-- ============================================================================ -- Copyright (C) 2014 by HUAWEI TECHNOLOGIES. All rights reserved. -- Description: Huawei TDM Modem management MIB definition. -- Reference: -- Version: V1.02 -- ============================================================================ HUAWEI-TDMCPE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, IpAddress, Gauge32, Unsigned32, Integer32 FROM SNMPv2-SMI DisplayString FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ifIndex FROM RFC1213-MIB huaweiMgmt FROM HUAWEI-MIB; hwTdmMIB MODULE-IDENTITY LAST-UPDATED "201406230900Z" ORGANIZATION "Huawei Technologies Co.,Ltd." CONTACT-INFO "Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China Website: http://www.huawei.com Email: support@huawei.com " DESCRIPTION "Huawei TDM Modem management MIB definition." -- Revision history REVISION "201406230900Z" DESCRIPTION "V1.02, Correct the ORGANIZATION and CONTACT-INFO information." REVISION "201201020900Z" DESCRIPTION "V1.01, Add new nodes, including hwTdmCommonConfiguration,hwTdmAdtranScriptTable, hwTdmAdtranScriptEntry, hwTdmAdtranScript and hwTdmAdtranScriptResult. modify the description of the whole file." REVISION "200506211000Z" DESCRIPTION "V1.00,Finishing TDM management basic MIB definition." ::= { huaweiMgmt 30 } -- -- Groups in hwTdmMIB -- hwTdmMIBObjects OBJECT IDENTIFIER ::= { hwTdmMIB 1 } hwTdmMIBConformance OBJECT IDENTIFIER ::= { hwTdmMIB 2 } -- -- Groups in hwTdmMIBObjects -- hwTdmTftpObjects OBJECT IDENTIFIER ::= { hwTdmMIBObjects 1 } hwTdmModemObjects OBJECT IDENTIFIER ::= { hwTdmMIBObjects 2 } hwTdmPortObjects OBJECT IDENTIFIER ::= { hwTdmMIBObjects 3 } -- hwTdmTraps OBJECT IDENTIFIER ::= { hwTdmMIBObjects 4 } hwTdmCommonConfiguration OBJECT IDENTIFIER ::= { hwTdmMIBObjects 4 } -- -- Groups in hwTdmPortObjects -- hwTdmPortConfObjects OBJECT IDENTIFIER ::= { hwTdmPortObjects 1 } hwTdmPortStatObjects OBJECT IDENTIFIER ::= { hwTdmPortObjects 2 } -- -- Groups in hwTdmMIBConformance -- hwTdmMIBCompliances OBJECT IDENTIFIER ::= { hwTdmMIBConformance 1 } hwTdmMIBGroups OBJECT IDENTIFIER ::= { hwTdmMIBConformance 2 } -- -- ASMi52A Modem TFTP Table -- hwTdmTftpTable OBJECT-TYPE SYNTAX SEQUENCE OF HwTdmTftpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM modem tftp status. This information describe the TFTP server IP address, the file name, the TFTP command and TFTP status.The index of this table is ifIndex." ::= { hwTdmTftpObjects 1 } hwTdmTftpEntry OBJECT-TYPE SYNTAX HwTdmTftpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM modem tftp status. This information describe the TFTP server IP address, the file name, the TFTP command and TFTP status.The index of this entry is ifIndex." INDEX { ifIndex } ::= { hwTdmTftpTable 1 } HwTdmTftpEntry ::= SEQUENCE { hwTdmTftpFileServerIP IpAddress, hwTdmTftpFileName DisplayString, hwTdmTftpFileTransCmd INTEGER, -- hwTdmTftpRetryTimeout -- Unsigned32, -- hwTdmTftpTotalTimeout -- Unsigned32, hwTdmTftpStatus INTEGER } hwTdmTftpFileServerIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This attribute indicates the TFTP server to update the modem software.This must be set before start the software download!" ::= { hwTdmTftpEntry 1 } hwTdmTftpFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..14)) MAX-ACCESS read-write STATUS current DESCRIPTION "This attribute indicates the name of the file to be sent to the modem. This must be set before start the software download!" ::= { hwTdmTftpEntry 2 } hwTdmTftpFileTransCmd OBJECT-TYPE SYNTAX INTEGER { noOp(1), downloadSW(2), uploadConf(3), downloadConf(4), stop(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "The command to be executed on hwTdmTftpFileName at hwTdmTftpFileServerIP. Options: 1. noOp(1) - Indicates that no operation. 2. downloadSW(2) - Indicates that down load softwire. 3. uploadConf(3) - Indicates that upload configuration. 4. downloadConf(4) - Indicates that down load configuration. 5. stop(5) - Indicates that stopping the current operation. " DEFVAL { noOp } ::= { hwTdmTftpEntry 3 } -- hwTdmTftpRetryTimeout OBJECT-TYPE -- SYNTAX Unsigned32 (1..255) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "TFTP retry timeout." -- DEFVAL { 30 } -- ::= { hwTdmTftpEntry 4 } -- hwTdmTftpTotalTimeout OBJECT-TYPE -- SYNTAX Unsigned32 (1..255) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "TFTP total timeout." -- DEFVAL { 240 } -- ::= { hwTdmTftpEntry 5 } hwTdmTftpStatus OBJECT-TYPE SYNTAX INTEGER { noOp(1), connecting(2), transferringData(3), timeOut(4), endedOk(5), error(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status of tftp session. When a session ended with success, the tftpStatus should be endedOk(6). Before restarting a tftp session, the modem should set the tftpStatus to noOp(2). Options: 1. noOp(1) - Indicates that no operation. 2. connecting(2) - Indicates that connecting. 3. transferringData(3) - Indicates that transferring data. 4. timeOut(4) - Indicates that time-out. 5. endedOk(5) - Indicates that end successfully. 6. error(6) - Indicates that error occur. " ::= { hwTdmTftpEntry 4 } -- -- ASMi52A Modem Information Table -- hwTdmModemInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF HwTdmModemInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM modem system information. This information describe the maximum rate, the PSD type, the interface type of the DTE port, the modem wiring, the actual ASMi52 type, the modem hardware version, the modem software version, IP address and MAC address.The index of this table is ifIndex." ::= { hwTdmModemObjects 1 } hwTdmModemInfoEntry OBJECT-TYPE SYNTAX HwTdmModemInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM modem system information. This information describe the maximum rate, the PSD type, the interface type of the DTE port, the modem wiring, the actual ASMi52 type, the modem hardware version, the modem software version, IP address and MAC address.The index of this entry is ifIndex." INDEX { ifIndex } ::= { hwTdmModemInfoTable 1 } HwTdmModemInfoEntry ::= SEQUENCE { hwTdmModemInfoDteIfType INTEGER, hwTdmModemInfoWireMode INTEGER, hwTdmModemInfoModemType INTEGER, hwTdmModemInfoHwVer OCTET STRING, hwTdmModemInfoSwVer OCTET STRING, hwTdmModemSupportEOC INTEGER, hwTdmModemLowerSpeedOper INTEGER, hwTdmModemDtePortState INTEGER, hwTdmModemE1PortState INTEGER } hwTdmModemInfoDteIfType OBJECT-TYPE SYNTAX INTEGER { x21(0), v35(1), v24(2), rs530(3), irETHQN(5), g703r64k(6), irHSSI(7), g704(8), irT1(28), g703(29), other(255) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the interface type of the DTE port. Options: 1. x21(0) - Indicates that the interface type of the DTE port is x21. 2. v35(1) - Indicates that the interface type of the DTE port is v35. 3. v24(2) - Indicates that the interface type of the DTE port is v24. 4. rs530(3) - Indicates that the interface type of the DTE port is rs530. 5. irETHQN(5) - Indicates that the interface type of the DTE port is irETHQN. 6. g703r64k(6) - Indicates that the interface type of the DTE port is g703r64k. 7. irHSSI(7) - Indicates that the interface type of the DTE port is irHSSI. 8. g704(8) - Indicates that the interface type of the DTE port is g704. 9. irT1(28) - Indicates that the interface type of the DTE port is irT1. 10. g703(29) - Indicates that the interface type of the DTE port is g703. 11. other(255) - Indicates that the interface type of the DTE port is other. " ::= { hwTdmModemInfoEntry 2 } hwTdmModemInfoWireMode OBJECT-TYPE SYNTAX INTEGER { twoWire(1), fourWire(2), notApplicable(255) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the modem wiring. Options: 1. twoWire(1) - Indicates that the modem wiring is twoWire. 2. fourWire(2) - Indicates that the modem wiring is fourWire. 3. notApplicable(255) - Indicates that the modem wiring isnotApplicable. " ::= { hwTdmModemInfoEntry 3 } hwTdmModemInfoModemType OBJECT-TYPE SYNTAX INTEGER { none(0), cardData(1), cardE1T1(2), cardDataE1(3), cardEthernet(4), cardDataEthernet(5), cardE1T1Ethernet(6), cardDataE1T1Ethernet(7), cardDataEthm(9), cardE1T1Ethm(10), cardDataE1Ethm(11), cardEthernetEthm(12), cardDataEthernetEthm(13), cardE1T1EthernetEthm(14), cardDataE1T1EthernetEthm(15) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the actual ASMi52 type. Options: 1. none(0) - Indicates that the actual ASMi52 type is none. 2. cardData(1) - Indicates that the actual ASMi52 type is cardData. 3. cardE1T1(2) - Indicates that the actual ASMi52 type is cardE1T1. 4. cardDataE1(3) - Indicates that the actual ASMi52 type is cardDataE1. 5. cardEthernet(4) - Indicates that the actual ASMi52 type is cardEthernet. 6. cardDataEthernet(5) - Indicates that the actual ASMi52 type is cardDataEthernet. 7. cardE1T1Ethernet(6) - Indicates that the actual ASMi52 type is cardE1T1Ethernet. 8. cardDataE1T1Ethernet(7) - Indicates that the actual ASMi52 type is cardDataE1T1Ethernet. 9. cardDataEthm(9) - Indicates that the actual ASMi52 type is cardDataEthm. 10. cardE1T1Ethm(10) - Indicates that the actual ASMi52 type is cardE1T1Ethm. 11. cardDataE1Ethm(11) - Indicates that the actual ASMi52 type is cardDataE1Ethm. 12. cardEthernetEthm(12) - Indicates that the actual ASMi52 type is cardEthernetEthm. 13. cardDataEthernetEthm(13) - Indicates that the actual ASMi52 type is cardDataEthernetEthm. 14. cardE1T1EthernetEthm(14) - Indicates that the actual ASMi52 type is cardE1T1EthernetEthm. 15. cardDataE1T1EthernetEthm(15) - Indicates that the actual ASMi52 type is cardDataE1T1EthernetEthm. " ::= { hwTdmModemInfoEntry 4 } hwTdmModemInfoHwVer OBJECT-TYPE SYNTAX OCTET STRING (SIZE(10)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the display string of the modem hardware version." ::= { hwTdmModemInfoEntry 5 } hwTdmModemInfoSwVer OBJECT-TYPE SYNTAX OCTET STRING (SIZE(10)) MAX-ACCESS read-only STATUS current DESCRIPTION "Display String of the modem software version. Examples: 2.23A8 3.4" ::= { hwTdmModemInfoEntry 6 } hwTdmModemSupportEOC OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the port supports the EOC or not. Options: 1. yes(1) - Indicates that the port supports the EOC. 2. no(2) - Indicates that the port does not support the EOC. " ::= { hwTdmModemInfoEntry 7 } hwTdmModemLowerSpeedOper OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2), na(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the modem run in lower speed or not. When you download file with V35 MODEM , it must be yes.If it is not, you can change it by reseting to factory or default configuration. In the case of E1 MODEM, it will return NA. Options: 1. yes(1) - Indicates that the modem run in lower speed. 2. no(2) - Indicates that the modem does not run in lower speed. 3. na(3) - NA. " ::= { hwTdmModemInfoEntry 8 } hwTdmModemDtePortState OBJECT-TYPE SYNTAX INTEGER { connect(1), disconnect(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the down port state. Options: 1. connect(1) - Indicates that the down port connected. 2. disconnect(2) - Indicates that the down port disconnected. " ::= { hwTdmModemInfoEntry 9 } hwTdmModemE1PortState OBJECT-TYPE SYNTAX INTEGER { connect(1), disconnect(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the down port state. Options: 1. connect(1) - Indicates that the down port connected. 2. disconnect(2) - Indicates that the down port disconnected. " ::= { hwTdmModemInfoEntry 10 } -- -- ASMi52A Modem Configuration Table -- hwTdmModemConfTable OBJECT-TYPE SYNTAX SEQUENCE OF HwTdmModemConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM Modem configuration that may be used with G.SHDSL modem for configuration. This information describe the alarm report mask, the port status report mask, the reset command, the switch to clear the alarm buffer, the switch to clear statistics of the selected port, test time out and test command. The index of this table is ifIndex." ::= { hwTdmModemObjects 2 } hwTdmModemConfEntry OBJECT-TYPE SYNTAX HwTdmModemConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM Modem configuration that may be used with G.SHDSL modem for configuration. This information describe the alarm report mask, the port status report mask, the reset command, the switch to clear the alarm buffer, the switch to clear statistics of the selected port, test time out and test command. The index of this entry is ifIndex." INDEX { ifIndex } ::= { hwTdmModemConfTable 1 } HwTdmModemConfEntry ::= SEQUENCE { hwTdmModemConfAlarmAndPortMask INTEGER, -- hwTdmModemConfPerformanceMask -- INTEGER, hwTdmModemConfReset INTEGER, hwTdmModemAlrBufClear INTEGER, hwTdmModemStatClear INTEGER, hwTdmModemAlarmDevSeverity OCTET STRING, hwTdmModemAlarmPortSeverity OCTET STRING -- hwTdmModemTestTimeout -- Integer32, -- hwTdmModemTestCmd -- INTEGER } hwTdmModemConfAlarmAndPortMask OBJECT-TYPE SYNTAX INTEGER { majorAlarmMask(1), minorAlarmMask(2), portMask(3), majorAndMinorMask(4), majorAndPortMask(5), minorAndPortMask(6), allMask(7), noMask(8) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "This value identifies the alarm and port status report mask of the TDM remote modem in the far-end side. Options: 1. majorAlarmMask(1) - Indicates that mask is majorAlarmMask. 2. minorAlarmMask(2) - Indicates that mask is minorAlarmMask. 3. portMask(3) - Indicates that mask is portMask. 4. majorAndMinorMask(4) - Indicates that mask is majorAndMinorMask. 5. majorAndPortMask(5) - Indicates that mask is majorAndPortMask. 6. minorAndPortMask(6) - Indicates that mask is minorAndPortMask. 7. allMask(7) - Indicates that mask is allMask. 8. noMask(8) - Indicates that mask is noMask. " DEFVAL { minorAndPortMask } ::= { hwTdmModemConfEntry 1 } -- hwTdmModemConfPerformanceMask OBJECT-TYPE -- SYNTAX INTEGER -- { -- on(1), -- off(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "This value identifies the performance report mask of the TDM remote modem -- in the far-end side. " -- DEFVAL { off } -- ::= { hwTdmModemConfEntry 3 } hwTdmModemConfReset OBJECT-TYPE SYNTAX INTEGER { off(2), resetToFactory(3), deviceReset(4), lineReset(5), resetConfigwoMng(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "This value identifies the reset command of the TDM remote modem in the far-end side. Changing this value can reset the device or the line, or set the configuration to factory setting. reset_config_wo_mng :set all parameters to default , instead of parameters of management : IP_address, IP_mask and etc Options: 1. off(2) - Indicates that do nothing. 2. resetToFactory(3) - Indicates that reset to factory. 3. deviceReset(4) - Indicates that device reset. 4. lineReset(5) - Indicates that line reset. 5. resetConfigwoMng(6) - Indicates that set all parameters to default. " DEFVAL { off } ::= { hwTdmModemConfEntry 2 } hwTdmModemAlrBufClear OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This value indicates the switch to clear the Alarm buffer in the remote modem. Options: 1. on(1) - Indicates that the switch is on. 2. off(2) - Indicates that the switch is off. " DEFVAL { off } ::= { hwTdmModemConfEntry 3 } hwTdmModemStatClear OBJECT-TYPE SYNTAX INTEGER { none(1), clearSHDSLA(2), clearSHDSLB(3), clearE1(4), clearAll(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "This value indicates resetting statistics of the selected port. Options: 1. none(1) - Indicates that do nothing. 2. clearSHDSLA(2) - Indicates that clear SHDSLA statistics. 3. clearSHDSLB(3) - Indicates that clear SHDSLB statistics. 4. clearE1(4) - Indicates that clear E1 statistics. 5. clearAll(5) - Indicates that clear all statistics. " DEFVAL { none } ::= { hwTdmModemConfEntry 4 } hwTdmModemAlarmDevSeverity OBJECT-TYPE SYNTAX OCTET STRING (SIZE(2)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the alarms severity device bit mapping. " ::= { hwTdmModemConfEntry 5 } hwTdmModemAlarmPortSeverity OBJECT-TYPE SYNTAX OCTET STRING (SIZE(12)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the alarms severity port bit mapping. " ::= { hwTdmModemConfEntry 6 } -- hwTdmModemTestTimeout OBJECT-TYPE -- SYNTAX Integer32 (0..4095) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "This object is applicable only when a single test is -- running. It indicates the test activation timeout in -- minutes. When the timeout expires, the test is stopped. -- Value of 0 indicates test may run Forever." -- DEFVAL { 0 } -- ::= { hwTdmModemConfEntry 7 } -- hwTdmModemTestCmd OBJECT-TYPE -- SYNTAX INTEGER -- { -- stop(1), -- rlbOnly(2), -- llbOnly(3), -- rlbAndLlb(4), -- reserved(5) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Setting this object to a value as detailed further on -- will initiate a test on the specific port. -- -- The terminology and order of the first tests is according -- to the one used for Test Status of DS1 and DS3 standards. -- The notations : RLB, LLB, DIG are the most used in RAD's -- products, but they can be different. For exact definition -- see product's spec. -- -- Setting this object to stop (value=1), will stop all the -- user requested tests running on the selected port. -- -- When no test is running on the port, the Get value (test status) -- will be stop(1). -- -- PayloadLoop=RLB (Remote Loopback) -- The received signal at this interface is looped -- through the device. Typically the received signal -- is looped back for retransmission after it has -- passed through the device's framing function. -- -- InwardLoop=LLB (Local Loopback) -- The sent signal at this interface is looped back -- through the device." -- DEFVAL { stop } -- ::= { hwTdmModemConfEntry 8 } -- -- ASMi52A Modem Alarm Buffer Table -- hwTdmModemAlarmBufTable OBJECT-TYPE SYNTAX SEQUENCE OF HwTdmModemAlarmBufEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM Modem alarm buffer that may be used for NMS polling. This information describe the alarm buffer index, the status of the alarm and severity of the alarm.The indexes of this table are ifIndex, hwTdmModemAlarmBufIndex." ::= { hwTdmModemObjects 3 } hwTdmModemAlarmBufEntry OBJECT-TYPE SYNTAX HwTdmModemAlarmBufEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM Modem alarm buffer that may be used for NMS polling. This information describe the alarm buffer index, the status of the alarm and severity of the alarm.The indexes of this entry are ifIndex, hwTdmModemAlarmBufIndex." INDEX { ifIndex, hwTdmModemAlarmBufIndex } ::= { hwTdmModemAlarmBufTable 1 } HwTdmModemAlarmBufEntry ::= SEQUENCE { hwTdmModemAlarmBufIndex Integer32, hwTdmModemAlarmBufCode Integer32, hwTdmModemAlarmBufState INTEGER, hwTdmModemAlarmBufSeverity INTEGER } hwTdmModemAlarmBufIndex OBJECT-TYPE SYNTAX Integer32 (1..100) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This value indicates the alarm buffer index in the modem." ::= { hwTdmModemAlarmBufEntry 1 } hwTdmModemAlarmBufCode OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The code of the alarm. For text description of each Alarm code see Modem's specification." ::= { hwTdmModemAlarmBufEntry 2 } hwTdmModemAlarmBufState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The new status of the alarm. Options: 1. on(1) - Indicates that the alarm is on. 2. off(2) - Indicates that the alarm is off. " ::= { hwTdmModemAlarmBufEntry 3 } hwTdmModemAlarmBufSeverity OBJECT-TYPE SYNTAX INTEGER { major(1), minor(2), warning(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The severity of the alarm. Options: 1. major(1) - Indicates that the alarm is major. 2. minor(2) - Indicates that the alarm is minor. 3. warning(3) - Indicates that the alarm is warning. " ::= { hwTdmModemAlarmBufEntry 4 } -- -- ASMi52A SHDSL Port Configuration Table -- hwTdmShdslConfTable OBJECT-TYPE SYNTAX SEQUENCE OF HwTdmShdslConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the information about a TDM Modem SHDSL port configuration. This information describe the SHDSL port index, power backoff mode, worst case target SNR margin, current condition target SNR margin, PSD (Power Spectral Density) Mask, line probe mode, the loop attenuation alarm threshold, the SNR margin alarm threshold ,the line wiring, the test timeout and test cmd.The index of this table is ifIndex." ::= { hwTdmPortConfObjects 1 } hwTdmShdslConfEntry OBJECT-TYPE SYNTAX HwTdmShdslConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the information about a TDM Modem SHDSL port configuration. This information describe the SHDSL port index, power backoff mode, worst case target SNR margin, current condition target SNR margin, PSD (Power Spectral Density) Mask, line probe mode, the loop attenuation alarm threshold, the SNR margin alarm threshold ,the line wiring, the test timeout and test cmd.The index of this entry is ifIndex." INDEX { ifIndex } ::= { hwTdmShdslConfTable 1 } HwTdmShdslConfEntry ::= SEQUENCE { hwTdmShdslConfPowerBackOff INTEGER, hwTdmShdslConfWorstCaseSNRMargin Integer32, hwTdmShdslConfCurrentSNRMargin Integer32, hwTdmShdslConfPSD INTEGER, hwTdmShdslConfLineProbe INTEGER, hwTdmShdslConfThreshLoopAttenuation Integer32, hwTdmShdslConfThreshSNRMargin Integer32, hwTdmShdslConfWireInterface INTEGER, hwTdmShdslConfTestTimeout Integer32, hwTdmShdslConfTestCmd INTEGER } hwTdmShdslConfPowerBackOff OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object configures the receiver at the associated segment endpoint to operate in power backoff mode. Options: 1. enable(1) - Indicates that enable the function. 2. disable(2) - Indicates that disable the function. " ::= { hwTdmShdslConfEntry 1 } hwTdmShdslConfWorstCaseSNRMargin OBJECT-TYPE SYNTAX Integer32 (-10..11) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the upstream worst case target SNR margin for a SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the desired SNR margin for a unit. The normal value is from -10 to 10 , 11 means DSP chip HANDSHAKE not used this parameters" ::= { hwTdmShdslConfEntry 2 } hwTdmShdslConfCurrentSNRMargin OBJECT-TYPE SYNTAX Integer32 (-10..11) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the upstream current condition target SNR margin for a SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the desired SNR margin for a unit. The normal value is from -10 to 10 , 11 means DSP chip HANDSHAKE not used this parameters" ::= { hwTdmShdslConfEntry 3 } hwTdmShdslConfPSD OBJECT-TYPE SYNTAX INTEGER { asymDisable(0), asymEnable(1), r1AsymEnable(2), r2AsymEnable(3), asymSymEnable(4), psdUnknown(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object configures use of symmetric/asymmetric PSD (Power Spectral Density) Mask for the associated SHDSL Line. Support for symmetric PSD is mandatory for all supported data rates. Support for asymmetric PSD is optional. Options: 1. asymDisable(0) - Indicates that PSD asymmetric disable. 2. asymEnable(1) - Indicates that PSD asymmetric enable. 3. r1AsymEnable(2) - Indicates that PSD r1 asymmetric enable. 4. r2AsymEnable(3) - Indicates that PSD r2 asymmetric enable. 5. asymSymEnable(4) - Indicates that PSD asymmetric and symmetric enable. 6. psdUnknown(5) - Indicates that PSD unknown. " ::= { hwTdmShdslConfEntry 4 } hwTdmShdslConfLineProbe OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object enables/disables support for Line Probe of the units in a SHDSL line. When Line Probe is enabled, the system performs Line Probing to find the best possible rate (adaptive rate). If Line probe is disabled, the rate adaptation phase is skipped to shorten set up time (fixed rate). Options: 1. enable(1) - Indicates that enable the function. 2. disable(2) - Indicates that disable the function. " ::= { hwTdmShdslConfEntry 5 } hwTdmShdslConfThreshLoopAttenuation OBJECT-TYPE SYNTAX Integer32 (0..127) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "This object configures the loop attenuation alarm threshold." DEFVAL { 0 } ::= { hwTdmShdslConfEntry 6 } hwTdmShdslConfThreshSNRMargin OBJECT-TYPE SYNTAX Integer32 (0..15) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "This object configures the SNR margin alarm threshold." DEFVAL { 0 } ::= { hwTdmShdslConfEntry 7 } hwTdmShdslConfWireInterface OBJECT-TYPE SYNTAX INTEGER { twoWire(1), fourWire(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object configures the two-wire or optional four-wire operation for SHDSL Lines. Options: 1. twoWire(1) - Indicates that the operation for SHDSL Lines is two-wire. 2. fourWire(2) - Indicates that the operation for SHDSL Lines is four-wire. " DEFVAL { twoWire } ::= { hwTdmShdslConfEntry 8 } hwTdmShdslConfTestTimeout OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is applicable only when a single test is running. It indicates the test activation timeout in minutes. When the timeout expires, the test is stopped. Value of 0 indicates test may run Forever." DEFVAL { 5 } ::= { hwTdmShdslConfEntry 9 } hwTdmShdslConfTestCmd OBJECT-TYPE SYNTAX INTEGER { stop(1), gsrLb(2), dteRlb(3), e1Rlb(4), otherloop(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to a value as detailed further on will initiate a test on the specific port. The terminology and order of the first tests is according to the one used for Test Status of DS1 and DS3 standards. The notations : RLB, LLB, DIG are the most used in RAD's products, but they can be different. For exact definition see product's spec. Setting this object to stop (value=1), will stop all the user requested tests running on the selected port. When no test is running on the port, the Get value (test status) will be stop(1). PayloadLoop=RLB (Remote Loopback) The received signal at this interface is looped through the device. Typically the received signal is looped back for retransmission after it has passed through the device's framing function. InwardLoop=LLB (Local Loopback) The sent signal at this interface is looped back through the device. Options: 1. stop(1) - Indicates that stop all the user requested tests running on the selected port. 2. gsrLb(2) - Indicates that initiate gsrLb test. 3. dteRlb(3) - Indicates that initiate dteRlb test . 4. e1Rlb(4) - Indicates that initiate e1Rlb test. 5. otherloop(5) - Indicates that initiate otherloop test. " DEFVAL { stop } ::= { hwTdmShdslConfEntry 10 } -- -- ASMi52A E1/T1 Port Configuration Table -- hwTdmE1ConfTable OBJECT-TYPE SYNTAX SEQUENCE OF HwTdmE1ConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM Modem E1 port configuration. This information describe the E1 port index, line type, sync, idelcode and crc4 value. The index of this table is ifIndex." ::= { hwTdmPortConfObjects 2 } hwTdmE1ConfEntry OBJECT-TYPE SYNTAX HwTdmE1ConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM Modem E1 port configuration. This information describe the E1 port index, line type, sync, idelcode and crc4 value. The index of this entry is ifIndex." INDEX { ifIndex } ::= { hwTdmE1ConfTable 1 } HwTdmE1ConfEntry ::= SEQUENCE { hwTdmE1ConfLineType INTEGER, hwTdmE1ConfSync INTEGER, hwTdmE1ConfIdleCode Integer32, hwTdmE1ConfCrc4 INTEGER } hwTdmE1ConfLineType OBJECT-TYPE SYNTAX INTEGER { esf(0), d4(1), e1(2), e1MF(3), unframed(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable indicates the variety of T1/E1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reasonably carry, as well as the interpretation of the usage and error statistics. The values, in sequence, describe: TITLE: SPECIFICATION: esf Extended SuperFrame DS1 d4 AT&T D4 format DS1 - SF e1 CCITT Recommendation G.704 (Table 4a) - G732N e1MF G.704 (Table 4a) with TS16 multiframing enabled - G732S unframed Options: 1. esf(0) - Indicates that the variety is esf. 2. d4(1) - Indicates that the variety is d4. 3. e1(2) - Indicates that the variety is e1. 4. e1MF(3) - Indicates that the variety is e1MF. 5. unframed(4) - Indicates that the variety is unframed. " ::= { hwTdmE1ConfEntry 1 } hwTdmE1ConfSync OBJECT-TYPE SYNTAX INTEGER { fast(1), tr62411(2), ccitt(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object enables returning to normal operation, after the end of a main/sub link red alarm event, in reduced time. 'tr62411' - complies with AT&T TR-62411 (after 10 seconds). Applicable for both T1 and E1 interfaces. 'ccitt' - complies with CCITT standard. Applicable only for E1 interfaces. 'fast' - after 1 second. Options: 1. fast(1) - Indicates that return to normal operation in fast mode. 2. tr62411(2) - Indicates that return to normal operation in tr62411 mode. 3. ccitt(3) - Indicates that return to normal operation in ccitt mode. " ::= { hwTdmE1ConfEntry 2 } hwTdmE1ConfIdleCode OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "This object selects the code transmitted to fill idle (unused) time slots in the main link frame. Valid range: (0 - FF HEX)." ::= { hwTdmE1ConfEntry 3 } -- hwTdmE1ConfSameFeCnfg OBJECT-TYPE -- SYNTAX INTEGER -- { -- notApplicable(1), -- no(2), -- yes(3) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "This parameter indicates whether the same E1 configuration -- parameters and TS assignment are set both to the local -- and remote device. -- Read-Write access is applicable only in G732N framed mode. -- For G732S and UNFRAMED this parameter is set by -- agent to YES and is Read Only. -- In Case of conflict during power-up between the central -- and remote, the value set by the central unit is the valid one." -- ::= { hwTdmE1ConfEntry 4 } hwTdmE1ConfCrc4 OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter indicates whether the CRC-4 is set to the local and remote device. Options: 1. yes(1) - Indicates that set CRC-4. 2. no(2) - Indicates that no set CRC-4. " DEFVAL { no } ::= { hwTdmE1ConfEntry 4 } -- -- ASMi52A DTE Port Configuration Table -- hwTdmDTEConfTable OBJECT-TYPE SYNTAX SEQUENCE OF HwTdmDTEConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the information about a TDM Modem DTE port configuration. This information describe the DTE port index, local analog loop-back switch, remote loop-back switch, and Ir rate.The index of this table is ifIndex." ::= { hwTdmPortConfObjects 3 } hwTdmDTEConfEntry OBJECT-TYPE SYNTAX HwTdmDTEConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the information about a TDM Modem DTE port configuration. This information describe the DTE port index, local analog loop-back switch, remote loop-back switch, and Ir rate.The index of this entry is ifIndex." INDEX { ifIndex } ::= { hwTdmDTEConfTable 1 } HwTdmDTEConfEntry ::= SEQUENCE { hwTdmDTEConfLlbEnable INTEGER, hwTdmDTEConfRlbEnable INTEGER, hwTdmDTEConfIrRate INTEGER } hwTdmDTEConfLlbEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable local Analog Loop-Back on this modem, externally initiated. Options: 1. enable(1) - Indicates that enable the function. 2. disable(2) - Indicates that disable the function. " ::= { hwTdmDTEConfEntry 1 } hwTdmDTEConfRlbEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Remote Loop-Back on this modem, externally initiated. Options: 1. enable(1) - Indicates that enable the function. 2. disable(2) - Indicates that disable the function. " ::= { hwTdmDTEConfEntry 2 } hwTdmDTEConfIrRate OBJECT-TYPE SYNTAX INTEGER { r64Kbps(1), r128Kbps(2), r192Kbps(3), r256Kbps(4), r320Kbps(5), r384Kbps(6), r448Kbps(7), r512Kbps(8), r576Kbps(9), r640Kbps(10), r704Kbps(11), r768Kbps(12), r832Kbps(13), r896Kbps(14), r960Kbps(15), r1024Kbps(16), r1088Kbps(17), r1152Kbps(18), r1216Kbps(19), r1280Kbps(20), r1344Kbps(21), r1408Kbps(22), r1472Kbps(23), r1536Kbps(24), r1600Kbps(25), r1664Kbps(26), r1728Kbps(27), r1792Kbps(28), r1856Kbps(29), r1920Kbps(30), r1984Kbps(31), r2048Kbps(32), r2112Kbps(33), r2176Kbps(34), r2240Kbps(35), r2304Kbps(36), r2432Kbps(37), r2560Kbps(38), r2688Kbps(39), r2816Kbps(40), r2944Kbps(41), r3072Kbps(42), r3200Kbps(43), r3328Kbps(44), r3456Kbps(45), r3584Kbps(46), r3712Kbps(47), r3840Kbps(48), r3968Kbps(49), r4096Kbps(50), r4224Kbps(51), r4352Kbps(52), r4480Kbps(53), r4608Kbps(54), notApplicable(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the DTE port rate.for mux device.When modem is two_wire model,its max supported value is 2048Kbps. Options: 1, r64Kbps(1) - Indicates the DTE port rate is r64Kbps. 2, r128Kbps(2) - Indicates the DTE port rate is r128Kbps. 3, r192Kbps(3) - Indicates the DTE port rate is r192Kbps. 4, r256Kbps(4) - Indicates the DTE port rate is r256Kbps. 5, r320Kbps(5) - Indicates the DTE port rate is r320Kbps. 6, r384Kbps(6) - Indicates the DTE port rate is r384Kbps. 7, r448Kbps(7) - Indicates the DTE port rate is r448Kbps. 8, r512Kbps(8) - Indicates the DTE port rate is r512Kbps. 9, r576Kbps(9) - Indicates the DTE port rate is r576Kbps. 10, r640Kbps(10) - Indicates the DTE port rate is r640Kbps. 11, r704Kbps(11) - Indicates the DTE port rate is r704Kbps. 12, r768Kbps(12) - Indicates the DTE port rate is r768Kbps. 13, r832Kbps(13) - Indicates the DTE port rate is r832Kbps. 14, r896Kbps(14) - Indicates the DTE port rate is r896Kbps. 15, r960Kbps(15) - Indicates the DTE port rate is r960Kbps. 16, r1024Kbps(16) - Indicates the DTE port rate is r1024Kbps. 17, r1088Kbps(17) - Indicates the DTE port rate is r1088Kbps. 18, r1152Kbps(18) - Indicates the DTE port rate is r1152Kbps. 19, r1216Kbps(19) - Indicates the DTE port rate is r1216Kbps. 20, r1280Kbps(20) - Indicates the DTE port rate is r1280Kbps. 21, r1344Kbps(21) - Indicates the DTE port rate is r1344Kbps. 22, r1408Kbps(22) - Indicates the DTE port rate is r1408Kbps. 23, r1472Kbps(23) - Indicates the DTE port rate is r1472Kbps. 24, r1536Kbps(24) - Indicates the DTE port rate is r1536Kbps. 25, r1600Kbps(25) - Indicates the DTE port rate is r1600Kbps. 26, r1664Kbps(26) - Indicates the DTE port rate is r1664Kbps. 27, r1728Kbps(27) - Indicates the DTE port rate is r1728Kbps. 28, r1792Kbps(28) - Indicates the DTE port rate is r1792Kbps. 29, r1856Kbps(29) - Indicates the DTE port rate is r1856Kbps. 30, r1920Kbps(30) - Indicates the DTE port rate is r1920Kbps. 31, r1984Kbps(31) - Indicates the DTE port rate is r1984Kbps. 32, r2048Kbps(32) - Indicates the DTE port rate is r2048Kbps. 33, r2112Kbps(33) - Indicates the DTE port rate is r2112Kbps. 34, r2176Kbps(34) - Indicates the DTE port rate is r2176Kbps. 35, r2240Kbps(35) - Indicates the DTE port rate is r2240Kbps. 36, r2304Kbps(36) - Indicates the DTE port rate is r2304Kbps. 37, r2432Kbps(37) - Indicates the DTE port rate is r2432Kbps. 38, r2560Kbps(38) - Indicates the DTE port rate is r2560Kbps. 39, r2688Kbps(39) - Indicates the DTE port rate is r2688Kbps. 40, r2816Kbps(40) - Indicates the DTE port rate is r2816Kbps. 41, r2944Kbps(41) - Indicates the DTE port rate is r2944Kbps. 42, r3072Kbps(42) - Indicates the DTE port rate is r3072Kbps. 43, r3200Kbps(43) - Indicates the DTE port rate is r3200Kbps. 44, r3328Kbps(44) - Indicates the DTE port rate is r3328Kbps. 45, r3456Kbps(45) - Indicates the DTE port rate is r3456Kbps. 46, r3584Kbps(46) - Indicates the DTE port rate is r3584Kbps. 47, r3712Kbps(47) - Indicates the DTE port rate is r3712Kbps. 48, r3840Kbps(48) - Indicates the DTE port rate is r3840Kbps. 49, r3968Kbps(49) - Indicates the DTE port rate is r3968Kbps. 50, r4096Kbps(50) - Indicates the DTE port rate is r4096Kbps. 51, r4224Kbps(51) - Indicates the DTE port rate is r4224Kbps. 52, r4352Kbps(52) - Indicates the DTE port rate is r4352Kbps. 53, r4480Kbps(53) - Indicates the DTE port rate is r4480Kbps. 54, r4608Kbps(54) - Indicates the DTE port rate is r4608Kbps. 55, notApplicable(255) - Indicates the DTE port rate is notApplicable. " ::= { hwTdmDTEConfEntry 3 } -- ASMi52A G.SHDSL Port current statistics Table including 15 minute interval and 24 hour interval hwTdmShdslCurrentStatTable OBJECT-TYPE SYNTAX SEQUENCE OF HwTdmShdslCurrentStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM Modem SHDSL port statistics including 15 minute and 1 day interval. This information describe total elapsed seconds, the number of errored seconds, the number of unavailable seconds, the number of severely errored seconds, the number of CRC anomalies, the number of loss of sync word seconds. The indexes of this table are ifIndex, hwTdmShdslLineIndex." ::= { hwTdmPortStatObjects 1 } hwTdmShdslCurrentStatEntry OBJECT-TYPE SYNTAX HwTdmShdslCurrentStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM Modem SHDSL port statistics including 15 minute and 1 day interval. This information describe total elapsed seconds, the number of errored seconds, the number of unavailable seconds, the number of severely errored seconds, the number of CRC anomalies, the number of loss of sync word seconds. The indexes of this entry are ifIndex, hwTdmShdslLineIndex." INDEX { ifIndex, hwTdmShdslLineIndex } ::= { hwTdmShdslCurrentStatTable 1 } HwTdmShdslCurrentStatEntry ::= SEQUENCE { hwTdmShdslLineIndex INTEGER, hwTdmShdslCurrentTimeElapsed Unsigned32, hwTdmShdslCurrent15MinES Gauge32, hwTdmShdslCurrent15MinSES Gauge32, hwTdmShdslCurrent15MinCRCanomalies Gauge32, hwTdmShdslCurrent15MinLOSWS Gauge32, hwTdmShdslCurrent15MinUAS Gauge32, -- hwTdmShdslCurrent15MinLoswErrors -- Gauge32, hwTdmShdslCurrent1DayES Gauge32, hwTdmShdslCurrent1DaySES Gauge32, hwTdmShdslCurrent1DayCRCanomalies Gauge32, hwTdmShdslCurrent1DayLOSWS Gauge32, hwTdmShdslCurrent1DayUAS Gauge32, -- hwTdmShdslCurrent1DayLoswErrors -- Gauge32, hwTdmShdslCurrentSNRMargin Integer32, hwTdmShdslCurrentLoopAttenuation Integer32, -- hwTdmShdslCurrentRcvGain -- Integer32, hwTdmShdslCurrentTransPower Integer32, hwTdmShdslCurrentPowerBO Integer32 } hwTdmShdslLineIndex OBJECT-TYPE SYNTAX INTEGER { lineA(1), lineB(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "This value indicates the SHDSL line port index. Options: 1. lineA(1) - Indicates the SHDSL line port index is lineA. 2. lineB(2) - Indicates the SHDSL line port index is lineB. " ::= { hwTdmShdslCurrentStatEntry 1 } hwTdmShdslCurrentTimeElapsed OBJECT-TYPE SYNTAX Unsigned32 (0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in the current interval." ::= { hwTdmShdslCurrentStatEntry 2 } hwTdmShdslCurrent15MinES OBJECT-TYPE SYNTAX Gauge32 (0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds (ES) in the current 15-minute interval." ::= { hwTdmShdslCurrentStatEntry 3 } hwTdmShdslCurrent15MinSES OBJECT-TYPE SYNTAX Gauge32 (0..900) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Severely Errored Seconds (SES) in the current 15-minute interval. when sync is off ,it may be 900" ::= { hwTdmShdslCurrentStatEntry 4 } hwTdmShdslCurrent15MinCRCanomalies OBJECT-TYPE SYNTAX Gauge32 UNITS "detected CRC Anomalies" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of CRC anomalies in the current 15-minute interval." ::= { hwTdmShdslCurrentStatEntry 5 } hwTdmShdslCurrent15MinLOSWS OBJECT-TYPE SYNTAX Gauge32 (0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Sync Word (LOSW) Seconds in the current 15-minute interval." ::= { hwTdmShdslCurrentStatEntry 6 } hwTdmShdslCurrent15MinUAS OBJECT-TYPE SYNTAX Gauge32 (0..900) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Unavailable Seconds (UAS) in the current 15-minute interval. when sync is off ,it may be 900" ::= { hwTdmShdslCurrentStatEntry 7 } -- hwTdmShdslCurrent15MinLoswErrors OBJECT-TYPE -- SYNTAX Gauge32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Count of LOSW errors in the current 15-minute interval." -- ::= { hwTdmShdslCurrentStatEntry 8 } hwTdmShdslCurrent1DayES OBJECT-TYPE SYNTAX Gauge32 (0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds (ES) in the current day interval." ::= { hwTdmShdslCurrentStatEntry 8 } hwTdmShdslCurrent1DaySES OBJECT-TYPE SYNTAX Gauge32 (0..86400) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Severely Errored Seconds (SES) in the current day interval." ::= { hwTdmShdslCurrentStatEntry 9 } hwTdmShdslCurrent1DayCRCanomalies OBJECT-TYPE SYNTAX Gauge32 UNITS "detected CRC Anomalies" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of CRC anomalies in the current day interval." ::= { hwTdmShdslCurrentStatEntry 10 } hwTdmShdslCurrent1DayLOSWS OBJECT-TYPE SYNTAX Gauge32 (0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Sync Word (LOSW) Seconds in the current day interval." ::= { hwTdmShdslCurrentStatEntry 11 } hwTdmShdslCurrent1DayUAS OBJECT-TYPE SYNTAX Gauge32 (0..86400) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Unavailable Seconds (UAS) in the current day interval." ::= { hwTdmShdslCurrentStatEntry 12 } -- hwTdmShdslCurrent1DayLoswErrors OBJECT-TYPE -- SYNTAX Gauge32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Count of LOSW errors in the current 24-hour interval." -- ::= { hwTdmShdslCurrentStatEntry 14 } hwTdmShdslCurrentSNRMargin OBJECT-TYPE SYNTAX Integer32 (0..15) UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "The current SNR margin for this endpoint as reported in a Status Response/SNR message." ::= { hwTdmShdslCurrentStatEntry 13 } hwTdmShdslCurrentLoopAttenuation OBJECT-TYPE SYNTAX Integer32 (0..127) UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "The current loop attenuation for this endpoint as reported in a Network or Customer Side Performance Status message." ::= { hwTdmShdslCurrentStatEntry 14 } -- hwTdmShdslCurrentRcvGain OBJECT-TYPE -- SYNTAX Integer32 -- UNITS "dB" -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The current receive gain in hundredth of dB." -- ::= { hwTdmShdslCurrentStatEntry 15 } hwTdmShdslCurrentTransPower OBJECT-TYPE SYNTAX Integer32 UNITS "dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "The current transmit power in tenth of dBm." ::= { hwTdmShdslCurrentStatEntry 15 } hwTdmShdslCurrentPowerBO OBJECT-TYPE SYNTAX Integer32 (0..6) UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "The current transceiver actual power packoff from 0dB to 6dB." ::= { hwTdmShdslCurrentStatEntry 16 } -- -- ASMi52A G.SHDSL Port statistics Table in 15 minute interval -- hwTdmShdslIntervalStatTable OBJECT-TYPE SYNTAX SEQUENCE OF HwTdmShdslIntervalStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM Modem SHDSL port statistics in 15 minute interval. This information describe the SHDSL port interval index, the number of errored seconds, the number of unavailable seconds, the number of severely errored seconds, the number of CRC anomalies and the number of loss of sync word seconds. The indexes of this table are ifIndex, hwTdmShdslLineIndex, hwTdmShdslIntervalIndex." ::= { hwTdmPortStatObjects 2 } hwTdmShdslIntervalStatEntry OBJECT-TYPE SYNTAX HwTdmShdslIntervalStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM Modem SHDSL port statistics in 15 minute interval. This information describe the SHDSL port interval index, the number of errored seconds, the number of unavailable seconds, the number of severely errored seconds, the number of CRC anomalies and the number of loss of sync word seconds. The indexes of this entry are ifIndex, hwTdmShdslLineIndex, hwTdmShdslIntervalIndex." INDEX { ifIndex, hwTdmShdslLineIndex, hwTdmShdslIntervalIndex } ::= { hwTdmShdslIntervalStatTable 1 } HwTdmShdslIntervalStatEntry ::= SEQUENCE { hwTdmShdslIntervalIndex Integer32, hwTdmShdslIntervalES Gauge32, hwTdmShdslIntervalSES Gauge32, hwTdmShdslIntervalCRCanomalies Gauge32, hwTdmShdslIntervalLOSWS Gauge32, hwTdmShdslIntervalUAS Gauge32 -- hwTdmShdslIntervalLoswErrors -- Gauge32 } hwTdmShdslIntervalIndex OBJECT-TYPE SYNTAX Integer32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This value indicates the interval SHDSL port statistics index in the remote modem." ::= { hwTdmShdslIntervalStatEntry 1 } hwTdmShdslIntervalES OBJECT-TYPE SYNTAX Gauge32 (0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds (ES) in 15-minute interval." ::= { hwTdmShdslIntervalStatEntry 2 } hwTdmShdslIntervalSES OBJECT-TYPE SYNTAX Gauge32 (0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Severely Errored Seconds (SES) in 15-minute interval. when sync is off ,it may be 900" ::= { hwTdmShdslIntervalStatEntry 3 } hwTdmShdslIntervalCRCanomalies OBJECT-TYPE SYNTAX Gauge32 UNITS "detected CRC Anomalies" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of CRC anomalies in 15-minute interval." ::= { hwTdmShdslIntervalStatEntry 4 } hwTdmShdslIntervalLOSWS OBJECT-TYPE SYNTAX Gauge32 (0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Sync Word (LOSW) Seconds in 15-minute interval." ::= { hwTdmShdslIntervalStatEntry 5 } hwTdmShdslIntervalUAS OBJECT-TYPE SYNTAX Gauge32 (0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Unavailable Seconds (UAS) in 15-minute interval. when sync is off ,it may be 900" ::= { hwTdmShdslIntervalStatEntry 6 } -- hwTdmShdslIntervalLoswErrors OBJECT-TYPE -- SYNTAX Gauge32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Count of LOSW errors in 15-minute interval." -- ::= { hwTdmShdslIntervalStatEntry 7 } -- -- ASMi52A G.SHDSL Port statistics Table in 1-day interval -- hwTdmShdslTotalStatTable OBJECT-TYPE SYNTAX SEQUENCE OF HwTdmShdslTotalStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM Modem SHDSL port statistics in 1-day interval. This information describe the SHDSL port interval index, the number of errored seconds, the number of unavailable seconds, the number of severely errored seconds, the number of CRC anomalies and the number of loss of sync word seconds. The indexes of this table are ifIndex, hwTdmShdslLineIndex, hwTdmShdslTotalIndex." ::= { hwTdmPortStatObjects 3 } hwTdmShdslTotalStatEntry OBJECT-TYPE SYNTAX HwTdmShdslTotalStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM Modem SHDSL port statistics in 1-day interval. This information describe the SHDSL port interval index, the number of errored seconds, the number of unavailable seconds, the number of severely errored seconds, the number of CRC anomalies and the number of loss of sync word seconds. The indexes of this entry are ifIndex, hwTdmShdslLineIndex, hwTdmShdslTotalIndex." INDEX { ifIndex, hwTdmShdslLineIndex, hwTdmShdslTotalIndex } ::= { hwTdmShdslTotalStatTable 1 } HwTdmShdslTotalStatEntry ::= SEQUENCE { hwTdmShdslTotalIndex Integer32, hwTdmShdslTotalES Gauge32, hwTdmShdslTotalSES Gauge32, hwTdmShdslTotalCRCanomalies Gauge32, hwTdmShdslTotalLOSWS Gauge32, hwTdmShdslTotalUAS Gauge32 -- hwTdmShdslTotalLoswErrors -- Gauge32 } hwTdmShdslTotalIndex OBJECT-TYPE SYNTAX Integer32 (1..7) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This value indicates the total SHDSL port statistics index in the remote modem." ::= { hwTdmShdslTotalStatEntry 1 } hwTdmShdslTotalES OBJECT-TYPE SYNTAX Gauge32 (0..86304) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds (ES) in 1-day interval." ::= { hwTdmShdslTotalStatEntry 2 } hwTdmShdslTotalSES OBJECT-TYPE SYNTAX Gauge32 (0..86400) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Severely Errored Seconds (SES) in 1-day interval." ::= { hwTdmShdslTotalStatEntry 3 } hwTdmShdslTotalCRCanomalies OBJECT-TYPE SYNTAX Gauge32 UNITS "detected CRC Anomalies" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of CRC anomalies in 1-day interval." ::= { hwTdmShdslTotalStatEntry 4 } hwTdmShdslTotalLOSWS OBJECT-TYPE SYNTAX Gauge32 (0..86304) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Loss of Sync Word (LOSW) Seconds in 1-day interval." ::= { hwTdmShdslTotalStatEntry 5 } hwTdmShdslTotalUAS OBJECT-TYPE SYNTAX Gauge32 (0..86400) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Unavailable Seconds (UAS) in 1-day interval." ::= { hwTdmShdslTotalStatEntry 6 } -- hwTdmShdslTotalLoswErrors OBJECT-TYPE -- SYNTAX Gauge32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Count of LOSW errors in 1-day interval." -- ::= { hwTdmShdslTotalStatEntry 7 } -- -- ASMi52A E1 Port statistics in current 15 minute interval Table -- hwTdmE1CurrentStatTable OBJECT-TYPE SYNTAX SEQUENCE OF HwTdmE1CurrentStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM Modem E1 port statistics in current 15 minute interval. This information describe the E1 port current interval index, the number of BPV (BiPolar Violation) events detected during the last minute, the maximal number of BPV (BiPolar Violation) events (per minute) detected during the worst minute, the number of CRC error events, the average number of CRC error events per second, the number of errored seconds, the number of unavailable seconds, the number of severely errored seconds, the number of bursty errored seconds, the number of loss of frame events, the number of controlled slip seconds, the number of degraded minutes and the number of seconds that have elapsed since the beginning of the near end current error- measurement period. The index of this table is ifIndex." ::= { hwTdmPortStatObjects 4 } hwTdmE1CurrentStatEntry OBJECT-TYPE SYNTAX HwTdmE1CurrentStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM Modem E1 port statistics in current 15 minute interval. This information describe the E1 port current interval index, the number of BPV (BiPolar Violation) events detected during the last minute, the maximal number of BPV (BiPolar Violation) events (per minute) detected during the worst minute, the number of CRC error events, the average number of CRC error events per second, the number of errored seconds, the number of unavailable seconds, the number of severely errored seconds, the number of bursty errored seconds, the number of loss of frame events, the number of controlled slip seconds, the number of degraded minutes and the number of seconds that have elapsed since the beginning of the near end current error- measurement period. The index of this entry is ifIndex." INDEX { ifIndex } ::= { hwTdmE1CurrentStatTable 1 } HwTdmE1CurrentStatEntry ::= SEQUENCE { hwTdmE1CurrentBpvLastMin Gauge32, hwTdmE1CurrentBpvMax Gauge32, hwTdmE1CurrentCRCErrorEvents Gauge32, hwTdmE1CurrentCRCAvgError Gauge32, hwTdmE1CurrentESs Gauge32, hwTdmE1CurrentUASs Gauge32, hwTdmE1CurrentSESs Gauge32, hwTdmE1CurrentBESs Gauge32, hwTdmE1CurrentLOFC Gauge32, hwTdmE1CurrentCSSs Gauge32, hwTdmE1CurrentDMs Gauge32, hwTdmE1TimeElapsed Gauge32 } hwTdmE1CurrentBpvLastMin OBJECT-TYPE SYNTAX Gauge32 (0..1000) MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the number of BPV (BiPolar Violation) events detected during the last minute." ::= { hwTdmE1CurrentStatEntry 1 } hwTdmE1CurrentBpvMax OBJECT-TYPE SYNTAX Gauge32 (0..1000) MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the maximal number of BPV (BiPolar Violation) events (per minute) detected during the worst minute." ::= { hwTdmE1CurrentStatEntry 2 } hwTdmE1CurrentCRCErrorEvents OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Counts the number of CRC error events, encountered in the current 15 minute interval." ::= { hwTdmE1CurrentStatEntry 3 } hwTdmE1CurrentCRCAvgError OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Counts the average number of CRC error events per second. The average is updated every second." ::= { hwTdmE1CurrentStatEntry 4 } hwTdmE1CurrentESs OBJECT-TYPE SYNTAX Gauge32 (0..899) MAX-ACCESS read-only STATUS current DESCRIPTION "Counts the number of errored seconds measured encountered in the current 15 minute interval." ::= { hwTdmE1CurrentStatEntry 5 } hwTdmE1CurrentUASs OBJECT-TYPE SYNTAX Gauge32 (0..900) MAX-ACCESS read-only STATUS current DESCRIPTION "Counts the number of unavailable seconds measured encountered in the current 15 minute interval." ::= { hwTdmE1CurrentStatEntry 6 } hwTdmE1CurrentSESs OBJECT-TYPE SYNTAX Gauge32 (0..900) MAX-ACCESS read-only STATUS current DESCRIPTION "Counts the number of severely errored seconds measured encountered in the current 15 minute interval." ::= { hwTdmE1CurrentStatEntry 7 } hwTdmE1CurrentBESs OBJECT-TYPE SYNTAX Gauge32 (0..899) MAX-ACCESS read-only STATUS current DESCRIPTION "Counts the number of bursty errored seconds measured encountered in the current 15 minute interval." ::= { hwTdmE1CurrentStatEntry 8 } hwTdmE1CurrentLOFC OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Counts the number of loss of frame events measured encountered in the current 15 minute interval." ::= { hwTdmE1CurrentStatEntry 9 } hwTdmE1CurrentCSSs OBJECT-TYPE SYNTAX Gauge32 (0..899) MAX-ACCESS read-only STATUS current DESCRIPTION "Counts the number of controlled slip seconds measured encountered in the current 15 minute interval." ::= { hwTdmE1CurrentStatEntry 10 } hwTdmE1CurrentDMs OBJECT-TYPE SYNTAX Gauge32 (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "Counts the number of degraded minutes measured encountered in the current 15 minute interval." ::= { hwTdmE1CurrentStatEntry 11 } hwTdmE1TimeElapsed OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of seconds that have elapsed since the beginning of the near end current error- measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value." ::= { hwTdmE1CurrentStatEntry 12 } -- -- ASMi52A E1 Port statistics in 15 minute interval Table -- hwTdmE1IntervalStatTable OBJECT-TYPE SYNTAX SEQUENCE OF HwTdmE1IntervalStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM Modem E1 port statistics in 15 minute interval. This information describe the E1 port interval index, the number of errored seconds, the number of unavailable seconds, the number of severely errored seconds, the number of bursty errored seconds, the number of loss of frame events, the number of controlled slip seconds and the number of degraded minutes.The indexes of this table are ifIndex, hwTdmE1IntervalIndex." ::= { hwTdmPortStatObjects 5 } hwTdmE1IntervalStatEntry OBJECT-TYPE SYNTAX HwTdmE1IntervalStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the reference information about a TDM Modem E1 port statistics in 15 minute interval. This information describe the E1 port interval index, the number of errored seconds, the number of unavailable seconds, the number of severely errored seconds, the number of bursty errored seconds, the number of loss of frame events, the number of controlled slip seconds and the number of degraded minutes.The indexes of this entry are ifIndex, hwTdmE1IntervalIndex." INDEX { ifIndex, hwTdmE1IntervalIndex } ::= { hwTdmE1IntervalStatTable 1 } HwTdmE1IntervalStatEntry ::= SEQUENCE { hwTdmE1IntervalIndex Integer32, hwTdmE1IntervalESs Gauge32, hwTdmE1IntervalUASs Gauge32, hwTdmE1IntervalSESs Gauge32, hwTdmE1IntervalBESs Gauge32, hwTdmE1IntervalLOFC Gauge32, hwTdmE1IntervalCSSs Gauge32, hwTdmE1IntervalDMs Gauge32, hwTdmE1TotalIntervalNum Integer32, hwTdmE1Interval1DayESs Gauge32, hwTdmE1Interval1DayUASs Gauge32, hwTdmE1Interval1DaySESs Gauge32, hwTdmE1Interval1DayBESs Gauge32, hwTdmE1Interval1DayLOFC Gauge32, hwTdmE1Interval1DayCSSs Gauge32, hwTdmE1Interval1DayDMs Gauge32, hwTdmE1Interval1DayDEGMinute Gauge32 } hwTdmE1IntervalIndex OBJECT-TYPE SYNTAX Integer32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This value indicates the interval E1 port statistics index in the remote modem." ::= { hwTdmE1IntervalStatEntry 1 } hwTdmE1IntervalESs OBJECT-TYPE SYNTAX Gauge32 (0..899) MAX-ACCESS read-only STATUS current DESCRIPTION "Counts the number of errored seconds measured encountered in 15 minute interval." ::= { hwTdmE1IntervalStatEntry 2 } hwTdmE1IntervalUASs OBJECT-TYPE SYNTAX Gauge32 (0..900) MAX-ACCESS read-only STATUS current DESCRIPTION "Counts the number of unavailable seconds measured encountered in 15 minute interval." ::= { hwTdmE1IntervalStatEntry 3 } hwTdmE1IntervalSESs OBJECT-TYPE SYNTAX Gauge32 (0..900) MAX-ACCESS read-only STATUS current DESCRIPTION "Counts the number of severely errored seconds measured encountered in 15 minute interval." ::= { hwTdmE1IntervalStatEntry 4 } hwTdmE1IntervalBESs OBJECT-TYPE SYNTAX Gauge32 (0..899) MAX-ACCESS read-only STATUS current DESCRIPTION "Counts the number of bursty errored seconds measured encountered in 15 minute interval." ::= { hwTdmE1IntervalStatEntry 5 } hwTdmE1IntervalLOFC OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Counts the number of loss of frame events measured encountered in 15 minute interval." ::= { hwTdmE1IntervalStatEntry 6 } hwTdmE1IntervalCSSs OBJECT-TYPE SYNTAX Gauge32 (0..899) MAX-ACCESS read-only STATUS current DESCRIPTION "Counts the number of controlled slip seconds measured encountered in 15 minute interval." ::= { hwTdmE1IntervalStatEntry 7 } hwTdmE1IntervalDMs OBJECT-TYPE SYNTAX Gauge32 (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "Counts the number of degraded minutes measured encountered in 15 minute interval." ::= { hwTdmE1IntervalStatEntry 8 } hwTdmE1TotalIntervalNum OBJECT-TYPE SYNTAX Integer32 (1..96) MAX-ACCESS read-only STATUS current DESCRIPTION "This value indicates the total number of E1 port statistics in 15 minute interval in 24 hour statistics." ::= { hwTdmE1IntervalStatEntry 9 } hwTdmE1Interval1DayESs OBJECT-TYPE SYNTAX Gauge32 (0..86304) MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of Errored Seconds encountered by a E1 interface in the previous 24 hour interval." ::= { hwTdmE1IntervalStatEntry 10 } hwTdmE1Interval1DayUASs OBJECT-TYPE SYNTAX Gauge32 (0..86400) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Unavailable Seconds encountered by a E1 interface in the previous 24 hour interval." ::= { hwTdmE1IntervalStatEntry 11 } hwTdmE1Interval1DaySESs OBJECT-TYPE SYNTAX Gauge32 (0..86400) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Severely Errored Seconds encountered by a E1 interface in the previous 24 hour interval. " ::= { hwTdmE1IntervalStatEntry 12 } hwTdmE1Interval1DayBESs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Bursty Errored Seconds (BESs) encountered by a E1 interface in the previous 24 hour interval." ::= { hwTdmE1IntervalStatEntry 13 } hwTdmE1Interval1DayLOFC OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of loss of frame events encountered by a E1 interface in the previous 24 hour interval." ::= { hwTdmE1IntervalStatEntry 14 } hwTdmE1Interval1DayCSSs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Controlled Slip Seconds encountered by a E1 interface in the previous 24 hour interval." ::= { hwTdmE1IntervalStatEntry 15 } hwTdmE1Interval1DayDMs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Degraded Minutes (DMs) encountered by a E1 interface in the previous 24 hour interval." ::= { hwTdmE1IntervalStatEntry 16 } hwTdmE1Interval1DayDEGMinute OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of DEG Minutes encountered by a E1 interface in the previous 24 hour interval." ::= { hwTdmE1IntervalStatEntry 17 } -- -- ASMi52A E1 Port statistics Table in 1 day interval -- -- hwTdmE1TotalStatTable OBJECT-TYPE -- SYNTAX SEQUENCE OF HwTdmE1TotalStatEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "The TDM Modem E1 port statistics Table in 1 day interval." -- ::= { hwTdmPortStatObjects 6 } -- hwTdmE1TotalStatEntry OBJECT-TYPE -- SYNTAX HwTdmE1TotalStatEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "An entry in the TDM Modem E1 port statistics table describes the reference -- information about a TDM Modem E1 port statistics in 24 hour interval. -- This information describe the E1 port total index, the total number of E1 -- port statistics in 15 minute interval, the number of errored seconds, the -- number of unavailable seconds, the number of severely errored seconds, the -- number of bursty errored seconds, the number of loss of frame events, the -- number of controlled slip seconds and the number of degraded minutes." -- INDEX { ifIndex, hwTdmE1TotalIndex } -- ::= { hwTdmE1TotalStatTable 1 } -- HwTdmE1TotalStatEntry ::= -- SEQUENCE { -- hwTdmE1TotalIndex -- INTEGER, -- hwTdmE1TotalIntervalNum -- INTEGER, -- hwTdmE1TotalESs -- Gauge32, -- hwTdmE1TotalUASs -- Gauge32, -- hwTdmE1TotalSESs -- Gauge32, -- hwTdmE1TotalBESs -- Gauge32, -- hwTdmE1TotalLOFC -- Gauge32, -- hwTdmE1TotalCSSs -- Gauge32, -- hwTdmE1TotalDMs -- Gauge32, -- hwTdmE1TotalDEGMinute -- Gauge32 -- } -- hwTdmE1TotalIndex OBJECT-TYPE -- SYNTAX INTEGER (0..6) -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "This value indicates the interval E1 port statistics index in the remote -- modem." -- ::= { hwTdmE1TotalStatEntry 1 } -- hwTdmE1TotalIntervalNum OBJECT-TYPE -- SYNTAX INTEGER (0..95) -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "This value indicates the total number of E1 port statistics in 15 minute -- interval in 24 hour statistics." -- ::= { hwTdmE1TotalStatEntry 2 } -- hwTdmE1TotalESs OBJECT-TYPE -- SYNTAX Gauge32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The sum of Errored Seconds encountered by a E1 interface in the previous -- 24 hour interval." -- ::= { hwTdmE1TotalStatEntry 3 } -- hwTdmE1TotalUASs OBJECT-TYPE -- SYNTAX Gauge32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The number of Unavailable Seconds encountered by a E1 interface in the -- previous 24 hour interval." -- ::= { hwTdmE1TotalStatEntry 4 } -- hwTdmE1TotalSESs OBJECT-TYPE -- SYNTAX Gauge32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The number of Severely Errored Seconds encountered by a E1 interface in -- the previous 24 hour interval. " -- ::= { hwTdmE1TotalStatEntry 5 } -- hwTdmE1TotalBESs OBJECT-TYPE -- SYNTAX Gauge32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The number of Bursty Errored Seconds (BESs) encountered by a E1 interface -- in the previous 24 hour interval." -- ::= { hwTdmE1TotalStatEntry 6 } -- hwTdmE1TotalLOFC OBJECT-TYPE -- SYNTAX Gauge32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The number of loss of frame events encountered by a E1 interface in the -- previous 24 hour interval." -- ::= { hwTdmE1TotalStatEntry 7 } -- hwTdmE1TotalCSSs OBJECT-TYPE -- SYNTAX Gauge32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The number of Controlled Slip Seconds encountered by a E1 interface in the -- previous 24 hour interval." -- ::= { hwTdmE1TotalStatEntry 8 } --hwTdmE1TotalDMs OBJECT-TYPE -- SYNTAX Gauge32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The number of Degraded Minutes (DMs) encountered by a E1 interface in the -- previous 24 hour interval." -- ::= { hwTdmE1TotalStatEntry 9 } -- hwTdmE1TotalDEGMinute OBJECT-TYPE -- SYNTAX Gauge32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The number of DEG Minutes encountered by a E1 interface in the -- previous 24 hour interval." -- ::= { hwTdmE1TotalStatEntry 10 } -- -- ADTRAN Script Configuration Table -- hwTdmAdtranScriptTable OBJECT-TYPE SYNTAX SEQUENCE OF HwTdmAdtranScriptEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the configuration about a TDM Modem to config TDM SHDSL terminal.The index of this table is ifIndex." ::= { hwTdmCommonConfiguration 1 } hwTdmAdtranScriptEntry OBJECT-TYPE SYNTAX HwTdmAdtranScriptEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the configuration about a TDM Modem to config TDM SHDSL terminal.The index of this entry is ifIndex." INDEX { ifIndex } ::= { hwTdmAdtranScriptTable 1 } HwTdmAdtranScriptEntry ::= SEQUENCE { hwTdmAdtranScript OCTET STRING, hwTdmAdtranScriptLatestResult INTEGER } -- hwTdmConfigurationScript hwTdmAdtranScript OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to config TDM SHDSL terminal, and it may include sereval commands. Each command ends with one or more '\n', and every '\n' means delay 1 second too. For example: command '123\r\n\n\n45\n' expects two steps. The first step is send '123\r' to the terminal, then delay 3 seconds, and the second step is send '45' to the terminal, then delay 1 second. " ::= { hwTdmAdtranScriptEntry 1 } hwTdmAdtranScriptLatestResult OBJECT-TYPE SYNTAX INTEGER { idle(1), fail(2), busy(3), success(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The result of the lastest script configuration. Options: 1. idle(1) - Indicates that no configuration. 2. fail(2) - Indicates that last configuration failed. 3. busy(3) - Indicates that Operating new config. 4. success(4) - Indicates that last configuration successed. " ::= { hwTdmAdtranScriptEntry 2 } -- -- Compliance statements -- hwTdmMIBTftpCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for TFTP download." MODULE -- this module MANDATORY-GROUPS { hwTdmMIBTftpGroup } ::= { hwTdmMIBCompliances 1 } -- Units of compliance hwTdmMIBTftpGroup OBJECT-GROUP OBJECTS { -- ifIndex, hwTdmTftpFileServerIP, hwTdmTftpFileName, hwTdmTftpFileTransCmd } STATUS current DESCRIPTION "A collection of objects providing for TFTP uploading and downloading." ::= { hwTdmMIBGroups 1 } END