-- ******************************************************************* -- CISCO-LWAPP-RRM-MIB.my -- February 2007, Devesh Pujari, Srinath Candadai -- -- Copyright (c) 2007, 2014-2020 by Cisco Systems, Inc. -- All rights reserved. -- ******************************************************************* CISCO-LWAPP-RRM-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, IpAddress, Integer32, NOTIFICATION-TYPE FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF SnmpAdminString FROM SNMP-FRAMEWORK-MIB TEXTUAL-CONVENTION, MacAddress, TimeStamp, TruthValue, RowStatus FROM SNMPv2-TC InetAddressType, InetAddress FROM INET-ADDRESS-MIB cldcClientMacAddress, cldcApMacAddress, cldcIfType FROM CISCO-LWAPP-DOT11-CLIENT-MIB cLApName FROM CISCO-LWAPP-AP-MIB cLWlanChdEnable FROM CISCO-LWAPP-WLAN-MIB CLApIfType FROM CISCO-LWAPP-TC-MIB ciscoMgmt FROM CISCO-SMI; -- ******************************************************************** -- * MODULE IDENTITY -- ******************************************************************** ciscoLwappRrmMIB MODULE-IDENTITY LAST-UPDATED "202010120000Z" ORGANIZATION "Cisco Systems Inc." CONTACT-INFO "Cisco Systems, Customer Service Postal: 170 West Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS Email: cs-wnbu-snmp@cisco.com" DESCRIPTION "This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. Information provided by this MIB is used to study the RRM on the WLAN. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ + + + + + + + CC + + CC + + CC + + + + + + + +......+ +......+ +......+ .. . . .. . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + AP + + AP + + AP + + AP + + + + + + + + + +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + MN + + MN + + MN + + MN + + + + + + + + + +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity is also referred to as 'controller'. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node and client are used interchangeably. Radio Resource Management ( RRM ) RRM is the system level control of co-channel interference and other radio transmission characteristics in wireless communication systems. Received Signal Strength Indicator ( RSSI ) A measure of the strength of the signal as observed by the entity that received it, expressed in 'dbm'. Coverage Hole Detection ( CHD ) If clients on an Access Point are detected at low RSSI levels, it is considered a coverage hole by the Access Points. This indicates the existence of an area where clients are continually getting poor signal coverage, without having a viable location to roam to. Dynamic Channel Assignment (DCA) Dynamic channel assignment (DCA) is used by the controller to minimize adjacent channel interference between access points. BSS Color Optimization (BCO) BCO is used by the controller to minimize BSS color collisions between access points. Dynamic Frequency Selection (DFS) Dynamic frequency selection (DFS) is used by the controller to detect radar signals and avoid interfering with them. RRM RF Grouping Radio Resource Management (RRM) allows the Cisco WLAN controllers to continuously analyze the existing RF environments, and automatically adjust the AP power and channel configurations in order to help alleviate overlapping channel interference, signal coverage problems, and so forth. An RF group is a cluster of Cisco wireless controllers that coordinates its RRM calculations on a per 802.11-network basis. An RF group exists for each 802.11 network type. Clustering controllers into RF groups enables the RRM algorithms to scale beyond a single controller. +....+ Auto-leader +....+ Auto-member + + <-------------> + C2 + + + (802.11a network) +....+ + C1 + + + + + Static-member +....+ Static-leader + + <-------------> + C3 + +....+ (802.11b network) +....+ With the help of above diagram, different aspects of RRM RF Grouping can be explained. Grouping can be configured for 3 modes. 1) Automatic 2) Static 3) Off If the mode is 'Automatic', the controllers automatically form groups and elect leaders to perform better dynamic parameter optimization. If the mode is 'Static', user can select one controller as the group leader and configure the group members manually. If the mode is 'Off', no dynamic grouping occurs. Each controller optimizes only its own APs' parameters. In the above diagram, controller C1 forms a RF group with controller C2 in 802.11a network. And with controller C3, it forms a different group in 802.11b network. For the 802.11a network, the group mode is selected as 'Automatic'. So between C1 and C2 controllers, one would be selected as group leader and the other controller as member automatically by the algorithm. In the above case C1 is the group leader and C2 is the group member. Now for 802.11b network, group mode is selected as 'Static'. Also the user has manually configured C3 as the leader in this group and C1 was added to this group as member. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol" REVISION "202010120000Z" DESCRIPTION "Added few values to clrRrmFraSensitivity" REVISION "202003260000Z" DESCRIPTION "Added clrRrmBcoTable in clrRrmConfig" REVISION "201907300000Z" DESCRIPTION "Changes in clrRrmPakRssiConfig Deprecated the following objects: -clrRrmPakRssiNtp, -clrRrmPakRssiNtpIpAddressType." REVISION "201809250000Z" DESCRIPTION "Added following table - clrRrmRemoveChannelTable - clrRrmAddChannelTable - clrRrmDot11BandJoinedGrpMemberTable Added following new object to clrRrmDcaChannelListTable - clrRrmDcaDefaultChannelList Added notification variable clrRrmSysIdentifier" REVISION "201706090000Z" DESCRIPTION "Added following attributes, - clrRrmFraSensorThreshold - clrRrmFraSensorCoverage - clrRrmFraServicePriority - clrRrmFraSensorDensityOptimisationTargetRssi" REVISION "201703280000Z" DESCRIPTION "Added following new objects to clrRrmParametersTable: - clrRrmParametersTpcVersion - clrRrmParametersChdNoise - clrRrmParametersChdInterference - clrRrmParametersChdLoad - clrRrmParametersChdSignal - clrRrmParametersChdDevice - clrRrmParametersMaxClients - clrRrmParametersRssiCheckEnable - clrRrmParametersRssiThreshold - clrRrmParametersOptRoamEnable - clrRrmParametersOptRoamDataRate - clrRrmParametersOptRoamInterval - clrRrmParametersClientNetworkPreference - clrRrmParametersDcaChannelWidthRev which deprecates clrRrmParametersDcaChannelWidth Added the following OBJECT IDENTIFIER - clrRrmFraConfig - clrRrmPakRssiConfig Added the following objects to clrRrmPakRssiConfig - clrRrmHyperLocationEnable - clrRrmPakRssiThreshold - clrRrmPakRssiThresholdTrigger - clrRrmPakRssiNtpIpAddressType - clrRrmPakRssiNtp Added the following objects to clrRrmFraConfig: - clrRrmFraEnable - clrRrmFraInterval - clrRrmFraSensitivity Added new table clrRrmDcaChannelListTable. Added following Notification Objects: - clrRrmNeighborApCountRev - clrRrmNeighborApMacAddressRev - clrRrmNeighborApRssiRev - clrRrmNeighborApIfTypeRev - clrRrmSysMacAddressRev - clrRrmRssiHistogramValuesRev - clrRrmSysIpAddressType - clrRrmSysIpAddress Added following new OBJECT-GROUP: - ciscoLwappRrmChannelStatusGroup - ciscoLwappRrmParametersGroup - ciscoLwappRrmDCAChannelListGroup - ciscoLwappRrmConfigGroupSup5 - ciscoLwappRrmFraConfigGroup - ciscoLwappRrmConfigGroupSup6 - ciscoLwappRrmChdConfigGroup - ciscoLwappRrmOptRoamGroup - ciscoLwappRrmPakRssiConfigGroup - ciscoLwappRrmNotifyObjectsGroup - ciscoLwappRrmConfigGroupSup7 Added the following NOTIFICATION-GROUP: - ciscoLwappRrmNotifsGroup The following object group is deprecated: - ciscoLwappRrmConfigGroupSup2 Deprecated ciscoLwappRrmMIBComplianceRev2 and replaced by ciscoLwappRrmMIBComplianceRev3." REVISION "201103080000Z" DESCRIPTION "Added following parameters to the table, clrRrmParametersTable. clrRrmParametersDcaChannelWidth, clrRrmParametersMaxTxPower, clrRrmParametersMinTxPower. Deprecated the following object: clrRrmParametersPicoCellMode, clrRrmTupleEntry. Added following scalar variables: clrRrmDcaDot11aOutdoorAPDca, clrRrmRfGroupingPriority. Following two tables have been added for RRM RF Grouping. clrRrmDot11BandGrpTable clrRrmDot11BandGrpMemberTable Following notification related objects have been added: clrRrmApTransmitPowerLevel clrRrmTimeStamp clrRrmClientType clrRrmRssiHistogramLength clrRrmRssiHistogramMaxIndex clrRrmRssiHistogramValues clrRrmNeighborApCount clrRrmNeighborApMacAddress clrRrmNeighborApRssi clrRrmNeighborApIfType clrRrmSysMacAddress clrRrmSysIpAddress Following notifications have been defined: ciscoLwappDot11ClientCoverageHolePreAlarm ciscoLwappRrmRfGroupLeaderChange ciscoLwappRrmRfGroupMemberAdded ciscoLwappRrmRfGroupMemberRemoved." REVISION "200711130000Z" DESCRIPTION "The following objects have been added: 1. clrRrmParametersChdEnable 2. clrRrmParametersVoicePktCountThreshold 3. clrRrmParametersVoicePktPercentThreshold 4. clrRrmParametersVoiceRssiThreshold 5. clrRrmParametersDataPktCountThreshold 6. clrRrmParametersDataPktPercentThreshold 7. clrRrmParametersDataRssiThreshold." REVISION "200702210000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 615 } ciscoLwappRrmMIBNotifs OBJECT IDENTIFIER ::= { ciscoLwappRrmMIB 0 } ciscoLwappRrmMIBObjects OBJECT IDENTIFIER ::= { ciscoLwappRrmMIB 1 } ciscoLwappRrmMIBConform OBJECT IDENTIFIER ::= { ciscoLwappRrmMIB 2 } clrRrmConfig OBJECT IDENTIFIER ::= { ciscoLwappRrmMIBObjects 1 } ClrRrmTupleTuningRange ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "This textual convention defines the RRM tuning parameter range on a 802.11 client." SYNTAX Integer32 (-127..127) -- ******************************************************************** -- * Configuration for parameters -- ******************************************************************** clrRrmParametersTable OBJECT-TYPE SYNTAX SEQUENCE OF ClrRrmParametersEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the RRM parameters for a 802.11 interface type. Entries are automatically created on the controller for each 802.11 interface type." ::= { clrRrmConfig 1 } clrRrmParametersEntry OBJECT-TYPE SYNTAX ClrRrmParametersEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table corresponds to a particular 802.11 interface type." INDEX { clrRrmParametersType } ::= { clrRrmParametersTable 1 } ClrRrmParametersEntry ::= SEQUENCE { clrRrmParametersType CLApIfType, clrRrmParametersPicoCellMode INTEGER, clrRrmParametersChdEnable TruthValue, clrRrmParametersVoicePktCountThreshold Unsigned32, clrRrmParametersVoicePktPercentThreshold Unsigned32, clrRrmParametersVoiceRssiThreshold Integer32, clrRrmParametersDataPktCountThreshold Unsigned32, clrRrmParametersDataPktPercentThreshold Unsigned32, clrRrmParametersDataRssiThreshold Integer32, clrRrmParametersDcaChannelWidth INTEGER, clrRrmParametersMaxTxPower Integer32, clrRrmParametersMinTxPower Integer32, clrRrmParametersTpcVersion INTEGER, clrRrmParametersChdNoise TruthValue, clrRrmParametersChdInterference TruthValue, clrRrmParametersChdLoad TruthValue, clrRrmParametersChdSignal TruthValue, clrRrmParametersChdDevice TruthValue, clrRrmParametersMaxClients Unsigned32, clrRrmParametersRssiCheckEnable TruthValue, clrRrmParametersRssiThreshold Integer32, clrRrmParametersOptRoamEnable TruthValue, clrRrmParametersOptRoamDataRate Integer32, clrRrmParametersOptRoamInterval Integer32, clrRrmParametersClientNetworkPreference INTEGER } clrRrmParametersType OBJECT-TYPE SYNTAX CLApIfType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object uniquely represents the 802.11 interface type for this entry." ::= { clrRrmParametersEntry 1 } clrRrmParametersPicoCellMode OBJECT-TYPE SYNTAX INTEGER { disable(1), picoCellv1(2), picoCellv2(3) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object specifies the 802.11 pico-cell mode. disable - pico-cell mode is disabled. picoCellv1 - legacy pico-cell mode is in use. picoCellv2 - in this mode the APs to use the tuple information from the clrRrmTupleTable. Object is deprecated since controller doesn't support Pico cell configuration anymore." DEFVAL { disable } ::= { clrRrmParametersEntry 2 } clrRrmParametersChdEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the state of CHD (Coverage Hole Detection) on the controller. A value of 'true' indicates that the detection is enabled. A value of 'false' indicates that the detection is disabled." DEFVAL { false } ::= { clrRrmParametersEntry 3 } clrRrmParametersVoicePktCountThreshold OBJECT-TYPE SYNTAX Unsigned32 (1..255) UNITS "packets" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the minimum threshold on the Voice packet count required to trigger the CHD algorithm on the controller." DEFVAL { 10 } ::= { clrRrmParametersEntry 4 } clrRrmParametersVoicePktPercentThreshold OBJECT-TYPE SYNTAX Unsigned32 (1..100) UNITS "percent" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the threshold on the percent of Voice packets dropped, that is required to trigger the CHD algorithm on the controller." DEFVAL { 20 } ::= { clrRrmParametersEntry 5 } clrRrmParametersVoiceRssiThreshold OBJECT-TYPE SYNTAX Integer32 (-90..-60) UNITS "dbm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the RSSI threshold value for Voice packets, that is required to trigger the CHD algorithm on the controller." DEFVAL { -80 } ::= { clrRrmParametersEntry 6 } clrRrmParametersDataPktCountThreshold OBJECT-TYPE SYNTAX Unsigned32 (1..255) UNITS "packets" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the minimum threshold on the Data packet count required to trigger the CHD algorithm on the controller." DEFVAL { 10 } ::= { clrRrmParametersEntry 7 } clrRrmParametersDataPktPercentThreshold OBJECT-TYPE SYNTAX Unsigned32 (1..100) UNITS "percent" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the threshold on the percent of Data packets dropped, that is required to trigger the CHD algorithm on the controller." DEFVAL { 20 } ::= { clrRrmParametersEntry 8 } clrRrmParametersDataRssiThreshold OBJECT-TYPE SYNTAX Integer32 (-90..-60) UNITS "dbm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the RSSI threshold value for Data packets, that is required to trigger the CHD algorithm on the controller." DEFVAL { -74 } ::= { clrRrmParametersEntry 9 } clrRrmParametersDcaChannelWidth OBJECT-TYPE SYNTAX INTEGER { twenty(1), forty(2), eighty(3), best(4), oneSixty(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies how the system performs DCA channel width selection twenty - 20MHz channel width supported by this radio. forty - 40MHz channel width supported by this radio. eighty - 80MHz channel width supported by this radio. oneSixty - 160MHz channel width supported by this radio. best - Dynamic channel width(160MHz, 80MHz, 40MHz or20MHz) supported by this radio." ::= { clrRrmParametersEntry 10 } clrRrmParametersMaxTxPower OBJECT-TYPE SYNTAX Integer32 (-10..30) UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the upper limit of transmit power in dBm. For a 802.11a network, the system will only accept this configuration if the bsnGlobalDot11aDynamicTransmitPowerControl is set to 'automatic' or 'runOnce'. For a 802.11b network, the system will only accept this configuration if the bsnGlobalDot11bDynamicTransmitPowerControl is set to 'automatic' or 'runOnce'. The value of this attribute has to be greater than equal to value of clrRrmParametersMinTxPower." DEFVAL { 30 } ::= { clrRrmParametersEntry 11 } clrRrmParametersMinTxPower OBJECT-TYPE SYNTAX Integer32 (-10..30) UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the lower limit of transmit power in dBm. For an 802.11a network, the system will only accept this configuration if the bsnGlobalDot11aDynamicTransmitPowerControl is set to 'automatic' or 'runOnce'. For an 802.11b network, the system will only accept this configuration if the bsnGlobalDot11bDynamicTransmitPowerControl is set to 'automatic' or 'runOnce'. The value of this attribute has to be less than equal to value of clrRrmParametersMaxTxPower." DEFVAL { -10 } ::= { clrRrmParametersEntry 12 } clrRrmParametersTpcVersion OBJECT-TYPE SYNTAX INTEGER { versionOne(1), versionTwo(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the TPC(Transmission Power Control) version. versionOne(1) - TPC would be in coverage optimal mode. versionTwo(2) - TPC would be in interference optimal mode." ::= { clrRrmParametersEntry 13 } clrRrmParametersChdNoise OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the state of noise on the controller. A value of 'true' indicates that the detection is enabled. A value of 'false' indicates that the detection is disabled." ::= { clrRrmParametersEntry 14 } clrRrmParametersChdInterference OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the state of interference on the controller. A value of 'true' indicates that the detection is enabled. A value of 'false' indicates that the detection is disabled." ::= { clrRrmParametersEntry 15 } clrRrmParametersChdLoad OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the state of load on the controller. A value of 'true' indicates that the detection is enabled. A value of 'false' indicates that the detection is disabled." ::= { clrRrmParametersEntry 16 } clrRrmParametersChdSignal OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the state of signal on the controller. A value of 'true' indicates that the detection is enabled. A value of 'false' indicates that the detection is disabled." ::= { clrRrmParametersEntry 17 } clrRrmParametersChdDevice OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the state of device detection on the controller. A value of 'true' indicates that the detection is enabled. A value of 'false' indicates that the detection is disabled." ::= { clrRrmParametersEntry 18 } clrRrmParametersMaxClients OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the maximum allowed clients per radio." ::= { clrRrmParametersEntry 19 } clrRrmParametersRssiCheckEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the state of RSSI low check on the controller. A value of 'true' indicates that the check is enabled. A value of 'false' indicates that the check is disabled." DEFVAL { false } ::= { clrRrmParametersEntry 20 } clrRrmParametersRssiThreshold OBJECT-TYPE SYNTAX Integer32 (-90..-60) UNITS "dbm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the RSSI threshold value for RSSI low check." DEFVAL { -80 } ::= { clrRrmParametersEntry 21 } clrRrmParametersOptRoamEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the state of optimized roaming feature on the controller. A value of 'true' indicates that the feature is enabled. A value of 'false' indicates that the feature is disabled" DEFVAL { false } ::= { clrRrmParametersEntry 22 } clrRrmParametersOptRoamDataRate OBJECT-TYPE SYNTAX Integer32 (0..54) UNITS "mbps" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the data rate threshold value for optimized roaming. A valid data rate in mbps must be entered." DEFVAL { 0 } ::= { clrRrmParametersEntry 23 } clrRrmParametersOptRoamInterval OBJECT-TYPE SYNTAX Integer32 (5..90) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the reporting interval value for Optimized Roaming." DEFVAL { 90 } ::= { clrRrmParametersEntry 24 } clrRrmParametersClientNetworkPreference OBJECT-TYPE SYNTAX INTEGER { default(1), connectivity(2), throughput(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object represents the client network preference. connectivity - RRM Algorithm has a prefereance on connectiviry of the clients throughput - RRM Algorithm has a preference on high thoughput of the clients default - RRM Algorithm has no preference on the clients" DEFVAL { default } ::= { clrRrmParametersEntry 25 } -- ******************************************************************** -- * Configuration for tuple tuning parameters -- ******************************************************************** clrRrmTupleTable OBJECT-TYPE SYNTAX SEQUENCE OF ClrRrmTupleEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "A list of tuple tuning parameters that are advertised to all APs registered under this 802.11 interface type. This information is pushed down to to 802.11 clients by the APs to operate under high density. Entries in this table are automatically created by the controller with default values. Object is deprecated since controller doesn't support Pico cell configuration anymore." ::= { clrRrmConfig 2 } clrRrmTupleEntry OBJECT-TYPE SYNTAX ClrRrmTupleEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Each entry represents the tuning parameters for an interface type. These entries are applicable only when object clrRrmParametersPicoCellMode is is set to 'picoCellv2'. Pico cell is no more supported so deprecating this attribute. It will be obsolete post 7.0 release. Object is deprecated since controller doesn't support Pico cell configuration anymore." INDEX { clrRrmParametersType } ::= { clrRrmTupleTable 1 } ClrRrmTupleEntry ::= SEQUENCE { clrRrmTupleRxSenseThresholdMin ClrRrmTupleTuningRange, clrRrmTupleRxSenseThresholdMax ClrRrmTupleTuningRange, clrRrmTupleRxSenseThreshold ClrRrmTupleTuningRange, clrRrmTupleCcaSenseThresholdMin ClrRrmTupleTuningRange, clrRrmTupleCcaSenseThresholdMax ClrRrmTupleTuningRange, clrRrmTupleCcaSenseThreshold ClrRrmTupleTuningRange, clrRrmTupleTransmitPowerLevelMin ClrRrmTupleTuningRange, clrRrmTupleTransmitPowerLevelMax ClrRrmTupleTuningRange, clrRrmTupleTransmitPowerLevel ClrRrmTupleTuningRange, clrRrmTupleSetDefault TruthValue } clrRrmTupleRxSenseThresholdMin OBJECT-TYPE SYNTAX ClrRrmTupleTuningRange UNITS "dbm" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object represents the minimum value configured for receiver's sensitivity threshold. This value must be less than the value configured for clrRrmTupleRxSenseThresholdMax object. Object is deprecated since controller doesn't support Pico cell configuration anymore." DEFVAL { -127 } ::= { clrRrmTupleEntry 1 } clrRrmTupleRxSenseThresholdMax OBJECT-TYPE SYNTAX ClrRrmTupleTuningRange UNITS "dbm" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object represents the maximum value configured for receiver's sensitivity threshold. This value must be greater than the value configured for clrRrmTupleRxSenseThresholdMin object. Object is deprecated since controller doesn't support Pico cell configuration anymore." DEFVAL { 127 } ::= { clrRrmTupleEntry 2 } clrRrmTupleRxSenseThreshold OBJECT-TYPE SYNTAX ClrRrmTupleTuningRange UNITS "dbm" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object represents the current value for receiver's sensitivity threshold. This value is sent to the APs that join the controller. The APs in turn propogate this value to the 802.11 clients. The client will either use this value or will tune receiver's sensitivity settings between the range of values configured by clrRrmTupleRxSenseThresholdMin and clrRrmTupleRxSenseThresholdMax objects. Object is deprecated since controller doesn't support Pico cell configuration anymore." DEFVAL { -80 } ::= { clrRrmTupleEntry 3 } clrRrmTupleCcaSenseThresholdMin OBJECT-TYPE SYNTAX ClrRrmTupleTuningRange UNITS "dbm" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object represents the minimum value configured for clear channel (CCA) sensitivity threshold. This value must be less than the value configured for clrRrmTupleCcaSenseThresholdMax object. Object is deprecated since controller doesn't support Pico cell configuration anymore." DEFVAL { -127 } ::= { clrRrmTupleEntry 4 } clrRrmTupleCcaSenseThresholdMax OBJECT-TYPE SYNTAX ClrRrmTupleTuningRange UNITS "dbm" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object represents the maximum value configured for clear channel (CCA) sensitivity threshold. This value must be greater than the value configured for clrRrmTupleCcaSenseThresholdMin object. Object is deprecated since controller doesn't support Pico cell configuration anymore." DEFVAL { 127 } ::= { clrRrmTupleEntry 5 } clrRrmTupleCcaSenseThreshold OBJECT-TYPE SYNTAX ClrRrmTupleTuningRange UNITS "dbm" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object represents the current value for clear channel (CCA) sensitivity. This value is sent to the APs that join the controller. The APs in turn propogate this value to the 802.11 clients. The client will either use this value or may tune CCA sensitivity settings between the range of values configured by clrRrmTupleCcaSenseThresholdMin and clrRrmTupleCcaSenseThresholdMax objects. Object is deprecated since controller doesn't support Pico cell configuration anymore." DEFVAL { -60 } ::= { clrRrmTupleEntry 6 } clrRrmTupleTransmitPowerLevelMin OBJECT-TYPE SYNTAX ClrRrmTupleTuningRange UNITS "dbm" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object represents the minimum value configured for transmit power level. This value must be less than the value configured for clrRrmTupleTransmitPowerLevelMax object. Object is deprecated since controller doesn't support Pico cell configuration anymore." DEFVAL { -127 } ::= { clrRrmTupleEntry 7 } clrRrmTupleTransmitPowerLevelMax OBJECT-TYPE SYNTAX ClrRrmTupleTuningRange UNITS "dbm" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object represents the maximum value configured for transmit power level. This value must be greater than the value for clrRrmTupleTransmitPowerLevelMin object. Object is deprecated since controller doesn't support Pico cell configuration anymore." DEFVAL { 127 } ::= { clrRrmTupleEntry 8 } clrRrmTupleTransmitPowerLevel OBJECT-TYPE SYNTAX ClrRrmTupleTuningRange UNITS "dbm" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object represents the current value for transmit power level. This value is sent to the APs that join the controller. The APs in turn propogate this value to the 802.11 clients. The client will either use this value or may tune the transmit power settings between the range of values configured by clrRrmTupleTransmitPowerLevelMin and clrRrmTupleTransmitPowerLevelMax objects. Object is deprecated since controller doesn't support Pico cell configuration anymore." DEFVAL { 10 } ::= { clrRrmTupleEntry 9 } clrRrmTupleSetDefault OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object restores the other objects in this table to default value. Setting this value to 'true' wil restore defaults as indicated by the DEFVAL clause. This object can only be set to 'true' and all other values are rejected. This object will always return 'false' for get operations. Object is deprecated since controller doesn't support Pico cell configuration anymore." ::= { clrRrmTupleEntry 10 } -- ******************************************************************** -- * Configuration for DCA parameters -- ******************************************************************** clrRrmChannelTable OBJECT-TYPE SYNTAX SEQUENCE OF ClrRrmChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the channel information for an AP's 802.11 interface. Based on the country that an AP operates in, it gets assigned to a regulatory domain. For a given regulatory domain a fixed number of channels are assigned automatically to an AP for a given interface. This table represents this information. Entries are automatically created on the controller as APs associate. Entries are removed when the APs disassociate." ::= { clrRrmConfig 4 } clrRrmChannelEntry OBJECT-TYPE SYNTAX ClrRrmChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table provides the channel information for an 802.11 interface in an AP." INDEX { clrRrmParametersType, clrRrmChannelNum } ::= { clrRrmChannelTable 1 } ClrRrmChannelEntry ::= SEQUENCE { clrRrmChannelNum Unsigned32, clrRrmChannelDcaState TruthValue, clrRrmChannelRowStatus RowStatus } clrRrmChannelNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The channel nubmer for this entry. This value represents the unique channel number on this 802.11 interface for this regulatory domain." ::= { clrRrmChannelEntry 1 } clrRrmChannelDcaState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates whether this channel is part of the dynamic channel allocation (DCA) list. A value of 'true' indicates that the DCA for this channel is enabled. A value of 'false' indicates that the DCA for this channel is disabled." DEFVAL { false } ::= { clrRrmChannelEntry 2 } clrRrmChannelRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row.clrRrmChannelNum and clrRrmChannelDcaState are mandatory for create and go of rowstatus.All writable objects in this row may be modified at any time." ::= { clrRrmChannelEntry 3 } -- ******************************************************************** -- * RRM RF grouping -- ******************************************************************** clrRrmDot11BandGrpTable OBJECT-TYPE SYNTAX SEQUENCE OF ClrRrmDot11BandGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the information about the RRM grouping corresponding to the dot11 band of the APs that have joined the controller. This table has a one-to-one dependent relationship on the clrRrmParametersTable." ::= { clrRrmConfig 5 } clrRrmDot11BandGrpEntry OBJECT-TYPE SYNTAX ClrRrmDot11BandGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents the RRM RF grouping on a dot11 band of an AP that has joined the controller. For each dot11 band an entry will be created." INDEX { clrRrmParametersType } ::= { clrRrmDot11BandGrpTable 1 } ClrRrmDot11BandGrpEntry ::= SEQUENCE { clrRrmDot11BandGrpLeaderIpAddressType InetAddressType, clrRrmDot11BandGrpLeaderIpAddress InetAddress, clrRrmDot11BandGrpLeaderName SnmpAdminString, clrRrmDot11BandGrpMode INTEGER, clrRrmDot11BandGrpRole INTEGER, clrRrmDot11BandGrpRestart TruthValue, clrRrmDot11BandGrpLastUpdateTime Unsigned32, clrRrmDot11BandGrpInterval Unsigned32, clrRrmDot11BandGrpLeaderIpv6AddressType InetAddressType, clrRrmDot11BandGrpLeaderIpv6Address InetAddress } clrRrmDot11BandGrpLeaderIpAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the group leader's address type for the dot11 group containing this controller. The only one address type supported is ipv4(1)." ::= { clrRrmDot11BandGrpEntry 1 } clrRrmDot11BandGrpLeaderIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the configured group leader's address for the dot11 group containing this controller." ::= { clrRrmDot11BandGrpEntry 2 } clrRrmDot11BandGrpLeaderName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the name of the current group leader." ::= { clrRrmDot11BandGrpEntry 3 } clrRrmDot11BandGrpMode OBJECT-TYPE SYNTAX INTEGER { automatic(1), off(2), leader(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the mode for the RRM algorithm for the band. 'automatic' - the controller form groups and elect leaders to perform better dynamic parameter optimization. 'leader' - the user can manually configure the group. 'off' - no dynamic grouping occurs. Each controller optimizes only its own APs' parameters." DEFVAL { automatic } ::= { clrRrmDot11BandGrpEntry 4 } clrRrmDot11BandGrpRole OBJECT-TYPE SYNTAX INTEGER { none(1), auto-leader(2), auto-member(3), static-leader(4), static-member(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the group role with respect to RRM RF grouping. The controller can be either group member or group leader while being in automatic or static grouping, for a particular band. If grouping is off , the value of the group role would be 'none'. 'none' - RRM RF Grouping is off 'auto-leader' - leader of automatic RRM RF Group 'auto-member' - member in automatic RRM RF Group 'static-leader' - leader of static RRM RF Group 'static-member' - member in static RRM RF Group." DEFVAL { auto-leader } ::= { clrRrmDot11BandGrpEntry 5 } clrRrmDot11BandGrpRestart OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether the grouping algorithm needs a restart. If a value of 'true' is set, the RRM grouping algorithm is restarted for the dot11 band. This will always return 'false' when retrieved" DEFVAL { false } ::= { clrRrmDot11BandGrpEntry 6 } clrRrmDot11BandGrpLastUpdateTime OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the last time the dot11 grouping was updated on this controller. This is valid only if the controller is not a static member in the group. If it is a static member (i.e the value of the variable ,'clrRrmDot11BandGrpMode' is 'static-member(4)'), a value of '0' would be returned always." ::= { clrRrmDot11BandGrpEntry 7 } clrRrmDot11BandGrpInterval OBJECT-TYPE SYNTAX Unsigned32 (0..600) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the period used by the grouping algorithm. The grouping algorithm runs when the group contents changes and automatic grouping is enabled. The system administrator can start grouping on demand." ::= { clrRrmDot11BandGrpEntry 8 } clrRrmDot11BandGrpLeaderIpv6AddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the IP address type of the RRM RF group leader." ::= { clrRrmDot11BandGrpEntry 9 } clrRrmDot11BandGrpLeaderIpv6Address OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the IPv6 address of the RRM RF group leader." ::= { clrRrmDot11BandGrpEntry 10 } -- ******************************************************************** -- * RRM RF Group Members -- ******************************************************************** clrRrmDot11BandGrpMemberTable OBJECT-TYPE SYNTAX SEQUENCE OF ClrRrmDot11BandGrpMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the information about the RRM grouping members corresponding to the dot11 band of the APs that have joined the controller. The entries are members of the group represented by clrRrmDot11BandGrpTable." ::= { clrRrmConfig 6 } clrRrmDot11BandGrpMemberEntry OBJECT-TYPE SYNTAX ClrRrmDot11BandGrpMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry describes the grouping members on a dot11 band of an AP that has joined the controller. An entry will be created/deleted when members are added/deleted to/from the gorup." INDEX { clrRrmParametersType, clrRrmDot11BandMemberIpAddressType, clrRrmDot11BandMemberIpAddress } ::= { clrRrmDot11BandGrpMemberTable 1 } ClrRrmDot11BandGrpMemberEntry ::= SEQUENCE { clrRrmDot11BandMemberIpAddressType InetAddressType, clrRrmDot11BandMemberIpAddress InetAddress, clrRrmDot11BandMemberName SnmpAdminString, clrRrmDot11BandMemberIsJoined TruthValue, clrRrmDot11BandMemberJoinFailureReason INTEGER, clrRrmDot11BandMemberRowStatus RowStatus } clrRrmDot11BandMemberIpAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the address type of the dot11 group member for the dot11 grouping containing this controller." ::= { clrRrmDot11BandGrpMemberEntry 1 } clrRrmDot11BandMemberIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the address of the dot11 group member for the dot11 grouping containing this controller." ::= { clrRrmDot11BandGrpMemberEntry 2 } clrRrmDot11BandMemberName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the name of the dot11 group member for the dot11 grouping containing this controller." ::= { clrRrmDot11BandGrpMemberEntry 3 } clrRrmDot11BandMemberIsJoined OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents whether the member has joined this RRM RF Group yet.If not the value would be 'false'. Else it would be true.This field is significant only if the current group is a static RRM RF Group. In all other cases a value of 'true' would be shown. true - member has joined the group successfully false - member has not joined the group yet." DEFVAL { true } ::= { clrRrmDot11BandGrpMemberEntry 4 } clrRrmDot11BandMemberJoinFailureReason OBJECT-TYPE SYNTAX INTEGER { joinedSuccessfully(1), invalidIp(2), groupSizeExceeded(3), invalidGroupOrder(4), nonMatchingGroupID(5), unexpectedError(6), weakSignalStrength(7), joinPending(8), notAManager(9), groupingDelayed(10), groupingDisabled(11), invalidProtocolVersion(12), countryCodeMismatch(13), invalidHierarchy(14), alreadyAStaticLeader(15), memberOfAnotherGroup(16), unconfiguredAsStaticMember(17), cntlrNameAndIpMismatch(18), unexpectedMemoryError(19), rfDomainMismatch(20), splitForInvalidStateRequest(21), transitioningToStaticFromAuto(22), splitDueToUserAction(23) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the reason the member could not join the RRM RF Group. This field is relevant only if the corresponding instance for 'clrRrmDot11BandMemberIsJoined' is 'false'. joinedSuccessfully - member has joined the group successfully invalidIp - invalid ip groupSizeExceeded - group size is exceeded invalidGroupOrder - group order is invalid nonMatchingGroupID - group id doesn't match unexpectedError - unexpected error has occurred weakSignalStrength - signal strength is weak joinPending - group join is pending notAManager - not a manager groupingDelayed - grouping is delayed groupingDisabled - grouping is disabled invalidProtocolVersion - protocol version is invalid countryCodeMismatch - country code doesn't match invalidHierarchy - invalid grouping hierarchy alreadyAStaticLeader - already a static leader memberOfAnotherGroup - member of another group unconfiguredAsStaticMember - unconfigured static member cntlrNameAndIpMismatch - controller name and ip doesn't match unexpectedMemoryError - an unexpected memory error has happened rfDomainMismatch - RF domain doesn't match. splitForInvalidStateRequest - split for invalid state request transitioningToStaticFromAuto - transitioning to static from auto splitDueToUserAction - split due to user action." DEFVAL { joinedSuccessfully } ::= { clrRrmDot11BandGrpMemberEntry 5 } clrRrmDot11BandMemberRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the status of the row." ::= { clrRrmDot11BandGrpMemberEntry 6 } clrRrmDcaConfig OBJECT IDENTIFIER ::= { clrRrmConfig 7 } clrRrmDcaDot11aOutdoorAPDca OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether check for non-DFS channel should be done on DCA channel list or not. Generally at least one non-DFS channel should be present in DCA channel list. But there are locations like EU(European Union) where there is no non-DFS channel available for outdoor deployment. Customers deploying outdoor APs in EU or regions with similar regulations should set this variable to 'true'. A value of 'true' indicates that controller will not perform check for non-DFS channels in DCA list. A value of 'false' indicates that controller will perform checkf for non-DFS channels in DCA list." ::= { clrRrmDcaConfig 1 } clrRrmRfGroupingPriority OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the priority assigned to controller with respect to RRM RF Grouping. When groups are formed, the priorities of the member controllers would be checked. Priority of the member controller should be less than or equal to priority of the leader controller." ::= { clrRrmConfig 8 } clrRrmDcaChannelListTable OBJECT-TYPE SYNTAX SEQUENCE OF ClrRrmDcaChannelListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains current channel information for an AP's 802.11 interface. Based on the country that an AP operates in, it gets assigned to a regulatory domain. For a given regulatory domain a fixed number of channels are assigned automatically to an AP for a given interface. This table represents this information. Entries are automatically created on the controller as APs associate. Entries are removed when the APs disassociate. User can add a channel in DCA or remove it from DCA using the clrRrmChannelTable. clrRrmDcaChannelListTable provides the list of current channels allocation for DCA." ::= { clrRrmConfig 9 } clrRrmDcaChannelListEntry OBJECT-TYPE SYNTAX ClrRrmDcaChannelListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table provides list of the channels that are used in DCA as well as not-used in DCA for an 802.11 interface in an AP." INDEX { clrRrmParametersType } ::= { clrRrmDcaChannelListTable 1 } ClrRrmDcaChannelListEntry ::= SEQUENCE { clrRrmDcaUsedChannelList SnmpAdminString, clrRrmDcaUnusedChannelList SnmpAdminString, clrRrmDcaDefaultChannelList SnmpAdminString } clrRrmDcaUsedChannelList OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the channels that are part of the Dynamic Channel Allocation (DCA) list. This is a comma separated list of used channel numbers." ::= { clrRrmDcaChannelListEntry 1 } clrRrmDcaUnusedChannelList OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the channels that are not part of the Dynamic Channel Allocation (DCA) list. This is a comma separated list of unused channel numbers." ::= { clrRrmDcaChannelListEntry 2 } clrRrmDcaDefaultChannelList OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the default DCA channels based on configured country code/country code list. This is a comma separated list of default DCA channel numbers." ::= { clrRrmDcaChannelListEntry 3 } clrRrmPakRssiConfig OBJECT IDENTIFIER ::= { clrRrmConfig 10 } clrRrmHyperLocationEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the state of Packet RSSI location feature. A value of 'true' indicates that PRL(Packet RSSI Location) is enabled. A value of 'false' indicates that PRL is disabled." DEFVAL { false } ::= { clrRrmPakRssiConfig 1 } clrRrmPakRssiThreshold OBJECT-TYPE SYNTAX Integer32 (-100..-50) UNITS "dbm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the threshold value for Packet RSSI location feature. Valid range is -100 dbm to -50 dbm." DEFVAL { -100 } ::= { clrRrmPakRssiConfig 2 } clrRrmPakRssiThresholdTrigger OBJECT-TYPE SYNTAX Integer32 UNITS "dbm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the trigger threshold value for Packet RSSI location feature. Valid range is 1 dbm to 100 dbm." DEFVAL { 10 } ::= { clrRrmPakRssiConfig 3 } clrRrmPakRssiNtpIpAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object specifies the NTP server IP address type for Packet RSSI location feature." DEFVAL { 1 } ::= { clrRrmPakRssiConfig 4 } clrRrmPakRssiNtp OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object specifies the NTP server IP for Packet RSSI location feature." DEFVAL { 0 } ::= { clrRrmPakRssiConfig 5 } clrRrmFraConfig OBJECT IDENTIFIER ::= { clrRrmConfig 11 } clrRrmFraEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the state of Flexible Radio Assignment(FRA)feature. A value of 'true' indicates that FRA is enabled. A value of 'false' indicates that FRA is disabled." DEFVAL { false } ::= { clrRrmFraConfig 1 } clrRrmFraInterval OBJECT-TYPE SYNTAX Integer32 UNITS "hours" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the FRA interval in hours for the FRA feature." DEFVAL { 1 } ::= { clrRrmFraConfig 2 } clrRrmFraSensitivity OBJECT-TYPE SYNTAX INTEGER { low(1), medium(2), high(3), higher(4), evenhigher(5), superhigh(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the sensitivity for the FRA feature low(1) - set the FRA sensistivity as low(100%). medium(2) - set the FRA sensitivity as medium(95%). high(3) - set the FRA sensitivity as high(90%). higher(4) - set the FRA sensitivity as higher(85%). evenhigher(5) - set the FRA sensitivity as evenhigher(80%). superhigh(6) - set the FRA sensitivity as superhigh(50%)." DEFVAL { low } ::= { clrRrmFraConfig 3 } clrRrmFraSensorThreshold OBJECT-TYPE SYNTAX INTEGER { clientPriority(0), clientPreferred(1), balanced(2), sensorPreferred(3), sensorPriority(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies threshold levels for Sensor Selection algorithm. Values offered can influence FRA algorithm's decision to provide less or more sensor radios for WSA service. ClientPriority will ensure highest(default) coverage for wireless clients and SensorPriority offers more sensor radios offered for WSA service, such threshold with weaker coverage for wireless clients." DEFVAL { clientPriority } ::= { clrRrmFraConfig 4 } clrRrmFraSensorCoverage OBJECT-TYPE SYNTAX Unsigned32 (1..100) UNITS "percent" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the overall sensor coverage for entire RRM Group. It will represent % of radios covered in the single RF domain." ::= { clrRrmFraConfig 5 } clrRrmFraServicePriority OBJECT-TYPE SYNTAX INTEGER { coverage(0), clientAware(1), serviceAssurance(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies service priority of flexible radio assignment algorithm.Coverage is the default state which will ensure good coverage for wireless clients. Client-Aware enables more 5GHz radios when network load is higher,Service-Assurance enables more sensors via excessive radios to ensure good sensor coverage for Wireless Service Assurance." DEFVAL { coverage } ::= { clrRrmFraConfig 6 } clrRrmFraSensorDensityOptimisationTargetRssi OBJECT-TYPE SYNTAX Integer32 UNITS "dbm" MAX-ACCESS read-only STATUS current DESCRIPTION "This value specifies receiver size cell for wireless clients. RSSI value in dBm will approximate downlink RSSI for wireless clients. Target RSSI represents rough coverage given by FRA enabled radio for clients." ::= { clrRrmFraConfig 7 } clrRrm11kConfig OBJECT IDENTIFIER ::= { clrRrmConfig 12 } clrRrm11kDenialMax OBJECT-TYPE SYNTAX Unsigned32 (1..10) UNITS "count" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the maximum number of times a client can be denied association if the association request that is sent to an AP does not match any AP in the prediction list." ::= { clrRrm11kConfig 1 } clrRrm11kFloorBias OBJECT-TYPE SYNTAX Unsigned32 (5..25) UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the neighbor floor label bias in dBm." ::= { clrRrm11kConfig 2 } clrRrm11kPredictionMin OBJECT-TYPE SYNTAX Unsigned32 (2..6) UNITS "count" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the minimum number of predicted APs required for the prediction list feature to be activated." ::= { clrRrm11kConfig 3 } clrRrmRemoveChannelTable OBJECT-TYPE SYNTAX SEQUENCE OF ClrRrmRemoveChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the removed channel information from default DCA channel list for an AP's 802.11 interface. Based on the country that an AP operates in, it gets assigned to a regulatory domain. For a given regulatory domain a fixed number of channels are assigned automatically to an AP for a given interface. We can remove a channel from this default DCA list and those channels will be put in this table. This table represents the removed channels information from the default DCA channel list. By default, there will not be any entries in this table. An entry can also be created or deleted from this table by using clrRrmChannelRowStatus." ::= { clrRrmConfig 13 } clrRrmRemoveChannelEntry OBJECT-TYPE SYNTAX ClrRrmRemoveChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table provides the removed channel information for an 802.11 interface from the default DCA channel list." INDEX { clrRrmParametersType, clrRrmRemoveChannelNum } ::= { clrRrmRemoveChannelTable 1 } ClrRrmRemoveChannelEntry ::= SEQUENCE { clrRrmRemoveChannelNum Unsigned32, clrRrmRemovedChannelDcaState TruthValue, clrRrmRemoveChannelRowStatus RowStatus } clrRrmRemoveChannelNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The channel nubmer for this entry. This value represents the unique channel number removed from the default DCA channel list for the 802.11 interface for this regulatory domain." ::= { clrRrmRemoveChannelEntry 1 } clrRrmRemovedChannelDcaState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies whether this channel is part of the dynamic channel allocation (DCA) Remove List. A value of 'false' indicates that the DCA for this channel is disabled." DEFVAL { false } ::= { clrRrmRemoveChannelEntry 2 } clrRrmRemoveChannelRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. All writable objects in this row may be modified at any time." ::= { clrRrmRemoveChannelEntry 3 } clrRrmAddChannelTable OBJECT-TYPE SYNTAX SEQUENCE OF ClrRrmAddChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the added channel information to the default DCA channel list for an AP's 802.11 interface. Based on the country that an AP operates in, it gets assigned to a regulatory domain. For a given regulatory domain a fixed number of channels are assigned automatically to an AP for a given interface. We can add a non-default DCA channel to this list and those channels will be put in this table. This table represents the added DCA channels information to the default DCA list. By default, there will not be any entries in this table. An entry can also be created or deleted by using clrRrmChannelRowStatus." ::= { clrRrmConfig 14 } clrRrmAddChannelEntry OBJECT-TYPE SYNTAX ClrRrmAddChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table provides the added channel information to the default DCA channel list for an 802.11 interface in an AP." INDEX { clrRrmParametersType, clrRrmAddChannelNum } ::= { clrRrmAddChannelTable 1 } ClrRrmAddChannelEntry ::= SEQUENCE { clrRrmAddChannelNum Unsigned32, clrRrmAddedChannelDcaState TruthValue, clrRrmAddChannelRowStatus RowStatus } clrRrmAddChannelNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The channel nubmer for this entry. This value represents the unique channel number added to the default DCA channel list on this 802.11 interface for this regulatory domain." ::= { clrRrmAddChannelEntry 1 } clrRrmAddedChannelDcaState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies whether this channel is part of the dynamic channel allocation (DCA) Add List. A value of 'true' indicates that the DCA for this channel is enabled." DEFVAL { true } ::= { clrRrmAddChannelEntry 2 } clrRrmAddChannelRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. All writable objects in this row may be modified at any time." ::= { clrRrmAddChannelEntry 3 } clrRrmDot11BandJoinedGrpMemberTable OBJECT-TYPE SYNTAX SEQUENCE OF ClrRrmDot11BandJoinedGrpMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the information about the RRM grouping members corresponding to the dot11 band of the APs that have joined the controller. The entries are members of the group represented by clrRrmDot11BandGrpTable." ::= { clrRrmConfig 15 } clrRrmDot11BandJoinedGrpMemberEntry OBJECT-TYPE SYNTAX ClrRrmDot11BandJoinedGrpMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry describes the grouping members on a dot11 band of an AP that has joined the controller. An entry will be created/deleted when members are added/deleted to/from the gorup." INDEX { clrRrmParametersType, clrRrmDot11BandJoinedMemberIpAddressType, clrRrmDot11BandJoinedMemberIpAddress } ::= { clrRrmDot11BandJoinedGrpMemberTable 1 } ClrRrmDot11BandJoinedGrpMemberEntry ::= SEQUENCE { clrRrmDot11BandJoinedMemberIpAddressType InetAddressType, clrRrmDot11BandJoinedMemberIpAddress InetAddress, clrRrmDot11BandJoinedMemberName SnmpAdminString, clrRrmDot11BandJoinedMemberIsJoined TruthValue, clrRrmDot11BandJoinedMemberJoinFailureReason INTEGER, clrRrmDot11BandJoinedMemberIpv6AddressType InetAddressType, clrRrmDot11BandJoinedMemberIpv6Address InetAddress } clrRrmDot11BandJoinedMemberIpAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the address type of the dot11 group member for the dot11 grouping containing this controller." ::= { clrRrmDot11BandJoinedGrpMemberEntry 1 } clrRrmDot11BandJoinedMemberIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the address of the dot11 group member for the dot11 grouping containing this controller." ::= { clrRrmDot11BandJoinedGrpMemberEntry 2 } clrRrmDot11BandJoinedMemberName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the name of the dot11 group member for the dot11 grouping containing this controller." ::= { clrRrmDot11BandJoinedGrpMemberEntry 3 } clrRrmDot11BandJoinedMemberIsJoined OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the member has joined this RRM RF Group yet. If not the value would be 'false'. Else it would be true. This field is significant only if the current group is a static RRM RF Group. In all other cases a value of 'true' would be shown. true - member has joined the group successfully false - member has not joined the group yet." DEFVAL { true } ::= { clrRrmDot11BandJoinedGrpMemberEntry 4 } clrRrmDot11BandJoinedMemberJoinFailureReason OBJECT-TYPE SYNTAX INTEGER { joinedSuccessfully(1), invalidIp(2), groupSizeExceeded(3), invalidGroupOrder(4), nonMatchingGroupID(5), unexpectedError(6), weakSignalStrength(7), joinPending(8), notAManager(9), groupingDelayed(10), groupingDisabled(11), invalidProtocolVersion(12), countryCodeMismatch(13), invalidHierarchy(14), alreadyAStaticLeader(15), memberOfAnotherGroup(16), unconfiguredAsStaticMember(17), cntlrNameAndIpMismatch(18), unexpectedMemoryError(19), rfDomainMismatch(20) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the reason the member could not join the RRM RF Group. This field is relevant only if the corresponding instance for 'clrRrmDot11BandMemberIsJoined' is 'false'. joinedSuccessfully - member has joined the group successfully invalidIp - invalid ip groupSizeExceeded - group size is exceeded invalidGroupOrder - group order is invalid nonMatchingGroupID - group id doesn't match unexpectedError - unexpected error has occurred weakSignalStrength - signal strength is weak joinPending - group join is pending notAManager - not a manager groupingDelayed - grouping is delayed groupingDisabled - grouping is disabled invalidProtocolVersion - protocol version is invalid countryCodeMismatch - country code doesn't match invalidHierarchy - invalid grouping hierarchy alreadyAStaticLeader - already a static leader memberOfAnotherGroup - member of another group unconfiguredAsStaticMember - unconfigured static member cntlrNameAndIpMismatch - controller name and ip doesn't match unexpectedMemoryError - an unexpected memory error has happened rfDomainMismatch - RF domain doesn't match." DEFVAL { joinedSuccessfully } ::= { clrRrmDot11BandJoinedGrpMemberEntry 5 } clrRrmDot11BandJoinedMemberIpv6AddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the IP address type of the member controller joined to the RRM RF group." ::= { clrRrmDot11BandJoinedGrpMemberEntry 6 } clrRrmDot11BandJoinedMemberIpv6Address OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the IPv6 address of the member controller joined to the RRM RF group." ::= { clrRrmDot11BandJoinedGrpMemberEntry 7 } clrRrmBcoTable OBJECT-TYPE SYNTAX SEQUENCE OF ClrRrmBcoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains configurations for the BSS Color Optimization (BCO) algorithm." ::= { clrRrmConfig 16 } clrRrmBcoEntry OBJECT-TYPE SYNTAX ClrRrmBcoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents the BSS Color Optimization (BCO) configuration for a dot11 band." INDEX { clrRrmParametersType } ::= { clrRrmBcoTable 1 } ClrRrmBcoEntry ::= SEQUENCE { clRrmBcoMode INTEGER } clRrmBcoMode OBJECT-TYPE SYNTAX INTEGER { automatic(1), static(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "BSS Color Optimization (BCO) has two modes. When the mode is auto, the BSS color will be dynamically updated for all access points that permit this operation. When BCO is static, no dynamic BSS color selections occur and the BSS color must be manually configured." DEFVAL { automatic } ::= { clrRrmBcoEntry 1 } clrRrmTriRadioConfig OBJECT IDENTIFIER ::= { clrRrmConfig 17 } clrRrmTriRadioMode OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the state of global tri-radio mode on the controller. A value of 'true' means global tri-radio mode is enabled. A value of 'false' indicates that the global tri-radio mode is disabled" DEFVAL { false } ::= { clrRrmTriRadioConfig 1 } -- ******************************************************************** -- * NOTIFICATION Variable -- ******************************************************************** clrRrmNotificationVariable OBJECT IDENTIFIER ::= { ciscoLwappRrmMIBObjects 2 } clrRrmApTransmitPowerLevel OBJECT-TYPE SYNTAX Integer32 (-200..200) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This indicates represents the transmit power level for the AP." ::= { clrRrmNotificationVariable 1 } clrRrmTimeStamp OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the time when coverage pre alarm was first reported to controller by an access point. After receiving this alert, controller will try to mitigate the coverage hole by increasing the transmit power of that access point. After doing above step for stipulated time, if coverage hole cannot be corrected by controller, a final notification would be generated from controller , informing the administrator about the existence of a coverage hole." ::= { clrRrmNotificationVariable 2 } clrRrmClientType OBJECT-TYPE SYNTAX INTEGER { data(1), voice(2) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the client type for which this notification was sent. data(1) - coverage hole has been detected for a data client(client which is meant for data services). voice(2) - coverage hole has been detected for a voice client(client which is meant for voice services)." ::= { clrRrmNotificationVariable 3 } clrRrmRssiHistogramLength OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the number of values on the histogram. At present it is 31 entries." ::= { clrRrmNotificationVariable 4 } clrRrmRssiHistogramMaxIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the maximum value on the histogram." ::= { clrRrmNotificationVariable 5 } clrRrmRssiHistogramMinIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the minimum value on the histogram." ::= { clrRrmNotificationVariable 6 } clrRrmRssiHistogramValues OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object returns a comma seperated string of histogram values. The number of values sent out is represented by the clrRrmRssiHistogramLength." ::= { clrRrmNotificationVariable 7 } clrRrmNeighborApCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the number of 'clrRrmNeighborApMac, clrRrmNeighborApRssi' appended to this notification. This count is 5 and includes the AP itself." ::= { clrRrmNotificationVariable 8 } clrRrmNeighborApMacAddress OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the neighbor MAC address for this client. This is a comma seperated values for clrRrmNeighborApCount values." ::= { clrRrmNotificationVariable 9 } clrRrmNeighborApRssi OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the neighbor RSSI values for this client. This is a comma seperated values for clrRrmNeighborApCount values." ::= { clrRrmNotificationVariable 10 } clrRrmNeighborApIfType OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the neighbor AP radio type for this client. This is a comma seperated values for clrRrmNeighborApCount values." ::= { clrRrmNotificationVariable 11 } clrRrmSysMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the MAC Address of the controller." ::= { clrRrmNotificationVariable 12 } clrRrmSysIdentifier OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the unique identifier for the controller." ::= { clrRrmNotificationVariable 13 } clrRrmRssiHistogramValuesRev OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the histogram value. When notfication is being sent, there would as many instances of this object as the vlaue of 'clrRrmRssiHistogramLength'." ::= { clrRrmNotificationVariable 14 } clrRrmNeighborApCountRev OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the number of 'clrRrmNeighborApMac, clrRrmNeighborApRssi' appended to this notification." ::= { clrRrmNotificationVariable 15 } clrRrmNeighborApMacAddressRev OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the neighbor MAC address for this client. This is a comma seperated values for clrRrmNeighborApCount values." ::= { clrRrmNotificationVariable 16 } clrRrmNeighborApRssiRev OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the neighbor RSSI values for this client. This is a comma seperated values for clrRrmNeighborApCount values." ::= { clrRrmNotificationVariable 17 } clrRrmNeighborApIfTypeRev OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the neighbor AP radio type for this client. This is a comma seperated values for clrRrmNeighborApCount values." ::= { clrRrmNotificationVariable 18 } clrRrmSysMacAddressRev OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the MAC Address of the controller." ::= { clrRrmNotificationVariable 19 } clrRrmSysIpAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the type of clrRrmSysIpAddress." ::= { clrRrmNotificationVariable 20 } clrRrmSysIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the IPv4 and IPv6 address of the controller." ::= { clrRrmNotificationVariable 21 } -- ******************************************************************** -- * NOTIFICATIONS -- ******************************************************************** ciscoLwappDot11ClientCoverageHolePreAlarm NOTIFICATION-TYPE OBJECTS { cldcClientMacAddress, cldcApMacAddress, cldcIfType, cLApName, clrRrmApTransmitPowerLevel, clrRrmTimeStamp, clrRrmClientType, clrRrmRssiHistogramLength, clrRrmRssiHistogramMaxIndex, clrRrmRssiHistogramMinIndex, clrRrmRssiHistogramValues, clrRrmNeighborApCount, clrRrmNeighborApMacAddress, clrRrmNeighborApRssi, clrRrmNeighborApIfType, cLWlanChdEnable } STATUS current DESCRIPTION "This notification is generated when the AP receives at least 'packet count' packets, represented by clrRrmParametersVoicePktCount for voice or clrRrmParametersDataPktCount for data, from a client in any given 5 second interval and 'packet percent' of the packets, represented by clrRrmParametersVoicePktCount for voice and clrRrmParametersDataPktCount for data, from the client are below the 'RSSI threshold' represented by clrRrmParametersVoiceRssiThreshold for voice and clrRrmParametersDataRssiThreshold for data." ::= { ciscoLwappRrmMIBNotifs 1 } ciscoLwappRrmRfGroupLeaderChange NOTIFICATION-TYPE OBJECTS { cldcIfType, clrRrmSysMacAddress, clrRrmSysIpAddress, clrRrmSysIdentifier } STATUS current DESCRIPTION "This notification would be generated, from the controller that is elected as the new leader, when RF Grouping is done. It has MAC address and details of the new Group Leader." ::= { ciscoLwappRrmMIBNotifs 2 } ciscoLwappRrmRfGroupMemberAdded NOTIFICATION-TYPE OBJECTS { cldcIfType, clrRrmSysMacAddress, clrRrmSysIpAddress, clrRrmSysIdentifier } STATUS current DESCRIPTION "This notification is generated from the group leader when a new member is added to the RF group. This notification has MAC address and details of new group member." ::= { ciscoLwappRrmMIBNotifs 3 } ciscoLwappRrmRfGroupMemberRemoved NOTIFICATION-TYPE OBJECTS { cldcIfType, clrRrmSysMacAddress, clrRrmSysIpAddress, clrRrmSysIdentifier } STATUS current DESCRIPTION "The notification is generated from the group leader, when a member is removed from the RF group. This notification has MAC address and details of removed group member." ::= { ciscoLwappRrmMIBNotifs 4 } ciscoLwappDot11ClientCoverageHolePreAlarmRev NOTIFICATION-TYPE OBJECTS { cldcClientMacAddress, cldcApMacAddress, cldcIfType, cLApName, clrRrmApTransmitPowerLevel, clrRrmTimeStamp, clrRrmClientType, clrRrmRssiHistogramLength, clrRrmRssiHistogramMaxIndex, clrRrmRssiHistogramMinIndex, clrRrmNeighborApCountRev, clrRrmNeighborApMacAddressRev, clrRrmNeighborApRssiRev, clrRrmNeighborApIfTypeRev, cLWlanChdEnable, clrRrmRssiHistogramValuesRev } STATUS current DESCRIPTION "The system generates this notification when the RRM coverage hole detection algorithm detects areas of radio coverage in a wireless LAN that are below the level needed for robust radio performance. If clients on a access point are detected at threshold levels (RSSI, percentage of failed packets, and number of failed packets) specified in RRM configuration, the access point sends a 'coverage hole' alert to the controller. This notification is generated in any of the following conditions 1)When the failed packet count is more than failed packet count threshold represented by clrRrmParametersVoicePktCountThreshold for voice and clrRrmParametersDataPktCountThreshold for data. 2)When the percentage of failed packet count is more than the failed packet count threshold represented by clrRrmParametersVoicePktPercentThreshold for voice and clrRrmParametersDataPktPercentThreshold for data. 3)When RSSI value is lower than the RSSI threshold represented by clrRrmParametersVoiceRssiThreshold for voice and clrRrmParametersDataRssiThreshold for data." ::= { ciscoLwappRrmMIBNotifs 5 } ciscoLwappRrmRfGroupLeaderChangeRev NOTIFICATION-TYPE OBJECTS { cldcIfType, clrRrmSysMacAddressRev, clrRrmSysIpAddressType, clrRrmSysIpAddress } STATUS current DESCRIPTION "This notification would be generated, from the controller that is elected as the new leader, when RF Grouping is done. It has MAC address and details of the new Group Leader." ::= { ciscoLwappRrmMIBNotifs 6 } ciscoLwappRrmRfGroupMemberAddedRev NOTIFICATION-TYPE OBJECTS { cldcIfType, clrRrmSysMacAddressRev, clrRrmSysIpAddressType, clrRrmSysIpAddress } STATUS current DESCRIPTION "This notification is generated from the group leader when a new member is added to the RF group. This notification has MAC address and details of new group member." ::= { ciscoLwappRrmMIBNotifs 7 } ciscoLwappRrmRfGroupMemberRemovedRev NOTIFICATION-TYPE OBJECTS { cldcIfType, clrRrmSysMacAddressRev, clrRrmSysIpAddressType, clrRrmSysIpAddress } STATUS current DESCRIPTION "The notification is generated from the group leader, when a member is removed from the RF group. This notification has MAC address and details of removed group member." ::= { ciscoLwappRrmMIBNotifs 8 } -- ******************************************************************** -- * Compliance statements -- ******************************************************************** -- ******************************************************************** ciscoLwappRrmMIBCompliances OBJECT IDENTIFIER ::= { ciscoLwappRrmMIBConform 1 } ciscoLwappRrmMIBGroups OBJECT IDENTIFIER ::= { ciscoLwappRrmMIBConform 2 } -- ******************************************************************** -- * Units of conformance -- ******************************************************************** -- STATUS deprecated by ciscoLwappRrmMIBComplianceRev1 ciscoLwappRrmMIBCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappRrmMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappRrmConfigGroup } ::= { ciscoLwappRrmMIBCompliances 1 } -- STATUS deprecated by ciscoLwappRrmMIBComplianceRev2 ciscoLwappRrmMIBComplianceRev1 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappRrmMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappRrmConfigGroup } GROUP ciscoLwappRrmConfigGroupSup1 DESCRIPTION "Implementation of this group is mandatory for controllers that support CHD (Coverage Hole Detection)." ::= { ciscoLwappRrmMIBCompliances 2 } ciscoLwappRrmMIBComplianceRev2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappRrmMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappRrmConfigGroupSup2 } GROUP ciscoLwappRrmConfigGroupSup1 DESCRIPTION "Implementation of this group is mandatory for controllers that support CHD (Coverage Hole Detection)." GROUP ciscoLwappRrmConfigGroupSup3 DESCRIPTION "Implementation of this group is mandatory for controllers that supports TPC (Transmission Power Control)." GROUP ciscoLwappRrmConfigGroupSup4 DESCRIPTION "Implementation of this group is mandatory for controllers that supports RRM RF Grouping." GROUP ciscoLwappRrmGrpStatusGroup DESCRIPTION "Implementation of this status group is mandatory for controllers that supports RRM RF Grouping." ::= { ciscoLwappRrmMIBCompliances 3 } ciscoLwappRrmMIBComplianceRev3 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappRrmMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappRrmConfigGroupSup7 } GROUP ciscoLwappRrmConfigGroupSup1 DESCRIPTION "Implementation of this group is mandatory for controllers that support CHD (Coverage Hole Detection)." GROUP ciscoLwappRrmConfigGroupSup3 DESCRIPTION "Implementation of this group is mandatory for controllers that supports TPC (Transmission Power Control)" GROUP ciscoLwappRrmConfigGroupSup4 DESCRIPTION "Implementation of this group is mandatory for controllers that supports RRM RF Grouping." GROUP ciscoLwappRrmConfigGroupSup5 DESCRIPTION "Implementation of this group is mandatory for controllers that support CHD (Coverage Hole Detection)." GROUP ciscoLwappRrmGrpStatusGroup DESCRIPTION "Implementation of this status group is mandatory for controllers that supports RRM RF Grouping" GROUP ciscoLwappRrmChannelStatusGroup DESCRIPTION "Implementation of this group is mandatory for the devices which support creation or deletion of 802.11 channels." GROUP ciscoLwappRrmParametersGroup DESCRIPTION "Implementation of this group is mandatory for the devices which support additional RRM parameters for 802.11 channels." GROUP ciscoLwappRrmDcaChannelListGroup DESCRIPTION "Implementation of this group is optional for the devices which support enabling or disabling 802.11 channels for DCA." GROUP ciscoLwappRrmFraConfigGroup DESCRIPTION "Implementation of this group is optional for the devices which has XOR radio." GROUP ciscoLwappRrmConfigGroupSup6 DESCRIPTION "Implementation of this group is optional based upon client or network preference." GROUP ciscoLwappRrmNotifsGroup DESCRIPTION "Implementation of this groups sends notifications by the agent related to management station regarding RRM." GROUP ciscoLwappRrmNotifyObjectsGroup DESCRIPTION "Implementation of this groups sends notifications by the agent related to management station regarding RRM." GROUP ciscoLwappRrmPakRssiConfigGroup DESCRIPTION "Implementation of this group is necessary to configure hyperlocation /fastlocate for APs that belong to a user defined group." GROUP ciscoLwappRrmChdConfigGroup DESCRIPTION "Implementation of this group is mandatory for controllers that support CHD (Coverage Hole Detection)." GROUP ciscoLwappRrmOptRoamGroup DESCRIPTION "Implementation of this group is mandatory for controllers that support Optimized Roaming." OBJECT clrRrmParametersChdEnable MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersVoicePktCountThreshold MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersVoicePktPercentThreshold MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersVoiceRssiThreshold MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersDataPktCountThreshold MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersDataPktPercentThreshold MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersDataRssiThreshold MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersMaxTxPower MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersMinTxPower MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersTpcVersion MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersChdNoise MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersChdInterference MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersChdLoad MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersChdSignal MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersChdDevice MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersMaxClients WRITE-SYNTAX Unsigned32(1..200) MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersRssiCheckEnable MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersRssiThreshold MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersOptRoamEnable MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersOptRoamDataRate MIN-ACCESS read-only DESCRIPTION "read-write access is not required." OBJECT clrRrmParametersOptRoamInterval MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmParametersClientNetworkPreference MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmChannelDcaState MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmChannelRowStatus MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmDot11BandGrpLeaderIpAddressType MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmDot11BandGrpLeaderIpAddress MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmDot11BandGrpLeaderName MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmDot11BandGrpMode MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmDot11BandGrpRole MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmDot11BandGrpRestart MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmDot11BandGrpLastUpdateTime MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmDot11BandGrpInterval MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmDot11BandMemberName MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmDot11BandMemberIsJoined MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmDot11BandMemberJoinFailureReason MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmDot11BandMemberRowStatus MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmDcaDot11aOutdoorAPDca MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmRfGroupingPriority MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmDcaUsedChannelList MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmDcaUnusedChannelList MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmHyperLocationEnable MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmPakRssiThreshold MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmPakRssiThresholdTrigger MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmPakRssiNtpIpAddressType MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmPakRssiNtp MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmFraEnable MIN-ACCESS read-only DESCRIPTION "write access is not required." OBJECT clrRrmFraInterval MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT clrRrmFraSensitivity DESCRIPTION "Write access is not required." OBJECT clrRrmApTransmitPowerLevel DESCRIPTION "Write access is not required." OBJECT clrRrmTimeStamp DESCRIPTION "Write access is not required." OBJECT clrRrmClientType DESCRIPTION "Write access is not required." OBJECT clrRrmRssiHistogramLength DESCRIPTION "Write access is not required." OBJECT clrRrmRssiHistogramMaxIndex DESCRIPTION "Write access is not required." OBJECT clrRrmRssiHistogramMinIndex DESCRIPTION "Write access is not required." OBJECT clrRrmRssiHistogramValuesRev DESCRIPTION "Write access is not required." OBJECT clrRrmNeighborApCountRev DESCRIPTION "Write access is not required." OBJECT clrRrmNeighborApMacAddressRev DESCRIPTION "Write access is not required." OBJECT clrRrmNeighborApRssiRev DESCRIPTION "Write access is not required." OBJECT clrRrmNeighborApIfTypeRev DESCRIPTION "Write access is not required." OBJECT clrRrmSysMacAddressRev DESCRIPTION "Write access is not required." OBJECT clrRrmSysIpAddressType DESCRIPTION "Write access is not required." OBJECT clrRrmSysIpAddress DESCRIPTION "Write access is not required." ::= { ciscoLwappRrmMIBCompliances 4 } ciscoLwappRrmMIBComplianceRev4 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the SNMP entities that implement the ciscoLwappRrmMIB module." MODULE -- this module MANDATORY-GROUPS { ciscoLwappRrmConfigGroupSup8 } GROUP ciscoLwappRrmConfigGroupSup1 DESCRIPTION "Implementation of this group is mandatory for controllers that support CHD (Coverage Hole Detection)." GROUP ciscoLwappRrmConfigGroupSup3 DESCRIPTION "Implementation of this group is mandatory for controllers that supports TPC (Transmission Power Control)." GROUP ciscoLwappRrmConfigGroupSup4 DESCRIPTION "Implementation of this group is mandatory for controllers that supports RRM RF Grouping." GROUP ciscoLwappRrmGrpStatusGroup DESCRIPTION "Implementation of this status group is mandatory for controllers that supports RRM RF Grouping." GROUP ciscoLwappRrmChannelStatusGroup DESCRIPTION "Implementation of this group is mandatory for the devices which support creation or deletion of 802.11 channels." GROUP ciscoLwappRrmParametersGroup DESCRIPTION "Implementation of this group is mandatory for the devices which support additional RRM parameters for 802.11 channels." GROUP ciscoLwappRrmDcaChannelListGroup DESCRIPTION "Implementation of this group is optional for the devices which support enabling or disabling 802.11 channels for DCA." GROUP ciscoLwappRrmConfigGroupSup5 DESCRIPTION "Implementation of this group is mandatory for the devices which support deletion of 802.11 channels." GROUP ciscoLwappRrmConfigGroupSup9 DESCRIPTION "Implementation of this group is mandatory for controllers that supports RRM RF Grouping." OBJECT clrRrmChannelRowStatus SYNTAX INTEGER { active(1) } WRITE-SYNTAX INTEGER { createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "read-create access is not required." OBJECT clrRrmParametersTpcVersion MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT clrRrmParametersMaxClients MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT clrRrmParametersChdNoise MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT clrRrmParametersChdInterference MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT clrRrmParametersChdLoad MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT clrRrmParametersChdSignal MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT clrRrmParametersChdDevice MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT clrRrmDcaUsedChannelList DESCRIPTION "Write access is not required." OBJECT clrRrmDcaUnusedChannelList DESCRIPTION "Write access is not required." OBJECT clrRrmRemoveChannelRowStatus SYNTAX INTEGER { active(1) } WRITE-SYNTAX INTEGER { createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "read-create access is not required." ::= { ciscoLwappRrmMIBCompliances 5 } ciscoLwappRrmConfigGroup OBJECT-GROUP OBJECTS { clrRrmParametersPicoCellMode, clrRrmTupleRxSenseThresholdMin, clrRrmTupleRxSenseThresholdMax, clrRrmTupleRxSenseThreshold, clrRrmTupleCcaSenseThresholdMin, clrRrmTupleCcaSenseThresholdMax, clrRrmTupleCcaSenseThreshold, clrRrmTupleTransmitPowerLevelMin, clrRrmTupleTransmitPowerLevelMax, clrRrmTupleTransmitPowerLevel, clrRrmTupleSetDefault, clrRrmChannelDcaState } STATUS deprecated DESCRIPTION "This collection of objects represent the RRM configuration on the controller. ciscoLwappRrmConfigGroup object is superseded by ciscoLwappRrmConfigGroupSup1 ." ::= { ciscoLwappRrmMIBGroups 1 } ciscoLwappRrmConfigGroupSup1 OBJECT-GROUP OBJECTS { clrRrmParametersChdEnable, clrRrmParametersVoicePktCountThreshold, clrRrmParametersVoicePktPercentThreshold, clrRrmParametersVoiceRssiThreshold, clrRrmParametersDataPktCountThreshold, clrRrmParametersDataPktPercentThreshold, clrRrmParametersDataRssiThreshold } STATUS current DESCRIPTION "This collection of objects represents the RRM configuration for Voice and Data packets on the controller." ::= { ciscoLwappRrmMIBGroups 2 } ciscoLwappRrmConfigGroupSup2 OBJECT-GROUP OBJECTS { clrRrmChannelDcaState, clrRrmParametersDcaChannelWidth, clrRrmDcaDot11aOutdoorAPDca } STATUS deprecated DESCRIPTION "This collection of objects represent the RRM configuration on the controller." ::= { ciscoLwappRrmMIBGroups 3 } ciscoLwappRrmConfigGroupSup3 OBJECT-GROUP OBJECTS { clrRrmParametersMaxTxPower, clrRrmParametersMinTxPower } STATUS current DESCRIPTION "This collection of objects represent the Transmission Power Control(TPC) configuration on the controller, when the same is enabled on the controller." ::= { ciscoLwappRrmMIBGroups 4 } ciscoLwappRrmConfigGroupSup4 OBJECT-GROUP OBJECTS { clrRrmDot11BandGrpMode, clrRrmDot11BandGrpRestart, clrRrmDot11BandMemberName, clrRrmDot11BandMemberRowStatus } STATUS current DESCRIPTION "This collection of objects represent the RRM RF Grouping configuration on the controller, when the same is enabled on the controller." ::= { ciscoLwappRrmMIBGroups 5 } ciscoLwappRrmGrpStatusGroup OBJECT-GROUP OBJECTS { clrRrmDot11BandGrpLeaderIpAddressType, clrRrmDot11BandGrpLeaderIpAddress, clrRrmDot11BandGrpLeaderName, clrRrmDot11BandGrpRole, clrRrmDot11BandGrpLastUpdateTime, clrRrmDot11BandGrpInterval, clrRrmDot11BandMemberIsJoined, clrRrmDot11BandMemberJoinFailureReason, clrRrmDot11BandGrpLeaderIpv6AddressType, clrRrmDot11BandGrpLeaderIpv6Address } STATUS current DESCRIPTION "This collection of objects represent the status of RRM RF Groping on the controller, when the same is enabled on the controller." ::= { ciscoLwappRrmMIBGroups 6 } ciscoLwappRrmChannelStatusGroup OBJECT-GROUP OBJECTS { clrRrmChannelRowStatus } STATUS current DESCRIPTION "A collection of objects providing creation or deletion of 802.11 channels." ::= { ciscoLwappRrmMIBGroups 7 } ciscoLwappRrmParametersGroup OBJECT-GROUP OBJECTS { clrRrmParametersTpcVersion, clrRrmParametersMaxClients, clrRrmParametersChdNoise, clrRrmParametersChdInterference, clrRrmParametersChdLoad, clrRrmParametersChdSignal, clrRrmParametersChdDevice } STATUS current DESCRIPTION "This collection of objects represent the RRM parameters for a 802.11 interface type." ::= { ciscoLwappRrmMIBGroups 8 } ciscoLwappRrmNotifsGroup NOTIFICATION-GROUP NOTIFICATIONS { ciscoLwappDot11ClientCoverageHolePreAlarmRev, ciscoLwappRrmRfGroupLeaderChangeRev, ciscoLwappRrmRfGroupMemberAddedRev, ciscoLwappRrmRfGroupMemberRemovedRev } STATUS current DESCRIPTION "This collection of objects provides the information about the notifications sent by the agent related to RRM." ::= { ciscoLwappRrmMIBGroups 9 } ciscoLwappRrmDcaChannelListGroup OBJECT-GROUP OBJECTS { clrRrmDcaUsedChannelList, clrRrmDcaUnusedChannelList, clrRrmDcaDefaultChannelList } STATUS current DESCRIPTION "This collection of objects represent the channels used in DCA as well as not used in DCA for APs." ::= { ciscoLwappRrmMIBGroups 10 } ciscoLwappRrmConfigGroupSup5 OBJECT-GROUP OBJECTS { clrRrmRfGroupingPriority } STATUS current DESCRIPTION "This collection of objects represent the RRM configuration on the controller." ::= { ciscoLwappRrmMIBGroups 11 } ciscoLwappRrmFraConfigGroup OBJECT-GROUP OBJECTS { clrRrmFraEnable, clrRrmFraInterval, clrRrmFraSensitivity, clrRrmFraSensorThreshold, clrRrmFraSensorCoverage, clrRrmFraServicePriority, clrRrmFraSensorDensityOptimisationTargetRssi } STATUS current DESCRIPTION "This collection of objects represent the Flexible Radio Assignment (FRA) configuration on the controller." ::= { ciscoLwappRrmMIBGroups 12 } ciscoLwappRrmConfigGroupSup6 OBJECT-GROUP OBJECTS { clrRrmParametersClientNetworkPreference } STATUS current DESCRIPTION "This collection of objects represent the RRM configuration on the controller." ::= { ciscoLwappRrmMIBGroups 13 } ciscoLwappRrmChdConfigGroup OBJECT-GROUP OBJECTS { clrRrmParametersChdNoise, clrRrmParametersChdInterference, clrRrmParametersChdLoad, clrRrmParametersChdSignal, clrRrmParametersChdDevice } STATUS current DESCRIPTION "This collection of objects represent the Coverage Hold Detection(CHD) configuration on the controller, when the same is enabled on the controller." ::= { ciscoLwappRrmMIBGroups 14 } ciscoLwappRrmOptRoamGroup OBJECT-GROUP OBJECTS { clrRrmParametersOptRoamEnable, clrRrmParametersOptRoamDataRate, clrRrmParametersOptRoamInterval, clrRrmParametersRssiCheckEnable, clrRrmParametersRssiThreshold } STATUS current DESCRIPTION "This collection of objects represent the Optimized Roaming configuration on the controller, when the same is enabled on the controller." ::= { ciscoLwappRrmMIBGroups 15 } ciscoLwappRrmPakRssiConfigGroup OBJECT-GROUP OBJECTS { clrRrmHyperLocationEnable, clrRrmPakRssiThreshold, clrRrmPakRssiThresholdTrigger, clrRrmPakRssiNtpIpAddressType, clrRrmPakRssiNtp } STATUS current DESCRIPTION "This collection of objects represent the Packet RSSI configuration on the controller, when the same is enabled on the controller." ::= { ciscoLwappRrmMIBGroups 16 } ciscoLwappRrmNotifyObjectsGroup OBJECT-GROUP OBJECTS { clrRrmApTransmitPowerLevel, clrRrmTimeStamp, clrRrmClientType, clrRrmRssiHistogramLength, clrRrmRssiHistogramMaxIndex, clrRrmRssiHistogramMinIndex, clrRrmRssiHistogramValuesRev, clrRrmNeighborApCountRev, clrRrmNeighborApMacAddressRev, clrRrmNeighborApRssiRev, clrRrmNeighborApIfTypeRev, clrRrmSysMacAddressRev, clrRrmSysIpAddressType, clrRrmSysIpAddress } STATUS current DESCRIPTION "This collection of objects provide the information about RRM trap configuration and trap definition. These objects are defined under ciscoLwappRrmNotifObjects." ::= { ciscoLwappRrmMIBGroups 17 } ciscoLwappRrmConfigGroupSup7 OBJECT-GROUP OBJECTS { clrRrmChannelDcaState, clrRrmDcaDot11aOutdoorAPDca } STATUS current DESCRIPTION "This collection of objects represent the RRM configuration on the controller." ::= { ciscoLwappRrmMIBGroups 18 } ciscoLwappRrmConfigGroupSup8 OBJECT-GROUP OBJECTS { clrRrmRemovedChannelDcaState, clrRrmRemoveChannelRowStatus, clrRrmAddedChannelDcaState, clrRrmAddChannelRowStatus } STATUS current DESCRIPTION "This collection of objects represent the RRM Dca configuration on the controller." ::= { ciscoLwappRrmMIBGroups 19 } ciscoLwappRrmConfigGroupSup9 OBJECT-GROUP OBJECTS { clrRrmDot11BandJoinedMemberName, clrRrmDot11BandJoinedMemberIsJoined, clrRrmDot11BandMemberName, clrRrmDot11BandJoinedMemberJoinFailureReason, clrRrmDot11BandJoinedMemberIpv6AddressType, clrRrmDot11BandJoinedMemberIpv6Address } STATUS current DESCRIPTION "This collection of objects represents RRM Grouping configuration corresponding to dot11 band of APs joined to the controller, when the same is enabled on the controller." ::= { ciscoLwappRrmMIBGroups 20 } END