPort OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Security profile protected port" DEFVAL { disable } ::= { msanSecurityProfileEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.5 msanSecurityProfileMacSg OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Mac source guard" DEFVAL { disable } ::= { msanSecurityProfileEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.6 msanSecurityProfileMacLimit OBJECT-TYPE SYNTAX Unsigned32 (0..64) MAX-ACCESS read-write STATUS current DESCRIPTION "MAC limit A value of 0 indicates that parameter has not been defined." DEFVAL { 0 } ::= { msanSecurityProfileEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.7 msanSecurityProfilePortSecurity OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Port security" DEFVAL { disable } ::= { msanSecurityProfileEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.8 msanSecurityProfileIpSg OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "IP source guard" DEFVAL { disable } ::= { msanSecurityProfileEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.9 msanSecurityProfileIpSgBindingLimit OBJECT-TYPE SYNTAX Unsigned32 (1..15) MAX-ACCESS read-write STATUS current DESCRIPTION "IP source guard binding limit. " DEFVAL { 4 } ::= { msanSecurityProfileEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.10 msanSecurityProfileIpSgFilteringMode OBJECT-TYPE SYNTAX INTEGER { ipSourceAddress(1), ipAndMacSourceAddress(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "IP source guard filtering mode" DEFVAL { ipAndMacSourceAddress } ::= { msanSecurityProfileEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.12 msanSecurityProfileArpInspec OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Dynamic ARP inspection" DEFVAL { disable } ::= { msanSecurityProfileEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.13 msanSecurityProfileMacForward OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "MAC forwarding" DEFVAL { disable } ::= { msanSecurityProfileEntry 13 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.14 msanSecurityProfileDescription OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "Attribute specifies text which describes the associated object." DEFVAL { "" } ::= { msanSecurityProfileEntry 14 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.15 msanSecurityProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanSecurityProfileEntry 15 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.3 msanSecurityAclProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanSecurityAclProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A connection between security profiles and access lists" ::= { msanSecurityProfile 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.3.1 msanSecurityAclProfileEntry OBJECT-TYPE SYNTAX MsanSecurityAclProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Service Profile Port table entry." INDEX { msanSecurityProfileName, msanSecurityAclProfileAclDirection, msanSecurityAclProfileSequence, msanSecurityAclProfileAclType, msanSecurityAclProfileAclId } ::= { msanSecurityAclProfileTable 1 } MsanSecurityAclProfileEntry ::= SEQUENCE { msanSecurityAclProfileAclDirection INTEGER, msanSecurityAclProfileSequence Unsigned32, msanSecurityAclProfileAclType INTEGER, msanSecurityAclProfileAclId Unsigned32, msanSecurityAclProfileRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.3.1.1 msanSecurityAclProfileAclDirection OBJECT-TYPE SYNTAX INTEGER { inbound(1), outbound(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The direction to which this ACL instance applies." ::= { msanSecurityAclProfileEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.3.1.2 msanSecurityAclProfileSequence OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The relative evaluation sequence of this ACL for this interface and direction. When multiple ACLs are allowed for a given interface and direction, the sequence number determines the order in which the list of ACLs are evaluated, with lower sequence numbers given higher precedence. The sequence number value is arbitrary, but must be a unique non-zero value for a given interface and direction. Setting this object to an existing sequence number value for a given interface and direction causes the ACL corresponding to that value to be replaced with this ACL." ::= { msanSecurityAclProfileEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.3.1.3 msanSecurityAclProfileAclType OBJECT-TYPE SYNTAX INTEGER { ip(1), mac(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of this ACL, which is used to interpret the aclIfId object value." ::= { msanSecurityAclProfileEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.3.1.4 msanSecurityAclProfileAclId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ACL identifier value. For the IP ACLs, the actual ACL number is its identifier as follows: IP standard ranges from 1-99, IP extended ranges from 100-199, and IP advanced ranges 200-299." ::= { msanSecurityAclProfileEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.6.3.1.5 msanSecurityAclProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanSecurityAclProfileEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7 msanL2cpProfile OBJECT IDENTIFIER ::= { msanProfiles 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.1 msanL2cpProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanL2cpProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "L2CP (Layer 2 Control Protocol) Profile table " ::= { msanL2cpProfile 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.1.1 msanL2cpProfileEntry OBJECT-TYPE SYNTAX MsanL2cpProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "L2cp Profile table entry." INDEX { msanL2cpProfileName } ::= { msanL2cpProfileTable 1 } MsanL2cpProfileEntry ::= SEQUENCE { msanL2cpProfileName OCTET STRING, msanL2cpProfileProtection INTEGER, msanL2cpProfileStatus INTEGER, msanL2cpProfileDescription OCTET STRING, msanL2cpProfileRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.1.1.1 msanL2cpProfileName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Name of the L2CP profile." ::= { msanL2cpProfileEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.1.1.2 msanL2cpProfileProtection OBJECT-TYPE SYNTAX INTEGER { unprotected(0), protected(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanL2cpProfileStatus = dynamic(2)" DEFVAL { unprotected } ::= { msanL2cpProfileEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.1.1.3 msanL2cpProfileStatus OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Profile status. If status is dynamic, profile values can't be edited." ::= { msanL2cpProfileEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.1.1.4 msanL2cpProfileDescription OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "Attribute specifies text which describes the associated object." DEFVAL { "" } ::= { msanL2cpProfileEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.1.1.5 msanL2cpProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanL2cpProfileEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.2 msanL2cpProtocolTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanL2cpProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table with list of L2CP protocols" ::= { msanL2cpProfile 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.2.1 msanL2cpProtocolEntry OBJECT-TYPE SYNTAX MsanL2cpProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanL2cpProtocolName } ::= { msanL2cpProtocolTable 1 } MsanL2cpProtocolEntry ::= SEQUENCE { msanL2cpProtocolName OCTET STRING, msanL2cpProtocolMacDestAddr MacAddress, msanL2cpProtocolEthertype Integer32, msanL2cpProtocolSubtype Integer32, msanL2cpProtocolRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.2.1.1 msanL2cpProtocolName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "L2CP protocol name" ::= { msanL2cpProtocolEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.2.1.2 msanL2cpProtocolMacDestAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MAC destination address of L2CP protocol. Empty string indicates that protocol is related to any MAC address." DEFVAL { ''b } ::= { msanL2cpProtocolEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.2.1.3 msanL2cpProtocolEthertype OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "L2CP protocol Ethertype. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanL2cpProtocolEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.2.1.4 msanL2cpProtocolSubtype OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "L2CP protocol subtype. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanL2cpProtocolEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.2.1.5 msanL2cpProtocolRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). Value active(1) will activate and value destroy(6) will remove this entry. Other values are currently not supported." ::= { msanL2cpProtocolEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.3 msanL2cpProfileProtocolTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanL2cpProfileProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table with connection between profiles and protocols" ::= { msanL2cpProfile 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.3.1 msanL2cpProfileProtocolEntry OBJECT-TYPE SYNTAX MsanL2cpProfileProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanL2cpProfileName, msanL2cpProtocolName } ::= { msanL2cpProfileProtocolTable 1 } MsanL2cpProfileProtocolEntry ::= SEQUENCE { msanL2cpProfileProtocolRule INTEGER, msanL2cpProfileProtocolRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.3.1.1 msanL2cpProfileProtocolRule OBJECT-TYPE SYNTAX INTEGER { discard(1), peer(2), tunnel(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "L2CP protocol rule." ::= { msanL2cpProfileProtocolEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.3.1.2 msanL2cpProfileProtocolRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). Value active(1) will activate and value destroy(6) will remove this entry. Other values are currently not supported. Row can be activated only when msanL2cpProfileProtocolRule is set." ::= { msanL2cpProfileProtocolEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.4 msanL2cpProfileVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanL2cpProfileVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table is used for connecting l2cp profile with vlan_id." ::= { msanL2cpProfile 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.4.1 msanL2cpProfileVlanEntry OBJECT-TYPE SYNTAX MsanL2cpProfileVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanL2cpProfileName, dot1qVlanIndex } ::= { msanL2cpProfileVlanTable 1 } MsanL2cpProfileVlanEntry ::= SEQUENCE { msanL2cpProfileVlanRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.3.7.4.1.1 msanL2cpProfileVlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanL2cpProfileVlanEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.8 msanXdslProfile OBJECT IDENTIFIER ::= { msanProfiles 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.8.1 msanXdsl2LineConfTemplateTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanXdsl2LineConfTemplateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanXdslProfile 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.8.1.1 msanXdsl2LineConfTemplateEntry OBJECT-TYPE SYNTAX MsanXdsl2LineConfTemplateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." AUGMENTS { xdsl2LineConfTemplateEntry } ::= { msanXdsl2LineConfTemplateTable 1 } MsanXdsl2LineConfTemplateEntry ::= SEQUENCE { msanXdsl2LineConfTempProtection INTEGER, msanXdsl2LineConfTempStatus INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.3.8.1.1.1 msanXdsl2LineConfTempProtection OBJECT-TYPE SYNTAX INTEGER { unprotected(0), protected(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanAclProfileStatus = dynamic(2)" DEFVAL { unprotected } ::= { msanXdsl2LineConfTemplateEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.8.1.1.2 msanXdsl2LineConfTempStatus OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Profile status. If status is dynamic, profile values can't be edited." ::= { msanXdsl2LineConfTemplateEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.8.2 msanXdsl2LineAlarmConfTemplateTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanXdsl2LineAlarmConfTemplateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanXdslProfile 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.8.2.1 msanXdsl2LineAlarmConfTemplateEntry OBJECT-TYPE SYNTAX MsanXdsl2LineAlarmConfTemplateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." AUGMENTS { xdsl2LineAlarmConfTemplateEntry } ::= { msanXdsl2LineAlarmConfTemplateTable 1 } MsanXdsl2LineAlarmConfTemplateEntry ::= SEQUENCE { msanXdsl2LineAlarmConfTempProtection INTEGER, msanXdsl2LineAlarmConfTempStatus INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.3.8.2.1.1 msanXdsl2LineAlarmConfTempProtection OBJECT-TYPE SYNTAX INTEGER { unprotected(0), protected(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanAclProfileStatus = dynamic(2)" DEFVAL { unprotected } ::= { msanXdsl2LineAlarmConfTemplateEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.8.2.1.2 msanXdsl2LineAlarmConfTempStatus OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Profile status. If status is dynamic, profile values can't be edited." ::= { msanXdsl2LineAlarmConfTemplateEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.3.100 msanProfileConfigStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Profile configuration status." DEFVAL { disable } ::= { msanProfiles 100 } -- 1.3.6.1.4.1.1332.1.1.5.3.4 msanDhcpRelay OBJECT IDENTIFIER ::= { msanAdditionalConf 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.1 msanDhcpRaGlobal OBJECT IDENTIFIER ::= { msanDhcpRelay 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.1.1 msanDhcpRaStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "DHCP Relay Agent status." ::= { msanDhcpRaGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.1.2 msanDhcpRaMode OBJECT-TYPE SYNTAX INTEGER { full(1), simplified(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies if the DHCP Relay Agent mode is to be Simple or Full. Default value is Full." ::= { msanDhcpRaGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.1.3 msanDhcpRaCircuitType OBJECT-TYPE SYNTAX INTEGER { trusted(1), untrusted(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies DHCP RA Circuit type as trusted(1) or untrusted(2)." ::= { msanDhcpRaGlobal 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.1.4 msanDhcpRaOpt82 OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies DHCP Relay Agent general option 82 insertion status . " ::= { msanDhcpRaGlobal 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.1.5 msanDhcpRaOpt82ReplyMode OBJECT-TYPE SYNTAX INTEGER { keep(1), remove(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies DHCP Relay Agent keep/remove option 82 in replies. " ::= { msanDhcpRaGlobal 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.1.6 msanDhcpRaOpt82CircuitIdStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the disable/enable inserting Circuit ID suboption. Default value is Enable." ::= { msanDhcpRaGlobal 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.1.7 msanDhcpRaOpt82RemoteIdStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the disable/enable inserting Remote ID suboption. Default value is Enable." ::= { msanDhcpRaGlobal 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.1.8 msanDhcpRaOpt82UnicastExtStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The desired state of insertion of option 82 in unicast frames." DEFVAL { disable } ::= { msanDhcpRaGlobal 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.1.9 msanDhcpRaFullModeSrvIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of default DHCP Server for VLANs where DHCP RA is enabled in full mode (parameter msanDhcpRaVlanMode)." ::= { msanDhcpRaGlobal 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.2 msanDhcpRaPortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanDhcpRaPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table od DHCP RA parameters per port." ::= { msanDhcpRelay 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.2.1 msanDhcpRaPortConfigEntry OBJECT-TYPE SYNTAX MsanDhcpRaPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanDhcpRaPortConfigTable 1 } MsanDhcpRaPortConfigEntry ::= SEQUENCE { msanDhcpRaPortState INTEGER, msanDhcpRaPortCircuitId OCTET STRING, msanDhcpRaPortRemoteId OCTET STRING, msanDhcpRaPortMeter INTEGER, msanDhcpRaPortMaxDataRate Integer32, msanDhcpRaPortCircuitType INTEGER, msanDhcpRaPortOpt82 INTEGER, msanDhcpRaPortOpt82ReplyMode INTEGER, msanDhcpRaPortOpt82UnicastExtStatus INTEGER, msanDhcpRaPortCircuitIdType INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.4.2.1.1 msanDhcpRaPortState OBJECT-TYPE SYNTAX INTEGER { enable(1), enableCli(2), enableSrv(3), disable(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "State of DHCP Relay Agent on the port (enable, disable, enable-client, enable-server) " ::= { msanDhcpRaPortConfigEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.2.1.2 msanDhcpRaPortCircuitId OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Option 82 Circuit Id for the port." ::= { msanDhcpRaPortConfigEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.2.1.3 msanDhcpRaPortRemoteId OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Option 82 Remote Id for the port." ::= { msanDhcpRaPortConfigEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.2.1.4 msanDhcpRaPortMeter OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable DHCP metering on port." ::= { msanDhcpRaPortConfigEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.2.1.5 msanDhcpRaPortMaxDataRate OBJECT-TYPE SYNTAX Integer32 UNITS "kb/s" MAX-ACCESS read-write STATUS current DESCRIPTION "Allowed throughput of incoming DHCP traffic on a port (kb/s)" ::= { msanDhcpRaPortConfigEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.2.1.6 msanDhcpRaPortCircuitType OBJECT-TYPE SYNTAX INTEGER { trusted(1), untrusted(2), notConfigured(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies DHCP RA Circuit type per port as trusted(1) or untrusted(2)." DEFVAL { notConfigured } ::= { msanDhcpRaPortConfigEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.2.1.7 msanDhcpRaPortOpt82 OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2), notConfigured(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies DHCP Relay Agent option 82 insertion status per port." DEFVAL { notConfigured } ::= { msanDhcpRaPortConfigEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.2.1.8 msanDhcpRaPortOpt82ReplyMode OBJECT-TYPE SYNTAX INTEGER { keep(1), remove(2), notConfigured(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies DHCP Relay Agent keep/remove option 82 in replies per port." DEFVAL { notConfigured } ::= { msanDhcpRaPortConfigEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.2.1.9 msanDhcpRaPortOpt82UnicastExtStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2), notConfigured(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The desired state of insertion of option 82 in unicast frames per port." DEFVAL { notConfigured } ::= { msanDhcpRaPortConfigEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.2.1.10 msanDhcpRaPortCircuitIdType OBJECT-TYPE SYNTAX INTEGER { iskratel(1), standard(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Circuit Id syntax mode per port." DEFVAL { iskratel } ::= { msanDhcpRaPortConfigEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.3 msanDhcpRaFullModeVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanDhcpRaFullModeVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanDhcpRelay 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.3.1 msanDhcpRaFullModeVlanEntry OBJECT-TYPE SYNTAX MsanDhcpRaFullModeVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanDhcpRaFullModeVlanId, msanDhcpRaFullModeVlanSrvIpAddr } ::= { msanDhcpRaFullModeVlanTable 1 } MsanDhcpRaFullModeVlanEntry ::= SEQUENCE { msanDhcpRaFullModeVlanId Integer32, msanDhcpRaFullModeVlanSrvIpAddr IpAddress, msanDhcpRaFullModeVlanRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.4.3.1.1 msanDhcpRaFullModeVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN identifier (refers to dot1qVlanIndex) where DHCP Client resides." ::= { msanDhcpRaFullModeVlanEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.3.1.2 msanDhcpRaFullModeVlanSrvIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of DHCP Server for specified VLAN." ::= { msanDhcpRaFullModeVlanEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.3.1.3 msanDhcpRaFullModeVlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanDhcpRaFullModeVlanEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.5 msanDhcpRaStatTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanDhcpRaStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanDhcpRelay 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.5.1 msanDhcpRaStatEntry OBJECT-TYPE SYNTAX MsanDhcpRaStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanDhcpRaStatTable 1 } MsanDhcpRaStatEntry ::= SEQUENCE { msanDhcpRaStatDiscover Counter32, msanDhcpRaStatRequest Counter32, msanDhcpRaStatOffer Counter32, msanDhcpRaStatACK Counter32, msanDhcpRaStatNAK Counter32, msanDhcpRaStatDecline Counter32, msanDhcpRaStatMaxPacketSizeExceeded Counter32, msanDhcpRaStatFrameErr Counter32, msanDhcpRaStatOpt82Present Counter32, msanDhcpRaStatFrameUnsync Counter32, msanDhcpRaStatRelease Counter32, msanDhcpRaStatInform Counter32 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.5.1.1 msanDhcpRaStatDiscover OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCP DISCOVER packets." ::= { msanDhcpRaStatEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.5.1.2 msanDhcpRaStatRequest OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCP REQUEST packets." ::= { msanDhcpRaStatEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.5.1.3 msanDhcpRaStatOffer OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCP OFFER packets." ::= { msanDhcpRaStatEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.5.1.4 msanDhcpRaStatACK OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCP ACKNOWLAGE (ACK) packets." ::= { msanDhcpRaStatEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.5.1.5 msanDhcpRaStatNAK OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCP NOT ACKNOWLAGE (NAK) packets." ::= { msanDhcpRaStatEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.5.1.6 msanDhcpRaStatDecline OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCP DECLINE packets." ::= { msanDhcpRaStatEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.5.1.7 msanDhcpRaStatMaxPacketSizeExceeded OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCP packets with max. packet size exceeded. " ::= { msanDhcpRaStatEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.5.1.8 msanDhcpRaStatFrameErr OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCP packets with errors in frames. " ::= { msanDhcpRaStatEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.5.1.9 msanDhcpRaStatOpt82Present OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCP packets with Option 82 or giaddr present. " ::= { msanDhcpRaStatEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.5.1.10 msanDhcpRaStatFrameUnsync OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received packets with frames not synchronized with state machines." ::= { msanDhcpRaStatEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.5.1.11 msanDhcpRaStatRelease OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCP RELEASE packets." ::= { msanDhcpRaStatEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.5.1.12 msanDhcpRaStatInform OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCP INFORM packets." ::= { msanDhcpRaStatEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.6 msanDhcpRaVlanConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanDhcpRaVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table od DHCP RA parameters per Vlan." ::= { msanDhcpRelay 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.6.1 msanDhcpRaVlanConfigEntry OBJECT-TYPE SYNTAX MsanDhcpRaVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { dot1qVlanIndex } ::= { msanDhcpRaVlanConfigTable 1 } MsanDhcpRaVlanConfigEntry ::= SEQUENCE { msanDhcpRaVlanState INTEGER, msanDhcpRaVlanMode INTEGER, msanDhcpRaVlanOpt82 INTEGER, msanDhcpRaVlanOpt82ReplyMode INTEGER, msanDhcpRaVlanOpt82UnicastExtStatus INTEGER, msanDhcpRaVlanCircuitIdType INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.4.6.1.1 msanDhcpRaVlanState OBJECT-TYPE SYNTAX INTEGER { disable(1), notConfigured(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "DHCP RA state for specified VLAN ID. Value notConfigured(2) means, that global setting is used(msanDhcpRaStatus)." DEFVAL { notConfigured } ::= { msanDhcpRaVlanConfigEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.6.1.2 msanDhcpRaVlanMode OBJECT-TYPE SYNTAX INTEGER { full(1), simplified(2), notConfigured(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "DHCP RA mode for specified VLAN ID. Value notConfigured(1) means, that global setting is used(msanDhcpRaMode)." DEFVAL { notConfigured } ::= { msanDhcpRaVlanConfigEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.6.1.3 msanDhcpRaVlanOpt82 OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2), notConfigured(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies DHCP Relay Agent option 82 insertion status per vlan." DEFVAL { notConfigured } ::= { msanDhcpRaVlanConfigEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.6.1.4 msanDhcpRaVlanOpt82ReplyMode OBJECT-TYPE SYNTAX INTEGER { keep(1), remove(2), notConfigured(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies DHCP Relay Agent keep/remove option 82 in replies per vlan." DEFVAL { notConfigured } ::= { msanDhcpRaVlanConfigEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.6.1.5 msanDhcpRaVlanOpt82UnicastExtStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2), notConfigured(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The desired state of insertion of option 82 in unicast frames per vlan." DEFVAL { notConfigured } ::= { msanDhcpRaVlanConfigEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.6.1.6 msanDhcpRaVlanCircuitIdType OBJECT-TYPE SYNTAX INTEGER { iskratel(1), standard(2), notConfigured(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Circuit Id syntax mode per vlan." DEFVAL { notConfigured } ::= { msanDhcpRaVlanConfigEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.7 msanDhcpRaPortVlanConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanDhcpRaPortVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanDhcpRelay 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.7.1 msanDhcpRaPortVlanConfigEntry OBJECT-TYPE SYNTAX MsanDhcpRaPortVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex, dot1qVlanIndex } ::= { msanDhcpRaPortVlanConfigTable 1 } MsanDhcpRaPortVlanConfigEntry ::= SEQUENCE { msanDhcpRaPortVlanRemoteId OCTET STRING, msanDhcpRaPortVlanConfigRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.4.7.1.1 msanDhcpRaPortVlanRemoteId OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN identifier (refers to dot1qVlanIndex) where DHCP Client resides." DEFVAL { "" } ::= { msanDhcpRaPortVlanConfigEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.7.1.2 msanDhcpRaPortVlanConfigRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported]." ::= { msanDhcpRaPortVlanConfigEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.100 msanDhcpv6RaGlobal OBJECT IDENTIFIER ::= { msanDhcpRelay 100 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.100.1 msanDhcpv6RaState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "DHCPv6 Relay Agent status." DEFVAL { disable } ::= { msanDhcpv6RaGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.100.2 msanDhcpv6RaMode OBJECT-TYPE SYNTAX INTEGER { ldra(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "DHCPv6 Relay Agent mode. ldra = Lightweight DHCPRv6" DEFVAL { ldra } ::= { msanDhcpv6RaGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.100.3 msanDhcpv6RaInterfaceIdStandard OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "DHCPv6 RA Standard Interface Id type." DEFVAL { enable } ::= { msanDhcpv6RaGlobal 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101 msanDhcpv6Statistics OBJECT IDENTIFIER ::= { msanDhcpRelay 101 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.1 msanDhcpv6RaPortStatTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanDhcpv6RaPortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanDhcpv6Statistics 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1 msanDhcpv6RaPortStatEntry OBJECT-TYPE SYNTAX MsanDhcpv6RaPortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanDhcpv6RaPortStatTable 1 } MsanDhcpv6RaPortStatEntry ::= SEQUENCE { msanDhcpv6PortRaStatSolicit Integer32, msanDhcpv6PortRaStatAdvertise Integer32, msanDhcpv6PortRaStatRequest Integer32, msanDhcpv6PortRaStatReply Integer32, msanDhcpv6PortRaStatRenew Integer32, msanDhcpv6PortRaStatRebind Integer32, msanDhcpv6PortRaStatDecline Integer32, msanDhcpv6PortRaStatReconfigure Integer32, msanDhcpv6PortRaStatRelease Integer32, msanDhcpv6PortRaStatInformRequest Integer32, msanDhcpv6PortRaStatRelayForward Integer32, msanDhcpv6PortRaStatRelayReply Integer32, msanDhcpv6PortRaStatOversizeError Integer32, msanDhcpv6PortRaStatFrameError Integer32, msanDhcpv6PortRaStatFrameUnsyncError Integer32, msanDhcpv6PortRaStatSysError Integer32 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.1 msanDhcpv6PortRaStatSolicit OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 solicit packets." ::= { msanDhcpv6RaPortStatEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.2 msanDhcpv6PortRaStatAdvertise OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 advertise packets." ::= { msanDhcpv6RaPortStatEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.3 msanDhcpv6PortRaStatRequest OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 request packets." ::= { msanDhcpv6RaPortStatEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.4 msanDhcpv6PortRaStatReply OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 reply packets." ::= { msanDhcpv6RaPortStatEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.5 msanDhcpv6PortRaStatRenew OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 renew packets." ::= { msanDhcpv6RaPortStatEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.6 msanDhcpv6PortRaStatRebind OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 rebind packets." ::= { msanDhcpv6RaPortStatEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.7 msanDhcpv6PortRaStatDecline OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 decline packets." ::= { msanDhcpv6RaPortStatEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.8 msanDhcpv6PortRaStatReconfigure OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 reconfigure packets." ::= { msanDhcpv6RaPortStatEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.9 msanDhcpv6PortRaStatRelease OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 release packets." ::= { msanDhcpv6RaPortStatEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.10 msanDhcpv6PortRaStatInformRequest OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 inform request packets." ::= { msanDhcpv6RaPortStatEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.11 msanDhcpv6PortRaStatRelayForward OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 relay forward packets." ::= { msanDhcpv6RaPortStatEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.12 msanDhcpv6PortRaStatRelayReply OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 relay reply packets." ::= { msanDhcpv6RaPortStatEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.100 msanDhcpv6PortRaStatOversizeError OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of discarded packets because max packet size exceeded." ::= { msanDhcpv6RaPortStatEntry 100 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.101 msanDhcpv6PortRaStatFrameError OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of discarded packets because frame error." ::= { msanDhcpv6RaPortStatEntry 101 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.102 msanDhcpv6PortRaStatFrameUnsyncError OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received packets with frames not synchronized with state machines." ::= { msanDhcpv6RaPortStatEntry 102 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.103 msanDhcpv6PortRaStatSysError OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of discarded packets because system error." ::= { msanDhcpv6RaPortStatEntry 103 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.100 msanDhcpv6RaStatSolicit OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 solicit packets." ::= { msanDhcpv6Statistics 100 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.101 msanDhcpv6RaStatAdvertise OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 advertise packets." ::= { msanDhcpv6Statistics 101 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.102 msanDhcpv6RaStatRequest OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 request packets." ::= { msanDhcpv6Statistics 102 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.103 msanDhcpv6RaStatReply OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 reply packets." ::= { msanDhcpv6Statistics 103 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.104 msanDhcpv6RaStatRenew OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 renew packets." ::= { msanDhcpv6Statistics 104 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.105 msanDhcpv6RaStatRebind OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 rebind packets." ::= { msanDhcpv6Statistics 105 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.106 msanDhcpv6RaStatDecline OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 decline packets." ::= { msanDhcpv6Statistics 106 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.107 msanDhcpv6RaStatReconfigure OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 reconfigure packets." ::= { msanDhcpv6Statistics 107 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.108 msanDhcpv6RaStatRelease OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 reconfigure packets." ::= { msanDhcpv6Statistics 108 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.109 msanDhcpv6RaStatInformRequest OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 inform request packets." ::= { msanDhcpv6Statistics 109 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.110 msanDhcpv6RaStatRelayForward OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 Relay Forward packets." ::= { msanDhcpv6Statistics 110 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.112 msanDhcpv6RaStatRelayReply OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received DHCPv6 Relay Reply packets." ::= { msanDhcpv6Statistics 112 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.200 msanDhcpv6RaStatOversizeError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of discarded packets because max packet size exceeded." ::= { msanDhcpv6Statistics 200 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.201 msanDhcpv6RaStatFrameError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of discareded packets because errors in frame." ::= { msanDhcpv6Statistics 201 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.202 msanDhcpv6RaStatFrameUnsyncError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received packets with frames not synchronized with state machines." ::= { msanDhcpv6Statistics 202 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.101.203 msanDhcpv6RaStatSysError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of discared packets because system error." ::= { msanDhcpv6Statistics 203 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.102 msanDhcpv6RaPortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanDhcpv6RaPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table od DHCP RA parameters per port." ::= { msanDhcpRelay 102 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.102.1 msanDhcpv6RaPortConfigEntry OBJECT-TYPE SYNTAX MsanDhcpv6RaPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanDhcpv6RaPortConfigTable 1 } MsanDhcpv6RaPortConfigEntry ::= SEQUENCE { msanDhcpv6RaPortState INTEGER, msanDhcpv6RaPortTrusted INTEGER, msanDhcpv6RaPortInterfaceIdStandard INTEGER, msanDhcpv6RaPortInterfaceId OCTET STRING, msanDhcpv6RaPortRemoteId OCTET STRING, msanDhcpv6RaPortRemoteIdEnterpriseNum INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.4.102.1.1 msanDhcpv6RaPortState OBJECT-TYPE SYNTAX INTEGER { enable(1), enableCli(2), enableSrv(3), disable(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "State of DHCPv6 Relay Agent on the port (enable, disable, enable-client, enable-server) " DEFVAL { enable } ::= { msanDhcpv6RaPortConfigEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.102.1.2 msanDhcpv6RaPortTrusted OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies DHCP RA Circuit type per port as trusted(1) or untrusted(2). Default value for user ports is untrusted(2) and for network ports trusted(1). " ::= { msanDhcpv6RaPortConfigEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.102.1.3 msanDhcpv6RaPortInterfaceIdStandard OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "DHCPv6 RA Circuit Id syntax mode per port." DEFVAL { enable } ::= { msanDhcpv6RaPortConfigEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.102.1.4 msanDhcpv6RaPortInterfaceId OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "DHCPv6 Option 82 Circuit Id for the port." ::= { msanDhcpv6RaPortConfigEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.102.1.5 msanDhcpv6RaPortRemoteId OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "DHCPv6 Remote Id value for the port. If empty string, remote id is not added to DHCPv6 package." DEFVAL { "" } ::= { msanDhcpv6RaPortConfigEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.102.1.6 msanDhcpv6RaPortRemoteIdEnterpriseNum OBJECT-TYPE SYNTAX INTEGER (1..999999) MAX-ACCESS read-write STATUS current DESCRIPTION "DHCPv6 Remote Id enterprise number for the port. " DEFVAL { 1332 } ::= { msanDhcpv6RaPortConfigEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.103 msanDhcpv6RaVlanConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanDhcpv6RaVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table od DHCP RA parameters per Vlan." ::= { msanDhcpRelay 103 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.103.1 msanDhcpv6RaVlanConfigEntry OBJECT-TYPE SYNTAX MsanDhcpv6RaVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { dot1qVlanIndex } ::= { msanDhcpv6RaVlanConfigTable 1 } MsanDhcpv6RaVlanConfigEntry ::= SEQUENCE { msanDhcpv6RaVlanState INTEGER, msanDhcpv6RaVlanInterfaceIdStandard INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.4.103.1.1 msanDhcpv6RaVlanState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "DHCP RA state for specified VLAN ID. " DEFVAL { enable } ::= { msanDhcpv6RaVlanConfigEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.103.1.2 msanDhcpv6RaVlanInterfaceIdStandard OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "DHCPv6 RA Circuit Id syntax mode per port." DEFVAL { enable } ::= { msanDhcpv6RaVlanConfigEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.104 msanDhcpv6RaPortVlanConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanDhcpv6RaPortVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanDhcpRelay 104 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.104.1 msanDhcpv6RaPortVlanConfigEntry OBJECT-TYPE SYNTAX MsanDhcpv6RaPortVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex, dot1qVlanIndex } ::= { msanDhcpv6RaPortVlanConfigTable 1 } MsanDhcpv6RaPortVlanConfigEntry ::= SEQUENCE { msanDhcpv6RaPortVlanRemoteId OCTET STRING, msanDhcpv6RaPortVlanRemoteIdEnterpriseNum INTEGER, msanDhcpv6RaPortVlanRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.4.104.1.1 msanDhcpv6RaPortVlanRemoteId OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "DHCPv6 Remote Id value for specified vlan_id per port. " DEFVAL { "" } ::= { msanDhcpv6RaPortVlanConfigEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.104.1.2 msanDhcpv6RaPortVlanRemoteIdEnterpriseNum OBJECT-TYPE SYNTAX INTEGER (1..999999) MAX-ACCESS read-write STATUS current DESCRIPTION "DHCPv6 Remote Id enterprise number for specified vlan_id per port. " DEFVAL { 1332 } ::= { msanDhcpv6RaPortVlanConfigEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.4.104.1.3 msanDhcpv6RaPortVlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported]." ::= { msanDhcpv6RaPortVlanConfigEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.5 msanSntp OBJECT IDENTIFIER ::= { msanAdditionalConf 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.5.1 msanSntpGlobal OBJECT IDENTIFIER ::= { msanSntp 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.5.1.1 msanSntpTzOffset OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the time zone offset time in format hh:mm. Allowed range is -12 to 13." ::= { msanSntpGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.5.1.2 msanSntpTzName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "Time Zone name." ::= { msanSntpGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.5.1.3 msanSntpTzDstOffset OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the daylight saving time offset time in format hh:mm. Allowed range is -12 to 13." ::= { msanSntpGlobal 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.5.1.4 msanSntpTzDstStartMonth OBJECT-TYPE SYNTAX Integer32 (1..12) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the daylight saving time start month. " ::= { msanSntpGlobal 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.5.1.5 msanSntpTzDstStartWeek OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the daylight saving time start week." ::= { msanSntpGlobal 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.5.1.6 msanSntpTzDstStartDayInWeek OBJECT-TYPE SYNTAX INTEGER { monday(1), tuesday(2), wednesday(3), thursday(4), friday(5), saturday(6), sunday(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the daylight saving time start day in week." ::= { msanSntpGlobal 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.5.1.7 msanSntpTzDstStartTime OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the daylight saving time start time. Allowed range is 00:00 to 23:59." ::= { msanSntpGlobal 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.5.1.8 msanSntpTzDstEndMonth OBJECT-TYPE SYNTAX Integer32 (1..12) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the daylight saving time end month." ::= { msanSntpGlobal 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.5.1.9 msanSntpTzDstEndWeek OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the daylight saving time end week." ::= { msanSntpGlobal 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.5.1.10 msanSntpTzDstEndDayInWeek OBJECT-TYPE SYNTAX INTEGER { monday(1), tuesday(2), wednesday(3), thursday(4), friday(5), saturday(6), sunday(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the daylight saving time end start day in week." ::= { msanSntpGlobal 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.5.1.11 msanSntpTzDstEndTime OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the daylight saving time end time. Allowed range is 00:00 to 23:59" ::= { msanSntpGlobal 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.7 msanSnmp OBJECT IDENTIFIER ::= { msanAdditionalConf 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.7.1 msanSnmpGlobal OBJECT IDENTIFIER ::= { msanSnmp 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.7.1.1 msanSnmpTrapRecvUdpPort OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The UDP Port where SNMP traps are to be sent." ::= { msanSnmpGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.8 msanIgmpSnooping OBJECT IDENTIFIER ::= { msanAdditionalConf 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.1 msanIgmpSnoopingGlobal OBJECT IDENTIFIER ::= { msanIgmpSnooping 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.1.1 msanIgmpSnoopingReportSuppression OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Report suppression mode for IGMP Snooping for the switch. " ::= { msanIgmpSnoopingGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.1.2 msanIgmpSnoopingAdminState OBJECT-TYPE SYNTAX INTEGER { disableAndDiscard(0), disableAndBroadcast(1), enable(2), enableAndUnknownGroupFlood(3), enableAndMrouterFlood(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "IGMP snooping global state. Values enableAndUnknownGroupFlood(3) and enableAndMrouterFlood(4) are relevant only for MSAN Ethernet switch (ES) products, where enableAndUnknownGroupFlood(3) is supported only on IDC board." ::= { msanIgmpSnoopingGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.1.3 msanIgmpSnoopingLoggingVlanId OBJECT-TYPE SYNTAX Integer32 (0..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "VLAN Id on which IGMP snooping logging is performed. Value 0 means that logging is disabled. " ::= { msanIgmpSnoopingGlobal 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.1.4 msanIgmpSnoopingViolationAction OBJECT-TYPE SYNTAX INTEGER { remove(1), discard(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Removing one of the existing (the oldest) multicast group membership, or discarding a new group membership request. " ::= { msanIgmpSnoopingGlobal 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.1.5 msanIgmpSnoopingFastLeaveAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This enables or disables IGMP Snooping Fast-Leave on user ports." DEFVAL { enable } ::= { msanIgmpSnoopingGlobal 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.1.6 msanIgmpSnoopingGroupMembershipInterval OBJECT-TYPE SYNTAX Integer32 (2..3600) MAX-ACCESS read-write STATUS current DESCRIPTION "The amount of time in seconds that a switch will wait for a report from a particular group on the selected interface before deleting the interface from the entry. This value must be greater than msanIgmpSnoopingMaxResponseTime " DEFVAL { 260 } ::= { msanIgmpSnoopingGlobal 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.1.7 msanIgmpSnoopingMaxResponseTime OBJECT-TYPE SYNTAX Integer32 (1..3599) MAX-ACCESS read-write STATUS current DESCRIPTION "The amount of time in seconds a switch will wait on a report after sending a query on the selected interface. This value must be less than msanIgmpSnoopingGroupMembershipInterval " DEFVAL { '10'b } ::= { msanIgmpSnoopingGlobal 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.1.8 msanIgmpVersion OBJECT-TYPE SYNTAX INTEGER { igmpAll(1), igmpVersion2(2), igmpVersion3(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Version of processed IGMP frames." DEFVAL { igmpAll } ::= { msanIgmpSnoopingGlobal 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.1.9 msanIgmpClear OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear all IGMP snooping entries." ::= { msanIgmpSnoopingGlobal 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.2 msanIgmpSnoopingTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanIgmpSnoopingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanIgmpSnooping 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.2.1 msanIgmpSnoopingEntry OBJECT-TYPE SYNTAX MsanIgmpSnoopingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanIgmpSnoopingTable 1 } MsanIgmpSnoopingEntry ::= SEQUENCE { msanIgmpSnoopingIntfStandaloneQuerier Integer32, msanIgmpSnoopingIntfFilter INTEGER, msanIgmpSnoopingGroupLimit INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.8.2.1.1 msanIgmpSnoopingIntfStandaloneQuerier OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the period of time in seconds you want the IGMP Standalone Querier generate IGMP query packets. Value must be higher than msanIgmpSnoopingMaxResponseTime and lower than msanIgmpSnoopingGroupMembershipInterval or 0. The default is 0. A value of zero indicates that standalone querier is disabled. IGMP SA Querier can be activated only on one interface at the same time. " ::= { msanIgmpSnoopingEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.2.1.2 msanIgmpSnoopingIntfFilter OBJECT-TYPE SYNTAX INTEGER { allowAll(0), allowReports(1), allowQueries(2), dropAll(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Filtering of IGMP join/leave reports or queries frames. " ::= { msanIgmpSnoopingEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.2.1.3 msanIgmpSnoopingGroupLimit OBJECT-TYPE SYNTAX INTEGER (0..10) MAX-ACCESS read-write STATUS current DESCRIPTION "A maximum numbers of IGMP groups per interface. Value 0 means no limits." ::= { msanIgmpSnoopingEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.3 msanSwitchIGMPVlanCurrentMrouterTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanSwitchIGMPVlanCurrentMrouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanIgmpSnooping 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.3.1 msanSwitchIGMPVlanCurrentMrouterEntry OBJECT-TYPE SYNTAX MsanSwitchIGMPVlanCurrentMrouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex, dot1qVlanIndex } ::= { msanSwitchIGMPVlanCurrentMrouterTable 1 } MsanSwitchIGMPVlanCurrentMrouterEntry ::= SEQUENCE { msanSwitchIGMPVlanCurrentMrouterEnableState Integer32 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.3.1.1 msanSwitchIGMPVlanCurrentMrouterEnableState OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Returns per-interface per-vlan pairs where IGMP Mrouter is enabled. " ::= { msanSwitchIGMPVlanCurrentMrouterEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.4 msanSwitchIGMPSnoopingStaticIntfMulticastRouterTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanSwitchIGMPSnoopingStaticIntfMulticastRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." REFERENCE "agentSwitchIGMPSnoopingIntfTable - 1.3.6.1.4.1.6132.1.1.1.2.8.7.1" ::= { msanIgmpSnooping 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.4.1 msanSwitchIGMPSnoopingStaticIntfMulticastRouterEntry OBJECT-TYPE SYNTAX MsanSwitchIGMPSnoopingStaticIntfMulticastRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanSwitchIGMPSnoopingStaticIntfMulticastRouterTable 1 } MsanSwitchIGMPSnoopingStaticIntfMulticastRouterEntry ::= SEQUENCE { msanSwitchIGMPSnoopingIntfIndex Unsigned32, msanSwitchIGMPSnoopingIntfAdminMode INTEGER, msanSwitchIGMPSnoopingIntfGroupMembershipInterval Integer32, msanSwitchIGMPSnoopingIntfMaxResponseTime Integer32, msanSwitchIGMPSnoopingIntfMRPExpirationTime Integer32, msanSwitchIGMPSnoopingIntfFastLeaveAdminMode INTEGER, msanSwitchIGMPSnoopingStaticIntfMulticastRouterMode INTEGER, msanSwitchIGMPSnoopingIntfVlanIDs VlanList } -- 1.3.6.1.4.1.1332.1.1.5.3.8.4.1.1 msanSwitchIGMPSnoopingIntfIndex OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The port number to be selected. Each port maps to an interface." ::= { msanSwitchIGMPSnoopingStaticIntfMulticastRouterEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.4.1.2 msanSwitchIGMPSnoopingIntfAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This enables or disables IGMP Snooping on a selected interface." DEFVAL { disable } ::= { msanSwitchIGMPSnoopingStaticIntfMulticastRouterEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.4.1.3 msanSwitchIGMPSnoopingIntfGroupMembershipInterval OBJECT-TYPE SYNTAX Integer32 (2..3600) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The amount of time in seconds that a switch will wait for a report from a particular group on the selected interface before deleting the interface from the entry. This value must be greater than agentSwitchIGMPSnoopingIntfMaxResponseTime." DEFVAL { 260 } ::= { msanSwitchIGMPSnoopingStaticIntfMulticastRouterEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.4.1.4 msanSwitchIGMPSnoopingIntfMaxResponseTime OBJECT-TYPE SYNTAX Integer32 (1..3599) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The amount of time in seconds a switch will wait after sending a query on the selected interface because it did not receive a report for a particular group in that interface. This value must be less than agentSwitchIGMPSnoopingIntfGroupMembershipInterval." DEFVAL { 10 } ::= { msanSwitchIGMPSnoopingStaticIntfMulticastRouterEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.4.1.5 msanSwitchIGMPSnoopingIntfMRPExpirationTime OBJECT-TYPE SYNTAX Integer32 (0..3600) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The amount of time in seconds that a switch will wait for a query to be received on the selected interface before the interface is removed from the list of interfaces with multicast routers attached." DEFVAL { 0 } ::= { msanSwitchIGMPSnoopingStaticIntfMulticastRouterEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.4.1.6 msanSwitchIGMPSnoopingIntfFastLeaveAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This enables or disables IGMP Snooping Fast-Leave on specified interface." DEFVAL { disable } ::= { msanSwitchIGMPSnoopingStaticIntfMulticastRouterEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.4.1.7 msanSwitchIGMPSnoopingStaticIntfMulticastRouterMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Mode of static IGMP Mrouter on selected interface." ::= { msanSwitchIGMPSnoopingStaticIntfMulticastRouterEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.4.1.8 msanSwitchIGMPSnoopingIntfVlanIDs OBJECT-TYPE SYNTAX VlanList MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This field lists all the VlanIDs which include the selected interface." ::= { msanSwitchIGMPSnoopingStaticIntfMulticastRouterEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.5 msanSwitchIGMPVlanStaticMrouterTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanSwitchIGMPVlanStaticMrouterEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." ::= { msanIgmpSnooping 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.5.1 msanSwitchIGMPVlanStaticMrouterEntry OBJECT-TYPE SYNTAX MsanSwitchIGMPVlanStaticMrouterEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." INDEX { ifIndex, dot1qVlanIndex } ::= { msanSwitchIGMPVlanStaticMrouterTable 1 } MsanSwitchIGMPVlanStaticMrouterEntry ::= SEQUENCE { msanSwitchIGMPVlanStaticMrouterEnableState RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.8.5.1.1 msanSwitchIGMPVlanStaticMrouterEnableState OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "Object used to create a new row or modify or destroy an existing row in manner described in the definition of the RowStatus textual. Supported states are Active(1), CreateAndGo(4) and Destroy(6). Row is created with CreateAndGo(4). This enables IGMP Mrouter on a per-interface per-vlan basis and the row goes to Active(1). The row is removed with Destroy(6) and IGMP Mrouter on this interface/VLAN pair is disabled. Values NotInService(2), NotReady(3) and CreateAndWait(5) are not supported." ::= { msanSwitchIGMPVlanStaticMrouterEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.6 msanSwitchIGMPSnoopingVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanSwitchIGMPSnoopingVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the IGMP Snooping Vlan configuration entries." REFERENCE "agentSwitchIGMPSnoopingVlanTable - 1.3.6.1.4.1.6132.1.1.1.2.8.8.1" ::= { msanIgmpSnooping 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.6.1 msanSwitchIGMPSnoopingVlanEntry OBJECT-TYPE SYNTAX MsanSwitchIGMPSnoopingVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Represents entry for a IGMP Snooping Vlan." INDEX { dot1qVlanIndex } ::= { msanSwitchIGMPSnoopingVlanTable 1 } MsanSwitchIGMPSnoopingVlanEntry ::= SEQUENCE { msanSwitchIGMPSnoopingVlanAdminMode INTEGER, msanSwitchIGMPSnoopingVlanGroupMembershipInterval Integer32, msanSwitchIGMPSnoopingVlanMaxResponseTime Integer32, msanSwitchIGMPSnoopingVlanFastLeaveAdminMode INTEGER, msanSwitchIGMPSnoopingVlanMRPExpirationTime Integer32, msanSwitchIGMPSnoopingVlanAdminState INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.8.6.1.1 msanSwitchIGMPSnoopingVlanAdminMode OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This enables or disables IGMP Snooping on a selected Vlan interface." DEFVAL { disable } ::= { msanSwitchIGMPSnoopingVlanEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.6.1.2 msanSwitchIGMPSnoopingVlanGroupMembershipInterval OBJECT-TYPE SYNTAX Integer32 (2..3600) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The amount of time in seconds that a switch will wait for a report from a particular group on the selected vlan before deleting the interface participating in the vlan from the entry. This value must be greater than agentSwitchIGMPSnoopingIntfMaxResponseTime." DEFVAL { 260 } ::= { msanSwitchIGMPSnoopingVlanEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.6.1.3 msanSwitchIGMPSnoopingVlanMaxResponseTime OBJECT-TYPE SYNTAX Integer32 (1..3599) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The amount of time in seconds a switch will wait after sending a query on the selected vlan because it did not receive a report for a particular group in the interface participating in the vlan. This value must be less than agentSwitchIGMPSnoopingIntfGroupMembershipInterval." DEFVAL { 10 } ::= { msanSwitchIGMPSnoopingVlanEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.6.1.4 msanSwitchIGMPSnoopingVlanFastLeaveAdminMode OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This enables or disables IGMP Snooping on the selected vlan." DEFVAL { disable } ::= { msanSwitchIGMPSnoopingVlanEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.6.1.5 msanSwitchIGMPSnoopingVlanMRPExpirationTime OBJECT-TYPE SYNTAX Integer32 (0..3600) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The amount of time in seconds that a switch will wait for a query to be received on the selected interface participating in the vlan before the interface is removed from the list of interfaces with multicast routers attached. This parameter is configurable only for exisiting Vlans." DEFVAL { 0 } ::= { msanSwitchIGMPSnoopingVlanEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.6.1.6 msanSwitchIGMPSnoopingVlanAdminState OBJECT-TYPE SYNTAX INTEGER { disableAndDiscard(0), disableAndBroadcast(1), enable(2), enableAndUnknownGroupFlood(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "IGMP Snooping state on a selected Vlan interface. This parameter is ignored if global msanIgmpSnoopingAdminState value is disableAndDiscard(0) or disableAndBroadcast(1)." DEFVAL { disableAndDiscard } ::= { msanSwitchIGMPSnoopingVlanEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.7 msanSwitchIGMPProxyVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanSwitchIGMPProxyVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the IGMP Proxy Vlan configuration entries." ::= { msanIgmpSnooping 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.7.1 msanSwitchIGMPProxyVlanEntry OBJECT-TYPE SYNTAX MsanSwitchIGMPProxyVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " " INDEX { dot1qVlanIndex, msanSwitchIGMPProxyVlanIpAddr } ::= { msanSwitchIGMPProxyVlanTable 1 } MsanSwitchIGMPProxyVlanEntry ::= SEQUENCE { msanSwitchIGMPProxyVlanIpAddr IpAddress, msanSwitchIGMPProxyVlanRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.8.7.1.1 msanSwitchIGMPProxyVlanIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "IGMP Proxy IP address. If set to 0.0.0.0, default IP address is used (IP address of MN interface -> msanNetworkIPAddress)." ::= { msanSwitchIGMPProxyVlanEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.7.1.2 msanSwitchIGMPProxyVlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanSwitchIGMPProxyVlanEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8 msanIgmpStatistics OBJECT IDENTIFIER ::= { msanIgmpSnooping 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.1 msanIgmpStatGlobal OBJECT IDENTIFIER ::= { msanIgmpStatistics 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.1.1 msanIgmpStatRxV1 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received IGMP v1 packets." ::= { msanIgmpStatGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.1.2 msanIgmpStatRxV2Join OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received IGMP v2 join packets." ::= { msanIgmpStatGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.1.3 msanIgmpStatRxV2Leave OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received IGMP v2 leave packets." ::= { msanIgmpStatGlobal 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.1.4 msanIgmpStatRxV3Report OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received IGMP v3 report packets." ::= { msanIgmpStatGlobal 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.1.5 msanIgmpStatRxQuery OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received IGMP query packets." ::= { msanIgmpStatGlobal 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.1.6 msanIgmpStatRxError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received corrupted or unknown IGMP packets." ::= { msanIgmpStatGlobal 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.1.7 msanIgmpStatRxBlockByIgmpFilter OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received IGMP packets blocked by IGMP filter." ::= { msanIgmpStatGlobal 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.1.8 msanIgmpStatRxBlockByMcastAcl OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received IGMP packets blocked by Multicast ACL." ::= { msanIgmpStatGlobal 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.1.9 msanIgmpStatRxBlockByMcastCac OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received IGMP packets blocked by Multicast CAC." ::= { msanIgmpStatGlobal 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.1.10 msanIgmpStatRxBlockByIgmpVersion OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received IGMP packets blocked by IGMP Version Control." ::= { msanIgmpStatGlobal 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.2 msanIgmpPortStatTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanIgmpPortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanIgmpStatistics 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1 msanIgmpPortStatEntry OBJECT-TYPE SYNTAX MsanIgmpPortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanIgmpPortStatTable 1 } MsanIgmpPortStatEntry ::= SEQUENCE { msanIgmpPortStatRxV1 Counter32, msanIgmpPortStatTxV1 Counter32, msanIgmpPortStatRxV2Join Counter32, msanIgmpPortStatTxV2Join Counter32, msanIgmpPortStatRxV2Leave Counter32, msanIgmpPortStatTxV2Leave Counter32, msanIgmpPortStatRxV3Report Counter32, msanIgmpPortStatTxV3Report Counter32, msanIgmpPortStatRxQuery Counter32, msanIgmpPortStatRxError Counter32, msanIgmpPortStatRxBlockByIgmpFilter Counter32, msanIgmpPortStatRxBlockByMcastAcl Counter32, msanIgmpPortStatRxBlockByMcastCac Counter32, msanIgmpPortStatTxQuery Counter32, msanIgmpPortStatRxBlockByIgmpVersion Counter32 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.1 msanIgmpPortStatRxV1 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received IGMP v1 packets." ::= { msanIgmpPortStatEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.2 msanIgmpPortStatTxV1 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of transmitted IGMP v1 packets." ::= { msanIgmpPortStatEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.3 msanIgmpPortStatRxV2Join OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received IGMP v2 join packets." ::= { msanIgmpPortStatEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.4 msanIgmpPortStatTxV2Join OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of transmitted IGMP v2 join packets." ::= { msanIgmpPortStatEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.5 msanIgmpPortStatRxV2Leave OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received IGMP v2 leave packets." ::= { msanIgmpPortStatEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.6 msanIgmpPortStatTxV2Leave OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of transmitted IGMP v2 leave packets." ::= { msanIgmpPortStatEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.7 msanIgmpPortStatRxV3Report OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received IGMP v3 report packets." ::= { msanIgmpPortStatEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.8 msanIgmpPortStatTxV3Report OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of transmitted IGMP v3 report packets." ::= { msanIgmpPortStatEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.9 msanIgmpPortStatRxQuery OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received IGMP query packets." ::= { msanIgmpPortStatEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.10 msanIgmpPortStatRxError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received corrupted or unknown IGMP packets." ::= { msanIgmpPortStatEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.11 msanIgmpPortStatRxBlockByIgmpFilter OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received IGMP packets blocked by IGMP filter." ::= { msanIgmpPortStatEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.12 msanIgmpPortStatRxBlockByMcastAcl OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received IGMP packets blocked by Multicast ACL." ::= { msanIgmpPortStatEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.13 msanIgmpPortStatRxBlockByMcastCac OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received IGMP packets blocked by Multicast CAC." ::= { msanIgmpPortStatEntry 13 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.14 msanIgmpPortStatTxQuery OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of transmitted IGMP query packets." ::= { msanIgmpPortStatEntry 14 } -- 1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.15 msanIgmpPortStatRxBlockByIgmpVersion OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received IGMP packets blocked by IGMP Version." ::= { msanIgmpPortStatEntry 15 } -- 1.3.6.1.4.1.1332.1.1.5.3.10 msanPort OBJECT IDENTIFIER ::= { msanAdditionalConf 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.10.1 msanPortGlobal OBJECT IDENTIFIER ::= { msanPort 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.10.2 msanPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanPort 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.10.2.1 msanPortEntry OBJECT-TYPE SYNTAX MsanPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanPortTable 1 } MsanPortEntry ::= SEQUENCE { msanPortMNFlag INTEGER, msanPortMasterSlave INTEGER, msanPortNegCapAdvertisedBits BITS, msanPortSpeedDuplex INTEGER, msanPortStpP2PAutoState INTEGER, msanPortUsageType INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.10.2.1.1 msanPortMNFlag OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object determines whether to allow or not allow management access to a specific link. The factory default is enabled. " DEFVAL { enable } ::= { msanPortEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.10.2.1.6 msanPortMasterSlave OBJECT-TYPE SYNTAX INTEGER { none(1), master(2), slave(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object determines whether Gb port should be master or slave. Set to none when auto-negotiation and for non-Gb ports." DEFVAL { none } ::= { msanPortEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.10.2.1.7 msanPortNegCapAdvertisedBits OBJECT-TYPE SYNTAX BITS { bOther(0), b10baseT(1), b10baseTFD(2), b100baseT4(3), b100baseTX(4), b100baseTXFD(5), b100baseT2(6), b100baseT2FD(7), bFdxPause(8), bFdxAPause(9), bFdxSPause(10), bFdxBPause(11), b1000baseX(12), b1000baseXFD(13), b1000baseT(14), b1000baseTFD(15) } MAX-ACCESS read-write STATUS current DESCRIPTION "A value that uniquely identifies the set of capabilities advertised by the local auto-negotiation entity. Note that the local auto-negotiation entity may advertise some capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for capabilities that are listed above. Only b1000baseXFD(13) and b1000baseTFD(15) are currently supported." REFERENCE "[IEEE 802.3 Std], 30.6.1.1.6, aAutoNegAdvertisedTechnologyAbility; ifMauAutoNegCapAdvertisedBits (OID 1.3.6.1.2.1.26.5.1.1.11)" ::= { msanPortEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.10.2.1.8 msanPortSpeedDuplex OBJECT-TYPE SYNTAX INTEGER { speed10MbpsHD(10), speed10MbpsFD(11), speed100MbpsHD(15), speed100MbpsFD(16), speed100MbpsFDFiber(18), speed1000MbpsFDFiber(26), speed1000MbpsFD(30), speed10GbpsFDFiber(31) } MAX-ACCESS read-write STATUS current DESCRIPTION "Speed and duplex mode of the interface." ::= { msanPortEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.10.2.1.20 msanPortStpP2PAutoState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The field extends ISKRATEL-MSAN-BASICCONF-MIB.agentStpCstPortOperPointToPoint by the value." DEFVAL { enable } ::= { msanPortEntry 20 } -- 1.3.6.1.4.1.1332.1.1.5.3.10.2.1.21 msanPortUsageType OBJECT-TYPE SYNTAX INTEGER { uplink(1), downlink(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the type of an interface whether it is an uplink or downlink. " ::= { msanPortEntry 21 } -- 1.3.6.1.4.1.1332.1.1.5.3.11 msanPppoeIA OBJECT IDENTIFIER ::= { msanAdditionalConf 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.1 msanPppoeIAGlobal OBJECT IDENTIFIER ::= { msanPppoeIA 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.1.1 msanPppoeIAStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies if the PPPOE Intermadiate Agent Service is to be Enabled or Disabled." ::= { msanPppoeIAGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.1.2 msanPppoeIAVsaReplyMode OBJECT-TYPE SYNTAX INTEGER { keep(1), remove(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies PPPOE Intermadiate Agent keep/remove option 82 in replies." ::= { msanPppoeIAGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.1.3 msanPppoeIACircuitIdStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the disable/enable inserting Circuit ID suboption." ::= { msanPppoeIAGlobal 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.1.4 msanPppoeIARemoteIdStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the disable/enable inserting Remote ID suboption." ::= { msanPppoeIAGlobal 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.2 msanPppoeIAPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanPppoeIAPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanPppoeIA 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.2.1 msanPppoeIAPortEntry OBJECT-TYPE SYNTAX MsanPppoeIAPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanPppoeIAPortTable 1 } MsanPppoeIAPortEntry ::= SEQUENCE { msanPppoeIAPortStatus INTEGER, msanPppoeIAPortRemoteId OCTET STRING, msanPppoeIAPortCircuitType INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.11.2.1.1 msanPppoeIAPortStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2), enableClient(3), enableServer(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "State of PPPoE Intermadiate Agent on the port" ::= { msanPppoeIAPortEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.2.1.2 msanPppoeIAPortRemoteId OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Remote Id for the port." ::= { msanPppoeIAPortEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.2.1.3 msanPppoeIAPortCircuitType OBJECT-TYPE SYNTAX INTEGER { trusted(1), untrusted(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "PPPoE IA Circuit type per port." DEFVAL { untrusted } ::= { msanPppoeIAPortEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3 msanPppoeIaStatistics OBJECT IDENTIFIER ::= { msanPppoeIA 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3.1 msanPppoeIaStatPADI OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of PADI packets." ::= { msanPppoeIaStatistics 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3.2 msanPppoeIaStatPADR OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of PADR packets." ::= { msanPppoeIaStatistics 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3.3 msanPppoeIaStatPADO OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of PADO packets." ::= { msanPppoeIaStatistics 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3.4 msanPppoeIaStatPADS OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of PADS packets." ::= { msanPppoeIaStatistics 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3.5 msanPppoeIaStatPADT OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of PADT packets." ::= { msanPppoeIaStatistics 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3.6 msanPppoeIaStatUnsutableFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets with unsutable frame." ::= { msanPppoeIaStatistics 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3.7 msanPppoeIaStatUnknownFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets with unknown frame." ::= { msanPppoeIaStatistics 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3.8 msanPppoeIaStatInvalidFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets with invalid frame." ::= { msanPppoeIaStatistics 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3.9 msanPppoeIaPortStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanPppoeIaPortStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanPppoeIaStatistics 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3.9.1 msanPppoeIaPortStatisticsEntry OBJECT-TYPE SYNTAX MsanPppoeIaPortStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanPppoeIaPortStatisticsTable 1 } MsanPppoeIaPortStatisticsEntry ::= SEQUENCE { msanPppoeIaPortStatPADI Counter32, msanPppoeIaPortStatPADR Counter32, msanPppoeIaPortStatPADO Counter32, msanPppoeIaPortStatPADS Counter32, msanPppoeIaPortStatPADT Counter32, msanPppoeIaPortStatUnsutableFrames Counter32, msanPppoeIaPortStatUnknownFrames Counter32, msanPppoeIaPortStatInvalidFrames Counter32 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3.9.1.1 msanPppoeIaPortStatPADI OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of PADI packets on the port. " ::= { msanPppoeIaPortStatisticsEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3.9.1.2 msanPppoeIaPortStatPADR OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of PADR packets on the port. " ::= { msanPppoeIaPortStatisticsEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3.9.1.3 msanPppoeIaPortStatPADO OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of PADO packets on the port. " ::= { msanPppoeIaPortStatisticsEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3.9.1.4 msanPppoeIaPortStatPADS OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of PADS packets on the port. " ::= { msanPppoeIaPortStatisticsEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3.9.1.5 msanPppoeIaPortStatPADT OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of PADT packets on the port. " ::= { msanPppoeIaPortStatisticsEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3.9.1.6 msanPppoeIaPortStatUnsutableFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets with unsutable frame on the port. " ::= { msanPppoeIaPortStatisticsEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3.9.1.7 msanPppoeIaPortStatUnknownFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets with unknown frame on the port. " ::= { msanPppoeIaPortStatisticsEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.3.9.1.8 msanPppoeIaPortStatInvalidFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets with invalid frame on the port. " ::= { msanPppoeIaPortStatisticsEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.4 msanPppoeIaVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanPppoeIaVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanPppoeIA 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.11.4.1 msanPppoeIaVlanEntry OBJECT-TYPE SYNTAX MsanPppoeIaVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { dot1qVlanIndex } ::= { msanPppoeIaVlanTable 1 } MsanPppoeIaVlanEntry ::= SEQUENCE { msanPppoeIaVlanStatus INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.11.4.1.1 msanPppoeIaVlanStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "State of PPPoE Intermadiate Agent per VLAN." ::= { msanPppoeIaVlanEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.12 msanQoS OBJECT IDENTIFIER ::= { msanAdditionalConf 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.1 msanQosGlobal OBJECT IDENTIFIER ::= { msanQoS 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2 msanIpAclRuleTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanIpAclRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table extends aclTable/aclRuleTable." ::= { msanQoS 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1 msanIpAclRuleEntry OBJECT-TYPE SYNTAX MsanIpAclRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table extends aclTable/aclRuleTable." INDEX { msanIpAclIndex, msanIpAclRuleIndex } ::= { msanIpAclRuleTable 1 } MsanIpAclRuleEntry ::= SEQUENCE { msanIpAclIndex Integer32, msanIpAclRuleIndex Integer32, msanIpAclRuleAssignVlanId Integer32, msanIpAclRuleAssignCoSPriority Integer32, msanIpAclRuleEgressIntf Integer32, msanIpAclRuleAssignVlanId2 Integer32, msanIpAclRuleRemoveVlanId INTEGER, msanIpAclRuleIcmpType INTEGER, msanIpAclRuleDestMacAddr MacAddress, msanIpAclRuleDestMacMask MacAddress, msanIpAclRuleSrcMacAddr MacAddress, msanIpAclRuleSrcMacMask MacAddress, msanIpAclRuleCos INTEGER, msanIpAclRuleCos2 INTEGER, msanIpAclRuleVlanId Unsigned32, msanIpAclRuleVlanId2 Unsigned32, msanIpAclRuleCVlanId Integer32, msanIpAclRuleSVlanId Integer32, msanIpAclRuleAssignCVlanId Integer32, msanIpAclRuleAssignSVlanId Integer32, msanIpAclRuleRemoveSVlanId INTEGER, msanIpAclRuleVlanIdRangeStart Unsigned32, msanIpAclRuleVlanIdRangeEnd Unsigned32, msanIpAclRuleVlanId2RangeStart Unsigned32, msanIpAclRuleVlanId2RangeEnd Unsigned32, msanIpAclRuleSVlanIdRangeStart Unsigned32, msanIpAclRuleSVlanIdRangeEnd Unsigned32, msanIpAclRuleCVlanIdRangeStart Unsigned32, msanIpAclRuleCVlanIdRangeEnd Unsigned32, msanIpAclRuleSrcIpv6Address InetAddressIPv6, msanIpAclRuleSrcIpv6AddressMaskLen Integer32, msanIpAclRuleDestIpv6Address InetAddressIPv6, msanIpAclRuleDestIpv6AddressMaskLen Integer32 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.1 msanIpAclIndex OBJECT-TYPE SYNTAX Integer32 (1..199) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is aclIndex in aclTable" ::= { msanIpAclRuleEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.2 msanIpAclRuleIndex OBJECT-TYPE SYNTAX Integer32 (1..9) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of the IP ACL rule (aclRuleIndex in aclRuleTable)." ::= { msanIpAclRuleEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.3 msanIpAclRuleAssignVlanId OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "Assign VLAN Id." ::= { msanIpAclRuleEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.4 msanIpAclRuleAssignCoSPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Assign CoS priority" ::= { msanIpAclRuleEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.5 msanIpAclRuleEgressIntf OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Egress interface ID (ifIndex/ifTable)." ::= { msanIpAclRuleEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.6 msanIpAclRuleAssignVlanId2 OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "Assign Secondary VLAN ID -> add (if not exists) or change." ::= { msanIpAclRuleEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.7 msanIpAclRuleRemoveVlanId OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Remove VLAN Id (outer)." DEFVAL { disable } ::= { msanIpAclRuleEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.8 msanIpAclRuleIcmpType OBJECT-TYPE SYNTAX INTEGER { echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), routerAdvertisement(9), routerSolicitation(10), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply(18) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "ICMP message type used in the MAC ACL Classification. This parameter is used if aclRuleProtocol is set to icmp(1)." ::= { msanIpAclRuleEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.9 msanIpAclRuleDestMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The Destination MAC address used in the Advanced IP ACL Classification. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299" ::= { msanIpAclRuleEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.10 msanIpAclRuleDestMacMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The Destination MAC address mask used in the Advanced IP Classification. This mask value identifies the portion of the msanIpAclRuleDestMacAddr that is compared against a packet. A non-contiguous mask value is permitted. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299" ::= { msanIpAclRuleEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.11 msanIpAclRuleSrcMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The Source MAC address used in the Advanced IP ACL Classification. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299" ::= { msanIpAclRuleEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.12 msanIpAclRuleSrcMacMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The Source MAC address mask used in the Advanced IP Classification. This mask value identifies the portion of the msanIpAclRuleSrcMacAddr that is compared against a packet. A non-contiguous mask value is permitted. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299" ::= { msanIpAclRuleEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.13 msanIpAclRuleCos OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The Class of Service (COS) used in the Advanced IP Classification. This is the three-bit user priority field in the 802.1Q tag header of a tagged Ethernet frame. For frames containing a double VLAN tag, this field is located in the first/outer tag. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299 " ::= { msanIpAclRuleEntry 13 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.14 msanIpAclRuleCos2 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The Secondary Class of Service (COS) used in the Advanced IP Classification. This is the three-bit user priority field in the second 802.1Q tag header of a tagged Ethernet frame. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299 " ::= { msanIpAclRuleEntry 14 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.15 msanIpAclRuleVlanId OBJECT-TYPE SYNTAX Unsigned32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN ID value used in the Advanced IP Classification. The VLAN ID field is defined as the 12-bit VLAN identifier in the 802.1Q tag header of a tagged Ethernet frame. This is contained in the first/outer tag of a double VLAN tagged frame. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299 " ::= { msanIpAclRuleEntry 15 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.16 msanIpAclRuleVlanId2 OBJECT-TYPE SYNTAX Unsigned32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The Secondary VLAN ID value used in the Advanced IP Classification. The VLAN ID field is defined as the 12-bit VLAN identifier in the second 802.1Q tag header of a tagged Ethernet frame. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299 " ::= { msanIpAclRuleEntry 16 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.17 msanIpAclRuleCVlanId OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The C-customer VLAN ID value used in the Advanced IP Classification. The VLAN ID field is defined as the 12-bit VLAN identifier in the second 802.1Q tag header of a tagged Ethernet frame. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299" ::= { msanIpAclRuleEntry 17 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.18 msanIpAclRuleSVlanId OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The S-service VLAN ID value used in the Advanced IP Classification. The VLAN ID field is defined as the 12-bit VLAN identifier in the 802.1Q tag header of a tagged Ethernet frame. This is contained in the first/outer tag of a double VLAN tagged frame. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299" ::= { msanIpAclRuleEntry 18 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.19 msanIpAclRuleAssignCVlanId OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "Assign C VLAN ID -> add (if not exists) or change. Used in the Advanced IP Classification. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299" ::= { msanIpAclRuleEntry 19 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.20 msanIpAclRuleAssignSVlanId OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "Assign S VLAN ID -> add (if not exists) or change. Used in the Advanced IP Classification. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299" ::= { msanIpAclRuleEntry 20 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.21 msanIpAclRuleRemoveSVlanId OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Remove S-service VLAN ID. Used in the Advanced IP Classification. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299" ::= { msanIpAclRuleEntry 21 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.22 msanIpAclRuleVlanIdRangeStart OBJECT-TYPE SYNTAX Unsigned32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN ID range start value used in the Advanced IP Classification. Setting this value greater than the current msanIpAclRuleVlanIdRangeEnd changes the VLAN ID range end to the same value as the range start. The VLAN ID field is defined as the 12-bit VLAN identifier in the 802.1Q tag header of a tagged Ethernet frame. This is contained in the first/outer tag of a double VLAN tagged frame. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299" ::= { msanIpAclRuleEntry 22 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.23 msanIpAclRuleVlanIdRangeEnd OBJECT-TYPE SYNTAX Unsigned32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN ID range end value used in the Advanced IP Classification. Setting this value less than the current msanIpAclRuleVlanIdRangeStart changes the VLAN ID range start to the same value as the range end. The VLAN ID field is defined as the 12-bit VLAN identifier in the 802.1Q tag header of a tagged Ethernet frame. This is contained in the first/outer tag of a double VLAN tagged frame. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299" ::= { msanIpAclRuleEntry 23 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.24 msanIpAclRuleVlanId2RangeStart OBJECT-TYPE SYNTAX Unsigned32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The Secondary VLAN ID range start value used in the Advanced IP Classification. Setting this value greater than the current msanIpAclRuleVlanId2RangeEnd changes the VLAN ID range end to the same value as the range start. The VLAN ID field is defined as the 12-bit VLAN identifier in the second 802.1Q tag header of a tagged Ethernet frame. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299" ::= { msanIpAclRuleEntry 24 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.25 msanIpAclRuleVlanId2RangeEnd OBJECT-TYPE SYNTAX Unsigned32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The Secondary VLAN ID range end value used in the Advanced IP Classification. Setting this value less than the current msanIpAclRuleVlanId2RangeStart changes the VLAN ID range start to the same value as the range end. The VLAN ID field is defined as the 12-bit VLAN identifier in the second 802.1Q tag header of a tagged Ethernet frame. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299" ::= { msanIpAclRuleEntry 25 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.26 msanIpAclRuleSVlanIdRangeStart OBJECT-TYPE SYNTAX Unsigned32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The S-service VLAN ID range start value used in the Advanced IP Classification. Setting this value greater than the current msanIpAclRuleSVlanIdRangeEnd changes the VLAN ID range end to the same value as the range start. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299" ::= { msanIpAclRuleEntry 26 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.27 msanIpAclRuleSVlanIdRangeEnd OBJECT-TYPE SYNTAX Unsigned32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The S-service VLAN ID range end value used in the Advanced IP Classification. Setting this value less than the current msanIpAclRuleSVlanIdRangeStart changes the VLAN ID range start to the same value as the range end. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299" ::= { msanIpAclRuleEntry 27 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.28 msanIpAclRuleCVlanIdRangeStart OBJECT-TYPE SYNTAX Unsigned32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The C-customer VLAN ID range start value used in the Advanced IP Classification. Setting this value greater than the current msanIpAclRuleCVlanIdRangeEnd changes the VLAN ID range end to the same value as the range start. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299" ::= { msanIpAclRuleEntry 28 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.29 msanIpAclRuleCVlanIdRangeEnd OBJECT-TYPE SYNTAX Unsigned32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The C-customer VLAN ID range end value used in the Advanced IP Classification. Setting this value less than the current msanIpAclRuleCVlanIdRangeStart changes the VLAN ID range start to the same value as the range end. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299" ::= { msanIpAclRuleEntry 29 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.31 msanIpAclRuleSrcIpv6Address OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-write STATUS current DESCRIPTION "The Source IPv6 Address used in the ACL Classification. " ::= { msanIpAclRuleEntry 31 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.32 msanIpAclRuleSrcIpv6AddressMaskLen OBJECT-TYPE SYNTAX Integer32 (0..128) MAX-ACCESS read-write STATUS current DESCRIPTION "The length of the prefix (in bits) associated with the IPv6 source address of this entry (msanIpAclRuleSrcIpv6Address). Value 0 indicates that parameter has not been defined." DEFVAL { 0 } ::= { msanIpAclRuleEntry 32 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.33 msanIpAclRuleDestIpv6Address OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-write STATUS current DESCRIPTION "The Destination IPv6 Address used in the ACL Classification. " ::= { msanIpAclRuleEntry 33 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.2.1.34 msanIpAclRuleDestIpv6AddressMaskLen OBJECT-TYPE SYNTAX Integer32 (0..128) MAX-ACCESS read-write STATUS current DESCRIPTION "The length of the prefix (in bits) associated with the IPv6 destination address of this entry (msanIpAclRuleDestIpv6Address). Value 0 indicates that parameter has not been defined." DEFVAL { 0 } ::= { msanIpAclRuleEntry 34 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.3 msanMacAclRuleTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMacAclRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table extends aclMacTable/aclMacRuleTable." ::= { msanQoS 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.3.1 msanMacAclRuleEntry OBJECT-TYPE SYNTAX MsanMacAclRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table extends aclMacTable/aclMacRuleTable." INDEX { msanMacAclIndex, msanMacAclRuleIndex } ::= { msanMacAclRuleTable 1 } MsanMacAclRuleEntry ::= SEQUENCE { msanMacAclIndex Integer32, msanMacAclRuleIndex Integer32, msanMacAclRuleEgressIntf Integer32, msanMacAclRuleAssignVlanId Integer32, msanMacAclRuleAssignCoSPriority Integer32, msanMacAclRuleAssignVlanId2 Integer32, msanMacAclRuleRemoveVlanId INTEGER, msanMacAclRuleCVlanId Integer32, msanMacAclRuleSVlanId Integer32, msanMacAclRuleAssignCVlanId Integer32, msanMacAclRuleAssignSVlanId Integer32, msanMacAclRuleRemoveSVlanId INTEGER, msanMacAclRuleSVlanIdRangeStart Unsigned32, msanMacAclRuleSVlanIdRangeEnd Unsigned32, msanMacAclRuleCVlanIdRangeStart Unsigned32, msanMacAclRuleCVlanIdRangeEnd Unsigned32 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.3.1.1 msanMacAclIndex OBJECT-TYPE SYNTAX Integer32 (1..1000) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is aclMacIndex in aclMacTable" ::= { msanMacAclRuleEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.3.1.2 msanMacAclRuleIndex OBJECT-TYPE SYNTAX Integer32 (1..1000) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of the MAC ACL rule (aclMACRuleIndex in aclMACRuleTable)." ::= { msanMacAclRuleEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.3.1.3 msanMacAclRuleEgressIntf OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Egress Interface ID (ifIndex/ifTable)." ::= { msanMacAclRuleEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.3.1.4 msanMacAclRuleAssignVlanId OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "Assign VLAN Id." ::= { msanMacAclRuleEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.3.1.5 msanMacAclRuleAssignCoSPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Assign CoS priority" ::= { msanMacAclRuleEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.3.1.6 msanMacAclRuleAssignVlanId2 OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "Assign Secondary VLAN ID -> add (if not exists) or change." ::= { msanMacAclRuleEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.3.1.7 msanMacAclRuleRemoveVlanId OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Remove outer VLAN Id (outer)." DEFVAL { disable } ::= { msanMacAclRuleEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.3.1.8 msanMacAclRuleCVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "C-customer Vlan ID" ::= { msanMacAclRuleEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.3.1.9 msanMacAclRuleSVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "S-service Vlan ID" ::= { msanMacAclRuleEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.3.1.10 msanMacAclRuleAssignCVlanId OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "Assign C-customer VLAN ID -> add (if not exists) or change." ::= { msanMacAclRuleEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.3.1.11 msanMacAclRuleAssignSVlanId OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "Assign S-service VLAN ID -> add (if not exists) or change." ::= { msanMacAclRuleEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.3.1.12 msanMacAclRuleRemoveSVlanId OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Remove S-service VLAN ID." ::= { msanMacAclRuleEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.3.1.13 msanMacAclRuleSVlanIdRangeStart OBJECT-TYPE SYNTAX Unsigned32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The S-service VLAN ID range start value. Setting this value greater than the current msanMacAclRuleSVlanIdRangeEnd changes the VLAN ID range end to the same value as the range start. " ::= { msanMacAclRuleEntry 13 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.3.1.14 msanMacAclRuleSVlanIdRangeEnd OBJECT-TYPE SYNTAX Unsigned32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The S-service VLAN ID range end value. Setting this value less than the current msanMacAclRuleSVlanIdRangeStart changes the VLAN ID range start to the same value as the range end." ::= { msanMacAclRuleEntry 14 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.3.1.15 msanMacAclRuleCVlanIdRangeStart OBJECT-TYPE SYNTAX Unsigned32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The C-customer VLAN ID range start value. Setting this value greater than the current msanMacAclRuleCVlanIdRangeEnd changes the VLAN ID range end to the same value as the range start. " ::= { msanMacAclRuleEntry 15 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.3.1.16 msanMacAclRuleCVlanIdRangeEnd OBJECT-TYPE SYNTAX Unsigned32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The C-customer VLAN ID range end value. Setting this value less than the current msanMacAclRuleCVlanIdRangeStart changes the VLAN ID range start to the same value as the range end." ::= { msanMacAclRuleEntry 16 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.4 msanCosQueueControlTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanCosQueueControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanQoS 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.4.1 msanCosQueueControlEntry OBJECT-TYPE SYNTAX MsanCosQueueControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanCosQueueControlTable 1 } MsanCosQueueControlEntry ::= SEQUENCE { msanCosQueueControlIntfBurstSize Integer32, msanCosQueueIntfShapingRate Unsigned32 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.4.1.1 msanCosQueueControlIntfBurstSize OBJECT-TYPE SYNTAX Integer32 UNITS "kilobyte" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum number of uncommitted bytes that the switch will try to send into the network. It is the number of bytes that are sent at a rate, higher than committed and that the next device in the network must be able to buffer without notifying a congestion. Default value is 0. Valid values are 16, 20, 28, 40, 76, 140, 268 and 524 kilobytes. Configuring shaping rate without burst size will take the maximum possible value of burst, which is 524 KB. " ::= { msanCosQueueControlEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.4.1.2 msanCosQueueIntfShapingRate OBJECT-TYPE SYNTAX Unsigned32 (0..10000000) UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the maximum bandwidth allowed, typically used to shape the outbound transmission rate. This value is controlled independently of any per-queue maximum bandwidth configuration. It is effectively a second-level shaping mechanism. Default value is 0. Valid Range is 0 to 10000000 kbps. The value 0 means maximum is unlimited." ::= { msanCosQueueControlEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.5 msanCosQueueTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanCosQueueEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of class-of-service queue configuration parameters for the specified interface. This is extension of the table agentCosQueueTable. " REFERENCE "agentCosQueueTable - 1.3.6.1.4.1.6132.1.1.3.3.2.4" ::= { msanQoS 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.5.1 msanCosQueueEntry OBJECT-TYPE SYNTAX MsanCosQueueEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry describes a single class-of-service (COS) queue for a given Interface Index. The number of configurable COS queues for an interface vary based on device capabilities. All objects defined for this table entry contain a default value corresponding to a typical, non-preferential treatment of packets traversing the interface's COS queues." REFERENCE "agentCosQueueTable - 1.3.6.1.4.1.6132.1.1.3.3.2.4" INDEX { ifIndex, msanCosQueueIndex } ::= { msanCosQueueTable 1 } MsanCosQueueEntry ::= SEQUENCE { msanCosQueueIndex Integer32, msanCosQueueWeight INTEGER, msanCosQueueLength INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.12.5.1.1 msanCosQueueIndex OBJECT-TYPE SYNTAX Integer32 (0..1000) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The COS queue index, numbered 0 to (n-1), where n is the total number of configurable interface queues for the device as indicated by agentCosQueueNumQueuesPerPort. In general, a higher numbered queue index is used to support higher priority traffic, although actual operation may be altered via configuration through this table." ::= { msanCosQueueEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.5.1.2 msanCosQueueWeight OBJECT-TYPE SYNTAX INTEGER (0..32) MAX-ACCESS read-write STATUS current DESCRIPTION "Weight of the queue being used in egress scheduling algorithm." ::= { msanCosQueueEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.5.1.3 msanCosQueueLength OBJECT-TYPE SYNTAX INTEGER (2..156) MAX-ACCESS read-write STATUS current DESCRIPTION "Length of the queue in kB. " DEFVAL { 40 } ::= { msanCosQueueEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.6 msanCosMapIntfTrustTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanCosMapIntfTrustEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanQoS 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.6.1 msanCosMapIntfTrustEntry OBJECT-TYPE SYNTAX MsanCosMapIntfTrustEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanCosMapIntfTrustTable 1 } MsanCosMapIntfTrustEntry ::= SEQUENCE { msanCosMapIntfTrustMode INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.12.6.1.1 msanCosMapIntfTrustMode OBJECT-TYPE SYNTAX INTEGER { untrusted(1), trustDot1p(2), trustIpPrecedence(3), trustIpDscp(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is copy of LVL7 parameter agentCosMapIntfTrustMode, except that index 0 is not supported. The class of service trust mode of an interface. When set to a trusted mode, the appropriate COS mapping table is used as follows: trustDot1p(2) : dot1dTrafficClassTable trustIpPrecedence(3): agentCosMapIpPrecTable trustIpDscp(4): agentCosMapIpDscpTable For an untrusted(1) interface, packets are handled in accordance with the dot1dPortDefaultUserPriority value of the ingress port. " ::= { msanCosMapIntfTrustEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7 msanQosProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanQosProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanQoS 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1 msanQosProfileEntry OBJECT-TYPE SYNTAX MsanQosProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanQosProfileName } ::= { msanQosProfileTable 1 } MsanQosProfileEntry ::= SEQUENCE { msanQosProfileName OCTET STRING, msanQosProfileMatchInAny INTEGER, msanQosProfileMatchInMacDestAddr MacAddress, msanQosProfileMatchInMacDestMask MacAddress, msanQosProfileMatchInMacSrcAddr MacAddress, msanQosProfileMatchInMacSrcMask MacAddress, msanQosProfileMatchInCos Integer32, msanQosProfileMatchInCos2 Integer32, msanQosProfileMatchInVlanId Integer32, msanQosProfileMatchInVlanId2 Integer32, msanQosProfileMatchInEthertype Integer32, msanQosProfileMatchInIpProtocol Integer32, msanQosProfileMatchInIpSrcAddr IpAddress, msanQosProfileMatchInIpSrcMask IpAddress, msanQosProfileMatchInIpDestAddr IpAddress, msanQosProfileMatchInIpDestMask IpAddress, msanQosProfileMatchInIpDscp Integer32, msanQosProfileMatchInIpPrecedence Integer32, msanQosProfileMatchInIpTosBits OCTET STRING, msanQosProfileMatchInIpTosMask OCTET STRING, msanQosProfileMatchInL4SrcPort Integer32, msanQosProfileMatchInL4DestPort Integer32, msanQosProfileMatchOutAny INTEGER, msanQosProfileMatchOutMacDestAddr MacAddress, msanQosProfileMatchOutMacDestMask MacAddress, msanQosProfileMatchOutMacSrcAddr MacAddress, msanQosProfileMatchOutMacSrcMask MacAddress, msanQosProfileMatchOutCos Integer32, msanQosProfileMatchOutCos2 Integer32, msanQosProfileMatchOutVlanId Integer32, msanQosProfileMatchOutVlanId2 Integer32, msanQosProfileMatchOutEthertype Integer32, msanQosProfileMatchOutIpProtocol Integer32, msanQosProfileMatchOutIpSrcAddr IpAddress, msanQosProfileMatchOutIpSrcMask IpAddress, msanQosProfileMatchOutIpDestAddr IpAddress, msanQosProfileMatchOutIpDestMask IpAddress, msanQosProfileMatchOutIpDscp Integer32, msanQosProfileMatchOutIpPrecedence Integer32, msanQosProfileMatchOutIpTosBits OCTET STRING, msanQosProfileMatchOutIpTosMask OCTET STRING, msanQosProfileMatchOutL4SrcPort Integer32, msanQosProfileMatchOutL4DestPort Integer32, msanQosProfileInCdr Integer32, msanQosProfileInPdr Integer32, msanQosProfileOutCdr Integer32, msanQosProfileOutPdr Integer32, msanQosProfileInTrustMode INTEGER, msanQosProfileInMarkCos INTEGER, msanQosProfileInMarkDscp INTEGER, msanQosProfileRowStatus RowStatus, msanQosProfilePriority INTEGER, msanQosProfileInCdrBurstSize Integer32, msanQosProfileInPdrBurstSize Integer32, msanQosProfileOutCdrBurstSize Integer32, msanQosProfileOutPdrBurstSize Integer32, msanQosProfileMatchInSrcIpv6Address InetAddressIPv6, msanQosProfileMatchInSrcIpv6AddressMaskLen Integer32, msanQosProfileMatchInDestIpv6Address InetAddressIPv6, msanQosProfileMatchInDestIpv6AddressMaskLen Integer32, msanQosProfileMatchOutSrcIpv6Address InetAddressIPv6, msanQosProfileMatchOutSrcIpv6AddressMaskLen Integer32, msanQosProfileMatchOutDestIpv6Address InetAddressIPv6, msanQosProfileMatchOutDestIpv6AddressMaskLen Integer32 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.1 msanQosProfileName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "QoS profile name." ::= { msanQosProfileEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.2 msanQosProfileMatchInAny OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Match every incoming packet frame." DEFVAL { disable } ::= { msanQosProfileEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.3 msanQosProfileMatchInMacDestAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified destination MAC address. Empty string indicates that parameter has not been defined" DEFVAL { ''b } ::= { msanQosProfileEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.4 msanQosProfileMatchInMacDestMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanQosProfileMatchInMacDestAddr that is compared with input packet. Empty string indicates that parameter has not been defined" DEFVAL { ''b } ::= { msanQosProfileEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.5 msanQosProfileMatchInMacSrcAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified source MAC address. Empty string indicates that parameter has not been defined" DEFVAL { ''b } ::= { msanQosProfileEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.6 msanQosProfileMatchInMacSrcMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanQosProfileMatchInMacSrcAddr that is compared with input packet. Empty string indicates that parameter has not been defined" DEFVAL { ''b } ::= { msanQosProfileEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.7 msanQosProfileMatchInCos OBJECT-TYPE SYNTAX Integer32 (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified CoS value (0-7). A value of -1 indicates that parameter has not been defined" DEFVAL { -1 } ::= { msanQosProfileEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.8 msanQosProfileMatchInCos2 OBJECT-TYPE SYNTAX Integer32 (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified secondary (C-TAG) CoS value (0-7). A value of -1 indicates that parameter has not been defined" DEFVAL { -1 } ::= { msanQosProfileEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.9 msanQosProfileMatchInVlanId OBJECT-TYPE SYNTAX Integer32 (-1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified VLAN ID value (1-4094). A value of -1 indicates that parameter has not been defined" DEFVAL { -1 } ::= { msanQosProfileEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.10 msanQosProfileMatchInVlanId2 OBJECT-TYPE SYNTAX Integer32 (-1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified secondary (C-TAG) VLAN ID value (1-4094). A value of -1 indicates that parameter has not been defined" DEFVAL { -1 } ::= { msanQosProfileEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.11 msanQosProfileMatchInEthertype OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified EtherType value. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanQosProfileEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.12 msanQosProfileMatchInIpProtocol OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified IP protocol value. A value of -1 indicates that parameter has not been defined. Some of standard protocol values: icmp - 1 igmp - 2 ip - 4 (ip in ip encapsulation) tcp - 6 udp - 17" DEFVAL { -1 } ::= { msanQosProfileEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.13 msanQosProfileMatchInIpSrcAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified source IP address. Empty string indicates that parameter has not been defined." DEFVAL { ''h } ::= { msanQosProfileEntry 13 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.14 msanQosProfileMatchInIpSrcMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanQosProfileMatchInIpSrcAddr that is compared with input packet. Empty string indicates that parameter has not been defined" DEFVAL { ''h } ::= { msanQosProfileEntry 14 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.15 msanQosProfileMatchInIpDestAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified destination IP address. Empty string indicates that parameter has not been defined." DEFVAL { ''h } ::= { msanQosProfileEntry 15 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.16 msanQosProfileMatchInIpDestMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanQosProfileMatchInIpDestAddr that is compared with input packet. Empty string indicates that parameter has not been defined" DEFVAL { ''h } ::= { msanQosProfileEntry 16 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.17 msanQosProfileMatchInIpDscp OBJECT-TYPE SYNTAX Integer32 (-1..63) MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified IP DSCP value. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanQosProfileEntry 17 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.18 msanQosProfileMatchInIpPrecedence OBJECT-TYPE SYNTAX Integer32 (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified IP precedence (part of TOS field) value. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanQosProfileEntry 18 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.19 msanQosProfileMatchInIpTosBits OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..1)) MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified IP TOS bits value. Empty string indicates that parameter has not been defined." DEFVAL { ''b } ::= { msanQosProfileEntry 19 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.20 msanQosProfileMatchInIpTosMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..1)) MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanQosProfileMatchInIpTosBits that is compared against a packet. Empty string indicates that parameter has not been defined." DEFVAL { ''b } ::= { msanQosProfileEntry 20 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.21 msanQosProfileMatchInL4SrcPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified source TCP/UDP port number. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanQosProfileEntry 21 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.22 msanQosProfileMatchInL4DestPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified destination TCP/UDP port number in downstream direction. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanQosProfileEntry 22 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.23 msanQosProfileMatchOutAny OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Match every outgoing packet frame in upstream direction." DEFVAL { disable } ::= { msanQosProfileEntry 23 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.24 msanQosProfileMatchOutMacDestAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match outgoing packet frame with specified destination MAC address. Empty string indicates that parameter has not been defined" DEFVAL { ''b } ::= { msanQosProfileEntry 24 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.25 msanQosProfileMatchOutMacDestMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanQosProfileMatchOutMacDestAddr that is compared with output packet. Empty string indicates that parameter has not been defined" DEFVAL { ''b } ::= { msanQosProfileEntry 25 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.26 msanQosProfileMatchOutMacSrcAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match outgoing packet frame with specified source MAC address. Empty string indicates that parameter has not been defined" DEFVAL { ''b } ::= { msanQosProfileEntry 26 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.27 msanQosProfileMatchOutMacSrcMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanQosProfileMatchOutMacSrcAddr that is compared with output packet. Empty string indicates that parameter has not been defined" DEFVAL { ''b } ::= { msanQosProfileEntry 27 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.28 msanQosProfileMatchOutCos OBJECT-TYPE SYNTAX Integer32 (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Match outgoing packet frame with specified CoS value (0-7). A value of -1 indicates that parameter has not been defined" DEFVAL { -1 } ::= { msanQosProfileEntry 28 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.29 msanQosProfileMatchOutCos2 OBJECT-TYPE SYNTAX Integer32 (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Match outgoing packet frame with specified secondary (C-TAG) CoS value (0-7). A value of -1 indicates that parameter has not been defined" DEFVAL { -1 } ::= { msanQosProfileEntry 29 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.30 msanQosProfileMatchOutVlanId OBJECT-TYPE SYNTAX Integer32 (-1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Match outgoing packet frame with specified VLAN ID value (1-4094). A value of -1 indicates that parameter has not been defined" DEFVAL { -1 } ::= { msanQosProfileEntry 30 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.31 msanQosProfileMatchOutVlanId2 OBJECT-TYPE SYNTAX Integer32 (-1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Match outgoing packet frame with specified secondary (C-TAG) VLAN ID value (1-4094). A value of -1 indicates that parameter has not been defined" DEFVAL { -1 } ::= { msanQosProfileEntry 31 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.32 msanQosProfileMatchOutEthertype OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Match outgoing packet frame with specified EtherType value. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanQosProfileEntry 32 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.33 msanQosProfileMatchOutIpProtocol OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Match outgoing packet frame with specified IP protocol value in upstream direction. A value of -1 indicates that parameter has not been defined. Some of standard protocol values: icmp - 1 igmp - 2 ip - 4 (ip in ip encapsulation) tcp - 6 udp - 17" DEFVAL { -1 } ::= { msanQosProfileEntry 33 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.34 msanQosProfileMatchOutIpSrcAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match outgoing packet frame with specified source IP address. Empty string indicates that parameter has not been defined." DEFVAL { ''h } ::= { msanQosProfileEntry 34 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.35 msanQosProfileMatchOutIpSrcMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanQosProfileMatchOutIpSrcAddr that is compared with output packet. Empty string indicates that parameter has not been defined" DEFVAL { ''h } ::= { msanQosProfileEntry 35 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.36 msanQosProfileMatchOutIpDestAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match outgoing packet frame with specified destination IP address. Empty string indicates that parameter has not been defined." DEFVAL { ''h } ::= { msanQosProfileEntry 36 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.37 msanQosProfileMatchOutIpDestMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanQosProfileMatchOutIpDestAddr that is compared with output packet. Empty string indicates that parameter has not been defined" DEFVAL { ''h } ::= { msanQosProfileEntry 37 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.38 msanQosProfileMatchOutIpDscp OBJECT-TYPE SYNTAX Integer32 (-1..63) MAX-ACCESS read-write STATUS current DESCRIPTION "Match outgoing packet frame with specified IP DSCP value. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanQosProfileEntry 38 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.39 msanQosProfileMatchOutIpPrecedence OBJECT-TYPE SYNTAX Integer32 (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Match outgoing packet frame with specified IP precedence (part of TOS field) value. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanQosProfileEntry 39 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.40 msanQosProfileMatchOutIpTosBits OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..1)) MAX-ACCESS read-write STATUS current DESCRIPTION "Match outgoing packet frame with specified IP TOS bits value. Empty string indicates that parameter has not been defined." DEFVAL { ''b } ::= { msanQosProfileEntry 40 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.41 msanQosProfileMatchOutIpTosMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..1)) MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanQosProfileMatchOutIpTosBits that is compared with output packet. Empty string indicates that parameter has not been defined" DEFVAL { ''b } ::= { msanQosProfileEntry 41 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.42 msanQosProfileMatchOutL4SrcPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Match outgoing packet frame with specified source TCP/UDP port number in upstream direction. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanQosProfileEntry 42 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.43 msanQosProfileMatchOutL4DestPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Match outgoing packet frame with specified destination TCP/UDP port number. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanQosProfileEntry 43 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.44 msanQosProfileInCdr OBJECT-TYPE SYNTAX Integer32 (-1..1000000) UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Incoming committed data rate (E-CDR) in kbps (0 – 1000000). A value of -1 indicates that parameter has not been defined." DEFVAL { 0 } ::= { msanQosProfileEntry 44 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.45 msanQosProfileInPdr OBJECT-TYPE SYNTAX Integer32 (-1..1000000) UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Incoming peak data rate (E-PDR) in kbps (0 – 1000000). A value of -1 indicates that parameter has not been defined." DEFVAL { 0 } ::= { msanQosProfileEntry 45 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.46 msanQosProfileOutCdr OBJECT-TYPE SYNTAX Integer32 (-1..1000000) UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Outgoing committed data rate (E-CDR) in kbps (0 – 1000000). A value of -1 indicates that parameter has not been defined." DEFVAL { 0 } ::= { msanQosProfileEntry 46 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.47 msanQosProfileOutPdr OBJECT-TYPE SYNTAX Integer32 (-1..1000000) UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Outgoing peak data rate (E-PDR) in kbps (0 – 1000000). A value of -1 indicates that parameter has not been defined." DEFVAL { 0 } ::= { msanQosProfileEntry 47 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.48 msanQosProfileInTrustMode OBJECT-TYPE SYNTAX INTEGER { untrusted(1), trustCos(2), trustDscp(3), untrustMarkCos(4), untrustMarkDscp(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Trust mode for incoming packets which correspond to this profile. Default value is untrusted(1). Value untrustMarkCos(4) can be set if parameter msanQosProfileInMarkCos value is grater than -1. Value untrustMarkCos(5) can be set if parameter msanQosProfileInMarkDscp value is grater than -1." DEFVAL { untrusted } ::= { msanQosProfileEntry 48 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.49 msanQosProfileInMarkCos OBJECT-TYPE SYNTAX INTEGER (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Mark incoming packets with specified CoS value (0-7). A value of -1 indicates that parameter has not been defined" DEFVAL { -1 } ::= { msanQosProfileEntry 49 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.50 msanQosProfileInMarkDscp OBJECT-TYPE SYNTAX INTEGER (-1..63) MAX-ACCESS read-write STATUS current DESCRIPTION "Mark incoming packets with specified IP DSCP value. A value of -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanQosProfileEntry 50 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.51 msanQosProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). Value active(1) will activate and value destroy(6) will remove this entry. Other values are currently not supported. " ::= { msanQosProfileEntry 51 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.52 msanQosProfilePriority OBJECT-TYPE SYNTAX INTEGER { normal(1), high(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Priority of QoS profile. On interface can be linked only one QoS profile with high(2) prority (msanQoSIntProfileTable)" DEFVAL { normal } ::= { msanQosProfileEntry 52 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.53 msanQosProfileInCdrBurstSize OBJECT-TYPE SYNTAX Integer32 UNITS "kB" MAX-ACCESS read-write STATUS current DESCRIPTION "Incoming committed data rate burst size in kB (0 – 16384). When parameter is set to 0 (default), it's automatically updated to default burst size in according with current msanQoSProfileInCdr value. " ::= { msanQosProfileEntry 53 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.54 msanQosProfileInPdrBurstSize OBJECT-TYPE SYNTAX Integer32 UNITS "kB" MAX-ACCESS read-write STATUS current DESCRIPTION "Incoming peak data rate burst size in kB (0 – 16384). When parameter is set to 0 (default), it's automatically updated to default burst size in according with current msanQoSProfileInPdr value. " ::= { msanQosProfileEntry 54 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.55 msanQosProfileOutCdrBurstSize OBJECT-TYPE SYNTAX Integer32 UNITS "kB" MAX-ACCESS read-write STATUS current DESCRIPTION "Outgoing committed data rate burst size in kB (0 – 16384). When parameter is set to 0 (default), it's automatically updated to default burst size in according with current msanQoSProfileOutCdr value. " ::= { msanQosProfileEntry 55 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.56 msanQosProfileOutPdrBurstSize OBJECT-TYPE SYNTAX Integer32 UNITS "kB" MAX-ACCESS read-write STATUS current DESCRIPTION "Outgoing peak data rate burst size in kB (0 – 16384). When parameter is set to 0 (default), it's automatically updated to default burst size in according with current msanQoSProfileOutCdr value. " DEFVAL { 64 } ::= { msanQosProfileEntry 56 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.58 msanQosProfileMatchInSrcIpv6Address OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified source IPv6 address. Empty string indicates that parameter has not been defined." ::= { msanQosProfileEntry 58 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.59 msanQosProfileMatchInSrcIpv6AddressMaskLen OBJECT-TYPE SYNTAX Integer32 (0..128) MAX-ACCESS read-write STATUS current DESCRIPTION "The length of the prefix (in bits) associated with the incoming IPv6 source address of this entry (msanQosProfileMatchInSrcIpv6Address). Value 0 indicates that parameter has not been defined." DEFVAL { 0 } ::= { msanQosProfileEntry 59 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.60 msanQosProfileMatchInDestIpv6Address OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified destination IPv6 address. Empty string indicates that parameter has not been defined." ::= { msanQosProfileEntry 60 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.61 msanQosProfileMatchInDestIpv6AddressMaskLen OBJECT-TYPE SYNTAX Integer32 (0..128) MAX-ACCESS read-write STATUS current DESCRIPTION "The length of the prefix (in bits) associated with the incoming IPv6 destination address of this entry (msanQosProfileMatchInDestIpv6Address). Value 0 indicates that parameter has not been defined." DEFVAL { 0 } ::= { msanQosProfileEntry 61 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.63 msanQosProfileMatchOutSrcIpv6Address OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-write STATUS current DESCRIPTION "Match outgoing packet frame with specified source IPv6 address. Empty string indicates that parameter has not been defined." ::= { msanQosProfileEntry 63 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.64 msanQosProfileMatchOutSrcIpv6AddressMaskLen OBJECT-TYPE SYNTAX Integer32 (0..128) MAX-ACCESS read-write STATUS current DESCRIPTION "The length of the prefix (in bits) associated with the outcoming IPv6 source address of this entry (msanQosProfileMatchOutSrcIpv6Address). Value 0 indicates that parameter has not been defined." DEFVAL { 0 } ::= { msanQosProfileEntry 64 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.65 msanQosProfileMatchOutDestIpv6Address OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-write STATUS current DESCRIPTION "Match outcoming packet frame with specified destination IPv6 address. Empty string indicates that parameter has not been defined." ::= { msanQosProfileEntry 65 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.7.1.66 msanQosProfileMatchOutDestIpv6AddressMaskLen OBJECT-TYPE SYNTAX Integer32 (0..128) MAX-ACCESS read-write STATUS current DESCRIPTION "The length of the prefix (in bits) associated with the outcoming IPv6 destination address of this entry (msanQosProfileMatchOutDestIpv6Address). Value 0 indicates that parameter has not been defined." DEFVAL { 0 } ::= { msanQosProfileEntry 66 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.8 msanQosIntfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanQosIntfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table connects selected QoS profiles (msanQoSProfileName) to specified interfaces (ifIndex)." ::= { msanQoS 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.8.1 msanQosIntfProfileEntry OBJECT-TYPE SYNTAX MsanQosIntfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex, msanQosProfileName } ::= { msanQosIntfProfileTable 1 } MsanQosIntfProfileEntry ::= SEQUENCE { msanQosIntfProfileAtmVpi Integer32, msanQosIntfProfileAtmVci Integer32, msanQosIntfProfileRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.12.8.1.1 msanQosIntfProfileAtmVpi OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "ATM Virtual path identifier of the ADSL interface. Value -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanQosIntfProfileEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.8.1.2 msanQosIntfProfileAtmVci OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "ATM Virtual channel identifier of the ADSL interface. Value -1 indicates that parameter has not been defined." DEFVAL { -1 } ::= { msanQosIntfProfileEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.8.1.3 msanQosIntfProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deactivation use notInService(2). For row deletion use destroy(6). Other values are currently not supported. On interface can be linked only one QoS profile with high(2) prority (msanQosProfilePriority)" ::= { msanQosIntfProfileEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.9 msanQosStatistics OBJECT IDENTIFIER ::= { msanQoS 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.9.1 msanQosPortStatTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanQosPortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanQosStatistics 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.9.1.1 msanQosPortStatEntry OBJECT-TYPE SYNTAX MsanQosPortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanQosPortStatTable 1 } MsanQosPortStatEntry ::= SEQUENCE { msanQosPortStatInDroppedFrames Counter32, msanQosPortStatOutDroppedFrames Counter32 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.9.1.1.1 msanQosPortStatInDroppedFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of dropped frames per port in incoming direction." ::= { msanQosPortStatEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.9.1.1.2 msanQosPortStatOutDroppedFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of dropped frames per port in outgoing direction." ::= { msanQosPortStatEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.9.2 msanQosPortProfileStatTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanQosPortProfileStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanQosStatistics 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.9.2.1 msanQosPortProfileStatEntry OBJECT-TYPE SYNTAX MsanQosPortProfileStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex, msanQosProfileName } ::= { msanQosPortProfileStatTable 1 } MsanQosPortProfileStatEntry ::= SEQUENCE { msanQosPortProfileStatQueueCurrent Integer32, msanQosPortProfileStatQueueAverage Integer32, msanQosPortProfileStatQueueMax Integer32 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.9.2.1.1 msanQosPortProfileStatQueueCurrent OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current queue occupation per profile per port (in number of packets) ." ::= { msanQosPortProfileStatEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.9.2.1.2 msanQosPortProfileStatQueueAverage OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Average queue occupation per profile per port (in number of packets) ." ::= { msanQosPortProfileStatEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.9.2.1.3 msanQosPortProfileStatQueueMax OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum queue occupation per profile per port (in number of packets) ." ::= { msanQosPortProfileStatEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.10 msanIpAclTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanIpAclEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanQoS 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.10.1 msanIpAclEntry OBJECT-TYPE SYNTAX MsanIpAclEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanIpAclId } ::= { msanIpAclTable 1 } MsanIpAclEntry ::= SEQUENCE { msanIpAclId Integer32, msanIpAclProtection INTEGER, msanIpAclStatus INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.12.10.1.1 msanIpAclId OBJECT-TYPE SYNTAX Integer32 (1..199) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is aclIndex in aclTable (1.3.6.1.4.1.1332.1.1.5.2.3.2.1)" ::= { msanIpAclEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.10.1.2 msanIpAclProtection OBJECT-TYPE SYNTAX INTEGER { unprotected(0), protected(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanAclProfileStatus = dynamic(2)" DEFVAL { unprotected } ::= { msanIpAclEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.10.1.4 msanIpAclStatus OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Profile status. If status is dynamic, profile values can't be edited." ::= { msanIpAclEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.11 msanMacAclTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMacAclEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanQoS 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.11.1 msanMacAclEntry OBJECT-TYPE SYNTAX MsanMacAclEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanMacAclId } ::= { msanMacAclTable 1 } MsanMacAclEntry ::= SEQUENCE { msanMacAclId Integer32, msanMacAclProtection INTEGER, msanMacAclStatus INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.12.11.1.1 msanMacAclId OBJECT-TYPE SYNTAX Integer32 (1..199) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is aclMacIndex in aclMacTable (1.3.6.1.4.1.1332.1.1.5.2.3.2.6)" ::= { msanMacAclEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.11.1.3 msanMacAclProtection OBJECT-TYPE SYNTAX INTEGER { unprotected(0), protected(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanMacAclStatus = dynamic(2)" DEFVAL { unprotected } ::= { msanMacAclEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.12.11.1.4 msanMacAclStatus OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Profile status. If status is dynamic, profile values can't be edited." ::= { msanMacAclEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.13 msanForwardingDb OBJECT IDENTIFIER ::= { msanAdditionalConf 13 } -- 1.3.6.1.4.1.1332.1.1.5.3.13.3 msanForwardingDbGlobal OBJECT IDENTIFIER ::= { msanForwardingDb 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.13.3.1 msanAddressLearningMode OBJECT-TYPE SYNTAX INTEGER { macOnly(1), noMacOnly(2) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Specifies how source MAC addresses are associated with the interfaces on the switch. If mode is specified as nomaconly, source MAC addresses are learned as pairs of incoming VLAN ID and the source MAC address. If mode is specified as maconly, all source MAC addresses are learned in a specified VLAN, VLAN ID of the VLAN the packet was received from is not remembered. This mode is used for General Purpose Service Based Tagging." ::= { msanForwardingDbGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.13.3.2 msanAddressLearningVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This is the VLAN ID which is used for learning source MAC addresses in maconly mode. All learned MAC addresses will be marked as received from this VLAN. VLAN with this VLAN ID is created on the switch and all physical intefaces are added to this VLAN. This VLAN ID cannot be used for configuring other VLANs on the switch." ::= { msanForwardingDbGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.13.3.3 msanSwitchAddressAgingTimeout OBJECT-TYPE SYNTAX INTEGER (10..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The FDB entry's address aging timeout (in seconds)." DEFVAL { 300 } ::= { msanForwardingDbGlobal 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.14 msanDiagnostics OBJECT IDENTIFIER ::= { msanAdditionalConf 14 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.1 msanDiagnosticsGlobal OBJECT IDENTIFIER ::= { msanDiagnostics 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.1.1 msanDiagnosticsFanSpeedLevel OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "MSAN shelf fan current speed level. Higher level defines higer speed. Level 0 means fan is stopped. Maximum level is defined by parameter msanDiagnosticsMaxFanSpeedLevel" ::= { msanDiagnosticsGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.1.2 msanDiagnosticsMaxFanSpeedLevel OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "MSAN shelf fan max speed level." ::= { msanDiagnosticsGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.2 msanDiagnosticsTestTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanDiagnosticsTestEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanDiagnostics 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.2.1 msanDiagnosticsTestEntry OBJECT-TYPE SYNTAX MsanDiagnosticsTestEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanDiagnosticsTestCode } ::= { msanDiagnosticsTestTable 1 } MsanDiagnosticsTestEntry ::= SEQUENCE { msanDiagnosticsTestCode Integer32, msanDiagnosticsTestName OCTET STRING, msanDiagnosticsTestActivity INTEGER, msanDiagnosticsTestTime Unsigned32, msanDiagnosticsTestPriority INTEGER, msanDiagnosticsTestType INTEGER, msanDiagnosticsTestTimeMin Integer32, msanDiagnosticsTestTimeMax Integer32 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.2.1.1 msanDiagnosticsTestCode OBJECT-TYPE SYNTAX Integer32 (0..99999999) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Unique identification of a test program." ::= { msanDiagnosticsTestEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.2.1.2 msanDiagnosticsTestName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The name of a test program." ::= { msanDiagnosticsTestEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.2.1.3 msanDiagnosticsTestActivity OBJECT-TYPE SYNTAX INTEGER { testOn(1), testOff(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the Test activity parameter for the diagnostic. " ::= { msanDiagnosticsTestEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.2.1.4 msanDiagnosticsTestTime OBJECT-TYPE SYNTAX Unsigned32 (100..999999900) MAX-ACCESS read-write STATUS current DESCRIPTION "Test time, whose interpretation depends on test running mode: - for cyclical tests, it means the period at which the test is carried out one after another (time unit is milisecond) - for all others, it means time of day in the form 'hhmmss' (e.g. '224950') at which the test begins. " ::= { msanDiagnosticsTestEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.2.1.6 msanDiagnosticsTestPriority OBJECT-TYPE SYNTAX INTEGER { low(0), medium(1), high(2), veryHigh(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Test priority parameter for the diagnostic." ::= { msanDiagnosticsTestEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.2.1.7 msanDiagnosticsTestType OBJECT-TYPE SYNTAX INTEGER { testAtReload(1), testPeriodically(2), testDaily(3) } MAX-ACCESS read-only STATUS current DESCRIPTION " Type of starting the test. DECIMAL VALUE DESCRIPTION 1 At start-up & Recovery 2 Periodical 3 Daily " ::= { msanDiagnosticsTestEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.2.1.8 msanDiagnosticsTestTimeMin OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum possible value of parameter msanDiagnosticTestTime." ::= { msanDiagnosticsTestEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.2.1.9 msanDiagnosticsTestTimeMax OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum possible value of parameter msanDiagnosticTestTime." ::= { msanDiagnosticsTestEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.3 msanDiagnosticsErrorTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanDiagnosticsErrorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanDiagnostics 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.3.1 msanDiagnosticsErrorEntry OBJECT-TYPE SYNTAX MsanDiagnosticsErrorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanDiagnosticsErrorCode } ::= { msanDiagnosticsErrorTable 1 } MsanDiagnosticsErrorEntry ::= SEQUENCE { msanDiagnosticsErrorCode Integer32, msanDiagnosticsErrorDescription OCTET STRING, msanDiagnosticsErrorPriority INTEGER, msanDiagnosticsErrorObjectType OCTET STRING, msanDiagnosticsErrorMeasure OCTET STRING, msanDiagnosticsErrorMeasureActive INTEGER, msanDiagnosticsErrorProbableCause Integer32, msanDiagnosticsErrorObjectTypeId Integer32, msanDiagnosticsErrorMeasureId Integer32 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.3.1.1 msanDiagnosticsErrorCode OBJECT-TYPE SYNTAX Integer32 (0..99999999) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Unique identification of an error reported during testing an object." ::= { msanDiagnosticsErrorEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.3.1.2 msanDiagnosticsErrorDescription OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Description of the error code." ::= { msanDiagnosticsErrorEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.3.1.3 msanDiagnosticsErrorPriority OBJECT-TYPE SYNTAX INTEGER { critical(1), major(2), minor(3), warning(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Error priority." ::= { msanDiagnosticsErrorEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.3.1.4 msanDiagnosticsErrorObjectType OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Object type - List of values can be found in alr_def.h" ::= { msanDiagnosticsErrorEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.3.1.5 msanDiagnosticsErrorMeasure OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Measure (what is done when an error occurs, for instance reset the node, ...) - List of values can be found in alr_def.h" ::= { msanDiagnosticsErrorEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.3.1.6 msanDiagnosticsErrorMeasureActive OBJECT-TYPE SYNTAX INTEGER { notActive(0), active(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Activity of measure. With setting this parameter to notActive(0), you can prevent excecution of measure." DEFVAL { active } ::= { msanDiagnosticsErrorEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.3.1.7 msanDiagnosticsErrorProbableCause OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Probable cause." ::= { msanDiagnosticsErrorEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.3.1.8 msanDiagnosticsErrorObjectTypeId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Object type ID- List of values can be found in alr_def.h" ::= { msanDiagnosticsErrorEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.3.1.9 msanDiagnosticsErrorMeasureId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Measure (what is done when an error occurs, for instance reset the node, ...) - List of values can be found in alr_def.h" ::= { msanDiagnosticsErrorEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.4 msanDiagnosticsTempTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanDiagnosticsTempEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanDiagnostics 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.4.1 msanDiagnosticsTempEntry OBJECT-TYPE SYNTAX MsanDiagnosticsTempEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanDiagnosticsTempSensorID } ::= { msanDiagnosticsTempTable 1 } MsanDiagnosticsTempEntry ::= SEQUENCE { msanDiagnosticsTempSensorID Integer32, msanDiagnosticsTempSensorName OCTET STRING, msanDiagnosticsTempCurrent Integer32, msanDiagnosticsTempCriticUnderheatThreshold Integer32, msanDiagnosticsTempUnderheatThreshold Integer32, msanDiagnosticsTempOverheatThreshold Integer32, msanDiagnosticsTempCriticOverheatThreshold Integer32 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.4.1.1 msanDiagnosticsTempSensorID OBJECT-TYPE SYNTAX Integer32 (0..100) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Temperature sensor ID." ::= { msanDiagnosticsTempEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.4.1.2 msanDiagnosticsTempSensorName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Temperature sensor name." ::= { msanDiagnosticsTempEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.4.1.3 msanDiagnosticsTempCurrent OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current temperature of the specified sensor in [deg C]." ::= { msanDiagnosticsTempEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.4.1.4 msanDiagnosticsTempCriticUnderheatThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Sensor critical underheat threshold temperature limit in [deg C]." ::= { msanDiagnosticsTempEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.4.1.5 msanDiagnosticsTempUnderheatThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Sensor underheat temperature threshold limit in [deg C]." ::= { msanDiagnosticsTempEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.4.1.6 msanDiagnosticsTempOverheatThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Sensor overheat threshold temperature limit in [deg C]." ::= { msanDiagnosticsTempEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.4.1.7 msanDiagnosticsTempCriticOverheatThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Sensor critical overheat threshold temperature limit in [deg C]." ::= { msanDiagnosticsTempEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.5 msanDiagnosticsErrorFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanDiagnosticsErrorFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanDiagnostics 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.5.1 msanDiagnosticsErrorFilterEntry OBJECT-TYPE SYNTAX MsanDiagnosticsErrorFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanDiagnosticsErrorFilterErrMask, msanDiagnosticsErrorFilterObjMask } ::= { msanDiagnosticsErrorFilterTable 1 } MsanDiagnosticsErrorFilterEntry ::= SEQUENCE { msanDiagnosticsErrorFilterErrMask OCTET STRING, msanDiagnosticsErrorFilterObjMask OCTET STRING, msanDiagnosticsErrorFilterRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.14.5.1.1 msanDiagnosticsErrorFilterErrMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Error code in ascii format. Regular expression describing one or more error codes." ::= { msanDiagnosticsErrorFilterEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.5.1.2 msanDiagnosticsErrorFilterObjMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..40)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Type of object, which alarming is filtered for. Regular expression describing one or more test objects. " ::= { msanDiagnosticsErrorFilterEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.5.1.3 msanDiagnosticsErrorFilterRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanDiagnosticsErrorFilterEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.6 msanDiagnosticsErrorSeverityTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanDiagnosticsErrorSeverityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanDiagnostics 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.6.1 msanDiagnosticsErrorSeverityEntry OBJECT-TYPE SYNTAX MsanDiagnosticsErrorSeverityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanDiagnosticsErrorSeverityErrCode, msanDiagnosticsErrorSeverityObjMask } ::= { msanDiagnosticsErrorSeverityTable 1 } MsanDiagnosticsErrorSeverityEntry ::= SEQUENCE { msanDiagnosticsErrorSeverityErrCode Integer32, msanDiagnosticsErrorSeverityErrPriority INTEGER, msanDiagnosticsErrorSeverityObjMask OCTET STRING, msanDiagnosticsErrorSeverityRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.14.6.1.1 msanDiagnosticsErrorSeverityErrCode OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Unique identification of an error reported during testing an object. All error codes are stated in alr_def.h (KFMT)" ::= { msanDiagnosticsErrorSeverityEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.6.1.2 msanDiagnosticsErrorSeverityErrPriority OBJECT-TYPE SYNTAX INTEGER { critical(1), major(2), minor(3), warning(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Priority of error. " ::= { msanDiagnosticsErrorSeverityEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.6.1.3 msanDiagnosticsErrorSeverityObjMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..40)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Type of object, which alarming is filtered for. Regular expression describing one or more test objects. " ::= { msanDiagnosticsErrorSeverityEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.14.6.1.4 msanDiagnosticsErrorSeverityRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5) [createAndGo(4) is not supported]. " ::= { msanDiagnosticsErrorSeverityEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.15 msanPpp OBJECT IDENTIFIER ::= { msanAdditionalConf 15 } -- 1.3.6.1.4.1.1332.1.1.5.3.15.1 msanPppGlobal OBJECT IDENTIFIER ::= { msanPpp 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.15.1.1 msanPppLocalIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Local IP address for PPP connection" ::= { msanPppGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.15.1.2 msanPppRemoteIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Remote IP address for PPP connection" ::= { msanPppGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.15.1.3 msanPppAuthProtocol OBJECT-TYPE SYNTAX INTEGER { none(0), chap(1), pap(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "PPP authentication protocol. For MPS connection use CHAP." ::= { msanPppGlobal 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.15.1.4 msanPppEchoInterval OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "LCP echo interval (in seconds) for session breakdown identification." ::= { msanPppGlobal 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.15.1.5 msanPppVanJacobsonCompression OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Control of VanJacobson compression. For MPS connection it must be disabled." ::= { msanPppGlobal 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.15.1.6 msanPppAdminState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Global PPP connection administrative state." ::= { msanPppGlobal 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.16 msanAlarmPanel OBJECT IDENTIFIER ::= { msanAdditionalConf 16 } -- 1.3.6.1.4.1.1332.1.1.5.3.16.1 msanAlarmPanelGlobal OBJECT IDENTIFIER ::= { msanAlarmPanel 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.16.1.1 msanAlarmPanelAudioAlarmPriority OBJECT-TYPE SYNTAX INTEGER { critical(1), major(2), minor(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Alarm Panel Audio Alarm Priority." ::= { msanAlarmPanelGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.16.1.2 msanAlarmPanelSerialPortType OBJECT-TYPE SYNTAX INTEGER { noConnection(1), mps(2), alarmPanel(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type of equipment connected to serial port." ::= { msanAlarmPanelGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.16.2 msanAlarmPanelTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanAlarmPanelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanAlarmPanel 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.16.2.1 msanAlarmPanelEntry OBJECT-TYPE SYNTAX MsanAlarmPanelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanAlarmPanelIndex } ::= { msanAlarmPanelTable 1 } MsanAlarmPanelEntry ::= SEQUENCE { msanAlarmPanelIndex Integer32, msanAlarmPanelConnectionState INTEGER, msanAlarmPanelAdminState INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.16.2.1.1 msanAlarmPanelIndex OBJECT-TYPE SYNTAX Integer32 (1..16) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Unique identification of an alarm panel." ::= { msanAlarmPanelEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.16.2.1.2 msanAlarmPanelConnectionState OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Alarm panel connection status" ::= { msanAlarmPanelEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.16.2.1.3 msanAlarmPanelAdminState OBJECT-TYPE SYNTAX INTEGER { unequipped(0), equipped(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Flag determining whether an alarm panel is equipped or not." ::= { msanAlarmPanelEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.16.3 msanAlarmPanelIndicatorTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanAlarmPanelIndicatorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanAlarmPanel 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.16.3.1 msanAlarmPanelIndicatorEntry OBJECT-TYPE SYNTAX MsanAlarmPanelIndicatorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanAlarmPanelIndex, msanAlarmPanelIndicatorIndex } ::= { msanAlarmPanelIndicatorTable 1 } MsanAlarmPanelIndicatorEntry ::= SEQUENCE { msanAlarmPanelIndicatorIndex Integer32, msanAlarmPanelIndicatorErrCode Integer32 } -- 1.3.6.1.4.1.1332.1.1.5.3.16.3.1.1 msanAlarmPanelIndicatorIndex OBJECT-TYPE SYNTAX Integer32 (1..15) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Alarm panel indicator number. " ::= { msanAlarmPanelIndicatorEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.16.3.1.2 msanAlarmPanelIndicatorErrCode OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Alarm panel indicator error number." ::= { msanAlarmPanelIndicatorEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.16.4 msanAlarmPanelInputTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanAlarmPanelInputEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanAlarmPanel 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.16.4.1 msanAlarmPanelInputEntry OBJECT-TYPE SYNTAX MsanAlarmPanelInputEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanAlarmPanelIndex, msanAlarmPanelInputIndex } ::= { msanAlarmPanelInputTable 1 } MsanAlarmPanelInputEntry ::= SEQUENCE { msanAlarmPanelInputIndex Integer32, msanAlarmPanelInputErrCode Integer32, msanAlarmPanelInputActiveLevel INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.16.4.1.1 msanAlarmPanelInputIndex OBJECT-TYPE SYNTAX Integer32 (1..15) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Alarm panel input sensor number." ::= { msanAlarmPanelInputEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.16.4.1.2 msanAlarmPanelInputErrCode OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Alarm panel input sensor error code." ::= { msanAlarmPanelInputEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.16.4.1.3 msanAlarmPanelInputActiveLevel OBJECT-TYPE SYNTAX INTEGER { low(0), high(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Alarm panel input sensor active level." ::= { msanAlarmPanelInputEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.17 msanMvr OBJECT IDENTIFIER ::= { msanAdditionalConf 17 } -- 1.3.6.1.4.1.1332.1.1.5.3.17.1 msanMvrGlobal OBJECT IDENTIFIER ::= { msanMvr 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.17.2 msanMvrPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMvrPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanMvr 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.17.2.1 msanMvrPortEntry OBJECT-TYPE SYNTAX MsanMvrPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanMvrPortTable 1 } MsanMvrPortEntry ::= SEQUENCE { msanMvrPortAdminMode INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.17.2.1.1 msanMvrPortAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administrative mode for Multicast VLAN Registration (a.k.a. Service Based Tagging) for the selected interface" ::= { msanMvrPortEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.17.3 msanMvrMulticastGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMvrMulticastGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanMvr 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.17.3.1 msanMvrMulticastGroupEntry OBJECT-TYPE SYNTAX MsanMvrMulticastGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanMvrMulticastGroupMVlanId, msanMvrMulticastGroupStartIp } ::= { msanMvrMulticastGroupTable 1 } MsanMvrMulticastGroupEntry ::= SEQUENCE { msanMvrMulticastGroupMVlanId Integer32, msanMvrMulticastGroupStartIp IpAddress, msanMvrMulticastGroupEndIp IpAddress, msanMvrMulticastGroupRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.17.3.1.1 msanMvrMulticastGroupMVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "VLAN ID (refers to dot1qVlanIndex) where MVR functionality is used." ::= { msanMvrMulticastGroupEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.17.3.1.2 msanMvrMulticastGroupStartIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Start IP Address of the multicast group range." ::= { msanMvrMulticastGroupEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.17.3.1.3 msanMvrMulticastGroupEndIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "End IP Address of the multicast group range." ::= { msanMvrMulticastGroupEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.17.3.1.4 msanMvrMulticastGroupRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported]." ::= { msanMvrMulticastGroupEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.17.4 msanMvrConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMvrConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanMvr 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.17.4.1 msanMvrConfigEntry OBJECT-TYPE SYNTAX MsanMvrConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex, msanMvrConfigCVlanId, msanMvrConfigMVlanId } ::= { msanMvrConfigTable 1 } MsanMvrConfigEntry ::= SEQUENCE { msanMvrConfigCVlanId Integer32, msanMvrConfigMVlanId Integer32, msanMvrConfigCos Integer32, msanMvrConfigRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.17.4.1.1 msanMvrConfigCVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Customer VLAN ID for the selected interface from which IGMP Join/Leave messages will be remarked." ::= { msanMvrConfigEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.17.4.1.2 msanMvrConfigMVlanId OBJECT-TYPE SYNTAX Integer32 (1..4092) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Service provider multicast VLAN ID for the selected interface to which IGMP Join/Leave messages will be remarked." ::= { msanMvrConfigEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.17.4.1.3 msanMvrConfigCos OBJECT-TYPE SYNTAX Integer32 (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Output CoS priority on the selected interface. IGMP messages received from this interface will have this priority when they are transmitted into service provider multicast VLAN. Value '-1' defines that original CoS value is not changed." DEFVAL { 0 } ::= { msanMvrConfigEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.17.4.1.4 msanMvrConfigRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanMvrConfigEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.17.5 msanMvrDvlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMvrDvlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanMvr 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.17.5.1 msanMvrDvlanEntry OBJECT-TYPE SYNTAX MsanMvrDvlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanMvrDvlanTable 1 } MsanMvrDvlanEntry ::= SEQUENCE { msanMvrDvlanRmOuterTagStatus INTEGER, msanMvrDvlanEthertypeRewriteStatus INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.17.5.1.1 msanMvrDvlanRmOuterTagStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The desired state of removing outer tags on IGMP packets funcionality." DEFVAL { disable } ::= { msanMvrDvlanEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.17.5.1.2 msanMvrDvlanEthertypeRewriteStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The desired state of rewriting ether type from outer vlan tag to inner vlan tag." DEFVAL { disable } ::= { msanMvrDvlanEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.18 msanRemoteAccess OBJECT IDENTIFIER ::= { msanAdditionalConf 18 } -- 1.3.6.1.4.1.1332.1.1.5.3.18.1 msanRemoteAccessGlobal OBJECT IDENTIFIER ::= { msanRemoteAccess 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.18.2 msanRemoteAccessFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanRemoteAccessFilterEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." ::= { msanRemoteAccess 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.18.2.1 msanRemoteAccessFilterEntry OBJECT-TYPE SYNTAX MsanRemoteAccessFilterEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." INDEX { msanRemoteAccessFilterRuleIndex } ::= { msanRemoteAccessFilterTable 1 } MsanRemoteAccessFilterEntry ::= SEQUENCE { msanRemoteAccessFilterRuleIndex INTEGER, msanRemoteAccessFilterIp IpAddress, msanRemoteAccessFilterNetmask IpAddress, msanRemoteAccessFilterAction INTEGER, msanRemoteAccessFilterRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.18.2.1.1 msanRemoteAccessFilterRuleIndex OBJECT-TYPE SYNTAX INTEGER (1..200) MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Rule's index. Index should be continued, without gaps. " ::= { msanRemoteAccessFilterEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.18.2.1.2 msanRemoteAccessFilterIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS deprecated DESCRIPTION "IP Address of the rule." ::= { msanRemoteAccessFilterEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.18.2.1.3 msanRemoteAccessFilterNetmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS deprecated DESCRIPTION "Netmask of the rule." ::= { msanRemoteAccessFilterEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.18.2.1.4 msanRemoteAccessFilterAction OBJECT-TYPE SYNTAX INTEGER { accept(1), deny(2) } MAX-ACCESS read-create STATUS deprecated DESCRIPTION "Action to be taken with a packet: accept or deny it." ::= { msanRemoteAccessFilterEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.18.2.1.5 msanRemoteAccessFilterRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported]." ::= { msanRemoteAccessFilterEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.19 msanDslSpecific OBJECT IDENTIFIER ::= { msanAdditionalConf 19 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.1 msanDslSpecificGlobal OBJECT IDENTIFIER ::= { msanDslSpecific 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.1.1 msanDslSpecificSystemState OBJECT-TYPE SYNTAX INTEGER { operational(4), notReady(12) } MAX-ACCESS read-only STATUS current DESCRIPTION "VDSL system operational state. For normal blade operation this value should be operational (4). If value differ from 4, VDSL driver is not operational." ::= { msanDslSpecificGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.1.2 msanDslSpecificSystemFirmware OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "VDSL firmware version." ::= { msanDslSpecificGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3 msanDslSpecificTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanDslSpecificEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanDslSpecific 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1 msanDslSpecificEntry OBJECT-TYPE SYNTAX MsanDslSpecificEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanDslSpecificTable 1 } MsanDslSpecificEntry ::= SEQUENCE { msanDslSpecificDsPsdMask OCTET STRING, msanDslSpecificUsPsdMask OCTET STRING, msanDslSpecificLineState INTEGER, msanDslSpecificMaxDelayDs Integer32, msanDslSpecificMaxDelayUs Integer32, msanDslSpecificMinProtectionDs Integer32, msanDslSpecificMinProtectionUs Integer32, msanDslSpecificMaxSnrmDs Unsigned32, msanDslSpecificMinSnrmDs Unsigned32, msanDslSpecificMaxSnrmUs Unsigned32, msanDslSpecificMinSnrmUs Unsigned32, msanDslSpecificRaUsNrmDs Unsigned32, msanDslSpecificRaUsNrmUs Unsigned32, msanDslSpecificRaUsTimeDs Unsigned32, msanDslSpecificRaUsTimeUs Unsigned32, msanDslSpecificRaDsNrmDs Unsigned32, msanDslSpecificRaDsNrmUs Unsigned32, msanDslSpecificRaDsTimeDs Unsigned32, msanDslSpecificRaDsTimeUs Unsigned32, msanDslSpecificL0Time Unsigned32, msanDslSpecificL2Time Unsigned32, msanDslSpecificL2Atpr Unsigned32, msanDslSpecificL2Atprt Unsigned32, msanDslSpecificScMaskDs OCTET STRING, msanDslSpecificScMaskUs OCTET STRING, msanDslSpecificRfiBands OCTET STRING, msanDslSpecificMaxNomPsdDs Integer32, msanDslSpecificMaxNomPsdUs Integer32, msanDslSpecificMaxNomAtpDs Unsigned32, msanDslSpecificMaxNomAtpUs Unsigned32, msanDslSpecificMaxAggRxPwrUs Integer32, msanDslSpecificClassMask INTEGER, msanDslSpecificDpboEsEL Unsigned32, msanDslSpecificUpboKLF INTEGER, msanDslSpecificUpboKL Unsigned32, msanDslSpecificSelt INTEGER, msanDslSpecificSeltStatus INTEGER, msanDslSpecificPhyRDs INTEGER, msanDslSpecificPhyRUs INTEGER, msanDslSpecificUpboUs1a INTEGER, msanDslSpecificUpboUs1b INTEGER, msanDslSpecificUpboUs2a INTEGER, msanDslSpecificUpboUs2b INTEGER, msanDslSpecificUpboUs3a INTEGER, msanDslSpecificUpboUs3b INTEGER, msanDslSpecificUpboUs4a INTEGER, msanDslSpecificUpboUs4b INTEGER, msanDslSpecificDpboEPsdMask OCTET STRING, msanDslSpecificDpboEsCmA Unsigned32, msanDslSpecificDpboEsCmB Unsigned32, msanDslSpecificDpboEsCmC Unsigned32, msanDslSpecificDpboMus Unsigned32, msanDslSpecificDpboFMin Unsigned32, msanDslSpecificDpboFMax Unsigned32 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.1 msanDslSpecificDsPsdMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Unique name of the downstream PSD mask as defined by msanDslPsdMaskDsName." DEFVAL { "" } ::= { msanDslSpecificEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.2 msanDslSpecificUsPsdMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Unique name of the upstream PSD mask as defined by msanDslPsdMaskUsName." DEFVAL { "ANSI_FTTCab_M11" } ::= { msanDslSpecificEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.3 msanDslSpecificLineState OBJECT-TYPE SYNTAX INTEGER { quiet(0), idle(1), activateInitTrain(2), activeFullPower(3), activeLowPower(4), unitFail(5), atpPtmLoopback(6), dspDigitalLoopback(7), lineDriverDigitalLoopback(8), hybridLoopback(9), testMode(10), loopDiagnosticsDeltInit(11), loopDiagnosticsDelt(12), seltInits(13), selt(14) } MAX-ACCESS read-only STATUS current DESCRIPTION "VDSL system operational state. For normal blade operation this value should be active(3). If value is differ from 3, VDSL driver is not operational." ::= { msanDslSpecificEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.4 msanDslSpecificMaxDelayDs OBJECT-TYPE SYNTAX Integer32 (-1..63) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum interleave delay for the downstream interleaved channel. -1 means that value from profile will be used (xdsl2ChConfProfMaxDelayDs). This object is created based on xdsl2ChConfProfMaxDelayDs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.5 msanDslSpecificMaxDelayUs OBJECT-TYPE SYNTAX Integer32 (-1..63) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum interleave delay for the upstream interleaved channel. -1 means that value from profile will be used (xdsl2ChConfProfMaxDelayUs). This object is created based on xdsl2ChConfProfMaxDelayUs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.6 msanDslSpecificMinProtectionDs OBJECT-TYPE SYNTAX Integer32 (-1..160) UNITS "symbols" MAX-ACCESS read-write STATUS current DESCRIPTION "Downstream impulse noise protection. -1 means that value from profile will be used (xdsl2ChConfProfMinProtectionDs) This object is created based on xdsl2ChConfProfMinProtectionDs(VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.7 msanDslSpecificMinProtectionUs OBJECT-TYPE SYNTAX Integer32 (-1..160) MAX-ACCESS read-write STATUS current DESCRIPTION "Upstream impulse noise protection. -1 means that value from profile will be used (xdsl2ChConfProfMinProtectionUs) This object is created based on xdsl2ChConfProfMinProtectionUs(VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.8 msanDslSpecificMaxSnrmDs OBJECT-TYPE SYNTAX Unsigned32 (0..310) UNITS "0.1 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Downstream maximum Signal/Noise Margin. This object is created based on xdsl2LConfProfMaxSnrmDs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.9 msanDslSpecificMinSnrmDs OBJECT-TYPE SYNTAX Unsigned32 (0..310) UNITS "0.1 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Downstream minimum Signal/Noise Margin. This object is created based on xdsl2LConfProfMinSnrmDs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.10 msanDslSpecificMaxSnrmUs OBJECT-TYPE SYNTAX Unsigned32 (0..310) UNITS "0.1 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Upstream maximum Signal/Noise Margin. This object is created based on xdsl2LConfProfMaxSnrmUs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.11 msanDslSpecificMinSnrmUs OBJECT-TYPE SYNTAX Unsigned32 (0..310) UNITS "0.1 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Upstream minimum Signal/Noise Margin. This object is created based on xdsl2LConfProfMinSnrmUs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.12 msanDslSpecificRaUsNrmDs OBJECT-TYPE SYNTAX Unsigned32 (0..310) UNITS "0.1 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "The Downstream Up-Shift Noise Margin (for dynamic rate adaptive mode). This object is created based on xdsl2LConfProfRaUsNrmDs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.13 msanDslSpecificRaUsNrmUs OBJECT-TYPE SYNTAX Unsigned32 (0..310) UNITS "0.1 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "The Upstream Up-Shift Noise Margin (for dynamic rate adaptive mode). This object is created based on xdsl2LConfProfRaUsNrmUs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 13 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.14 msanDslSpecificRaUsTimeDs OBJECT-TYPE SYNTAX Unsigned32 (0..16383) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The Downstream Up-Shift Time Interval (for rate dynamic adaptive mode). This object is created based on xdsl2LConfProfRaUsTimeDs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 14 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.15 msanDslSpecificRaUsTimeUs OBJECT-TYPE SYNTAX Unsigned32 (0..16383) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The Upstream Up-Shift Time Interval (for rate dynamic adaptive mode). This object is created based on xdsl2LConfProfRaUsTimeUs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 15 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.16 msanDslSpecificRaDsNrmDs OBJECT-TYPE SYNTAX Unsigned32 (0..310) UNITS "0.1 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "The Downstream Down-Shift Noise Margin (for dynamic rate adaptive mode). This object is created based on xdsl2LConfProfRaDsNrmDs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 16 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.17 msanDslSpecificRaDsNrmUs OBJECT-TYPE SYNTAX Unsigned32 (0..310) UNITS "0.1 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "The Upstream Down-Shift Noise Margin (for dynamic rate adaptive mode). This object is created based on xdsl2LConfProfRaDsNrmUs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 17 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.18 msanDslSpecificRaDsTimeDs OBJECT-TYPE SYNTAX Unsigned32 (0..16383) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The Downstream Down-Shift Time Interval (for rate dynamic adaptive mode). This object is created based on xdsl2LConfProfRaDsTimeDs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 18 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.19 msanDslSpecificRaDsTimeUs OBJECT-TYPE SYNTAX Unsigned32 (0..16383) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The Upstream Down-Shift Time Interval (for rate dynamic adaptive mode). This object is created based on xdsl2LConfProfRaDsTimeUs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 19 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.20 msanDslSpecificL0Time OBJECT-TYPE SYNTAX Unsigned32 (0..255) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The minimum time between an exit from the L2 state and the next entry into the L2 state. This object is created based on xdsl2LConfProfL0Time (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 20 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.21 msanDslSpecificL2Time OBJECT-TYPE SYNTAX Unsigned32 (0..255) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The minimum time between an entry into the L2 state and the first power trim in the L2 state and between two consecutive power trims in the L2 State. This object is created based on xdsl2LConfProfL2Time (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 21 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.22 msanDslSpecificL2Atpr OBJECT-TYPE SYNTAX Unsigned32 (0..31) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum aggregate transmit power reduction that can be performed at transition of L0 to L2 state or through a single power trim in the L2 state. This object is created based on xdsl2LConfProfL2Atpr (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 22 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.23 msanDslSpecificL2Atprt OBJECT-TYPE SYNTAX Unsigned32 (0..31) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "The total maximum aggregate transmit power reduction that can be performed in an L2 state. This object is created based on xdsl2LConfProfL2Atprt (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 23 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.24 msanDslSpecificScMaskDs OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..512)) MAX-ACCESS read-write STATUS current DESCRIPTION "Downstream Sub-carriers mask. A bitmap of 4096 bits that allows masking up to 4096 downstream sub-carriers. If bit is set to '1', the respective downstream sub-carrier is masked (not used), and if set to '0', the respective sub-carrier is unmasked. This object is created based on xdsl2LConfProfScMaskDs (VDSL2-LINE MIB) " ::= { msanDslSpecificEntry 24 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.25 msanDslSpecificScMaskUs OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..512)) MAX-ACCESS read-write STATUS current DESCRIPTION "Upstream Sub-carriers mask. A bitmap of 4096 bits that allows masking up to 4096 downstream sub-carriers. If bit is set to '1', the respective downstream sub-carrier is masked (not used), and if set to '0', the respective sub-carrier is unmasked. This object is created based on xdsl2LConfProfScMaskUs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 25 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.26 msanDslSpecificRfiBands OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "For VDLS, this configuration parameter defines the bands where the PSD shall be reduced. Each band shall be represented by a start and stop subcarrier indices with a subcarrier spacing of 4.3125 kHz. Up to 16 bands may be specified. This parameter defines the RFI bands for both upstream and downstream directions. Each RFI band is represented by 4 octets: 16 bit start sub-carrier index followed by a 16 bit stop sub-carrier index. This object is created based on xdsl2LConfProfRfiBands (VDSL2-LINE MIB) " ::= { msanDslSpecificEntry 26 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.27 msanDslSpecificMaxNomPsdDs OBJECT-TYPE SYNTAX Integer32 (-600..-300) UNITS "0.1 dBm/Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum nominal transmit PSD in the downstream direction during initialization and Showtime. (0.1 dBm/Hz - physical values are -60 to -30 dBm/Hz). This object is created based on xdsl2LConfProfMaxNomPsdDs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 27 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.28 msanDslSpecificMaxNomPsdUs OBJECT-TYPE SYNTAX Integer32 (-600..-300) UNITS "0.1 dBm/Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum nominal transmit PSD in the upstream direction during initialization and Showtime. (0.1 dBm/Hz - physical values are -60 to -30 dBm/Hz). This object is created based on xdsl2LConfProfMaxNomPsdUs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 28 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.29 msanDslSpecificMaxNomAtpDs OBJECT-TYPE SYNTAX Unsigned32 (0..255) UNITS "0.1 dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum nominal aggregate transmit power in the downstream direction during initialization and Showtime. (0.1 dBm - physical values are 0 to 25.5 dBm). This object is created based on xdsl2LConfProfMaxNomAtpDs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 29 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.30 msanDslSpecificMaxNomAtpUs OBJECT-TYPE SYNTAX Unsigned32 (0..255) UNITS "0.1 dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum nominal aggregate transmit power in the upstream direction during initialization and Showtime. (0.1 dBm - physical values are 0 to 25.5 dBm). This object is created based on xdsl2LConfProfMaxNomAtpUs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 30 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.31 msanDslSpecificMaxAggRxPwrUs OBJECT-TYPE SYNTAX Integer32 (-255..255) UNITS "0.1 dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum upstream aggregate receive power over the relevant set of sub-carriers.. (0.1 dBm - physical values are -25.5 to 25.5 dBm). This object is created based on xdsl2LConfProfMaxAggRxPwrUs (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 31 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.32 msanDslSpecificClassMask OBJECT-TYPE SYNTAX INTEGER { b998_M1x_A(1), b998_M1x_B(2), b998_M1x_NUS0(3), b998_M2x_A(4), b998_M2x_M(5), b998_M2x_B(6), b998_M2x_NUS0(7), b998E17_M2x_NUS0(8), b998E17_M2x_NUS0_M(9), b998ADE17_M2x_NUS0_M(10), b998ADE17_M2x_A(11), b998ADE17_M2x_B(12), b997_M1c_A_7(13), b997_M1x_M_8(14), b997_M1x_M(15), b997_M2x_M_8(16), b997_M2x_A(17), b997_M2x_M(18), bHPE17_M1_NUS0(19), bHPE30_M1_NUS0(20), b997E17_M2x_A(21) } MAX-ACCESS read-write STATUS current DESCRIPTION "Predefined PSD mask. This object is created based on xdsl2LConfProfClassMask (VDSL2-LINE MIB)" DEFVAL { b998E17_M2x_NUS0 } ::= { msanDslSpecificEntry 32 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.35 msanDslSpecificDpboEsEL OBJECT-TYPE SYNTAX Unsigned32 (0..511) UNITS "0.5 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Assumed electrical length of cables (E-side cables) connecting exchange based DSL services to a remote flexibility point (cabinet). The electrical length is defined as the loss (in dB) of an equivalent length of hypothetical cable at a reference frequency. 0 dB (coded as 0) to 255.5 dB (coded as 511) in steps of 0.5 dB. This object is created based on xdsl2LConfProfDpboEsEL (VDSL2-LINE MIB) " ::= { msanDslSpecificEntry 35 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.36 msanDslSpecificUpboKLF OBJECT-TYPE SYNTAX INTEGER { auto(1), override(2), disableUpbo(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Defines the upstream power backoff force mode. The three possible mode values are: auto(1), override(2), disableUpbo(3). This object is created based on xdsl2LConfProfUpboKLF (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 36 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.37 msanDslSpecificUpboKL OBJECT-TYPE SYNTAX Unsigned32 (0..1280) UNITS "0.1 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "This configuration parameter defines the electrical length expressed in dB at 1MHz, configured by the CO-MIB. The value ranges from 0 (coded as 0) to 128 dB (coded as 1280) in steps of 0.1 dB. This object is created based on xdsl2LConfProfUpboKL (VDSL2-LINE MIB)" ::= { msanDslSpecificEntry 37 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.39 msanDslSpecificSelt OBJECT-TYPE SYNTAX INTEGER { inhibit(1), force(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Defines whether the line should be forced into the SELT (Single-Ended Loop Testing) diagnostics mode by the near-end xTU of this line. Upon completion of the loop diagnostic mode procedures, the Access Node shall set this object to 'inhibit'. The results of the SELT procedure are stored in the table msanDslSeltStatusTable. The status of the loop diagnostic procedure is indicated by msanDslSpecificSeltStatus. " DEFVAL { inhibit } ::= { msanDslSpecificEntry 39 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.40 msanDslSpecificSeltStatus OBJECT-TYPE SYNTAX INTEGER { none(1), success(2), inProgress(3), unsupported(4), cannotRun(5), aborted(6), failed(7), illegalMode(8), adminUp(9), tableFull(10), noResources(11), undefinedError(12) } MAX-ACCESS read-only STATUS current DESCRIPTION "SELT (Single-Ended Loop Testing) status of dsl line. " ::= { msanDslSpecificEntry 40 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.41 msanDslSpecificPhyRDs OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), auto(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Physical Layer Retransmission configuration in the downstream direction. " DEFVAL { auto } ::= { msanDslSpecificEntry 41 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.42 msanDslSpecificPhyRUs OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), auto(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Physical Layer Retransmission configuration in the upstream direction. " DEFVAL { auto } ::= { msanDslSpecificEntry 42 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.43 msanDslSpecificUpboUs1a OBJECT-TYPE SYNTAX INTEGER (4000..8095) UNITS "0.01 dBm/Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOPSD-pb) Parameter defines the 'a' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. A UPBO PSD defined for each band shall consist of two parameters [a, b]. Parameter 'a' (xdsl2LConfProfUpboPsdA) ranges from 40 dBm/Hz (coded as 4000) to 80.95 dBm/Hz (coded as 8095) in steps of 0.01 dBm/Hz; and parameter 'b' (xdsl2LConfProfUpboPsdB) ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency 'f' expressed in MHz shall be equal to '-a-b(SQRT(f))'. Setting xdsl2LConfProfUpboPsdA to 4000 and xdsl2LConfProfUpboPsdB to 0 is a special configuration to disable UPBO in the respective upstream band." DEFVAL { 4000 } ::= { msanDslSpecificEntry 43 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.44 msanDslSpecificUpboUs1b OBJECT-TYPE SYNTAX INTEGER (0..4095) UNITS "0.01 dBm/Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOPSD-pb) Parameter defines the 'b' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. Parameter 'b' (xdsl2LConfProfUpboPsdB) ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. " DEFVAL { 0 } ::= { msanDslSpecificEntry 44 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.45 msanDslSpecificUpboUs2a OBJECT-TYPE SYNTAX INTEGER (4000..8095) UNITS "0.01 dBm/Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOPSD-pb) Parameter defines the 'a' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. A UPBO PSD defined for each band shall consist of two parameters [a, b]. Parameter 'a' (xdsl2LConfProfUpboPsdA) ranges from 40 dBm/Hz (coded as 4000) to 80.95 dBm/Hz (coded as 8095) in steps of 0.01 dBm/Hz; and parameter 'b' (xdsl2LConfProfUpboPsdB) ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency 'f' expressed in MHz shall be equal to '-a-b(SQRT(f))'. Setting xdsl2LConfProfUpboPsdA to 4000 and xdsl2LConfProfUpboPsdB to 0 is a special configuration to disable UPBO in the respective upstream band." DEFVAL { 4000 } ::= { msanDslSpecificEntry 45 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.46 msanDslSpecificUpboUs2b OBJECT-TYPE SYNTAX INTEGER (0..4095) UNITS "0.01 dBm/Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOPSD-pb) Parameter defines the 'b' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. Parameter 'b' (xdsl2LConfProfUpboPsdB) ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. " DEFVAL { 0 } ::= { msanDslSpecificEntry 46 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.47 msanDslSpecificUpboUs3a OBJECT-TYPE SYNTAX INTEGER (4000..8095) UNITS "0.01 dBm/Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOPSD-pb) Parameter defines the 'a' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. A UPBO PSD defined for each band shall consist of two parameters [a, b]. Parameter 'a' (xdsl2LConfProfUpboPsdA) ranges from 40 dBm/Hz (coded as 4000) to 80.95 dBm/Hz (coded as 8095) in steps of 0.01 dBm/Hz; and parameter 'b' (xdsl2LConfProfUpboPsdB) ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency 'f' expressed in MHz shall be equal to '-a-b(SQRT(f))'. Setting xdsl2LConfProfUpboPsdA to 4000 and xdsl2LConfProfUpboPsdB to 0 is a special configuration to disable UPBO in the respective upstream band." DEFVAL { 4000 } ::= { msanDslSpecificEntry 47 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.48 msanDslSpecificUpboUs3b OBJECT-TYPE SYNTAX INTEGER (0..4095) UNITS "0.01 dBm/Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOPSD-pb) Parameter defines the 'b' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. Parameter 'b' (xdsl2LConfProfUpboPsdB) ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. " DEFVAL { 0 } ::= { msanDslSpecificEntry 48 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.49 msanDslSpecificUpboUs4a OBJECT-TYPE SYNTAX INTEGER (4000..8095) UNITS "0.01 dBm/Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOPSD-pb) Parameter defines the 'a' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. A UPBO PSD defined for each band shall consist of two parameters [a, b]. Parameter 'a' (xdsl2LConfProfUpboPsdA) ranges from 40 dBm/Hz (coded as 4000) to 80.95 dBm/Hz (coded as 8095) in steps of 0.01 dBm/Hz; and parameter 'b' (xdsl2LConfProfUpboPsdB) ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency 'f' expressed in MHz shall be equal to '-a-b(SQRT(f))'. Setting xdsl2LConfProfUpboPsdA to 4000 and xdsl2LConfProfUpboPsdB to 0 is a special configuration to disable UPBO in the respective upstream band." DEFVAL { 4000 } ::= { msanDslSpecificEntry 49 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.50 msanDslSpecificUpboUs4b OBJECT-TYPE SYNTAX INTEGER (0..4095) UNITS "0.01 dBm/Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOPSD-pb) Parameter defines the 'b' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. Parameter 'b' (xdsl2LConfProfUpboPsdB) ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. " DEFVAL { 0 } ::= { msanDslSpecificEntry 50 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.51 msanDslSpecificDpboEPsdMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "DPbo EPsd mask name. It should be of the downstream PSD mask as defined by msanDslPsdMaskDsName." DEFVAL { "" } ::= { msanDslSpecificEntry 51 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.52 msanDslSpecificDpboEsCmA OBJECT-TYPE SYNTAX Unsigned32 (0..640) UNITS "2^-8" MAX-ACCESS read-create STATUS current DESCRIPTION "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOESCMA) The E-side Cable Model parameter A (DPBOESCMA) of the cable model (DPBOESCM) for cables connecting exchange-based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back- off (DPBO) depending on this value. Possible values shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in steps of 2-8 All values in the range are valid. " REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOESCMA)" DEFVAL { 0 } ::= { msanDslSpecificEntry 52 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.53 msanDslSpecificDpboEsCmB OBJECT-TYPE SYNTAX Unsigned32 (0..640) UNITS "2^-8" MAX-ACCESS read-create STATUS current DESCRIPTION "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOESCMB) The E-side Cable Model parameter B (DPBOESCMB) of the cable model (DPBOESCM) for cables connecting exchange-based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back- off (DPBO) depending on this value. Possible values shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in steps of 2-8 All values in the range are valid. " REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOESCMB)" DEFVAL { 0 } ::= { msanDslSpecificEntry 53 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.54 msanDslSpecificDpboEsCmC OBJECT-TYPE SYNTAX Unsigned32 (0..640) UNITS "2^-8" MAX-ACCESS read-create STATUS current DESCRIPTION "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOESCMC) The E-side Cable Model parameter C (DPBOESCMC) of the cable model (DPBOESCM) for cables connecting exchange-based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back- off (DPBO) depending on this value. Possible values shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in steps of 2-8 All values in the range are valid. " REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOESCMC)" DEFVAL { 0 } ::= { msanDslSpecificEntry 54 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.55 msanDslSpecificDpboMus OBJECT-TYPE SYNTAX Unsigned32 (0..255) UNITS "0.5 dBm/Hz" MAX-ACCESS read-create STATUS current DESCRIPTION "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOMUS) Assumed Minimum Usable receive PSD mask (in dBm/Hz) for exchange-based services. It shall be coded as an unsigned integer representing a PSD mask level from 0 dBm/Hz (coded as 0) to -127.5 dBm/Hz (coded as 255) in steps of 0.5 dBm/Hz. All values in the range are valid. " REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOMUS)" DEFVAL { 0 } ::= { msanDslSpecificEntry 55 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.56 msanDslSpecificDpboFMin OBJECT-TYPE SYNTAX Unsigned32 (0..2048) UNITS "4.3125 kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOFMIN) Minimum frequency from which the DPBO shall be applied. It ranges from 0 kHz (coded as 0) to 8832 kHz (coded as 2048) in steps of 4.3125 kHz. " REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOFMIN)" DEFVAL { 32 } ::= { msanDslSpecificEntry 56 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.3.1.57 msanDslSpecificDpboFMax OBJECT-TYPE SYNTAX Unsigned32 (32..6956) UNITS "4.3125 kHz" MAX-ACCESS read-create STATUS current DESCRIPTION "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOFMAX) Maximum frequency at which DPBO may be applied. It ranges from 138 kHz (coded as 32) to 29997.75 kHz (coded as 6956) in steps of 4.3125 kHz. " REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOFMAX)" DEFVAL { 512 } ::= { msanDslSpecificEntry 57 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.4 msanDslPsdMaskDsTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanDslPsdMaskDsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Management of Downstream PSD Mask (G997.1 #7.3.1.2.9 )" ::= { msanDslSpecific 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.4.1 msanDslPsdMaskDsEntry OBJECT-TYPE SYNTAX MsanDslPsdMaskDsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanDslPsdMaskDsName } ::= { msanDslPsdMaskDsTable 1 } MsanDslPsdMaskDsEntry ::= SEQUENCE { msanDslPsdMaskDsName OCTET STRING, msanDslPsdMaskDsType INTEGER, msanDslPsdMaskDsShape Xdsl2PsdMaskDs, msanDslPsdMaskDsRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.19.4.1.1 msanDslPsdMaskDsName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Downstream custom PSD mask name." ::= { msanDslPsdMaskDsEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.4.1.2 msanDslPsdMaskDsType OBJECT-TYPE SYNTAX INTEGER { default(1), configured(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Downstream custom PSD mask type. Possible values: default(1) - Default mask prepared by vendor, user is not allowed to delete or change it configured(2) - Mask created by user " DEFVAL { management } ::= { msanDslPsdMaskDsEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.4.1.3 msanDslPsdMaskDsShape OBJECT-TYPE SYNTAX Xdsl2PsdMaskDs MAX-ACCESS read-write STATUS current DESCRIPTION "The downstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G.992.5 and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a string of 32 pairs of values in the following structure: Octets 0-1 - Index of the first subcarrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the subcarrier indicated in octets 0 and 1. Octets 3-5 - Same, for a second breakpoint. Octets 6-8 - Same, for a third breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 0 and NSCds-1. Each PSD reduction value is in the range 0 (0 dBm/Hz) to 255 (-127.5 dBm/Hz) with steps of 0.5 dBm/Hz. Valid values are in the range 0 to 190 (0 to -95 dBm/Hz). When the number of breakpoints is less than 32, all remaining octets are set to the value '0'. Note that the content of this object should be correlated with the subcarrier mask and with the RFI setup. " DEFVAL { '0'h } ::= { msanDslPsdMaskDsEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.4.1.4 msanDslPsdMaskDsRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanDslPsdMaskDsEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.5 msanDslPsdMaskUsTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanDslPsdMaskUsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Management of Upstream PSD Mask (G997.1 #7.3.1.2.9 )" ::= { msanDslSpecific 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.5.1 msanDslPsdMaskUsEntry OBJECT-TYPE SYNTAX MsanDslPsdMaskUsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanDslPsdMaskUsName } ::= { msanDslPsdMaskUsTable 1 } MsanDslPsdMaskUsEntry ::= SEQUENCE { msanDslPsdMaskUsName OCTET STRING, msanDslPsdMaskUsType INTEGER, msanDslPsdMaskUsShape Xdsl2PsdMaskUs, msanDslPsdMaskUsRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.19.5.1.1 msanDslPsdMaskUsName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Upstream custom PSD mask name." ::= { msanDslPsdMaskUsEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.5.1.2 msanDslPsdMaskUsType OBJECT-TYPE SYNTAX INTEGER { default(1), configured(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Downstream custom PSD mask type. Possible values: default(1) - Default mask prepared by vendor, user is not allowed to delete or change it configured(2) - Mask created by user" DEFVAL { management } ::= { msanDslPsdMaskUsEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.5.1.3 msanDslPsdMaskUsShape OBJECT-TYPE SYNTAX Xdsl2PsdMaskUs MAX-ACCESS read-write STATUS current DESCRIPTION "The upstream PSD mask applicable at the U-R2 reference point. This parameter is used only for G.992.5, and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a string of 16 pairs of values in the following structure: Octets 0-1 - Index of the first subcarrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the subcarrier indicated in octets 0 and 1. Octets 3-5 - Same, for a second breakpoint. Octets 6-8 - Same, for a third breakpoint. This architecture continues until octets 9-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 0 and NSCus-1. Each PSD reduction value is in the range 0 (0 dBm/Hz) to 255 (-127.5 dBm/Hz) with steps of 0.5 dBm/Hz. Valid values are in the range 0 to 190 (0 to -95 dBm/Hz). When the number of breakpoints is less than 16, all remaining octets are set to the value '0'. Note that the content of this object should be correlated with the subcarrier mask and with the RFI setup. " DEFVAL { '0'h } ::= { msanDslPsdMaskUsEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.5.1.4 msanDslPsdMaskUsRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanDslPsdMaskUsEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.6 msanDslSeltStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanDslSeltStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanDslSpecific 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.6.1 msanDslSeltStatusEntry OBJECT-TYPE SYNTAX MsanDslSeltStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanDslSeltStatusTable 1 } MsanDslSeltStatusEntry ::= SEQUENCE { msanDslSeltStatusNoiseType OCTET STRING, msanDslSeltStatusNoiseMrgDs Integer32, msanDslSeltStatusNoiseMrgUs Integer32, msanDslSeltStatusNumTonesDs Integer32, msanDslSeltStatusNumTonesUs Integer32, msanDslSeltStatusMaxRateDs Integer32, msanDslSeltStatusMaxRateUs Integer32, msanDslSeltStatusCableType OCTET STRING, msanDslSeltStatusCableLenght Integer32, msanDslSeltStatusFitError Integer32, msanDslSeltStatusLoopTermination INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.19.6.1.1 msanDslSeltStatusNoiseType OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..30)) MAX-ACCESS read-only STATUS current DESCRIPTION "Noise type." ::= { msanDslSeltStatusEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.6.1.2 msanDslSeltStatusNoiseMrgDs OBJECT-TYPE SYNTAX Integer32 UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Noise margin in DS direction. [0.1 dB]" ::= { msanDslSeltStatusEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.6.1.3 msanDslSeltStatusNoiseMrgUs OBJECT-TYPE SYNTAX Integer32 UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Noise margin in US direction. [0.1 dB]" ::= { msanDslSeltStatusEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.6.1.4 msanDslSeltStatusNumTonesDs OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of tones used for SELT in DS direction. " ::= { msanDslSeltStatusEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.6.1.5 msanDslSeltStatusNumTonesUs OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of tones used for SELT in US direction. " ::= { msanDslSeltStatusEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.6.1.6 msanDslSeltStatusMaxRateDs OBJECT-TYPE SYNTAX Integer32 UNITS "kbps" MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum Downstream capacity [kbps]" ::= { msanDslSeltStatusEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.6.1.7 msanDslSeltStatusMaxRateUs OBJECT-TYPE SYNTAX Integer32 UNITS "kbps" MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum Upstream capacity [kbps]" ::= { msanDslSeltStatusEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.6.1.8 msanDslSeltStatusCableType OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "DSL line loop type." ::= { msanDslSeltStatusEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.6.1.9 msanDslSeltStatusCableLenght OBJECT-TYPE SYNTAX Integer32 UNITS "m" MAX-ACCESS read-only STATUS current DESCRIPTION "DSL line loop lenght. [m]" ::= { msanDslSeltStatusEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.6.1.10 msanDslSeltStatusFitError OBJECT-TYPE SYNTAX Integer32 UNITS "%" MAX-ACCESS read-only STATUS current DESCRIPTION "DSL Line lenght fit error. [%]" ::= { msanDslSeltStatusEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.19.6.1.11 msanDslSeltStatusLoopTermination OBJECT-TYPE SYNTAX INTEGER { unknown(1), open(2), short(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of DSL line termination. " ::= { msanDslSeltStatusEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.20 msanPortMirroring OBJECT IDENTIFIER ::= { msanAdditionalConf 20 } -- 1.3.6.1.4.1.1332.1.1.5.3.20.1 msanPortMirroringGlobal OBJECT IDENTIFIER ::= { msanPortMirroring 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.20.2 msanPortMirroringTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanPortMirroringEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanPortMirroring 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.20.2.1 msanPortMirroringEntry OBJECT-TYPE SYNTAX MsanPortMirroringEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanPortMirroringSessionId } ::= { msanPortMirroringTable 1 } MsanPortMirroringEntry ::= SEQUENCE { msanPortMirroringSessionId Integer32, msanPortMirroringAdminState INTEGER, msanPortMirroringDestPort Integer32 } -- 1.3.6.1.4.1.1332.1.1.5.3.20.2.1.1 msanPortMirroringSessionId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Session number of this mirroring entry." ::= { msanPortMirroringEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.20.2.1.2 msanPortMirroringAdminState OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "The status of this port mirroring session. " ::= { msanPortMirroringEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.20.2.1.3 msanPortMirroringDestPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The port which traffic from the mirrored ports will be sent to. Port value is ifIndex from ifTable. Value 0 means, port is not defined." ::= { msanPortMirroringEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.20.3 msanPortMirroringMemberTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanPortMirroringMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanPortMirroring 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.20.3.1 msanPortMirroringMemberEntry OBJECT-TYPE SYNTAX MsanPortMirroringMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanPortMirroringSessionId, msanPortMirroringMemberSrcPort } ::= { msanPortMirroringMemberTable 1 } MsanPortMirroringMemberEntry ::= SEQUENCE { msanPortMirroringMemberSrcPort Integer32, msanPortMirroringMemberDirection INTEGER, msanPortMirroringMemberRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.20.3.1.1 msanPortMirroringMemberSrcPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port from which traffic will be sent to the destination port. " ::= { msanPortMirroringMemberEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.20.3.1.2 msanPortMirroringMemberDirection OBJECT-TYPE SYNTAX INTEGER { tx(1), rx(2), txAndRx(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The direction of the data to be mirrored on this source port. " ::= { msanPortMirroringMemberEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.20.3.1.3 msanPortMirroringMemberRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported]." ::= { msanPortMirroringMemberEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.21 msanResetWithDelay OBJECT IDENTIFIER ::= { msanAdditionalConf 21 } -- 1.3.6.1.4.1.1332.1.1.5.3.21.1 msanResetWithDelayGlobal OBJECT IDENTIFIER ::= { msanResetWithDelay 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.21.1.1 msanResetDelay OBJECT-TYPE SYNTAX INTEGER (0..3600) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Delay in seconds before reset will be performed. If set to 0, reset countdown is stopped and reset is cancelled. This parameter returns number of seconds before reset. If it returns 0, reset with delay was not initiated. " ::= { msanResetWithDelayGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.22 msanMacTable OBJECT IDENTIFIER ::= { msanAdditionalConf 22 } -- 1.3.6.1.4.1.1332.1.1.5.3.22.1 msanMacTableGlobal OBJECT IDENTIFIER ::= { msanMacTable 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.22.1.1 msanMacTableLength OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum number of MAC addresses (total length of MAC table). " ::= { msanMacTableGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.22.1.2 msanMacTableUsed OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of entries in MAC table." ::= { msanMacTableGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.22.2 msanMacTableCAMTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMacTableCAMEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanMacTable 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.22.2.1 msanMacTableCAMEntry OBJECT-TYPE SYNTAX MsanMacTableCAMEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanMacTableCAMIndex } ::= { msanMacTableCAMTable 1 } MsanMacTableCAMEntry ::= SEQUENCE { msanMacTableCAMIndex Integer32, msanMacTableMacAddress MacAddress, msanMacTablePort Integer32, msanMacTableVLAN Integer32, msanMacTableType INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.22.2.1.1 msanMacTableCAMIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Id of the CAM entry." ::= { msanMacTableCAMEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.22.2.1.2 msanMacTableMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "MAC address of the CAM entry. " ::= { msanMacTableCAMEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.22.2.1.3 msanMacTablePort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The port on which MAC address was learned or defined. " ::= { msanMacTableCAMEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.22.2.1.4 msanMacTableVLAN OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN id of the learned or defined MAC address. " ::= { msanMacTableCAMEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.22.2.1.5 msanMacTableType OBJECT-TYPE SYNTAX INTEGER { learned(1), managment(2), static(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of the MAC address. " ::= { msanMacTableCAMEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.23 msanAcs OBJECT IDENTIFIER ::= { msanAdditionalConf 23 } -- 1.3.6.1.4.1.1332.1.1.5.3.23.1 msanAcsGlobal OBJECT IDENTIFIER ::= { msanAcs 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.23.1.1 msanAcsServerUrl OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "This is URL of the ACS server in form: http:///acs. If hostname is used, msanDnsIpAddress and msanAcsDomainName must also be set. " ::= { msanAcsGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.23.1.2 msanPrimaryDnsIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the primary DNS server IP . " ::= { msanAcsGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.23.1.3 msanSecondaryDnsIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the secondary DNS server IP . " ::= { msanAcsGlobal 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.23.1.4 msanAcsDomainName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Domain name. " ::= { msanAcsGlobal 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.23.1.5 msanAcsClientStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "ACS client administrative status." ::= { msanAcsGlobal 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.23.1.6 msanAcsBackupConf OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Back up configuration (as CLI script) to ACS server." ::= { msanAcsGlobal 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.24 msanStp OBJECT IDENTIFIER ::= { msanAdditionalConf 24 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.1 msanStpGlobal OBJECT IDENTIFIER ::= { msanStp 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.2 msanStpBpduFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanStpBpduFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanStp 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.2.1 msanStpBpduFilterEntry OBJECT-TYPE SYNTAX MsanStpBpduFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanStpBpduFilterTable 1 } MsanStpBpduFilterEntry ::= SEQUENCE { msanStpBpduFilter INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.24.2.1.1 msanStpBpduFilter OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Defines how BPDU packets are handled in case stp_port_state is disabled. 0 disable - If stp_port_state is disabled on interface, forward all BPDUs unchanged to all other interfaces that also have stp_port_state disabled. 1 enable - If stp_port_state is disabled on interface, drop all BPDUs received on the interface. " ::= { msanStpBpduFilterEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.3 msanStpSwitchConfigGroup OBJECT IDENTIFIER ::= { msanStp 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.3.1 msanStpCstBridgePriority OBJECT-TYPE SYNTAX Unsigned32 (0..61440) MAX-ACCESS read-write STATUS current DESCRIPTION "The CSTP bridge priority in instance 0. The priority is in the increments of 4096. The recommended default value is 32768." ::= { msanStpSwitchConfigGroup 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.4 msanStpMstTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanStpMstEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." REFERENCE "agentStpMstTable - 1.3.6.1.4.1.6132.1.1.1.2.15.10" ::= { msanStp 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.4.1 msanStpMstEntry OBJECT-TYPE SYNTAX MsanStpMstEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanStpMstId } ::= { msanStpMstTable 1 } MsanStpMstEntry ::= SEQUENCE { msanStpMstId Unsigned32, msanStpMstBridgePriority Unsigned32, msanStpMstRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.24.4.1.1 msanStpMstId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MSTP instance ID. Instance 0 is not shown. " ::= { msanStpMstEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.4.1.2 msanStpMstBridgePriority OBJECT-TYPE SYNTAX Unsigned32 (0..61440) MAX-ACCESS read-create STATUS current DESCRIPTION "The MSTP bridge priority in a specific instance. The priority is in the increments of 4096. The recommended default value is 32768." ::= { msanStpMstEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.4.1.3 msanStpMstRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The MSTP instance status. Instance 0 is not shown. Supported values: active(1) - valid instance. createAndGo(4) - used to create a new instance. destroy(6) - removes an instance." ::= { msanStpMstEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.5 msanStpMstVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanStpMstVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." REFERENCE "agentStpMstTable - 1.3.6.1.4.1.6132.1.1.1.2.15.10" ::= { msanStp 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.5.1 msanStpMstVlanEntry OBJECT-TYPE SYNTAX MsanStpMstVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { dot1qVlanIndex, msanStpMstId } ::= { msanStpMstVlanTable 1 } MsanStpMstVlanEntry ::= SEQUENCE { msanStpMstVlanRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.24.5.1.1 msanStpMstVlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The association status of an MSTP instance and a VLAN. Instance 0 is not shown. Supported values: active(1) - valid association between an MSTP instance and a VLAN. createAndGo(4) - used to create a new association between an MSTP instance and a VLAN. destroy(6) - removes the association between an MSTP instance and a VLAN." ::= { msanStpMstVlanEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.6 msanStpMstPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanStpMstPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "MST port table." REFERENCE "agentStpMstPortTable - 1.3.6.1.4.1.6132.1.1.1.2.15.11" ::= { msanStp 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.6.1 msanStpMstPortEntry OBJECT-TYPE SYNTAX MsanStpMstPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "MST port entry." INDEX { ifIndex, msanStpMstId } ::= { msanStpMstPortTable 1 } MsanStpMstPortEntry ::= SEQUENCE { msanStpMstPortPathCost Unsigned32, msanStpMstPortPriority Unsigned32 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.6.1.1 msanStpMstPortPathCost OBJECT-TYPE SYNTAX Unsigned32 (0..200000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The MSTP port path cost in a specific instance. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed. Instance 0 is not shown." ::= { msanStpMstPortEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.6.1.2 msanStpMstPortPriority OBJECT-TYPE SYNTAX Unsigned32 (0..240) MAX-ACCESS read-write STATUS current DESCRIPTION "The MSTP port priority in a specific instance. The priority is in the increments of 16. The default value is 128. Instance 0 is not shown." DEFVAL { 128 } ::= { msanStpMstPortEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.7 msanStpPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanStpPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanStp 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.7.1 msanStpPortEntry OBJECT-TYPE SYNTAX MsanStpPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanStpPortTable 1 } MsanStpPortEntry ::= SEQUENCE { msanStpPortHelloTime Integer32 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.7.1.1 msanStpPortHelloTime OBJECT-TYPE SYNTAX Integer32 (0..10) MAX-ACCESS read-write STATUS current DESCRIPTION "Hello time for the STP port. The default value is 0 (Not configured)." ::= { msanStpPortEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.8 msanStpCstPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanStpCstPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanStp 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.8.1 msanStpCstPortEntry OBJECT-TYPE SYNTAX MsanStpCstPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanStpCstPortTable 1 } MsanStpCstPortEntry ::= SEQUENCE { msanStpCstPortPathCost Unsigned32, msanStpCstExtPortPathCost Unsigned32 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.8.1.1 msanStpCstPortPathCost OBJECT-TYPE SYNTAX Unsigned32 (0..200000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The MSTP port path cost in CIST. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed. " ::= { msanStpCstPortEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.24.8.1.2 msanStpCstExtPortPathCost OBJECT-TYPE SYNTAX Unsigned32 (0..200000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The MSTP external port path cost in CIST. The default value varies depending upon the link speed." ::= { msanStpCstPortEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.25 msanAuthentication OBJECT IDENTIFIER ::= { msanAdditionalConf 25 } -- 1.3.6.1.4.1.1332.1.1.5.3.25.1 msanAuthenticationGlobal OBJECT IDENTIFIER ::= { msanAuthentication 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.25.2 msanAuthenticationListCreate OBJECT-TYPE SYNTAX DisplayString (SIZE (1..15)) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Authentication List Create If set to a non empty string, creates a new Authentication List for configuration." ::= { msanAuthentication 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.25.3 msanAuthenticationListTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanAuthenticationListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanAuthentication 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.25.3.1 msanAuthenticationListEntry OBJECT-TYPE SYNTAX MsanAuthenticationListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanAuthenticationListName } ::= { msanAuthenticationListTable 1 } MsanAuthenticationListEntry ::= SEQUENCE { msanAuthenticationListName DisplayString, msanAuthenticationListMethod1 INTEGER, msanAuthenticationListMethod2 INTEGER, msanAuthenticationListMethod3 INTEGER, msanAuthenticationListStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.25.3.1.1 msanAuthenticationListName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..15)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Authenticaiton List Name Unique name used to identify the Authentication List from other tables." ::= { msanAuthenticationListEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.25.3.1.2 msanAuthenticationListMethod1 OBJECT-TYPE SYNTAX INTEGER { local(1), radius(2), reject(3), tacacs(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Authenticion List Method 1 Configures the first authentication method to use when this list is specified." ::= { msanAuthenticationListEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.25.3.1.3 msanAuthenticationListMethod2 OBJECT-TYPE SYNTAX INTEGER { undefined(1), local(2), radius(3), reject(4), tacacs(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "Authenticion List Method 2 Configures the second authentication method to use when this list is specified." ::= { msanAuthenticationListEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.25.3.1.4 msanAuthenticationListMethod3 OBJECT-TYPE SYNTAX INTEGER { undefined(1), local(2), radius(3), reject(4), tacacs(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "Authenticion List Method 3 Configures the third authentication method to use when this list is specified." ::= { msanAuthenticationListEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.25.3.1.5 msanAuthenticationListStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of the Authentication List. Supported values: active(1) - indicates a valid Authenticaiton List createAndGo (4) destroy(6) - removes the Authentication List." ::= { msanAuthenticationListEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.26 msanPortSecurity OBJECT IDENTIFIER ::= { msanAdditionalConf 26 } -- 1.3.6.1.4.1.1332.1.1.5.3.26.1 msanPortSecurityGlobal OBJECT IDENTIFIER ::= { msanPortSecurity 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.26.2 msanPortSecurityStatMacTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanPortSecurityStatMacEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanPortSecurity 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.26.2.1 msanPortSecurityStatMacEntry OBJECT-TYPE SYNTAX MsanPortSecurityStatMacEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanPortSecurityStatMacIf, msanPortSecurityStatMacVlanId, msanPortSecurityStatMacMacAddress } ::= { msanPortSecurityStatMacTable 1 } MsanPortSecurityStatMacEntry ::= SEQUENCE { msanPortSecurityStatMacIf Integer32, msanPortSecurityStatMacVlanId INTEGER, msanPortSecurityStatMacMacAddress MacAddress, msanPortSecurityStatMacRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.26.2.1.1 msanPortSecurityStatMacIf OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Unique numerical identification of the interface." ::= { msanPortSecurityStatMacEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.26.2.1.2 msanPortSecurityStatMacVlanId OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS not-accessible STATUS current DESCRIPTION "VLAN identification." ::= { msanPortSecurityStatMacEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.26.2.1.3 msanPortSecurityStatMacMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Statically locked MAC addresses for port." ::= { msanPortSecurityStatMacEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.26.2.1.5 msanPortSecurityStatMacRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanPortSecurityStatMacEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.26.3 msanPortSecurityPortVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanPortSecurityPortVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanPortSecurity 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.26.3.1 msanPortSecurityPortVlanEntry OBJECT-TYPE SYNTAX MsanPortSecurityPortVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex, dot1qVlanIndex } ::= { msanPortSecurityPortVlanTable 1 } MsanPortSecurityPortVlanEntry ::= SEQUENCE { msanPortSecurityPortVlanDynamicLimit Integer32, msanPortSecurityPortVlanRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.26.3.1.1 msanPortSecurityPortVlanDynamicLimit OBJECT-TYPE SYNTAX Integer32 (1..64) MAX-ACCESS read-write STATUS current DESCRIPTION "The limit of dynamically learned MAC addresses per vlan on selected port. " ::= { msanPortSecurityPortVlanEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.26.3.1.2 msanPortSecurityPortVlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported." ::= { msanPortSecurityPortVlanEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.27 msanLag OBJECT IDENTIFIER ::= { msanAdditionalConf 27 } -- 1.3.6.1.4.1.1332.1.1.5.3.27.1 msanLagGlobal OBJECT IDENTIFIER ::= { msanLag 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.27.2 msanLagDetailedConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanLagDetailedConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A detailed table of the switch's LAG config entries. " REFERENCE "agentLagDetailedConfigTable" ::= { msanLag 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.27.2.1 msanLagDetailedConfigEntry OBJECT-TYPE SYNTAX MsanLagDetailedConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Switch's LAG config entry" INDEX { msanLagDetailedLagIndex, msanLagDetailedIfIndex } ::= { msanLagDetailedConfigTable 1 } MsanLagDetailedConfigEntry ::= SEQUENCE { msanLagDetailedLagIndex Integer32, msanLagDetailedIfIndex Integer32, msanLagDetailedPortSpeed OBJECT IDENTIFIER, msanLagDetailedPortStatus INTEGER, msanLagDetailedRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.27.2.1.1 msanLagDetailedLagIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "LAG index" ::= { msanLagDetailedConfigEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.27.2.1.2 msanLagDetailedIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "LAG port index" ::= { msanLagDetailedConfigEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.27.2.1.3 msanLagDetailedPortSpeed OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "LAG port speed. See agentPortType for a description and list of valid values." ::= { msanLagDetailedConfigEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.27.2.1.4 msanLagDetailedPortStatus OBJECT-TYPE SYNTAX INTEGER { active(1), inactive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "LAG port status. active(1) - Actively participating in the LAG. inactive(2) - Not participating in the LAG." ::= { msanLagDetailedConfigEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.27.2.1.5 msanLagDetailedRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanLagDetailedConfigEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.27.3 msanLagTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanLagEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Config table of additional LAG parameters." ::= { msanLag 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.27.3.1 msanLagEntry OBJECT-TYPE SYNTAX MsanLagEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanLagIndex } ::= { msanLagTable 1 } MsanLagEntry ::= SEQUENCE { msanLagIndex Integer32, msanLagMaxFrameSize Integer32, msanLagDVlanTagMode INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.27.3.1.1 msanLagIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "LAG index. Value corresponds to ifIndex for LAG interfaces in ifTable." ::= { msanLagEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.27.3.1.2 msanLagMaxFrameSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object identifies the currently configured maximum frame size value for this LAG interface. " ::= { msanLagEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.27.3.1.3 msanLagDVlanTagMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Controls the Double Vlan Tag mode on this LAG interface." ::= { msanLagEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.28 msanRadiusServer OBJECT IDENTIFIER ::= { msanAdditionalConf 28 } -- 1.3.6.1.4.1.1332.1.1.5.3.28.1 msanRadiusServerGlobal OBJECT IDENTIFIER ::= { msanRadiusServer 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.28.2 msanRadiusServerConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanRadiusServerConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table with information about Radius Authentication Server IP Addresses, port numbers and shared secret" ::= { msanRadiusServer 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.28.2.1 msanRadiusServerConfigEntry OBJECT-TYPE SYNTAX MsanRadiusServerConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry consisting of configuration data for a Radius Authentication Server." INDEX { msanRadiusServerAddress } ::= { msanRadiusServerConfigTable 1 } MsanRadiusServerConfigEntry ::= SEQUENCE { msanRadiusServerAddress IpAddress, msanRadiusServerPort Unsigned32, msanRadiusServerSecret DisplayString, msanRadiusServerPrimaryMode INTEGER, msanRadiusServerCurrentMode INTEGER, msanRadiusServerMsgAuth INTEGER, msanRadiusServerStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.28.2.1.1 msanRadiusServerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "IP Address of the configured RADIUS server. This object cannot be changed after creation." ::= { msanRadiusServerConfigEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.28.2.1.2 msanRadiusServerPort OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Port number for the RADIUS server." DEFVAL { 1812 } ::= { msanRadiusServerConfigEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.28.2.1.3 msanRadiusServerSecret OBJECT-TYPE SYNTAX DisplayString (SIZE (0..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "Configured shared sercret for the RADIUS server." ::= { msanRadiusServerConfigEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.28.2.1.4 msanRadiusServerPrimaryMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configure the RADIUS server to be the primary server. If there is any other server that is configured to be primary, that server is set to be a seconday server and this entry is set Primary." ::= { msanRadiusServerConfigEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.28.2.1.5 msanRadiusServerCurrentMode OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate if the RADIUS server is the current server in user for authentication." ::= { msanRadiusServerConfigEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.28.2.1.6 msanRadiusServerMsgAuth OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable the message authenticator attribute for this RADIUS server." ::= { msanRadiusServerConfigEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.28.2.1.7 msanRadiusServerStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Creates or destroys a RADIUS Authentication server entry. active(1) - This entry is active. createAndGo(4) - Creates a new entry. destroy(6) - Deletes an entry." ::= { msanRadiusServerConfigEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.29 msanNetwork OBJECT IDENTIFIER ::= { msanAdditionalConf 29 } -- 1.3.6.1.4.1.1332.1.1.5.3.29.1 msanNetworkGlobal OBJECT IDENTIFIER ::= { msanNetwork 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.29.1.1 msanNetworkIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's network ip address" ::= { msanNetworkGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.29.1.2 msanNetworkSubnetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's network subnet mask" ::= { msanNetworkGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.29.1.3 msanNetworkDefaultGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The switch's network default gateway" ::= { msanNetworkGlobal 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.29.1.4 msanNetworkDhcpSrvIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "IP address of DHCP server used by DHCP client." ::= { msanNetworkGlobal 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.29.1.5 msanNetworkDhcpSrvVendorSpecific OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "DHCP client uses only vendor specific DHCP servers (when client sends opt. 60 to server, it should return expected vendor specific value in opt. 43)" ::= { msanNetworkGlobal 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.29.1.6 msanNetworkDhcpClientLeaseObtained OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The date and time when DHCP lease was obtained. " ::= { msanNetworkGlobal 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.29.1.7 msanNetworkDhcpClientLeaseExpires OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The date and time for which the DHCP lease is valid." ::= { msanNetworkGlobal 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.29.1.8 msanNetworkDhcpClientLocalOpt82 OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "DHCP client adds relay agent information option into its own outgoing frames." ::= { msanNetworkGlobal 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.29.2 msanNetworkDhcpClientVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanNetworkDhcpClientVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "DHCP client configuration per vlan id." ::= { msanNetwork 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.29.2.1 msanNetworkDhcpClientVlanEntry OBJECT-TYPE SYNTAX MsanNetworkDhcpClientVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { dot1qVlanIndex } ::= { msanNetworkDhcpClientVlanTable 1 } MsanNetworkDhcpClientVlanEntry ::= SEQUENCE { msanNetworkDhcpClientVlanLocalOpt82 INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.29.2.1.1 msanNetworkDhcpClientVlanLocalOpt82 OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "DHCP client on specified vlan adds relay agent information option into its own outgoing frames." DEFVAL { disable } ::= { msanNetworkDhcpClientVlanEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.30 msanStormControl OBJECT IDENTIFIER ::= { msanAdditionalConf 30 } -- 1.3.6.1.4.1.1332.1.1.5.3.30.1 msanStormControlGlobal OBJECT IDENTIFIER ::= { msanStormControl 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.30.2 msanPortStormControlTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanPortStormControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanStormControl 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.30.2.1 msanPortStormControlEntry OBJECT-TYPE SYNTAX MsanPortStormControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanPortStormControlTable 1 } MsanPortStormControlEntry ::= SEQUENCE { msanPortBroadcastControlMode INTEGER, msanPortBroadcastControlThreshold Integer32, msanPortMulticastControlMode INTEGER, msanPortMulticastControlThreshold Integer32, msanPortUnicastControlMode INTEGER, msanPortUnicastControlThreshold Integer32 } -- 1.3.6.1.4.1.1332.1.1.5.3.30.2.1.1 msanPortBroadcastControlMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "he switch config broadcast allows you to enable or disable broadcast storm recovery mode. When you specify Enable for Broadcast Storm Recovery and the broadcast traffic on any Ethernet port exceeds the configured threshold, the switch blocks (discards) the broadcast traffic. " ::= { msanPortStormControlEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.30.2.1.2 msanPortBroadcastControlThreshold OBJECT-TYPE SYNTAX Integer32 UNITS "packets per second" MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the data rate at which broadcast storm control activates (packets per second)" ::= { msanPortStormControlEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.30.2.1.3 msanPortMulticastControlMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch config multicast allows you to enable or disable multicast storm recovery mode. When you specify Enable for multicast Storm Recovery and the multicast traffic on any Ethernet port exceeds the configured threshold, the switch blocks (discards) the multicast traffic" ::= { msanPortStormControlEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.30.2.1.4 msanPortMulticastControlThreshold OBJECT-TYPE SYNTAX Integer32 UNITS "packets per second" MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the data rate at which multicast storm control activates (packets per second)" ::= { msanPortStormControlEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.30.2.1.5 msanPortUnicastControlMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The switch config unicast allows you to enable or disable unicast storm recovery mode. When you specify Enable for unicast Storm Recovery and the unknown unicast traffic on any Ethernet port exceeds the configured threshold, the switch blocks (discards) the unknown unicast traffic. " ::= { msanPortStormControlEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.30.2.1.6 msanPortUnicastControlThreshold OBJECT-TYPE SYNTAX Integer32 UNITS "packets per second" MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the data rate at which unicast storm control activates (packets per second)" ::= { msanPortStormControlEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.31 msanUserConfig OBJECT IDENTIFIER ::= { msanAdditionalConf 31 } -- 1.3.6.1.4.1.1332.1.1.5.3.31.1 msanUserConfigGlobal OBJECT IDENTIFIER ::= { msanUserConfig 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.31.1.1 msanUserConfigCheckPassword OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter is used to check user's password. String must be written in next format: user_name password First blank space is used as delimeter between user_name and password. If password is not valid or user is not configured, inconsistentValue(12)error code will be returned. " ::= { msanUserConfigGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.31.2 msanUserConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanUserConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanUserConfig 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.31.2.1 msanUserConfigEntry OBJECT-TYPE SYNTAX MsanUserConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanUserIndex } ::= { msanUserConfigTable 1 } MsanUserConfigEntry ::= SEQUENCE { msanUserIndex Integer32, msanUserAccessMode INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.31.2.1.1 msanUserIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "User Config Index" ::= { msanUserConfigEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.31.2.1.2 msanUserAccessMode OBJECT-TYPE SYNTAX INTEGER { read(1), write(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "User Access Mode" ::= { msanUserConfigEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.32 msanSfp OBJECT IDENTIFIER ::= { msanAdditionalConf 32 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.1 msanSfpGlobal OBJECT IDENTIFIER ::= { msanSfp 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.2 msanSfpInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanSfpInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanSfp 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.2.1 msanSfpInfoEntry OBJECT-TYPE SYNTAX MsanSfpInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanSfpInfoTable 1 } MsanSfpInfoEntry ::= SEQUENCE { msanSfpInfoState INTEGER, msanSfpInfoInterfaceType INTEGER, msanSfpInfoNominalBitrate Integer32, msanSfpInfoNominalRange OCTET STRING, msanSfpInfoVendor OCTET STRING, msanSfpInfoIeeeVendorId Integer32, msanSfpInfoPartNr OCTET STRING, msanSfpInfoRevisionNr OCTET STRING, msanSfpInfoSerialNr OCTET STRING, msanSfpInfoManufacturingDate OCTET STRING, msanSfpInfoWavelength Integer32 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.2.1.1 msanSfpInfoState OBJECT-TYPE SYNTAX INTEGER { adminOff(1), operational(2), operWithAl(3), loss(4), notAvaliable(5), presNoDiag(6), notPresent(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Module state value on port. Ports which support SFP module are from 1 to 10 and from 15 to 28. State value adminOff means that specific port is administrative disabled and we can not read data from module on that port. Operational state means that SFP module is present and it works perfect. State operWithAl(operational with alarm) means that SFP module is present, but it works with internal alarms. Loss(Loss of signal) state means that SFP module is present but it have loss of signal. PresNoDiag(Present, no diagnostic) state means that SFP module is present but diagnostic is not supported. NotAvaliable state means that admin. mode of specific port has disabled value and SFP state is not avaliable. NotPresent state means that SFP module is not present. " ::= { msanSfpInfoEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.2.1.2 msanSfpInfoInterfaceType OBJECT-TYPE SYNTAX INTEGER { sfp(1), not(2), no(3), ad(4), xfp(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Transceiver(module) type. Module type can be SFP, NOT(mudule type is not SFP), NO(no module on port), AD(admin. disabled port) and XFP." ::= { msanSfpInfoEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.2.1.3 msanSfpInfoNominalBitrate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Module(SFP) nominal bitrate value measure in Mbit/s. If parameter is not available, value -1 is used." ::= { msanSfpInfoEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.2.1.4 msanSfpInfoNominalRange OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Module(SFP) nominal range value. Nominal range value can support five different link lengths. Link length value and nominal range units are defined depends on value of nominal range. We can get link length value which can support 9/125 um fiber and nominal range measure in km units. We can get link length value which can support 9/125 um fiber and nominal range measure in 100m units. We can get link length value which can support 50/125 um fiber and nominal range measure in 10m units. We can get link length value which can support 62,5/125 um fiber and nominal range measure in 10m units. We can get link length value which can support cooper and nominal range measure in m units. " ::= { msanSfpInfoEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.2.1.5 msanSfpInfoVendor OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Module(SFP) vendor name." ::= { msanSfpInfoEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.2.1.6 msanSfpInfoIeeeVendorId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Module(SFP) vendor IEEE company ID. If parameter is not available, value -1 is used." ::= { msanSfpInfoEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.2.1.7 msanSfpInfoPartNr OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Module(SFP) part number." ::= { msanSfpInfoEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.2.1.8 msanSfpInfoRevisionNr OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Module(SFP) revision number." ::= { msanSfpInfoEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.2.1.9 msanSfpInfoSerialNr OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Module(SFP) serial number." ::= { msanSfpInfoEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.2.1.10 msanSfpInfoManufacturingDate OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Module(SFP) manufacturing date." ::= { msanSfpInfoEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.2.1.11 msanSfpInfoWavelength OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Module(SFP) laser wavelength measure in nanometers. If parameter is not available, value -1 is used." ::= { msanSfpInfoEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3 msanSfpDiagnosticsTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanSfpDiagnosticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanSfp 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1 msanSfpDiagnosticsEntry OBJECT-TYPE SYNTAX MsanSfpDiagnosticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanSfpDiagnosticsTable 1 } MsanSfpDiagnosticsEntry ::= SEQUENCE { msanSfpDiagnosticsSignal INTEGER, msanSfpDiagnosticsTempCurrent Integer32, msanSfpDiagnosticsTempMin Integer32, msanSfpDiagnosticsTempMax Integer32, msanSfpDiagnosticsVoltageCurrent Integer32, msanSfpDiagnosticsVoltageMin Integer32, msanSfpDiagnosticsVoltageMax Integer32, msanSfpDiagnosticsTxBiasCrrCurrent Integer32, msanSfpDiagnosticsTxBiasCrrMin Integer32, msanSfpDiagnosticsTxBiasCrrMax Integer32, msanSfpDiagnosticsTxPowerCurrent Integer32, msanSfpDiagnosticsTxPowerMin Integer32, msanSfpDiagnosticsTxPowerMax Integer32, msanSfpDiagnosticsRxPowerCurrent Integer32, msanSfpDiagnosticsRxPowerMin Integer32, msanSfpDiagnosticsRxPowerMax Integer32, msanSfpDiagnosticsTempStatus INTEGER, msanSfpDiagnosticsVoltageStatus INTEGER, msanSfpDiagnosticsTxBiasStatus INTEGER, msanSfpDiagnosticsTxPowerStatus INTEGER, msanSfpDiagnosticsRxPowerStatus INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.1 msanSfpDiagnosticsSignal OBJECT-TYPE SYNTAX INTEGER { loss(1), ok(2), notSupported(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Module(SFP) signal value. If diagnostic for SFP module is supported than value can be OK(signal is ok) or loss(loss of signal), in the other case the value is set on notSupported becouse diagnostic is not supported(-1)." ::= { msanSfpDiagnosticsEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.2 msanSfpDiagnosticsTempCurrent OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current SFP module temperature value in [deg C]. If diagnostic is not supported for SFP module then current temperature is set on not supported value(-129). " ::= { msanSfpDiagnosticsEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.3 msanSfpDiagnosticsTempMin OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "SFP module minimum temperature threshold limit in [deg C]. If diagnostic is not supported for SFP module then minimum temperature threshold limit is set on not supported value(-129). " ::= { msanSfpDiagnosticsEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.4 msanSfpDiagnosticsTempMax OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "SFP module maximum temperature threshold limit in [deg C]. If diagnostic is not supported for SFP module then maximum temperature threshold limit is set on not supported value(-129). " ::= { msanSfpDiagnosticsEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.6 msanSfpDiagnosticsVoltageCurrent OBJECT-TYPE SYNTAX Integer32 UNITS "0.01 V" MAX-ACCESS read-only STATUS current DESCRIPTION "Current SFP module supply voltage value in [V]. If diagnostic is not supported for SFP module then current supply voltage is set on not supported value(-1). " ::= { msanSfpDiagnosticsEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.7 msanSfpDiagnosticsVoltageMin OBJECT-TYPE SYNTAX Integer32 UNITS "0.01 V" MAX-ACCESS read-only STATUS current DESCRIPTION "SFP module minimum supply voltage threshold limit in [V]. If diagnostic is not supported for SFP module then minimum supply voltage threshold limit is set on not supported value(-1). " ::= { msanSfpDiagnosticsEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.8 msanSfpDiagnosticsVoltageMax OBJECT-TYPE SYNTAX Integer32 UNITS "0.01 V" MAX-ACCESS read-only STATUS current DESCRIPTION "SFP module maximum supply voltage threshold limit in [V]. If diagnostic is not supported for SFP module then maximum supply voltage threshold limit is set on not supported value(-1). " ::= { msanSfpDiagnosticsEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.9 msanSfpDiagnosticsTxBiasCrrCurrent OBJECT-TYPE SYNTAX Integer32 UNITS "0.01 mA" MAX-ACCESS read-only STATUS current DESCRIPTION "Current SFP module Tx Bias Current value in [mA]. If diagnostic is not supported for SFP module then current Tx Bias Current is set on not supported value(-1). " ::= { msanSfpDiagnosticsEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.10 msanSfpDiagnosticsTxBiasCrrMin OBJECT-TYPE SYNTAX Integer32 UNITS "0.01 mA" MAX-ACCESS read-only STATUS current DESCRIPTION "SFP module minimum Tx Bias Current threshold limit in [mA]. If diagnostic is not supported for SFP module then minimum Tx Bias Current threshold limit is set on not supported value(-1). " ::= { msanSfpDiagnosticsEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.11 msanSfpDiagnosticsTxBiasCrrMax OBJECT-TYPE SYNTAX Integer32 UNITS "0.01 mA" MAX-ACCESS read-only STATUS current DESCRIPTION "SFP module maximum Tx Bias Current threshold limit in [mA]. If diagnostic is not supported for SFP module then maximum Tx Bias Current threshold limit is set on not supported value(-1). " ::= { msanSfpDiagnosticsEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.12 msanSfpDiagnosticsTxPowerCurrent OBJECT-TYPE SYNTAX Integer32 UNITS "0.01 mW" MAX-ACCESS read-only STATUS current DESCRIPTION "Current SFP module transmitted optical output power value in [mW]. If diagnostic is not supported for SFP module then current transmitted optical output power is set on not supported value(-1). " ::= { msanSfpDiagnosticsEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.13 msanSfpDiagnosticsTxPowerMin OBJECT-TYPE SYNTAX Integer32 UNITS "0.01 mW" MAX-ACCESS read-only STATUS current DESCRIPTION "SFP module minimum transmitted optical output power threshold limit in [mW]. If diagnostic is not supported for SFP module then minimum transmitted optical output power is set on not supported value(-1). " ::= { msanSfpDiagnosticsEntry 13 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.14 msanSfpDiagnosticsTxPowerMax OBJECT-TYPE SYNTAX Integer32 UNITS "0.01 mW" MAX-ACCESS read-only STATUS current DESCRIPTION "SFP module maximum transmitted optical output power threshold limit in [mW]. If diagnostic is not supported for SFP module then maximum transmitted optical output power is set on not supported value(-1)." ::= { msanSfpDiagnosticsEntry 14 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.15 msanSfpDiagnosticsRxPowerCurrent OBJECT-TYPE SYNTAX Integer32 UNITS "0.0001 mW" MAX-ACCESS read-only STATUS current DESCRIPTION "Current SFP module received optical input power value in [mW]. If diagnostic is not supported for SFP module then current received optical input power is set on not supported value(-1). " ::= { msanSfpDiagnosticsEntry 15 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.16 msanSfpDiagnosticsRxPowerMin OBJECT-TYPE SYNTAX Integer32 UNITS "0.0001 mW" MAX-ACCESS read-only STATUS current DESCRIPTION "SFP module minimum received optical input power threshold limit in [mW]. If diagnostic is not supported for SFP module then minimum received optical input power is set on not supported value(-1). " ::= { msanSfpDiagnosticsEntry 16 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.17 msanSfpDiagnosticsRxPowerMax OBJECT-TYPE SYNTAX Integer32 UNITS "0.0001 mW" MAX-ACCESS read-only STATUS current DESCRIPTION "SFP module maximum received optical input power threshold limit in [mW]. If diagnostic is not supported for SFP module then maximum received optical input power is set on not supported value(-1). " ::= { msanSfpDiagnosticsEntry 17 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.19 msanSfpDiagnosticsTempStatus OBJECT-TYPE SYNTAX INTEGER { sfpDiagNoAlarm(1), sfpDiagAlarm(2), notAvailable(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Temperature alarm status. " ::= { msanSfpDiagnosticsEntry 19 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.20 msanSfpDiagnosticsVoltageStatus OBJECT-TYPE SYNTAX INTEGER { sfpDiagNoAlarm(1), sfpDiagAlarm(2), notAvailable(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Voltage alarm status." ::= { msanSfpDiagnosticsEntry 20 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.21 msanSfpDiagnosticsTxBiasStatus OBJECT-TYPE SYNTAX INTEGER { sfpDiagNoAlarm(1), sfpDiagAlarm(2), notAvailable(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "TX bias alarm status." ::= { msanSfpDiagnosticsEntry 21 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.22 msanSfpDiagnosticsTxPowerStatus OBJECT-TYPE SYNTAX INTEGER { sfpDiagNoAlarm(1), sfpDiagAlarm(2), notAvailable(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "TX power alarm status." ::= { msanSfpDiagnosticsEntry 22 } -- 1.3.6.1.4.1.1332.1.1.5.3.32.3.1.23 msanSfpDiagnosticsRxPowerStatus OBJECT-TYPE SYNTAX INTEGER { sfpDiagNoAlarm(1), sfpDiagAlarm(2), notAvailable(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "RX power alarm status." ::= { msanSfpDiagnosticsEntry 23 } -- 1.3.6.1.4.1.1332.1.1.5.3.34 msanMacSg OBJECT IDENTIFIER ::= { msanAdditionalConf 34 } -- 1.3.6.1.4.1.1332.1.1.5.3.34.1 msanMacSgGlobal OBJECT IDENTIFIER ::= { msanMacSg 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.34.1.1 msanMacSgStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administrative state of MAC Source Guard on the system." ::= { msanMacSgGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.34.2 msanMacSgPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMacSgPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanMacSg 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.34.2.1 msanMacSgPortEntry OBJECT-TYPE SYNTAX MsanMacSgPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanMacSgPortTable 1 } MsanMacSgPortEntry ::= SEQUENCE { msanMacSgPortStatus INTEGER, msanMacSgPortViolationsCounter Integer32 } -- 1.3.6.1.4.1.1332.1.1.5.3.34.2.1.1 msanMacSgPortStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administrative state of MAC Source Guard on interface." ::= { msanMacSgPortEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.34.2.1.2 msanMacSgPortViolationsCounter OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "MAC Source Guard Violations counter" ::= { msanMacSgPortEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.35 msanErrorDisable OBJECT IDENTIFIER ::= { msanAdditionalConf 35 } -- 1.3.6.1.4.1.1332.1.1.5.3.35.1 msanErrorDisableGlobal OBJECT IDENTIFIER ::= { msanErrorDisable 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.35.1.1 msanErrorDisableInterval OBJECT-TYPE SYNTAX Integer32 UNITS "minutes" MAX-ACCESS read-write STATUS current DESCRIPTION "The interval in minutes that will pass since error-disabled interface will be enabled. This parameter has effect only if ErrorDisable Recovery is enabled. " ::= { msanErrorDisableGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.35.1.2 msanErrorDisableMacSgDetectionStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administrative state of ErrorDisable Detection for MAC Source Guard cause. If enabled, interface will be error-disabled when MAC Source Guard violation is detected. " ::= { msanErrorDisableGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.35.1.3 msanErrorDisableMacSgRecoveryStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administrative state of ErrorDisable Recovery for MAC Source Guard cause. If enabled, interface will be automatically recovered when error-disabled due to MAC Source Guard violation." ::= { msanErrorDisableGlobal 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.35.2 msanErrorDisablePortTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanErrorDisablePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanErrorDisable 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.35.2.1 msanErrorDisablePortEntry OBJECT-TYPE SYNTAX MsanErrorDisablePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanErrorDisablePortTable 1 } MsanErrorDisablePortEntry ::= SEQUENCE { msanErrorDisablePortStatus INTEGER, msanErrorDisablePortCause OCTET STRING, msanErrorDisablePortTimeLeft Integer32, msanErrorDisablePortCounter Integer32 } -- 1.3.6.1.4.1.1332.1.1.5.3.35.2.1.1 msanErrorDisablePortStatus OBJECT-TYPE SYNTAX INTEGER { regular(1), errorDisable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter shows which interfaces are in errorDisable(2) recovery administrative state." ::= { msanErrorDisablePortEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.35.2.1.2 msanErrorDisablePortCause OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Cause for errorDisable(2) status on interface." ::= { msanErrorDisablePortEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.35.2.1.3 msanErrorDisablePortTimeLeft OBJECT-TYPE SYNTAX Integer32 UNITS "sec" MAX-ACCESS read-only STATUS current DESCRIPTION "Time in seconds which defines how much time left for interface to stay in errorDisable(2) state." ::= { msanErrorDisablePortEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.35.2.1.4 msanErrorDisablePortCounter OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the specified interface has been in errorDisable(2) state." ::= { msanErrorDisablePortEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.36 msanAdsl OBJECT IDENTIFIER ::= { msanAdditionalConf 36 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.1 msanAdslGlobal OBJECT IDENTIFIER ::= { msanAdsl 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2 msanAdslAtucPhysExtnTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanAdslAtucPhysExtnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC. This table is an extention to adslAtucPhysTable defined in rfc-2662." ::= { msanAdsl 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1 msanAdslAtucPhysExtnEntry OBJECT-TYPE SYNTAX MsanAdslAtucPhysExtnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the msanAdslAtucPhysExtnTable. The Table is indexed by ifIndex." INDEX { ifIndex } ::= { msanAdslAtucPhysExtnTable 1 } MsanAdslAtucPhysExtnEntry ::= SEQUENCE { msanAdslAtucPhysExtnOpState INTEGER, msanAdslAtucPhysExtnActualStd INTEGER, msanAdslAtucPhysExtnBertError Integer32, msanAdslAtucPhysExtnTxAtmCellCounter Counter32, msanAdslAtucPhysExtnRxAtmCellCounter Integer32, msanAdslAtucPhysExtnStartProgress Integer32, msanAdslAtucPhysExtnIdleBertError Integer32, msanAdslAtucPhysExtnIdleBertCells Integer32, msanAdslAtucPhysExtnBertSync INTEGER, msanAdslAtucPhysExtnParametricTestResult INTEGER, msanAdslAtucPhysExtnSeltInfoValid INTEGER, msanAdslAtucPhysExtnSeltLoopLen Integer32, msanAdslAtucPhysExtnSeltLoopEnd INTEGER, msanAdslAtucPhysExtnSeltLoopGauge INTEGER, msanAdslAtucPhysExtnSeltUpShannonCap Gauge32, msanAdslAtucPhysExtnSeltDownShannonCap Gauge32, msanAdslAtucPhysExtnSeltInbandNoise OCTET STRING, msanAdslAtucPhysExtnSeltTerminationResp OCTET STRING, msanAdslAtucPhysExtnSeltUpMgnAtRate OCTET STRING, msanAdslAtucPhysExtnSeltDownMgnAtRate OCTET STRING, msanAdslAtucPhysExtnDataBoostStatus INTEGER, msanAdslAtucPhysExtnTestArray OCTET STRING, msanAdslAtucPhysExtnChanPerfCD Integer32, msanAdslAtucPhysExtnChanPerfBE Integer32, msanAdslAtucPhysExtnDeltHLINSCus Integer32, msanAdslAtucPhysExtnDeltHLINpsus OCTET STRING, msanAdslAtucPhysExtnDeltHLOGMTus Integer32, msanAdslAtucPhysExtnDeltHLOGpsus OCTET STRING, msanAdslAtucPhysExtnDeltQLNMTus Integer32, msanAdslAtucPhysExtnDeltQLNpsus OCTET STRING, msanAdslAtucPhysExtnDeltLastTxState INTEGER, msanAdslAtucPhysExtnPMState INTEGER, msanAdslAtucPhysExtnChanPerfCU Integer32, msanAdslAtucPhysExtnExtendedPsdStatus TruthValue, msanAdslAtucPhysExtnChipVersion Integer32, msanAdslAtucPhysExtnPilotTone Integer32, msanAdslAtucMSGds Gauge32, msanAdslAtucPhysExtnPsdMaskMode INTEGER, msanAdslAtucPhysExtnDeltSNRMTus Integer32, msanAdslAtucPhysExtnDeltCurrStatus INTEGER, msanAdslAtucSATN Integer32, msanAdslAtucPhysExtnSystemVendorId OCTET STRING, msanAdslAtucPhysExtnSelfTestResult Gauge32, msanAdslAtucPhysExtnG9941VendorId OCTET STRING, msanAdslAtucPhysExtnTsspsUs OCTET STRING, msanAdslAtucPhysExtnActPsdUs Integer32, msanAdslAtucPhysExtnGainspsUs OCTET STRING, msanAdslAtucPhysExtnStartBin Integer32, msanAdslAtucPhysExtnStartupErrorCode INTEGER, msanAdslAtucPhysExtnBitSwapCount Unsigned32, msanAdslAtucPhysExtnModPhase INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.1 msanAdslAtucPhysExtnOpState OBJECT-TYPE SYNTAX INTEGER { idle(0), data(1), handshake(16), training(24), llTest(128), dlTest(131), txTest(132), framerSync(26), fastRetrainInProg(27), bootupLoad(8), atmLpTest(133), discovery(46), deltTraining(139), delt(140) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the operational state of the ATU. Values include idle, handshake, training, etc." ::= { msanAdslAtucPhysExtnEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.2 msanAdslAtucPhysExtnActualStd OBJECT-TYPE SYNTAX INTEGER { t1413(0), gLite(1), gDmt(2), alctl14(3), multimode(4), adi(5), alctl(6), t1413auto(9), adslPlus(48), gspanPlus(64), adsl2(26), adsl2Plus(27), readsl2(28), adsl2Auto(29), adsl2PlusAuto(30), gspanPlusPlus(80) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides actual ATU-C configuration based on outcome of negotiation with ATU-R. In this case, the parameter provides actual standard used for the connection." ::= { msanAdslAtucPhysExtnEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.3 msanAdslAtucPhysExtnBertError OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the No. of bit errors detected during BERT." ::= { msanAdslAtucPhysExtnEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.4 msanAdslAtucPhysExtnTxAtmCellCounter OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object Provides transmit ATM cell counter." ::= { msanAdslAtucPhysExtnEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.5 msanAdslAtucPhysExtnRxAtmCellCounter OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object Provides receive ATM cell counter." ::= { msanAdslAtucPhysExtnEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.6 msanAdslAtucPhysExtnStartProgress OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides current detailed start up information to be used for debugging." ::= { msanAdslAtucPhysExtnEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.7 msanAdslAtucPhysExtnIdleBertError OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of bit errors." ::= { msanAdslAtucPhysExtnEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.8 msanAdslAtucPhysExtnIdleBertCells OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of idle cells." ::= { msanAdslAtucPhysExtnEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.9 msanAdslAtucPhysExtnBertSync OBJECT-TYPE SYNTAX INTEGER { bertOutOfSync(0), bertInSync(128) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates if the Signal is in Sync or not." ::= { msanAdslAtucPhysExtnEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.10 msanAdslAtucPhysExtnParametricTestResult OBJECT-TYPE SYNTAX INTEGER { ok(0), fail(1), dspIfFail(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the Result of the Parametric Test conducted on the Xcvr." ::= { msanAdslAtucPhysExtnEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.11 msanAdslAtucPhysExtnSeltInfoValid OBJECT-TYPE SYNTAX INTEGER { true(1), notConnected(32768), lostConnection(33024), noResponseSeltEngine(33280) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the information validity for the SELT operation conducted on the Xcvr." ::= { msanAdslAtucPhysExtnEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.12 msanAdslAtucPhysExtnSeltLoopLen OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the LOOP Length in Feet once when the SELT information is valid on the Xcvr." ::= { msanAdslAtucPhysExtnEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.13 msanAdslAtucPhysExtnSeltLoopEnd OBJECT-TYPE SYNTAX INTEGER { open(0), short(1), unknown(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the loop is short or open once when the SELT information is valid on the Xcvr." ::= { msanAdslAtucPhysExtnEntry 13 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.14 msanAdslAtucPhysExtnSeltLoopGauge OBJECT-TYPE SYNTAX INTEGER { greater26awg(-1), equal26awg(0), equal24awg(1), less26awg(2), unknownAwg(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the LOOP wire_gauge information once when the SELT information is valid on the Xcvr." ::= { msanAdslAtucPhysExtnEntry 14 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.15 msanAdslAtucPhysExtnSeltUpShannonCap OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the LOOP Upstream Shannon Capacity (in bps) once when the SELT information is valid on the Xcvr." ::= { msanAdslAtucPhysExtnEntry 15 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.16 msanAdslAtucPhysExtnSeltDownShannonCap OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the LOOP Downstream Shannon Capacity (in bps) once when the SELT information is valid on the Xcvr." ::= { msanAdslAtucPhysExtnEntry 16 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.17 msanAdslAtucPhysExtnSeltInbandNoise OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..2048)) MAX-ACCESS read-only STATUS current DESCRIPTION "512 values that indicate inband noise length in dBM/Hz, covering both bands from 0 to 1.1 MHz." ::= { msanAdslAtucPhysExtnEntry 17 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.18 msanAdslAtucPhysExtnSeltTerminationResp OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..720)) MAX-ACCESS read-only STATUS current DESCRIPTION "180 discrete values that indicate termination response magnitude from 0 to 18Kft." ::= { msanAdslAtucPhysExtnEntry 18 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.19 msanAdslAtucPhysExtnSeltUpMgnAtRate OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..1200)) MAX-ACCESS read-only STATUS current DESCRIPTION "300 values that indicate SNR margin in dB/10 at a particular rate are provided, at 100K increments, up to 15 Mbps." ::= { msanAdslAtucPhysExtnEntry 19 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.20 msanAdslAtucPhysExtnSeltDownMgnAtRate OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..1200)) MAX-ACCESS read-only STATUS current DESCRIPTION "300 values that indicate SNR margin in dB/10 at a particular rate are provided, at 100K increments, up to 15 Mbps." ::= { msanAdslAtucPhysExtnEntry 20 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.21 msanAdslAtucPhysExtnDataBoostStatus OBJECT-TYPE SYNTAX INTEGER { enabled(32768), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether DataBoost is utilized for the connection." ::= { msanAdslAtucPhysExtnEntry 21 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.22 msanAdslAtucPhysExtnTestArray OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..1024)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the Parametric Test Array. Every Four octets refer to one element in this array of octets." ::= { msanAdslAtucPhysExtnEntry 22 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.23 msanAdslAtucPhysExtnChanPerfCD OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The near-end delineated total cell count performance parameter is a count of the total number of cells passed through the cell delineation and HEC function process operating on the ATM Data Path while in the SYNC state. (Not available for ADSL)." ::= { msanAdslAtucPhysExtnEntry 23 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.24 msanAdslAtucPhysExtnChanPerfBE OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The near-end idle bit error count performance parameter is a count of the number of bit errors in the idle cell payload received in the ATM Data Path at the near-end. (Not available for ADSL)." ::= { msanAdslAtucPhysExtnEntry 24 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.25 msanAdslAtucPhysExtnDeltHLINSCus OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "DELT-related parameter that provides the scale factor to be applied to the upstream Hlin(f) values.(Not available for ADSL and ADSL2plus)." ::= { msanAdslAtucPhysExtnEntry 25 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.26 msanAdslAtucPhysExtnDeltHLINpsus OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "DELT-related parameter that provides an array of complex upstream Hlin(f) values in linear scale. (Not available for ADSL and ADSL2plus). Every two octets refer to one element in this array of octets." ::= { msanAdslAtucPhysExtnEntry 26 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.27 msanAdslAtucPhysExtnDeltHLOGMTus OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "DELT-related parameter that provides the number of symbols used to measure the upstream Hlog(f).(Not available for ADSL and ADSL2plus)." ::= { msanAdslAtucPhysExtnEntry 27 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.28 msanAdslAtucPhysExtnDeltHLOGpsus OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "DELT-related parameter that provides an array of real upstream Hlog(f) values in dB. (Not available for ADSL and ADSL2plus). Every two octets refer to one element in this array of octets." ::= { msanAdslAtucPhysExtnEntry 28 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.29 msanAdslAtucPhysExtnDeltQLNMTus OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "DELT-related parameter that provides the number of symbols used to measure the upstream QLN(f) values. (Not available for ADSL and ADSL2plus)." ::= { msanAdslAtucPhysExtnEntry 29 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.30 msanAdslAtucPhysExtnDeltQLNpsus OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "DELT-related parameter that provides an array of real upstream QLN(f) values in dB. (Not available for ADSL and ADSL2plus). Every two octets refer to one element in this array of octets." ::= { msanAdslAtucPhysExtnEntry 30 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.31 msanAdslAtucPhysExtnDeltLastTxState OBJECT-TYPE SYNTAX INTEGER { dmtatucg9941(0), dmtatucquiet1(1), dmtatuccomb1(2), dmtatucquiet2(3), dmtatuccomb2(4), dmtatucicomb1(5), dmtatuclineprob(6), dmtatucquiet3(7), dmtatuccomb3(8), dmtatucicomb2(9), dmtatucmsgfmt(10), dmtatucmsgpcb(11), dmtatucquiet4(12), dmtatucreverb1(13), dmtatuctref1(14), dmtatucreverb2(15), dmtatucect(16), dmtatucreverb3(17), dmtatuctref2(18), dmtatucreverb4(19), dmtatucsegue1(20), dmtatucmsg1(21), dmtatucreverb5(22), dmtatucsegue2(23), dmtatucmedley(24), dmtatucexchmarker(25), dmtatucmsg2(26), dmtatucreverb6(27), dmtatucsegue3(28), dmtatucparams(29), dmtatucreverb7(30), dmtatucsegue4(31), dmtatucshowtime(32) } MAX-ACCESS read-only STATUS current DESCRIPTION "DELT-related parameter that provides last successful transmitted initialization state by the ATU-C. (Not available for ADSL and ADSL2plus)." ::= { msanAdslAtucPhysExtnEntry 31 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.32 msanAdslAtucPhysExtnPMState OBJECT-TYPE SYNTAX INTEGER { l0(0), l2(2), l3(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Line Power Management State. (Not available for ADSL)." ::= { msanAdslAtucPhysExtnEntry 32 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.33 msanAdslAtucPhysExtnChanPerfCU OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The near-end user total cell count performance parameter is a count of the total number of cells in the ATM Data Path delivered at the V-C (for ATU-C) or T-R (for ATU-R) interface. (Not available for ADSL)." ::= { msanAdslAtucPhysExtnEntry 33 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.34 msanAdslAtucPhysExtnExtendedPsdStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Conexant parameter that indicates whether an extended upstream PSD is used - for G.Span Plus mode of operation only. Only supported for G.Span Plus, therefore this parameter is not valid for ADSL2/ADSL2plus modes of operation." ::= { msanAdslAtucPhysExtnEntry 34 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.35 msanAdslAtucPhysExtnChipVersion OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Conexant parameter that indicates the DSP version number." ::= { msanAdslAtucPhysExtnEntry 35 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.36 msanAdslAtucPhysExtnPilotTone OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Conexant parameter that indicates the Pilot Tone Index." ::= { msanAdslAtucPhysExtnEntry 36 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.37 msanAdslAtucMSGds OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the Overhead Channel. This feature is not supported by DSLPHY as yet." ::= { msanAdslAtucPhysExtnEntry 37 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.38 msanAdslAtucPhysExtnPsdMaskMode OBJECT-TYPE SYNTAX INTEGER { coMsk2(0), flatMsk(3), cabMsk2(4), coMsk2Rfi(32768), flatMskRfi(32771), cabMsk2Rfi(32772), coMsk2Rfi0(49152), adsl2NonovlpM1(275), adsl2NonovlpM2(291), adsl2NonovlpFlat(259) } MAX-ACCESS read-only STATUS current DESCRIPTION "Conexant parameter that indicates the actual Psd Mask currently being used." ::= { msanAdslAtucPhysExtnEntry 38 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.39 msanAdslAtucPhysExtnDeltSNRMTus OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "DELT-related parameter that provides the number of symbols used to measure the upstream SNR(f) values. (Not available for ADSL and ADSL2plus)" ::= { msanAdslAtucPhysExtnEntry 39 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.40 msanAdslAtucPhysExtnDeltCurrStatus OBJECT-TYPE SYNTAX INTEGER { success(255), failedInsufficientCapacity(17), failedCrcError(34), failedTimeOut(68), failedUnexpectedContent(136), failedUnknown(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "This Conexant parameter indicates the current status of Atuc Line in DELT mode." ::= { msanAdslAtucPhysExtnEntry 40 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.41 msanAdslAtucSATN OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "DELT-related parameter that provides the upstream signal attenuation (length = 4 bytes). (Not available for ADSL and ADSL2plus). For further details, Refer to Section 7.5.1.9 Revised Recommendation G.997.1." ::= { msanAdslAtucPhysExtnEntry 41 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.42 msanAdslAtucPhysExtnSystemVendorId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..9)) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the Vendor ID as inserted by the ATU-C in the Overhead Messages(ADSL2). Typically identifies the ATU-C system integrator which usually refers to the vendor of the smallest field-replaceable unit. ATU-C System Vendor ID may not be the same as ATU-C Vendor ID. It is not available for ADSL. This is string of 8 octets containing 2 octet country code , 4 octet vendor id and 2 octet vendor revision number." ::= { msanAdslAtucPhysExtnEntry 42 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.43 msanAdslAtucPhysExtnSelfTestResult OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Defines the ATU-C selftest result. The most significant octet is: 00 hex if the self-test passed or 01 hex if the self-test failed. Interpretation of the other octets is vendor discretionary and can be interpreted in combination with G.994.1 and system Vendor IDs. For further details, refer to Section 7.4.9 Revised Recommendation G.997.1." ::= { msanAdslAtucPhysExtnEntry 43 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.44 msanAdslAtucPhysExtnG9941VendorId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..9)) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the Vendor ID as inserted by the ATU-C in the G.994.1 CL message. Typically identifies the vendor of the ATU-C G.994.1 functionality. This is string of 8 octets containing 2 octet country code , 4 octet vendor id and 2 octet vendor revision number. For further details, refer to Section 7.4.1 Revised Recommendation G.997.1." ::= { msanAdslAtucPhysExtnEntry 44 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.45 msanAdslAtucPhysExtnTsspsUs OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter provides the Upstream Transmit Spectrum Shaping parameter expressed as the set of break points exchanged during G994.1. Each breakpoint consists in a subcarrier index and the associated shaping parameter. Value of this parameter is in range 0 - 127, in multiples of -0.5 dB. 127 is a special value indicating the subcarrier is not transmitted. It is available only for ADSL2/ADSL2plus.For further details, Refer to Section 7.5.1.21.5 Revised Recommendation G.997.1." ::= { msanAdslAtucPhysExtnEntry 45 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.46 msanAdslAtucPhysExtnActPsdUs OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter defines the average upstream transmit power spectrum density over the used subcarriers delivered by the ATU-C at the U-C reference point, at the instant of measurement. It's value ranges from -90 to 0, in 0.1 dB/Hz steps. It is available only for ADSL2/ADSL2plus. For further details, Refer to Section 7.5.1.14 Revised Recommendation G.997.1." ::= { msanAdslAtucPhysExtnEntry 46 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.47 msanAdslAtucPhysExtnGainspsUs OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter defines the upstream gains allocation table per subcarrier. It is an array of integer values in the 0 to 4093 range for subcarriers 0 to NSCus-1. The gain value is represented as a multiple of 1/512 on linear scale. It is supported for ADSL2/ADSl2plus only." ::= { msanAdslAtucPhysExtnEntry 47 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.48 msanAdslAtucPhysExtnStartBin OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This Gspan++ parameter indicates the start bin of the bit loading up array." ::= { msanAdslAtucPhysExtnEntry 48 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.49 msanAdslAtucPhysExtnStartupErrorCode OBJECT-TYPE SYNTAX INTEGER { startupErrorCodeOk(0), startupErrorCodeMaxnomPsdDs(1), startupErrorCodeMaxnomPsdUs(65536), startupErrorCodePsdMaskDs(2), startupErrorCodePsdMaskUs(131072), startupErrorCodeMaxnomAtpDs(4), startupErrorCodeMaxnomAtpUs(262144) } MAX-ACCESS read-only STATUS current DESCRIPTION "Conexant parameter which indicates the startup error code." ::= { msanAdslAtucPhysExtnEntry 49 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.50 msanAdslAtucPhysExtnBitSwapCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This Conexant parameter indicates the bit swap count. It can read only in data mode" ::= { msanAdslAtucPhysExtnEntry 50 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.2.1.51 msanAdslAtucPhysExtnModPhase OBJECT-TYPE SYNTAX INTEGER { flatRateCheck(0), snrMeasure(1), modRateCheck(2), modShowtime(3), flatShowtime(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Conexant parameter to monitor the status of MoD" ::= { msanAdslAtucPhysExtnEntry 51 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3 msanAdslLineExtnTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanAdslLineExtnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes common attributes describing both ends of the line. It is required for all ADSL physical interfaces. This Table is an extension to adslLineTable defined in rfc-2662." ::= { msanAdsl 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3.1 msanAdslLineExtnEntry OBJECT-TYPE SYNTAX MsanAdslLineExtnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the msanAdslLineExtnTable. The Table is indexed by ifIndex." INDEX { ifIndex } ::= { msanAdslLineExtnTable 1 } MsanAdslLineExtnEntry ::= SEQUENCE { msanAdslLineExtnAction INTEGER, msanAdslLineExtnUtopiaL2RxAddr INTEGER, msanAdslLineExtnUtopiaL2TxAddr INTEGER, msanAdslLineExtnTransAtucCap BITS, msanAdslLineExtnTransAtucActual BITS, msanAdslLineExtnClockType INTEGER, msanAdslLineExtnLineDmtTrellis INTEGER, msanAdslLineExtnTransAturCap BITS, msanAdslLineExtnPMConfPMSF INTEGER, msanAdslLineExtnDeltConfLDSF INTEGER, msanAdslLineExtnTransAtucConfig BITS, msanAdslLineExtnAtucCurrOutputPwr Integer32, msanAdslLineExtnAtucBinSNRMargin OCTET STRING, msanAdslLineExtnUtopiaL2RxAddrSecond INTEGER, msanAdslLineExtnUtopiaL2TxAddrSecond INTEGER, msanAdslLineExtnDsBinSnrUpdate INTEGER, msanAdslLineExtnServiceType INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3.1.1 msanAdslLineExtnAction OBJECT-TYPE SYNTAX INTEGER { startup(0), spectrumReverb(5), analogLb(6), digitalLb(7), atmLp(10), spectrumMedley(26), spectrumPilot(27), spectrumCMtpr(30), spectrumRMtpr(32), hybridLossTest(8193), rcvLinearityTest(8194), rcvFilterTest(8195), rcvPowerPerBinTest(8196), idleNoisePerBinTest(8198), totalIdleNoiseTest(8197), selt(4134), shutdown(101), wakeup(102), abortReq(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "this object indicates parameter that allows actions on a per line basis. These actions include abort, startup, and tests." ::= { msanAdslLineExtnEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3.1.2 msanAdslLineExtnUtopiaL2RxAddr OBJECT-TYPE SYNTAX INTEGER (0..254) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates UTOPIA Level 2 Rx address for a line." ::= { msanAdslLineExtnEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3.1.3 msanAdslLineExtnUtopiaL2TxAddr OBJECT-TYPE SYNTAX INTEGER (0..254) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates UTOPIA Level 2 Tx address for a line." ::= { msanAdslLineExtnEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3.1.4 msanAdslLineExtnTransAtucCap OBJECT-TYPE SYNTAX BITS { ansit1413(0), etsi(1), q9921PotsNonOverlapped(2), q9921PotsOverlapped(3), q9921IsdnNonOverlapped(4), q9921isdnOverlapped(5), q9921tcmIsdnNonOverlapped(6), q9921tcmIsdnOverlapped(7), q9922potsNonOverlapeed(8), q9922potsOverlapped(9), q9922tcmIsdnNonOverlapped(10), q9922tcmIsdnOverlapped(11), q9921tcmIsdnSymmetric(12), adslPlusPotsNonOverlapped(13), q9921GspanPlusPotsNonOverlapped(31), q9921GspanPlusPotsOverlapped(30), vdslNonOverlapped(25), vdslOverlapped(24), q9923Adsl2PotsOverlapped(29), q9923Adsl2PotsNonOverlapped(28), q9925Adsl2PlusPotsOverlapped(27), q9925Adsl2PlusPotsNonOverlapped(26), q9923Readsl2PotsOverlapped(22), q9923Readsl2PotsNonOverlapped(23), adslPlusPotsOverlapped(18), q9921GspanPlusPlusPotsNonOverlapped(20), q9921GspanPlusPlusPotsOverlapped(21), q9923IsdnNonOverlapped(34), q9923IsdnOverlapped(35), q9925IsdnNonOverlapped(42), q9925IsdnOverlapped(43), q9923AnnexMPotsExtUsNonOverlapped(56), q9923AnnexMPotsExtUsOverlapped(57), q9925AnnexMPotsExtUsNonOverlapped(60), q9925AnnexMPotsExtUsOverlapped(61) } MAX-ACCESS read-only STATUS current DESCRIPTION "The transmission modes that the ATU-C is capable of supporting. The modes available are limited by the design of the equipment. REFERENCE Section 7.3.2 ITU G.997.1." ::= { msanAdslLineExtnEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3.1.5 msanAdslLineExtnTransAtucActual OBJECT-TYPE SYNTAX BITS { ansit1413(0), etsi(1), q9921PotsNonOverlapped(2), q9921PotsOverlapped(3), q9921IsdnNonOverlapped(4), q9921isdnOverlapped(5), q9921tcmIsdnNonOverlapped(6), q9921tcmIsdnOverlapped(7), q9922potsNonOverlapeed(8), q9922potsOverlapped(9), q9922tcmIsdnNonOverlapped(10), q9922tcmIsdnOverlapped(11), q9921tcmIsdnSymmetric(12), adslPlusPotsNonOverlapped(13), q9921GspanPlusPotsNonOverlapped(31), q9921GspanPlusPotsOverlapped(30), vdslNonOverlapped(25), vdslOverlapped(24), q9923Adsl2PotsOverlapped(29), q9923Adsl2PotsNonOverlapped(28), q9925Adsl2PlusPotsOverlapped(27), q9925Adsl2PlusPotsNonOverlapped(26), q9923Readsl2PotsOverlapped(22), q9923Readsl2PotsNonOverlapped(23), adslPlusPotsOverlapped(18), q9921GspanPlusPlusPotsNonOverlapped(20), q9921GspanPlusPlusPotsOverlapped(21), q9923IsdnNonOverlapped(34), q9923IsdnOverlapped(35), q9925IsdnNonOverlapped(42), q9925IsdnOverlapped(43), q9923AnnexMPotsExtUsNonOverlapped(56), q9923AnnexMPotsExtUsOverlapped(57), q9925AnnexMPotsExtUsNonOverlapped(60), q9925AnnexMPotsExtUsOverlapped(61) } MAX-ACCESS read-only STATUS current DESCRIPTION "The transmission mode of the ATU-C. This object returns if there is no mode currently known. The initialization with the ATU-R will determine the mode used. REFERENCE Section 7.3.2 ITU G.997.1." ::= { msanAdslLineExtnEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3.1.6 msanAdslLineExtnClockType OBJECT-TYPE SYNTAX INTEGER { oscillator(0), crystal(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates parameter to set use of either crystal or oscillator." ::= { msanAdslLineExtnEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3.1.7 msanAdslLineExtnLineDmtTrellis OBJECT-TYPE SYNTAX INTEGER { trellisOn(1), trellisOff(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Parameter that indicates whether trellis coding has been enabled or disabled. Trellis coding should always be enabled for its clear performance advantage." ::= { msanAdslLineExtnEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3.1.8 msanAdslLineExtnTransAturCap OBJECT-TYPE SYNTAX BITS { ansit1413(0), etsi(1), q9921PotsNonOverlapped(2), q9921PotsOverlapped(3), q9921IsdnNonOverlapped(4), q9921isdnOverlapped(5), q9921tcmIsdnNonOverlapped(6), q9921tcmIsdnOverlapped(7), q9922potsNonOverlapeed(8), q9922potsOverlapped(9), q9922tcmIsdnNonOverlapped(10), q9922tcmIsdnOverlapped(11), q9921tcmIsdnSymmetric(12), adslPlusPotsNonOverlapped(13), q9921GspanPlusPotsNonOverlapped(31), q9921GspanPlusPotsOverlapped(30), vdslNonOverlapped(25), vdslOverlapped(24), q9923Adsl2PotsOverlapped(29), q9923Adsl2PotsNonOverlapped(28), q9925Adsl2PlusPotsOverlapped(27), q9925Adsl2PlusPotsNonOverlapped(26), q9923Readsl2PotsOverlapped(22), q9923Readsl2PotsNonOverlapped(23), adslPlusPotsOverlapped(18), q9921GspanPlusPlusPotsNonOverlapped(20), q9921GspanPlusPlusPotsOverlapped(21), q9923IsdnNonOverlapped(34), q9923IsdnOverlapped(35), q9925IsdnNonOverlapped(42), q9925IsdnOverlapped(43), q9923AnnexMPotsExtUsNonOverlapped(56), q9923AnnexMPotsExtUsOverlapped(57), q9925AnnexMPotsExtUsNonOverlapped(60), q9925AnnexMPotsExtUsOverlapped(61) } MAX-ACCESS read-only STATUS current DESCRIPTION "The transmission modes that the ATU-R is capable of supporting. The modes available are limited by the design of the equipment." ::= { msanAdslLineExtnEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3.1.9 msanAdslLineExtnPMConfPMSF OBJECT-TYPE SYNTAX INTEGER { l3ToL0StateForce(0), l0ToL2StateForce(2), l3StateForce(3), l2ToL0StateForce(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "PM-related parameter used by the ATU-C to force a change in the line state.(Not available for ADSL/ADSL2Plus)." ::= { msanAdslLineExtnEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3.1.10 msanAdslLineExtnDeltConfLDSF OBJECT-TYPE SYNTAX INTEGER { inhibit(0), force(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "DELT-related parameter used by the ATU-C to force the line into loop diagnostics mode.(Not available for ADSL and ADSL2plus)." ::= { msanAdslLineExtnEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3.1.11 msanAdslLineExtnTransAtucConfig OBJECT-TYPE SYNTAX BITS { ansit1413(0), etsi(1), q9921PotsNonOverlapped(2), q9921PotsOverlapped(3), q9921IsdnNonOverlapped(4), q9921isdnOverlapped(5), q9921tcmIsdnNonOverlapped(6), q9921tcmIsdnOverlapped(7), q9922potsNonOverlapeed(8), q9922potsOverlapped(9), q9922tcmIsdnNonOverlapped(10), q9922tcmIsdnOverlapped(11), q9921tcmIsdnSymmetric(12), adslPlusPotsNonOverlapped(13), q9921GspanPlusPotsNonOverlapped(31), q9921GspanPlusPotsOverlapped(30), q9923Adsl2PotsOverlapped(29), q9923Adsl2PotsNonOverlapped(28), q9925Adsl2PlusPotsOverlapped(27), q9925Adsl2PlusPotsNonOverlapped(26), q9923Readsl2PotsOverlapped(22), q9923Readsl2PotsNonOverlapped(23), adslPlusPotsOverlapped(18), q9921GspanPlusPlusPotsNonOverlapped(20), q9921GspanPlusPlusPotsOverlapped(21), q9923IsdnNonOverlapped(34), q9923IsdnOverlapped(35), q9925IsdnNonOverlapped(42), q9925IsdnOverlapped(43), q9923AnnexMPotsExtUsNonOverlapped(56), q9923AnnexMPotsExtUsOverlapped(57), q9925AnnexMPotsExtUsNonOverlapped(60), q9925AnnexMPotsExtUsOverlapped(61) } MAX-ACCESS read-write STATUS current DESCRIPTION "The transmission modes that the ATU-C is capable of supporting. The modes available are limited by the design of the equipment. REFERENCE Section 7.3.2 ITU G.997.1." ::= { msanAdslLineExtnEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3.1.12 msanAdslLineExtnAtucCurrOutputPwr OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter indicates the measure of total output power transmitted by this ATU. The value of this parameter is dynamic and will also show the change in Tx power due to Power Management. For example, the value will decrease in L2 low power mode. This value can be negative" ::= { msanAdslLineExtnEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3.1.13 msanAdslLineExtnAtucBinSNRMargin OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "This Conexant parameter is an array of upstream SNR Margin values in dB. Each array entry represents the SNR Margin value for particular sub carrier." ::= { msanAdslLineExtnEntry 13 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3.1.14 msanAdslLineExtnUtopiaL2RxAddrSecond OBJECT-TYPE SYNTAX INTEGER (0..254) MAX-ACCESS read-only STATUS current DESCRIPTION "Conexant parameter to set UTOPIA Level 2 Rx address for the secondary bearer channel in case of Dual Latency." ::= { msanAdslLineExtnEntry 14 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3.1.15 msanAdslLineExtnUtopiaL2TxAddrSecond OBJECT-TYPE SYNTAX INTEGER (0..254) MAX-ACCESS read-only STATUS current DESCRIPTION "Conexant parameter to set UTOPIA Level 2 Tx address for the secondary bearer channel in case of Dual Latency." ::= { msanAdslLineExtnEntry 15 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3.1.16 msanAdslLineExtnDsBinSnrUpdate OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Conexant parameter to enable or disable collection of downstream SNR bin status" ::= { msanAdslLineExtnEntry 16 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.3.1.17 msanAdslLineExtnServiceType OBJECT-TYPE SYNTAX INTEGER { multimode(1), reserved(2), t1413(3), gDmt(4), adsl2plus(6), adsl2(7), adsl2plusAutoAnnexM(8), adsl2AutoAnnexM(9), reAdsl2(10) } MAX-ACCESS read-only STATUS current DESCRIPTION "The service type configured in ADSL configuration profile which applies for this line. Supported values: 1: multimode 2: reserved 3: T1_413 4: G.DMT 6: ADSL2+ 7: ADSL2 8: ADSL2+ AUTO[+Annex M] 9: ADSL2 AUTO[+Annex M] 10: READSL2" ::= { msanAdslLineExtnEntry 17 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4 msanAdslAturPhysExtnTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanAdslAturPhysExtnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is an extention to adslAtucPhysTable defined in rfc-2662. This table provides one row for each ATUR. Each row contains the Physical Layer Parameters table for that ATUR." ::= { msanAdsl 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1 msanAdslAturPhysExtnEntry OBJECT-TYPE SYNTAX MsanAdslAturPhysExtnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the msanAdslAturPhysExtnTable. The Table is indexed by ifIndex." INDEX { ifIndex } ::= { msanAdslAturPhysExtnTable 1 } MsanAdslAturPhysExtnEntry ::= SEQUENCE { msanAdslAturPhysExtnConfig OCTET STRING, msanAdslAturPhysExtnChanPerfCD Integer32, msanAdslAturPhysExtnChanPerfCU Integer32, msanAdslAturPhysExtnChanPerfBE Integer32, msanAdslAturPhysExtnDeltHLINSCds Integer32, msanAdslAturPhysExtnDeltHLINpsds OCTET STRING, msanAdslAturPhysExtnDeltHLOGMTds Integer32, msanAdslAturPhysExtnDeltHLOGpsus OCTET STRING, msanAdslAturPhysExtnDeltQLNMTds Integer32, msanAdslAturPhysExtnDeltQLNpsds OCTET STRING, msanAdslAturPhysExtnDeltLastTxState INTEGER, msanAdslAturMSGus Gauge32, msanAdslAturDeltSNRMTds Gauge32, msanAdslAturSATN Integer32, msanAdslAturPhysExtnSystemVendorId OCTET STRING, msanAdslAturPhysExtnGainspsDs OCTET STRING, msanAdslAturPhysExtnSelfTestResult Gauge32, msanAdslAturPhysExtnG9941VendorId OCTET STRING, msanAdslAturPhysExtnTsspsDs OCTET STRING, msanAdslAturPhysExtnActPsdDs Integer32, msanAdslAturPhysExtnBitSwapCount Unsigned32, msanAdslAturPhysExtnPsdMaskMode INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.1 msanAdslAturPhysExtnConfig OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..30)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the upstream and downstream ATU-R configuration data, as defined in T1.413 i2, Sections 6.4, 6.6, 7.4, 7.6 and Table 27." ::= { msanAdslAturPhysExtnEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.2 msanAdslAturPhysExtnChanPerfCD OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end delineated total cell count performance parameter is a count of the total number of cells passed through the cell delineation and HEC function process operating on the ATM Data Path while in the SYNC state.(Not available for ADSL)." ::= { msanAdslAturPhysExtnEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.3 msanAdslAturPhysExtnChanPerfCU OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end user total cell count performance parameter is a count of the total number of cells in the ATM Data Path delivered at the V-C (for ATU-C) or T-R (for ATUR) interface. (Not available for ADSL)." ::= { msanAdslAturPhysExtnEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.4 msanAdslAturPhysExtnChanPerfBE OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end idle bit error count performance parameter is a count of the number of bit errors in the idle cell payload received in the ATM Data Path at the far-end. (Not available for ADSL)." ::= { msanAdslAturPhysExtnEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.5 msanAdslAturPhysExtnDeltHLINSCds OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "DELT-related parameter that provides the scale factor to be applied to the downstream Hlin(f) values.(Not available for ADSL and ADSL2plus)." ::= { msanAdslAturPhysExtnEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.6 msanAdslAturPhysExtnDeltHLINpsds OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..2048)) MAX-ACCESS read-only STATUS current DESCRIPTION "DELT-related parameter that provides an array of complex downstream Hlin(f) values in linear scale. (Not available for ADSL and ADSL2plus). Every two octets refer to one element in this array of octets." ::= { msanAdslAturPhysExtnEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.7 msanAdslAturPhysExtnDeltHLOGMTds OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "DELT-related parameter that provides the number of symbols used to measure the downstream Hlog(f). (Not available for ADSL and ADSL2plus)." ::= { msanAdslAturPhysExtnEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.8 msanAdslAturPhysExtnDeltHLOGpsus OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..1024)) MAX-ACCESS read-only STATUS current DESCRIPTION "DELT-related parameter that provides an array of real downstream Hlog(f) values in dB. (Not available for ADSL and ADSL2plus)." ::= { msanAdslAturPhysExtnEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.9 msanAdslAturPhysExtnDeltQLNMTds OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "DELT-related parameter that provides the number of symbols used to measure the downstream QLN(f) values. (Not available for ADSL and ADSL2plus)." ::= { msanAdslAturPhysExtnEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.10 msanAdslAturPhysExtnDeltQLNpsds OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "DELT-related parameter that provides an array of real downstream QLN(f) values in dB. (Not available for ADSL and ADSL2plus). Every two octets refer to one element in this array of octets." ::= { msanAdslAturPhysExtnEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.11 msanAdslAturPhysExtnDeltLastTxState OBJECT-TYPE SYNTAX INTEGER { dmtaturg9941(0), dmtaturquiet1(1), dmtaturcomb1(2), dmtaturquiet2(3), dmtaturcomb2(4), dmtaturicomb1(5), dmtaturlineprob(6), dmtaturquiet3(7), dmtaturcomb3(8), dmtaturicomb2(9), dmtaturmsgfmt(10), dmtaturmsgpcb(11), dmtaturreverb1(12), dmtaturquiet4(13), dmtaturreverb2(14), dmtaturquiet5(15), dmtaturreverb3(16), dmtaturect(17), dmtaturreverb4(18), dmtatursegue1(19), dmtaturreverb5(20), dmtatursegue2(21), dmtaturmsg1(22), dmtaturmedley(23), dmtaturexchmarker(24), dmtaturmsg2(25), dmtaturreverb6(26), dmtatursegue3(27), dmtaturparams(28), dmtaturreverb7(29), dmtatursegue4(30), dmtaturshowtime(31) } MAX-ACCESS read-only STATUS current DESCRIPTION "DELT-related parameter that provides last successful transmitted initialization state by the ATU-R. (Not available for ADSL and ADSL2plus)." ::= { msanAdslAturPhysExtnEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.12 msanAdslAturMSGus OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the Overhead Channel. This feature is not supported by DSLPHY as yet." ::= { msanAdslAturPhysExtnEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.13 msanAdslAturDeltSNRMTds OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "DELT-related parameter that provides the number of symbols used to measure the downstream SNR(f) values. (Not available for ADSL and ADSL2plus)" ::= { msanAdslAturPhysExtnEntry 13 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.14 msanAdslAturSATN OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "DELT-related parameter that provides the downtream signal attenuation (length = 4 bytes). (Not available for ADSL and ADSL2plus). For further details, Refer to Section 7.5.1.9 Revised Recommendation G.997.1." ::= { msanAdslAturPhysExtnEntry 14 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.15 msanAdslAturPhysExtnSystemVendorId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..9)) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the Vendor ID as inserted by the ATU-R in the Embedded Operations Channel(ADSL). Typically identiies the ATU-R system integrator which usually refers to the vendor of the smallest field-replaceable unit. ATU-R System Vendor ID may not be the same as ATU-R G.994.1 Vendor ID. For ADSL2, provides the Vendor ID as inserted by the ATU-R in the Overhead Messages. It is not available for ADSL. This is string of 8 octets containing 2 octet country code , 4 octet vendor id and 2 octet vendor revision number." ::= { msanAdslAturPhysExtnEntry 15 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.16 msanAdslAturPhysExtnGainspsDs OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..1024)) MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter defines the downstream gains allocation table per bin. For further details, Refer to Section 7.5.1.21.3 Revised Recommendation G.997.1. It is supported for ADSL2/ADSl2plus only." ::= { msanAdslAturPhysExtnEntry 16 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.17 msanAdslAturPhysExtnSelfTestResult OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Defines the ATU-R selftest result. The most significant octet is: 00 hex if the self-test passed or 01 hex if the self-test failed. Interpretation of the other octets is vendor discretionary and can be interpreted in combination with G.994.1 and system Vendor IDs. For further details, refer to Section 7.4.10 Revised Recommendation G.997.1." ::= { msanAdslAturPhysExtnEntry 17 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.18 msanAdslAturPhysExtnG9941VendorId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..9)) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the Vendor ID as inserted by the ATU-R in the G.994.1 CLR message.The G.994.1 Vendor ID typically identifies the vendor of the ATU-R G.994.1 functionality. This is string of 8 octets containing 2 octet country code , 4 octet vendor id and 2 octet vendor revision number. For further details, refer to Section 7.4.2 Revised Recommendation G.997.1." ::= { msanAdslAturPhysExtnEntry 18 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.19 msanAdslAturPhysExtnTsspsDs OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter provides the Downstream Transmit Spectrum Shaping parameter expressed as the set of break points exchanged during G994.1. Value of this parameter is in range 0 - 127, in multiples of -0.5 dB. 127 is a special value indicating the subcarrier is not transmitted. It is available only for ADSL2/ADSL2plus. For further details, Refer to Section 7.5.1.21.5 Revised Recommendation G.997.1" ::= { msanAdslAturPhysExtnEntry 19 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.20 msanAdslAturPhysExtnActPsdDs OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter defines the average downstream transmit power spectrum density over the used subcarriers delivered by the ATU-C at the U-C reference point, at the instant of measurement. It's value ranges from -90 to 0, in 0.1 dB/Hz steps. It is available only for ADSL2/ADSL2plus.For further details, Refer to Section 7.5.1.14 Revised Recommendation G.997.1." ::= { msanAdslAturPhysExtnEntry 20 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.21 msanAdslAturPhysExtnBitSwapCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This Conexant parameter indicates the bit swap count. It can read only in data mode" ::= { msanAdslAturPhysExtnEntry 21 } -- 1.3.6.1.4.1.1332.1.1.5.3.36.4.1.22 msanAdslAturPhysExtnPsdMaskMode OBJECT-TYPE SYNTAX INTEGER { coMsk2(0), flatMsk(3), cabMsk2(4), coMsk2Rfi(32768), flatMskRfi(32771), cabMsk2Rfi(32772), coMsk2Rfi0(49152), adsl2NonovlpM1(275), adsl2NonovlpM2(291), adsl2NonovlpFlat(259) } MAX-ACCESS read-only STATUS current DESCRIPTION "This conexant parameter that indicates the actual PSD Mask currently being used by ATU-R" ::= { msanAdslAturPhysExtnEntry 22 } -- 1.3.6.1.4.1.1332.1.1.5.3.37 msanEaps OBJECT IDENTIFIER ::= { msanAdditionalConf 37 } -- 1.3.6.1.4.1.1332.1.1.5.3.37.1 msanEapsGlobal OBJECT IDENTIFIER ::= { msanEaps 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.37.1.1 msanEapsAdminState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Global EAPS administrative state." DEFVAL { disable } ::= { msanEapsGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.37.2 msanEapsDomainTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanEapsDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "EAPS domain configuration." ::= { msanEaps 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.37.2.1 msanEapsDomainEntry OBJECT-TYPE SYNTAX MsanEapsDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanEapsDomainName } ::= { msanEapsDomainTable 1 } MsanEapsDomainEntry ::= SEQUENCE { msanEapsDomainName OCTET STRING, msanEapsDomainDeviceRole INTEGER, msanEapsDomainHelloTime INTEGER, msanEapsDomainFailTimeout INTEGER, msanEapsDomainAdminState INTEGER, msanEapsDomainPrimaryIfIndex Integer32, msanEapsDomainSecondaryIfIndex Integer32, msanEapsDomainCntrlVlanId Integer32, msanEapsDomainRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.37.2.1.2 msanEapsDomainName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..12)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description of the EAPS domain. Each msanEapsDomainName value in this table must be unique." ::= { msanEapsDomainEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.37.2.1.3 msanEapsDomainDeviceRole OBJECT-TYPE SYNTAX INTEGER { master(1), transit(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Role of the node in the EAPS domain (Master or Transit)" DEFVAL { transit } ::= { msanEapsDomainEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.37.2.1.4 msanEapsDomainHelloTime OBJECT-TYPE SYNTAX INTEGER (1..15) MAX-ACCESS read-write STATUS current DESCRIPTION "EAPS domain hello frame send interval. This value must be lower than msanEapsDomainFailTimeout" DEFVAL { 1 } ::= { msanEapsDomainEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.37.2.1.5 msanEapsDomainFailTimeout OBJECT-TYPE SYNTAX INTEGER (2..300) MAX-ACCESS read-write STATUS current DESCRIPTION "EAPS fail timeout. This value must be higher than msanEapsDomainHelloTime" DEFVAL { 3 } ::= { msanEapsDomainEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.37.2.1.6 msanEapsDomainAdminState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "EAPS domain administrative state. State can be changed from disable to enable only when all parameters in this table are defined." DEFVAL { disable } ::= { msanEapsDomainEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.37.2.1.7 msanEapsDomainPrimaryIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "EAPS primary interface. The value must be different from msanEapsSecondaryIfIndex. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. ifType of selected interface can be ethernetCsmacd(6) or ieee8023adLag (161). This parameter can be undefined when EAPS domain is created and msanEapsDomainAdminState is disable. " ::= { msanEapsDomainEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.37.2.1.8 msanEapsDomainSecondaryIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "EAPS secondary interface. The value must be different from msanEapsPrimaryIfIndex. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. ifType of selected interface can be ethernetCsmacd(6) or ieee8023adLag (161). This parameter can be undefined when EAPS domain is created and msanEapsDomainAdminState is disable. " ::= { msanEapsDomainEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.37.2.1.9 msanEapsDomainCntrlVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "EAPS control VLAN ID. Selected VLAN ID must exists in dot1qVlanStaticTable. This parameter can be undefined when EAPS domain is created and msanEapsDomainAdminState is disable. " ::= { msanEapsDomainEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.37.2.1.10 msanEapsDomainRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported]. If msanEapsDomainAdminState is disable, created row can be actived by row status object also when next parameters are not defined: - msanEapsDomainPrimaryifIndex - msanEapsDomainSecondaryifIndex - msanEapsDomainCntrlVlanId " ::= { msanEapsDomainEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.37.3 msanEapsDomainProtVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanEapsDomainProtVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of protected VLANs for EAPS domain." ::= { msanEaps 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.37.3.1 msanEapsDomainProtVlanEntry OBJECT-TYPE SYNTAX MsanEapsDomainProtVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanEapsDomainName, dot1qVlanIndex } ::= { msanEapsDomainProtVlanTable 1 } MsanEapsDomainProtVlanEntry ::= SEQUENCE { msanEapsDomainProtVlanRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.37.3.1.1 msanEapsDomainProtVlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanEapsDomainProtVlanEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.38 msanCpe OBJECT IDENTIFIER ::= { msanAdditionalConf 38 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.1 msanCpeGlobal OBJECT IDENTIFIER ::= { msanCpe 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.1.1 msanCpeReset OBJECT-TYPE SYNTAX Unsigned32 UNITS "ifIndex" MAX-ACCESS read-write STATUS current DESCRIPTION "Reset CPE equipment connected to selected interface index (ifIndex)." DEFVAL { 0 } ::= { msanCpeGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.1.2 msanCpeSendConfig OBJECT-TYPE SYNTAX Unsigned32 UNITS "ifIndex" MAX-ACCESS read-write STATUS current DESCRIPTION "Apply configuration to CPE equipment connected to selected interface index (ifIndex)." DEFVAL { 0 } ::= { msanCpeGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.1.3 msanCpeApiMajorVersion OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "CPE API major version information." ::= { msanCpeGlobal 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.1.4 msanCpeApiMinorVersion OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "CPE API minor version information." ::= { msanCpeGlobal 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.2 msanCpeTypeTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanCpeTypeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of possible CPE types." ::= { msanCpe 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.2.1 msanCpeTypeEntry OBJECT-TYPE SYNTAX MsanCpeTypeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanCpeTypeName } ::= { msanCpeTypeTable 1 } MsanCpeTypeEntry ::= SEQUENCE { msanCpeTypeName OCTET STRING, msanCpeTypePortNum Integer32 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.2.1.1 msanCpeTypeName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Usage name of CPE model." ::= { msanCpeTypeEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.2.1.2 msanCpeTypePortNum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Number of CPE user ports." ::= { msanCpeTypeEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.3 msanCpeIntfTypeTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanCpeIntfTypeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Tabel defines which CPE model can be connected to selected interface." ::= { msanCpe 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.3.1 msanCpeIntfTypeEntry OBJECT-TYPE SYNTAX MsanCpeIntfTypeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex, msanCpeTypeName } ::= { msanCpeIntfTypeTable 1 } MsanCpeIntfTypeEntry ::= SEQUENCE { msanCpeIntfTypeRowStatus RowStatus, msanCpeIntfTypeHwVersion OCTET STRING, msanCpeIntfTypeSwVersion OCTET STRING } -- 1.3.6.1.4.1.1332.1.1.5.3.38.3.1.1 msanCpeIntfTypeRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported. " ::= { msanCpeIntfTypeEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.3.1.2 msanCpeIntfTypeHwVersion OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Connected CPE hardware version." ::= { msanCpeIntfTypeEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.3.1.3 msanCpeIntfTypeSwVersion OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Connected CPE software version." ::= { msanCpeIntfTypeEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.4 msanCpeIntfPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanCpeIntfPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of CPE ports parameters" ::= { msanCpe 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.4.1 msanCpeIntfPortEntry OBJECT-TYPE SYNTAX MsanCpeIntfPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex, msanCpeIntfPortId } ::= { msanCpeIntfPortTable 1 } MsanCpeIntfPortEntry ::= SEQUENCE { msanCpeIntfPortId INTEGER, msanCpeIntfPortPowerMode INTEGER, msanCpeIntfPortLinkMode INTEGER, msanCpeIntfPortPvid INTEGER, msanCpeIntfPortCos INTEGER, msanCpeIntfPortOverrideVid INTEGER, msanCpeIntfPortOverrideCos INTEGER, msanCpeIntfPortProtection INTEGER, msanCpeIntfPortStatus INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.38.4.1.1 msanCpeIntfPortId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "CPE port ID (1 .. n)." ::= { msanCpeIntfPortEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.4.1.2 msanCpeIntfPortPowerMode OBJECT-TYPE SYNTAX INTEGER { normal(0), fullPowerDown(1), sleep(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Power mode of the CPE port. When port is in Sleep(2) mode, automatic wake-up is also activated. " DEFVAL { normal } ::= { msanCpeIntfPortEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.4.1.3 msanCpeIntfPortLinkMode OBJECT-TYPE SYNTAX INTEGER { autonegotiation(0), speed100MbpsFD(1), speed100MbpsHD(2), speed10MbpsFD(3), speed10MbpsHD(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Speed and duplex mode of the CPE port." DEFVAL { autonegotiation } ::= { msanCpeIntfPortEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.4.1.4 msanCpeIntfPortPvid OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Default Vlan ID (pVID) for selected CPE port." DEFVAL { 1 } ::= { msanCpeIntfPortEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.4.1.5 msanCpeIntfPortCos OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Default CoS bit settings for the CPE port." DEFVAL { 0 } ::= { msanCpeIntfPortEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.4.1.6 msanCpeIntfPortOverrideVid OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When enable(1)VLAN ID of received tagged frame on selected CPE port is overwritten with default VLAN ID (msanCpeIntfPortPvid)." DEFVAL { disable } ::= { msanCpeIntfPortEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.4.1.7 msanCpeIntfPortOverrideCos OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When enable(1)CoS value of received tagged frame on selected CPE port is overwritten with default CoS bit settings (msanCpeIntfPortCos)." DEFVAL { disable } ::= { msanCpeIntfPortEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.4.1.8 msanCpeIntfPortProtection OBJECT-TYPE SYNTAX INTEGER { unprotected(0), protected(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanAclProfileStatus = dynamic(2)" DEFVAL { unprotected } ::= { msanCpeIntfPortEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.4.1.9 msanCpeIntfPortStatus OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Profile status. If status is dynamic, profile values can't be edited." ::= { msanCpeIntfPortEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.5 msanCpeTrafficTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanCpeTrafficEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanCpe 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.5.1 msanCpeTrafficEntry OBJECT-TYPE SYNTAX MsanCpeTrafficEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanCpeTrafficId } ::= { msanCpeTrafficTable 1 } MsanCpeTrafficEntry ::= SEQUENCE { msanCpeTrafficId Integer32, msanCpeTrafficName OCTET STRING, msanCpeTrafficSpeed Integer32, msanCpeTrafficFlowCntrlMode INTEGER, msanCpeTrafficRowStatus RowStatus, msanCpeTrafficProtection INTEGER, msanCpeTrafficStatus INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.38.5.1.1 msanCpeTrafficId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Number identifying traffic configuration (1 .. n)." ::= { msanCpeTrafficEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.5.1.2 msanCpeTrafficName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..40)) MAX-ACCESS read-write STATUS current DESCRIPTION "Name identifying traffic configuration. Must be unique value." ::= { msanCpeTrafficEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.5.1.3 msanCpeTrafficSpeed OBJECT-TYPE SYNTAX Integer32 (0..100000) UNITS "kbit/s" MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum bitrate of services using this traffic configuration. Domain value is 0-100000kbit/s, where: - for speeds below 1Mbit/s step is 64kbit/s - for speeds above 1Mbit/s step is 1000kbit/s" ::= { msanCpeTrafficEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.5.1.4 msanCpeTrafficFlowCntrlMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Flow control mode. When enable(1) and speed is to be exceeded, device will send PAUSE flow control packet. If disable(2) packet will be just dropped." DEFVAL { disable } ::= { msanCpeTrafficEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.5.1.5 msanCpeTrafficRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported]. Setting this object to active(1) will activate this entry, if msanCpeTrafficName is defined. Setting this object to destroy(6) will remove this entry. " ::= { msanCpeTrafficEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.5.1.6 msanCpeTrafficProtection OBJECT-TYPE SYNTAX INTEGER { unprotected(0), protected(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanAclProfileStatus = dynamic(2)" DEFVAL { unprotected } ::= { msanCpeTrafficEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.5.1.7 msanCpeTrafficStatus OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Profile status. If status is dynamic, profile values can't be edited." ::= { msanCpeTrafficEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.6 msanCpeServiceTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanCpeServiceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanCpe 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.6.1 msanCpeServiceEntry OBJECT-TYPE SYNTAX MsanCpeServiceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanCpeServiceId } ::= { msanCpeServiceTable 1 } MsanCpeServiceEntry ::= SEQUENCE { msanCpeServiceId Integer32, msanCpeServiceName OCTET STRING, msanCpeServiceCVlanId Integer32, msanCpeServiceCCos Integer32, msanCpeServiceTrafficId Integer32, msanCpeServiceUntaggedPorts OCTET STRING, msanCpeServiceTaggedPorts OCTET STRING, msanCpeServiceCMltcstMode INTEGER, msanCpeServiceRowStatus RowStatus, msanCpeServiceTypeName OCTET STRING, msanCpeServiceProtection INTEGER, msanCpeServiceStatus INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.38.6.1.1 msanCpeServiceId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Number identifying service configuration (0 .. n)." ::= { msanCpeServiceEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.6.1.2 msanCpeServiceName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..40)) MAX-ACCESS read-write STATUS current DESCRIPTION "Name identifying service. Must be unique value." ::= { msanCpeServiceEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.6.1.3 msanCpeServiceCVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Customer VLAN ID, used for all frames belong to this service." DEFVAL { 1 } ::= { msanCpeServiceEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.6.1.4 msanCpeServiceCCos OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "CoS bit settings for all frames belonging to this service." DEFVAL { 0 } ::= { msanCpeServiceEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.6.1.5 msanCpeServiceTrafficId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Reference to parameter msanCpeTrafficId (1 .. n), which identifies traffic configuration . Value 0 is used when traffic configuration is not defined." DEFVAL { 0 } ::= { msanCpeServiceEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.6.1.6 msanCpeServiceUntaggedPorts OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "The set of ports (bitmask) which should transmit egress packets as untagged. When untagged frame is received on this ports set, appropriate default VLAN ID (msanCpeIntfPortPvid) and default CoS bits (msanCpeIntfPortCos) are set." DEFVAL { '0'h } ::= { msanCpeServiceEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.6.1.7 msanCpeServiceTaggedPorts OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "The set of ports (bitmask) where frames can be received only if they have appropriate Customer VLAN ID (msanCpeServiceCVlanId). Otherwise they are dropped. When transmitting frames to this set of ports, VLAN tags are not removed. " DEFVAL { '0'h } ::= { msanCpeServiceEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.6.1.8 msanCpeServiceCMltcstMode OBJECT-TYPE SYNTAX INTEGER { disableIGMPprocessing(0), igmpV2SnoopNormalLeave(1), igmpV2SnoopFastLeave(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Mode of multicast operation for this service." DEFVAL { disableIGMPprocessing } ::= { msanCpeServiceEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.6.1.9 msanCpeServiceRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported]. Setting this object to active(1) will activate this entry, if msanCpeServiceName and msanCpeServiceTrafficId are defined. Setting this object to destroy(6) will remove this entry. " ::= { msanCpeServiceEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.6.1.10 msanCpeServiceTypeName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "Usage name of CPE model. Must be one of predefined msanCpeTypeName values." ::= { msanCpeServiceEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.6.1.11 msanCpeServiceProtection OBJECT-TYPE SYNTAX INTEGER { unprotected(0), protected(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanAclProfileStatus = dynamic(2)" DEFVAL { unprotected } ::= { msanCpeServiceEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.6.1.12 msanCpeServiceStatus OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Profile status. If status is dynamic, profile values can't be edited." ::= { msanCpeServiceEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.7 msanCpeIntfServiceTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanCpeIntfServiceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table links CPE ports on selected interface with appropriate service." ::= { msanCpe 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.38.7.1 msanCpeIntfServiceEntry OBJECT-TYPE SYNTAX MsanCpeIntfServiceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex, msanCpeServiceId } ::= { msanCpeIntfServiceTable 1 } MsanCpeIntfServiceEntry ::= SEQUENCE { msanCpeIntfServiceRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.38.7.1.1 msanCpeIntfServiceRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanCpeIntfServiceEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.39 msanBoard OBJECT IDENTIFIER ::= { msanAdditionalConf 39 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.1 msanBoardGlobal OBJECT IDENTIFIER ::= { msanBoard 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.1.1 msanBoardReset OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Reset board in specified shelf slot ID (>0)." DEFVAL { 0 } ::= { msanBoardGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.2 msanBoardConfTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanBoardConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanBoard 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.2.1 msanBoardConfEntry OBJECT-TYPE SYNTAX MsanBoardConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanBoardConfNr } ::= { msanBoardConfTable 1 } MsanBoardConfEntry ::= SEQUENCE { msanBoardConfNr INTEGER, msanBoardConfParentNr INTEGER, msanBoardConfPosition INTEGER, msanBoardConfType OCTET STRING, msanBoardConfRequiredId OCTET STRING, msanBoardConfActualId OCTET STRING, msanBoardConfSerialNr OCTET STRING, msanBoardConfDescription OCTET STRING, msanBoardConfStatus INTEGER, msanBoardConfRowStatus RowStatus, msanBoardConfSwSteerVersion OCTET STRING, msanBoardConfSwBuildDirectory OCTET STRING, msanBoardConfSwBuildTime OCTET STRING, msanBoardConfSwBranch OCTET STRING, msanBoardConfSwBuildReference OCTET STRING } -- 1.3.6.1.4.1.1332.1.1.5.3.39.2.1.1 msanBoardConfNr OBJECT-TYPE SYNTAX INTEGER (1..1000) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Unique identification of a board." ::= { msanBoardConfEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.2.1.2 msanBoardConfParentNr OBJECT-TYPE SYNTAX INTEGER (1..1000) MAX-ACCESS read-write STATUS current DESCRIPTION "Unique identification of a parent board." ::= { msanBoardConfEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.2.1.3 msanBoardConfPosition OBJECT-TYPE SYNTAX INTEGER (1..1000) MAX-ACCESS read-write STATUS current DESCRIPTION "Position of the board on the parent board. " ::= { msanBoardConfEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.2.1.4 msanBoardConfType OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Type of physical board (e.g. IDC, SGO, SFA, ...). This value is automatically set according to msanBoardConfRequiredId." DEFVAL { "" } ::= { msanBoardConfEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.2.1.5 msanBoardConfRequiredId OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Required identification of a board, which is one of available msanBoardListId values (e.g. UTA6041BA)." ::= { msanBoardConfEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.2.1.6 msanBoardConfActualId OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Actual identification of a board (e.g. UTA6041BA050 - last three numbers define board version)." ::= { msanBoardConfEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.2.1.7 msanBoardConfSerialNr OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Serial number of a board." ::= { msanBoardConfEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.2.1.8 msanBoardConfDescription OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Description of the board." DEFVAL { "" } ::= { msanBoardConfEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.2.1.9 msanBoardConfStatus OBJECT-TYPE SYNTAX INTEGER { boardPresentRunning(1), boardPresentNotAccessible(2), boardNotPresent(3), boardPresentInitProcess(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Physical status of configured board." ::= { msanBoardConfEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.2.1.10 msanBoardConfRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deactivation use notInService(2). For row deletion use destroy(6) (board with management interface can not be deleted). Other values are currently not supported. For row activation next terms must be accomplished: - all requested values (they don't have default definition) must be set - msanBoardConfId is one of available msanBoardListId values " ::= { msanBoardConfEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.2.1.11 msanBoardConfSwSteerVersion OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The unique steer code of installed software. " ::= { msanBoardConfEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.2.1.12 msanBoardConfSwBuildDirectory OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The directory where installed software was build on. " ::= { msanBoardConfEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.2.1.13 msanBoardConfSwBuildTime OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The time when the installed software was built. (DateAndTime textual convention, from SNMPv2-TC) " ::= { msanBoardConfEntry 13 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.2.1.14 msanBoardConfSwBranch OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The repository branch where the installed software was built from." ::= { msanBoardConfEntry 14 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.2.1.15 msanBoardConfSwBuildReference OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The repository reference number of the installed software build branch. " ::= { msanBoardConfEntry 15 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.3 msanBoardListTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanBoardListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanBoard 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.3.1 msanBoardListEntry OBJECT-TYPE SYNTAX MsanBoardListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanBoardListId } ::= { msanBoardListTable 1 } MsanBoardListEntry ::= SEQUENCE { msanBoardListId OCTET STRING, msanBoardListType OCTET STRING } -- 1.3.6.1.4.1.1332.1.1.5.3.39.3.1.1 msanBoardListId OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Identification of supported board (e.g. UTA6041BA)." ::= { msanBoardListEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.39.3.1.2 msanBoardListType OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Type of physical board (e.g. IDC, SGO, SFA, ...)." ::= { msanBoardListEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.40 msanFtpServer OBJECT IDENTIFIER ::= { msanAdditionalConf 40 } -- 1.3.6.1.4.1.1332.1.1.5.3.40.1 msanFtpServerGlobal OBJECT IDENTIFIER ::= { msanFtpServer 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.40.1.1 msanFtpServerAdminState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "FTP server administrative state." DEFVAL { disable } ::= { msanFtpServerGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.41 msanAppRateLimit OBJECT IDENTIFIER ::= { msanAdditionalConf 41 } -- 1.3.6.1.4.1.1332.1.1.5.3.41.1 msanAppRateLimitGlobal OBJECT IDENTIFIER ::= { msanAppRateLimit 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.41.2 msanAppRateLimitTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanAppRateLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanAppRateLimit 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.41.2.1 msanAppRateLimitEntry OBJECT-TYPE SYNTAX MsanAppRateLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanAppRateLimitTable 1 } MsanAppRateLimitEntry ::= SEQUENCE { msanAppRateLimitDhcp Integer32, msanAppRateLimitDhcpState INTEGER, msanAppRateLimitPppoe Integer32, msanAppRateLimitPppoeState INTEGER, msanAppRateLimitIgmp Integer32, msanAppRateLimitIgmpState INTEGER, msanAppRateLimitStp Integer32, msanAppRateLimitStpState INTEGER, msanAppRateLimitMn Integer32, msanAppRateLimitMnState INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.41.2.1.1 msanAppRateLimitDhcp OBJECT-TYPE SYNTAX Integer32 (0..1000) UNITS "pps" MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum number of received DHCP packets in one second (pps) per interface. Value 0 defines there is no limit." ::= { msanAppRateLimitEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.41.2.1.2 msanAppRateLimitDhcpState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administrative state of DHCP traffic rate limiting." DEFVAL { enable } ::= { msanAppRateLimitEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.41.2.1.3 msanAppRateLimitPppoe OBJECT-TYPE SYNTAX Integer32 (0..1000) UNITS "pps" MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum number of received PPPoE packets in one second (pps) per interface. Value 0 defines there is no limit." ::= { msanAppRateLimitEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.41.2.1.4 msanAppRateLimitPppoeState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administrative state of PPPoE traffic rate limiting." ::= { msanAppRateLimitEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.41.2.1.5 msanAppRateLimitIgmp OBJECT-TYPE SYNTAX Integer32 (0..1000) UNITS "pps" MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum number of received DHCP packets in one second (pps) per interface. Value 0 defines there is no limit." ::= { msanAppRateLimitEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.41.2.1.6 msanAppRateLimitIgmpState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administrative state of IGMP traffic rate limiting." ::= { msanAppRateLimitEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.41.2.1.7 msanAppRateLimitStp OBJECT-TYPE SYNTAX Integer32 (0..1000) UNITS "pps" MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum number of received STP packets in one second (pps) per interface. Value 0 defines there is no limit." ::= { msanAppRateLimitEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.41.2.1.8 msanAppRateLimitStpState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administrative state of STP traffic rate limiting." ::= { msanAppRateLimitEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.41.2.1.9 msanAppRateLimitMn OBJECT-TYPE SYNTAX Integer32 (0..1000) UNITS "pps" MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum number of received MN packets (management traffic) in one second (pps) per interface. Value 0 defines there is no limit." ::= { msanAppRateLimitEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.41.2.1.10 msanAppRateLimitMnState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administrative state of MN traffic rate limiting." ::= { msanAppRateLimitEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.50 msanMlinec OBJECT IDENTIFIER ::= { msanAdditionalConf 50 } -- 1.3.6.1.4.1.1332.1.1.5.3.50.1 msanMlinecGlobal OBJECT IDENTIFIER ::= { msanMlinec 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.50.1.1 msanMlinecAdminState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "MLINEC (Multi-Link Network Connectivity) administrative state." ::= { msanMlinecGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.100 msanMulticast OBJECT IDENTIFIER ::= { msanAdditionalConf 100 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.1 msanMulticastGlobal OBJECT IDENTIFIER ::= { msanMulticast 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.2 msanMulticastIntfStaticGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMulticastIntfStaticGroupEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The table attaches static multicast groups to the interfaces." ::= { msanMulticast 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.2.1 msanMulticastIntfStaticGroupEntry OBJECT-TYPE SYNTAX MsanMulticastIntfStaticGroupEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." INDEX { ifIndex, msanMulticastIntfStaticGroupIPAddr } ::= { msanMulticastIntfStaticGroupTable 1 } MsanMulticastIntfStaticGroupEntry ::= SEQUENCE { msanMulticastIntfStaticGroupIPAddr IpAddress, msanMulticastIntfStaticGroupRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.100.2.1.1 msanMulticastIntfStaticGroupIPAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "IP multicast address of valid multicast group." ::= { msanMulticastIntfStaticGroupEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.2.1.2 msanMulticastIntfStaticGroupRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanMulticastIntfStaticGroupEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.3 msanMulticastGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMulticastGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanMulticast 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.3.1 msanMulticastGroupEntry OBJECT-TYPE SYNTAX MsanMulticastGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { dot1qVlanIndex, msanMulticastGroupIpAddr } ::= { msanMulticastGroupTable 1 } MsanMulticastGroupEntry ::= SEQUENCE { msanMulticastGroupIpAddr IpAddress, msanMulticastGroupName OCTET STRING, msanMulticastGroupRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.100.3.1.1 msanMulticastGroupIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "IP multicast address of valid multicast group." ::= { msanMulticastGroupEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.3.1.2 msanMulticastGroupName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Name of multicast group. " ::= { msanMulticastGroupEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.3.1.3 msanMulticastGroupRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported]." ::= { msanMulticastGroupEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.4 msanMulticastAclListTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMulticastAclListEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The table below assigns the symbolic names to the specific multicast ACLs." ::= { msanMulticast 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.4.1 msanMulticastAclListEntry OBJECT-TYPE SYNTAX MsanMulticastAclListEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." INDEX { msanMulticastAclListId } ::= { msanMulticastAclListTable 1 } MsanMulticastAclListEntry ::= SEQUENCE { msanMulticastAclListId INTEGER, msanMulticastAclListName SnmpAdminString, msanMulticastAclListRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.100.4.1.1 msanMulticastAclListId OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Multicast List id. Integer from 0 to 255. " ::= { msanMulticastAclListEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.4.1.2 msanMulticastAclListName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS deprecated DESCRIPTION "ACL list symbolic name. Should be unique." ::= { msanMulticastAclListEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.4.1.3 msanMulticastAclListRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported." ::= { msanMulticastAclListEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.5 msanMulticastAclListGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMulticastAclListGroupEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The table below links the multicast groups to the ACL." ::= { msanMulticast 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.5.1 msanMulticastAclListGroupEntry OBJECT-TYPE SYNTAX MsanMulticastAclListGroupEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." INDEX { msanMulticastAclListId, msanMulticastAclGroupIpAddr } ::= { msanMulticastAclListGroupTable 1 } MsanMulticastAclListGroupEntry ::= SEQUENCE { msanMulticastAclGroupIpAddr IpAddress, msanMulticastAclListGroupRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.100.5.1.1 msanMulticastAclGroupIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "IP multicast address of valid ACL multicast group." ::= { msanMulticastAclListGroupEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.5.1.2 msanMulticastAclListGroupRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanMulticastAclListGroupEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.6 msanMulticastAclIntfListTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMulticastAclIntfListEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The table below assigns the multicast ACL to the interfaces" ::= { msanMulticast 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.6.1 msanMulticastAclIntfListEntry OBJECT-TYPE SYNTAX MsanMulticastAclIntfListEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." INDEX { ifIndex, msanMulticastAclListId } ::= { msanMulticastAclIntfListTable 1 } MsanMulticastAclIntfListEntry ::= SEQUENCE { msanMulticastAclIntfListMode INTEGER, msanMulticastAclIntfListRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.100.6.1.1 msanMulticastAclIntfListMode OBJECT-TYPE SYNTAX INTEGER { accept(1), deny(2) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Defines the mode in which interface for specified ACL list works. " ::= { msanMulticastAclIntfListEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.6.1.2 msanMulticastAclIntfListRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported." ::= { msanMulticastAclIntfListEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.7 msanMulticastAclListVlanGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMulticastAclListVlanGroupEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The table below links the multicast groups to the ACL." ::= { msanMulticast 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.7.1 msanMulticastAclListVlanGroupEntry OBJECT-TYPE SYNTAX MsanMulticastAclListVlanGroupEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." INDEX { msanMulticastAclListId, dot1qVlanIndex, msanMulticastAclListVlanGroupIpAddr } ::= { msanMulticastAclListVlanGroupTable 1 } MsanMulticastAclListVlanGroupEntry ::= SEQUENCE { msanMulticastAclListVlanGroupIpAddr IpAddress, msanMulticastAclListVlanGroupRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.100.7.1.1 msanMulticastAclListVlanGroupIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "IP multicast address of valid ACL multicast group." ::= { msanMulticastAclListVlanGroupEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.7.1.2 msanMulticastAclListVlanGroupRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanMulticastAclListVlanGroupEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.8 msanMulticastIntfVlanStaticGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMulticastIntfVlanStaticGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanMulticast 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.8.1 msanMulticastIntfVlanStaticGroupEntry OBJECT-TYPE SYNTAX MsanMulticastIntfVlanStaticGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex, dot1qVlanIndex, msanMulticastIntfVlanStaticGroupIpAddr } ::= { msanMulticastIntfVlanStaticGroupTable 1 } MsanMulticastIntfVlanStaticGroupEntry ::= SEQUENCE { msanMulticastIntfVlanStaticGroupIpAddr IpAddress, msanMulticastIntfVlanStaticGroupRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.100.8.1.1 msanMulticastIntfVlanStaticGroupIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "IP multicast address of valid multicast group." ::= { msanMulticastIntfVlanStaticGroupEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.8.1.2 msanMulticastIntfVlanStaticGroupRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanMulticastIntfVlanStaticGroupEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.9 msanMulticastAccessListTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMulticastAccessListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table below assigns the symbolic names to the specific multicast ACLs." ::= { msanMulticast 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.9.1 msanMulticastAccessListEntry OBJECT-TYPE SYNTAX MsanMulticastAccessListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanMulticastAccessListName } ::= { msanMulticastAccessListTable 1 } MsanMulticastAccessListEntry ::= SEQUENCE { msanMulticastAccessListName OCTET STRING, msanMulticastAccessListRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.100.9.1.1 msanMulticastAccessListName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "ACL list symbolic name. Should be unique." ::= { msanMulticastAccessListEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.9.1.2 msanMulticastAccessListRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndGo(4). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported." ::= { msanMulticastAccessListEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.10 msanMulticastAccessListGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMulticastAccessListGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table below links the multicast addresses to the ACL list" ::= { msanMulticast 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.10.1 msanMulticastAccessListGroupEntry OBJECT-TYPE SYNTAX MsanMulticastAccessListGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanMulticastAccessListName, dot1qVlanIndex, msanMulticastAccessListGroupIpAddr } ::= { msanMulticastAccessListGroupTable 1 } MsanMulticastAccessListGroupEntry ::= SEQUENCE { msanMulticastAccessListGroupIpAddr IpAddress, msanMulticastAccessListGroupRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.100.10.1.1 msanMulticastAccessListGroupIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "IP multicast address of valid ACL multicast group." ::= { msanMulticastAccessListGroupEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.10.1.2 msanMulticastAccessListGroupRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanMulticastAccessListGroupEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.11 msanMulticastAccessListIntfTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanMulticastAccessListIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table below assigns the multicast ACL list to the interfaces" ::= { msanMulticast 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.11.1 msanMulticastAccessListIntfEntry OBJECT-TYPE SYNTAX MsanMulticastAccessListIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex, msanMulticastAccessListName } ::= { msanMulticastAccessListIntfTable 1 } MsanMulticastAccessListIntfEntry ::= SEQUENCE { msanMulticastAccessListIntfMode INTEGER, msanMulticastAccessListIntfRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.100.11.1.1 msanMulticastAccessListIntfMode OBJECT-TYPE SYNTAX INTEGER { accept(1), deny(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Defines the mode in which interface for specified ACL list works. " ::= { msanMulticastAccessListIntfEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.11.1.2 msanMulticastAccessListIntfRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported." ::= { msanMulticastAccessListIntfEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.12 msanSwitchMFDBTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanSwitchMFDBEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Multicast Forwarding Database table" ::= { msanMulticast 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.12.1 msanSwitchMFDBEntry OBJECT-TYPE SYNTAX MsanSwitchMFDBEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains Forwarding and Filtering information per Component User, Vlan Index, and MAC Address." INDEX { msanSwitchMFDBProtocolType, msanSwitchMFDBVlanId, msanSwitchMFDBMacAddress } ::= { msanSwitchMFDBTable 1 } MsanSwitchMFDBEntry ::= SEQUENCE { msanSwitchMFDBProtocolType INTEGER, msanSwitchMFDBVlanId VlanIndex, msanSwitchMFDBMacAddress MacAddress, msanSwitchMFDBType INTEGER, msanSwitchMFDBDescription DisplayString, msanSwitchMFDBForwardingPortMask PortMask, msanSwitchMFDBFilteringPortMask PortMask } -- 1.3.6.1.4.1.1332.1.1.5.3.100.12.1.1 msanSwitchMFDBProtocolType OBJECT-TYPE SYNTAX INTEGER { static(1), gmrp(2), igmp(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The component that is responsible for this entry in the Multicast Forwarding Database." ::= { msanSwitchMFDBEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.12.1.2 msanSwitchMFDBVlanId OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Vlan Index for which this entry is associated with." ::= { msanSwitchMFDBEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.12.1.3 msanSwitchMFDBMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "A multicast MAC address for which the switch has forwarding and or filtering information." ::= { msanSwitchMFDBEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.12.1.4 msanSwitchMFDBType OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This displays the type of the entry. static(1) - Entries configured by the end user dynamic(2) - Entries added as a result of a learning process or protocol" ::= { msanSwitchMFDBEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.12.1.5 msanSwitchMFDBDescription OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Text description of this multicast table entry." ::= { msanSwitchMFDBEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.12.1.6 msanSwitchMFDBForwardingPortMask OBJECT-TYPE SYNTAX PortMask MAX-ACCESS read-only STATUS current DESCRIPTION "BitMask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table." ::= { msanSwitchMFDBEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.100.12.1.7 msanSwitchMFDBFilteringPortMask OBJECT-TYPE SYNTAX PortMask MAX-ACCESS read-only STATUS current DESCRIPTION "BitMask indicating which ports this entry indicates should be filtered. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table." ::= { msanSwitchMFDBEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.101 msanFiltering OBJECT IDENTIFIER ::= { msanAdditionalConf 101 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.2 msanFilteringGlobal OBJECT IDENTIFIER ::= { msanFiltering 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.3 msanFilteringFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanFilteringFilterEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Defines a list of filters." ::= { msanFiltering 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.3.1 msanFilteringFilterEntry OBJECT-TYPE SYNTAX MsanFilteringFilterEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." INDEX { msanFilteringFilterId } ::= { msanFilteringFilterTable 1 } MsanFilteringFilterEntry ::= SEQUENCE { msanFilteringFilterId Integer32, msanFilteringFilterName OCTET STRING, msanFilteringFilterType INTEGER, msanFilteringFilterRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.101.3.1.1 msanFilteringFilterId OBJECT-TYPE SYNTAX Integer32 (1..64 | 301..500) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Filter identity." ::= { msanFilteringFilterEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.3.1.2 msanFilteringFilterName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Name of filter to be shown." ::= { msanFilteringFilterEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.3.1.3 msanFilteringFilterType OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Type of filter (static or dynamic)." ::= { msanFilteringFilterEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.3.1.4 msanFilteringFilterRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "SNMP row status. Supported values: active(1) - valid entry; createAndGo(4) - used to create a new entry; destroy(6) - removes the entry." DEFVAL { active } ::= { msanFilteringFilterEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.4 msanFilteringAssignFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanFilteringAssignFilterEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This table defines a list of filters assigned to interface." ::= { msanFiltering 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.4.1 msanFilteringAssignFilterEntry OBJECT-TYPE SYNTAX MsanFilteringAssignFilterEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." INDEX { ifIndex, msanFilteringFilterId } ::= { msanFilteringAssignFilterTable 1 } MsanFilteringAssignFilterEntry ::= SEQUENCE { msanFilteringAssignFilterVid Integer32, msanFilteringAssignFilterCos Integer32, msanFilteringAssignFilterDscp Integer32, msanFilteringAssignFilterPrec Integer32, msanFilteringAssignFilterRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.101.4.1.1 msanFilteringAssignFilterVid OBJECT-TYPE SYNTAX Integer32 (0..4094) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "ID of VLAN to be filtered." ::= { msanFilteringAssignFilterEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.4.1.2 msanFilteringAssignFilterCos OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "CoS value to be filtered." ::= { msanFilteringAssignFilterEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.4.1.3 msanFilteringAssignFilterDscp OBJECT-TYPE SYNTAX Integer32 (0..63) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "DSCP field." ::= { msanFilteringAssignFilterEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.4.1.4 msanFilteringAssignFilterPrec OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Precedence in DSCP tag." ::= { msanFilteringAssignFilterEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.4.1.5 msanFilteringAssignFilterRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "SNMP row status. Supported values: active(1) - valid entry; createAndGo(4) - used to create a new entry; destroy(6) - removes the entry." DEFVAL { active } ::= { msanFilteringAssignFilterEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5 msanFilteringRuleTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanFilteringRuleEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This table defines a list of filtering rules associated to filters." ::= { msanFiltering 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1 msanFilteringRuleEntry OBJECT-TYPE SYNTAX MsanFilteringRuleEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." INDEX { msanFilteringRuleId, msanFilteringFilterId } ::= { msanFilteringRuleTable 1 } MsanFilteringRuleEntry ::= SEQUENCE { msanFilteringRuleId Integer32, msanFilteringRuleResponse INTEGER, msanFilteringRuleFromMac MacAddress, msanFilteringRuleFromMacMask MacAddress, msanFilteringRuleFromIp IpAddress, msanFilteringRuleFromMask IpAddress, msanFilteringRuleFromPortLow Unsigned32, msanFilteringRuleFromPortHigh Unsigned32, msanFilteringRuleToMac MacAddress, msanFilteringRuleToMacMask MacAddress, msanFilteringRuleToIp IpAddress, msanFilteringRuleToMask IpAddress, msanFilteringRuleToPortLow Unsigned32, msanFilteringRuleToPortHigh Unsigned32, msanFilteringRuleEtherProto OCTET STRING, msanFilteringRuleIpProto OCTET STRING, msanFilteringRuleIcmType Unsigned32, msanFilteringRulePrec Unsigned32, msanFilteringRuleTos Unsigned32, msanFilteringRuleVid Unsigned32, msanFilteringRuleCos Unsigned32, msanFilteringRuleTag INTEGER, msanFilteringRuleRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.1 msanFilteringRuleId OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Filtering rule identity." ::= { msanFilteringRuleEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.2 msanFilteringRuleResponse OBJECT-TYPE SYNTAX INTEGER { accept(1), deny(2) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Filter response." ::= { msanFilteringRuleEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.3 msanFilteringRuleFromMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Source Ethernet address." ::= { msanFilteringRuleEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.4 msanFilteringRuleFromMacMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Source Ethernet address mask." ::= { msanFilteringRuleEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.5 msanFilteringRuleFromIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Source IP address." ::= { msanFilteringRuleEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.6 msanFilteringRuleFromMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Source IP address mask." ::= { msanFilteringRuleEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.7 msanFilteringRuleFromPortLow OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The lowest number of a source TCP or UDP port." ::= { msanFilteringRuleEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.8 msanFilteringRuleFromPortHigh OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The highest number of a source TCP or UDP port.." ::= { msanFilteringRuleEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.9 msanFilteringRuleToMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Destination Ethernet address." ::= { msanFilteringRuleEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.10 msanFilteringRuleToMacMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Destination Ethernet address mask." ::= { msanFilteringRuleEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.11 msanFilteringRuleToIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Destination IP address." ::= { msanFilteringRuleEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.12 msanFilteringRuleToMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Destination IP address mask." ::= { msanFilteringRuleEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.13 msanFilteringRuleToPortLow OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The lowest number of a destination TCP or UDP port." ::= { msanFilteringRuleEntry 13 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.14 msanFilteringRuleToPortHigh OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The highest number of a destination TCP or UDP port." ::= { msanFilteringRuleEntry 14 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.15 msanFilteringRuleEtherProto OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Ethernet protocol to be filtered." ::= { msanFilteringRuleEntry 15 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.16 msanFilteringRuleIpProto OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS deprecated DESCRIPTION "IP protocol to be filtered." ::= { msanFilteringRuleEntry 16 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.17 msanFilteringRuleIcmType OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "ICMP type. ICMP sends an error message to the transmitter of IP packets and provides information at IP packet processing." ::= { msanFilteringRuleEntry 17 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.18 msanFilteringRulePrec OBJECT-TYPE SYNTAX Unsigned32 (0..7) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Precedence in DSCP tag." ::= { msanFilteringRuleEntry 18 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.19 msanFilteringRuleTos OBJECT-TYPE SYNTAX Unsigned32 (0..15) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "TOS to be filtered." ::= { msanFilteringRuleEntry 19 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.20 msanFilteringRuleVid OBJECT-TYPE SYNTAX Unsigned32 (0..4094) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "ID of VLAN to be filtered." ::= { msanFilteringRuleEntry 20 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.21 msanFilteringRuleCos OBJECT-TYPE SYNTAX Unsigned32 (0..7) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "CoS value to be filtered." ::= { msanFilteringRuleEntry 21 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.22 msanFilteringRuleTag OBJECT-TYPE SYNTAX INTEGER { untagged(1), tagged(2), qinq-tagged(3) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "802.1Q tag." ::= { msanFilteringRuleEntry 22 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.5.1.23 msanFilteringRuleRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "SNMP row status. Supported values: active(1) - valid entry; createAndGo(4) - used to create a new entry; destroy(6) - removes the entry." DEFVAL { active } ::= { msanFilteringRuleEntry 23 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.6 msanFilteringAttachedFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanFilteringAttachedFilterEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This table defines information about filters attached to interface." ::= { msanFiltering 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.6.1 msanFilteringAttachedFilterEntry OBJECT-TYPE SYNTAX MsanFilteringAttachedFilterEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." INDEX { ifIndex, msanFilteringFilterId } ::= { msanFilteringAttachedFilterTable 1 } MsanFilteringAttachedFilterEntry ::= SEQUENCE { msanFilteringAttachedFilterDirect INTEGER, msanFilteringAttachedFilterRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.101.6.1.1 msanFilteringAttachedFilterDirect OBJECT-TYPE SYNTAX INTEGER { in(1), out(2) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Point of attaching a filter." ::= { msanFilteringAttachedFilterEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.101.6.1.2 msanFilteringAttachedFilterRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "SNMP row status. Supported values: active(1) - valid entry; createAndGo(4) - used to create a new entry; destroy(6) - removes the entry." ::= { msanFilteringAttachedFilterEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.102 msanBridge OBJECT IDENTIFIER ::= { msanAdditionalConf 102 } -- 1.3.6.1.4.1.1332.1.1.5.3.102.1 msanBridgeGlobal OBJECT IDENTIFIER ::= { msanBridge 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.102.1.1 msanBridgeMode OBJECT-TYPE SYNTAX INTEGER { bridge(1), ccx(2) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "A bridge operating mode. bridge(1) ccx(2) " ::= { msanBridgeGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.102.1.2 msanBridgeMacTableSize OBJECT-TYPE SYNTAX INTEGER (64..4095) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The maximum MAC table size" ::= { msanBridgeGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.102.1.3 msanBridgeRedAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Enable or disable Random Early Discard functionality." ::= { msanBridgeGlobal 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.102.2 msanBridgeCCXTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanBridgeCCXEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The table contents the information about all CCX pairs." ::= { msanBridge 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.102.2.1 msanBridgeCCXEntry OBJECT-TYPE SYNTAX MsanBridgeCCXEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." INDEX { msanBridgeCCXInterface1, msanBridgeCCXInterface2 } ::= { msanBridgeCCXTable 1 } MsanBridgeCCXEntry ::= SEQUENCE { msanBridgeCCXInterface1 InterfaceIndex, msanBridgeCCXInterface2 InterfaceIndex, msanBridgeCCXRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.102.2.1.1 msanBridgeCCXInterface1 OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The first interface to make cross-connection exchange" ::= { msanBridgeCCXEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.102.2.1.2 msanBridgeCCXInterface2 OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The second interface to make cross-connection exchange" ::= { msanBridgeCCXEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.102.2.1.3 msanBridgeCCXRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanBridgeCCXEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.103 msanIPSG OBJECT IDENTIFIER ::= { msanAdditionalConf 103 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.1 msanIPSGGlobal OBJECT IDENTIFIER ::= { msanIPSG 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.1.1 msanIPSGAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable IPv4 source guard for all interfaces" ::= { msanIPSGGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.1.2 msanIPSGStoreAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable storing of the IP-MAC binds to the interoperation table." ::= { msanIPSGGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.1.3 msanIPSGIpv6AdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable IPv6 source guard for all interfaces" ::= { msanIPSGGlobal 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.1.4 msanIPSGClearDynamicBinds OBJECT-TYPE SYNTAX INTEGER { disable(1), clear-all(2), clear-dhcpv4(3), clear-dhcpv6(4), clear-nd(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear IPSG snooping tables for all ports." ::= { msanIPSGGlobal 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.2 msanIPSGIntfTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanIPSGIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanIPSG 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.2.1 msanIPSGIntfEntry OBJECT-TYPE SYNTAX MsanIPSGIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanIPSGIntfTable 1 } MsanIPSGIntfEntry ::= SEQUENCE { msanIPSGIntfAdminMode INTEGER, msanIPSGIntfBindsLimit Integer32, msanIPSGIntfFilteringMode INTEGER, msanIPSGIntfIpv6AdminMode INTEGER, msanIPSGIntfBindsLimitDhcpv6 Integer32, msanIPSGIntfBindsLimitND Integer32, msanIPSGIntfClearDynamicBinds INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.103.2.1.1 msanIPSGIntfAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable IP Source Guard for the selected interface." DEFVAL { disable } ::= { msanIPSGIntfEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.2.1.2 msanIPSGIntfBindsLimit OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "IPSG binding limit for DHCPv4 snooping table per interface. Value 0 defines there is no limit." DEFVAL { 4 } ::= { msanIPSGIntfEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.2.1.3 msanIPSGIntfFilteringMode OBJECT-TYPE SYNTAX INTEGER { iponly(1), ipmac(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the traffic filtering type. Traffic can be filtered either by IP or by both IP and MAC address." DEFVAL { iponly } ::= { msanIPSGIntfEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.2.1.4 msanIPSGIntfIpv6AdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable IPv6 Source Guard for the selected interface." DEFVAL { disable } ::= { msanIPSGIntfEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.2.1.5 msanIPSGIntfBindsLimitDhcpv6 OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "IPSG binding limit for DHCPv6 (IPv6 DHCP)snooping table per interface. Value 0 defines there is no limit." DEFVAL { 4 } ::= { msanIPSGIntfEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.2.1.6 msanIPSGIntfBindsLimitND OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "IPSG binding limit for ND (IPv6 Neighbor Discovery) snooping table per interface Value 0 defines there is no limit." DEFVAL { 4 } ::= { msanIPSGIntfEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.2.1.7 msanIPSGIntfClearDynamicBinds OBJECT-TYPE SYNTAX INTEGER { disable(1), clear-all(2), clear-dhcpv4(3), clear-dhcpv6(4), clear-nd(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear IPSG snooping tables per interface" ::= { msanIPSGIntfEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.3 msanIPSGBindingsTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanIPSGBindingsEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "DThe table for storing IP source binding" ::= { msanIPSG 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.3.1 msanIPSGBindingsEntry OBJECT-TYPE SYNTAX MsanIPSGBindingsEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." INDEX { ifIndex, msanIPSGBindVlan, msanIPSGBindMac } ::= { msanIPSGBindingsTable 1 } MsanIPSGBindingsEntry ::= SEQUENCE { msanIPSGBindIp IpAddress, msanIPSGBindVlan VlanIndex, msanIPSGBindMac MacAddress, msanIPSGBindLeaseRemainingTime TimeTicks, msanIPSGBindType INTEGER, msanIPSGBindMatchedFrames Counter32, msanIPSGBindRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.103.3.1.1 msanIPSGBindIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Allowed IP address" ::= { msanIPSGBindingsEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.3.1.2 msanIPSGBindVlan OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Allowed VLAN number" ::= { msanIPSGBindingsEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.3.1.3 msanIPSGBindMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Allowed MAC address" ::= { msanIPSGBindingsEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.3.1.4 msanIPSGBindLeaseRemainingTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The period for which the DHCP lease is valid. It is displayed in days, hours, minutes, and seconds. For static IPSG bindings this value is set to 0 (infinitive)." ::= { msanIPSGBindingsEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.3.1.5 msanIPSGBindType OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Type of IPSG binding." ::= { msanIPSGBindingsEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.3.1.6 msanIPSGBindMatchedFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Number of matched frames for selected IPSG binding." ::= { msanIPSGBindingsEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.3.1.7 msanIPSGBindRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported. For row activation next terms must be accomplished: - msanIPSGBindIp must be defined " ::= { msanIPSGBindingsEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.4 msanIPSGIpv4PortStaticBindTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanIPSGIpv4PortStaticBindEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanIPSG 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.4.1 msanIPSGIpv4PortStaticBindEntry OBJECT-TYPE SYNTAX MsanIPSGIpv4PortStaticBindEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex, msanIPSGIpv4PortStaticBindMacAddress, msanIPSGIpv4PortStaticBindVlanId, msanIPSGIpv4PortStaticBindIpAddress } ::= { msanIPSGIpv4PortStaticBindTable 1 } MsanIPSGIpv4PortStaticBindEntry ::= SEQUENCE { msanIPSGIpv4PortStaticBindMacAddress MacAddress, msanIPSGIpv4PortStaticBindVlanId VlanIndex, msanIPSGIpv4PortStaticBindIpAddress InetAddressIPv4, msanIPSGIpv4PortStaticBindMatchedFrames Counter32, msanIPSGIpv4PortStaticBindRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.103.4.1.1 msanIPSGIpv4PortStaticBindMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Allowed MAC address" ::= { msanIPSGIpv4PortStaticBindEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.4.1.2 msanIPSGIpv4PortStaticBindVlanId OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Allowed VLAN number" ::= { msanIPSGIpv4PortStaticBindEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.4.1.3 msanIPSGIpv4PortStaticBindIpAddress OBJECT-TYPE SYNTAX InetAddressIPv4 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Allowed IPv4 address" ::= { msanIPSGIpv4PortStaticBindEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.4.1.4 msanIPSGIpv4PortStaticBindMatchedFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of matched frames for selected IPSG binding." ::= { msanIPSGIpv4PortStaticBindEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.4.1.5 msanIPSGIpv4PortStaticBindRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndGo(4). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported." ::= { msanIPSGIpv4PortStaticBindEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.5 msanIPSGIpv6PortStaticBindTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanIPSGIpv6PortStaticBindEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanIPSG 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.5.1 msanIPSGIpv6PortStaticBindEntry OBJECT-TYPE SYNTAX MsanIPSGIpv6PortStaticBindEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex, msanIPSGIpv6PortStaticBindMacAddress, msanIPSGIpv6PortStaticBindVlanId, msanIPSGIpv6PortStaticBindIpAddress } ::= { msanIPSGIpv6PortStaticBindTable 1 } MsanIPSGIpv6PortStaticBindEntry ::= SEQUENCE { msanIPSGIpv6PortStaticBindMacAddress MacAddress, msanIPSGIpv6PortStaticBindVlanId VlanIndex, msanIPSGIpv6PortStaticBindIpAddress InetAddressIPv6, msanIPSGIpv6PortStaticBindMatchedFrames Counter32, msanIPSGIpv6PortStaticBindRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.103.5.1.1 msanIPSGIpv6PortStaticBindMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Allowed MAC address" ::= { msanIPSGIpv6PortStaticBindEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.5.1.2 msanIPSGIpv6PortStaticBindVlanId OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Allowed VLAN number" ::= { msanIPSGIpv6PortStaticBindEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.5.1.3 msanIPSGIpv6PortStaticBindIpAddress OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Allowed IPv6 address" ::= { msanIPSGIpv6PortStaticBindEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.5.1.4 msanIPSGIpv6PortStaticBindMatchedFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of matched frames for selected IPSG binding." ::= { msanIPSGIpv6PortStaticBindEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.5.1.5 msanIPSGIpv6PortStaticBindRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndGo(4). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported." ::= { msanIPSGIpv6PortStaticBindEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.6 msanIPSGPortBindCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanIPSGPortBindCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "DThe table for storing IP source binding" ::= { msanIPSG 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.6.1 msanIPSGPortBindCurrentEntry OBJECT-TYPE SYNTAX MsanIPSGPortBindCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanIPSGPortBindCurrentId } ::= { msanIPSGPortBindCurrentTable 1 } MsanIPSGPortBindCurrentEntry ::= SEQUENCE { msanIPSGPortBindCurrentId Integer32, msanIPSGPortBindCurrentIfIndex InterfaceIndex, msanIPSGPortBindCurrentMacAddress MacAddress, msanIPSGPortBindCurrentVlanId VlanIndex, msanIPSGPortBindCurrentIpAddressType InetAddressType, msanIPSGPortBindCurrentIpAddress InetAddress, msanIPSGPortBindCurrentLeaseRemainingTime TimeTicks, msanIPSGPortBindCurrentType INTEGER, msanIPSGPortBindCurrentMatchedFrames Counter32 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.6.1.1 msanIPSGPortBindCurrentId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table index." ::= { msanIPSGPortBindCurrentEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.6.1.2 msanIPSGPortBindCurrentIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Port index (ifIndex value)." ::= { msanIPSGPortBindCurrentEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.6.1.3 msanIPSGPortBindCurrentMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Allowed MAC address" ::= { msanIPSGPortBindCurrentEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.6.1.4 msanIPSGPortBindCurrentVlanId OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Allowed VLAN number" ::= { msanIPSGPortBindCurrentEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.6.1.5 msanIPSGPortBindCurrentIpAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the type of ip address: ipv4[1], ipv6[2]." ::= { msanIPSGPortBindCurrentEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.6.1.6 msanIPSGPortBindCurrentIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Allowed IP address" ::= { msanIPSGPortBindCurrentEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.6.1.7 msanIPSGPortBindCurrentLeaseRemainingTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The period for which the DHCP lease is valid. It is displayed in days, hours, minutes, and seconds. For static IPSG bindings this value is set to 0 (infinitive)." ::= { msanIPSGPortBindCurrentEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.6.1.8 msanIPSGPortBindCurrentType OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic-dhcpv4(2), dynamic-dhcpv6(3), dynamic-nd(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of IPSG binding." ::= { msanIPSGPortBindCurrentEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.103.6.1.9 msanIPSGPortBindCurrentMatchedFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of matched frames for selected IPSG binding." ::= { msanIPSGPortBindCurrentEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.105 msanVlan OBJECT IDENTIFIER ::= { msanAdditionalConf 105 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.1 msanVlanGlobal OBJECT IDENTIFIER ::= { msanVlan 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.1.1 msanDVlanTagMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Controls the Double Vlan Tag mode on the system." ::= { msanVlanGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.1.2 msanVlanRemarkAdminState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Global VLAN Remarking administrative state." DEFVAL { disable } ::= { msanVlanGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.1.3 msanInternalVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Internal Vlan ID." ::= { msanVlanGlobal 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.2 msanPortVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanPortVlanEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Vlan config parameters per port." ::= { msanVlan 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.2.1 msanPortVlanEntry OBJECT-TYPE SYNTAX MsanPortVlanEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." INDEX { ifIndex } ::= { msanPortVlanTable 1 } MsanPortVlanEntry ::= SEQUENCE { msanPortVlanMode INTEGER, msanPortVlanStackPriority INTEGER, msanPortVlanStackVlanId Integer32 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.2.1.1 msanPortVlanMode OBJECT-TYPE SYNTAX INTEGER { access(0), trunk(1), dot1qtunnel(2), vlanStacking(3) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Interface vlan mode." ::= { msanPortVlanEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.2.1.2 msanPortVlanStackPriority OBJECT-TYPE SYNTAX INTEGER { mapPriorityFromOuterTag(0), priority1(1), priority2(2), priority3(3), priority4(4), priority5(5), priority6(6), priority7(7) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Priority of inner tag when interface is in vlanStacking mode (msanPortVlanMode=vlanStacking)." ::= { msanPortVlanEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.2.1.3 msanPortVlanStackVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Vlan ID of inner tag when interface is in vlanStacking mode (msanPortVlanMode=vlanStacking). " ::= { msanPortVlanEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.3 msanPortDVlanMapTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanPortDVlanMapEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Ingress mapping of inner VID to outer VID different from default (PVID) mapping. " ::= { msanVlan 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.3.1 msanPortDVlanMapEntry OBJECT-TYPE SYNTAX MsanPortDVlanMapEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Description." INDEX { ifIndex, msanPortDVlanMapInTagVlanId } ::= { msanPortDVlanMapTable 1 } MsanPortDVlanMapEntry ::= SEQUENCE { msanPortDVlanMapInTagVlanId Integer32, msanPortDVlanMapOutTagVlanId Integer32, msanPortDVlanMapRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.105.3.1.1 msanPortDVlanMapInTagVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Inner tag VLAN ID. DVlan functionality is used when interface is in dot1qtunnel mode." ::= { msanPortDVlanMapEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.3.1.2 msanPortDVlanMapOutTagVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS deprecated DESCRIPTION "Outer tag VLAN ID added for inner tag VLAN ID (msanPortDVlanMapInTagVlanId). DVlan functionality is used when interface is in dot1qtunnel mode. Value of -1 indicates that outer tag is not added for selected inner tag VLAN ID." ::= { msanPortDVlanMapEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.3.1.3 msanPortDVlanMapRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported]. Setting this object to active(1) will activate this entry. Setting this object to destroy(6) will remove this entry. " ::= { msanPortDVlanMapEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.4 msanPortVlanRemarkTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanPortVlanRemarkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Vlan remarking table for ingress traffic (per port). Note: All defined Vlan remarking rules for ingress traffic also add , automatically, reverse Vlan remarking rule for egress traffic on same port." ::= { msanVlan 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.4.1 msanPortVlanRemarkEntry OBJECT-TYPE SYNTAX MsanPortVlanRemarkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex, msanPortVlanRemarkSrcVlanId } ::= { msanPortVlanRemarkTable 1 } MsanPortVlanRemarkEntry ::= SEQUENCE { msanPortVlanRemarkSrcVlanId Integer32, msanPortVlanRemarkDstVlanId Integer32, msanPortVlanRemarkRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.105.4.1.1 msanPortVlanRemarkSrcVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Ingress traffic Source VLAN ID which will be changed to Destination VLAN ID (msanPortVlanRemarkDstVlanId) by VLAN remarking rule." ::= { msanPortVlanRemarkEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.4.1.2 msanPortVlanRemarkDstVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Destination VLAN ID to which will be changed Source VLAN ID of ingress traffic (msanPortVlanRemarkSrcVlanId) by VLAN remarking rule." ::= { msanPortVlanRemarkEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.4.1.3 msanPortVlanRemarkRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported. For row activation next terms must be accomplished: - msanPortVlanRemarkDstVlanId must be defined (default value not defined) Note: All defined Vlan remarking rules for ingress traffic also add , automatically, reverse Vlan remarking rule for egress traffic on same port. " ::= { msanPortVlanRemarkEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.5 msanPortDVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanPortDVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanVlan 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.5.1 msanPortDVlanEntry OBJECT-TYPE SYNTAX MsanPortDVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanPortDVlanTable 1 } MsanPortDVlanEntry ::= SEQUENCE { msanPortDVlanTagMode INTEGER, msanPortDVlanStackVlanId Integer32, msanPortDVlanStackPriority INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.105.5.1.1 msanPortDVlanTagMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administrative state of 802.1Q tunneling (DVLAN) mode." DEFVAL { disable } ::= { msanPortDVlanEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.5.1.2 msanPortDVlanStackVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Vlan ID of inner tag when interface is in vlanStacking mode. Interface is in vlanStacking mode when msanPortDVlanTagMode=enable and msanPortDVlanStackVlanId>=0. msanPortDVlanStackVlanId value of -1 indicates that vlanStacking mode is not activated." ::= { msanPortDVlanEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.5.1.3 msanPortDVlanStackPriority OBJECT-TYPE SYNTAX INTEGER { priority0(0), priority1(1), priority2(2), priority3(3), priority4(4), priority5(5), priority6(6), priority7(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "Priority of inner tag when interface is in vlanStacking mode. Interface is in vlanStacking mode when msanPortDVlanTagMode=enable and msanPortDVlanStackVlanId>=0." DEFVAL { priority0 } ::= { msanPortDVlanEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.6 msanPortDVlanConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanPortDVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Ingress mapping of inner VID to outer VID different from default (PVID) mapping. " ::= { msanVlan 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.6.1 msanPortDVlanConfigEntry OBJECT-TYPE SYNTAX MsanPortDVlanConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex, msanDVlanConfigInTagVlanId, msanDVlanConfigInTagPriority } ::= { msanPortDVlanConfigTable 1 } MsanPortDVlanConfigEntry ::= SEQUENCE { msanDVlanConfigInTagVlanId Integer32, msanDVlanConfigInTagPriority INTEGER, msanDVlanConfigOutTagVlanId Integer32, msanDVlanConfigOutTagPriority INTEGER, msanDVlanConfigRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.105.6.1.1 msanDVlanConfigInTagVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Inner tag VLAN ID. DVlan functionality is used when interface is in dot1qtunnel mode." ::= { msanPortDVlanConfigEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.6.1.2 msanDVlanConfigInTagPriority OBJECT-TYPE SYNTAX INTEGER { priority0(0), priority1(1), priority2(2), priority3(3), priority4(4), priority5(5), priority6(6), priority7(7), unspecified(8) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Priority of inner tag. Value unspecified(8) defines that rule line applies to all packets with appropriate msanDVlanConfigInTagVlanId, except if packet match to other more specific rule." ::= { msanPortDVlanConfigEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.6.1.3 msanDVlanConfigOutTagVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Outer tag VLAN ID added for inner tag VLAN ID (msanPortDVlanConfigInTagVlanId). DVlan functionality is used when interface is in dot1qtunnel mode. Value of -1 indicates that outer tag is not added for selected inner tag VLAN ID." ::= { msanPortDVlanConfigEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.6.1.4 msanDVlanConfigOutTagPriority OBJECT-TYPE SYNTAX INTEGER { priority0(0), priority1(1), priority2(2), priority3(3), priority4(4), priority5(5), priority6(6), priority7(7), unspecified(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "Priority of outer tag. Value unspecified(8) defines that msanDVlanMapInTagPriority is copied to outer tag." DEFVAL { priority0 } ::= { msanPortDVlanConfigEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.6.1.5 msanDVlanConfigRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported]. Setting this object to active(1) will activate this entry. Setting this object to destroy(6) will remove this entry. " ::= { msanPortDVlanConfigEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.7 msanPortVlanRemarkAdminTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanPortVlanRemarkAdminEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanVlan 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.105.7.1 msanPortVlanRemarkAdminEntry OBJECT-TYPE SYNTAX MsanPortVlanRemarkAdminEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanPortVlanRemarkAdminTable 1 } MsanPortVlanRemarkAdminEntry ::= SEQUENCE { msanPortVlanRemarkAdminMode INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.105.7.1.1 msanPortVlanRemarkAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administrative mode for VLAN Remarking" ::= { msanPortVlanRemarkAdminEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.106 msanAtm OBJECT IDENTIFIER ::= { msanAdditionalConf 106 } -- 1.3.6.1.4.1.1332.1.1.5.3.106.1 msanAtmGlobal OBJECT IDENTIFIER ::= { msanAtm 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.106.2 msanPortAtmPvcTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanPortAtmPvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanAtm 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.106.2.1 msanPortAtmPvcEntry OBJECT-TYPE SYNTAX MsanPortAtmPvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex, msanPortAtmPvcVpi, msanPortAtmPvcVci } ::= { msanPortAtmPvcTable 1 } MsanPortAtmPvcEntry ::= SEQUENCE { msanPortAtmPvcVpi Integer32, msanPortAtmPvcVci Integer32, msanPortAtmPvcPvid INTEGER, msanPortAtmPvcRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.106.2.1.1 msanPortAtmPvcVpi OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "ATM-PVC(Permanent Virtual Circuits) VPI(Virtual Path Identifier) value." ::= { msanPortAtmPvcEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.106.2.1.2 msanPortAtmPvcVci OBJECT-TYPE SYNTAX Integer32 (32..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "ATM-PVC(Permanent Virtual Circuits) VCI(Virtual Channel Identifier) value." ::= { msanPortAtmPvcEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.106.2.1.3 msanPortAtmPvcPvid OBJECT-TYPE SYNTAX INTEGER (0..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "The PVID, the VLAN ID assigned to untagged frames or Priority-Tagged frames received on this ATM-PVC(Permanent Virtual Circuits). Value 0 defines that PVID is not set." DEFVAL { '0'b } ::= { msanPortAtmPvcEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.106.2.1.4 msanPortAtmPvcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported]. Setting this object to active(1) will activate this entry. Setting this object to destroy(6) will remove this entry." ::= { msanPortAtmPvcEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.107 msanEnergyMeter OBJECT IDENTIFIER ::= { msanAdditionalConf 107 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.1 msanEnergyMeterGlobal OBJECT IDENTIFIER ::= { msanEnergyMeter 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.1.1 msanEnergyMeterIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Energy meter's Ip address." ::= { msanEnergyMeterGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.1.2 msanEnergyMeterTcpPort OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Energy meter's Tcp port." ::= { msanEnergyMeterGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.1.3 msanEnergyMeterAddress OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Energy meter's address." ::= { msanEnergyMeterGlobal 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.1.4 msanEnergyMeterPassword OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Energy meter's password." DEFVAL { 0 } ::= { msanEnergyMeterGlobal 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.1.5 msanEnergyMeterSerialNo OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "Energy meter's serial number." ::= { msanEnergyMeterGlobal 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.1.6 msanEnergyMeterDateTime OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Energy meter's date and time in format: year-month-day, hour:minutes:seconds" ::= { msanEnergyMeterGlobal 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.1.7 msanEnergyMeterCurrTariff OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Energy meter's current active tariff." ::= { msanEnergyMeterGlobal 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.1.8 msanEnergyMeterCurrPower OBJECT-TYPE SYNTAX Unsigned32 UNITS "0.01 kW" MAX-ACCESS read-only STATUS current DESCRIPTION "Energy meter's current measured power." ::= { msanEnergyMeterGlobal 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.1.9 msanEnergyMeterCoreVersion OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Energy meter's current version number." ::= { msanEnergyMeterGlobal 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.1.10 msanEnergyMeterFwType OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Energy meter's current firmware type." ::= { msanEnergyMeterGlobal 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.1.11 msanEnergyMeterFwVersion OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Energy meter's current firmware version." ::= { msanEnergyMeterGlobal 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.1.12 msanEnergyMeterFwCreationDate OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Energy meter's current firmware creation date in format: year-month-day" ::= { msanEnergyMeterGlobal 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.2 msanEnergyMeterEnergyTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanEnergyMeterEnergyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Energy values." ::= { msanEnergyMeter 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.2.1 msanEnergyMeterEnergyEntry OBJECT-TYPE SYNTAX MsanEnergyMeterEnergyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanEnergyMeterTariff, msanEnergyMeterDepth } ::= { msanEnergyMeterEnergyTable 1 } MsanEnergyMeterEnergyEntry ::= SEQUENCE { msanEnergyMeterTariff Unsigned32, msanEnergyMeterDepth Unsigned32, msanEnergyMeterEnergyValue Unsigned32 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.2.1.1 msanEnergyMeterTariff OBJECT-TYPE SYNTAX Unsigned32 (0..7) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is msanEnergyMeterTariff index in msanEnergyMeterEnergyTable Defines tariff. 0 – tariff No1, 1 – tariff No2, …, 7 - tariff No8" ::= { msanEnergyMeterEnergyEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.2.1.2 msanEnergyMeterDepth OBJECT-TYPE SYNTAX Unsigned32 (0..13) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is msanEnergyMeterDepth index in msanEnergyMeterEnergyTable. Defines time span. 0 – current value, 1 – value at the end of previous month, 2 – value at the end of 2. month ago, …, 13 –value at the end of the 13. month ago" ::= { msanEnergyMeterEnergyEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.2.1.3 msanEnergyMeterEnergyValue OBJECT-TYPE SYNTAX Unsigned32 UNITS "0.01 kWh" MAX-ACCESS read-only STATUS current DESCRIPTION "Energy value." ::= { msanEnergyMeterEnergyEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.3 msanEnergyMeterEnergySumTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanEnergyMeterEnergySumEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Energy sum values of all tariffs." ::= { msanEnergyMeter 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.3.1 msanEnergyMeterEnergySumEntry OBJECT-TYPE SYNTAX MsanEnergyMeterEnergySumEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanEnergyMeterDepth } ::= { msanEnergyMeterEnergySumTable 1 } MsanEnergyMeterEnergySumEntry ::= SEQUENCE { msanEnergyMeterEnergySumValue Unsigned32 } -- 1.3.6.1.4.1.1332.1.1.5.3.107.3.1.1 msanEnergyMeterEnergySumValue OBJECT-TYPE SYNTAX Unsigned32 UNITS "0.01 kWh" MAX-ACCESS read-only STATUS current DESCRIPTION "Energy sum value of all tariffs" ::= { msanEnergyMeterEnergySumEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.108 msanArpInspection OBJECT IDENTIFIER ::= { msanAdditionalConf 108 } -- 1.3.6.1.4.1.1332.1.1.5.3.108.1 msanArpInspectionGlobal OBJECT IDENTIFIER ::= { msanArpInspection 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.108.1.1 msanArpInspectionAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable global dynamic arp inspection " ::= { msanArpInspectionGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.108.2 msanArpInspectionPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanArpInspectionPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Arp Inspection." ::= { msanArpInspection 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.108.2.1 msanArpInspectionPortEntry OBJECT-TYPE SYNTAX MsanArpInspectionPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanArpInspectionPortTable 1 } MsanArpInspectionPortEntry ::= SEQUENCE { msanArpInspectionPortAdminMode INTEGER, msanArpInspectionPortStatDroppedFrames INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.108.2.1.1 msanArpInspectionPortAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable dynamic arp inspection for the selected interface." DEFVAL { disable } ::= { msanArpInspectionPortEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.108.2.1.2 msanArpInspectionPortStatDroppedFrames OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of discarded ARP packets on interface." ::= { msanArpInspectionPortEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.108.3 msanArpInspectionVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanArpInspectionVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Arp Inspection." ::= { msanArpInspection 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.108.3.1 msanArpInspectionVlanEntry OBJECT-TYPE SYNTAX MsanArpInspectionVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { dot1qVlanIndex } ::= { msanArpInspectionVlanTable 1 } MsanArpInspectionVlanEntry ::= SEQUENCE { msanArpInspectionVlanAdminMode INTEGER, msanArpInspectionVlanStatDroppedFrames INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.108.3.1.1 msanArpInspectionVlanAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable dynamic arp inspection per vlan." DEFVAL { disable } ::= { msanArpInspectionVlanEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.108.3.1.2 msanArpInspectionVlanStatDroppedFrames OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of discarded ARP packets per vlan." ::= { msanArpInspectionVlanEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.109 msanIsa OBJECT IDENTIFIER ::= { msanAdditionalConf 109 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.1 msanIsaGlobal OBJECT IDENTIFIER ::= { msanIsa 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.1.1 msanIsaTalAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "ISA TAL functionality global admin mode." DEFVAL { disable } ::= { msanIsaGlobal 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.1.2 msanIsaDasServerPort OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "ISA Radius DAS (Dynamic Authorization Server) port number." DEFVAL { 3799 } ::= { msanIsaGlobal 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.1.3 msanIsaDasServerSecret OBJECT-TYPE SYNTAX DisplayString (SIZE (0..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "ISA Radius DAS (Dynamic Authorization Server) shared secret." ::= { msanIsaGlobal 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.1.4 msanIsaRadiusServerRetries OBJECT-TYPE SYNTAX Unsigned32 (1..15) MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum number of retransmissions of a ISA Radius request packet." DEFVAL { 3 } ::= { msanIsaGlobal 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.1.5 msanIsaRadiusServerTimeout OBJECT-TYPE SYNTAX Unsigned32 (1..30) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Time out duration (in seconds) before packets are retransmitted to ISA Radius server" DEFVAL { 3 } ::= { msanIsaGlobal 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.2 msanIsaStatistics OBJECT IDENTIFIER ::= { msanIsa 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.2.1 msanIsaPortStatTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanIsaPortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanIsaStatistics 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1 msanIsaPortStatEntry OBJECT-TYPE SYNTAX MsanIsaPortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanIsaPortStatTable 1 } MsanIsaPortStatEntry ::= SEQUENCE { msanIsaPortStatTalMatchedFrames Counter32, msanIsaPortStatTalDroppedFrames Counter32, msanIsaPortStatAuthenReqSent Counter32, msanIsaPortStatAuthenReqConfirmed Counter32, msanIsaPortStatAuthenReqRejected Counter32, msanIsaPortStatAuthenTimeoutExpired Counter32, msanIsaPortStatAuthorReqSent Counter32, msanIsaPortStatAuthorReqConfirmed Counter32, msanIsaPortStatAuthorReqRejected Counter32, msanIsaPortStatAuthorTimeoutExpired Counter32 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.1 msanIsaPortStatTalMatchedFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of TAL matched frames." ::= { msanIsaPortStatEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.2 msanIsaPortStatTalDroppedFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of TAL dropped frames." ::= { msanIsaPortStatEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.3 msanIsaPortStatAuthenReqSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of sent Authentication requests." ::= { msanIsaPortStatEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.4 msanIsaPortStatAuthenReqConfirmed OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of confirmed Authentication requests." ::= { msanIsaPortStatEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.6 msanIsaPortStatAuthenReqRejected OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of rejected Authentication requests." ::= { msanIsaPortStatEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.7 msanIsaPortStatAuthenTimeoutExpired OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of expired Authentication timeouts." ::= { msanIsaPortStatEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.8 msanIsaPortStatAuthorReqSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of sent Authorization requests." ::= { msanIsaPortStatEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.9 msanIsaPortStatAuthorReqConfirmed OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of confirmed Authorization requests." ::= { msanIsaPortStatEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.10 msanIsaPortStatAuthorReqRejected OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of rejected Authorization requests." ::= { msanIsaPortStatEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.11 msanIsaPortStatAuthorTimeoutExpired OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of expired Authorization timeouts." ::= { msanIsaPortStatEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.2.2 msanIsaStatLoginReq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Cumulative number of Login requests." ::= { msanIsaStatistics 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.2.3 msanIsaStatLoginUnsuccessfulReq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of unsuccessful login requests." ::= { msanIsaStatistics 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.3 msanIsaRadiusServerTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanIsaRadiusServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanIsa 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.3.1 msanIsaRadiusServerEntry OBJECT-TYPE SYNTAX MsanIsaRadiusServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanIsaRadiusServerIpAddress, msanIsaRadiusServerType } ::= { msanIsaRadiusServerTable 1 } MsanIsaRadiusServerEntry ::= SEQUENCE { msanIsaRadiusServerIpAddress IpAddress, msanIsaRadiusServerType INTEGER, msanIsaRadiusServerPort Unsigned32, msanIsaRadiusServerSecret DisplayString, msanIsaRadiusServerPrimaryMode INTEGER, msanIsaRadiusServerRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.109.3.1.1 msanIsaRadiusServerIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "ISA Radius server IP address. " ::= { msanIsaRadiusServerEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.3.1.2 msanIsaRadiusServerType OBJECT-TYPE SYNTAX INTEGER { authentication(1), accounting(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "ISA Radius server type." ::= { msanIsaRadiusServerEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.3.1.3 msanIsaRadiusServerPort OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION " ISA Radius server port number. If msanIsaRadiusServerType = authentication(1) then default port value is 1812. If msanIsaRadiusServerType = accounting(2) then default port value is 1813." ::= { msanIsaRadiusServerEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.3.1.4 msanIsaRadiusServerSecret OBJECT-TYPE SYNTAX DisplayString (SIZE (0..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "ISA Radius server shared secret." DEFVAL { "" } ::= { msanIsaRadiusServerEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.3.1.5 msanIsaRadiusServerPrimaryMode OBJECT-TYPE SYNTAX INTEGER { primary(1), secondary(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "ISA Radius server primary mode. Only one server can be defined as primary(1)." ::= { msanIsaRadiusServerEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.3.1.6 msanIsaRadiusServerRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported. For row activation parameter msanIsaRadiusServerType must be defined." ::= { msanIsaRadiusServerEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.5 msanIsaPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanIsaPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanIsa 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.5.1 msanIsaPortEntry OBJECT-TYPE SYNTAX MsanIsaPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanIsaPortTable 1 } MsanIsaPortEntry ::= SEQUENCE { msanIsaPortTalAdminMode INTEGER, msanIsaPortAuthentication INTEGER, msanIsaPortAuthorization INTEGER, msanIsaPortAccounting INTEGER, msanIsaPortLoginMask BITS, msanIsaPortLoginUserPatternMask OCTET STRING, msanIsaPortTalAutomaticReq INTEGER } -- 1.3.6.1.4.1.1332.1.1.5.3.109.5.1.1 msanIsaPortTalAdminMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "ISA TAL functionality admin mode." DEFVAL { disable } ::= { msanIsaPortEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.5.1.2 msanIsaPortAuthentication OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "ISA Authentication administrative state." DEFVAL { enable } ::= { msanIsaPortEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.5.1.3 msanIsaPortAuthorization OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "ISA Authorization administrative state." DEFVAL { enable } ::= { msanIsaPortEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.5.1.4 msanIsaPortAccounting OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "ISA Accounting administrative state." DEFVAL { disable } ::= { msanIsaPortEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.5.1.5 msanIsaPortLoginMask OBJECT-TYPE SYNTAX BITS { circuitId(0), remoteId(1), vendorId(2), clientId(3), sourceMAC(4), sourceIP(5), userPattern(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "ISA login mask." DEFVAL { { circuitId } } ::= { msanIsaPortEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.5.1.6 msanIsaPortLoginUserPatternMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of input packet that is send to Radius server, if userPattern bit is set in msanIsaPortLoginMask. Empty string indicates that parameter has not been defined." ::= { msanIsaPortEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.5.1.7 msanIsaPortTalAutomaticReq OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "TAL automatic request state." DEFVAL { disable } ::= { msanIsaPortEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.6 msanIsaTalPortMatchTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanIsaTalPortMatchEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanIsa 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.6.1 msanIsaTalPortMatchEntry OBJECT-TYPE SYNTAX MsanIsaTalPortMatchEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { ifIndex } ::= { msanIsaTalPortMatchTable 1 } MsanIsaTalPortMatchEntry ::= SEQUENCE { msanIsaTalPortMatchEthertype Integer32, msanIsaTalPortMatchMacSrcAddr MacAddress, msanIsaTalPortMatchMacSrcMask MacAddress, msanIsaTalPortMatchVlanId Integer32, msanIsaTalPortMatchIpSrcAddr IpAddress, msanIsaTalPortMatchIpSrcMask IpAddress, msanIsaTalPortMatchDhcpType INTEGER, msanIsaTalPortMatchDhcpOpt60VendorId DisplayString, msanIsaTalPortMatchDhcpOpt61ClientId DisplayString, msanIsaTalPortMatchDhcpOpt61ClientIdMacAddr MacAddress, msanIsaTalPortMatchDhcpOpt82RemoteId DisplayString, msanIsaTalPortMatchUserBits OCTET STRING, msanIsaTalPortMatchUserMask OCTET STRING } -- 1.3.6.1.4.1.1332.1.1.5.3.109.6.1.1 msanIsaTalPortMatchEthertype OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified EtherType value. A value of -1 indicates that parameter has not been defined. " DEFVAL { -1 } ::= { msanIsaTalPortMatchEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.6.1.2 msanIsaTalPortMatchMacSrcAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified Source MAC address. Empty string indicates that parameter has not been defined." DEFVAL { ''b } ::= { msanIsaTalPortMatchEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.6.1.3 msanIsaTalPortMatchMacSrcMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanIsaTalPortMatchMacSrcAddr that is compared with input packet. Empty string indicates that parameter has not been defined " DEFVAL { ''b } ::= { msanIsaTalPortMatchEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.6.1.4 msanIsaTalPortMatchVlanId OBJECT-TYPE SYNTAX Integer32 (-1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified VLAN ID value (1-4094). A value of -1 indicates that parameter has not been defined " ::= { msanIsaTalPortMatchEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.6.1.5 msanIsaTalPortMatchIpSrcAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified source IP address. Empty string indicates that parameter has not been defined. " DEFVAL { ''h } ::= { msanIsaTalPortMatchEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.6.1.6 msanIsaTalPortMatchIpSrcMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanIsaTalPortMatchIpSrcAddr that is compared with input packet. Empty string indicates that parameter has not been defined " DEFVAL { ''h } ::= { msanIsaTalPortMatchEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.6.1.7 msanIsaTalPortMatchDhcpType OBJECT-TYPE SYNTAX INTEGER { undefined(0), discover(1), request(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified DHCP type value. " DEFVAL { undefined } ::= { msanIsaTalPortMatchEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.6.1.8 msanIsaTalPortMatchDhcpOpt60VendorId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified DHCP option 60 vendorId value. Empty string indicates that parameter has not been defined." DEFVAL { "" } ::= { msanIsaTalPortMatchEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.6.1.9 msanIsaTalPortMatchDhcpOpt61ClientId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified DHCP option 61 clientId value. Empty string indicates that parameter has not been defined." DEFVAL { "" } ::= { msanIsaTalPortMatchEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.6.1.10 msanIsaTalPortMatchDhcpOpt61ClientIdMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified DHCP option 61 MAC address. Empty string indicates that parameter has not been defined." DEFVAL { ''b } ::= { msanIsaTalPortMatchEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.6.1.11 msanIsaTalPortMatchDhcpOpt82RemoteId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified DHCP option 82 remoteId value. Empty string indicates that parameter has not been defined." DEFVAL { "" } ::= { msanIsaTalPortMatchEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.6.1.12 msanIsaTalPortMatchUserBits OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified user defined bits. Empty string indicates that parameter has not been defined." DEFVAL { ''h } ::= { msanIsaTalPortMatchEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.6.1.13 msanIsaTalPortMatchUserMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanIsaTalPortMatchUserBits that is compared with input packet. Empty string indicates that parameter has not been defined." DEFVAL { ''h } ::= { msanIsaTalPortMatchEntry 13 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.7 msanIsaTalPatternMatchTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanIsaTalPatternMatchEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to store the pattern match name, pattern rules and the corresponding login mask for the pattern match." ::= { msanIsa 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.7.1 msanIsaTalPatternMatchEntry OBJECT-TYPE SYNTAX MsanIsaTalPatternMatchEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table contains the a unique pattern match along with the loginmask to identify the user login packets." INDEX { msanIsaTalPatternMatchName } ::= { msanIsaTalPatternMatchTable 1 } MsanIsaTalPatternMatchEntry ::= SEQUENCE { msanIsaTalPatternMatchName OCTET STRING, msanIsaTalPatternMatchEthertype Integer32, msanIsaTalPatternMatchMacSrcAddr MacAddress, msanIsaTalPatternMatchMacSrcMask MacAddress, msanIsaTalPatternMatchVlanId Integer32, msanIsaTalPatternMatchIpSrcAddr IpAddress, msanIsaTalPatternMatchIpSrcMask IpAddress, msanIsaTalPatternMatchDhcpType INTEGER, msanIsaTalPatternMatchDhcpOpt60VendorId DisplayString, msanIsaTalPatternMatchDhcpOpt61ClientId DisplayString, msanIsaTalPatternMatchDhcpOpt61ClientIdMacAddr MacAddress, msanIsaTalPatternMatchDhcpOpt82RemoteId DisplayString, msanIsaTalPatternMatchUserBits OCTET STRING, msanIsaTalPatternMatchUserMask OCTET STRING, msanIsaTalPatternMatchLoginMask BITS, msanIsaTalPatternMatchRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.109.7.1.1 msanIsaTalPatternMatchName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..64)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Pattern match name." ::= { msanIsaTalPatternMatchEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.7.1.2 msanIsaTalPatternMatchEthertype OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified EtherType value. A value of -1 indicates that parameter has not been defined. " DEFVAL { -1 } ::= { msanIsaTalPatternMatchEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.7.1.3 msanIsaTalPatternMatchMacSrcAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified Source MAC address. Empty string indicates that parameter has not been defined." DEFVAL { ''b } ::= { msanIsaTalPatternMatchEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.7.1.4 msanIsaTalPatternMatchMacSrcMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanIsaTalPatternMatchMacSrcAddr that is compared with input packet. Empty string indicates that parameter has not been defined" DEFVAL { ''b } ::= { msanIsaTalPatternMatchEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.7.1.5 msanIsaTalPatternMatchVlanId OBJECT-TYPE SYNTAX Integer32 (-1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified VLAN ID value (1-4094). A value of -1 indicates that parameter has not been defined" ::= { msanIsaTalPatternMatchEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.7.1.6 msanIsaTalPatternMatchIpSrcAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified source IP address. Empty string indicates that parameter has not been defined. " DEFVAL { ''h } ::= { msanIsaTalPatternMatchEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.7.1.7 msanIsaTalPatternMatchIpSrcMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanIsaTalPatternMatchIpSrcAddr that is compared with input packet. Empty string indicates that parameter has not been defined" DEFVAL { ''h } ::= { msanIsaTalPatternMatchEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.7.1.8 msanIsaTalPatternMatchDhcpType OBJECT-TYPE SYNTAX INTEGER { undefined(0), discover(1), request(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified DHCP type value. " DEFVAL { undefined } ::= { msanIsaTalPatternMatchEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.7.1.9 msanIsaTalPatternMatchDhcpOpt60VendorId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified DHCP option 60 vendorId value. Empty string indicates that parameter has not been defined." DEFVAL { "" } ::= { msanIsaTalPatternMatchEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.7.1.10 msanIsaTalPatternMatchDhcpOpt61ClientId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified DHCP option 61 clientId value. Empty string indicates that parameter has not been defined." DEFVAL { "" } ::= { msanIsaTalPatternMatchEntry 10 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.7.1.11 msanIsaTalPatternMatchDhcpOpt61ClientIdMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified DHCP option 61 MAC address. Empty string indicates that parameter has not been defined." DEFVAL { ''b } ::= { msanIsaTalPatternMatchEntry 11 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.7.1.12 msanIsaTalPatternMatchDhcpOpt82RemoteId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified DHCP option 82 remoteId value. Empty string indicates that parameter has not been defined." DEFVAL { "" } ::= { msanIsaTalPatternMatchEntry 12 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.7.1.13 msanIsaTalPatternMatchUserBits OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "Match incoming packet frame with specified user defined bits. Empty string indicates that parameter has not been defined." DEFVAL { ''h } ::= { msanIsaTalPatternMatchEntry 13 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.7.1.14 msanIsaTalPatternMatchUserMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "This mask value identifies the portion of msanIsaTalPatternMatchUserBits that is compared with input packet. Empty string indicates that parameter has not been defined." DEFVAL { ''h } ::= { msanIsaTalPatternMatchEntry 14 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.7.1.15 msanIsaTalPatternMatchLoginMask OBJECT-TYPE SYNTAX BITS { circuitId(0), remoteId(1), vendorId(2), clientId(3), sourceMAC(4), sourceIP(5), userPattern(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "Login mask for the current pattern match. This is used to generate the UserId." DEFVAL { { circuitId } } ::= { msanIsaTalPatternMatchEntry 15 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.7.1.16 msanIsaTalPatternMatchRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. A new row is created using createAndWait(5) [createAndGo(4) is not supported] The value active(1) activates the entry. Setting this object to destroy6) will remove this entry." ::= { msanIsaTalPatternMatchEntry 16 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.8 msanIsaTalPortPatternMatchTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanIsaTalPortPatternMatchEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A connection between Pattern Matches and device ports. An entry is created in this table whenever a pattern match need to be attached to a downlink port." ::= { msanIsa 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.109.8.1 msanIsaTalPortPatternMatchEntry OBJECT-TYPE SYNTAX MsanIsaTalPortPatternMatchEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table contains the a unique pattern match on a port along with the loginmask to identify the user login packets." INDEX { ifIndex, msanIsaTalPatternMatchName } ::= { msanIsaTalPortPatternMatchTable 1 } MsanIsaTalPortPatternMatchEntry ::= SEQUENCE { msanIsaTalPortPatternMatchRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.109.8.1.1 msanIsaTalPortPatternMatchRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported." ::= { msanIsaTalPortPatternMatchEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.110 msanSync OBJECT IDENTIFIER ::= { msanAdditionalConf 110 } -- 1.3.6.1.4.1.1332.1.1.5.3.110.1 msanSyncGlobal OBJECT IDENTIFIER ::= { msanSync 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.110.2 msanSyncTable OBJECT-TYPE SYNTAX SEQUENCE OF MsanSyncEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { msanSync 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.110.2.1 msanSyncEntry OBJECT-TYPE SYNTAX MsanSyncEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { msanSyncBoardPosition, msanSyncSourcePriority } ::= { msanSyncTable 1 } MsanSyncEntry ::= SEQUENCE { msanSyncBoardPosition INTEGER, msanSyncSourcePriority INTEGER, msanSyncSourceType INTEGER, msanSyncSourceId INTEGER, msanSyncSourceEthPortId InterfaceIndex, msanSyncDestinationType INTEGER, msanSyncDestinationMlvdsId INTEGER, msanSyncSourceSuitability INTEGER, msanSyncSourceActivity INTEGER, msanSyncRowStatus RowStatus } -- 1.3.6.1.4.1.1332.1.1.5.3.110.2.1.1 msanSyncBoardPosition OBJECT-TYPE SYNTAX INTEGER (1..20) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Central ethernet board position." ::= { msanSyncEntry 1 } -- 1.3.6.1.4.1.1332.1.1.5.3.110.2.1.2 msanSyncSourcePriority OBJECT-TYPE SYNTAX INTEGER (1..6) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Synchronization source priority: 1-first priority, 2-second priority....." ::= { msanSyncEntry 2 } -- 1.3.6.1.4.1.1332.1.1.5.3.110.2.1.3 msanSyncSourceType OBJECT-TYPE SYNTAX INTEGER { ext-2mhz(4), ext-10mhz(5), ext-1hz(6), mlvds-bp(8), pps-bp(14), ptp-eth(15), sync-eth(16), free-run(40) } MAX-ACCESS read-write STATUS current DESCRIPTION "Synchronization source type: ext-2mhz(4) - synchronization on extended source 2MHz, ext-10mhz(5) - synchronization on extended source 10MHz, ext-1hz(6) - synchronization on extended source 1Hz, mlvds-bp(8) - synchronization on MLVDS, pps-bp(14) - synchronization on PPS, ptp-eth(15)- synchronization on PtP Ethernet, sync-eth(16) - synchronization on Synchronous Ethernet, free-run(40) - free-run synchronization" ::= { msanSyncEntry 3 } -- 1.3.6.1.4.1.1332.1.1.5.3.110.2.1.4 msanSyncSourceId OBJECT-TYPE SYNTAX INTEGER { input-1(1), input-2(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Synchronization source identity. msanSyncSourceId can be used when msanSyncSourceType has one of values: - ext-2mhz(4), - ext-10mhz(5), - ext-1hz(6), - mlvds-bp(8), - pps-bp(14), - free-run(40) msanSyncSourceId can be set only to input-1(1), when msanSyncSourceType is pps-bp(14) or free-run(40). " ::= { msanSyncEntry 4 } -- 1.3.6.1.4.1.1332.1.1.5.3.110.2.1.5 msanSyncSourceEthPortId OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-write STATUS current DESCRIPTION "Synchronization source ethernet Port Id (value of ifIndex). msanSyncSourceEthPortId can be used, when msanSyncSourceType has ptp-eth(15) or sync-eth(16) value." ::= { msanSyncEntry 5 } -- 1.3.6.1.4.1.1332.1.1.5.3.110.2.1.6 msanSyncDestinationType OBJECT-TYPE SYNTAX INTEGER { local(0), global(10) } MAX-ACCESS read-write STATUS current DESCRIPTION "Synchronization destination type: local(0) - synchronization signal is used only on local board global(0) - synchronization signal is sent to MLVDS bus" ::= { msanSyncEntry 6 } -- 1.3.6.1.4.1.1332.1.1.5.3.110.2.1.7 msanSyncDestinationMlvdsId OBJECT-TYPE SYNTAX INTEGER { mlvds-1(1), mlvds-2(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Destination MLVDS bus Identity. This parameter is used when msanSyncDestinationType has global(1) value." ::= { msanSyncEntry 7 } -- 1.3.6.1.4.1.1332.1.1.5.3.110.2.1.8 msanSyncSourceSuitability OBJECT-TYPE SYNTAX INTEGER { undefined(0), suitable(1), unsuitable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Source Suitability." ::= { msanSyncEntry 8 } -- 1.3.6.1.4.1.1332.1.1.5.3.110.2.1.9 msanSyncSourceActivity OBJECT-TYPE SYNTAX INTEGER { undefined(0), active(1), inactive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Source Activity ." ::= { msanSyncEntry 9 } -- 1.3.6.1.4.1.1332.1.1.5.3.110.2.1.10 msanSyncRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported. For row activation next terms must be defined - msanSyncSourceType - msanSyncSourceMlvdsId or msanSyncSourcePortId - msanSyncDestionationType - msanSyncDestionaMlvdsId if msanSyncDestionType=global(10) " ::= { msanSyncEntry 10 } END -- -- ISKRATEL-MSAN-MIB.mib --