-- ################################################################################ EXTREME-MPLS-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, Counter32, Counter64 FROM SNMPv2-SMI -- [RFC2578] MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- [RFC2580] extremeAgent FROM EXTREME-BASE-MIB TruthValue, TimeStamp FROM SNMPv2-TC -- [RFC2579] SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- [RFC3411 ] PwIndexType, PwOperStatusTC, PwStatus FROM PW-TC-STD-MIB -- [PWTC] VPNIdOrZero FROM VPN-TC-STD-MIB -- [RFC4265] InetAddressType, InetAddress FROM INET-ADDRESS-MIB -- [RFC4001] -- IndexInteger, -- IndexIntegerNextFree -- FROM DIFFSERV-MIB -- [RFC3289] MplsTunnelIndex, MplsTunnelInstanceIndex, MplsExtendedTunnelId, MplsLdpIdentifier, MplsLsrIdentifier FROM MPLS-TC-STD-MIB -- [RFC3811] pwIndex FROM PW-STD-MIB -- [PWMIB] MplsIndexType FROM MPLS-LSR-STD-MIB -- [RFC3813] ; extremeMplsMIB MODULE-IDENTITY LAST-UPDATED "201006280000Z" -- June 28, 2010 ORGANIZATION "Extreme Networks, Inc." CONTACT-INFO "www.extremenetworks.com" DESCRIPTION "Extreme extensions to mplsTeStdMIB" ::= { extremeAgent 37 } -- Notifications extremeMplsNotifications OBJECT IDENTIFIER ::= { extremeMplsMIB 0 } extremeMplsScalars OBJECT IDENTIFIER ::= { extremeMplsMIB 1 } -- DEFINED IN extremersvpmib.my -- extremeMplsTeMIB MODULE-IDENTITY ::= { extremeMplsMIB 2 } extremeVplsObjects OBJECT IDENTIFIER ::= { extremeMplsMIB 3 } extremeL2VpnMplsNotificationHandler OBJECT IDENTIFIER ::= { extremeMplsMIB 4 } extremePwObjects OBJECT IDENTIFIER ::= { extremeMplsMIB 5 } IndexInteger ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "An integer which may be used as a table index." SYNTAX Unsigned32 (1..4294967295) extremePwUpDownNotificationEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this object is set to true(1), then it enables the emission of pwUp and pwDown notifications; otherwise these notifications are not emitted." REFERENCE "See also [RFC3413] for explanation that notifications are under the ultimate control of the MIB module in this document." DEFVAL { true } ::= { extremeMplsScalars 5 } extremePwDeletedNotificationEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this object is set to true(1), then it enables the emission of pwDeleted notification; otherwise this notification is not emitted." REFERENCE "See also [RFC3413] for explanation that notifications are under the ultimate control of the MIB module in this document." DEFVAL { true } ::= { extremeMplsScalars 6 } extremePwNotificationMaxRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This variable indicates the maximum number of notifications issued per second. If events occur more rapidly, the implementation may simply fail to emit these notifications during that period, or may queue them until an appropriate time. A value of 0 means no throttling is applied and events may be notified at the rate at which they occur." DEFVAL { 0 } ::= { extremeMplsScalars 7 } extremePwNotificationPwIndex OBJECT-TYPE SYNTAX PwIndexType MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This variable indicates the index of the pseudowire that either went up, down, or was deleted as reported by the corresponding notification. To obtain further information regarding the pseudowire, the network administrator should look up the corresponding pseudowire entry in pwTable (RFC 5601)." ::= { extremeMplsScalars 8 } extremePwNotificationPwOperStatus OBJECT-TYPE SYNTAX PwOperStatusTC MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This variable is used to report the value of pwOperStatus in pwTable (RFC 5601) associated with the pseudowire that went up or down." ::= { extremeMplsScalars 9 } extremePwNotificationPeerAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Denotes the address type of the peer node." ::= { extremeMplsScalars 10 } extremePwNotificationPeerAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object contains the value of the peer node address." ::= { extremeMplsScalars 11 } extremeMplsNotifTunnelIndex OBJECT-TYPE SYNTAX MplsTunnelIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Uniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs. Contains part of the index of a te tunnel that underwent state change. The same tunnel can also be looked up in the te mib." REFERENCE "1. RSVP-TE: Extensions to RSVP for LSP Tunnels, Awduche et al, RFC 3209 , December 2001 2. Constraint-Based LSP Setup using LDP, Jamoussi (Editor), RFC 3212 , January 2002 3. MPLS Traffic Engineering (TE) Management Information Base (MIB). http://www.faqs.org/rfcs/rfc3812.html." ::= { extremeMplsScalars 12 } extremeMplsNotifTunnelInstance OBJECT-TYPE SYNTAX MplsTunnelInstanceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Uniquely identifies a particular instance of a tunnel between a pair of ingress and egress LSRs." ::= { extremeMplsScalars 13 } extremeMplsNotifTunnelIngressLSRId OBJECT-TYPE SYNTAX MplsExtendedTunnelId MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Identity of the ingress LSR associated with this tunnel instance." ::= { extremeMplsScalars 14 } extremeMplsNotifTunnelEgressLSRId OBJECT-TYPE SYNTAX MplsExtendedTunnelId MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Identity of the egress LSR associated with this tunnel instance." ::= { extremeMplsScalars 15 } extremeMplsNotifTunnelAdminStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Reports the desired operational status of this tunnel." ::= { extremeMplsScalars 16 } extremeMplsNotifTunnelOperStatus OBJECT-TYPE SYNTAX INTEGER { -- ready to pass packets up(1), down(2), -- in some test mode testing(3), -- status cannot be determined unknown(4), dormant(5), -- some component is missing notPresent(6), -- down due to the state of -- lower layer interfaces lowerLayerDown(7) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Reports the actual operational status of this tunnel, which is typically but not limited to, a function of the state of individual segments of this tunnel." ::= { extremeMplsScalars 17 } extremeMplsNotifLdpEntityLdpId OBJECT-TYPE SYNTAX MplsLdpIdentifier MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The LDP identifier. This is the primary index to identify a row in the mplsLdpEntityTable (RFC 3815)." REFERENCE "1. RFC3036: LDP Specification, Section on LDP Identifiers. 2. RFC3815: Definitions of Managed Objects for the Multiprotocol Label Switching (MPLS), Label Distribution Protocol (LDP)." ::= { extremeMplsScalars 18 } extremeMplsNotifLdpEntityIndex OBJECT-TYPE SYNTAX IndexInteger MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This index is used as a secondary index to uniquely identify a row in the mplsLdpEntityTable (RFC 3815). This object is meaningful to some but not all, LDP implementations." ::= { extremeMplsScalars 19 } extremeMplsNotifLdpPeerLdpId OBJECT-TYPE SYNTAX MplsLdpIdentifier MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The LDP identifier of this LDP Peer." REFERENCE "1. RFC3036: LDP Specification, Section on LDP Identifiers. 2. RFC3815: Definitions of Managed Objects for LDP." ::= { extremeMplsScalars 20 } extremeMplsNotifLdpSessionState OBJECT-TYPE SYNTAX INTEGER { nonexistent(1), initialized(2), openrec(3), opensent(4), operational(5) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The current state of the session, all of the states 1 to 5 are based on the state machine for session negotiation behavior." REFERENCE "1. RFC3036: LDP Specification, Section 2.5.4, Initialization State Machine. 2. RFC3815: Definitions of Managed Objects for LDP." ::= { extremeMplsScalars 21 } extremeMplsNotifLdpSessionDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The initial value of this object is the value of sysUpTime when the entry was created in this table. Subsequent notifications report the time when the session between a given Entity and Peer goes away or a new session is established." REFERENCE "1. RFC3036: LDP Specification, Section 2.5.4, Initialization State Machine. 2. RFC3815: Definitions of Managed Objects for LDP." ::= { extremeMplsScalars 22 } extremeVplsNotifConfigIndex OBJECT-TYPE SYNTAX Unsigned32 (1.. 2147483647) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Unique index for the conceptual row identifying a VPLS service in the vplsConfigTable." REFERENCE "vplsGenericDraft01MIB: Generic managed object definitions for Virtual Private LAN Services as in [L2VPN-VPLS-LDP] and [L2VPN-VPLS-BGP] The L2VPN Working Group (email distribution l2vpn@ietf.org, http://www.ietf.org/html.charters/l2vpn-charter.html)" ::= { extremeMplsScalars 23 } extremeVplsNotifConfigVpnId OBJECT-TYPE SYNTAX VPNIdOrZero MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This objects indicates the IEEE 802-1990 VPN ID of the associated VPLS service. This object has the same value as vplsConfigVpnId in the vplsConfigTable for an index value equal to extremeVplsNotifConfigIndex sent in the notification." ::= { extremeMplsScalars 24 } extremeVplsNotifConfigAdminStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), testing(3) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The administrative state of the VPLS service. This object has the same value as vplsConfigAdminStatus in the vplsConfigTable for an index value equal to extremeVplsNotifConfigIndex sent in the notification." ::= { extremeMplsScalars 25 } extremeVplsNotifStatusOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), degraded(2), down(3) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The current operational state of this VPLS Service. A value of up(1) indicates that all pseudo-wires for this vpls are up and the attachment circuit is up. A value of degraded(2) indicates that at least one pseudo-wires for this vpls is up and the attachment circuit is up. A value of down(3) indicates that all pseudo-wires for this vpls are down or the attachment circuit is down." ::= { extremeMplsScalars 26 } extremePwStatusChange NOTIFICATION-TYPE OBJECTS { extremePwNotificationPwIndex, extremePwNotificationPwOperStatus } STATUS current DESCRIPTION "This notification is generated when the pwOperStatus object for a pseudowire transitions from up(1) to down(2) or from down(2) to up(1)." ::= { extremeMplsNotifications 1 } extremePwDeleted NOTIFICATION-TYPE OBJECTS { extremePwNotificationPwIndex, extremePwNotificationPeerAddrType, extremePwNotificationPeerAddr } STATUS current DESCRIPTION "This notification is generated when a PW has been deleted." ::= { extremeMplsNotifications 2 } extremeMplsTunnelStatusChange NOTIFICATION-TYPE OBJECTS { extremeMplsNotifTunnelIndex, extremeMplsNotifTunnelInstance, extremeMplsNotifTunnelIngressLSRId, extremeMplsNotifTunnelEgressLSRId, extremeMplsNotifTunnelAdminStatus, extremeMplsNotifTunnelOperStatus } STATUS current DESCRIPTION "This notification is generated when the mplsTunnelOperStatus object for a te-lsp transitions from up(1) to down(2) or from down(2) to up(1). This new state is indicated by the included value of mplsTunnelOperStatus." ::= { extremeMplsNotifications 3 } extremeMplsLdpSessionStatusChange NOTIFICATION-TYPE OBJECTS { extremeMplsNotifLdpEntityLdpId, extremeMplsNotifLdpEntityIndex, extremeMplsNotifLdpPeerLdpId, extremeMplsNotifLdpSessionState, extremeMplsNotifLdpSessionDiscontinuityTime } STATUS current DESCRIPTION "This notification is generated when the value of 'mplsLdpSessionState' (rfc3815) enters or leaves the 'operational(5)' state." ::= { extremeMplsNotifications 4 } extremeVplsStatusChange NOTIFICATION-TYPE OBJECTS { extremeVplsNotifConfigIndex, extremeVplsNotifConfigVpnId, extremeVplsNotifConfigAdminStatus, extremeVplsNotifStatusOperStatus } STATUS current DESCRIPTION "This notification is generated to inform recepients of the state of the Vpls. When all pseudowires in this Vpls are up or ready and the attachment circuit is up, extremeVplsNotifStatusOperStatus is set to vplsOperStatusUp(1) in the notification. When at least one pseudowire in this Vpls is up or ready and the attachment circuit is up, extremeVplsNotifStatusOperStatus is set to vplsOperStatusDegraded(2) in the notification. When all pseudowires in this Vpls are down or the attachment circuit is down, extremeVplsNotifStatusOperStatus is set to vplsOperStatusDown(3) in the notification. Once a notification has been sent with vplsOperStatusDegraded(2), no further notification will be sent untill extremeVplsNotifStatusOperStatus transitions to vplsOperStatusUp(1) or vplsOperStatusDown(3)." REFERENCE "See also Extreme Networks Concepts Guide for a description of H-VPLS." ::= { extremeMplsNotifications 5 } -- VPLS Config table extremeVplsConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeVplsConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies information for configuring and monitoring Virtual Private Lan Services(VPLS). " REFERENCE "VPLS-GENERIC-DRAFT-01-MIB : Generic information for configuring and monitoring Virtual Private Lan Services (VPLS) " ::= { extremeVplsObjects 1 } extremeVplsConfigEntry OBJECT-TYPE SYNTAX ExtremeVplsConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table represents a Virtual Private Lan Service(VPLS) in a packet network. It is indexed by extremeVplsConfigIndex, which uniquely identifies a single VPLS. " INDEX { extremeVplsConfigIndex } ::= { extremeVplsConfigTable 1 } ExtremeVplsConfigEntry ::= SEQUENCE { extremeVplsConfigIndex Unsigned32, extremeVplsConfigRedunType INTEGER, extremeVplsConfigEAPSStatus SnmpAdminString, extremeVplsConfigESRPState SnmpAdminString } extremeVplsConfigIndex OBJECT-TYPE SYNTAX Unsigned32 (1.. 2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Unique index for the conceptual row identifying a VPLS service." ::= { extremeVplsConfigEntry 1 } extremeVplsConfigRedunType OBJECT-TYPE SYNTAX INTEGER { none (0), esrp (1), eaps (2), stp (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the redundancy type for this vpls. Redundacy states can be None, EAPS, ESRP and STP." DEFVAL { none } ::= { extremeVplsConfigEntry 2 } extremeVplsConfigEAPSStatus OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the EAPS redundancy status for this vpls. It displays Protected if the VLAN is protected, else Not Protected. EAPS Status displays the following values Waiting - if we are waiting on EAPS status Connected - if EAPS ring status is connected to VLAN. PW will not be installed in this state. Disconnected - if EAPS ring state is disconnected. PW will be installed in this state. Unknown - if EAPS is not found " ::= { extremeVplsConfigEntry 3 } extremeVplsConfigESRPState OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the ESRP redundancy state for this vpls. ESRP states can have two values : Master and Slave PW will only be installed when ESRP is in the Master state. " ::= { extremeVplsConfigEntry 4 } -- End of Vpls Config table -- VPLS Status table extremeVplsStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeVplsStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies information for configuring and monitoring Virtual Private Lan Services(VPLS). " REFERENCE "VPLS-GENERIC-DRAFT-01-MIB : Generic information for configuring and monitoring Virtual Private Lan Services (VPLS) " ::= { extremeVplsObjects 2 } extremeVplsStatusEntry OBJECT-TYPE SYNTAX ExtremeVplsStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table represents a Virtual Private Lan Service(VPLS) in a packet network. It is indexed by extremeVplsConfigIndex, which uniquely identifies a single VPLS. " INDEX { extremeVplsStatusIndex } ::= { extremeVplsStatusTable 1 } ExtremeVplsStatusEntry ::= SEQUENCE { extremeVplsStatusIndex Unsigned32, extremeVplsOperStatus INTEGER } extremeVplsStatusIndex OBJECT-TYPE SYNTAX Unsigned32 (1.. 2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Unique index for the conceptual row identifying a VPLS service." ::= { extremeVplsStatusEntry 1 } extremeVplsOperStatus OBJECT-TYPE SYNTAX INTEGER { up (1), degraded (2), down (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the vpls operation Status. This is a special status provided which has values up,down and degraded. This is different from the vpls pw status shown in the standard mib. Up - all PWs are in the Up or Ready state. Degraded - Atleast one PW is in the Up or Ready state. Down - None of the PWs are in Up or Ready state." ::= { extremeVplsStatusEntry 2 } -- End of table -- VPLS Peer table extremeVplsPeerTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeVplsPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides information for monitoring Virtual Private Lan Services(VPLS) Peer Entries." REFERENCE "PW-STD-MIB : Information for configuring and monitoring Virtual Private Lan Services (VPLS) Peer Entries" ::= { extremeVplsObjects 3 } extremeVplsPeerEntry OBJECT-TYPE SYNTAX ExtremeVplsPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains information of all the peers belonging to a particular VPLS " INDEX { extremeVplsIndex, extremeVplsPwBindIndex } ::= { extremeVplsPeerTable 1 } ExtremeVplsPeerEntry ::= SEQUENCE { extremeVplsIndex Unsigned32, extremeVplsPwBindIndex PwIndexType, extremePwInstalled TruthValue, extremePwMode INTEGER, extremePwConfiguredRole INTEGER } extremeVplsIndex OBJECT-TYPE SYNTAX Unsigned32 (1.. 2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Unique index for the conceptual row identifying a VPLS service." ::= { extremeVplsPeerEntry 1 } extremeVplsPwBindIndex OBJECT-TYPE SYNTAX PwIndexType MAX-ACCESS not-accessible STATUS current DESCRIPTION "Secondary Index for the conceptual row identifying a pseudowire within the PwEntry which MUST match an entry from the PW-STD-MIB's PwTable which represents an already-provisioned pseuwowire that is then associated with this VPLS instance." ::= { extremeVplsPeerEntry 2 } extremePwInstalled OBJECT-TYPE SYNTAX INTEGER { false (0), true (1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Boolean true or false indicating if PW is installed" ::= { extremeVplsPeerEntry 3 } extremePwMode OBJECT-TYPE SYNTAX INTEGER { coretocore (1), coretospoke (2), spoketocore (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The peer mode of this pw. It indicates its current mode and the mode of the switch it is connected to. It can have the following values : Core-to-core, Core-to-Spoke and Spoke-to-Core." ::= { extremeVplsPeerEntry 4 } extremePwConfiguredRole OBJECT-TYPE SYNTAX INTEGER { primary (1), secondary (2), notApplicable (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The configured role of this pw. It applies only in the case the PWMode is Core-to-core. In this case, the configured role can either be Primary or Secondary. For all the other PW modes, the configured role does not apply." DEFVAL { notApplicable } ::= { extremeVplsPeerEntry 5 } -- End of Vpls Peer table -- Enable/Disable L2VPN/MPLS trap extremeMPLSTrapsEnable OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Mpls Trap status. If enabled then all the mpls related traps will be sent out." ::= { extremeL2VpnMplsNotificationHandler 1 } extremeL2VpnTrapsEnable OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "L2Vpn Trap status. If enabled then all the l2vpn related traps will be sent out." ::= { extremeL2VpnMplsNotificationHandler 2 } -- Extreme PW performance table extremePwPerfTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremePwPerfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides per-PW performance information." ::= { extremePwObjects 1 } extremePwPerfEntry OBJECT-TYPE SYNTAX ExtremePwPerfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for every PW." INDEX { pwIndex } ::= { extremePwPerfTable 1 } ExtremePwPerfEntry ::= SEQUENCE { pwPerfInPackets Counter32, pwPerfInBytes Counter32, pwPerfOutPackets Counter32, pwPerfOutBytes Counter32, pwPerfInHCPackets Counter64, pwPerfInHCBytes Counter64, pwPerfOutHCPackets Counter64, pwPerfOutHCBytes Counter64 } pwPerfInPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter for the total number of packets received by the PW (from the PSN). This is the 32-bit value of the least significant part of the 64-bit value pwPerfInHCPackets." ::= { extremePwPerfEntry 1 } pwPerfInBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter for the total number of bytes received by the PW (from the PSN). This is the 32-bit value of the least significant part of the 64-bit value pwPerfInHCBytes." ::= { extremePwPerfEntry 2 } pwPerfOutPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter for the total number of packets forwarded by the PW (to the PSN). This is the 32-bit value of the least significant part of the 64-bit value pwPerfOutHCPackets." ::= { extremePwPerfEntry 3 } pwPerfOutBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter for the total number of bytes forwarded by the PW (to the PSN). This is the 32-bit value of the least significant part of the 64-bit value pwPerfOutHCBytes." ::= { extremePwPerfEntry 4 } pwPerfInHCPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "High-capacity counter for the total number of packets received by the PW (from the PSN)." ::= { extremePwPerfEntry 5 } pwPerfInHCBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "High-capacity counter for the total number of bytes received by the PW (from the PSN)." ::= { extremePwPerfEntry 6 } pwPerfOutHCPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "High-capacity counter for the total number of packets forwarded by the PW (to the PSN)." ::= { extremePwPerfEntry 7 } pwPerfOutHCBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "High-capacity counter for the total number of bytes forwarded by the PW (to the PSN)." ::= { extremePwPerfEntry 8 } -- end of Extreme PW performance table -- Extreme PW LSP Mapping table extremePwLspOutboundMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremePwLspOutboundMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides mappings between PW and LSP outbound tunnels." ::= { extremePwObjects 2 } extremePwLspOutboundMappingEntry OBJECT-TYPE SYNTAX ExtremePwLspOutboundMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for each LSP in-use by a PW." INDEX { pwIndex, lspIndex } ::= { extremePwLspOutboundMappingTable 1 } ExtremePwLspOutboundMappingEntry ::= SEQUENCE { lspIndex Unsigned32, pwLspOutboundLsrXcIndex MplsIndexType, pwLspOutboundTunnelIndex MplsTunnelIndex, pwLspOutboundTunnelInstance MplsTunnelInstanceIndex, pwLspOutboundTunnelLclLSR MplsLsrIdentifier, pwLspOutboundTunnelPeerLSR MplsLsrIdentifier, pwLspOutboundTunnelTypeInUse INTEGER } lspIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The second index for the table. It contains the unique id assigned to a tunnel used by the PW." ::= { extremePwLspOutboundMappingEntry 1 } pwLspOutboundLsrXcIndex OBJECT-TYPE SYNTAX MplsIndexType MAX-ACCESS read-only STATUS current DESCRIPTION "This object is applicable if pwLspOutboundTunnelTypeInUse is mplsNonTe(2), and MUST return a value of zero otherwise. If the outer tunnel is signaled, it indicates the XC index in the MPLS-LSR-STD-MIB of the outer tunnel toward the peer. Otherwise if tunnel is set up manually, it indicates the XC index of the manually created outer tunnel." ::= { extremePwLspOutboundMappingEntry 2 } pwLspOutboundTunnelIndex OBJECT-TYPE SYNTAX MplsTunnelIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This object is applicable if pwLspOutboundTunnelTypeInUse is mplsTe(1), and MUST return a value of zero otherwise." ::= { extremePwLspOutboundMappingEntry 3 } pwLspOutboundTunnelInstance OBJECT-TYPE SYNTAX MplsTunnelInstanceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This object is applicable if pwLspOutboundTunnelTypeInUse is mplsTe(1), and MUST return a value of zero otherwise." ::= { extremePwLspOutboundMappingEntry 4 } pwLspOutboundTunnelLclLSR OBJECT-TYPE SYNTAX MplsLsrIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "This object is applicable if pwLspOutboundTunnelTypeInUse is mplsTe(1), and MUST return a value of all zeros otherwise." ::= { extremePwLspOutboundMappingEntry 5 } pwLspOutboundTunnelPeerLSR OBJECT-TYPE SYNTAX MplsLsrIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "This object is applicable if pwLspOutboundTunnelTypeInUse is mplsTe(1), and MUST return a value of zero otherwise." ::= { extremePwLspOutboundMappingEntry 6 } pwLspOutboundTunnelTypeInUse OBJECT-TYPE SYNTAX INTEGER { mplsTe (1), mplsNonTe (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current tunnel that is carrying the PW traffic." ::= { extremePwLspOutboundMappingEntry 7 } -- end of Extreme PW LSP Mapping table -- Extreme PW LSP performance table extremePwLspPerfTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremePwLspPerfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides performance information for each LSP in-use by a PW." ::= { extremePwObjects 3 } extremePwLspPerfEntry OBJECT-TYPE SYNTAX ExtremePwLspPerfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for each LSP in-use by a PW." INDEX { pwIndex, lspIndex } ::= { extremePwLspPerfTable 1 } ExtremePwLspPerfEntry ::= SEQUENCE { pwLspPerfOutPackets Counter32, pwLspPerfOutBytes Counter32, pwLspPerfOutHCPackets Counter64, pwLspPerfOutHCBytes Counter64 } pwLspPerfOutPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter for the number of packets forwarded by the LSP for the given PW (to the PSN). This is the 32-bit value of the least significant part of the 64-bit value pwLspPerfOutHCPackets." ::= { extremePwLspPerfEntry 1 } pwLspPerfOutBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter for the number of bytes forwarded by the LSP for the given PW (to the PSN). This is the 32-bit value of the least significant part of the 64-bit value pwLspPerfOutHCBytes." ::= { extremePwLspPerfEntry 2 } pwLspPerfOutHCPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "High-capacity counter for the number of packets forwarded by the LSP for the given PW (to the PSN)." ::= { extremePwLspPerfEntry 3 } pwLspPerfOutHCBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "High-capacity counter for the number of bytes forwarded by the LSP for the given PW (to the PSN)." ::= { extremePwLspPerfEntry 4 } -- end of Extreme PW LSP performance table extremePwNotificationLspIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This variable indicates the index of the LSP that was added to or deleted from a given PW as reported by the corresponding notification." ::= { extremeMplsScalars 27 } extremePwLspAdded NOTIFICATION-TYPE OBJECTS { extremePwNotificationPwIndex, extremePwNotificationLspIndex } STATUS current DESCRIPTION "This notification is generated when an entry is added to the extremePwLspOutboundMappingTable table and the extremePwLspPerfTable table." ::= { extremeMplsNotifications 6 } extremePwLspDeleted NOTIFICATION-TYPE OBJECTS { extremePwNotificationPwIndex, extremePwNotificationLspIndex } STATUS current DESCRIPTION "This notification is generated when an entry is deleted from the extremePwLspOutboundMappingTable table and the extremePwLspPerfTable table." ::= { extremeMplsNotifications 7 } END