-- *****************************************************************
-- CISCO-FIBRECHANNEL-MIB.my
-- Fibre Channel INTERFACE MIB
--
-- May 2021 Rahul Shivaprasad (rshivapr)
--
-- Copyright (c) 2021 by Cisco Systems, Inc.
-- All rights reserved.
-- *****************************************************************

CISCO-FIBRECHANNEL-MIB DEFINITIONS ::= BEGIN

IMPORTS
    MODULE-IDENTITY,
    OBJECT-TYPE,
    NOTIFICATION-TYPE,
    Integer32,
    Unsigned32
        FROM SNMPv2-SMI
    TEXTUAL-CONVENTION,
    TruthValue,
    DisplayString,
    MacAddress,
    TimeStamp
        FROM SNMPv2-TC
    MODULE-COMPLIANCE,
    OBJECT-GROUP,
    NOTIFICATION-GROUP
        FROM SNMPv2-CONF
    ifIndex,
    ifName
        FROM IF-MIB
    ciscoMgmt
        FROM CISCO-SMI;

ciscoFibreChanMIB MODULE-IDENTITY
    LAST-UPDATED    "202105070000Z"
    ORGANIZATION    "Cisco Systems, Inc."
    CONTACT-INFO
            "Cisco Systems
            Customer Service

            Postal: 170 W Tasman Drive
            San Jose, CA  95134
            USA

            Tel: +1 800 553-NETS

            E-mail: cs-<list>@cisco.com"
    DESCRIPTION
        "This MIB module defines the managed objects for physical layer
        characteristics of Fibre Channel interfaces and performance
        statistics objects for protocol specific counters in Fibre Channel
        devices.
        Performance monitoring (PM) parameters are used by service
        providers to gather, store, set thresholds for and report
        performance data for early detection of problems.
        Thresholds are used to set error levels for each PM parameter.
        During the accumulation cycle, if the current value of a
        performance monitoring parameter reaches or exceeds its
        corresponding threshold value, a threshold crossing alarm (TCA)
        is generated. The TCAs provide early detection of performance
        degradation."
        ::= { ciscoMgmt 1053 }

-- Textual Conventions

CoiIntervalType ::= TEXTUAL-CONVENTION
    STATUS          current
    DESCRIPTION
        "This value indicates the time period over which performance
        monitoring data has been collected. Valid values are -

        fifteenMin(1)  -  values for the 15 min interval.
        oneDay(2)      -  values for the 1  Day interval.
        thirtySeconds(3) - values for the 30 second interval"
    SYNTAX          INTEGER  {
                        fifteenMin(1),
                        oneDay(2),
                        thirtySeconds(3)
                    }
-- Textual Conventions definition will be defined before this line

-- MIB Notification Definitions

ciscoFibreChanMIBNotifs  OBJECT IDENTIFIER
    ::= { ciscoFibreChanMIB 0 }

-- MIB Object Definitions 

ciscoFibreChanMIBObjects  OBJECT IDENTIFIER
    ::= { ciscoFibreChanMIB 1 }

coiFibreChanController OBJECT IDENTIFIER
    ::= { ciscoFibreChanMIBObjects 1 }

coiFcPm OBJECT IDENTIFIER
    ::= { ciscoFibreChanMIBObjects 2 }

coiFecPm OBJECT IDENTIFIER
    ::= { ciscoFibreChanMIBObjects 3 }

coiPcsPm OBJECT IDENTIFIER
    ::= { ciscoFibreChanMIBObjects 4 }

coiFibreChanControllerTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF CoiFibreChanControllerEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "This table provides management information for physical layer
        related attributes of interfaces with an ifType of
        FibreChannel(56)" 
    ::= { coiFibreChanController 1 }

coiFibreChanControllerEntry OBJECT-TYPE
    SYNTAX          CoiFibreChanControllerEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "An entry containing management information on physical layer
        related attributes of interfaces with an ifType
        FibreChannel(56). Entries are created by the feature when a
        new interface is added. Entries are deleted by the agent 
        when an interface is removed."
    INDEX   { ifIndex }
    ::= { coiFibreChanControllerTable 1 }


CoiFibreChanControllerEntry ::= SEQUENCE {
        coiFibreChanControllerAdminStatus               INTEGER,
        coiFibreChanControllerOperStatus                INTEGER,
        coiFibreChanControllerLoopbackInfo              INTEGER,
        coiFibreChanControllerAlarmStatus               BITS
        }


coiFibreChanControllerAdminStatus OBJECT-TYPE
    SYNTAX          INTEGER  {
                        down(0),
                        up(1)
                    }
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the administration status
        of the Fibre Channel interfaces. when it is set to down(0),
        it results in transmitted being stopped and there should be 
        corresponding change in coiFibreChanControllerOperStatus. 
        Valid values are :
        down(0):          The controller is in down state. 
        up(1):            The controller is in up state" 
    ::= { coiFibreChanControllerEntry 1 }

coiFibreChanControllerOperStatus OBJECT-TYPE
    SYNTAX          INTEGER  {
                        down(0),
                        up(1)
                        }
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the current operational state of the 
        Fibre Channel controller, valid values are -
        down(0):          The controller is in down state.
        up(1):            The controller is in up state.
        If coiFibreChanControllerAdminStatus is down(0) then 
        coiFibreChanControllerOperStatus should be down(0). If 
        coiFibreChanControllerAdminStatus is changed to up(1) then
        coiFibreChanControllerOperStatus should change to up(1), provided
        the controller is operational and ready to transmit traffic.
        It should remain in down(0) if there is a fault that prevents
        it from going to the up(1) state. " 
    ::= { coiFibreChanControllerEntry 2 }

coiFibreChanControllerLoopbackInfo OBJECT-TYPE
    SYNTAX          INTEGER  {
                        loopbackNone(0),
                        loopbackLine(1),
                        loopbackInternal(2)
                    }
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the loopback value of the Fibre Channel controller,
        valid values are -
        loopbackNone(0):       No controller loopback info
        loopbackLine(1):       The controller loopback info is line level  
        loopbackInternal(2):   The controller loopback info is internal level. "
    ::= { coiFibreChanControllerEntry 3 }

coiFibreChanControllerAlarmStatus OBJECT-TYPE
    SYNTAX          BITS {
                        noAlarm(0),
                        los(1),
                        syncLoss(2),
                        pcsErr(3),
                        hiBer(4),
                        localFault(5),
                        remoteFault(6),
                        nos(7),
                        squelch(8)
                    }
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates the current defect status of the Fibre Channel 
        controller. Valid values are - 
         noAlarm(0):     No Alarm. This bit will be set when none of the 
                         following defect bits are set.
         los(1):         LOS (Loss Of Signal). This bit will be set when
                         LOS alarm condition is detected on the Fibre Channel
                         Recieve side.
         syncLoss(2):    Sync Loss alarm.
         pcsErr(3):      PCS (Physical Coding Sublayer) Error alarm.
         hiBer(4):       high BER(Block Errored Seconds Ratio) alarm.
         localFault(5):  Local Fault alarm.
         remoteFault(6): Remote Fault alarm.
         nos(7):         NOS (Not-Operational primitive Sequence).
         squelch(8):     Squelch alarm."
    ::= { coiFibreChanControllerEntry 4 }

coiFcPmCurrentTable OBJECT IDENTIFIER
    ::= { coiFcPm 1 }

coiFcPmCurrentEntry OBJECT-TYPE
    SYNTAX          CoiFcPmCurrentEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "An entry containing Fibre Channel layer performance monitoring current interval data
        for Fibre Channel Controller."
    INDEX           {
                        ifIndex,
                        coiFcPmCurrentIntervalType
                    }
    ::= { coiFcPmCurrentTable 1 }
    
CoiFcPmCurrentEntry ::= SEQUENCE {
        coiFcPmCurrentIntervalType      CoiIntervalType,
        coiFcPmIfInOctets               Counter64,
        coiFcPmRxTotalPkts              Counter64,
        coiFcPmIfInErrors               Counter64,
        coiFcPmRxBadFcs                 Counter64,
        coiFcPmRxFramesTooShort         Counter64,
        coiFcPmRxFramesTooLong          Counter64,
        coiFcPmIfOutOctets              Counter64,
        coiFcPmTxTotalPkts              Counter64,
        coiFcPmTxBadFcs                 Counter64,
        coiFcPmTxFramesTooShort         Counter64,
        coiFcPmTxFramesTooLong          Counter64,
        coiFcCurrentPmValidData         TruthValue
}

coiFcPmCurrentIntervalType OBJECT-TYPE
    SYNTAX          CoiIntervalType
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the interval type for which Fibre Channel layer
         current performance monitoring data is collected."
    ::= { coiFcPmCurrentEntry 1 }

coiFcPmIfInOctets OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of bytes received since the last counter reset."
    ::= { coiFcPmCurrentEntry 2 }

coiFcPmRxTotalPkts OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of receive packets."
    ::= { coiFcPmCurrentEntry 3 }

coiFcPmIfInErrors OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of receive errors."
    ::= { coiFcPmCurrentEntry 4 }

coiFcPmRxBadFcs OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of received frames with bad FCS, no coding error."
    ::= { coiFcPmCurrentEntry 5 }

coiFcPmRxFramesTooShort OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of truncated received frames."
    ::= { coiFcPmCurrentEntry 6 }

coiFcPmRxFramesTooLong OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of too long received frames."
    ::= { coiFcPmCurrentEntry 7 }

coiFcPmIfOutOctets OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of octets transmitted out of the interface,
         including framing characters."
    ::= { coiFcPmCurrentEntry 8 }

coiFcPmTxTotalPkts OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of transmitted packets."
    ::= { coiFcPmCurrentEntry 9 }

coiFcPmTxBadFcs OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of transmitted frames with bad FCS, no coding error."
    ::= { coiFcPmCurrentEntry 10 }

coiFcPmTxFramesTooShort OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of truncated transmitted frames."
    ::= { coiFcPmCurrentEntry 11 }

coiFcPmTxFramesTooLong OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of too long transmitted frames."
    ::= { coiFcPmCurrentEntry 12 }

coiFcCurrentPmValidData OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This variable indicates if the Fibre Channel layer performance monitoring data for the
         interval identified by coiFcPmCurrentIntervalType is valid."
    ::= { coiFcPmCurrentEntry 13 }

coiFcPmHistoryTable OBJECT IDENTIFIER
    ::= { coiFcPm 2 }

coiFcPmHistoryEntry OBJECT-TYPE
    SYNTAX          CoiFcPmHistoryEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "An entry containing Fibre Channel layer performance monitoring historical interval data
        for Fibre Channel Controller."
    INDEX           { 
                        ifIndex,
                        coiFcPmHistoryIntervalType,
                        coiFcPmIntervalNumber
                    }
    ::= { coiFcPmHistoryTable 1 }
    
CoiFcPmHistoryEntry ::= SEQUENCE {
        coiFcPmHistoryIntervalType             CoiIntervalType,
        coiFcPmIntervalNumber                    Unsigned32,
        coiFcPmHistoryIfInOctets               Counter64,
        coiFcPmHistoryRxTotalPkts              Counter64,
        coiFcPmHistoryIfInErrors               Counter64,
        coiFcPmHistoryRxBadFcs                 Counter64,
        coiFcPmHistoryRxFramesTooShort         Counter64,
        coiFcPmHistoryRxFramesTooLong          Counter64,
        coiFcPmHistoryIfOutOctets              Counter64,
        coiFcPmHistoryTxTotalPkts              Counter64,        
        coiFcPmHistoryTxBadFcs                 Counter64,
        coiFcPmHistoryTxFramesTooShort         Counter64,
        coiFcPmHistoryTxFramesTooLong          Counter64,
        coiFcPmHistoryValidData                TruthValue
}

coiFcPmHistoryIntervalType OBJECT-TYPE
    SYNTAX          CoiIntervalType
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the interval type for which Fibre Channel layer
         historical performance monitoring data is collected."
    ::= { coiFcPmHistoryEntry 1 }

coiFcPmIntervalNumber OBJECT-TYPE
    SYNTAX          Unsigned32 (1..32)
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "This object gives the interval number for Fibre Channel layer
         performance monitoring data in given interval."
    ::= { coiFcPmHistoryEntry 2 }

coiFcPmHistoryIfInOctets OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of bytes received since the last counter reset."
    ::= { coiFcPmHistoryEntry 3 }

coiFcPmHistoryRxTotalPkts OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of receive packets."
    ::= { coiFcPmHistoryEntry 4 }

coiFcPmHistoryIfInErrors OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of receive errors."
    ::= { coiFcPmHistoryEntry 5 }

coiFcPmHistoryRxBadFcs OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of received frames with bad FCS, no coding error."
    ::= { coiFcPmHistoryEntry 6 }

coiFcPmHistoryRxFramesTooShort OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of truncated received frames."
    ::= { coiFcPmHistoryEntry 7 }

coiFcPmHistoryRxFramesTooLong OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of too long received frames."
    ::= { coiFcPmHistoryEntry 8 }

coiFcPmHistoryIfOutOctets OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of octets transmitted out of the interface,
         including framing characters."
    ::= { coiFcPmHistoryEntry 9 }

coiFcPmHistoryTxTotalPkts OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of transmitted packets."
    ::= { coiFcPmHistoryEntry 10 }

coiFcPmHistoryTxBadFcs OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of transmitted frames with bad FCS, no coding error."
    ::= { coiFcPmHistoryEntry 11 }

coiFcPmHistoryTxFramesTooShort OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of truncated transmitted frames."
    ::= { coiFcPmHistoryEntry 12 }

coiFcPmHistoryTxFramesTooLong OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of too long transmitted frames."
    ::= { coiFcPmHistoryEntry 13 }

coiFcPmHistoryValidData OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This variable indicates if the Fibre Channel layer performance monitoring data for the
         interval identified by coiFcPmHistoryIntervalType is valid."
    ::= { coiFcPmHistoryEntry 14 }


coiPcsPmCurrentTable OBJECT IDENTIFIER
    ::= { coiPcsPm 1 }

coiPcsPmCurrentEntry OBJECT-TYPE
    SYNTAX          CoiPcsPmCurrentEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "An entry containing PCS layer performance monitoring current interval data
        for Fibre Channel Controller."
    INDEX           {
                        ifIndex,
                        coiPcsPmCurrentIntervalType
                    }
    ::= { coiPcsPmCurrentTable 1 }
    
CoiPcsPmCurrentEntry ::= SEQUENCE {
        coiPcsPmCurrentIntervalType      CoiIntervalType,
        coiPcsPmCumBip                      Counter64,
        coiPcsPmCumFrmError                 Counter64,
        coiPcsPmCumBadSh                    Counter64,
        coiPcsPmEs                       Counter64,
        coiPcsPmSes                      Counter64,
        coiPcsPmUas                      Counter64,
        coiPcsPmFarEndEs                     Counter64,
        coiPcsPmFarEndSes                    Counter64,
        coiPcsPmFarEndUas                    Counter64,
        coiPcsCurrentPmValidData         TruthValue
}

coiPcsPmCurrentIntervalType OBJECT-TYPE
    SYNTAX          CoiIntervalType
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the interval type for which PCS layer
         current performance monitoring data is collected."
    ::= { coiPcsPmCurrentEntry 1 }

coiPcsPmCumBip OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the cumulative number of BIP errors."
    ::= { coiPcsPmCurrentEntry 2 }

coiPcsPmCumFrmError OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the cumulative number of frame errors."
    ::= { coiPcsPmCurrentEntry 3 }

coiPcsPmCumBadSh OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the cumulative number of bad sync header errors."
    ::= { coiPcsPmCurrentEntry 4 }

coiPcsPmEs OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of errored seconds."
    ::= { coiPcsPmCurrentEntry 5 }

coiPcsPmSes OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of severely errored seconds."
    ::= { coiPcsPmCurrentEntry 6 }

coiPcsPmUas OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of unavailable seconds."
    ::= { coiPcsPmCurrentEntry 7 }

coiPcsPmFarEndEs OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of errored seconds on the far end."
    ::= { coiPcsPmCurrentEntry 8 }

coiPcsPmFarEndSes OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of severely errored seconds on the far end."
    ::= { coiPcsPmCurrentEntry 9 }

coiPcsPmFarEndUas OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of unavailable seconds on the far end."
    ::= { coiPcsPmCurrentEntry 10 }

coiPcsCurrentPmValidData OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This variable indicates if the PCS layer performance monitoring data for the
         interval identified by coiPcsPmCurrentIntervalType is valid."
    ::= { coiPcsPmCurrentEntry 11 }

coiPcsPmHistoryTable OBJECT IDENTIFIER
    ::= { coiPcsPm 2 }

coiPcsPmHistoryEntry OBJECT-TYPE
    SYNTAX          CoiPcsPmHistoryEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "An entry containing PCS layer performance monitoring historical interval data
        for Fibre Channel Controller."
    INDEX           { 
                        ifIndex,
                        coiPcsPmHistoryIntervalType,
                        coiPcsPmIntervalNumber
                    }
    ::= { coiPcsPmHistoryTable 1 }

CoiPcsPmHistoryEntry ::= SEQUENCE {
        coiPcsPmHistoryIntervalType             CoiIntervalType,
        coiPcsPmIntervalNumber                    Unsigned32,
        coiPcsPmHistoryCumBip                      Counter64,
        coiPcsPmHistoryCumFrmError                 Counter64,
        coiPcsPmHistoryCumBadSh                    Counter64,
        coiPcsPmHistoryEs                       Counter64,
        coiPcsPmHistorySes                      Counter64,
        coiPcsPmHistoryUas                      Counter64,
        coiPcsPmHistoryEsFe                     Counter64,
        coiPcsPmHistorySesFe                    Counter64,
        coiPcsPmHistoryUasFe                    Counter64,
        coiPcsPmHistoryValidData                TruthValue
}

coiPcsPmHistoryIntervalType OBJECT-TYPE
    SYNTAX          CoiIntervalType
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the interval type for which PCS layer
         historical performance monitoring data is collected."
    ::= { coiPcsPmHistoryEntry 1 }

coiPcsPmIntervalNumber OBJECT-TYPE
    SYNTAX          Unsigned32 (1..32)
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "This object gives the interval number for PCS layer
         performance monitoring data in given interval."
    ::= { coiPcsPmHistoryEntry 2 }

coiPcsPmHistoryCumBip OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the cumulative number of BIP errors."
    ::= { coiPcsPmHistoryEntry 3 }

coiPcsPmHistoryCumFrmError OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the cumulative number of frame errors."
    ::= { coiPcsPmHistoryEntry 4 }

coiPcsPmHistoryCumBadSh OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the cumulative number of bad sync header errors."
    ::= { coiPcsPmHistoryEntry 5 }

coiPcsPmHistoryEs OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of errored seconds."
    ::= { coiPcsPmHistoryEntry 6 }

coiPcsPmHistorySes OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of severely errored seconds."
    ::= { coiPcsPmHistoryEntry 7 }

coiPcsPmHistoryUas OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of unavailable seconds."
    ::= { coiPcsPmHistoryEntry 8 }

coiPcsPmHistoryEsFe OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of errored seconds on the far end."
    ::= { coiPcsPmHistoryEntry 9 }

coiPcsPmHistorySesFe OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of severely errored seconds on the far end."
    ::= { coiPcsPmHistoryEntry 10 }

coiPcsPmHistoryUasFe OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of unavailable seconds on the far end."
    ::= { coiPcsPmHistoryEntry 11 }

coiPcsPmHistoryValidData OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This variable indicates if the PCS layer performance monitoring data for the
         interval identified by coiPcsPmHistoryIntervalType is valid."
    ::= { coiPcsPmHistoryEntry 12 }


coiFecPmCurrentTable OBJECT IDENTIFIER
    ::= { coiFecPm 1 }

coiFecPmCurrentEntry OBJECT-TYPE
    SYNTAX          CoiFecPmCurrentEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "An entry containing FEC layer performance monitoring current interval data
        for Fibre Channel Controller."
    INDEX           {
                        ifIndex,
                        coiFecPmCurrentIntervalType
                    }
    ::= { coiFecPmCurrentTable 1 }
    
CoiFecPmCurrentEntry ::= SEQUENCE {
        coiFecPmCurrentIntervalType      CoiIntervalType,
        coiFecPmCorWordErrs              Counter64,
        coiFecPmUncorWords               Counter64,
        coiFecPmPreFECMin                DisplayString,
        coiFecPmPreFECMax                DisplayString,
        coiFecPmPreFECAvg                DisplayString,
        coiFecPmPostFECMin               DisplayString,
        coiFecPmPostFECMax               DisplayString,
        coiFecPmPostFECAvg               DisplayString,
        coiFecPmQFactorMin               DisplayString,
        coiFecPmQFactorMax               DisplayString,
        coiFecPmQFactorAvg               DisplayString,
        coiFecPmQMarginMin               DisplayString,
        coiFecPmQMarginMax               DisplayString,
        coiFecPmQMarginAvg               DisplayString,
        coiFecPmInstQMarginMin           DisplayString,
        coiFecPmInstQMarginMax           DisplayString,
        coiFecPmInstQMarginAvg           DisplayString,
        coiFecCurrentPmValidData         TruthValue
}

coiFecPmCurrentIntervalType OBJECT-TYPE
    SYNTAX          CoiIntervalType
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the interval type for which FEC layer
         current performance monitoring data is collected."
    ::= { coiFecPmCurrentEntry 1 }

coiFecPmCorWordErrs OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of corrected word errors."
    ::= { coiFecPmCurrentEntry 2 }

coiFecPmUncorWords OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of number of uncorrectable words encountered."
    ::= { coiFecPmCurrentEntry 3 }

coiFecPmPreFECMin OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the minimum value of PreFEC BER."
    ::= { coiFecPmCurrentEntry 4 }

coiFecPmPreFECMax OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the maximum value of PreFEC BER."
    ::= { coiFecPmCurrentEntry 5 }

coiFecPmPreFECAvg OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the average value of PreFEC BER."
    ::= { coiFecPmCurrentEntry 6 }

coiFecPmPostFECMin OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the minimum value of PostFEC BER."
    ::= { coiFecPmCurrentEntry 7 }

coiFecPmPostFECMax OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the maximum value of PostFEC BER."
    ::= { coiFecPmCurrentEntry 8 }

coiFecPmPostFECAvg OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the average value of PostFEC BER."
    ::= { coiFecPmCurrentEntry 9 }

coiFecPmQFactorMin OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the minimum value of Q Factor."
    ::= { coiFecPmCurrentEntry 10 }

coiFecPmQFactorMax OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the maximum value of Q Factor."
    ::= { coiFecPmCurrentEntry 11 }

coiFecPmQFactorAvg OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the average value of Q Factor."
    ::= { coiFecPmCurrentEntry 12 }

coiFecPmQMarginMin OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the minimum value of Q Margin."
    ::= { coiFecPmCurrentEntry 13 }

coiFecPmQMarginMax OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the maximum value of Q Margin."
    ::= { coiFecPmCurrentEntry 14 }

coiFecPmQMarginAvg OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the average value of Q Margin."
    ::= { coiFecPmCurrentEntry 15 }

coiFecPmInstQMarginMin OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the minimum value of Instantaneous Q Margin."
    ::= { coiFecPmCurrentEntry 16 }

coiFecPmInstQMarginMax OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the maximum value of Instantaneous Q Margin."
    ::= { coiFecPmCurrentEntry 17 }

coiFecPmInstQMarginAvg OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the average value of Instantaneous Q Margin."
    ::= { coiFecPmCurrentEntry 18 }

coiFecCurrentPmValidData OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This variable indicates if the FEC layer performance monitoring data for the
         interval identified by coiFecPmCurrentIntervalType is valid."
    ::= { coiFecPmCurrentEntry 19 }

coiFecPmHistoryTable OBJECT IDENTIFIER
    ::= { coiFecPm 2 }

coiFecPmHistoryEntry OBJECT-TYPE
    SYNTAX          CoiFecPmHistoryEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "An entry containing FEC layer performance monitoring historical interval data
        for Fibre Channel Controller."
    INDEX           { 
                        ifIndex,
                        coiFecPmHistoryIntervalType,
                        coiFecPmIntervalNumber
                    }
    ::= { coiFecPmHistoryTable 1 }
    
CoiFecPmHistoryEntry ::= SEQUENCE {
        coiFecPmHistoryIntervalType             CoiIntervalType,
        coiFecPmIntervalNumber                    Unsigned32,
        coiFecPmHistoryCorWordErrs              Counter64,
        coiFecPmHistoryUncorWords               Counter64,
        coiFecPmHistoryPreFECMin                DisplayString,
        coiFecPmHistoryPreFECMax                DisplayString,
        coiFecPmHistoryPreFECAvg                DisplayString,
        coiFecPmHistoryPostFECMin               DisplayString,
        coiFecPmHistoryPostFECMax               DisplayString,
        coiFecPmHistoryPostFECAvg               DisplayString,
        coiFecPmHistoryQFactorMin               DisplayString,
        coiFecPmHistoryQFactorMax               DisplayString,
        coiFecPmHistoryQFactorAvg               DisplayString,
        coiFecPmHistoryQMarginMin               DisplayString,
        coiFecPmHistoryQMarginMax               DisplayString,
        coiFecPmHistoryQMarginAvg               DisplayString,
        coiFecPmHistoryInstQMarginMin           DisplayString,
        coiFecPmHistoryInstQMarginMax           DisplayString,
        coiFecPmHistoryInstQMarginAvg           DisplayString,
        coiFecPmHistoryValidData                TruthValue
}

coiFecPmHistoryIntervalType OBJECT-TYPE
    SYNTAX          CoiIntervalType
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the interval type for which FEC layer
         historical performance monitoring data is collected."
    ::= { coiFecPmHistoryEntry 1 }

coiFecPmIntervalNumber OBJECT-TYPE
    SYNTAX          Unsigned32 (1..32)
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "This object gives the interval number for FEC layer
         performance monitoring data in given interval."
    ::= { coiFecPmHistoryEntry 2 }

coiFecPmHistoryCorWordErrs OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of corrected word errors."
    ::= { coiFecPmHistoryEntry 3 }

coiFecPmHistoryUncorWords OBJECT-TYPE
    SYNTAX          Counter64
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the number of number of uncorrectable words encountered."
    ::= { coiFecPmHistoryEntry 4 }

coiFecPmHistoryPreFECMin OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the minimum value of PreFEC BER."
    ::= { coiFecPmHistoryEntry 5 }

coiFecPmHistoryPreFECMax OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the maximum value of PreFEC BER."
    ::= { coiFecPmHistoryEntry 6 }

coiFecPmHistoryPreFECAvg OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the average value of PreFEC BER."
    ::= { coiFecPmHistoryEntry 7 }

coiFecPmHistoryPostFECMin OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the minimum value of PostFEC BER."
    ::= { coiFecPmHistoryEntry 8 }

coiFecPmHistoryPostFECMax OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the maximum value of PostFEC BER."
    ::= { coiFecPmHistoryEntry 9 }

coiFecPmHistoryPostFECAvg OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the average value of PostFEC BER."
    ::= { coiFecPmHistoryEntry 10 }

coiFecPmHistoryQFactorMin OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the minimum value of Q Factor."
    ::= { coiFecPmHistoryEntry 11 }

coiFecPmHistoryQFactorMax OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the maximum value of Q Factor."
    ::= { coiFecPmHistoryEntry 12 }

coiFecPmHistoryQFactorAvg OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the average value of Q Factor."
    ::= { coiFecPmHistoryEntry 13 }

coiFecPmHistoryQMarginMin OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the minimum value of Q Margin."
    ::= { coiFecPmHistoryEntry 14 }

coiFecPmHistoryQMarginMax OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the maximum value of Q Margin."
    ::= { coiFecPmHistoryEntry 15 }

coiFecPmHistoryQMarginAvg OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the average value of Q Margin."
    ::= { coiFecPmHistoryEntry 16 }

coiFecPmHistoryInstQMarginMin OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the minimum value of Instantaneous Q Margin."
    ::= { coiFecPmHistoryEntry 17 }

coiFecPmHistoryInstQMarginMax OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the maximum value of Instantaneous Q Margin."
    ::= { coiFecPmHistoryEntry 18 }

coiFecPmHistoryInstQMarginAvg OBJECT-TYPE
    SYNTAX          DisplayString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object gives the average value of Instantaneous Q Margin."
    ::= { coiFecPmHistoryEntry 19 }

coiFecPmHistoryValidData OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This variable indicates if the FEC layer performance monitoring data for the
         interval identified by coiFecPmHistoryIntervalType is valid."
    ::= { coiFecPmHistoryEntry 20 }


-- MIB Conformance Statements

ciscoFibreChanMIBConformance  OBJECT IDENTIFIER
    ::= { ciscoFibreChanMIB 2 }

ciscoFibreChanMIBCompliances  OBJECT IDENTIFIER
    ::= { ciscoFibreChanMIBConformance 1 }

ciscoFibreChanMIBGroups  OBJECT IDENTIFIER
    ::= { ciscoFibreChanMIBConformance 2 }


END