-- ***************************************************************** -- FS-INTERFACE-MIB.mib: FS interface MIB file -- -- March 2002, Wuzg -- -- Copyright (c) 2002 by FS.COM Inc.. -- All rights reserved. -- -- ***************************************************************** -- FS-INTERFACE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32, OBJECT-TYPE, Counter32, Counter64, Unsigned32, IpAddress FROM SNMPv2-SMI RowStatus, DisplayString, PhysAddress, DateAndTime, MacAddress FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ConfigStatus, IfIndex FROM FS-TC EnabledStatus FROM P-BRIDGE-MIB ifIndex FROM RFC1213-MIB Gauge, TimeTicks FROM RFC1155-SMI fsMgmt FROM FS-SMI IANAifType FROM IANAifType-MIB VlanId FROM Q-BRIDGE-MIB InterfaceIndex FROM IF-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- RFC3411 InetAddressType, InetAddress FROM INET-ADDRESS-MIB; -- RFC4001 fsInterfaceMIB MODULE-IDENTITY LAST-UPDATED "201002010000Z" ORGANIZATION "FS.COM Inc.." CONTACT-INFO " Tel: 400-865-2852 E-mail: https://www.fs.com/live_chat_service_mail.html" DESCRIPTION "This module defines fs interface mibs." REVISION "201002010000Z" DESCRIPTION "Add a table about vlan." REVISION "200203200000Z" DESCRIPTION "Initial version of this MIB module." ::= { fsMgmt 10} fsIfConfigMIBObjects OBJECT IDENTIFIER ::= { fsInterfaceMIB 1 } fsIfTable OBJECT-TYPE SYNTAX SEQUENCE OF FSIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "list of interface basic configuration objects." ::= { fsIfConfigMIBObjects 1 } fsIfEntry OBJECT-TYPE SYNTAX FSIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry contains interface basic configurations." INDEX { fsIfIndex } ::= { fsIfTable 1 } FSIfEntry ::= SEQUENCE { fsIfIndex IfIndex, fsIfPortType INTEGER, fsIfFlowControlAdminStatus INTEGER, fsIfFlowControlOperStatus EnabledStatus, fsIfAdminSpeed INTEGER, fsIfAdminDuplex INTEGER, fsIfOperSpeed INTEGER, fsIfOperDuplex INTEGER, fsIfManageStatus EnabledStatus, fsIfIpBroadcast IpAddress, fsIfLayer INTEGER, fsIfMode INTEGER, fsIfCounterClear Integer32, fsIfEntryStatus ConfigStatus, fsIfMediumType INTEGER, fsIfDownCounter Counter32, fsIfInOctets Counter64, fsIfOutOctets Counter64, fsIfBcastInhibit INTEGER, fsIfNegotiation INTEGER, fsIfPhysAddress MacAddress, fsIfAdminSpeedRW INTEGER, fsIfAdminDuplexRW INTEGER, fsIfModeRW INTEGER, fsIfSpeed Gauge, fsifAdminStatus INTEGER, fsifOperStatus INTEGER, fsIfInNUcastPkts Counter64, fsIfOutNUcastPkts Counter64, fsIfUpDownTimes Counter32, fsifAdminStatusw INTEGER, fsifOperStatusw INTEGER, fsifSpeedw Integer32, fsifMacAddress MacAddress, fsifLastChange TimeTicks, fsIfInPkts Counter64, fsIfDiscard Counter64, fsIfBandwidthUsage DisplayString, fsIfInBitsRate Counter64, fsIfInPktRate Counter64, fsIfOutBitsRate Counter64, fsIfOutPktRate Counter64, fsIfInBandwidthUsage DisplayString, fsIfOutBandwidthUsage DisplayString, fsIfInErrorPktsRate DisplayString, fsIfOutErrorPktsRate DisplayString, fsIfInDropPktsRate DisplayString, fsIfOutDropPktsRate DisplayString, fsIfOutNoBuffer Counter64, fsIfOutPkts Counter64 } fsIfIndex OBJECT-TYPE SYNTAX IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION " " ::= { fsIfEntry 1 } fsIfPortType OBJECT-TYPE SYNTAX INTEGER { unknown(1), port10M100MBASETX(2), port100MBASEFXL(3), port100MBASEFXS(4), port1000MBASESX(5), port1000MBASELX(6), port1000MBASETX(7), portGBIC(8), port100MBASEFX(9), port1000MBASEFX(10), portSFP(11), port10GBASESR(12), port10GBASELR(13), port10GBASEER(14), port10GBASELX4(15), port10GBASESW(16), port10GBASELW(17), port10GBASEEW(18), port10GBASE(19), port40GBASEKR(20), port40GBASECR(21), port40GBASELR(22), port40GBASESR(23), port40GBASE(24), port100GBASECR(25), port100GBASESR(26), port100GBASELR(27), port100GBASEER(28), port100GBASE(29), port155MCPOS(50), port622MCPOS(51), port2G5CPOS(52), port10GCPOS(53), port155MPOS(54), port622MPOS(55), port2G5POS(56), port10GPOS(57), port155MATM(58), port622MATM(59), port2G5ATM(60), port10GATM(61), portE1ELC(62), port20GBASE(63), port25GBASE(64), port2500MBASE(65), port5000MBASE(66) } MAX-ACCESS read-only STATUS current DESCRIPTION "Port type of this port, list as above. port100MBASEFX indicates that port is port100MBASEFXL or port100MBASEFXS, and system doesn't distinguish. port1000MBASEFX indicates that port is port1000MBASEFLX or port1000MBASEFSX, and system doesn't distinguish. This attribute apply physical port" ::= { fsIfEntry 2 } fsIfFlowControlAdminStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2), autonego(3), unknown(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Flow control of a port management status. This attribute apply physical port and aggreate port" ::= { fsIfEntry 3 } fsIfFlowControlOperStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-only STATUS current DESCRIPTION "Oper status: after the negotiation between two ports connetted the flow contrl status. This attribute apply physical port and aggreate port" ::= { fsIfEntry 4 } fsIfAdminSpeed OBJECT-TYPE SYNTAX INTEGER { speed10Mb(1), speed100Mb(2), speed1000Mb(3), autonego(4), speed10Gb(5), unknown(6), speed40Gb(7), speed100Gb(8) } MAX-ACCESS read-create STATUS current DESCRIPTION "port speed settings. This attribute apply physical port and aggreate port" ::= { fsIfEntry 5 } fsIfAdminDuplex OBJECT-TYPE SYNTAX INTEGER { full(1), half(2), autonego(3), unknown(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "port duplex settings. This attribute apply physical port and aggreate port" ::= { fsIfEntry 6 } fsIfOperSpeed OBJECT-TYPE SYNTAX INTEGER { speed10Mb(1), speed100Mb(2), speed1000Mb(3), unknown(4), speed10Gb(5), speed40Gb(6), speed100Gb(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "After two port have negotiated the speed status,and this object is the working speed status. while the port link status is down , then the speed status is unknown(4). This attribute apply physical port and aggreate port" ::= { fsIfEntry 7 } fsIfOperDuplex OBJECT-TYPE SYNTAX INTEGER { full(1), half(2), unknown(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "After two port have negotiated the duplex status, and this object is the working duplex status. while the port link status is down , then the speed status is unknown(3). This attribute apply physical port and aggreate port" ::= { fsIfEntry 8 } fsIfManageStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Management status of the interface." DEFVAL { enabled } ::={fsIfEntry 9} fsIfIpBroadcast OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Broadcast address of the interface. if broadcast address not configured on interface, return 0.0.0.0" ::= { fsIfEntry 10 } fsIfLayer OBJECT-TYPE SYNTAX INTEGER { layer-2(1), -- the interface is a interface of L2 layer-3(2) -- the interface is a interface of L3 } MAX-ACCESS read-create STATUS current DESCRIPTION "" ::= { fsIfEntry 11 } fsIfMode OBJECT-TYPE SYNTAX INTEGER { access(1), -- the mode of interface is access port trunk(2), -- the mode of interface is trunk port dot1q-tunnel(3), -- the mode of interface is 802.1q tunnel port hybrid(4), -- the mode of interface is hybrid port other(5), -- other mode uplink(6), -- the mode of interface is uplink port host(7), -- the mode of interface is private-vlan host port promiscuous(8) -- the mode of interface is private-vlan promiscuous port } MAX-ACCESS read-create STATUS current DESCRIPTION "This value is meaning for only physical port and aggreate port" ::= { fsIfEntry 12 } fsIfCounterClear OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Setting its to any value but 0, will clear counters of this interface. Setting its value to 0 will cause no action of the agent. and when query will always return 0. " ::= { fsIfEntry 13 } fsIfEntryStatus OBJECT-TYPE SYNTAX ConfigStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Status of this entry, set this object to valid will create a interface, and set its value to invalid will delete the interface of this entry." ::= { fsIfEntry 14 } fsIfMediumType OBJECT-TYPE SYNTAX INTEGER { unknown(0), copper(1), fiber(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Port medium type of this port,fiber or copper." ::= { fsIfEntry 15 } fsIfDownCounter OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counters of linkdown times of the interface." ::= { fsIfEntry 16 } fsIfInOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfEntry 17 } fsIfOutOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfEntry 18 } fsIfBcastInhibit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The percentage of the broadcast storm restraint on the interface." ::= { fsIfEntry 19 } fsIfNegotiation OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "The negotiation status of the interface." ::= { fsIfEntry 20 } fsIfPhysAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The interface's address at its protocol sub-layer. For example, for an 802.x interface, this object normally contains a MAC address. The interface's media-specific MIB must define the bit and byte ordering and the format of the value of this object. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length." ::= { fsIfEntry 21 } fsIfAdminSpeedRW OBJECT-TYPE SYNTAX INTEGER { speed10Mb(1), speed100Mb(2), speed1000Mb(3), autonego(4), speed10Gb(5), unknown(6), speed40Gb(7), speed100Gb(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "port speed settings. This attribute apply physical port and aggreate port" ::= { fsIfEntry 22 } fsIfAdminDuplexRW OBJECT-TYPE SYNTAX INTEGER { full(1), half(2), autonego(3), unknown(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "port duplex settings. This attribute apply physical port and aggreate port" ::= { fsIfEntry 23 } fsIfModeRW OBJECT-TYPE SYNTAX INTEGER { access(1), -- the mode of interface is access port trunk(2), -- the mode of interface is trunk port dot1q-tunnel(3), -- the mode of interface is 802.1q tunnel port hybrid(4), -- the mode of interface is hybrid port other(5), -- other mode uplink(6), -- the mode of interface is uplink port host(7), -- the mode of interface is private-vlan host port promiscuous(8) -- the mode of interface is private-vlan promiscuous port } MAX-ACCESS read-write STATUS current DESCRIPTION "This value is meaning for only physical port and aggreate port" ::= { fsIfEntry 24 } fsIfSpeed OBJECT-TYPE SYNTAX Gauge MAX-ACCESS read-only STATUS current DESCRIPTION "An estimate of the interface's current bandwidth in units of Mbits per second." ::= { fsIfEntry 25 } fsifAdminStatus OBJECT-TYPE SYNTAX INTEGER { adminup(1), admindown(2), admintest(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "the interface keeps the admin state ." ::= { fsIfEntry 26 } fsifOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), test(3), unknow(4), dormant(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "the interface keeps the oper state ." ::= { fsIfEntry 27} fsIfInNUcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter of receiving packets contain BROADCAST and PACKET_MULTICAST ." ::= { fsIfEntry 28 } fsIfOutNUcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter of sending packets contain BROADCAST and PACKET_MULTICAST ." ::= { fsIfEntry 29 } fsIfUpDownTimes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counters of linkup and linkdown times of the interface." ::= { fsIfEntry 30 } fsifAdminStatusw OBJECT-TYPE SYNTAX INTEGER { up(0), admindown(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "The desired state of the interface. When a managed system initializes, all interfaces start with ifAdminStatus in the admindown(1) state. As a result of either explicit management action or per configuration information retained by the managed system, ifAdminStatus is then changed to either the up(0) states (or remains in the admindown(1) state)." ::= { fsIfEntry 31 } fsifOperStatusw OBJECT-TYPE SYNTAX INTEGER { up(0), down(1), admindown(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational state of the interface. If fsApIfAdminStatus is admindown(2) then fsApIfOperStatus should be admindown(2). If fsApIfAdminStatus is changed to up(0) then fsApIfOperStatus should change to up(0) . it should remain in the down(1) state if and only if there is a fault that prevents it from going to the up(0) state; " ::= { fsIfEntry 32 } fsifSpeedw OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "An estimate of the interface's current bandwidth in units of Mbits per second." ::= { fsIfEntry 33 } fsifMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The interface's address at its protocol sub-layer. For example, for an 802.x interface, this object normally contains a MAC address. The interface's media-specific MIB must define the bit and byte ordering and the format of the value of this object. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length." ::= { fsIfEntry 34 } fsifLastChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The length of the time that comes current state ." ::= { fsIfEntry 35 } fsIfInPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets received on this interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfEntry 36 } fsIfDiscard OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bound packets which were chosen to be discarded even though no errors. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfEntry 37 } fsIfBandwidthUsage OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Current bandwidth utilization of interface." ::= { fsIfEntry 38 } fsIfInBitsRate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The average input packet-rate over a period of time(configuration by interface command 'load-interval') in bits per second on this interface." ::= { fsIfEntry 39 } fsIfInPktRate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The average input packet-rate over a period of time(configuration by interface command 'load-interval') in packets per second on this interface." ::= { fsIfEntry 40 } fsIfOutBitsRate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The average output packet-rate over a period of time(configuration by interface command 'load-interval') in bits per second on this interface." ::= { fsIfEntry 41 } fsIfOutPktRate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The average output packet-rate over a period of time(configuration by interface command 'load-interval') in packets per second on this interface." ::= { fsIfEntry 42 } fsIfInBandwidthUsage OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "RX bandwidth utilization ratio of interface." ::= { fsIfEntry 43 } fsIfOutBandwidthUsage OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "TX bandwidth utilization ratio of interface." ::= { fsIfEntry 44 } fsIfInErrorPktsRate OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Input packet error rate." ::= { fsIfEntry 45 } fsIfOutErrorPktsRate OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Output packet error rate." ::= { fsIfEntry 46 } fsIfInDropPktsRate OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Input packet discarded rate." ::= { fsIfEntry 47 } fsIfOutDropPktsRate OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Output packet discarded rate." ::= { fsIfEntry 48 } fsIfOutNoBuffer OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Ouyput drop packet rate on this interface due to resource lack." ::= { fsIfEntry 49 } fsIfOutPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets sent on this interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfEntry 50 } fsIfIpTable OBJECT-TYPE SYNTAX SEQUENCE OF FSIfIpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of interface ip configuration entries." ::= { fsIfConfigMIBObjects 2} fsIfIpEntry OBJECT-TYPE SYNTAX FSIfIpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing configuration information applicable to a Layer3 interface." INDEX { fsIfIpIfIndex, fsIfIpId, fsIfIp} ::= { fsIfIpTable 1 } FSIfIpEntry ::= SEQUENCE { fsIfIpIfIndex IfIndex, fsIfIpId INTEGER, fsIfIp IpAddress, fsIfIpMask IpAddress, fsIfIpEntryStatus RowStatus } fsIfIpIfIndex OBJECT-TYPE SYNTAX IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "A unique value, for each Layer3 interface." ::= { fsIfIpEntry 1 } fsIfIpId OBJECT-TYPE SYNTAX INTEGER{ primary(1), -- primary ip address of Layer3 interface secondary(2) -- secondary ip address of Layer3 interface } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of interface ip address." ::= { fsIfIpEntry 2 } fsIfIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Ip address of the interface fsIfIndex refer to." ::= { fsIfIpEntry 3 } fsIfIpMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Ip mask of the interface ip address." ::= { fsIfIpEntry 4 } fsIfIpEntryStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "entry status of this entry. and the means in this enviraments can reffer to the text-convention definition of the RowStatus." ::= { fsIfIpEntry 5 } fsIfStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF FSIfStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "list of interface status. Status information include some error state and result of examining to the interface,etc." ::= { fsIfConfigMIBObjects 3 } fsIfStatusEntry OBJECT-TYPE SYNTAX FSIfStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry contains interface status information." INDEX { fsIfStatusIndex } ::= { fsIfStatusTable 1 } FSIfStatusEntry ::= SEQUENCE { fsIfStatusIndex IfIndex, fsIfStatusLoopBackExamine Integer32, fsIfErrorStatus INTEGER, fsIfLineDetect Integer32 } fsIfStatusIndex OBJECT-TYPE SYNTAX IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION " " ::= { fsIfStatusEntry 1 } fsIfStatusLoopBackExamine OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Setting its to any value but 0, will Checking whether this port or aggreate can receive and send packets normally, It indicates that port or aggreate is normal if opertion is success. Setting its value to 0 will cause no action of the agent. and when query will always return 0. This attribute apply physical port and aggreate port" ::= { fsIfStatusEntry 2 } fsIfErrorStatus OBJECT-TYPE SYNTAX INTEGER { no-error(1), -- port is enabled normal err-disable-bpduguard(2), -- port is disabled by port receive BPDU packet when port -- enable BPDU guard err-disable-ptsecurity(3) -- port is disabled by port security is violatd } MAX-ACCESS read-only STATUS current DESCRIPTION "Port's error status information" ::= { fsIfStatusEntry 3 } fsIfLineDetect OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "When reading this object, system detects the quality of line connecting the port. Detect whether the line is broken or short circuit or not. The meaning of the obtained value: Return value=N*10000000+M N stands for the line state (0: perfect; 1: break; 2: short circuit) M stands for the location of the break or short circuit in the line(distance from the switch port, in metre) If the line is perfect, the value is zero." ::= { fsIfStatusEntry 4 } fsGlobalIfDisableRecovery OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Setting its to any value but 0, the interfaces which is shutted down by some error happened will recovery from disabled status . Setting its value to 0 will cause no action of the agent. and when query will always return 0. This attribute apply physical port and aggreate port" ::= { fsIfConfigMIBObjects 4 } -- -- portType Choose -- fsPortTypeChooseTable OBJECT-TYPE SYNTAX SEQUENCE OF FSPortTypeChooseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of entrance to choose port type." ::= { fsIfConfigMIBObjects 5 } fsPortTypeChooseEntry OBJECT-TYPE SYNTAX FSPortTypeChooseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entrance to choose port type." INDEX { fsPortTypeChooseIndex } ::= { fsPortTypeChooseTable 1 } FSPortTypeChooseEntry ::= SEQUENCE { fsPortTypeChooseIndex IfIndex, fsPortTypeChooseType INTEGER } fsPortTypeChooseIndex OBJECT-TYPE SYNTAX IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The logic port number." ::= { fsPortTypeChooseEntry 1 } fsPortTypeChooseType OBJECT-TYPE SYNTAX INTEGER { fiber(1), --priority of fiber port copper(2) --priority of copper port } MAX-ACCESS read-only STATUS current DESCRIPTION "The chosen port type. This object is used to choose one of the multiple physical ports of different types, when the same logical port is correspondent with them. Apply this attribute to the physical port only." ::= { fsPortTypeChooseEntry 2 } -- -- mtu -- fsIfMTUTable OBJECT-TYPE SYNTAX SEQUENCE OF FSIfMTUEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Access table of MTU on interface." ::= { fsIfConfigMIBObjects 6 } fsIfMTUEntry OBJECT-TYPE SYNTAX FSIfMTUEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Interfac MTU access." INDEX { fsIfMTUIndex } ::= { fsIfMTUTable 1 } FSIfMTUEntry ::= SEQUENCE { fsIfMTUIndex IfIndex, fsIfMTU Integer32 } fsIfMTUIndex OBJECT-TYPE SYNTAX IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Interface number" ::= { fsIfMTUEntry 1 } fsIfMTU OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Interface MTU." ::= { fsIfMTUEntry 2 } -- -- Available Bandwidth -- fsIfAvailableBWTable OBJECT-TYPE SYNTAX SEQUENCE OF FSIfAvailableBWEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Access table of Available Bandwidth on interface." ::= { fsIfConfigMIBObjects 7 } fsIfAvailableBWEntry OBJECT-TYPE SYNTAX FSIfAvailableBWEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Interfac available bandwidth access." INDEX { fsIfAvailableBWIfIndex } ::= { fsIfAvailableBWTable 1 } FSIfAvailableBWEntry ::= SEQUENCE { fsIfAvailableBWIfIndex IfIndex, fsIfAvailableBWIfBW Gauge } fsIfAvailableBWIfIndex OBJECT-TYPE SYNTAX IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Interface number" ::= { fsIfAvailableBWEntry 1 } fsIfAvailableBWIfBW OBJECT-TYPE SYNTAX Gauge MAX-ACCESS read-only STATUS current DESCRIPTION "Interface available bandwidth(bit)." ::= { fsIfAvailableBWEntry 2 } -- -- Creat Interface Vlan -- fsIfSVICreatTable OBJECT-TYPE SYNTAX SEQUENCE OF FSIfSVICreatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Access table of Available Bandwidth on interface." ::= { fsIfConfigMIBObjects 8 } fsIfSVICreatEntry OBJECT-TYPE SYNTAX FSIfSVICreatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Interfac available bandwidth access." INDEX { fsIfSVICreatVlanNum } ::= { fsIfSVICreatTable 1 } FSIfSVICreatEntry ::= SEQUENCE { fsIfSVICreatVlanNum Integer32, fsIfHandleSVI INTEGER } fsIfSVICreatVlanNum OBJECT-TYPE SYNTAX Integer32(1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "Interface Vlan number" ::= { fsIfSVICreatEntry 1 } fsIfHandleSVI OBJECT-TYPE SYNTAX INTEGER{create(0), delete(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "0 creat,1 delete." ::= { fsIfSVICreatEntry 2 } -- -- Get Physical Interface Number -- fsIfPhyIntNum OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of physical interfaces (regardless of their current state) present on this system." ::= { fsIfConfigMIBObjects 9 } -- -- Get Interface LinkUP Times -- fsIfLinkUPTimesTable OBJECT-TYPE SYNTAX SEQUENCE OF FSIfLinkUPTimesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Access table of Available Bandwidth on interface." ::= { fsIfConfigMIBObjects 10 } fsIfLinkUPTimesEntry OBJECT-TYPE SYNTAX FSIfLinkUPTimesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Interfac available bandwidth access." INDEX { fsInterfaceIndex } ::= { fsIfLinkUPTimesTable 1 } FSIfLinkUPTimesEntry ::= SEQUENCE { fsInterfaceIndex Integer32, fsIfLinkUPTimes INTEGER } fsInterfaceIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Interface Index" ::= { fsIfLinkUPTimesEntry 1 } fsIfLinkUPTimes OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Vlaues Of Linkup Times." ::= { fsIfLinkUPTimesEntry 2 } -- -- Interface encapsulation dot1q VLAN -- fsIfEncapsulationTable OBJECT-TYPE SYNTAX SEQUENCE OF FSIfEncapsulationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Access table of Encapsulation dot1q VLAN on interface." ::= { fsIfConfigMIBObjects 11 } fsIfEncapsulationEntry OBJECT-TYPE SYNTAX FSIfEncapsulationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Interfac encapsulation dot1q VLAN access." INDEX { fsIfEncapsulationIndex } ::= { fsIfEncapsulationTable 1 } FSIfEncapsulationEntry ::= SEQUENCE { fsIfEncapsulationIndex IfIndex, fsIfEncapsulationVlan VlanId } fsIfEncapsulationIndex OBJECT-TYPE SYNTAX IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization." ::= { fsIfEncapsulationEntry 1 } fsIfEncapsulationVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-write STATUS current DESCRIPTION "The value indicate the VID of the dot1q vlan encapsulation. The value 0 means de-encapsulation." ::= { fsIfEncapsulationEntry 2 } -- -- Get ap interface number -- fsApIfNumberTable OBJECT-TYPE SYNTAX SEQUENCE OF FSApIfNumberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Access table of ap interface number." ::= { fsIfConfigMIBObjects 12 } fsApIfNumberEntry OBJECT-TYPE SYNTAX FSApIfNumberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Interfac number of ap." INDEX { fsApPhyAddress } ::= { fsApIfNumberTable 1 } FSApIfNumberEntry ::= SEQUENCE { fsApPhyAddress PhysAddress, fsApIfNumber INTEGER, fsApIfPhyIntNum INTEGER } fsApPhyAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The ap's address at its protocol sub-layer. The ap's media-specific MIB must define the bit and byte ordering and the format of the value of this object. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length." ::= { fsApIfNumberEntry 1 } fsApIfNumber OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Vlaues Of interface number." ::= { fsApIfNumberEntry 2 } fsApIfPhyIntNum OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Vlaues Of physical interface number." ::= { fsApIfNumberEntry 3 } -- --fsApIfTable -- fsApIfTable OBJECT-TYPE SYNTAX SEQUENCE OF FSApIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of fsAp interface entries. The number of entries is given by the value of fsApIfNumber." ::= { fsIfConfigMIBObjects 13 } fsApIfEntry OBJECT-TYPE SYNTAX FSApIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing management information fsApplicable to a particular interface." INDEX { fsApPhysAddress, fsApIfIndex } ::= { fsApIfTable 1 } FSApIfEntry ::= SEQUENCE { fsApPhysAddress PhysAddress, fsApIfIndex IfIndex, fsApIfDescr DisplayString, fsApIfType IANAifType, fsApIfMtu INTEGER, fsApIfSpeed Gauge, fsApIfPhysAddress PhysAddress, fsApIfAdminStatus INTEGER, fsApIfOperStatus INTEGER, fsApIfLastChange TimeTicks, fsApIfInOctets Counter64, fsApIfInUcastPkts Counter64, fsApIfInNUcastPkts Counter64, fsApIfInDiscards Counter32, fsApIfInErrors Counter32, fsApIfInUnknownProtos Counter32, fsApIfOutOctets Counter64, fsApIfOutUcastPkts Counter64, fsApIfOutNUcastPkts Counter64, fsApIfOutDiscards Counter32, fsApIfOutErrors Counter32, fsApIfOutQLen Gauge, fsApIfLinkUPTimes INTEGER, fsApIfInDataOctets Counter64, fsApIfOutDataOctets Counter64, fsApIfMgmtUploadOctets Counter32, fsApIfMgmtDownloadOctets Counter32, fsApIfSpeedw Integer32, fsApIfMtuw Integer32, fsApIfPhysAddressw MacAddress, fsApIfInUcastPktsw Counter32, fsApIfInNUcastPktsw Counter32, fsApIfOutUcastPktsw Counter32, fsApIfOutNUcastPktsw Counter32, fsApIfLinkUPTimesw Counter32, fsApIfInPkts Counter64, fsApIfInFlow Counter32, fsApIfOutFlow Counter32, fsApIfInBrdcastPkts Counter64, fsApIfOutBrdcastPkts Counter64, fsApIfInMulcastPkts Counter64, fsApIfOutMulcastPkts Counter64, fsApIfInPayloadOctets Counter64, fsApIfOutPayloadOctets Counter64, fsApIfAlias DisplayString, fsApIfInDateRate Counter64, fsApIfOutDateRate Counter64, fsApifInNormalPkts Counter64, fsApIfOutPkts Counter64 } fsApPhysAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The ap's address at its protocol sub-layer. The ap's media-specific MIB must define the bit and byte ordering and the format of the value of this object. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length." ::= { fsApIfEntry 1 } fsApIfIndex OBJECT-TYPE SYNTAX IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization." ::= { fsApIfEntry 2 } fsApIfDescr OBJECT-TYPE SYNTAX DisplayString(SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software." ::= { fsApIfEntry 3 } fsApIfType OBJECT-TYPE SYNTAX IANAifType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of interface. Additional values for ifType are assigned by the Internet Assigned Numbers Authority (IANA), through updating the syntax of the IANAifType textual convention." ::= { fsApIfEntry 4 } fsApIfMtu OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The size of the largest packet which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface." ::= { fsApIfEntry 5 } fsApIfSpeed OBJECT-TYPE SYNTAX Gauge MAX-ACCESS read-only STATUS current DESCRIPTION "An estimate of the interface's current bandwidth in units of Mbits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth.For a sub-layer which has no concept of bandwidth, this object should be zero." ::= { fsApIfEntry 6 } fsApIfPhysAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The interface's address at its protocol sub-layer. For example, for an 802.x interface, this object normally contains a MAC address. The interface's media-specific MIB must define the bit and byte ordering and the format of the value of this object. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length." ::= { fsApIfEntry 7 } fsApIfAdminStatus OBJECT-TYPE SYNTAX INTEGER { up(1), admindown(2), testing(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The desired state of the interface. The testing(3) state indicates that no operational packets can be passed. When a managed system initializes, all interfaces start with ifAdminStatus in the admindown(2) state. As a result of either explicit management action or per configuration information retained by the managed system, ifAdminStatus is then changed to either the up(1) or testing(3) states (or remains in the admindown(2) state)." ::= { fsApIfEntry 8 } fsApIfOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), admindown(3), unknown(4), dormant(5), notPresent(6), lowerLayerDown(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational state of the interface. If fsApIfAdminStatus is admindown(2) then fsApIfOperStatus should be admindown(3). If fsApIfAdminStatus is changed to up(1) then fsApIfOperStatus should change to up(1) if the interface is ready to transmit and receive network traffic; it should change to dormant(5) if the interface is waiting for external actions (such as a serial line waiting for an incoming connection); it should remain in the down(2) state if and only if there is a fault that prevents it from going to the up(1) state; it should remain in the notPresent(6) state if the interface has missing (typically, hardware) components." ::= { fsApIfEntry 9 } fsApIfLastChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value." ::= { fsApIfEntry 10 } fsApIfInOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 11 } fsApIfInUcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 12 } fsApIfInNUcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime. This object is deprecated in favour of fsApIfInMulticastPkts and fsApIfInBroadcastPkts." ::= { fsApIfEntry 13 } fsApIfInDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 14 } fsApIfInErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 15 } fsApIfInUnknownProtos OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "For packet-oriented interfaces, the number of packets received via the interface which were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing the number of transmission units received via the interface which were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 16 } fsApIfOutOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 17 } fsApIfOutUcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 18 } fsApIfOutNUcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime. This object is deprecated in favour of ifOutMulticastPkts and fsApIfOutBroadcastPkts." ::= { fsApIfEntry 19 } fsApIfOutDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 20 } fsApIfOutErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 21 } fsApIfOutQLen OBJECT-TYPE SYNTAX Gauge MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The length of the output packet queue (in packets)." ::= { fsApIfEntry 22 } fsApIfLinkUPTimes OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Vlaues Of Linkup Times." ::= { fsApIfEntry 23 } fsApIfInDataOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The data octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 24 } fsApIfOutDataOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The data octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 25 } fsApIfMgmtUploadOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The upload octets received on the mgmt interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 26 } fsApIfMgmtDownloadOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The download octets transmitted out of the mgmt interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 27 } fsApIfSpeedw OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "An estimate of the interface's current bandwidth in units of Mbits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. For a sub-layer which has no concept of bandwidth, this object should be zero." ::= { fsApIfEntry 28 } fsApIfMtuw OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The size of the largest packet which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface." ::= { fsApIfEntry 29 } fsApIfPhysAddressw OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The interface's address at its protocol sub-layer. For example, for an 802.x interface, this object normally contains a MAC address. The interface's media-specific MIB must define the bit and byte ordering and the format of the value of this object. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length." ::= { fsApIfEntry 30 } fsApIfInUcastPktsw OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 31 } fsApIfInNUcastPktsw OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime. This object is deprecated in favour of fsApIfInMulticastPkts and fsApIfInBroadcastPkts." ::= { fsApIfEntry 32 } fsApIfOutUcastPktsw OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 33 } fsApIfOutNUcastPktsw OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime. This object is deprecated in favour of ifOutMulticastPkts and fsApIfOutBroadcastPkts." ::= { fsApIfEntry 34 } fsApIfLinkUPTimesw OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counters of linkup and linkdown times of the interface." ::= { fsApIfEntry 35 } fsApIfInPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 36 } fsApIfInFlow OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The flow rate of data octets in units of Bytes per-second received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 37 } fsApIfOutFlow OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The flow rate of data octets in units of Bytes per-second transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 38 } fsApIfInBrdcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of broadcast packets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 39 } fsApIfOutBrdcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of broadcast packets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 40 } fsApIfInMulcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of multicast packets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 41 } fsApIfOutMulcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of multicast packets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 42 } fsApIfInPayloadOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of payload octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 43 } fsApIfOutPayloadOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of payload octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 44 } fsApIfAlias OBJECT-TYPE SYNTAX DisplayString(SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "A textual string containing alias information about the interface." ::= { fsApIfEntry 45 } fsApIfInDateRate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The flow rate of data octets in units of Kilo-Bits per-second received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 46 } fsApIfOutDateRate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The flow rate of data octets in units of Kilo-Bits per-second transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 47 } fsApifInNormalPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of normal packets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 48 } fsApIfOutPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsApIfEntry 49 } fsIfLinkTable OBJECT-TYPE SYNTAX SEQUENCE OF FSIfLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of interface entries. The number of entries is given by the value of ifNumber." ::= { fsIfConfigMIBObjects 14 } fsIfLinkEntry OBJECT-TYPE SYNTAX FSIfLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing management information applicable to a particular interface." INDEX { fsIfLinkIndex } ::= { fsIfLinkTable 1 } FSIfLinkEntry ::= SEQUENCE { fsIfLinkIndex IfIndex, fsIfUplinkInOctets Counter32, fsIfUplinkInUcastPkts Counter32, fsIfUplinkInNUcastPkts Counter32, fsIfUplinkInDiscards Counter32, fsIfUplinkInErrors Counter32, fsIfUplinkOutOctets Counter32, fsIfUplinkOutUcastPkts Counter32, fsIfUplinkOutNUcastPkts Counter32, fsIfUplinkOutDiscards Counter32, fsIfUplinkOutErrors Counter32, fsIfDownlinkInOctets Counter32, fsIfDownlinkInUcastPkts Counter32, fsIfDownlinkInNUcastPkts Counter32, fsIfDownlinkInDiscards Counter32, fsIfDownlinkInErrors Counter32, fsIfDownlinkOutOctets Counter32, fsIfDownlinkOutUcastPkts Counter32, fsIfDownlinkOutNUcastPkts Counter32, fsIfDownlinkOutDiscards Counter32, fsIfDownlinkOutErrors Counter32, fsIfUplinkInBcastPkts Counter64, fsIfUplinkOutBcastPkts Counter64, fsIfDownlinkInBcastPkts Counter64, fsIfDownlinkOutBcastPkts Counter64 } fsIfLinkIndex OBJECT-TYPE SYNTAX IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization." ::= { fsIfLinkEntry 1 } fsIfUplinkInOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 2 } fsIfUplinkInUcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 3 } fsIfUplinkInNUcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime. This object is deprecated in favour of ifInMulticastPkts and ifInBroadcastPkts." ::= { fsIfLinkEntry 4 } fsIfUplinkInDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 5 } fsIfUplinkInErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character- oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 6 } fsIfUplinkOutOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 7 } fsIfUplinkOutUcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 8 } fsIfUplinkOutNUcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime. This object is deprecated in favour of ifOutMulticastPkts and ifOutBroadcastPkts." ::= { fsIfLinkEntry 9 } fsIfUplinkOutDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 10 } fsIfUplinkOutErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 11 } fsIfDownlinkInOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 12 } fsIfDownlinkInUcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 13 } fsIfDownlinkInNUcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime. This object is deprecated in favour of ifInMulticastPkts and ifInBroadcastPkts." ::= { fsIfLinkEntry 14 } fsIfDownlinkInDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 15 } fsIfDownlinkInErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character- oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 16 } fsIfDownlinkOutOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 17 } fsIfDownlinkOutUcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 18 } fsIfDownlinkOutNUcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime. This object is deprecated in favour of ifOutMulticastPkts and ifOutBroadcastPkts." ::= { fsIfLinkEntry 19 } fsIfDownlinkOutDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 20 } fsIfDownlinkOutErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 21 } fsIfUplinkInBcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of upbound and inbound packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 22 } fsIfUplinkOutBcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of upbound and outbound packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 23 } fsIfDownlinkInBcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of downbound and inbound packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 24 } fsIfDownlinkOutBcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of downbound and outbound packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime." ::= { fsIfLinkEntry 25 } -- interface traffic statistics, added by Yin Xiaojie, March 2013 fsIfTrafficStatisticsObjects OBJECT IDENTIFIER ::= { fsIfConfigMIBObjects 15 } fsIfLinkTrafficStatistics OBJECT IDENTIFIER ::= { fsIfTrafficStatisticsObjects 1 } fsIfLinkQosStatistics OBJECT IDENTIFIER ::= { fsIfTrafficStatisticsObjects 2 } fsIfDeviceTrafficStatistics OBJECT IDENTIFIER ::= { fsIfTrafficStatisticsObjects 3 } -- physical interface configuration table fsIfPhyTable OBJECT-TYPE SYNTAX SEQUENCE OF FSIfPhyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "list of physical interface basic configuration objects." ::= { fsIfConfigMIBObjects 16 } fsIfPhyEntry OBJECT-TYPE SYNTAX FSIfPhyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry contains physical interface basic configurations." INDEX { fsIfPhyIndex } ::= { fsIfPhyTable 1 } FSIfPhyEntry ::= SEQUENCE { fsIfPhyIndex IfIndex, fsifPhyOperStatus INTEGER } fsIfPhyIndex OBJECT-TYPE SYNTAX IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Physical port index." ::= { fsIfPhyEntry 1 } fsifPhyOperStatus OBJECT-TYPE SYNTAX INTEGER { up(0), down(1), admindown(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational state of the physical interface." ::= { fsIfPhyEntry 2 } -- interface peak rate information table fsIfPeakRateTable OBJECT-TYPE SYNTAX SEQUENCE OF FSIfPeakRateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "list of interface peak rate information objects." ::= { fsIfConfigMIBObjects 17 } fsIfPeakRateEntry OBJECT-TYPE SYNTAX FSIfPeakRateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry contains interface peak rate information." INDEX { fsIfPeakRateIndex } ::= { fsIfPeakRateTable 1 } FSIfPeakRateEntry ::= SEQUENCE { fsIfPeakRateIndex IfIndex, fsIfRxPeakRate Counter64, fsIfRxPeakRateTime DisplayString, fsIfTxPeakRate Counter64, fsIfTxPeakRateTime DisplayString } fsIfPeakRateIndex OBJECT-TYPE SYNTAX IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "interface index." ::= { fsIfPeakRateEntry 1 } fsIfRxPeakRate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The transmission peak rate of interface." ::= { fsIfPeakRateEntry 2 } fsIfRxPeakRateTime OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The occuring time of transmission peak rate of interface." ::= { fsIfPeakRateEntry 3 } fsIfTxPeakRate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The receiving peak rate of interface." ::= { fsIfPeakRateEntry 4 } fsIfTxPeakRateTime OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The occuring time of receiving peak rate of interface." ::= { fsIfPeakRateEntry 5 } -- AP info table fsApInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF FSApInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "list of ap information objects." ::= { fsIfConfigMIBObjects 18 } fsApInfoEntry OBJECT-TYPE SYNTAX FSApInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry contains ap information." INDEX { fsApInfoAddress } ::= { fsApInfoTable 1 } FSApInfoEntry ::= SEQUENCE { fsApInfoAddress PhysAddress, fsApInfoWireInRate Counter64, fsApInfoWireOutRate Counter64, fsApInfoWireInOctets Counter64, fsApInfoWireOutOctets Counter64 } fsApInfoAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The ap's address at its protocol sub-layer. The ap's media-specific MIB must define the bit and byte ordering and the format of the value of this object. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length." ::= { fsApInfoEntry 1 } fsApInfoWireInRate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The input rate in bps of all ap wire-ports." ::= { fsApInfoEntry 2 } fsApInfoWireOutRate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The output rate in bps of all ap wire-ports." ::= { fsApInfoEntry 3 } fsApInfoWireInOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets received on the ap wire-ports." ::= { fsApInfoEntry 4 } fsApInfoWireOutOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets transmitted out of the ap wire-ports." ::= { fsApInfoEntry 5 } -- units of fsIfDropTable fsIfDropTable OBJECT-TYPE SYNTAX SEQUENCE OF FSIfDropEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of interface drop statistics." ::= { fsIfConfigMIBObjects 19 } fsIfDropEntry OBJECT-TYPE SYNTAX FSIfDropEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Interface statistics drop entry" INDEX { fsIfDropIndex } ::= { fsIfDropTable 1 } FSIfDropEntry ::= SEQUENCE { fsIfDropIndex Unsigned32, fsIfInDropPkts Counter64, fsIfInResLackPkts Counter64, fsIfInQosDropPkts Counter64, fsIfFwdEntryDropPkts Counter64, fsIfOutDropPkts Counter64, fsIfOutResLackPkts Counter64, fsIfNoBufferConut Counter64, fsIfOBMDropPkts Counter64 } fsIfDropIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The device traffic drop interface index." ::= { fsIfDropEntry 1 } fsIfInDropPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Input discarded packets without drop by QOS." ::= { fsIfDropEntry 2 } fsIfInResLackPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Input discarded packets by resources lack." ::= { fsIfDropEntry 3 } fsIfInQosDropPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Discarded packets by QOS." ::= { fsIfDropEntry 4 } fsIfFwdEntryDropPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Input discarded packets by forwardind entry." ::= { fsIfDropEntry 5 } fsIfOutDropPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Output discarded packets." ::= { fsIfDropEntry 6 } fsIfOutResLackPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Output discarded packets by resources lack." ::= { fsIfDropEntry 7 } fsIfNoBufferConut OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "discarded packets by no buffer." ::= { fsIfDropEntry 8 } fsIfOBMDropPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "OBM discarded packets." ::= { fsIfDropEntry 9 } -- units of LinkTrafficStatistics fsIfLinkTrafficTable OBJECT-TYPE SYNTAX SEQUENCE OF FSIfLinkTrafficEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of link traffic statistics, including interface rate and bandwidth utilization." ::= { fsIfLinkTrafficStatistics 1 } fsIfLinkTrafficEntry OBJECT-TYPE SYNTAX FSIfLinkTrafficEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The link traffic statistics entry." INDEX { fsIfLinkTrafficIndex } ::= { fsIfLinkTrafficTable 1 } FSIfLinkTrafficEntry ::= SEQUENCE { fsIfLinkTrafficIndex Unsigned32, fsIfLinkAvgRate Counter32, fsIfLinkPeakRate Counter32, fsIfLinkAvgBWUtilization INTEGER, fsIfLinkPeakBWUtilization INTEGER } fsIfLinkTrafficIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The link traffic interface index." ::= { fsIfLinkTrafficEntry 1 } fsIfLinkAvgRate OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "An estimate of the interface's average bandwidth in units of bits per second." DEFVAL { 0 } ::= { fsIfLinkTrafficEntry 2 } fsIfLinkPeakRate OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "An estimate of the interface's current peak bandwidth in units of bits per second." DEFVAL { 0 } ::= { fsIfLinkTrafficEntry 3 } fsIfLinkAvgBWUtilization OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "An estimate of the interface's average bandwidth Utilization." DEFVAL { 0 } ::= { fsIfLinkTrafficEntry 4 } fsIfLinkPeakBWUtilization OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "An estimate of the interface's current peak bandwidth Utilization." DEFVAL { 0 } ::= { fsIfLinkTrafficEntry 5 } -- units of LinkQosStatistics fsLinkQosCtlTable OBJECT-TYPE SYNTAX SEQUENCE OF FSLinkQosCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The results of these operations are stored in the fsLinkQosResultsTable" ::= { fsIfLinkQosStatistics 1 } fsLinkQosCtlEntry OBJECT-TYPE SYNTAX FSLinkQosCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines an entry in the fsLinkQosCtlTable. The first index element, fsLinkQosCtlOwnerIndex, is of type SnmpAdminString, a textual convention that allows for use of the SNMPv3 View-Based Access Control Model (RFC 3415, VACM) and that allows a management application to identify its entries. The second index, fsLinkQosCtlTestName (also an SnmpAdminString), enables the same management application to have multiple outstanding requests." INDEX { fsLinkQosCtlOwnerIndex, fsLinkQosCtlTestName } ::= { fsLinkQosCtlTable 1 } FSLinkQosCtlEntry ::= SEQUENCE { fsLinkQosCtlOwnerIndex SnmpAdminString, fsLinkQosCtlTestName SnmpAdminString, fsLinkQosCtlTargetAddressType InetAddressType, fsLinkQosCtlTargetAddress InetAddress, fsLinkQosCtlAdminStatus INTEGER, fsLinkQosCtlRowStatus RowStatus } fsLinkQosCtlOwnerIndex OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "To facilitate the provisioning of access control by a security administrator using the View-Based Access Control Model (RFC 2575, VACM) for tables in which multiple users may need to create or modify entries independently, the initial index is used as an 'owner index'. Such an initial index has a syntax of SnmpAdminString and can thus be trivially mapped to a securityName or groupName defined in VACM, in accordance with a security policy." ::= { fsLinkQosCtlEntry 1 } fsLinkQosCtlTestName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of the ping-based test. This is locally unique, within the scope of a fsLinkQosCtlOwnerIndex." ::= { fsLinkQosCtlEntry 2 } fsLinkQosCtlTargetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the type of host address to be used at a remote host for performing a ping-based operation." DEFVAL { unknown } ::= { fsLinkQosCtlEntry 3 } fsLinkQosCtlTargetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the host address to be used at a remote host for performing a ping-based operation. The host address type is determined by the value of the corresponding fsLinkQosCtlTargetAddressType." DEFVAL { ''H } ::= { fsLinkQosCtlEntry 4 } fsLinkQosCtlAdminStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), -- test should be started disabled(2) -- test should be stopped } MAX-ACCESS read-create STATUS current DESCRIPTION "Reflects the desired state that a fsLinkQosCtlEntry should be in: enabled(1) - Attempt to activate the test as defined by this fsLinkQosCtlEntry. disabled(2) - Deactivate the test as defined by this fsLinkQosCtlEntry. Refer to the corresponding fsLinkQosResultsOperStatus to determine the operational state of the test defined by this entry." DEFVAL { disabled } ::= { fsLinkQosCtlEntry 5 } fsLinkQosCtlRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table." REFERENCE "See definition of RowStatus in RFC 2579, 'Textual Conventions for SMIv2.'" ::= { fsLinkQosCtlEntry 6 } -- Results Table fsLinkQosResultsTable OBJECT-TYPE SYNTAX SEQUENCE OF FSLinkQosResultsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The results of these operations are stored in the fsLinkQosResultsTable." ::= { fsIfLinkQosStatistics 2 } fsLinkQosResultsEntry OBJECT-TYPE SYNTAX FSLinkQosResultsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines an entry in the fsLinkQosResultsTable. The fsLinkQosResultsTable has the same indexing as the fsLinkQosCtlTable so that a fsLinkQosResultsEntry corresponds to the fsLinkQosCtlEntry that caused it to be created." INDEX { fsLinkQosCtlOwnerIndex, fsLinkQosCtlTestName } ::= { fsLinkQosResultsTable 1 } FSLinkQosResultsEntry ::= SEQUENCE { fsLinkQosResultsOperStatus INTEGER, fsLinkQosResultsIpTargetAddressType InetAddressType, fsLinkQosResultsIpTargetAddress InetAddress, fsLinkQosResultsMaxRtt Unsigned32, fsLinkQosResultsMinRtt Unsigned32, fsLinkQosResultsAverageRtt Unsigned32, fsLinkQosResultsDelayJitter Unsigned32, fsLinkQosResultsPktsLossRate Unsigned32, fsLinkQosResultsNetworkAF Unsigned32 } fsLinkQosResultsOperStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), -- test is in progress disabled(2), -- test has stopped completed(3) -- test is completed } MAX-ACCESS read-only STATUS current DESCRIPTION "Reflects the operational state of a fsLinkQosCtlEntry: enabled(1) - Test is active. disabled(2) - Test has stopped. completed(3) - Test is completed." ::= { fsLinkQosResultsEntry 1 } fsLinkQosResultsIpTargetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the type of address stored in the corresponding fsLinkQosResultsIpTargetAddress object." DEFVAL { unknown } ::= { fsLinkQosResultsEntry 2 } fsLinkQosResultsIpTargetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object reports the IP address associated with a fsLinkQosCtlTargetAddress value when the destination address is specified as a DNS name. The value of this object should be a zero-length octet string when a DNS name is not specified or when a specified DNS name fails to resolve. The address type (InetAddressType) that relates to this object is specified by the corresponding value of fsLinkQosResultsIpTargetAddressType." DEFVAL { ''H } ::= { fsLinkQosResultsEntry 3 } fsLinkQosResultsMaxRtt OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum packet round-trip-time (RTT) that received. A value of 0 for this object implies that no RTT has been received." ::= { fsLinkQosResultsEntry 4 } fsLinkQosResultsMinRtt OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum packet round-trip-time (RTT) that received. A value of 0 for this object implies that no RTT has been received." ::= { fsLinkQosResultsEntry 5 } fsLinkQosResultsAverageRtt OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The current average packet round-trip-time (RTT)." ::= { fsLinkQosResultsEntry 6 } fsLinkQosResultsDelayJitter OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the sum of the squares for all ping responses received. Its purpose is to enable standard deviation calculation. The estimate value of the delay jitter." ::= { fsLinkQosResultsEntry 7 } fsLinkQosResultsPktsLossRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The packets loss rate of the link." ::= { fsLinkQosResultsEntry 8 } fsLinkQosResultsNetworkAF OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The network availability factor." ::= { fsLinkQosResultsEntry 9 } -- units of DeviceTrafficStatistics fsIfDeviceTrafficTable OBJECT-TYPE SYNTAX SEQUENCE OF FSIfDeviceTrafficEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of device traffic statistics." ::= { fsIfDeviceTrafficStatistics 1 } fsIfDeviceTrafficEntry OBJECT-TYPE SYNTAX FSIfDeviceTrafficEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Device traffic statistics entry" INDEX { fsIfDeviceTrafficIndex } ::= { fsIfDeviceTrafficTable 1 } FSIfDeviceTrafficEntry ::= SEQUENCE { fsIfDeviceTrafficIndex Unsigned32, fsIfFC INTEGER, fsIfFCTransRate Counter32, fsIfFCTransPktsNum Counter64, fsIfFCDiscardRate Counter32, fsIfFCDiscardPktsNum Counter64, fsIfFCPktsLossRate INTEGER, fsIfFCBandwidthRate Counter32, fsIfFCBandwidthPercentage INTEGER, fsIfDeviceFCGathers INTEGER, fsIfFullMeshFCGathers INTEGER, fsIfClassBasedGathers INTEGER, fsIfNodeBasedGathers INTEGER, fsIfNodeClassBasedGathers INTEGER, fsIfNodeFCBasedGathers INTEGER, fsIfNodeDeviceFCBasedGathers INTEGER } fsIfDeviceTrafficIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The device traffic interface index." ::= { fsIfDeviceTrafficEntry 1 } fsIfFC OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The FC type. 2--BASE_X_10 4--BASE_X_100 6--BASE_X_1000 8--BASE_X_10000 9--BASE_ERROR" ::= { fsIfDeviceTrafficEntry 2 } fsIfFCTransRate OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The transmission rate of the FC." ::= { fsIfDeviceTrafficEntry 3 } fsIfFCTransPktsNum OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The transmission packets number of the FC." ::= { fsIfDeviceTrafficEntry 4 } fsIfFCDiscardRate OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The discard rate of the FC." ::= { fsIfDeviceTrafficEntry 5 } fsIfFCDiscardPktsNum OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The discard packets number of the FC." ::= { fsIfDeviceTrafficEntry 6 } fsIfFCPktsLossRate OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The packets loss rate of the FC." ::= { fsIfDeviceTrafficEntry 7 } fsIfFCBandwidthRate OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The bandwidth rate of the FC." ::= { fsIfDeviceTrafficEntry 8 } fsIfFCBandwidthPercentage OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The bandwidth percentage of the FC." ::= { fsIfDeviceTrafficEntry 9 } fsIfDeviceFCGathers OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Gathers of the device FC." ::= { fsIfDeviceTrafficEntry 10 } fsIfFullMeshFCGathers OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Gathers of the whole network FC." ::= { fsIfDeviceTrafficEntry 11 } fsIfClassBasedGathers OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Class-based Gathers." ::= { fsIfDeviceTrafficEntry 12 } fsIfNodeBasedGathers OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Node-based Gathers." ::= { fsIfDeviceTrafficEntry 13 } fsIfNodeClassBasedGathers OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Node&class-based Gathers." ::= { fsIfDeviceTrafficEntry 14 } fsIfNodeFCBasedGathers OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Node&FC-based Gathers." ::= { fsIfDeviceTrafficEntry 15 } fsIfNodeDeviceFCBasedGathers OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Node&device&FC-based Gathers." ::= { fsIfDeviceTrafficEntry 16 } -- Notification fsInterfaceTraps OBJECT IDENTIFIER ::= { fsInterfaceMIB 2 } lineDetectStatus OBJECT-TYPE SYNTAX INTEGER{ ok(1), --line has restored to normal state open(2), --a break in the line short(3) --short circuit in the line } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The type of storm of interface" ::= { fsInterfaceTraps 1 } lineDetectPosition OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Location where the break or short circuit in the line happens (Distance from the switch port, in metre.)" ::= { fsInterfaceTraps 2 } lineQualityDetect NOTIFICATION-TYPE OBJECTS {ifIndex, lineDetectStatus,lineDetectPosition} STATUS current DESCRIPTION "The notification of discovering a break or short circuit in the line, or restoring the line to the normal state." ::= { fsInterfaceTraps 3 } fsInterfaceMIBConformance OBJECT IDENTIFIER ::= { fsInterfaceMIB 3 } fsInterfaceMIBCompliances OBJECT IDENTIFIER ::= { fsInterfaceMIBConformance 1 } fsInterfaceMIBGroups OBJECT IDENTIFIER ::= { fsInterfaceMIBConformance 2 } -- compliance statements fsInterfaceMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the FS Interface MIB" MODULE -- this module MANDATORY-GROUPS { fsInterfaceMIBGroup } GROUP fsPortTypeChooseMibGroup DESCRIPTION "This group is mandatory when system supports optional port type." GROUP fsIfMTUMibGroup DESCRIPTION "This group is mandatory when system supports MTU setting." GROUP fsIfLineDetectGroup DESCRIPTION "This group is mandatory when system supports line quality detection." GROUP fsIfAvailableBWMibGroup DESCRIPTION "This group is mandatory when system supports available bandwidth getting." ::= { fsInterfaceMIBCompliances 1 } -- units of conformance fsInterfaceMIBGroup OBJECT-GROUP OBJECTS { fsIfIndex, fsIfPortType, fsIfFlowControlAdminStatus, fsIfFlowControlOperStatus, fsIfAdminSpeed, fsIfAdminDuplex, fsIfOperSpeed, fsIfOperDuplex, fsIfManageStatus, fsIfIpBroadcast, fsIfLayer, fsIfMode, fsIfCounterClear, fsIfEntryStatus, fsIfMediumType, fsIfDownCounter, fsIfInOctets, fsIfOutOctets, fsIfBcastInhibit, fsIfNegotiation, fsIfPhysAddress, fsIfAdminSpeedRW, fsIfAdminDuplexRW, fsIfModeRW, fsIfSpeed, fsifAdminStatus, fsifOperStatus, fsIfInNUcastPkts, fsIfOutNUcastPkts, fsIfUpDownTimes, fsifAdminStatusw, fsifOperStatusw, fsifSpeedw, fsifMacAddress, fsifLastChange, fsIfInPkts, fsIfDiscard, fsIfBandwidthUsage, fsIfInBitsRate, fsIfInPktRate, fsIfOutBitsRate, fsIfOutPktRate, fsIfInBandwidthUsage, fsIfOutBandwidthUsage, fsIfInErrorPktsRate, fsIfOutErrorPktsRate, fsIfInDropPktsRate, fsIfOutDropPktsRate, fsIfIpIfIndex, fsIfIpId, fsIfIp, fsIfIpMask, fsIfIpEntryStatus, fsIfStatusIndex, fsIfStatusLoopBackExamine, fsIfErrorStatus, fsGlobalIfDisableRecovery, fsIfSVICreatVlanNum, fsIfHandleSVI, fsIfEncapsulationIndex, fsIfEncapsulationVlan, fsApPhyAddress, fsApIfNumber, fsApIfPhyIntNum, fsApPhysAddress, fsApIfIndex, fsApIfDescr, fsApIfType, fsApIfMtu, fsApIfSpeed, fsApIfPhysAddress, fsApIfAdminStatus, fsApIfOperStatus, fsApIfLastChange, fsApIfInOctets, fsApIfInUcastPkts, fsApIfInNUcastPkts, fsApIfInDiscards, fsApIfInErrors, fsApIfInUnknownProtos, fsApIfOutOctets, fsApIfOutUcastPkts, fsApIfOutNUcastPkts, fsApIfOutDiscards, fsApIfOutErrors, fsApIfOutQLen, fsApIfLinkUPTimes, fsApIfInDataOctets, fsApIfOutDataOctets, fsApIfMgmtUploadOctets, fsApIfMgmtDownloadOctets, fsApIfSpeedw, fsApIfMtuw, fsApIfPhysAddressw, fsApIfInUcastPktsw, fsApIfInNUcastPktsw, fsApIfOutUcastPktsw, fsApIfOutNUcastPktsw, fsApIfLinkUPTimesw, fsApIfInPkts, fsApIfInFlow, fsApIfOutFlow, fsApIfInBrdcastPkts, fsApIfOutBrdcastPkts, fsApIfInMulcastPkts, fsApIfOutMulcastPkts, fsApIfInPayloadOctets, fsApIfOutPayloadOctets, fsApIfAlias, fsApIfInDateRate, fsApIfOutDateRate, fsApifInNormalPkts, fsApIfOutPkts, fsIfLinkIndex, fsIfUplinkInOctets, fsIfUplinkInUcastPkts, fsIfUplinkInNUcastPkts, fsIfUplinkInDiscards, fsIfUplinkInErrors, fsIfUplinkOutOctets, fsIfUplinkOutUcastPkts, fsIfUplinkOutNUcastPkts, fsIfUplinkOutDiscards, fsIfUplinkOutErrors, fsIfDownlinkInOctets, fsIfDownlinkInUcastPkts, fsIfDownlinkInNUcastPkts, fsIfDownlinkInDiscards, fsIfDownlinkInErrors, fsIfDownlinkOutOctets, fsIfDownlinkOutUcastPkts, fsIfDownlinkOutNUcastPkts, fsIfDownlinkOutDiscards, fsIfDownlinkOutErrors, fsIfUplinkInBcastPkts, fsIfUplinkOutBcastPkts, fsIfDownlinkInBcastPkts, fsIfDownlinkOutBcastPkts } STATUS current DESCRIPTION "A collection of objects providing interface basic configure ." ::= { fsInterfaceMIBGroups 1 } fsPortTypeChooseMibGroup OBJECT-GROUP OBJECTS { fsPortTypeChooseIndex, fsPortTypeChooseType } STATUS current DESCRIPTION "Information collection of choosing port type." ::= { fsInterfaceMIBGroups 2 } fsIfMTUMibGroup OBJECT-GROUP OBJECTS { fsIfMTUIndex, fsIfMTU } STATUS current DESCRIPTION "Interface MTU information collection." ::= { fsInterfaceMIBGroups 3 } fsIfLineDetectGroup OBJECT-GROUP OBJECTS { fsIfLineDetect } STATUS current DESCRIPTION "Information collection of line quality detection." ::= { fsInterfaceMIBGroups 4 } fsIfAvailableBWMibGroup OBJECT-GROUP OBJECTS { fsIfAvailableBWIfIndex, fsIfAvailableBWIfBW } STATUS current DESCRIPTION "Interface available bandwidth information collection." ::= { fsInterfaceMIBGroups 5 } END