-- ***************************************************************** -- FS-OSPF-MIB.mib: FS Ospf MIB file -- -- November 2002, ChenXingBin -- -- Copyright (c) 2002 by FS.COM Inc.. -- All rights reserved. -- -- ***************************************************************** -- FS-OSPF-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, TimeTicks, IpAddress, Unsigned32, Gauge32, Counter32 FROM SNMPv2-SMI TruthValue, RowStatus FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ConfigStatus FROM FS-TC EnabledStatus FROM P-BRIDGE-MIB AreaID, Status, PositiveInteger, DesignatedRouterPriority, RouterID, HelloRange FROM OSPF-MIB fsMgmt FROM FS-SMI; fsOspfMIB MODULE-IDENTITY LAST-UPDATED "200211200000Z" ORGANIZATION "FS.COM Inc.." CONTACT-INFO " Tel: 400-865-2852 E-mail: https://www.fs.com/live_chat_service_mail.html" DESCRIPTION "This module defines fs Ospf mibs." REVISION "200211200000Z" DESCRIPTION "Initial version of this MIB module." ::= { fsMgmt 30} fsOspfMIBObjects OBJECT IDENTIFIER ::= { fsOspfMIB 1 } -- general mib fsOspfGeneralMibsGroup OBJECT IDENTIFIER ::= { fsOspfMIBObjects 1 } --Minimum LSA interval fsOspfMiniLsaInterval OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum LSA interval that the two LSA generate." ::={ fsOspfGeneralMibsGroup 1 } --Minimum LSA arrival fsOspfMiniLsaArrival OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum LSA Interval of the two LSA arrival." ::={ fsOspfGeneralMibsGroup 2 } --Number of areas in this router fsOspfAreasNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of areas in this router" ::={ fsOspfGeneralMibsGroup 3 } fsOspfNormalAreasNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of normal areas in this router" ::={ fsOspfGeneralMibsGroup 4} fsOspfStubAreasNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of stub areas in this router" ::={ fsOspfGeneralMibsGroup 5 } fsOspfNssaAreasNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of nssa areas in this router" ::={ fsOspfGeneralMibsGroup 6 } fsOspfSpfDelay OBJECT-TYPE SYNTAX Unsigned32(0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "Ospf Spf shedule time, an integer from 0 to 65535. The default is 5 seconds,0 means no delay." DEFVAL {5} ::={ fsOspfGeneralMibsGroup 7 } fsOspfSpfHoldTime OBJECT-TYPE SYNTAX Unsigned32(0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "hold time between two Spfs.an integer from 0 to 65535. The default is 10 seconds; 0 means no delay." DEFVAL {10} ::={ fsOspfGeneralMibsGroup 8 } fsOspfAutoCostRefBandWidthRef OBJECT-TYPE SYNTAX Unsigned32(0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "Set AutoCost bandwidth referenc value in unit of Mbits. Setting this value to 0 indicate that disable the feature of autocost bandwidth referenc." DEFVAL {100} ::={ fsOspfGeneralMibsGroup 9 } fsOspfLsaGroupPacing OBJECT-TYPE SYNTAX Unsigned32(10..1800) MAX-ACCESS read-write STATUS current DESCRIPTION "set the group pacing of LSAs." DEFVAL {240} ::={ fsOspfGeneralMibsGroup 10} fsOspfInterDistance OBJECT-TYPE SYNTAX Unsigned32(1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Set inter-area distance." DEFVAL {110} ::= { fsOspfGeneralMibsGroup 11 } fsOspfIntraDistance OBJECT-TYPE SYNTAX Unsigned32(1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Set intra-area distance." DEFVAL {110} ::= { fsOspfGeneralMibsGroup 12 } fsOspfExternDistance OBJECT-TYPE SYNTAX Unsigned32(1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Set extern distance." DEFVAL {110} ::= { fsOspfGeneralMibsGroup 13 } --LogAdjChangeNotify fsOspfLogAdjChangeNotify OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "if enabled status is setted, Send syslog message when a neighbor state changes." DEFVAL {enabled} ::= { fsOspfGeneralMibsGroup 14 } fsOspfPassiveStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The fsOspfIfPassiveStatus of a interface equal to this object value when this interface is created. If you change this object value to 'enabled' or 'disabled'all interfaces which have exist will also change their fsOspfIfPassiveStatus to 'enabled' or 'disabled'." DEFVAL { disabled } ::={ fsOspfGeneralMibsGroup 15 } fsOspfRFC1583Compatibility OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Controls the preference rules used in calculating AS external routes (RFC2328 Section 16.4) when choosing among multiple AS-external-LSAs advertising the same destination. When set to 'enabled', the preference rules remain those specified by RFC 1583 ([Ref9]). When set to 'disabled', the preference rules are those stated in 'RFC2328 Section 16.4.1' which prevent routing loops when AS- external-LSAs for the same destination have been originated from different areas. Set to 'enabled' by default." REFERENCE "OSPF Version 2(RFC2328), C.1 Global parameters" DEFVAL { enabled } ::={ fsOspfGeneralMibsGroup 16 } fsOspfRouteRedisDefMetricVal OBJECT-TYPE SYNTAX Unsigned32(1..16777214) MAX-ACCESS read-write STATUS current DESCRIPTION "When this value is setted,Cause the current routing protocol(ospf) to use the same metricvalue for all redistributed routes (BGP, RIP, and OSPF)." DEFVAL {20} ::= { fsOspfGeneralMibsGroup 17} fsOspfAdminiDistance OBJECT-TYPE SYNTAX Unsigned32(1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "ospf Administrative distance." DEFVAL {110} ::= { fsOspfGeneralMibsGroup 18} --table mib --fsOspfAreaTable fsOspfAreaTable OBJECT-TYPE SYNTAX SEQUENCE OF FSOspfAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information describing the configured parame- ters and cumulative statistics of the router's attached areas.This table is superset of ospfAreaTable" ::= { fsOspfMIBObjects 2} fsOspfAreaEntry OBJECT-TYPE SYNTAX FSOspfAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of fsOspfAreaTable." INDEX { fsOspfAreaId} ::= { fsOspfAreaTable 1 } FSOspfAreaEntry ::= SEQUENCE { fsOspfAreaId AreaID, fsOspfAuthType INTEGER, fsOspfImportAsExtern INTEGER, fsOspfSpfRuns Counter32, fsOspfAreaBdrRtrCount Gauge32, fsOspfAsBdrRtrCount Gauge32, fsOspfAreaLsaCount Gauge32, fsOspfAreaLsaCksumSum Unsigned32, fsOspfAreaSummary INTEGER, fsOspfAreaStatus RowStatus, -- extend parts fsOspfAreaInterfaceNum Unsigned32, fsOspfAreaNssaIsRedistribution TruthValue, fsOspfAreaNssaIsDefInfoOriginate TruthValue } fsOspfAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { fsOspfAreaEntry 1 } fsOspfAuthType OBJECT-TYPE SYNTAX INTEGER{ none(0), simplePassword(1), md5 (2) -- reserved for specification by IANA (> 2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The authentication type specified for an area. Additional authentication types may be assigned locally on a per Area basis." REFERENCE "OSPF Version 2, Appendix E Authentication" DEFVAL { 0 } -- no authentication, by default ::= { fsOspfAreaEntry 2 } fsOspfImportAsExtern OBJECT-TYPE SYNTAX INTEGER { importExternal (1), --normal area importNoExternal (2), -- stub area importNssa (3) -- NSSA area } MAX-ACCESS read-create STATUS current DESCRIPTION "The area's support for importing AS external link- state advertisements." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" DEFVAL { importExternal } ::= { fsOspfAreaEntry 3 } fsOspfSpfRuns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times that the intra-area route table has been calculated using this area's link-state database. This is typically done using Dijkstra's algorithm." ::= { fsOspfAreaEntry 4 } fsOspfAreaBdrRtrCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of area border routers reach- able within this area. This is initially zero, and is calculated in each SPF Pass." ::= { fsOspfAreaEntry 5 } fsOspfAsBdrRtrCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass." ::= { fsOspfAreaEntry 6 } fsOspfAreaLsaCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of link-state advertisements in this area's link-state database, excluding AS External LSA's." ::= { fsOspfAreaEntry 7 } fsOspfAreaLsaCksumSum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The 32-bit unsigned sum of the link-state ad- vertisements' LS checksums contained in this area's link-state database. This sum excludes external (LS type 5) link-state advertisements. The sum can be used to determine if there has been a change in a router's link state data- base, and to compare the link-state database of two routers." DEFVAL { 0 } ::= { fsOspfAreaEntry 8 } fsOspfAreaSummary OBJECT-TYPE SYNTAX INTEGER { noAreaSummary (1), sendAreaSummary (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The variable ospfAreaSummary controls the im- port of summary LSAs into stub areas. It has no effect on other areas. If it is noAreaSummary, the router will neither originate nor propagate summary LSAs into the stub area. It will rely entirely on its de- fault route. If it is sendAreaSummary, the router will both summarize and propagate summary LSAs." DEFVAL { sendAreaSummary } ::= { fsOspfAreaEntry 9 } fsOspfAreaStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { fsOspfAreaEntry 10 } fsOspfAreaInterfaceNum OBJECT-TYPE --for command "show SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " the interface number of this area" ::= { fsOspfAreaEntry 11 } fsOspfAreaNssaIsRedistribution OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION " if it's disabled , when the router is an NSSA ABR and you want the redistribute command to import routes into normal areas, but not into the NSSA, this field is vaild for nssa area" DEFVAL {true} ::= { fsOspfAreaEntry 12} fsOspfAreaNssaIsDefInfoOriginate OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "if it's enabled it meaning that on an ABR to allow importing type 7 LSAs into the NSSA, this field is valid for nssa area" DEFVAL {false} ::= { fsOspfAreaEntry 13} --network address scope table fsOspfAddressScopeTable OBJECT-TYPE SYNTAX SEQUENCE OF FSOspfAddressScopeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Define an interface on which OSPF runs and the area ID for that interface. You can use the wildcard-mask to use a single command to define one or more multiple interfaces to be associated with a specific OSPF area. " ::= { fsOspfMIBObjects 3 } fsOspfAddressScopeEntry OBJECT-TYPE SYNTAX FSOspfAddressScopeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry define an scope of address for ospf routing." INDEX { fsOspfNetWorkAreaID,fsOspfNetWorkAddress, fsOspfNetWorkMask} ::= { fsOspfAddressScopeTable 1 } FSOspfAddressScopeEntry ::= SEQUENCE { fsOspfNetWorkAreaID IpAddress, fsOspfNetWorkAddress IpAddress, fsOspfNetWorkMask IpAddress, fsOspfNetWorkStatus RowStatus } fsOspfNetWorkAreaID OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "area ID" ::= { fsOspfAddressScopeEntry 1 } fsOspfNetWorkAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " Routing for Networks Ipaddress" ::= { fsOspfAddressScopeEntry 2 } fsOspfNetWorkMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " Routing for Networks mask" ::= { fsOspfAddressScopeEntry 3 } fsOspfNetWorkStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION " when this value is destroy,the entry will be deleted" ::= { fsOspfAddressScopeEntry 4 } -- The Ospf Interface Configuration Table fsOspfIfTable OBJECT-TYPE SYNTAX SEQUENCE OF FSOspfIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Interface Table describes the interfaces from the viewpoint of OSPF." REFERENCE "ospfIfTable in rfc1850" ::= { fsOspfMIBObjects 4 } fsOspfIfEntry OBJECT-TYPE SYNTAX FSOspfIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Interface Entry describes one inter- face configuration of OSPF." INDEX { fsOspfIfIpAddress, fsOspfAddressLessIf } ::= { fsOspfIfTable 1 } FSOspfIfEntry ::= SEQUENCE { fsOspfIfIpAddress IpAddress, fsOspfAddressLessIf Unsigned32, fsOspfIfAreaId AreaID, fsOspfIfType INTEGER, fsOspfIfAdminStat Status, fsOspfIfRtrPriority DesignatedRouterPriority, fsOspfIfTransitDelay Unsigned32, fsOspfIfRetransInterval Unsigned32, fsOspfIfHelloInterval HelloRange, fsOspfIfRtrDeadInterval PositiveInteger, fsOspfIfPollInterval PositiveInteger, fsOspfIfState INTEGER, fsOspfIfDesignatedRouter IpAddress, fsOspfIfBackupDesignatedRouter IpAddress, fsOspfIfEvents Counter32, fsOspfIfAuthType INTEGER, fsOspfIfAuthKey OCTET STRING, fsOspfIfStatus RowStatus, fsOspfIfMulticastForwarding INTEGER, fsOspfIfDemand TruthValue, fsOspfIfDatabaseFilterAllOut EnabledStatus, fsOspfIfDesignateRouterId IpAddress, fsOspfIfBackupDesignateRouterId IpAddress, fsOspfIfWaitInternal TimeTicks, fsOspfIfPassiveStatus EnabledStatus, fsOspfIfCurrentUsedMd5AuthKeyId Unsigned32 } fsOspfIfIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of this OSPF interface." ::= { fsOspfIfEntry 1 } fsOspfAddressLessIf OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address." ::= { fsOspfIfEntry 2 } fsOspfIfAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone." DEFVAL { '00000000'H } -- 0.0.0.0 ::= { fsOspfIfEntry 3 } fsOspfIfType OBJECT-TYPE SYNTAX INTEGER { broadcast (1), nbma (2), pointToPoint (3), pointToMultipoint (5), loopback(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broad- cast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast', X.25 and similar technologies take the value 'nbma', and links that are definitively point to point take the value 'pointToPoint'." ::= { fsOspfIfEntry 4 } fsOspfIfAdminStat OBJECT-TYPE SYNTAX Status MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF interface's administrative status. The value formed on the interface, and the in- terface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF." ::= { fsOspfIfEntry 5 } fsOspfIfRtrPriority OBJECT-TYPE SYNTAX DesignatedRouterPriority MAX-ACCESS read-write STATUS current DESCRIPTION "The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligi- ble to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker." DEFVAL { 1 } ::= { fsOspfIfEntry 6 } fsOspfIfTransitDelay OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The estimated number of seconds it takes to transmit a link state update packet over this interface." DEFVAL { 1 } ::= { fsOspfIfEntry 7 } fsOspfIfRetransInterval OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets." DEFVAL { 5 } ::= { fsOspfIfEntry 8 } fsOspfIfHelloInterval OBJECT-TYPE SYNTAX HelloRange MAX-ACCESS read-write STATUS current DESCRIPTION "The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for all routers attached to a common network." DEFVAL { 10 } ::= { fsOspfIfEntry 9 } fsOspfIfRtrDeadInterval OBJECT-TYPE SYNTAX PositiveInteger MAX-ACCESS read-write STATUS current DESCRIPTION "The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network." DEFVAL { 40 } ::= { fsOspfIfEntry 10 } fsOspfIfPollInterval OBJECT-TYPE SYNTAX PositiveInteger MAX-ACCESS read-only STATUS current DESCRIPTION "The larger time interval, in seconds, between the Hello packets sent to an inactive non- broadcast multi- access neighbor." ::= { fsOspfIfEntry 11 } fsOspfIfState OBJECT-TYPE SYNTAX INTEGER { down (1), loopback (2), waiting (3), pointToPoint (4), designatedRouter (5), backupDesignatedRouter (6), otherDesignatedRouter (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Interface State." DEFVAL { down } ::= { fsOspfIfEntry 12 } fsOspfIfDesignatedRouter OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the interface which connected the local router in the Designated Router." DEFVAL { '00000000'H } -- 0.0.0.0 ::= { fsOspfIfEntry 13 } fsOspfIfBackupDesignatedRouter OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the interface which connected the local router in the Backup Designated Router." DEFVAL { '00000000'H } -- 0.0.0.0 ::= { fsOspfIfEntry 14 } fsOspfIfEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this OSPF interface has changed its state, or an error has occurred." ::= { fsOspfIfEntry 15 } fsOspfIfAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-write STATUS current DESCRIPTION "The Authentication Key. If the Area's Author- ization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, fsOspfIfAuthKey always returns an Oc- tet String of length zero." REFERENCE "OSPF Version 2, Section 9 The Interface Data Structure" DEFVAL { '0000000000000000'H } -- 0.0.0.0.0.0.0.0 ::= { fsOspfIfEntry 16 } fsOspfIfStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-only STATUS current DESCRIPTION "This value will be active(1) always." ::= { fsOspfIfEntry 17 } fsOspfIfMulticastForwarding OBJECT-TYPE SYNTAX INTEGER { blocked (1), -- no multicast forwarding multicast (2), -- using multicast address unicast (3) -- to each OSPF neighbor } MAX-ACCESS read-only STATUS current DESCRIPTION "The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link uni- casts. Data link multicasting is not meaning- ful on point to point and NBMA interfaces, and setting ospfMulticastForwarding to 0 effective- ly disables all multicast forwarding." DEFVAL { blocked } ::= { fsOspfIfEntry 18 } fsOspfIfDemand OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether Demand OSPF procedures (hel- lo supression to FULL neighbors and setting the DoNotAge flag on proogated LSAs) should be per- formed on this interface." DEFVAL { false } ::= { fsOspfIfEntry 19 } fsOspfIfAuthType OBJECT-TYPE SYNTAX INTEGER (0..255) -- none (0), -- simplePassword (1) -- md5 (2) -- default (3) -- reserved for specification by IANA (> 2) MAX-ACCESS read-write STATUS current DESCRIPTION "The authentication type specified for an interface. Setting this value to 'default' means using default authentication type referenced to Area Authentication, this value only for set,not be read. Additional authentication types may be assigned locally." REFERENCE "OSPF Version 2, Appendix E Authentication" DEFVAL { 0 } -- no authentication, by default ::= { fsOspfIfEntry 20 } fsOspfIfDatabaseFilterAllOut OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Block flooding of OSPF LSA packets to the interface. By default, OSPF floods new LSAs over all interfaces in the same area, except the interface on which the LSA arrives." DEFVAL {disabled} ::= { fsOspfIfEntry 21 } fsOspfIfDesignateRouterId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "DR RouterID of this interface, when DR does not selected,DR Id is 0.0.0.0" DEFVAL {'00000000'H} ::= { fsOspfIfEntry 22 } fsOspfIfBackupDesignateRouterId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Backup DR RouterId of this interface , when Backup DR does not selected,BDR Id is 0.0.0.0" DEFVAL {'00000000'H} ::= { fsOspfIfEntry 23 } fsOspfIfWaitInternal OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The wait time of hello generate" ::= { fsOspfIfEntry 24 } fsOspfIfPassiveStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object value to 'enabled' ,the interface will become a passive interface." DEFVAL { disabled } ::= { fsOspfIfEntry 25 } fsOspfIfCurrentUsedMd5AuthKeyId OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "key-id which current used for md5 authentication,this value is valid from 1 to 255, the value 0 is default value.." DEFVAL {0} ::= { fsOspfIfEntry 26 } -- The Ospf Interface MD5 authentication key configuration table fsOspfIfMd5AuthKeyTable OBJECT-TYPE SYNTAX SEQUENCE OF FSOspfIfMd5AuthKeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration table of the key-id for md5 authentication for OSPF protocol." ::= { fsOspfMIBObjects 5 } fsOspfIfMd5AuthKeyEntry OBJECT-TYPE SYNTAX FSOspfIfMd5AuthKeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration entry of the key-id for md5 authentication for OSPF protocol" INDEX {fsOspfIfMd5AuthKeyIf, fsOspfIfMd5AuthKeyId } ::= { fsOspfIfMd5AuthKeyTable 1 } FSOspfIfMd5AuthKeyEntry ::= SEQUENCE { fsOspfIfMd5AuthKeyIf Unsigned32, fsOspfIfMd5AuthKeyId Unsigned32, fsOspfIfMd5AuthKey OCTET STRING, fsOspfIfMd5AuthKeySt ConfigStatus } fsOspfIfMd5AuthKeyIf OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Corresponding value of ifIndex for interfaces." ::= { fsOspfIfMd5AuthKeyEntry 1 } fsOspfIfMd5AuthKeyId OBJECT-TYPE SYNTAX Unsigned32 (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "the key-id for md5 authentication." ::= { fsOspfIfMd5AuthKeyEntry 2 } fsOspfIfMd5AuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-create STATUS current DESCRIPTION "The Authentication Key for MD5. When read, fsOspfIfMd5AuthKey always returns an Oc- tet String of length zero." REFERENCE "OSPF Version 2, Section 9 The Interface Data Structure" ::= { fsOspfIfMd5AuthKeyEntry 3 } fsOspfIfMd5AuthKeySt OBJECT-TYPE SYNTAX ConfigStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this value to 'invalid' will delete this entry. Setting this value to 'valid' will have no effect." ::= { fsOspfIfMd5AuthKeyEntry 4 } -- The FS Ospf Virtual Link Table fsOspfVirtTable OBJECT-TYPE SYNTAX SEQUENCE OF FSOspfVirtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about this router's virtual inter- faces.Include ospfVirtIfTable in rfc1850" REFERENCE "ospfVirtIfTable in rfc1850" ::= { fsOspfMIBObjects 6 } fsOspfVirtEntry OBJECT-TYPE SYNTAX FSOspfVirtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a single Virtual Interface" INDEX {fsOspfVirtIfAreaId, fsOspfVirtIfNeighbor} ::= { fsOspfVirtTable 1 } FSOspfVirtEntry ::= SEQUENCE { fsOspfVirtIfAreaId AreaID, fsOspfVirtIfNeighbor RouterID, fsOspfVirtIfTransitDelay Unsigned32, fsOspfVirtIfRetransInterval Unsigned32, fsOspfVirtIfHelloInterval HelloRange, fsOspfVirtIfRtrDeadInterval PositiveInteger, fsOspfVirtIfState INTEGER, fsOspfVirtIfEvents Counter32, fsOspfVirtIfAuthType INTEGER, fsOspfVirtIfAuthKey OCTET STRING, fsOspfVirtIfStatus RowStatus, fsOspfVirtCost Unsigned32, fsOspfVirtNativeIfIndex INTEGER, fsOspfVirtLinkState INTEGER, fsOspfVirtHelloDueIn TimeTicks, fsOspfVirtCurrentUsedMd5AuthKeyId Unsigned32 } fsOspfVirtIfAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0" ::= { fsOspfVirtEntry 1 } fsOspfVirtIfNeighbor OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The Router ID of the Virtual Neighbor." ::= { fsOspfVirtEntry 2 } fsOspfVirtIfTransitDelay OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The estimated number of seconds it takes to transmit a link- state update packet over this interface." DEFVAL { 1 } ::= { fsOspfVirtEntry 3 } fsOspfVirtIfRetransInterval OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets. This value should be well over the expected round- trip time." DEFVAL { 5 } ::= { fsOspfVirtEntry 4 } fsOspfVirtIfHelloInterval OBJECT-TYPE SYNTAX HelloRange MAX-ACCESS read-create STATUS current DESCRIPTION "The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for the virtual neighbor." DEFVAL { 10 } ::= { fsOspfVirtEntry 5 } fsOspfVirtIfRtrDeadInterval OBJECT-TYPE SYNTAX PositiveInteger MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neigh- bor." DEFVAL { 40 } ::= { fsOspfVirtEntry 6 } fsOspfVirtIfState OBJECT-TYPE SYNTAX INTEGER { down (1), -- these use the same encoding pointToPoint (4) -- as the ospfIfTable } MAX-ACCESS read-only STATUS current DESCRIPTION "OSPF virtual interface states." DEFVAL { down } ::= { fsOspfVirtEntry 7 } fsOspfVirtIfEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of state changes or error events on this Virtual Link" ::= { fsOspfVirtEntry 8 } fsOspfVirtIfAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..256)) MAX-ACCESS read-create STATUS current DESCRIPTION "If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 oc- tets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, ospfVifAuthKey always returns a string of length zero." REFERENCE "OSPF Version 2, Section 9 The Interface Data Structure" DEFVAL { '0000000000000000'H } -- 0.0.0.0.0.0.0.0 ::= { fsOspfVirtEntry 9 } fsOspfVirtIfStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { fsOspfVirtEntry 10 } fsOspfVirtIfAuthType OBJECT-TYPE SYNTAX INTEGER (0..255) -- none (0), -- simplePassword (1), -- md5 (2), -- default (3) -- reserved for specification by IANA (> 2) MAX-ACCESS read-create STATUS current DESCRIPTION "The authentication type specified for a virtual interface. Setting this value 'default' means using default authentication type referenced to Area Authentication, this value only for set,not be read. Additional authentication types may be assigned locally." REFERENCE "OSPF Version 2, Appendix E Authentication" DEFVAL { 0 } -- no authentication, by default ::= { fsOspfVirtEntry 11 } fsOspfVirtCost OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Explicitly specify the cost of sending a packet on the interface." ::= { fsOspfVirtEntry 12 } fsOspfVirtNativeIfIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION " the Interface's Index that The Virtual Link via this interface." ::= { fsOspfVirtEntry 13 } fsOspfVirtLinkState OBJECT-TYPE SYNTAX INTEGER{ up(1), down(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Virtual Link State is up or down." ::= { fsOspfVirtEntry 14 } fsOspfVirtHelloDueIn OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION " the time when hello due in." ::= { fsOspfVirtEntry 15 } fsOspfVirtCurrentUsedMd5AuthKeyId OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "the key-id which current used for md5 authentication,this value is valid from 1 to 255, the value 0 is default value." DEFVAL {0} ::= { fsOspfVirtEntry 16 } -- The Ospf Virtual Interface MD5 authentication key configuration table fsOspfVirtIfMd5AuthKeyTable OBJECT-TYPE SYNTAX SEQUENCE OF FSOspfVirtIfMd5AuthKeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration table of the key-id for md5 authentication in VirtIf for OSPF protocol." ::= { fsOspfMIBObjects 7 } fsOspfVirtIfMd5AuthKeyEntry OBJECT-TYPE SYNTAX FSOspfVirtIfMd5AuthKeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration entry of the key-id for md5 authentication in VirtIf for OSPF protocol" INDEX {fsOspfVirtIfMd5AuthKeyAreaId, fsOspfVirtIfMd5AuthKeyNeighbor, fsOspfVirtIfMd5AuthKeyId } ::= { fsOspfVirtIfMd5AuthKeyTable 1 } FSOspfVirtIfMd5AuthKeyEntry ::= SEQUENCE { fsOspfVirtIfMd5AuthKeyAreaId AreaID, fsOspfVirtIfMd5AuthKeyNeighbor RouterID, fsOspfVirtIfMd5AuthKeyId Unsigned32, fsOspfVirtIfMd5AuthKey OCTET STRING, fsOspfVirtIfMd5AuthKeySt ConfigStatus } fsOspfVirtIfMd5AuthKeyAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0" ::= { fsOspfVirtIfMd5AuthKeyEntry 1 } fsOspfVirtIfMd5AuthKeyNeighbor OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The Router ID of the Virtual Neighbor." ::= { fsOspfVirtIfMd5AuthKeyEntry 2 } fsOspfVirtIfMd5AuthKeyId OBJECT-TYPE SYNTAX Unsigned32 (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "the key-id for md5 authentication." ::= { fsOspfVirtIfMd5AuthKeyEntry 3 } fsOspfVirtIfMd5AuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-create STATUS current DESCRIPTION "The Authentication Key for MD5. When read, fsOspfVirtIfMd5AuthKey always returns an Oc- tet String of length zero." REFERENCE "OSPF Version 2, Section 9 The Interface Data Structure" ::= { fsOspfVirtIfMd5AuthKeyEntry 4 } fsOspfVirtIfMd5AuthKeySt OBJECT-TYPE SYNTAX ConfigStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this value to 'invalid' will delete this entry. Setting this value to 'valid' will have no effect." ::= { fsOspfVirtIfMd5AuthKeyEntry 5 } fsOspfLsaDetailInfoMibsGroup OBJECT IDENTIFIER ::= { fsOspfMIBObjects 8 } -- OSPF Link State Database -- The Link State Database contains the Link State -- Advertisements from throughout the areas that the -- device is attached to. fsOspfLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF FSOspfLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Process's Link State Database." REFERENCE "OSPF Version 2, Section 12 Link State Adver- tisements" ::= { fsOspfLsaDetailInfoMibsGroup 1 } fsOspfLsdbEntry OBJECT-TYPE SYNTAX FSOspfLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A single Link State Advertisement." INDEX { fsOspfLsdbAreaId, fsOspfLsdbType, fsOspfLsdbLsid, fsOspfLsdbRouterId } ::= { fsOspfLsdbTable 1 } FSOspfLsdbEntry ::= SEQUENCE { fsOspfLsdbAreaId AreaID, fsOspfLsdbType INTEGER, fsOspfLsdbLsid IpAddress, fsOspfLsdbRouterId RouterID, fsOspfLsdbSequence Unsigned32, fsOspfLsdbAge Unsigned32, fsOspfLsdbChecksum Unsigned32, fsOspfLsdbAdvertisement OCTET STRING, fsOspfLsdbLinkNum --equal LinkCount Unsigned32, fsOspfLsdbPacketLength Unsigned32, fsOspfSummaryLsaNetworkMask IpAddress, fsOspfSummaryLsaTos0Metric Unsigned32, fsOspfNssaLsaDetailMetricType INTEGER, fsOspfNssaLsaDetailForwardAddr IpAddress, fsOspfNssaLsaDetailRouteTag Unsigned32, fsOspfLsdbOption Unsigned32 } fsOspfLsdbAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "The 32 bit identifier of the Area from which the LSA was received." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { fsOspfLsdbEntry 1 } -- External Link State Advertisements are permitted -- for backward compatibility, but should be displayed in -- the ospfExtLsdbTable rather than here. fsOspfLsdbType OBJECT-TYPE SYNTAX INTEGER { routerLink (1), networkLink (2), summaryLink (3), asSummaryLink (4), asExternalLink (5), -- but see fsOspfExtLsdbTable multicastLink (6), nssaExternalLink (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertise- ment format." REFERENCE "OSPF Version 2, Appendix A.4.1 The Link State Advertisement header" ::= { fsOspfLsdbEntry 2 } fsOspfLsdbLsid OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement." REFERENCE "OSPF Version 2, Section 12.1.4 Link State ID" ::= { fsOspfLsdbEntry 3 } fsOspfLsdbRouterId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The 32 bit number that uniquely identifies the originating router in the Autonomous System." REFERENCE "OSPF Version 2, Appendix C.1 Global parameters" ::= { fsOspfLsdbEntry 4 } -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It fss with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. fsOspfLsdbSequence OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement." REFERENCE "OSPF Version 2, Section 12.1.6 LS sequence number" ::= { fsOspfLsdbEntry 5 } fsOspfLsdbAge OBJECT-TYPE SYNTAX Unsigned32 -- Should be 0..MaxAge MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the age of the link state adver- tisement in seconds." REFERENCE "OSPF Version 2, Section 12.1.1 LS age" ::= { fsOspfLsdbEntry 6 } fsOspfLsdbChecksum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum." REFERENCE "OSPF Version 2, Section 12.1.7 LS checksum" ::= { fsOspfLsdbEntry 7 } fsOspfLsdbAdvertisement OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "The entire Link State Advertisement, including its header." REFERENCE "OSPF Version 2, Section 12 Link State Adver- tisements" ::= { fsOspfLsdbEntry 8 } fsOspfLsdbLinkNum OBJECT-TYPE SYNTAX Unsigned32(0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION " the link count of this Router Link Lsa , this field is only valid for Router Link LsaŁ¨type 1 LSA)" ::= { fsOspfLsdbEntry 9 } fsOspfLsdbPacketLength OBJECT-TYPE SYNTAX Unsigned32(0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "the lsa packet length ." ::= { fsOspfLsdbEntry 10 } fsOspfSummaryLsaNetworkMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "this field is only useful when ospfLsdbType is type-3 or type-4 or type-7,it's the Lsa's network mask ." ::= { fsOspfLsdbEntry 11 } fsOspfSummaryLsaTos0Metric OBJECT-TYPE SYNTAX Unsigned32(0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "this field is only useful when ospfLsdbType is type-3 or type-4 or type-7,it's the Lsa's tos0 metric ." ::= { fsOspfLsdbEntry 12 } fsOspfNssaLsaDetailMetricType OBJECT-TYPE SYNTAX INTEGER { type1(1), type2(2) } MAX-ACCESS read-only STATUS current DESCRIPTION " this field is valid when Lsa is a type-7 LSA. The type of Nssa ernal metric. If bit E is set, the metric specified is a Type 2 external metric. This means the metric is considered larger than any link state path. If bit E is zero, the specified metric is a Type 1 external metric. This means that it is expressed in the same units as the link state metric (i.e., the same units as interface cost). " ::= { fsOspfLsdbEntry 13 } fsOspfNssaLsaDetailForwardAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "this field is valid when Lsa is a type-7 LSA. Data traffic for the advertised destination will be forwarded to this address. If the Forwarding address is set to 0.0.0.0, data traffic will be forwarded instead to the LSA's originator (i.e., the responsible AS boundary router) ." ::= { fsOspfLsdbEntry 14 } fsOspfNssaLsaDetailRouteTag OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " this field is valid when Lsa is a type-7 LSA. A 32-bit field attached to each external route. This is not used by the OSPF protocol itself. It may be used to communicate information between AS boundary routers; the precise nature of such information is outside the scope of this specification." ::= { fsOspfLsdbEntry 15 } fsOspfLsdbOption OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "the option field indicate which optional capabilities area associated with the LSA. " REFERENCE "OSPF Version 2, Appendix A.2, the Options Field" ::= { fsOspfLsdbEntry 16 } -- OSPF Link State Database, External -- The Link State Database contains the Link State -- Advertisements from throughout the areas that the -- device is attached to. -- This table is identical to the OSPF LSDB Table in -- format, but contains only External Link State -- Advertisements. The purpose is to allow external -- LSAs to be displayed once for the router rather -- than once in each non-stub area. fsOspfExtLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF FSOspfExtLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Process's Links State Database." REFERENCE "OSPF Version 2, Section 12 Link State Adver- tisements" ::= { fsOspfLsaDetailInfoMibsGroup 2 } fsOspfExtLsdbEntry OBJECT-TYPE SYNTAX FSOspfExtLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A single Link State Advertisement." INDEX { fsOspfExtLsdbType, fsOspfExtLsdbLsid, fsOspfExtLsdbRouterId } ::= { fsOspfExtLsdbTable 1 } FSOspfExtLsdbEntry ::= SEQUENCE{ fsOspfExtLsdbType INTEGER, fsOspfExtLsdbLsid IpAddress, fsOspfExtLsdbRouterId RouterID, fsOspfExtLsdbSequence Unsigned32, fsOspfExtLsdbAge Unsigned32, fsOspfExtLsdbChecksum Unsigned32, fsOspfExtLsdbAdvertisement OCTET STRING, fsOspfExtLsdbNetworkMask IpAddress, fsOspfExtLsdbMetricType INTEGER, fsOspfExtLsdbForwardAddr IpAddress, fsOspfExtLsdbRouteTag Unsigned32, fsOspfExtLsdbMetric INTEGER, fsOspfExtLsdbOption Unsigned32, fsOspfExtLsdbPacketLength Unsigned32 } fsOspfExtLsdbType OBJECT-TYPE SYNTAX INTEGER { asExternalLink (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertise- ment format." REFERENCE "OSPF Version 2, Appendix A.4.1 The Link State Advertisement header" ::= { fsOspfExtLsdbEntry 1 } fsOspfExtLsdbLsid OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement." REFERENCE "OSPF Version 2, Section 12.1.4 Link State ID" ::= { fsOspfExtLsdbEntry 2 } fsOspfExtLsdbRouterId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The 32 bit number that uniquely identifies the originating router in the Autonomous System." REFERENCE "OSPF Version 2, Appendix C.1 Global parameters" ::= { fsOspfExtLsdbEntry 3 } -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It fss with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. fsOspfExtLsdbSequence OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement." REFERENCE "OSPF Version 2, Section 12.1.6 LS sequence number" ::= { fsOspfExtLsdbEntry 4 } fsOspfExtLsdbAge OBJECT-TYPE SYNTAX Unsigned32 -- Should be 0..MaxAge MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the age of the link state adver- tisement in seconds." REFERENCE "OSPF Version 2, Section 12.1.1 LS age" ::= { fsOspfExtLsdbEntry 5 } fsOspfExtLsdbChecksum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum." REFERENCE "OSPF Version 2, Section 12.1.7 LS checksum" ::= { fsOspfExtLsdbEntry 6 } fsOspfExtLsdbAdvertisement OBJECT-TYPE SYNTAX OCTET STRING (SIZE(36)) MAX-ACCESS read-only STATUS current DESCRIPTION "The entire Link State Advertisement, including its header." REFERENCE "OSPF Version 2, Section 12 Link State Adver- tisements" ::= { fsOspfExtLsdbEntry 7 } fsOspfExtLsdbNetworkMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address mask for the advertised destination. For example, when advertising a class A network the mask 0xff000000 would be used." ::= { fsOspfExtLsdbEntry 8 } fsOspfExtLsdbMetric OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION " The cost of this route. Interpretation depends on the external type indication. " ::= { fsOspfExtLsdbEntry 9 } fsOspfExtLsdbMetricType OBJECT-TYPE SYNTAX INTEGER { type1(1), type2(2) } MAX-ACCESS read-only STATUS current DESCRIPTION " The type of external metric. If bit E is set, the metric specified is a Type 2 external metric. This means the metric is considered larger than any link state path. If bit E is zero, the specified metric is a Type 1 external metric. This means that it is expressed in the same units as the link state metric (i.e., the same units as interface cost). " ::= { fsOspfExtLsdbEntry 10 } fsOspfExtLsdbForwardAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " Data traffic for the advertised destination will be forwarded to this address. If the Forwarding address is set to 0.0.0.0, data traffic will be forwarded instead to the LSA's originator (i.e., the responsible AS boundary router) ." ::= { fsOspfExtLsdbEntry 11 } fsOspfExtLsdbRouteTag OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "A 32-bit field attached to each external route. This is not used by the OSPF protocol itself. It may be used to communicate information between AS boundary routers; the precise nature of such information is outside the scope of this specification." ::= { fsOspfExtLsdbEntry 12 } fsOspfExtLsdbOption OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "the option field indicate which optional capabilities area associated with the LSA. " REFERENCE "OSPF Version 2, Appendix A.2, the Options Field" ::= { fsOspfExtLsdbEntry 13 } fsOspfExtLsdbPacketLength OBJECT-TYPE SYNTAX Unsigned32(0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "the lsa packet length ." ::= { fsOspfExtLsdbEntry 14 } --Router Lsa's detail information table fsOspfRouterLsaDetailTable OBJECT-TYPE SYNTAX SEQUENCE OF FSOspfRouterLsaDetailEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the router Lsa's detail Infromtion." ::= { fsOspfLsaDetailInfoMibsGroup 3 } fsOspfRouterLsaDetailEntry OBJECT-TYPE SYNTAX FSOspfRouterLsaDetailEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry of this table." INDEX {fsOspfLsdbAreaId, fsOspfLsdbType, fsOspfLsdbLsid, fsOspfLsdbRouterId, fsOspfRouterLsaDetailLinkID } ::= { fsOspfRouterLsaDetailTable 1 } FSOspfRouterLsaDetailEntry ::= SEQUENCE{ fsOspfRouterLsaDetailLinkID IpAddress, fsOspfRouterLsaDetailLinkType INTEGER, fsOspfRouterLsaDetailLinkData IpAddress, fsOspfRouterLsaDetailTos0Metric Unsigned32 } fsOspfRouterLsaDetailLinkID OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "router lsa's link ID Identifies the object that this router link connects to. Value depends on the link's Type. When connecting to an object that also originates an LSA (i.e., another router or a transit network) the Link ID is equal to the neighboring LSA's Link State ID. This provides the key for looking up the neighboring LSA in the link state database during the routing table calculation. See Section 12.2 for more details. Type Link ID ________________________________________ 1 Neighboring router's Router ID 2 IP address of Designated Router 3 IP network/subnet number 4 Neighboring router's Router ID " ::= { fsOspfRouterLsaDetailEntry 1 } fsOspfRouterLsaDetailLinkType OBJECT-TYPE SYNTAX INTEGER{ pointtopointConnectionToAnotherRouter(1), connectionToaTransitNetwork(2), connectionToaStubNetwork(3), virtualLink(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "router lsa's link type A quick description of the router link. One of the following. Note that host routes are classified as links to stub networks with network mask of 0xffffffff." ::= { fsOspfRouterLsaDetailEntry 2 } fsOspfRouterLsaDetailLinkData OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " Value again depends on the link's Type field. For connections to stub networks, Link Data specifies the network's IP address mask. For unnumbered point-to-point connections, it specifies the interface's MIB-II ifIndex value. For the other link types it specifies the router interface's IP address. This latter piece of information is needed during the routing table build process, when calculating the IP address of the next hop. " ::= { fsOspfRouterLsaDetailEntry 3 } fsOspfRouterLsaDetailTos0Metric OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "TOS0-specific metric information." ::= { fsOspfRouterLsaDetailEntry 4 } --NetWork Lsa's detail information table fsOspfNetWorkLsaDetailTable OBJECT-TYPE SYNTAX SEQUENCE OF FSOspfNetWorkLsaDetailEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the NetWork Lsa's detail Infromtion." ::= { fsOspfLsaDetailInfoMibsGroup 4 } fsOspfNetWorkLsaDetailEntry OBJECT-TYPE SYNTAX FSOspfNetWorkLsaDetailEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry of this table." INDEX {fsOspfLsdbAreaId, fsOspfLsdbType, fsOspfLsdbLsid, fsOspfLsdbRouterId, fsOspfNetWorkLsaDetailAttachedRouter } ::= { fsOspfNetWorkLsaDetailTable 1 } FSOspfNetWorkLsaDetailEntry ::= SEQUENCE{ fsOspfNetWorkLsaDetailAttachedRouter IpAddress, fsOspfNetWorkLsaDetailNetworkMask IpAddress } fsOspfNetWorkLsaDetailAttachedRouter OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " The Router IDs of each of the routers attached to the network. Actually, only those routers that are fully adjacent to the Designated Router are listed. The Designated Router includes itself in this list. The number of routers included can be deduced from the LSA header's length field. " ::= { fsOspfNetWorkLsaDetailEntry 1 } fsOspfNetWorkLsaDetailNetworkMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address mask for the network. For example, a class A network would have the mask 0xff000000." ::= { fsOspfNetWorkLsaDetailEntry 2 } --fs Ospf Area Lsa Database Summary Table fsOspfAreaLsaDBSumTable OBJECT-TYPE SYNTAX SEQUENCE OF FSOspfAreaLsaDBSumEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Area LSA database summary Infromtion." ::= { fsOspfLsaDetailInfoMibsGroup 5 } fsOspfAreaLsaDBSumEntry OBJECT-TYPE SYNTAX FSOspfAreaLsaDBSumEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry of this table." INDEX {fsOspfAreaLsaDBSumAreaId, fsOspfAreaLsaDBSumLsaType } ::= { fsOspfAreaLsaDBSumTable 1 } FSOspfAreaLsaDBSumEntry ::= SEQUENCE{ fsOspfAreaLsaDBSumAreaId IpAddress, fsOspfAreaLsaDBSumLsaType INTEGER, fsOspfAreaLsaDBSumCounts Counter32, fsOspfAreaLsaDBSumDeletes Counter32, fsOspfAreaLsaDBSumMaxage Counter32 } fsOspfAreaLsaDBSumAreaId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The area Id." ::= { fsOspfAreaLsaDBSumEntry 1 } fsOspfAreaLsaDBSumLsaType OBJECT-TYPE SYNTAX INTEGER { routerLink (1), networkLink (2), summaryLink (3), asSummaryLink (4), --asExternalLink (5), because in each area,type 5 lsa is no meaning --it's only meaning in one router -- multicastLink (6), not implement nssaExternalLink (7), subtotal(8) --subtotal is use for total counter for all type LSA in this area. } MAX-ACCESS read-only STATUS current DESCRIPTION "the entry's entry type." ::= { fsOspfAreaLsaDBSumEntry 2 } fsOspfAreaLsaDBSumCounts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " number os this type Lsa in this area , if this type Lsa does not exist,this field is 0." ::= { fsOspfAreaLsaDBSumEntry 3 } fsOspfAreaLsaDBSumDeletes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " number os this type Lsa which has been delete in this area , if this type Lsa is not been deleted,this field is 0" ::= { fsOspfAreaLsaDBSumEntry 4 } fsOspfAreaLsaDBSumMaxage OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " number of this type Lsa which has up to Maxage, if this type Lsa which has up to Maxage does not exist, this field is 0" ::= { fsOspfAreaLsaDBSumEntry 5 } --fs Ospf Lsa Database total summary table fsOspfLsaDBSumTable OBJECT-TYPE SYNTAX SEQUENCE OF FSOspfLsaDBSumEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LSA database total summary infromtion in the all areas ." ::= { fsOspfLsaDetailInfoMibsGroup 6 } fsOspfLsaDBSumEntry OBJECT-TYPE SYNTAX FSOspfLsaDBSumEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry of this table." INDEX { fsOspfLsaDBSumLsaType } ::= { fsOspfLsaDBSumTable 1 } FSOspfLsaDBSumEntry ::= SEQUENCE{ fsOspfLsaDBSumLsaType INTEGER, fsOspfLsaDBSumCounts Counter32, fsOspfLsaDBSumDeletes Counter32, fsOspfLsaDBSumMaxage Counter32 } fsOspfLsaDBSumLsaType OBJECT-TYPE SYNTAX INTEGER { routerLink (1), networkLink (2), summaryTotalLink (3), asSummaryTotalLink (4), asExternalLink (5), -- multicastLink (6), not implement nssaExternalLink (7), total(8) --subtotal is use for total counter for all type LSA in this router. } MAX-ACCESS read-only STATUS current DESCRIPTION "the table's entry type." ::= { fsOspfLsaDBSumEntry 1 } fsOspfLsaDBSumCounts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "total number of this type Lsa in all area ." ::= { fsOspfLsaDBSumEntry 2 } fsOspfLsaDBSumDeletes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " total number of this type Lsa deleted in all area ." ::= { fsOspfLsaDBSumEntry 3 } fsOspfLsaDBSumMaxage OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "total number of this type Lsa which has been up to max age in all area " ::= { fsOspfLsaDBSumEntry 4 } -- The OSPF Neighbor Table describes all neighbors in -- the locality of the subject router. fsOspfNeighborTable OBJECT-TYPE SYNTAX SEQUENCE OF FSOspfNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the neighbor detail infomation ." REFERENCE "ospfNbrTable in rfc1850" ::= { fsOspfMIBObjects 9 } fsOspfNeighborEntry OBJECT-TYPE SYNTAX FSOspfNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry of this table." INDEX { fsOspfNbrIpAddr, fsOspfNbrAddressLessIndex } ::= { fsOspfNeighborTable 1 } FSOspfNeighborEntry ::= SEQUENCE{ fsOspfNbrIpAddr IpAddress, fsOspfNbrAddressLessIndex Unsigned32, fsOspfNbrRtrId RouterID, fsOspfNbrOptions Unsigned32, fsOspfNbrPriority DesignatedRouterPriority, fsOspfNbrState INTEGER, fsOspfNbrEvents Counter32, fsOspfNbrLsRetransQLen Gauge32, fsOspfNbmaNbrStatus RowStatus, fsOspfNbmaNbrPermanence INTEGER, fsOspfNbrHelloSuppressed TruthValue, fsOspfNbrDeadTimeDueIn TimeTicks, fsOspfNbrNeighborUpTime TimeTicks, fsOspfNbrDR IpAddress, fsOspfNbrBDR IpAddress, fsOspfNbrArea IpAddress, fsOspfNbrRetransmissionNum Counter32, fsOspfNbrIfState INTEGER } fsOspfNbrIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address this neighbor(neighbor's interface IP address) is using in its IP Source Address. Note that, on addressless links, this will not be 0.0.0.0, but the ad- dress of another of the neighbor's interfaces." ::= { fsOspfNeighborEntry 1 } fsOspfNbrAddressLessIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "On an interface having an IP Address, zero. On addressless interfaces, the corresponding value of ifIndex in the Internet Standard MIB. On row creation, this can be derived from the instance." ::= { fsOspfNeighborEntry 2 } fsOspfNbrRtrId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "A 32-bit integer (represented as a type IpAd- dress) uniquely identifying the neighboring router in the Autonomous System." ::= { fsOspfNeighborEntry 3 } fsOspfNbrOptions OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "A Bit Mask corresponding to the neighbor's op- tions field. Bit 0, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric. Bit 1, if set, indicates that the associated area accepts and operates on external informa- tion; if zero, it is a stub area. Bit 2, if set, indicates that the system is ca- pable of routing IP Multicast datagrams; i.e., that it implements the Multicast Extensions to OSPF. Bit 3, if set, indicates that the associated area is an NSSA. These areas are capable of carrying type 7 external advertisements, which are translated into type 5 external advertise- ments at NSSA borders." REFERENCE "OSPF Version 2, Section 12.1.2 Options" ::= { fsOspfNeighborEntry 4 } fsOspfNbrPriority OBJECT-TYPE SYNTAX DesignatedRouterPriority MAX-ACCESS read-only STATUS current DESCRIPTION "The priority of this neighbor in the designat- ed router election algorithm. The value 0 sig- nifies that the neighbor is not eligible to be- come the designated router on this particular network." ::= { fsOspfNeighborEntry 5 } fsOspfNbrState OBJECT-TYPE SYNTAX INTEGER { down (1), attempt (2), init (3), twoWay (4), exchangeFS (5), exchange (6), loading (7), full (8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The State of the relationship with this Neigh- bor." REFERENCE "OSPF Version 2, Section 10.1 Neighbor States" ::= { fsOspfNeighborEntry 6 } fsOspfNbrEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this neighbor relationship has changed state, or an error has occurred." ::= { fsOspfNeighborEntry 7 } fsOspfNbrLsRetransQLen OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current length of the retransmission queue." ::= { fsOspfNeighborEntry 8 } fsOspfNbmaNbrStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-only STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { fsOspfNeighborEntry 9 } fsOspfNbmaNbrPermanence OBJECT-TYPE SYNTAX INTEGER { dynamic (1), -- learned through protocol permanent (2) -- configured address } MAX-ACCESS read-only STATUS current DESCRIPTION "This variable displays the status of the en- try. 'dynamic' and 'permanent' refer to how the neighbor became known." ::= { fsOspfNeighborEntry 10 } fsOspfNbrHelloSuppressed OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether Hellos are being suppressed to the neighbor" ::= { fsOspfNeighborEntry 11 } fsOspfNbrDeadTimeDueIn OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "if in this interval ,hello packet is not been received , the neighbor is recognized dead.if received,it will recovery the dead time which has been setted." ::= { fsOspfNeighborEntry 12 } fsOspfNbrNeighborUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "the time that the neighbor has been up." ::= { fsOspfNeighborEntry 13 } fsOspfNbrDR OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "the Designated Router of this neighbor." ::= { fsOspfNeighborEntry 14 } fsOspfNbrBDR OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "the Backup Designated Router of this neighbor." ::= { fsOspfNeighborEntry 15 } fsOspfNbrArea OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "the area where the neighbor is in." ::= { fsOspfNeighborEntry 16 } fsOspfNbrRetransmissionNum OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "the Retransmission times." ::= { fsOspfNeighborEntry 17 } fsOspfNbrIfState OBJECT-TYPE SYNTAX INTEGER { other(0), designatedRouter (1), backupDesignatedRouter (2), otherDesignatedRouter (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The neighbor's interface State which connected to local router." ::= { fsOspfNeighborEntry 18 } --OSPF border routing information fsOspfRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF FSOspfRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entity's OSPF border routing table." ::= { fsOspfMIBObjects 10 } fsOspfRouteEntry OBJECT-TYPE SYNTAX FSOspfRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A route to a destination." INDEX { fsOspfRouteDest, fsOspfRouteArea, fsOspfRouteNextHop } ::= { fsOspfRouteTable 1 } FSOspfRouteEntry ::= SEQUENCE { fsOspfRouteDest IpAddress, fsOspfRouteArea IpAddress, fsOspfRouteNextHop IpAddress, fsOspfRouteCost Unsigned32, fsOspfRouteType INTEGER, fsOspfRouteDRType INTEGER, fsOspfRouteSpfNo Counter32 } fsOspfRouteDest OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Router ID of the destination." ::= { fsOspfRouteEntry 1 } fsOspfRouteArea OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The area ID of the area from which this route is learned." ::= { fsOspfRouteEntry 2 } fsOspfRouteNextHop OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Next hop toward the destination." ::= { fsOspfRouteEntry 3 } fsOspfRouteCost OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " Cost of using this route." ::= { fsOspfRouteEntry 4 } fsOspfRouteDRType OBJECT-TYPE SYNTAX INTEGER { abr(1), asbr(2), both(3) --abr and asbr } MAX-ACCESS read-only STATUS current DESCRIPTION "The router type of the destination; it is either an ABR or ASBR or both." ::= { fsOspfRouteEntry 5 } fsOspfRouteType OBJECT-TYPE SYNTAX INTEGER { intral-area-route(1), inter-area-route(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "this field indicate this route is an intral area route or inter area route." ::= { fsOspfRouteEntry 6 } fsOspfRouteSpfNo OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The internal number of the shortest path first (SPF) calculation that installs this route." ::= { fsOspfRouteEntry 7 } -- conformance information fsOspfMIBConformance OBJECT IDENTIFIER ::= { fsOspfMIB 2 } fsOspfMIBCompliances OBJECT IDENTIFIER ::= { fsOspfMIBConformance 1 } fsOspfMIBGroups OBJECT IDENTIFIER ::= { fsOspfMIBConformance 2 } -- compliance statements fsOspfMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the FS OSPF MIB" MODULE -- this module MANDATORY-GROUPS { fsOspfBaseMIBGroup, fsOspfAreaMIBGroup, fsOspfLsaMIBGroup, fsOspfIfMIBGroup, fsOspfVirtMIBGroup, fsOspfNeighborMIBGroup, fsOspfRouteInfoMIBGroup } ::= { fsOspfMIBCompliances 1 } -- units of conformance fsOspfBaseMIBGroup OBJECT-GROUP OBJECTS { fsOspfMiniLsaInterval , fsOspfMiniLsaArrival , fsOspfAreasNum , fsOspfNormalAreasNum , fsOspfStubAreasNum , fsOspfNssaAreasNum , fsOspfSpfDelay , fsOspfSpfHoldTime , fsOspfAutoCostRefBandWidthRef , fsOspfLsaGroupPacing , fsOspfInterDistance , fsOspfIntraDistance , fsOspfExternDistance , fsOspfLogAdjChangeNotify , fsOspfPassiveStatus , fsOspfRFC1583Compatibility , fsOspfRouteRedisDefMetricVal } STATUS current DESCRIPTION "A collection of general objects providing OSPF managment." ::= { fsOspfMIBGroups 1 } fsOspfAreaMIBGroup OBJECT-GROUP OBJECTS { fsOspfAreaId, fsOspfAuthType, fsOspfImportAsExtern, fsOspfSpfRuns, fsOspfAreaBdrRtrCount, fsOspfAsBdrRtrCount, fsOspfAreaLsaCount, fsOspfAreaLsaCksumSum, fsOspfAreaSummary, fsOspfAreaStatus, fsOspfAreaInterfaceNum, fsOspfAreaNssaIsRedistribution, fsOspfAreaNssaIsDefInfoOriginate, fsOspfNetWorkAreaID, fsOspfNetWorkAddress, fsOspfNetWorkMask, fsOspfNetWorkStatus } STATUS current DESCRIPTION "A collection of area objects providing OSPF managment." ::= { fsOspfMIBGroups 2 } fsOspfLsaMIBGroup OBJECT-GROUP OBJECTS { fsOspfLsdbAreaId, fsOspfLsdbType, fsOspfLsdbLsid, fsOspfLsdbRouterId, fsOspfLsdbSequence, fsOspfLsdbAge, fsOspfLsdbChecksum, fsOspfLsdbAdvertisement, fsOspfLsdbLinkNum, fsOspfLsdbPacketLength, fsOspfSummaryLsaNetworkMask, fsOspfSummaryLsaTos0Metric, fsOspfNssaLsaDetailMetricType, fsOspfNssaLsaDetailForwardAddr , fsOspfNssaLsaDetailRouteTag , fsOspfLsdbOption, fsOspfExtLsdbType, fsOspfExtLsdbLsid, fsOspfExtLsdbRouterId, fsOspfExtLsdbSequence, fsOspfExtLsdbAge, fsOspfExtLsdbChecksum, fsOspfExtLsdbAdvertisement, fsOspfExtLsdbNetworkMask, fsOspfExtLsdbMetricType, fsOspfExtLsdbForwardAddr, fsOspfExtLsdbRouteTag, fsOspfExtLsdbMetric, fsOspfExtLsdbOption, fsOspfExtLsdbPacketLength, fsOspfRouterLsaDetailLinkID, fsOspfRouterLsaDetailLinkType, fsOspfRouterLsaDetailLinkData, fsOspfRouterLsaDetailTos0Metric, fsOspfNetWorkLsaDetailAttachedRouter, fsOspfNetWorkLsaDetailNetworkMask, fsOspfAreaLsaDBSumAreaId, fsOspfAreaLsaDBSumLsaType, fsOspfAreaLsaDBSumCounts , fsOspfAreaLsaDBSumDeletes, fsOspfAreaLsaDBSumMaxage, fsOspfLsaDBSumLsaType, fsOspfLsaDBSumCounts, fsOspfLsaDBSumDeletes, fsOspfLsaDBSumMaxage } STATUS current DESCRIPTION "A collection of OSPF Link State Database objects providing OSPF managment." ::= { fsOspfMIBGroups 3 } fsOspfIfMIBGroup OBJECT-GROUP OBJECTS { fsOspfIfIpAddress, fsOspfAddressLessIf, fsOspfIfAreaId, fsOspfIfType, fsOspfIfAdminStat, fsOspfIfRtrPriority, fsOspfIfTransitDelay, fsOspfIfRetransInterval, fsOspfIfHelloInterval, fsOspfIfRtrDeadInterval, fsOspfIfPollInterval, fsOspfIfState, fsOspfIfDesignatedRouter, fsOspfIfBackupDesignatedRouter, fsOspfIfEvents, fsOspfIfAuthType, fsOspfIfAuthKey, fsOspfIfStatus, fsOspfIfMulticastForwarding, fsOspfIfDemand, fsOspfIfDatabaseFilterAllOut, fsOspfIfDesignateRouterId , fsOspfIfBackupDesignateRouterId , -- fsOspfIfMd5AuthKeyId, fsOspfIfWaitInternal, fsOspfIfPassiveStatus, fsOspfIfCurrentUsedMd5AuthKeyId, fsOspfIfMd5AuthKeyIf, fsOspfIfMd5AuthKeyId, fsOspfIfMd5AuthKey, fsOspfIfMd5AuthKeySt } STATUS current DESCRIPTION "A collection of OSPF interface managment." ::= { fsOspfMIBGroups 4 } fsOspfVirtMIBGroup OBJECT-GROUP OBJECTS { fsOspfVirtIfAreaId, fsOspfVirtIfNeighbor, fsOspfVirtIfTransitDelay, fsOspfVirtIfRetransInterval, fsOspfVirtIfHelloInterval, fsOspfVirtIfRtrDeadInterval, fsOspfVirtIfState, fsOspfVirtIfEvents, fsOspfVirtIfAuthType, fsOspfVirtIfAuthKey, fsOspfVirtIfStatus, fsOspfVirtCost, fsOspfVirtNativeIfIndex, fsOspfVirtLinkState, fsOspfVirtHelloDueIn, fsOspfVirtIfMd5AuthKeyAreaId, fsOspfVirtIfMd5AuthKeyNeighbor, fsOspfVirtIfMd5AuthKeyId, fsOspfVirtIfMd5AuthKey, fsOspfVirtIfMd5AuthKeySt, fsOspfVirtCurrentUsedMd5AuthKeyId } STATUS current DESCRIPTION "A collection of OSPF Virtual Link managment." ::= { fsOspfMIBGroups 5 } fsOspfNeighborMIBGroup OBJECT-GROUP OBJECTS { fsOspfNbrIpAddr, fsOspfNbrAddressLessIndex, fsOspfNbrRtrId, fsOspfNbrOptions, fsOspfNbrPriority, fsOspfNbrState, fsOspfNbrEvents, fsOspfNbrLsRetransQLen, fsOspfNbmaNbrStatus, fsOspfNbmaNbrPermanence, fsOspfNbrHelloSuppressed, fsOspfNbrDeadTimeDueIn, fsOspfNbrNeighborUpTime, fsOspfNbrDR, fsOspfNbrBDR, fsOspfNbrArea, fsOspfNbrRetransmissionNum } STATUS current DESCRIPTION "A collection of OSPF Neighbor information." ::= { fsOspfMIBGroups 6 } fsOspfRouteInfoMIBGroup OBJECT-GROUP OBJECTS { fsOspfRouteType, fsOspfRouteDest, fsOspfRouteNextHop, fsOspfRouteCost, fsOspfRouteDRType, fsOspfRouteArea, fsOspfRouteSpfNo } STATUS current DESCRIPTION "A collection of OSPF route information." ::= { fsOspfMIBGroups 7 } -- ------------------------------------------------------------- -- Compliance statements -- ------------------------------------------------------------- ospfMIBConformance OBJECT IDENTIFIER ::= { fsOspfMIB 3 } ospfMIBCompliances OBJECT IDENTIFIER ::= { ospfMIBConformance 1 } ospfExternCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for device support of OSPF services." MODULE -- OBJECT ospfASBdrRtrStatus -- MIN-ACCESS read-only -- DESCRIPTION "Write access is not required." -- -- OBJECT ospfTOSSupport -- MIN-ACCESS read-only -- DESCRIPTION "Write access is not required." -- -- OBJECT ospfExtLsdbLimit -- MIN-ACCESS read-only -- DESCRIPTION "Write access is not required." -- -- OBJECT ospfMulticastExtensions -- MIN-ACCESS read-only -- DESCRIPTION "Write access is not required." -- -- OBJECT ospfExitOverflowInterval -- MIN-ACCESS read-only -- DESCRIPTION "Write access is not required." -- -- OBJECT ospfDemandExtensions -- MIN-ACCESS read-only -- DESCRIPTION "Write access is not required." -- -- OBJECT ospfIfAreaId -- MIN-ACCESS read-only -- DESCRIPTION "Write access is not required." -- -- OBJECT ospfIfStatus -- MIN-ACCESS read-only -- DESCRIPTION "Create access is not required." -- -- -- OBJECT ospfStubMetric -- MIN-ACCESS read-write -- DESCRIPTION "Create access is not required." -- -- OBJECT ospfStubStatus -- MIN-ACCESS read-only -- DESCRIPTION "Write access is not required." -- -- OBJECT ospfStubMetricType -- MIN-ACCESS read-write -- DESCRIPTION "Create access is not required." -- -- OBJECT ospfIfAdminStat -- MIN-ACCESS read-only -- DESCRIPTION "Write access is not required." -- -- OBJECT ospfNbmaNbrStatus -- MIN-ACCESS read-only -- DESCRIPTION "Read-create access is not required." -- -- OBJECT ospfNbrPriority -- MIN-ACCESS read-only -- DESCRIPTION "Read-create access is not required." -- -- OBJECT ospfIfPollInterval -- MIN-ACCESS read-only -- DESCRIPTION "Read-create access is not required." -- -- OBJECT ospfIfTransitDelay -- SYNTAX Unsigned32 (1..65535) -- DESCRIPTION "Range of value is changed." -- -- OBJECT ospfIfRetransInterval -- SYNTAX Unsigned32 (1..65535) -- DESCRIPTION "Range of value is changed." -- -- OBJECT ospfVirtIfTransitDelay -- SYNTAX Unsigned32 (1..65535) -- DESCRIPTION "Range of value is changed." -- -- OBJECT ospfIfType -- SYNTAX INTEGER { -- broadcast (1), -- nbma (2), -- pointToPoint (3), -- pointToMultipoint (5), -- loopback(6) -- } -- DESCRIPTION "add type 'loopback'." -- -- OBJECT ospfVirtIfRetransInterval -- SYNTAX Unsigned32 (1..65535) -- DESCRIPTION "Range of value is changed." OBJECT fsOspfVirtIfRtrDeadInterval SYNTAX PositiveInteger DESCRIPTION "default value change from 60 to 40." ::= { ospfMIBCompliances 1 } END