-- ***************************************************************** -- PORT-MIB: Cisco private MIB -- **************************************************************** CIE1000-PORT-MIB DEFINITIONS ::= BEGIN IMPORTS NOTIFICATION-GROUP, MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF NOTIFICATION-TYPE, MODULE-IDENTITY, OBJECT-TYPE FROM SNMPv2-SMI TEXTUAL-CONVENTION FROM SNMPv2-TC cie1000SwitchMgmt FROM CISCO-IE1000-MIB CIE1000DisplayString FROM CIE1000-TC CIE1000InterfaceIndex FROM CIE1000-TC CIE1000PortStatusSpeed FROM CIE1000-TC CIE1000SfpTransceiver FROM CIE1000-TC CIE1000Unsigned8 FROM CIE1000-TC Counter64 FROM SNMPv2-SMI Integer32 FROM SNMPv2-SMI Unsigned32 FROM SNMPv2-SMI TruthValue FROM SNMPv2-TC ; cie1000PortMib MODULE-IDENTITY LAST-UPDATED "201507070000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 West Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-snmp@cisco.com" DESCRIPTION "This is a private version of the PORT MIB" REVISION "201507070000Z" DESCRIPTION "Port speed is moved into the TC MIB" REVISION "201407010000Z" DESCRIPTION "Initial version" ::= { cie1000SwitchMgmt 11 } CIE1000PortFc ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This enumeration controls the interface flow control." SYNTAX INTEGER { off(0), on(1) } CIE1000PortMedia ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This enumeration controls the interface media type." SYNTAX INTEGER { rj45(0), sfp(1), dual(2) } CIE1000PortPhyVeriPhyStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This enumerations show the VeriPhy status." SYNTAX INTEGER { correctlyTerminatedPair(0), openPair(1), shortPair(2), abnormalTermination(4), crossPairShortToPairA(8), crossPairShortToPairB(9), crossPairShortToPairC(10), crossPairShortToPairD(11), abnormalCrossPairCouplingToPairA(12), abnormalCrossPairCouplingToPairB(13), abnormalCrossPairCouplingToPairC(14), abnormalCrossPairCouplingToPairD(15), unknownResult(16), veriPhyRunning(17) } CIE1000PortSpeed ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This enumeration controls the interface speed. E.g force10ModeFdx means force 10Mbs full duplex." SYNTAX INTEGER { force10ModeFdx(0), force10ModeHdx(1), force100ModeFdx(2), force100ModeHdx(3), force1GModeFdx(4), autoNegMode(5), force2G5ModeFdx(6), force5GModeFdx(7), force10GModeFdx(8), force12GModeFdx(9) } cie1000PortMibObjects OBJECT IDENTIFIER ::= { cie1000PortMib 1 } cie1000PortConfig OBJECT IDENTIFIER ::= { cie1000PortMibObjects 2 } cie1000PortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000PortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is a table of the port interface parameters" ::= { cie1000PortConfig 1 } cie1000PortConfigEntry OBJECT-TYPE SYNTAX CIE1000PortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each port interface has a set of parameters" INDEX { cie1000PortConfigIfIndex } ::= { cie1000PortConfigTable 1 } CIE1000PortConfigEntry ::= SEQUENCE { cie1000PortConfigIfIndex CIE1000InterfaceIndex, cie1000PortConfigShutdown TruthValue, cie1000PortConfigSpeed CIE1000PortSpeed, cie1000PortConfigAdvertiseDisabled CIE1000Unsigned8, cie1000PortConfigMediaType CIE1000PortMedia, cie1000PortConfigFC CIE1000PortFc, cie1000PortConfigMTU Unsigned32, cie1000PortConfigExcessiveRestart TruthValue, cie1000PortConfigPFC CIE1000Unsigned8, cie1000PortConfigFrameLengthCheck TruthValue } cie1000PortConfigIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number." ::= { cie1000PortConfigEntry 1 } cie1000PortConfigShutdown OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Controls whether interface is shutdown or powered up. Set to TRUE in order to power down the interface." ::= { cie1000PortConfigEntry 2 } cie1000PortConfigSpeed OBJECT-TYPE SYNTAX CIE1000PortSpeed MAX-ACCESS read-write STATUS current DESCRIPTION "Controls the port speed and duplex." ::= { cie1000PortConfigEntry 3 } cie1000PortConfigAdvertiseDisabled OBJECT-TYPE SYNTAX CIE1000Unsigned8 MAX-ACCESS read-write STATUS current DESCRIPTION "In auto mode, bitmask that allows features not to be advertised. Bit 0: Disable half duplex advertising. Bit 1: Disable full duplex advertising. Bit 4: Disable 1G advertising. Bit 6: Disable 100M advertising. Bit 7: Disable 10M advertising. When not in auto mode, the value shall be zero." ::= { cie1000PortConfigEntry 4 } cie1000PortConfigMediaType OBJECT-TYPE SYNTAX CIE1000PortMedia MAX-ACCESS read-write STATUS current DESCRIPTION "Controls the port media type." ::= { cie1000PortConfigEntry 5 } cie1000PortConfigFC OBJECT-TYPE SYNTAX CIE1000PortFc MAX-ACCESS read-write STATUS current DESCRIPTION "Controls the port flow control mode." ::= { cie1000PortConfigEntry 6 } cie1000PortConfigMTU OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Controls the port's Maximum Transmission Unit." ::= { cie1000PortConfigEntry 7 } cie1000PortConfigExcessiveRestart OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "TRUE to restart half-duplex back-off algorithm after 16 collisions. FALSE to discard frame after 16 collisions" ::= { cie1000PortConfigEntry 8 } cie1000PortConfigPFC OBJECT-TYPE SYNTAX CIE1000Unsigned8 MAX-ACCESS read-write STATUS current DESCRIPTION "802.1Qbb Priority Flow Control bitmask, one bit for each prioritet.E.g. 0x01 = prio 0, 0x80 = prio 7, 0xFF = prio 0-7" ::= { cie1000PortConfigEntry 9 } cie1000PortConfigFrameLengthCheck OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "TRUE to enforce 802.3 frame length check (from Ethertype field). If enabled frames with length that doesn't match the frame length field will be dropped." ::= { cie1000PortConfigEntry 10 } cie1000PortStatus OBJECT IDENTIFIER ::= { cie1000PortMibObjects 3 } cie1000PortStatusInformationTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000PortStatusInformationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the status of the ports" ::= { cie1000PortStatus 1 } cie1000PortStatusInformationEntry OBJECT-TYPE SYNTAX CIE1000PortStatusInformationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each port interface has a set of status parameters" INDEX { cie1000PortStatusInformationIfIndex } ::= { cie1000PortStatusInformationTable 1 } CIE1000PortStatusInformationEntry ::= SEQUENCE { cie1000PortStatusInformationIfIndex CIE1000InterfaceIndex, cie1000PortStatusInformationLink TruthValue, cie1000PortStatusInformationFdx TruthValue, cie1000PortStatusInformationFiber TruthValue, cie1000PortStatusInformationSpeed CIE1000PortStatusSpeed, cie1000PortStatusInformationSFPType CIE1000SfpTransceiver, cie1000PortStatusInformationSFPVendorName CIE1000DisplayString, cie1000PortStatusInformationSFPVendorPN CIE1000DisplayString, cie1000PortStatusInformationSFPVendorRev CIE1000DisplayString, cie1000PortStatusInformationSFPVendorSN CIE1000DisplayString, cie1000PortStatusInformationRxUtilization Unsigned32, cie1000PortStatusInformationTxUtilization Unsigned32, cie1000PortStatusInformationRxErrorUtilization Unsigned32, cie1000PortStatusInformationTxErrorUtilization Unsigned32 } cie1000PortStatusInformationIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number." ::= { cie1000PortStatusInformationEntry 1 } cie1000PortStatusInformationLink OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Shows whether interface has link." ::= { cie1000PortStatusInformationEntry 2 } cie1000PortStatusInformationFdx OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Shows whether interface is running in full duplex." ::= { cie1000PortStatusInformationEntry 3 } cie1000PortStatusInformationFiber OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Shows whether interface is a fiber link (fiber SFP or cu SFP)." ::= { cie1000PortStatusInformationEntry 4 } cie1000PortStatusInformationSpeed OBJECT-TYPE SYNTAX CIE1000PortStatusSpeed MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the current interface speed." ::= { cie1000PortStatusInformationEntry 5 } cie1000PortStatusInformationSFPType OBJECT-TYPE SYNTAX CIE1000SfpTransceiver MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the current interface SFP type." ::= { cie1000PortStatusInformationEntry 6 } cie1000PortStatusInformationSFPVendorName OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..19)) MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the SFP vendor name." ::= { cie1000PortStatusInformationEntry 7 } cie1000PortStatusInformationSFPVendorPN OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..19)) MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the SFP vendor Product Number." ::= { cie1000PortStatusInformationEntry 8 } cie1000PortStatusInformationSFPVendorRev OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..5)) MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the SFP vendor Revision." ::= { cie1000PortStatusInformationEntry 9 } cie1000PortStatusInformationSFPVendorSN OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..19)) MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the SFP vendor Serial Number." ::= { cie1000PortStatusInformationEntry 10 } cie1000PortStatusInformationRxUtilization OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Rx utilization in percent." ::= { cie1000PortStatusInformationEntry 11 } cie1000PortStatusInformationTxUtilization OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Tx utilization in percent." ::= { cie1000PortStatusInformationEntry 12 } cie1000PortStatusInformationRxErrorUtilization OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Rx error utilization in percent." ::= { cie1000PortStatusInformationEntry 13 } cie1000PortStatusInformationTxErrorUtilization OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Tx error utilization in percent." ::= { cie1000PortStatusInformationEntry 14 } cie1000PortStatusVeriPhyResult OBJECT IDENTIFIER ::= { cie1000PortStatus 3 } cie1000PortStatusVeriPhyResultTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000PortStatusVeriPhyResultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the VeriPhy result from the last VeriPhy run for the interface" ::= { cie1000PortStatusVeriPhyResult 1 } cie1000PortStatusVeriPhyResultEntry OBJECT-TYPE SYNTAX CIE1000PortStatusVeriPhyResultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each port has a set of VeriPhy results" INDEX { cie1000PortStatusVeriPhyResultIfIndex } ::= { cie1000PortStatusVeriPhyResultTable 1 } CIE1000PortStatusVeriPhyResultEntry ::= SEQUENCE { cie1000PortStatusVeriPhyResultIfIndex CIE1000InterfaceIndex, cie1000PortStatusVeriPhyResultVeriPhyStatusPairA CIE1000PortPhyVeriPhyStatus, cie1000PortStatusVeriPhyResultVeriPhyStatusPairB CIE1000PortPhyVeriPhyStatus, cie1000PortStatusVeriPhyResultVeriPhyStatusPairC CIE1000PortPhyVeriPhyStatus, cie1000PortStatusVeriPhyResultVeriPhyStatusPairD CIE1000PortPhyVeriPhyStatus, cie1000PortStatusVeriPhyResultVeriPhyLengthStatusPairA CIE1000Unsigned8, cie1000PortStatusVeriPhyResultVeriPhyLengthStatusPairB CIE1000Unsigned8, cie1000PortStatusVeriPhyResultVeriPhyLengthStatusPairC CIE1000Unsigned8, cie1000PortStatusVeriPhyResultVeriPhyLengthStatusPairD CIE1000Unsigned8 } cie1000PortStatusVeriPhyResultIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number." ::= { cie1000PortStatusVeriPhyResultEntry 1 } cie1000PortStatusVeriPhyResultVeriPhyStatusPairA OBJECT-TYPE SYNTAX CIE1000PortPhyVeriPhyStatus MAX-ACCESS read-only STATUS current DESCRIPTION "VeriPhy status for the cable pair 0 - Cable is Correctly terminated pair 1 - Open pair 2 - Shorted pair 4 - Abnormal termination 8 - Cross-pair short to pair A 9 - Cross-pair short to pair B 10 - Cross-pair short to pair C 11 - Cross-pair short to pair D 12 - Abnormal cross-pair coupling - pair A 13 - Abnormal cross-pair coupling - pair B 14 - Abnormal cross-pair coupling - pair C 15 - Abnormal cross-pair coupling - pair D" ::= { cie1000PortStatusVeriPhyResultEntry 2 } cie1000PortStatusVeriPhyResultVeriPhyStatusPairB OBJECT-TYPE SYNTAX CIE1000PortPhyVeriPhyStatus MAX-ACCESS read-only STATUS current DESCRIPTION "VeriPhy status for the cable pair 0 - Cable is Correctly terminated pair 1 - Open pair 2 - Shorted pair 4 - Abnormal termination 8 - Cross-pair short to pair A 9 - Cross-pair short to pair B 10 - Cross-pair short to pair C 11 - Cross-pair short to pair D 12 - Abnormal cross-pair coupling - pair A 13 - Abnormal cross-pair coupling - pair B 14 - Abnormal cross-pair coupling - pair C 15 - Abnormal cross-pair coupling - pair D" ::= { cie1000PortStatusVeriPhyResultEntry 3 } cie1000PortStatusVeriPhyResultVeriPhyStatusPairC OBJECT-TYPE SYNTAX CIE1000PortPhyVeriPhyStatus MAX-ACCESS read-only STATUS current DESCRIPTION "VeriPhy status for the cable pair 0 - Cable is Correctly terminated pair 1 - Open pair 2 - Shorted pair 4 - Abnormal termination 8 - Cross-pair short to pair A 9 - Cross-pair short to pair B 10 - Cross-pair short to pair C 11 - Cross-pair short to pair D 12 - Abnormal cross-pair coupling - pair A 13 - Abnormal cross-pair coupling - pair B 14 - Abnormal cross-pair coupling - pair C 15 - Abnormal cross-pair coupling - pair D" ::= { cie1000PortStatusVeriPhyResultEntry 4 } cie1000PortStatusVeriPhyResultVeriPhyStatusPairD OBJECT-TYPE SYNTAX CIE1000PortPhyVeriPhyStatus MAX-ACCESS read-only STATUS current DESCRIPTION "VeriPhy status for the cable pair 0 - Cable is Correctly terminated pair 1 - Open pair 2 - Shorted pair 4 - Abnormal termination 8 - Cross-pair short to pair A 9 - Cross-pair short to pair B 10 - Cross-pair short to pair C 11 - Cross-pair short to pair D 12 - Abnormal cross-pair coupling - pair A 13 - Abnormal cross-pair coupling - pair B 14 - Abnormal cross-pair coupling - pair C 15 - Abnormal cross-pair coupling - pair D" ::= { cie1000PortStatusVeriPhyResultEntry 5 } cie1000PortStatusVeriPhyResultVeriPhyLengthStatusPairA OBJECT-TYPE SYNTAX CIE1000Unsigned8 MAX-ACCESS read-only STATUS current DESCRIPTION "VeriPhy status cable length i meters for the cable pair. When VeriPhy is completed, the cable diagnostics results is shown in the VeriPhy status table. Note that VeriPHY is only accurate for cables of length 7 - 140 meters. The resolution is 3 meters" ::= { cie1000PortStatusVeriPhyResultEntry 6 } cie1000PortStatusVeriPhyResultVeriPhyLengthStatusPairB OBJECT-TYPE SYNTAX CIE1000Unsigned8 MAX-ACCESS read-only STATUS current DESCRIPTION "VeriPhy status cable length i meters for the cable pair. When VeriPhy is completed, the cable diagnostics results is shown in the VeriPhy status table. Note that VeriPHY is only accurate for cables of length 7 - 140 meters. The resolution is 3 meters" ::= { cie1000PortStatusVeriPhyResultEntry 7 } cie1000PortStatusVeriPhyResultVeriPhyLengthStatusPairC OBJECT-TYPE SYNTAX CIE1000Unsigned8 MAX-ACCESS read-only STATUS current DESCRIPTION "VeriPhy status cable length i meters for the cable pair. When VeriPhy is completed, the cable diagnostics results is shown in the VeriPhy status table. Note that VeriPHY is only accurate for cables of length 7 - 140 meters. The resolution is 3 meters" ::= { cie1000PortStatusVeriPhyResultEntry 8 } cie1000PortStatusVeriPhyResultVeriPhyLengthStatusPairD OBJECT-TYPE SYNTAX CIE1000Unsigned8 MAX-ACCESS read-only STATUS current DESCRIPTION "VeriPhy status cable length i meters for the cable pair. When VeriPhy is completed, the cable diagnostics results is shown in the VeriPhy status table. Note that VeriPHY is only accurate for cables of length 7 - 140 meters. The resolution is 3 meters" ::= { cie1000PortStatusVeriPhyResultEntry 9 } cie1000PortControl OBJECT IDENTIFIER ::= { cie1000PortMibObjects 4 } cie1000PortControlStatisticsClear OBJECT IDENTIFIER ::= { cie1000PortControl 1 } cie1000PortControlStatisticsClearTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000PortControlStatisticsClearEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is a table to clear port Interface statistics" ::= { cie1000PortControlStatisticsClear 1 } cie1000PortControlStatisticsClearEntry OBJECT-TYPE SYNTAX CIE1000PortControlStatisticsClearEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each port has a set of control parameters" INDEX { cie1000PortControlStatisticsClearIfIndex } ::= { cie1000PortControlStatisticsClearTable 1 } CIE1000PortControlStatisticsClearEntry ::= SEQUENCE { cie1000PortControlStatisticsClearIfIndex CIE1000InterfaceIndex, cie1000PortControlStatisticsClearStatisticsClear TruthValue } cie1000PortControlStatisticsClearIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number." ::= { cie1000PortControlStatisticsClearEntry 1 } cie1000PortControlStatisticsClearStatisticsClear OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Set to TRUE to clear the statistics of an interface." ::= { cie1000PortControlStatisticsClearEntry 2 } cie1000PortControlVeriPhyStart OBJECT IDENTIFIER ::= { cie1000PortControl 2 } cie1000PortControlVeriPhyStartTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000PortControlVeriPhyStartEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is a table to start VeriPhy for the interface" ::= { cie1000PortControlVeriPhyStart 1 } cie1000PortControlVeriPhyStartEntry OBJECT-TYPE SYNTAX CIE1000PortControlVeriPhyStartEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each port has a set of control parameters" INDEX { cie1000PortControlVeriPhyStartIfIndex } ::= { cie1000PortControlVeriPhyStartTable 1 } CIE1000PortControlVeriPhyStartEntry ::= SEQUENCE { cie1000PortControlVeriPhyStartIfIndex CIE1000InterfaceIndex, cie1000PortControlVeriPhyStartStart TruthValue } cie1000PortControlVeriPhyStartIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number." ::= { cie1000PortControlVeriPhyStartEntry 1 } cie1000PortControlVeriPhyStartStart OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Set to TRUE to start VeriPHy for the interface. When running 10 and 100 Mbps, ports will be linked down while running VeriPHY. Therefore, running VeriPHY on a 10 or 100 Mbps management port will cause the switch to stop responding until VeriPHY is complete." ::= { cie1000PortControlVeriPhyStartEntry 2 } cie1000PortStatistics OBJECT IDENTIFIER ::= { cie1000PortMibObjects 5 } cie1000PortStatisticsRmonStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000PortStatisticsRmonStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the port interface RMON statistics counters" ::= { cie1000PortStatistics 1 } cie1000PortStatisticsRmonStatisticsEntry OBJECT-TYPE SYNTAX CIE1000PortStatisticsRmonStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each port interface has a set of statistics counters" INDEX { cie1000PortStatisticsRmonStatisticsIfIndex } ::= { cie1000PortStatisticsRmonStatisticsTable 1 } CIE1000PortStatisticsRmonStatisticsEntry ::= SEQUENCE { cie1000PortStatisticsRmonStatisticsIfIndex CIE1000InterfaceIndex, cie1000PortStatisticsRmonStatisticsRxDropEvents Counter64, cie1000PortStatisticsRmonStatisticsRxOctets Counter64, cie1000PortStatisticsRmonStatisticsRxPkts Counter64, cie1000PortStatisticsRmonStatisticsRxBroadcastPkts Counter64, cie1000PortStatisticsRmonStatisticsRxMulticastPkts Counter64, cie1000PortStatisticsRmonStatisticsRxCrcAlignErrPkts Counter64, cie1000PortStatisticsRmonStatisticsRxUndersizePkts Counter64, cie1000PortStatisticsRmonStatisticsRxOversizePkts Counter64, cie1000PortStatisticsRmonStatisticsRxFragmentsPkts Counter64, cie1000PortStatisticsRmonStatisticsRxJabbersPkts Counter64, cie1000PortStatisticsRmonStatisticsRx64Pkts Counter64, cie1000PortStatisticsRmonStatisticsRx65to127Pkts Counter64, cie1000PortStatisticsRmonStatisticsRx128to255Pkts Counter64, cie1000PortStatisticsRmonStatisticsRx256to511Pkts Counter64, cie1000PortStatisticsRmonStatisticsRx512to1023Pkts Counter64, cie1000PortStatisticsRmonStatisticsRx1024to1518Pkts Counter64, cie1000PortStatisticsRmonStatisticsRx1519PktsToMax Counter64, cie1000PortStatisticsRmonStatisticsTxDropEvents Counter64, cie1000PortStatisticsRmonStatisticsTxOctets Counter64, cie1000PortStatisticsRmonStatisticsTxPkts Counter64, cie1000PortStatisticsRmonStatisticsTxBroadcastPkts Counter64, cie1000PortStatisticsRmonStatisticsTxMulticastPkts Counter64, cie1000PortStatisticsRmonStatisticsTx64Pkts Counter64, cie1000PortStatisticsRmonStatisticsTx65to127Pkts Counter64, cie1000PortStatisticsRmonStatisticsTx128to255Pkts Counter64, cie1000PortStatisticsRmonStatisticsTx256to511Pkts Counter64, cie1000PortStatisticsRmonStatisticsTx512to1023Pkts Counter64, cie1000PortStatisticsRmonStatisticsTx1024to1518Pkts Counter64, cie1000PortStatisticsRmonStatisticsTx1519PktsToMax Counter64 } cie1000PortStatisticsRmonStatisticsIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number." ::= { cie1000PortStatisticsRmonStatisticsEntry 1 } cie1000PortStatisticsRmonStatisticsRxDropEvents OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of frames discarded due to ingress congestion." ::= { cie1000PortStatisticsRmonStatisticsEntry 2 } cie1000PortStatisticsRmonStatisticsRxOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of received (good and bad) bytes. Includes FCS, but excludes framing bits." ::= { cie1000PortStatisticsRmonStatisticsEntry 3 } cie1000PortStatisticsRmonStatisticsRxPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of received (good and bad) packets." ::= { cie1000PortStatisticsRmonStatisticsEntry 4 } cie1000PortStatisticsRmonStatisticsRxBroadcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of received (good and bad) broadcast packets." ::= { cie1000PortStatisticsRmonStatisticsEntry 5 } cie1000PortStatisticsRmonStatisticsRxMulticastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of received (good and bad) multicast packets." ::= { cie1000PortStatisticsRmonStatisticsEntry 6 } cie1000PortStatisticsRmonStatisticsRxCrcAlignErrPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of frames received with CRC or alignment errors." ::= { cie1000PortStatisticsRmonStatisticsEntry 7 } cie1000PortStatisticsRmonStatisticsRxUndersizePkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of short frames (frames that are smaller than 64 bytes) received with valid CRC." ::= { cie1000PortStatisticsRmonStatisticsEntry 8 } cie1000PortStatisticsRmonStatisticsRxOversizePkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of long frames received with valid CRC." ::= { cie1000PortStatisticsRmonStatisticsEntry 9 } cie1000PortStatisticsRmonStatisticsRxFragmentsPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of short frames (frames that are smaller than 64 bytes) received with invalid CRC." ::= { cie1000PortStatisticsRmonStatisticsEntry 10 } cie1000PortStatisticsRmonStatisticsRxJabbersPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of long frames (frames that are longer than the configured maximum frame length for this interface) received with invalid CRC." ::= { cie1000PortStatisticsRmonStatisticsEntry 11 } cie1000PortStatisticsRmonStatisticsRx64Pkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of 64 bytes frames received." ::= { cie1000PortStatisticsRmonStatisticsEntry 12 } cie1000PortStatisticsRmonStatisticsRx65to127Pkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of received frames with size within 65 to 127 bytes." ::= { cie1000PortStatisticsRmonStatisticsEntry 13 } cie1000PortStatisticsRmonStatisticsRx128to255Pkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of received frames with size within 128 to 255 bytes." ::= { cie1000PortStatisticsRmonStatisticsEntry 14 } cie1000PortStatisticsRmonStatisticsRx256to511Pkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of received frames with size within 256 to 511 bytes." ::= { cie1000PortStatisticsRmonStatisticsEntry 15 } cie1000PortStatisticsRmonStatisticsRx512to1023Pkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of received frames with size within 512 to 1023 bytes." ::= { cie1000PortStatisticsRmonStatisticsEntry 16 } cie1000PortStatisticsRmonStatisticsRx1024to1518Pkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of received frames with size within 1024 to 1518 bytes." ::= { cie1000PortStatisticsRmonStatisticsEntry 17 } cie1000PortStatisticsRmonStatisticsRx1519PktsToMax OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of received frames with size larger than 1518 bytes." ::= { cie1000PortStatisticsRmonStatisticsEntry 18 } cie1000PortStatisticsRmonStatisticsTxDropEvents OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of frames discarded due to egress congestion." ::= { cie1000PortStatisticsRmonStatisticsEntry 19 } cie1000PortStatisticsRmonStatisticsTxOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of transmitted (good and bad) bytes. Includes FCS, but excludes framing bits." ::= { cie1000PortStatisticsRmonStatisticsEntry 20 } cie1000PortStatisticsRmonStatisticsTxPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of transmitted (good and bad) packets." ::= { cie1000PortStatisticsRmonStatisticsEntry 21 } cie1000PortStatisticsRmonStatisticsTxBroadcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of transmitted (good and bad) broadcast packets." ::= { cie1000PortStatisticsRmonStatisticsEntry 22 } cie1000PortStatisticsRmonStatisticsTxMulticastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of transmitted (good and bad) multicast packets." ::= { cie1000PortStatisticsRmonStatisticsEntry 23 } cie1000PortStatisticsRmonStatisticsTx64Pkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of 64 bytes frames transmitted." ::= { cie1000PortStatisticsRmonStatisticsEntry 24 } cie1000PortStatisticsRmonStatisticsTx65to127Pkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of transmitted frames with size within 65 to 127 bytes." ::= { cie1000PortStatisticsRmonStatisticsEntry 25 } cie1000PortStatisticsRmonStatisticsTx128to255Pkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of transmitted frames with size within 128 to 255 bytes." ::= { cie1000PortStatisticsRmonStatisticsEntry 26 } cie1000PortStatisticsRmonStatisticsTx256to511Pkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of transmitted frames with size within 256 to 511 bytes." ::= { cie1000PortStatisticsRmonStatisticsEntry 27 } cie1000PortStatisticsRmonStatisticsTx512to1023Pkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of transmitted frames with size within 512 to 1023 bytes." ::= { cie1000PortStatisticsRmonStatisticsEntry 28 } cie1000PortStatisticsRmonStatisticsTx1024to1518Pkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of transmitted frames with size within 1024 to 1518 bytes." ::= { cie1000PortStatisticsRmonStatisticsEntry 29 } cie1000PortStatisticsRmonStatisticsTx1519PktsToMax OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of transmitted frames with size larger than 1518 bytes." ::= { cie1000PortStatisticsRmonStatisticsEntry 30 } cie1000PortStatisticsIfGroupStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000PortStatisticsIfGroupStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the port interfaces group (RFC 2863) counters" ::= { cie1000PortStatistics 2 } cie1000PortStatisticsIfGroupStatisticsEntry OBJECT-TYPE SYNTAX CIE1000PortStatisticsIfGroupStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each port interface has a set of statistics counters" INDEX { cie1000PortStatisticsIfGroupStatisticsIfIndex } ::= { cie1000PortStatisticsIfGroupStatisticsTable 1 } CIE1000PortStatisticsIfGroupStatisticsEntry ::= SEQUENCE { cie1000PortStatisticsIfGroupStatisticsIfIndex CIE1000InterfaceIndex, cie1000PortStatisticsIfGroupStatisticsRxOctets Counter64, cie1000PortStatisticsIfGroupStatisticsRxUnicastPkts Counter64, cie1000PortStatisticsIfGroupStatisticsRxMulticastPkts Counter64, cie1000PortStatisticsIfGroupStatisticsRxBroadcastPkts Counter64, cie1000PortStatisticsIfGroupStatisticsRxNonUnicastPkts Counter64, cie1000PortStatisticsIfGroupStatisticsRxDiscards Counter64, cie1000PortStatisticsIfGroupStatisticsRxErrors Counter64, cie1000PortStatisticsIfGroupStatisticsTxOctets Counter64, cie1000PortStatisticsIfGroupStatisticsTxUnicastPkts Counter64, cie1000PortStatisticsIfGroupStatisticsTxMulticastPkts Counter64, cie1000PortStatisticsIfGroupStatisticsTxBroadcastPkts Counter64, cie1000PortStatisticsIfGroupStatisticsTxNonUnicastPkts Counter64, cie1000PortStatisticsIfGroupStatisticsTxDiscardPkts Counter64, cie1000PortStatisticsIfGroupStatisticsTxErrorPkts Counter64 } cie1000PortStatisticsIfGroupStatisticsIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number." ::= { cie1000PortStatisticsIfGroupStatisticsEntry 1 } cie1000PortStatisticsIfGroupStatisticsRxOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of bytes received." ::= { cie1000PortStatisticsIfGroupStatisticsEntry 2 } cie1000PortStatisticsIfGroupStatisticsRxUnicastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of uni-cast frames received." ::= { cie1000PortStatisticsIfGroupStatisticsEntry 3 } cie1000PortStatisticsIfGroupStatisticsRxMulticastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of multi-cast frames received." ::= { cie1000PortStatisticsIfGroupStatisticsEntry 4 } cie1000PortStatisticsIfGroupStatisticsRxBroadcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of broad-cast frames received." ::= { cie1000PortStatisticsIfGroupStatisticsEntry 5 } cie1000PortStatisticsIfGroupStatisticsRxNonUnicastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of non uni-cast frames received." ::= { cie1000PortStatisticsIfGroupStatisticsEntry 6 } cie1000PortStatisticsIfGroupStatisticsRxDiscards OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of received frames discarded." ::= { cie1000PortStatisticsIfGroupStatisticsEntry 7 } cie1000PortStatisticsIfGroupStatisticsRxErrors OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of frames with errors received." ::= { cie1000PortStatisticsIfGroupStatisticsEntry 8 } cie1000PortStatisticsIfGroupStatisticsTxOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of bytes transmitted." ::= { cie1000PortStatisticsIfGroupStatisticsEntry 9 } cie1000PortStatisticsIfGroupStatisticsTxUnicastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of uni-cast frames transmitted." ::= { cie1000PortStatisticsIfGroupStatisticsEntry 10 } cie1000PortStatisticsIfGroupStatisticsTxMulticastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of multi-cast frames transmitted." ::= { cie1000PortStatisticsIfGroupStatisticsEntry 11 } cie1000PortStatisticsIfGroupStatisticsTxBroadcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of broad-cast frames transmitted." ::= { cie1000PortStatisticsIfGroupStatisticsEntry 12 } cie1000PortStatisticsIfGroupStatisticsTxNonUnicastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of non uni-cast frames transmitted." ::= { cie1000PortStatisticsIfGroupStatisticsEntry 13 } cie1000PortStatisticsIfGroupStatisticsTxDiscardPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of discard frames which should been transmitted." ::= { cie1000PortStatisticsIfGroupStatisticsEntry 14 } cie1000PortStatisticsIfGroupStatisticsTxErrorPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of frames transmit with error." ::= { cie1000PortStatisticsIfGroupStatisticsEntry 15 } cie1000PortStatisticsEthernetLikeStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000PortStatisticsEthernetLikeStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the port Ethernet-like interfaces counters" ::= { cie1000PortStatistics 3 } cie1000PortStatisticsEthernetLikeStatisticsEntry OBJECT-TYPE SYNTAX CIE1000PortStatisticsEthernetLikeStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each port interface has a set of statistics counters" INDEX { cie1000PortStatisticsEthernetLikeStatisticsIfIndex } ::= { cie1000PortStatisticsEthernetLikeStatisticsTable 1 } CIE1000PortStatisticsEthernetLikeStatisticsEntry ::= SEQUENCE { cie1000PortStatisticsEthernetLikeStatisticsIfIndex CIE1000InterfaceIndex, cie1000PortStatisticsEthernetLikeStatisticsRxPauseFrames Counter64, cie1000PortStatisticsEthernetLikeStatisticsTxPauseFrames Counter64 } cie1000PortStatisticsEthernetLikeStatisticsIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number." ::= { cie1000PortStatisticsEthernetLikeStatisticsEntry 1 } cie1000PortStatisticsEthernetLikeStatisticsRxPauseFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pause frames received." ::= { cie1000PortStatisticsEthernetLikeStatisticsEntry 2 } cie1000PortStatisticsEthernetLikeStatisticsTxPauseFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pause frames transmitted." ::= { cie1000PortStatisticsEthernetLikeStatisticsEntry 3 } cie1000PortStatisticsQueuesStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000PortStatisticsQueuesStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the port interfaces queues counters" ::= { cie1000PortStatistics 4 } cie1000PortStatisticsQueuesStatisticsEntry OBJECT-TYPE SYNTAX CIE1000PortStatisticsQueuesStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each port interface has a set of statistics counters" INDEX { cie1000PortStatisticsQueuesStatisticsIfIndex, cie1000PortStatisticsQueuesStatisticsQueue } ::= { cie1000PortStatisticsQueuesStatisticsTable 1 } CIE1000PortStatisticsQueuesStatisticsEntry ::= SEQUENCE { cie1000PortStatisticsQueuesStatisticsIfIndex CIE1000InterfaceIndex, cie1000PortStatisticsQueuesStatisticsQueue Integer32, cie1000PortStatisticsQueuesStatisticsRxPrio Counter64, cie1000PortStatisticsQueuesStatisticsTxPrio Counter64 } cie1000PortStatisticsQueuesStatisticsIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number." ::= { cie1000PortStatisticsQueuesStatisticsEntry 1 } cie1000PortStatisticsQueuesStatisticsQueue OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Queue index." ::= { cie1000PortStatisticsQueuesStatisticsEntry 2 } cie1000PortStatisticsQueuesStatisticsRxPrio OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames received for the queue." ::= { cie1000PortStatisticsQueuesStatisticsEntry 3 } cie1000PortStatisticsQueuesStatisticsTxPrio OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames transmitted for the queue." ::= { cie1000PortStatisticsQueuesStatisticsEntry 4 } cie1000PortStatisticsBridgeStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000PortStatisticsBridgeStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the port interface bridge counters" ::= { cie1000PortStatistics 5 } cie1000PortStatisticsBridgeStatisticsEntry OBJECT-TYPE SYNTAX CIE1000PortStatisticsBridgeStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each port interface has a set of statistics counters" INDEX { cie1000PortStatisticsBridgeStatisticsIfIndex } ::= { cie1000PortStatisticsBridgeStatisticsTable 1 } CIE1000PortStatisticsBridgeStatisticsEntry ::= SEQUENCE { cie1000PortStatisticsBridgeStatisticsIfIndex CIE1000InterfaceIndex, cie1000PortStatisticsBridgeStatisticsRxBridgeDiscard Counter64 } cie1000PortStatisticsBridgeStatisticsIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number." ::= { cie1000PortStatisticsBridgeStatisticsEntry 1 } cie1000PortStatisticsBridgeStatisticsRxBridgeDiscard OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bridge frames discarded." ::= { cie1000PortStatisticsBridgeStatisticsEntry 2 } cie1000PortMibConformance OBJECT IDENTIFIER ::= { cie1000PortMib 2 } cie1000PortMibCompliances OBJECT IDENTIFIER ::= { cie1000PortMibConformance 1 } cie1000PortMibGroups OBJECT IDENTIFIER ::= { cie1000PortMibConformance 2 } cie1000PortConfigInfoGroup OBJECT-GROUP OBJECTS { cie1000PortConfigIfIndex, cie1000PortConfigShutdown, cie1000PortConfigSpeed, cie1000PortConfigAdvertiseDisabled, cie1000PortConfigMediaType, cie1000PortConfigFC, cie1000PortConfigMTU, cie1000PortConfigExcessiveRestart, cie1000PortConfigPFC, cie1000PortConfigFrameLengthCheck } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000PortMibGroups 1 } cie1000PortStatusInformationTableInfoGroup OBJECT-GROUP OBJECTS { cie1000PortStatusInformationIfIndex, cie1000PortStatusInformationLink, cie1000PortStatusInformationFdx, cie1000PortStatusInformationFiber, cie1000PortStatusInformationSpeed, cie1000PortStatusInformationSFPType, cie1000PortStatusInformationSFPVendorName, cie1000PortStatusInformationSFPVendorPN, cie1000PortStatusInformationSFPVendorRev, cie1000PortStatusInformationSFPVendorSN, cie1000PortStatusInformationRxUtilization, cie1000PortStatusInformationTxUtilization, cie1000PortStatusInformationRxErrorUtilization, cie1000PortStatusInformationTxErrorUtilization } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000PortMibGroups 2 } cie1000PortStatusVeriPhyResultTableInfoGroup OBJECT-GROUP OBJECTS { cie1000PortStatusVeriPhyResultIfIndex, cie1000PortStatusVeriPhyResultVeriPhyStatusPairA, cie1000PortStatusVeriPhyResultVeriPhyStatusPairB, cie1000PortStatusVeriPhyResultVeriPhyStatusPairC, cie1000PortStatusVeriPhyResultVeriPhyStatusPairD, cie1000PortStatusVeriPhyResultVeriPhyLengthStatusPairA, cie1000PortStatusVeriPhyResultVeriPhyLengthStatusPairB, cie1000PortStatusVeriPhyResultVeriPhyLengthStatusPairC, cie1000PortStatusVeriPhyResultVeriPhyLengthStatusPairD } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000PortMibGroups 3 } cie1000PortControlStatisticsClearTableInfoGroup OBJECT-GROUP OBJECTS { cie1000PortControlStatisticsClearIfIndex, cie1000PortControlStatisticsClearStatisticsClear } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000PortMibGroups 4 } cie1000PortControlVeriPhyStartTableInfoGroup OBJECT-GROUP OBJECTS { cie1000PortControlVeriPhyStartIfIndex, cie1000PortControlVeriPhyStartStart } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000PortMibGroups 5 } cie1000PortStatisticsRmonStatisticsTableInfoGroup OBJECT-GROUP OBJECTS { cie1000PortStatisticsRmonStatisticsIfIndex, cie1000PortStatisticsRmonStatisticsRxDropEvents, cie1000PortStatisticsRmonStatisticsRxOctets, cie1000PortStatisticsRmonStatisticsRxPkts, cie1000PortStatisticsRmonStatisticsRxBroadcastPkts, cie1000PortStatisticsRmonStatisticsRxMulticastPkts, cie1000PortStatisticsRmonStatisticsRxCrcAlignErrPkts, cie1000PortStatisticsRmonStatisticsRxUndersizePkts, cie1000PortStatisticsRmonStatisticsRxOversizePkts, cie1000PortStatisticsRmonStatisticsRxFragmentsPkts, cie1000PortStatisticsRmonStatisticsRxJabbersPkts, cie1000PortStatisticsRmonStatisticsRx64Pkts, cie1000PortStatisticsRmonStatisticsRx65to127Pkts, cie1000PortStatisticsRmonStatisticsRx128to255Pkts, cie1000PortStatisticsRmonStatisticsRx256to511Pkts, cie1000PortStatisticsRmonStatisticsRx512to1023Pkts, cie1000PortStatisticsRmonStatisticsRx1024to1518Pkts, cie1000PortStatisticsRmonStatisticsRx1519PktsToMax, cie1000PortStatisticsRmonStatisticsTxDropEvents, cie1000PortStatisticsRmonStatisticsTxOctets, cie1000PortStatisticsRmonStatisticsTxPkts, cie1000PortStatisticsRmonStatisticsTxBroadcastPkts, cie1000PortStatisticsRmonStatisticsTxMulticastPkts, cie1000PortStatisticsRmonStatisticsTx64Pkts, cie1000PortStatisticsRmonStatisticsTx65to127Pkts, cie1000PortStatisticsRmonStatisticsTx128to255Pkts, cie1000PortStatisticsRmonStatisticsTx256to511Pkts, cie1000PortStatisticsRmonStatisticsTx512to1023Pkts, cie1000PortStatisticsRmonStatisticsTx1024to1518Pkts, cie1000PortStatisticsRmonStatisticsTx1519PktsToMax } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000PortMibGroups 6 } cie1000PortStatisticsIfGroupStatisticsTableInfoGroup OBJECT-GROUP OBJECTS { cie1000PortStatisticsIfGroupStatisticsIfIndex, cie1000PortStatisticsIfGroupStatisticsRxOctets, cie1000PortStatisticsIfGroupStatisticsRxUnicastPkts, cie1000PortStatisticsIfGroupStatisticsRxMulticastPkts, cie1000PortStatisticsIfGroupStatisticsRxBroadcastPkts, cie1000PortStatisticsIfGroupStatisticsRxNonUnicastPkts, cie1000PortStatisticsIfGroupStatisticsRxDiscards, cie1000PortStatisticsIfGroupStatisticsRxErrors, cie1000PortStatisticsIfGroupStatisticsTxOctets, cie1000PortStatisticsIfGroupStatisticsTxUnicastPkts, cie1000PortStatisticsIfGroupStatisticsTxMulticastPkts, cie1000PortStatisticsIfGroupStatisticsTxBroadcastPkts, cie1000PortStatisticsIfGroupStatisticsTxNonUnicastPkts, cie1000PortStatisticsIfGroupStatisticsTxDiscardPkts, cie1000PortStatisticsIfGroupStatisticsTxErrorPkts } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000PortMibGroups 7 } cie1000PortStatisticsEthernetLikeStatisticsTableInfoGroup OBJECT-GROUP OBJECTS { cie1000PortStatisticsEthernetLikeStatisticsIfIndex, cie1000PortStatisticsEthernetLikeStatisticsRxPauseFrames, cie1000PortStatisticsEthernetLikeStatisticsTxPauseFrames } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000PortMibGroups 8 } cie1000PortStatisticsQueuesStatisticsTableInfoGroup OBJECT-GROUP OBJECTS { cie1000PortStatisticsQueuesStatisticsIfIndex, cie1000PortStatisticsQueuesStatisticsQueue, cie1000PortStatisticsQueuesStatisticsRxPrio, cie1000PortStatisticsQueuesStatisticsTxPrio } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000PortMibGroups 9 } cie1000PortStatisticsBridgeStatisticsTableInfoGroup OBJECT-GROUP OBJECTS { cie1000PortStatisticsBridgeStatisticsIfIndex, cie1000PortStatisticsBridgeStatisticsRxBridgeDiscard } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000PortMibGroups 10 } cie1000PortMibCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the implementation." MODULE -- this module MANDATORY-GROUPS { cie1000PortConfigInfoGroup, cie1000PortStatusInformationTableInfoGroup, cie1000PortStatusVeriPhyResultTableInfoGroup, cie1000PortControlStatisticsClearTableInfoGroup, cie1000PortControlVeriPhyStartTableInfoGroup, cie1000PortStatisticsRmonStatisticsTableInfoGroup, cie1000PortStatisticsIfGroupStatisticsTableInfoGroup, cie1000PortStatisticsEthernetLikeStatisticsTableInfoGroup, cie1000PortStatisticsQueuesStatisticsTableInfoGroup, cie1000PortStatisticsBridgeStatisticsTableInfoGroup } ::= { cie1000PortMibCompliances 1 } END