-- ***************************************************************** -- LLDP-MIB: Cisco private MIB -- **************************************************************** CIE1000-LLDP-MIB DEFINITIONS ::= BEGIN IMPORTS NOTIFICATION-GROUP, MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF NOTIFICATION-TYPE, MODULE-IDENTITY, OBJECT-TYPE FROM SNMPv2-SMI TEXTUAL-CONVENTION FROM SNMPv2-TC cie1000SwitchMgmt FROM CISCO-IE1000-MIB CIE1000DisplayString FROM CIE1000-TC CIE1000Integer64 FROM CIE1000-TC CIE1000InterfaceIndex FROM CIE1000-TC CIE1000RowEditorState FROM CIE1000-TC CIE1000Unsigned16 FROM CIE1000-TC CIE1000Unsigned64 FROM CIE1000-TC CIE1000Unsigned8 FROM CIE1000-TC Integer32 FROM SNMPv2-SMI Unsigned32 FROM SNMPv2-SMI TruthValue FROM SNMPv2-TC ; cie1000LldpMib MODULE-IDENTITY LAST-UPDATED "201604070000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 West Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-snmp@cisco.com" DESCRIPTION "This is a private version of the LLDP MIB" REVISION "201604070000Z" DESCRIPTION "Add SnmpNotificationEna to lldpConfig table" REVISION "201407010000Z" DESCRIPTION "Initial version" ::= { cie1000SwitchMgmt 34 } CIE1000lldpAdminState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This enumerations the admin state." SYNTAX INTEGER { disabled(0), txAndRx(1), txOnly(2), rxOnly(3) } CIE1000lldpmedAltitudeType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This enumerations the altitude type." SYNTAX INTEGER { meters(1), floors(2) } CIE1000lldpmedCivicAddressType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This enumerations the civic address type." SYNTAX INTEGER { state(1), county(2), city(3), district(4), block(5), street(6), leadingStreetDirection(16), trailingStreetSuffix(17), streetSuffix(18), houseNo(19), houseNoSuffix(20), landmark(21), additionalInfo(22), name(23), zipCode(24), building(25), apartment(26), floor(27), roomNumber(28), placeType(29), postalCommunityName(30), poBox(31), additionalCode(32) } CIE1000lldpmedDatumType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This enumerations the datum (geodetic system)." SYNTAX INTEGER { wgs84(1), nad83navd88(2), nad83mllw(3) } CIE1000lldpmedDeviceType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This enumerations the device type that the device shall operate as." SYNTAX INTEGER { connectivity(0), endpoint(1) } CIE1000lldpmedRemoteDeviceType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This enumerations the remote neighbor's device type." SYNTAX INTEGER { notDefined(0), endpointClassI(1), endpointClassII(2), endpointClassIII(3), networkConnectivity(4), reserved(5) } CIE1000lldpmedRemoteNetworkPolicyApplicationType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This enumerations the remote neighbor's network policy's application type." SYNTAX INTEGER { voice(1), voiceSignaling(2), guestVoice(3), guestVoiceSignaling(4), softphoneVoice(5), videoConferencing(6), streamingVideo(7), videoSignaling(8) } cie1000LldpMibObjects OBJECT IDENTIFIER ::= { cie1000LldpMib 1 } cie1000LldpConfig OBJECT IDENTIFIER ::= { cie1000LldpMibObjects 2 } cie1000LldpConfigGlobal OBJECT IDENTIFIER ::= { cie1000LldpConfig 1 } cie1000LldpConfigGlobalReInitDelay OBJECT-TYPE SYNTAX CIE1000Unsigned16 MAX-ACCESS read-write STATUS current DESCRIPTION "Set the LLDP tx reinitialization delay in seconds. Valid range 1-10. When a port is disabled, LLDP is disabled or the switch is rebooted, a LLDP shutdown frame is transmitted to the neighboring units, signaling that the LLDP information isn't valid anymore. Tx reinitialization delay controls the amount of seconds between the shutdown frame and a new LLDP initialization." ::= { cie1000LldpConfigGlobal 1 } cie1000LldpConfigGlobalMsgTxHold OBJECT-TYPE SYNTAX CIE1000Unsigned16 MAX-ACCESS read-write STATUS current DESCRIPTION "Set the LLDP tx hold times . Valid range 2-10. Each LLDP frame contains information about how long time the information in the LLDP frame shall be considered valid. The LLDP information valid period is set to tx hold times multiplied by tx interval seconds." ::= { cie1000LldpConfigGlobal 2 } cie1000LldpConfigGlobalMsgTxInterval OBJECT-TYPE SYNTAX CIE1000Unsigned16 MAX-ACCESS read-write STATUS current DESCRIPTION "Set the LLDP tx interval in seconds. The switch periodically transmits LLDP frames to its neighbors for having the network discovery information up-to-date. The interval between each LLDP frame is determined by the tx Interval value. Valid range 5-32768 seconds." ::= { cie1000LldpConfigGlobal 3 } cie1000LldpConfigGlobalTxDelay OBJECT-TYPE SYNTAX CIE1000Unsigned16 MAX-ACCESS read-write STATUS current DESCRIPTION "Set the LLDP tx delay in seconds. Valid range 1-8192. If some configuration is changed (e.g. the IP address) a new LLDP frame is transmitted, but the time between the LLDP frames will always be at least the value of tx delay seconds. Note: tx Delay cannot be larger than 1/4 of the tx interval." ::= { cie1000LldpConfigGlobal 4 } cie1000LldpConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000LldpConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is a table to configure LLDP configurations for a specific interface." ::= { cie1000LldpConfig 2 } cie1000LldpConfigEntry OBJECT-TYPE SYNTAX CIE1000LldpConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each interface has a set of control parameters" INDEX { cie1000LldpConfigIfIndex } ::= { cie1000LldpConfigTable 1 } CIE1000LldpConfigEntry ::= SEQUENCE { cie1000LldpConfigIfIndex CIE1000InterfaceIndex, cie1000LldpConfigAdminState CIE1000lldpAdminState, cie1000LldpConfigCdpAware TruthValue, cie1000LldpConfigOptionalTlvs CIE1000Unsigned8, cie1000LldpConfigSnmpNotificationEna TruthValue } cie1000LldpConfigIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number index." ::= { cie1000LldpConfigEntry 1 } cie1000LldpConfigAdminState OBJECT-TYPE SYNTAX CIE1000lldpAdminState MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the LLDP admin state for the interface." ::= { cie1000LldpConfigEntry 3 } cie1000LldpConfigCdpAware OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Enables/disables CDP awareness for the interface. CDP is Cisco's equivalent to LLDP. The CDP operation is restricted to decoding incoming CDP frames (The switch doesn't transmit CDP frames). CDP frames are only decoded if LLDP on the port is enabled. Only CDP TLVs that can be mapped to a corresponding field in the LLDP neighbors' table are decoded. All other TLVs are discarded (Unrecognized CDP TLVs and discarded CDP frames are not shown in the LLDP statistics.). CDP TLVs are mapped onto LLDP neighbors' table as shown below. CDP TLV 'Device ID' is mapped to the LLDP 'Chassis ID' field. CDP TLV 'Address' is mapped to the LLDP 'Management Address' field. The CDP address TLV can contain multiple addresses, but only the first address is shown in the LLDP neighbors table. CDP TLV 'Port ID' is mapped to the LLDP 'Port ID' field. CDP TLV 'Version and Platform' is mapped to the LLDP 'System Description' field. Both the CDP and LLDP support 'system capabilities', but the CDP capabilities cover capabilities that are not part of the LLDP. These capabilities are shown as 'others' in the LLDP neighbors' table. If all ports have CDP awareness disabled the switch forwards CDP frames received from neighbor devices. If at least one port has CDP awareness enabled all CDP frames are terminated by the switch. Note: When CDP awareness on a port is disabled the CDP information isn't removed immediately, but gets removed when the hold time is exceeded." ::= { cie1000LldpConfigEntry 4 } cie1000LldpConfigOptionalTlvs OBJECT-TYPE SYNTAX CIE1000Unsigned8 MAX-ACCESS read-write STATUS current DESCRIPTION "Enables/Disables the LLDP optional TLVs. Bit mask, where setting the bit to 1 means enable transmission of the corresponding TLV. Bit 0 represents Port Description TLV. Bit 1 represents System Name TLV. Bit 2 represents System Description. Bit 3 represents System Capabilities TLV. Bit 4 represents Management Address TLV." ::= { cie1000LldpConfigEntry 5 } cie1000LldpConfigSnmpNotificationEna OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable of SNMP Trap notification." ::= { cie1000LldpConfigEntry 6 } cie1000LldpConfigMed OBJECT IDENTIFIER ::= { cie1000LldpConfig 3 } cie1000LldpConfigMedTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000LldpConfigMedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is a table to configure LLDP MEDIA configurations for a specific interface." ::= { cie1000LldpConfigMed 1 } cie1000LldpConfigMedEntry OBJECT-TYPE SYNTAX CIE1000LldpConfigMedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each interface has a set of control parameters" INDEX { cie1000LldpConfigMedIfIndex } ::= { cie1000LldpConfigMedTable 1 } CIE1000LldpConfigMedEntry ::= SEQUENCE { cie1000LldpConfigMedIfIndex CIE1000InterfaceIndex, cie1000LldpConfigMedOptionalTlvs CIE1000Unsigned8, cie1000LldpConfigMedDeviceType CIE1000lldpmedDeviceType } cie1000LldpConfigMedIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number index." ::= { cie1000LldpConfigMedEntry 1 } cie1000LldpConfigMedOptionalTlvs OBJECT-TYPE SYNTAX CIE1000Unsigned8 MAX-ACCESS read-write STATUS current DESCRIPTION "Enables/Disables the LLDP optional TLVs. Bit mask, where setting the bit to 1 means enable transmission of the corresponding optional TLV. Bit 0 represents the capabilities TLV. Bit 1 represents the network Policy TLV. Bit 2 represents the location TLV. Bit 3 represents the PoE TLV." ::= { cie1000LldpConfigMedEntry 3 } cie1000LldpConfigMedDeviceType OBJECT-TYPE SYNTAX CIE1000lldpmedDeviceType MAX-ACCESS read-write STATUS current DESCRIPTION "Setting device type to configure the mode the device shall operate as." ::= { cie1000LldpConfigMedEntry 4 } cie1000LldpConfigMedPolicyTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000LldpConfigMedPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is a table to configure LLDP MED Policies for the device." ::= { cie1000LldpConfigMed 2 } cie1000LldpConfigMedPolicyEntry OBJECT-TYPE SYNTAX CIE1000LldpConfigMedPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Network Policy Discovery enables the efficient discovery and diagnosis of mismatch issues with the VLAN configuration, along with the associated Layer 2 and Layer 3 attributes, which apply for a set of specific protocol applications on that port. Improper network policy configurations are a very significant issue in VoIP environments that frequently result in voice quality degradation or loss of service. Policies are only intended for use with applications that have specific 'real-time' network policy requirements, such as interactive voice and/or video services." INDEX { cie1000LldpConfigMedPolicyLldpmedPolicy } ::= { cie1000LldpConfigMedPolicyTable 1 } CIE1000LldpConfigMedPolicyEntry ::= SEQUENCE { cie1000LldpConfigMedPolicyLldpmedPolicy Integer32, cie1000LldpConfigMedPolicyApplicationType CIE1000lldpmedRemoteNetworkPolicyApplicationType, cie1000LldpConfigMedPolicyTagged TruthValue, cie1000LldpConfigMedPolicyVlanId CIE1000Unsigned16, cie1000LldpConfigMedPolicyL2Priority CIE1000Unsigned8, cie1000LldpConfigMedPolicyDscp CIE1000Unsigned8, cie1000LldpConfigMedPolicyAction CIE1000RowEditorState } cie1000LldpConfigMedPolicyLldpmedPolicy OBJECT-TYPE SYNTAX Integer32 (0..31) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Policy index." ::= { cie1000LldpConfigMedPolicyEntry 1 } cie1000LldpConfigMedPolicyApplicationType OBJECT-TYPE SYNTAX CIE1000lldpmedRemoteNetworkPolicyApplicationType MAX-ACCESS read-write STATUS current DESCRIPTION "The LLDP policy application type." ::= { cie1000LldpConfigMedPolicyEntry 3 } cie1000LldpConfigMedPolicyTagged OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The LLDP policy tagged flag. Defines if LLDP policy uses tagged VLAN." ::= { cie1000LldpConfigMedPolicyEntry 4 } cie1000LldpConfigMedPolicyVlanId OBJECT-TYPE SYNTAX CIE1000Unsigned16 (1..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The LLDP policy VLAN ID. Only valid when policy 'Tagged' is TRUE" ::= { cie1000LldpConfigMedPolicyEntry 5 } cie1000LldpConfigMedPolicyL2Priority OBJECT-TYPE SYNTAX CIE1000Unsigned8 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The LLDP policy L2 priority." ::= { cie1000LldpConfigMedPolicyEntry 6 } cie1000LldpConfigMedPolicyDscp OBJECT-TYPE SYNTAX CIE1000Unsigned8 (0..63) MAX-ACCESS read-write STATUS current DESCRIPTION "The LLDP policy DSCP." ::= { cie1000LldpConfigMedPolicyEntry 7 } cie1000LldpConfigMedPolicyAction OBJECT-TYPE SYNTAX CIE1000RowEditorState MAX-ACCESS read-write STATUS current DESCRIPTION "Action" ::= { cie1000LldpConfigMedPolicyEntry 100 } cie1000LldpConfigMedPolicyListTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000LldpConfigMedPolicyListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each interface can be mapped to multiple policies. Set to TRUE in order to enable the corresponding policy to be transmitted at the interface. It is a requirement that the policy is defined." ::= { cie1000LldpConfigMed 3 } cie1000LldpConfigMedPolicyListEntry OBJECT-TYPE SYNTAX CIE1000LldpConfigMedPolicyListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each location information has a control parameter" INDEX { cie1000LldpConfigMedPolicyListIfIndex, cie1000LldpConfigMedPolicyListLldpmedPolicy } ::= { cie1000LldpConfigMedPolicyListTable 1 } CIE1000LldpConfigMedPolicyListEntry ::= SEQUENCE { cie1000LldpConfigMedPolicyListIfIndex CIE1000InterfaceIndex, cie1000LldpConfigMedPolicyListLldpmedPolicy Integer32, cie1000LldpConfigMedPolicyListLldpmedPoliciesList TruthValue } cie1000LldpConfigMedPolicyListIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number index." ::= { cie1000LldpConfigMedPolicyListEntry 1 } cie1000LldpConfigMedPolicyListLldpmedPolicy OBJECT-TYPE SYNTAX Integer32 (0..31) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Policy index." ::= { cie1000LldpConfigMedPolicyListEntry 3 } cie1000LldpConfigMedPolicyListLldpmedPoliciesList OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Set to TRUE assign the corresponding policy index to the interface." ::= { cie1000LldpConfigMedPolicyListEntry 4 } cie1000LldpConfigMedGlobal OBJECT IDENTIFIER ::= { cie1000LldpConfigMed 4 } cie1000LldpConfigMedGlobalFastRepeatCount OBJECT-TYPE SYNTAX CIE1000Unsigned8 (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of times to repeat LLDP frame transmission at fast start Rapid startup and Emergency Call Service Location Identification Discovery of endpoints is a critically important aspect of VoIP systems in general. In addition, it is best to advertise only those pieces of information which are specifically relevant to particular endpoint types (for example only advertise the voice network policy to permitted voice-capable devices), both in order to conserve the limited LLDPU space and to reduce security and system integrity issues that can come with inappropriate knowledge of the network policy. With this in mind LLDP-MED defines an LLDP-MED Fast Start interaction between the protocol and the application layers on top of the protocol, in order to achieve these related properties. Initially, a Network Connectivity Device will only transmit LLDP TLVs in an LLDPDU. Only after an LLDP-MED Endpoint Device is detected, will an LLDP-MED capable Network Connectivity Device start to advertise LLDP-MED TLVs in outgoing LLDPDUs on the associated port. The LLDP-MED application will temporarily speed up the transmission of the LLDPDU to start within a second, when a new LLDP-MED neighbor has been detected in order share LLDP-MED information as fast as possible to new neighbors. Because there is a risk of an LLDP frame being lost during transmission between neighbors, it is recommended to repeat the fast start transmission multiple times to increase the possibility of the neighbors receiving the LLDP frame. With fast start repeat count it is possible to specify the number of times the fast start transmission would be repeated. The recommended value is 4 times, given that 4 LLDP frames with a 1 second interval will be transmitted, when an LLDP frame with new information is received. It should be noted that LLDP-MED and the LLDP-MED Fast Start mechanism is only intended to run on links between LLDP-MED Network Connectivity Devices and Endpoint Devices, and as such does not apply to links between LAN infrastructure elements, including Network Connectivity Devices, or other types of links." ::= { cie1000LldpConfigMedGlobal 1 } cie1000LldpConfigMedGlobalLatitude OBJECT-TYPE SYNTAX CIE1000Integer64 MAX-ACCESS read-write STATUS current DESCRIPTION "Latitude degrees in 2s-complement as specified in RFC 3825. Positive numbers are north of the equator and negative numbers are south of the equator." ::= { cie1000LldpConfigMedGlobal 2 } cie1000LldpConfigMedGlobalLongitude OBJECT-TYPE SYNTAX CIE1000Integer64 MAX-ACCESS read-write STATUS current DESCRIPTION "Longitude degrees in 2s-complement as specified in RFC 3825. Positive values are East of the prime meridian and negative numbers are West of the prime meridian." ::= { cie1000LldpConfigMedGlobal 3 } cie1000LldpConfigMedGlobalAltitudeType OBJECT-TYPE SYNTAX CIE1000lldpmedAltitudeType MAX-ACCESS read-write STATUS current DESCRIPTION "Setting altitude type Possible to select between two altitude types (floors or meters). Meters are representing meters of altitude defined by the vertical datum specified. Floors are representing altitude in a form more relevant in buildings which have different floor-to-floor dimensions. An altitude = 0.0 is meaningful even outside a building, and represents ground level at the given latitude and longitude. Inside a building, 0.0 represents the floor level associated with ground level at the main entrance." ::= { cie1000LldpConfigMedGlobal 4 } cie1000LldpConfigMedGlobalAltitude OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Altitude value in 2s-complement as specified in RFC 3825" ::= { cie1000LldpConfigMedGlobal 5 } cie1000LldpConfigMedGlobalElinAddr OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..25)) MAX-ACCESS read-write STATUS current DESCRIPTION "Emergency Call Service ELIN identifier data format is defined to carry the ELIN identifier as used during emergency call setup to a traditional CAMA or ISDN trunk-based PSAP. This format consists of a numerical digit string, corresponding to the ELIN to be used for emergency calling. Maximum number of octets are 25." ::= { cie1000LldpConfigMedGlobal 6 } cie1000LldpConfigMedGlobalDatum OBJECT-TYPE SYNTAX CIE1000lldpmedDatumType MAX-ACCESS read-write STATUS current DESCRIPTION "Setting datum to configure the datum (geodetic system) to use. The Map Datum is used for the coordinates given in these options: WGS84: (Geographical 3D) - World Geodesic System 1984, CRS Code 4327, Prime Meridian Name: Greenwich. NAD83/NAVD88: North American Datum 1983, CRS Code 4269, Prime Meridian Name: Greenwich;The associated vertical datum is the North American Vertical Datum of 1988 (NAVD88).This datum pair is to be used when referencing locations on land, not near tidal water(which would use Datum = NAD83/MLLW). NAD83/MLLW: North American Datum 1983, CRS Code 4269, Prime Meridian Name: Greenwich; The associated vertical datum is Mean Lower Low Water (MLLW). This datum pair is to be used when referencing locations on water/sea/ocean." ::= { cie1000LldpConfigMedGlobal 7 } cie1000LldpConfigMedGlobalCountryCode OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..2)) MAX-ACCESS read-write STATUS current DESCRIPTION "The two-letter ISO 3166 country code in capital ASCII letters - Example: DK, DE or US." ::= { cie1000LldpConfigMedGlobal 8 } cie1000LldpConfigMedLocationInfTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000LldpConfigMedLocationInfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The civic address location information. Each civic address can contain up to 250 characters, but the total amount of characters for the combined civic address locations must not exceed 250 bytes. Note: If an civic address location is non-empty it uses the amount of characters plus addition two characters. This is described in TIA1057, Section 10.2.4.3.2." ::= { cie1000LldpConfigMed 5 } cie1000LldpConfigMedLocationInfEntry OBJECT-TYPE SYNTAX CIE1000LldpConfigMedLocationInfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each civic address type as defined in TIA1057, Section 3.4 in Annex B" INDEX { cie1000LldpConfigMedLocationInfLldpmedIndex } ::= { cie1000LldpConfigMedLocationInfTable 1 } CIE1000LldpConfigMedLocationInfEntry ::= SEQUENCE { cie1000LldpConfigMedLocationInfLldpmedIndex CIE1000lldpmedCivicAddressType, cie1000LldpConfigMedLocationInfCivicAddress CIE1000DisplayString } cie1000LldpConfigMedLocationInfLldpmedIndex OBJECT-TYPE SYNTAX CIE1000lldpmedCivicAddressType MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Civic address type. 1 - State/National subdivisions 2 - County, parish, gun (JP), district (IN) 3 - City, township 4 - City division, borough, city district, ward, chou (JP) 5 - Neighborhood, block 6 - Street 16 - Leading street direction 17 - Trailing street direction 18 - Street suffix 19 - House number 20 - House number suffix 21 - Landmark or vanity address 22 - Additional location information 23 - Name 24 - Postal/zip code 25 - Building 26 - Unit 27 - Floor 28 - Room 29 - Place type 30 - Postal 31 - Post office 32 - Additional code" ::= { cie1000LldpConfigMedLocationInfEntry 2 } cie1000LldpConfigMedLocationInfCivicAddress OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-write STATUS current DESCRIPTION "Civic address" ::= { cie1000LldpConfigMedLocationInfEntry 3 } cie1000LldpConfigMedPolicyRowEditor OBJECT IDENTIFIER ::= { cie1000LldpConfigMed 6 } cie1000LldpConfigMedPolicyRowEditorLldpmedPolicy OBJECT-TYPE SYNTAX Integer32 (0..31) MAX-ACCESS read-write STATUS current DESCRIPTION "Policy index." ::= { cie1000LldpConfigMedPolicyRowEditor 1 } cie1000LldpConfigMedPolicyRowEditorApplicationType OBJECT-TYPE SYNTAX CIE1000lldpmedRemoteNetworkPolicyApplicationType MAX-ACCESS read-write STATUS current DESCRIPTION "The LLDP policy application type." ::= { cie1000LldpConfigMedPolicyRowEditor 3 } cie1000LldpConfigMedPolicyRowEditorTagged OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The LLDP policy tagged flag. Defines if LLDP policy uses tagged VLAN." ::= { cie1000LldpConfigMedPolicyRowEditor 4 } cie1000LldpConfigMedPolicyRowEditorVlanId OBJECT-TYPE SYNTAX CIE1000Unsigned16 (1..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The LLDP policy VLAN ID. Only valid when policy 'Tagged' is TRUE" ::= { cie1000LldpConfigMedPolicyRowEditor 5 } cie1000LldpConfigMedPolicyRowEditorL2Priority OBJECT-TYPE SYNTAX CIE1000Unsigned8 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The LLDP policy L2 priority." ::= { cie1000LldpConfigMedPolicyRowEditor 6 } cie1000LldpConfigMedPolicyRowEditorDscp OBJECT-TYPE SYNTAX CIE1000Unsigned8 (0..63) MAX-ACCESS read-write STATUS current DESCRIPTION "The LLDP policy DSCP." ::= { cie1000LldpConfigMedPolicyRowEditor 7 } cie1000LldpConfigMedPolicyRowEditorAction OBJECT-TYPE SYNTAX CIE1000RowEditorState MAX-ACCESS read-write STATUS current DESCRIPTION "Action" ::= { cie1000LldpConfigMedPolicyRowEditor 100 } cie1000LldpStatus OBJECT IDENTIFIER ::= { cie1000LldpMibObjects 3 } cie1000LldpStatusStatistics OBJECT IDENTIFIER ::= { cie1000LldpStatus 1 } cie1000LldpStatusStatisticsGlobalCounters OBJECT IDENTIFIER ::= { cie1000LldpStatusStatistics 1 } cie1000LldpStatusStatisticsGlobalCountersTableInserts OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of new entries added since switch reboot." ::= { cie1000LldpStatusStatisticsGlobalCounters 1 } cie1000LldpStatusStatisticsGlobalCountersTableDeletes OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of new entries deleted since switch reboot." ::= { cie1000LldpStatusStatisticsGlobalCounters 2 } cie1000LldpStatusStatisticsGlobalCountersTableDrops OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of LLDP frames dropped due to the entry table being full." ::= { cie1000LldpStatusStatisticsGlobalCounters 3 } cie1000LldpStatusStatisticsGlobalCountersTableAgeOuts OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of entries deleted due to Time-To-Live expiring." ::= { cie1000LldpStatusStatisticsGlobalCounters 4 } cie1000LldpStatusStatisticsGlobalCountersLastChangeTime OBJECT-TYPE SYNTAX CIE1000Unsigned64 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the time when the last entry was last deleted or added. It also shows the time elapsed since the last change was detected." ::= { cie1000LldpStatusStatisticsGlobalCounters 5 } cie1000LldpStatusStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000LldpStatusStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the LLDP interface counters" ::= { cie1000LldpStatusStatistics 2 } cie1000LldpStatusStatisticsEntry OBJECT-TYPE SYNTAX CIE1000LldpStatusStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each port interface has a set of statistics counters" INDEX { cie1000LldpStatusStatisticsIfIndex } ::= { cie1000LldpStatusStatisticsTable 1 } CIE1000LldpStatusStatisticsEntry ::= SEQUENCE { cie1000LldpStatusStatisticsIfIndex CIE1000InterfaceIndex, cie1000LldpStatusStatisticsTxTotal Unsigned32, cie1000LldpStatusStatisticsRxTotal Unsigned32, cie1000LldpStatusStatisticsRxError Unsigned32, cie1000LldpStatusStatisticsRxDiscarded Unsigned32, cie1000LldpStatusStatisticsTLVsDiscarded Unsigned32, cie1000LldpStatusStatisticsTLVsUnrecognized Unsigned32, cie1000LldpStatusStatisticsTLVsOrgDiscarded Unsigned32, cie1000LldpStatusStatisticsAgeOuts Unsigned32 } cie1000LldpStatusStatisticsIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number index." ::= { cie1000LldpStatusStatisticsEntry 1 } cie1000LldpStatusStatisticsTxTotal OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of LLDP frames transmitted." ::= { cie1000LldpStatusStatisticsEntry 2 } cie1000LldpStatusStatisticsRxTotal OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of LLDP frames received." ::= { cie1000LldpStatusStatisticsEntry 3 } cie1000LldpStatusStatisticsRxError OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of received LLDP frames containing some kind of error." ::= { cie1000LldpStatusStatisticsEntry 4 } cie1000LldpStatusStatisticsRxDiscarded OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Show the number of LLDP frames discarded. If a LLDP frame is received at an interface, and the switch's internal table has run full, the LLDP frame is counted and discarded. This situation is known as 'Too Many Neighbors' in the LLDP standard. LLDP frames require a new entry in the table when the Chassis ID or Remote Port ID is not already contained within the table. Entries are removed from the table when a given interface's link is down, an LLDP shutdown frame is received, or when the entry ages out." ::= { cie1000LldpStatusStatisticsEntry 5 } cie1000LldpStatusStatisticsTLVsDiscarded OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of TLVs discarded. Each LLDP frame can contain multiple pieces of information, known as TLVs (TLV is short for 'Type Length Value'). If a TLV is malformed, it is counted and discarded." ::= { cie1000LldpStatusStatisticsEntry 6 } cie1000LldpStatusStatisticsTLVsUnrecognized OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of well-formed TLVs, but with an unknown type value." ::= { cie1000LldpStatusStatisticsEntry 7 } cie1000LldpStatusStatisticsTLVsOrgDiscarded OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the number of well-formed TLVs, but with an organizationally TLV which is not supported." ::= { cie1000LldpStatusStatisticsEntry 8 } cie1000LldpStatusStatisticsAgeOuts OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Show the number of age-outs. Each frame contains information about how long time the LLDP information is valid (age-out time). If no new LLDP frame is received within the age out time, the information is removed, and the counter is incremented." ::= { cie1000LldpStatusStatisticsEntry 9 } cie1000LldpStatusNeighborsInfTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000LldpStatusNeighborsInfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is a table to show the LLDP neighbors information for a specific interface." ::= { cie1000LldpStatus 2 } cie1000LldpStatusNeighborsInfEntry OBJECT-TYPE SYNTAX CIE1000LldpStatusNeighborsInfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each interface has a set of neighbors information" INDEX { cie1000LldpStatusNeighborsInfIfIndex, cie1000LldpStatusNeighborsInfLldpmedIndex } ::= { cie1000LldpStatusNeighborsInfTable 1 } CIE1000LldpStatusNeighborsInfEntry ::= SEQUENCE { cie1000LldpStatusNeighborsInfIfIndex CIE1000InterfaceIndex, cie1000LldpStatusNeighborsInfLldpmedIndex Integer32, cie1000LldpStatusNeighborsInfChassisId CIE1000DisplayString, cie1000LldpStatusNeighborsInfPortId CIE1000DisplayString, cie1000LldpStatusNeighborsInfPortDescription CIE1000DisplayString, cie1000LldpStatusNeighborsInfSystemName CIE1000DisplayString, cie1000LldpStatusNeighborsInfSystemDescription CIE1000DisplayString, cie1000LldpStatusNeighborsInfSystemCapabilities CIE1000Unsigned16, cie1000LldpStatusNeighborsInfSystemCapabilitiesEnable CIE1000Unsigned16 } cie1000LldpStatusNeighborsInfIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number index." ::= { cie1000LldpStatusNeighborsInfEntry 1 } cie1000LldpStatusNeighborsInfLldpmedIndex OBJECT-TYPE SYNTAX Integer32 (0..192) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Neighbor information table entry index." ::= { cie1000LldpStatusNeighborsInfEntry 2 } cie1000LldpStatusNeighborsInfChassisId OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..254)) MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's chassis Id." ::= { cie1000LldpStatusNeighborsInfEntry 4 } cie1000LldpStatusNeighborsInfPortId OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..254)) MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's port id." ::= { cie1000LldpStatusNeighborsInfEntry 5 } cie1000LldpStatusNeighborsInfPortDescription OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..254)) MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's port description." ::= { cie1000LldpStatusNeighborsInfEntry 6 } cie1000LldpStatusNeighborsInfSystemName OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..254)) MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's system name." ::= { cie1000LldpStatusNeighborsInfEntry 7 } cie1000LldpStatusNeighborsInfSystemDescription OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..254)) MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's system description." ::= { cie1000LldpStatusNeighborsInfEntry 8 } cie1000LldpStatusNeighborsInfSystemCapabilities OBJECT-TYPE SYNTAX CIE1000Unsigned16 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's system capabilities as bit mask. If the bit is set, it means that the functionality is supported by the neighbor system. Bit 0 represents Other. Bit 1 represents Repeater. Bit 2 represents Bridge. Bit 3 represents WLAN Access Point. Bit 4 represents Router. Bit 5 represents Telephone. Bit 6 represents DOCSIS cable device. Bit 7 represents Station Only. Bit 8 represents Reserved." ::= { cie1000LldpStatusNeighborsInfEntry 9 } cie1000LldpStatusNeighborsInfSystemCapabilitiesEnable OBJECT-TYPE SYNTAX CIE1000Unsigned16 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's system capabilities which is enabled. If the bit is set, it means that the functionality is currently enabled at the neighbor system. Bit 0 represents Other. Bit 1 represents Repeater. Bit 2 represents Bridge. Bit 3 represents WLAN Access Point. Bit 4 represents Router. Bit 5 represents Telephone. Bit 6 represents DOCSIS cable device. Bit 7 represents Station Only. Bit 8 represents Reserved." ::= { cie1000LldpStatusNeighborsInfEntry 10 } cie1000LldpStatusNeighborsMgmtInfTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000LldpStatusNeighborsMgmtInfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is a table to show the LLDP neighbors information for a specific interface." ::= { cie1000LldpStatus 3 } cie1000LldpStatusNeighborsMgmtInfEntry OBJECT-TYPE SYNTAX CIE1000LldpStatusNeighborsMgmtInfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each interface has a set of neighbors information" INDEX { cie1000LldpStatusNeighborsMgmtInfIfIndex, cie1000LldpStatusNeighborsMgmtInfLldpmedIndex, cie1000LldpStatusNeighborsMgmtInfLldpManagement } ::= { cie1000LldpStatusNeighborsMgmtInfTable 1 } CIE1000LldpStatusNeighborsMgmtInfEntry ::= SEQUENCE { cie1000LldpStatusNeighborsMgmtInfIfIndex CIE1000InterfaceIndex, cie1000LldpStatusNeighborsMgmtInfLldpmedIndex Integer32, cie1000LldpStatusNeighborsMgmtInfLldpManagement Integer32, cie1000LldpStatusNeighborsMgmtInfSystemMgmAddressSubtype CIE1000Unsigned8, cie1000LldpStatusNeighborsMgmtInfSystemMgmtAddress CIE1000DisplayString, cie1000LldpStatusNeighborsMgmtInfSystemMgmtInterfaceSubtype Integer32, cie1000LldpStatusNeighborsMgmtInfSystemMgmtInterface Integer32, cie1000LldpStatusNeighborsMgmtInfSystemMgmtOid OBJECT IDENTIFIER } cie1000LldpStatusNeighborsMgmtInfIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number index." ::= { cie1000LldpStatusNeighborsMgmtInfEntry 1 } cie1000LldpStatusNeighborsMgmtInfLldpmedIndex OBJECT-TYPE SYNTAX Integer32 (0..192) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Neighbor information table entry index." ::= { cie1000LldpStatusNeighborsMgmtInfEntry 2 } cie1000LldpStatusNeighborsMgmtInfLldpManagement OBJECT-TYPE SYNTAX Integer32 (0..1) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Neighbor management information table entry index." ::= { cie1000LldpStatusNeighborsMgmtInfEntry 4 } cie1000LldpStatusNeighborsMgmtInfSystemMgmAddressSubtype OBJECT-TYPE SYNTAX CIE1000Unsigned8 MAX-ACCESS read-only STATUS current DESCRIPTION "LLDP neighbor's management address subtype , section 9.5.9.3 IEEE802.1AB-2005." ::= { cie1000LldpStatusNeighborsMgmtInfEntry 5 } cie1000LldpStatusNeighborsMgmtInfSystemMgmtAddress OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "LLDP neighbor's management address string, section 9.5.9.4 IEEE802.1AB-2005." ::= { cie1000LldpStatusNeighborsMgmtInfEntry 6 } cie1000LldpStatusNeighborsMgmtInfSystemMgmtInterfaceSubtype OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Interface numbering subtype, section 9.5.9.5 IEEE802.1AB-2005." ::= { cie1000LldpStatusNeighborsMgmtInfEntry 7 } cie1000LldpStatusNeighborsMgmtInfSystemMgmtInterface OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Interface number, section 9.5.9.6 IEEE802.1AB-2005." ::= { cie1000LldpStatusNeighborsMgmtInfEntry 8 } cie1000LldpStatusNeighborsMgmtInfSystemMgmtOid OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "Object identifier, section 9.5.9.8 IEEE802.1AB-2005." ::= { cie1000LldpStatusNeighborsMgmtInfEntry 9 } cie1000LldpStatusMed OBJECT IDENTIFIER ::= { cie1000LldpStatus 4 } cie1000LldpStatusMedRemoteDeviceInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000LldpStatusMedRemoteDeviceInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is a table to show the LLDP neighbors information for a specific interface." ::= { cie1000LldpStatusMed 1 } cie1000LldpStatusMedRemoteDeviceInfoEntry OBJECT-TYPE SYNTAX CIE1000LldpStatusMedRemoteDeviceInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each interface has a set of neighbors information" INDEX { cie1000LldpStatusMedRemoteDeviceInfoIfIndex, cie1000LldpStatusMedRemoteDeviceInfoLldpmedIndex } ::= { cie1000LldpStatusMedRemoteDeviceInfoTable 1 } CIE1000LldpStatusMedRemoteDeviceInfoEntry ::= SEQUENCE { cie1000LldpStatusMedRemoteDeviceInfoIfIndex CIE1000InterfaceIndex, cie1000LldpStatusMedRemoteDeviceInfoLldpmedIndex Integer32, cie1000LldpStatusMedRemoteDeviceInfoCapabilities CIE1000Unsigned16, cie1000LldpStatusMedRemoteDeviceInfoCapabilitiesEnabled CIE1000Unsigned16, cie1000LldpStatusMedRemoteDeviceInfoLatitude CIE1000Integer64, cie1000LldpStatusMedRemoteDeviceInfoLongitude CIE1000Integer64, cie1000LldpStatusMedRemoteDeviceInfoAltitudeType CIE1000lldpmedAltitudeType, cie1000LldpStatusMedRemoteDeviceInfoAltitude Integer32, cie1000LldpStatusMedRemoteDeviceInfoDatum CIE1000lldpmedDatumType, cie1000LldpStatusMedRemoteDeviceInfoElinaddr CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceInfoDeviceType CIE1000lldpmedRemoteDeviceType, cie1000LldpStatusMedRemoteDeviceInfoHwRev CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceInfoFwRev CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceInfoSwRev CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceInfoSerialNo CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceInfoManufacturerName CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceInfoModelName CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceInfoAssetId CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceInfoEeeRxTwSys CIE1000Unsigned16, cie1000LldpStatusMedRemoteDeviceInfoEeeTxTwSys CIE1000Unsigned16, cie1000LldpStatusMedRemoteDeviceInfoEeeFbTwSys CIE1000Unsigned16, cie1000LldpStatusMedRemoteDeviceInfoEeeTxTwSysEcho CIE1000Unsigned16, cie1000LldpStatusMedRemoteDeviceInfoEeeRxTwSysEcho CIE1000Unsigned16 } cie1000LldpStatusMedRemoteDeviceInfoIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number index." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 1 } cie1000LldpStatusMedRemoteDeviceInfoLldpmedIndex OBJECT-TYPE SYNTAX Integer32 (0..192) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Neighbor information table entry index." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 2 } cie1000LldpStatusMedRemoteDeviceInfoCapabilities OBJECT-TYPE SYNTAX CIE1000Unsigned16 MAX-ACCESS read-only STATUS current DESCRIPTION "LLDP neighbor's capabilities bit mask. Bit 0 represents LLDP-MED capabilities. Bit 1 represents Network Policy. Bit 2 represents Location Identification. Bit 3 represents Extended Power via MDI - PSE. Bit 4 represents Extended Power via MDI - PD Bit 5 represents Inventory " ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 4 } cie1000LldpStatusMedRemoteDeviceInfoCapabilitiesEnabled OBJECT-TYPE SYNTAX CIE1000Unsigned16 MAX-ACCESS read-only STATUS current DESCRIPTION "LLDP neighbor's capabilities bit mask for the capabilities which are currently enabled. Bit 0 represents LLDP-MED capabilities. Bit 1 represents Network Policy. Bit 2 represents Location Identification. Bit 3 represents Extended Power via MDI - PSE. Bit 4 represents Extended Power via MDI - PD Bit 5 represents Inventory " ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 5 } cie1000LldpStatusMedRemoteDeviceInfoLatitude OBJECT-TYPE SYNTAX CIE1000Integer64 MAX-ACCESS read-only STATUS current DESCRIPTION "Latitude degrees in 2s-complement as specified in RFC 3825. Positive numbers are north of the equator and negative numbers are south of the equator." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 6 } cie1000LldpStatusMedRemoteDeviceInfoLongitude OBJECT-TYPE SYNTAX CIE1000Integer64 MAX-ACCESS read-only STATUS current DESCRIPTION "Longitude degrees in 2s-complement as specified in RFC 3825. Positive values are East of the prime meridian and negative numbers are West of the prime meridian." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 7 } cie1000LldpStatusMedRemoteDeviceInfoAltitudeType OBJECT-TYPE SYNTAX CIE1000lldpmedAltitudeType MAX-ACCESS read-only STATUS current DESCRIPTION "Altitude type as either floors or meters. Meters are representing meters of altitude defined by the vertical datum specified. Floors are representing altitude in a form more relevant in buildings which have different floor-to-floor dimensions. An altitude = 0.0 is meaningful even outside a building, and represents ground level at the given latitude and longitude. Inside a building, 0.0 represents the floor level associated with ground level at the main entrance." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 8 } cie1000LldpStatusMedRemoteDeviceInfoAltitude OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Altitude value in 2s-complement as specified in RFC 3825" ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 9 } cie1000LldpStatusMedRemoteDeviceInfoDatum OBJECT-TYPE SYNTAX CIE1000lldpmedDatumType MAX-ACCESS read-only STATUS current DESCRIPTION "Datum (geodetic system) . The Map Datum is used for the coordinates given in these options: WGS84: (Geographical 3D) - World Geodesic System 1984, CRS Code 4327, Prime Meridian Name: Greenwich. NAD83/NAVD88: North American Datum 1983, CRS Code 4269, Prime Meridian Name: Greenwich; The associated vertical datum is the North American Vertical Datum of 1988 (NAVD88). This datum pair is to be used when referencing locations on land, not near tidal water(which would use Datum = NAD83/MLLW). NAD83/MLLW: North American Datum 1983, CRS Code 4269, Prime Meridian Name: Greenwich; The associated vertical datum is Mean Lower Low Water (MLLW). This datum pair is to be used when referencing locations on water/sea/ocean." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 10 } cie1000LldpStatusMedRemoteDeviceInfoElinaddr OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..25)) MAX-ACCESS read-only STATUS current DESCRIPTION "Emergency Call Service ELIN identifier data format is defined to carry the ELIN identifier as used during emergency call setup to a traditional CAMA or ISDN trunk-based PSAP. This format consists of a numerical digit string, corresponding to the ELIN to be used for emergency calling. Maximum number of octets are 25." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 11 } cie1000LldpStatusMedRemoteDeviceInfoDeviceType OBJECT-TYPE SYNTAX CIE1000lldpmedRemoteDeviceType MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's device type." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 12 } cie1000LldpStatusMedRemoteDeviceInfoHwRev OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's hardware revision." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 13 } cie1000LldpStatusMedRemoteDeviceInfoFwRev OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's firmware revision." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 14 } cie1000LldpStatusMedRemoteDeviceInfoSwRev OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's software revision." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 15 } cie1000LldpStatusMedRemoteDeviceInfoSerialNo OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's serial number." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 16 } cie1000LldpStatusMedRemoteDeviceInfoManufacturerName OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's manufacturer name." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 17 } cie1000LldpStatusMedRemoteDeviceInfoModelName OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's model name." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 18 } cie1000LldpStatusMedRemoteDeviceInfoAssetId OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's asset id." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 19 } cie1000LldpStatusMedRemoteDeviceInfoEeeRxTwSys OBJECT-TYPE SYNTAX CIE1000Unsigned16 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's Receive tw_sys_rx . Tw_sys_rx is defined as the time (expressed in microseconds) that the transmitting link partner will wait before it starts transmitting data after leaving the Low Power Idle (LPI) mode. Section 79.3.5.2, IEEE802.3az." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 20 } cie1000LldpStatusMedRemoteDeviceInfoEeeTxTwSys OBJECT-TYPE SYNTAX CIE1000Unsigned16 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's Transmit Tw_sys_tx . Tw_sys_tx is defined as the time (expressed in microseconds) that the receiving link partner is requesting the transmitting link partner to wait before starting the transmission data following the Low Power Idle (LPI) mode. Section 79.3.5.1, IEEE802.3az." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 21 } cie1000LldpStatusMedRemoteDeviceInfoEeeFbTwSys OBJECT-TYPE SYNTAX CIE1000Unsigned16 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's Fallback tw_sys_tx. A receiving link partner may inform the transmitter of an alternate desired Tw_sys_tx. Since a receiving link partner is likely to have discrete levels for savings, this provides the transmitter with additional information that it may use for a more efficient allocation. Section 79.3.5.3, IEEE802.3az." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 22 } cie1000LldpStatusMedRemoteDeviceInfoEeeTxTwSysEcho OBJECT-TYPE SYNTAX CIE1000Unsigned16 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's echo transmit Tw. The respective echo values shall be defined as the local link partners reflection (echo) of the remote link partners respective values. When a local link partner receives its echoed values from the remote link partner it can determine whether or not the remote link partner has received, registered, and processed its most recent values. Section 79.3.5.4, IEEE802.3az." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 23 } cie1000LldpStatusMedRemoteDeviceInfoEeeRxTwSysEcho OBJECT-TYPE SYNTAX CIE1000Unsigned16 MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's echo receive Tw. The respective echo values shall be defined as the local link partners reflection (echo) of the remote link partners respective values. When a local link partner receives its echoed values from the remote link partner it can determine whether or not the remote link partner has received, registered, and processed its most recent values. Section 79.3.5.4, IEEE802.3az." ::= { cie1000LldpStatusMedRemoteDeviceInfoEntry 24 } cie1000LldpStatusMedRemoteDeviceLocInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000LldpStatusMedRemoteDeviceLocInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is a table to show the LLDP-MED remote device (neighbor) civic location information for a specific interface." ::= { cie1000LldpStatusMed 2 } cie1000LldpStatusMedRemoteDeviceLocInfoEntry OBJECT-TYPE SYNTAX CIE1000LldpStatusMedRemoteDeviceLocInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each interface has a set of neighbors information" INDEX { cie1000LldpStatusMedRemoteDeviceLocInfoIfIndex, cie1000LldpStatusMedRemoteDeviceLocInfoLldpmedIndex } ::= { cie1000LldpStatusMedRemoteDeviceLocInfoTable 1 } CIE1000LldpStatusMedRemoteDeviceLocInfoEntry ::= SEQUENCE { cie1000LldpStatusMedRemoteDeviceLocInfoIfIndex CIE1000InterfaceIndex, cie1000LldpStatusMedRemoteDeviceLocInfoLldpmedIndex Integer32, cie1000LldpStatusMedRemoteDeviceLocInfoState CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoCounty CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoCity CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoDistrict CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoBlock CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoStreet CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoLeadingStreetDirection CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoTrailingStreetSuffix CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoStreetSuffix CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoHouseNo CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoHouseNoSuffix CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoLandmark CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoAdditionalInfo CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoName CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoZipCode CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoBuilding CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoApartment CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoFloor CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoRoomNumber CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoPlaceType CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoPostalCommunityName CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoPoBox CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoAdditionalCode CIE1000DisplayString, cie1000LldpStatusMedRemoteDeviceLocInfoCountryCode CIE1000DisplayString } cie1000LldpStatusMedRemoteDeviceLocInfoIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number index." ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 1 } cie1000LldpStatusMedRemoteDeviceLocInfoLldpmedIndex OBJECT-TYPE SYNTAX Integer32 (0..192) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Neighbor information table entry index." ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 2 } cie1000LldpStatusMedRemoteDeviceLocInfoState OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "National subdivision" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 5 } cie1000LldpStatusMedRemoteDeviceLocInfoCounty OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "County" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 6 } cie1000LldpStatusMedRemoteDeviceLocInfoCity OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "City" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 7 } cie1000LldpStatusMedRemoteDeviceLocInfoDistrict OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "City district" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 8 } cie1000LldpStatusMedRemoteDeviceLocInfoBlock OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "Block (Neighborhood)" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 9 } cie1000LldpStatusMedRemoteDeviceLocInfoStreet OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "Street" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 10 } cie1000LldpStatusMedRemoteDeviceLocInfoLeadingStreetDirection OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "Street Direction" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 11 } cie1000LldpStatusMedRemoteDeviceLocInfoTrailingStreetSuffix OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "Trailing Street Suffix" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 12 } cie1000LldpStatusMedRemoteDeviceLocInfoStreetSuffix OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "Street Suffix" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 13 } cie1000LldpStatusMedRemoteDeviceLocInfoHouseNo OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "House No." ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 14 } cie1000LldpStatusMedRemoteDeviceLocInfoHouseNoSuffix OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "House No. Suffix" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 15 } cie1000LldpStatusMedRemoteDeviceLocInfoLandmark OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "Landmark" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 16 } cie1000LldpStatusMedRemoteDeviceLocInfoAdditionalInfo OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "Additional Location Info" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 17 } cie1000LldpStatusMedRemoteDeviceLocInfoName OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "Name" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 18 } cie1000LldpStatusMedRemoteDeviceLocInfoZipCode OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "Zip code" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 19 } cie1000LldpStatusMedRemoteDeviceLocInfoBuilding OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "Building" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 20 } cie1000LldpStatusMedRemoteDeviceLocInfoApartment OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "Apartment/unit" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 21 } cie1000LldpStatusMedRemoteDeviceLocInfoFloor OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "Floor" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 22 } cie1000LldpStatusMedRemoteDeviceLocInfoRoomNumber OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "Room Number" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 23 } cie1000LldpStatusMedRemoteDeviceLocInfoPlaceType OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "Place type" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 24 } cie1000LldpStatusMedRemoteDeviceLocInfoPostalCommunityName OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "Postal Community Name" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 25 } cie1000LldpStatusMedRemoteDeviceLocInfoPoBox OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "Post Office Box" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 26 } cie1000LldpStatusMedRemoteDeviceLocInfoAdditionalCode OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..250)) MAX-ACCESS read-only STATUS current DESCRIPTION "Additional Code" ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 27 } cie1000LldpStatusMedRemoteDeviceLocInfoCountryCode OBJECT-TYPE SYNTAX CIE1000DisplayString (SIZE(0..2)) MAX-ACCESS read-only STATUS current DESCRIPTION "The two-letter ISO 3166 country code in capital ASCII letters - Example: DK, DE or US." ::= { cie1000LldpStatusMedRemoteDeviceLocInfoEntry 28 } cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is a table to show the LLDP-MED remote device (neighbor) network policies information for a specific interface." ::= { cie1000LldpStatusMed 3 } cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry OBJECT-TYPE SYNTAX CIE1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each interface has a set of neighbors information" INDEX { cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoIfIndex, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoLldpmedIndex, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoLldpmedPolicy } ::= { cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoTable 1 } CIE1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry ::= SEQUENCE { cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoIfIndex CIE1000InterfaceIndex, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoLldpmedIndex Integer32, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoLldpmedPolicy Integer32, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoApplicationType CIE1000lldpmedRemoteNetworkPolicyApplicationType, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoUnknownPolicy TruthValue, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoTagged TruthValue, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoVlanId CIE1000Unsigned16, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoL2Priority CIE1000Unsigned8, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoDscp CIE1000Unsigned8 } cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number index." ::= { cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry 1 } cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoLldpmedIndex OBJECT-TYPE SYNTAX Integer32 (0..192) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Neighbor information table entry index." ::= { cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry 2 } cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoLldpmedPolicy OBJECT-TYPE SYNTAX Integer32 (0..31) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Policy index." ::= { cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry 3 } cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoApplicationType OBJECT-TYPE SYNTAX CIE1000lldpmedRemoteNetworkPolicyApplicationType MAX-ACCESS read-only STATUS current DESCRIPTION "The LLDP policy application type." ::= { cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry 5 } cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoUnknownPolicy OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Policy indicates that an Endpoint Device wants to explicitly advertise that the policy is required by the device. Can be either Defined or Unknown Unknown: The network policy for the specified application type is currently unknown. Defined: The network policy is defined (known)." ::= { cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry 6 } cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoTagged OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Defines if LLDP policy uses tagged VLAN." ::= { cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry 7 } cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoVlanId OBJECT-TYPE SYNTAX CIE1000Unsigned16 (1..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "The policy VLAN ID. Only valid when policy 'Tagged' is TRUE" ::= { cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry 8 } cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoL2Priority OBJECT-TYPE SYNTAX CIE1000Unsigned8 (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the LLDP neighbor's policy L2 priority." ::= { cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry 9 } cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoDscp OBJECT-TYPE SYNTAX CIE1000Unsigned8 (0..63) MAX-ACCESS read-only STATUS current DESCRIPTION "LLDP policy DSCP." ::= { cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry 10 } cie1000LldpControl OBJECT IDENTIFIER ::= { cie1000LldpMibObjects 4 } cie1000LldpControlStatisticsClear OBJECT IDENTIFIER ::= { cie1000LldpControl 1 } cie1000LldpControlStatisticsClearTable OBJECT-TYPE SYNTAX SEQUENCE OF CIE1000LldpControlStatisticsClearEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is a table to clear LLDP statistics for a specific interface." ::= { cie1000LldpControlStatisticsClear 1 } cie1000LldpControlStatisticsClearEntry OBJECT-TYPE SYNTAX CIE1000LldpControlStatisticsClearEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each interface has a set of statistics counters" INDEX { cie1000LldpControlStatisticsClearIfIndex } ::= { cie1000LldpControlStatisticsClearTable 1 } CIE1000LldpControlStatisticsClearEntry ::= SEQUENCE { cie1000LldpControlStatisticsClearIfIndex CIE1000InterfaceIndex, cie1000LldpControlStatisticsClearStatisticsClear TruthValue } cie1000LldpControlStatisticsClearIfIndex OBJECT-TYPE SYNTAX CIE1000InterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Logical interface number index." ::= { cie1000LldpControlStatisticsClearEntry 1 } cie1000LldpControlStatisticsClearStatisticsClear OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Set to TRUE to clear the LLDP statistics of an interface." ::= { cie1000LldpControlStatisticsClearEntry 2 } cie1000LldpControlStatisticsClearGlobal OBJECT IDENTIFIER ::= { cie1000LldpControlStatisticsClear 2 } cie1000LldpControlStatisticsClearGlobalClear OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Set to TRUE to clear the LLDP global statistics." ::= { cie1000LldpControlStatisticsClearGlobal 1 } cie1000LldpMibConformance OBJECT IDENTIFIER ::= { cie1000LldpMib 2 } cie1000LldpMibCompliances OBJECT IDENTIFIER ::= { cie1000LldpMibConformance 1 } cie1000LldpMibGroups OBJECT IDENTIFIER ::= { cie1000LldpMibConformance 2 } cie1000LldpConfigGlobalInfoGroup OBJECT-GROUP OBJECTS { cie1000LldpConfigGlobalReInitDelay, cie1000LldpConfigGlobalMsgTxHold, cie1000LldpConfigGlobalMsgTxInterval, cie1000LldpConfigGlobalTxDelay } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000LldpMibGroups 1 } cie1000LldpConfigInfoGroup OBJECT-GROUP OBJECTS { cie1000LldpConfigIfIndex, cie1000LldpConfigAdminState, cie1000LldpConfigCdpAware, cie1000LldpConfigOptionalTlvs, cie1000LldpConfigSnmpNotificationEna } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000LldpMibGroups 2 } cie1000LldpConfigMedInfoGroup OBJECT-GROUP OBJECTS { cie1000LldpConfigMedIfIndex, cie1000LldpConfigMedOptionalTlvs, cie1000LldpConfigMedDeviceType } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000LldpMibGroups 3 } cie1000LldpConfigMedPolicyInfoGroup OBJECT-GROUP OBJECTS { cie1000LldpConfigMedPolicyLldpmedPolicy, cie1000LldpConfigMedPolicyApplicationType, cie1000LldpConfigMedPolicyTagged, cie1000LldpConfigMedPolicyVlanId, cie1000LldpConfigMedPolicyL2Priority, cie1000LldpConfigMedPolicyDscp, cie1000LldpConfigMedPolicyAction } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000LldpMibGroups 4 } cie1000LldpConfigMedPolicyListInfoGroup OBJECT-GROUP OBJECTS { cie1000LldpConfigMedPolicyListIfIndex, cie1000LldpConfigMedPolicyListLldpmedPolicy, cie1000LldpConfigMedPolicyListLldpmedPoliciesList } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000LldpMibGroups 5 } cie1000LldpConfigMedGlobalInfoGroup OBJECT-GROUP OBJECTS { cie1000LldpConfigMedGlobalFastRepeatCount, cie1000LldpConfigMedGlobalLatitude, cie1000LldpConfigMedGlobalLongitude, cie1000LldpConfigMedGlobalAltitudeType, cie1000LldpConfigMedGlobalAltitude, cie1000LldpConfigMedGlobalElinAddr, cie1000LldpConfigMedGlobalDatum, cie1000LldpConfigMedGlobalCountryCode } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000LldpMibGroups 6 } cie1000LldpConfigMedLocationInfInfoGroup OBJECT-GROUP OBJECTS { cie1000LldpConfigMedLocationInfLldpmedIndex, cie1000LldpConfigMedLocationInfCivicAddress } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000LldpMibGroups 7 } cie1000LldpConfigMedPolicyRowEditorInfoGroup OBJECT-GROUP OBJECTS { cie1000LldpConfigMedPolicyRowEditorLldpmedPolicy, cie1000LldpConfigMedPolicyRowEditorApplicationType, cie1000LldpConfigMedPolicyRowEditorTagged, cie1000LldpConfigMedPolicyRowEditorVlanId, cie1000LldpConfigMedPolicyRowEditorL2Priority, cie1000LldpConfigMedPolicyRowEditorDscp, cie1000LldpConfigMedPolicyRowEditorAction } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000LldpMibGroups 8 } cie1000LldpStatusStatisticsGlobalCountersInfoGroup OBJECT-GROUP OBJECTS { cie1000LldpStatusStatisticsGlobalCountersTableInserts, cie1000LldpStatusStatisticsGlobalCountersTableDeletes, cie1000LldpStatusStatisticsGlobalCountersTableDrops, cie1000LldpStatusStatisticsGlobalCountersTableAgeOuts, cie1000LldpStatusStatisticsGlobalCountersLastChangeTime } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000LldpMibGroups 9 } cie1000LldpStatusStatisticsTableInfoGroup OBJECT-GROUP OBJECTS { cie1000LldpStatusStatisticsIfIndex, cie1000LldpStatusStatisticsTxTotal, cie1000LldpStatusStatisticsRxTotal, cie1000LldpStatusStatisticsRxError, cie1000LldpStatusStatisticsRxDiscarded, cie1000LldpStatusStatisticsTLVsDiscarded, cie1000LldpStatusStatisticsTLVsUnrecognized, cie1000LldpStatusStatisticsTLVsOrgDiscarded, cie1000LldpStatusStatisticsAgeOuts } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000LldpMibGroups 10 } cie1000LldpStatusNeighborsInfInfoGroup OBJECT-GROUP OBJECTS { cie1000LldpStatusNeighborsInfIfIndex, cie1000LldpStatusNeighborsInfLldpmedIndex, cie1000LldpStatusNeighborsInfChassisId, cie1000LldpStatusNeighborsInfPortId, cie1000LldpStatusNeighborsInfPortDescription, cie1000LldpStatusNeighborsInfSystemName, cie1000LldpStatusNeighborsInfSystemDescription, cie1000LldpStatusNeighborsInfSystemCapabilities, cie1000LldpStatusNeighborsInfSystemCapabilitiesEnable } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000LldpMibGroups 11 } cie1000LldpStatusNeighborsMgmtInfInfoGroup OBJECT-GROUP OBJECTS { cie1000LldpStatusNeighborsMgmtInfIfIndex, cie1000LldpStatusNeighborsMgmtInfLldpmedIndex, cie1000LldpStatusNeighborsMgmtInfLldpManagement, cie1000LldpStatusNeighborsMgmtInfSystemMgmAddressSubtype, cie1000LldpStatusNeighborsMgmtInfSystemMgmtAddress, cie1000LldpStatusNeighborsMgmtInfSystemMgmtInterfaceSubtype, cie1000LldpStatusNeighborsMgmtInfSystemMgmtInterface, cie1000LldpStatusNeighborsMgmtInfSystemMgmtOid } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000LldpMibGroups 12 } cie1000LldpStatusMedRemoteDeviceInfoInfoGroup OBJECT-GROUP OBJECTS { cie1000LldpStatusMedRemoteDeviceInfoIfIndex, cie1000LldpStatusMedRemoteDeviceInfoLldpmedIndex, cie1000LldpStatusMedRemoteDeviceInfoCapabilities, cie1000LldpStatusMedRemoteDeviceInfoCapabilitiesEnabled, cie1000LldpStatusMedRemoteDeviceInfoLatitude, cie1000LldpStatusMedRemoteDeviceInfoLongitude, cie1000LldpStatusMedRemoteDeviceInfoAltitudeType, cie1000LldpStatusMedRemoteDeviceInfoAltitude, cie1000LldpStatusMedRemoteDeviceInfoDatum, cie1000LldpStatusMedRemoteDeviceInfoElinaddr, cie1000LldpStatusMedRemoteDeviceInfoDeviceType, cie1000LldpStatusMedRemoteDeviceInfoHwRev, cie1000LldpStatusMedRemoteDeviceInfoFwRev, cie1000LldpStatusMedRemoteDeviceInfoSwRev, cie1000LldpStatusMedRemoteDeviceInfoSerialNo, cie1000LldpStatusMedRemoteDeviceInfoManufacturerName, cie1000LldpStatusMedRemoteDeviceInfoModelName, cie1000LldpStatusMedRemoteDeviceInfoAssetId, cie1000LldpStatusMedRemoteDeviceInfoEeeRxTwSys, cie1000LldpStatusMedRemoteDeviceInfoEeeTxTwSys, cie1000LldpStatusMedRemoteDeviceInfoEeeFbTwSys, cie1000LldpStatusMedRemoteDeviceInfoEeeTxTwSysEcho, cie1000LldpStatusMedRemoteDeviceInfoEeeRxTwSysEcho } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000LldpMibGroups 13 } cie1000LldpStatusMedRemoteDeviceLocInfoInfoGroup OBJECT-GROUP OBJECTS { cie1000LldpStatusMedRemoteDeviceLocInfoIfIndex, cie1000LldpStatusMedRemoteDeviceLocInfoLldpmedIndex, cie1000LldpStatusMedRemoteDeviceLocInfoState, cie1000LldpStatusMedRemoteDeviceLocInfoCounty, cie1000LldpStatusMedRemoteDeviceLocInfoCity, cie1000LldpStatusMedRemoteDeviceLocInfoDistrict, cie1000LldpStatusMedRemoteDeviceLocInfoBlock, cie1000LldpStatusMedRemoteDeviceLocInfoStreet, cie1000LldpStatusMedRemoteDeviceLocInfoLeadingStreetDirection, cie1000LldpStatusMedRemoteDeviceLocInfoTrailingStreetSuffix, cie1000LldpStatusMedRemoteDeviceLocInfoStreetSuffix, cie1000LldpStatusMedRemoteDeviceLocInfoHouseNo, cie1000LldpStatusMedRemoteDeviceLocInfoHouseNoSuffix, cie1000LldpStatusMedRemoteDeviceLocInfoLandmark, cie1000LldpStatusMedRemoteDeviceLocInfoAdditionalInfo, cie1000LldpStatusMedRemoteDeviceLocInfoName, cie1000LldpStatusMedRemoteDeviceLocInfoZipCode, cie1000LldpStatusMedRemoteDeviceLocInfoBuilding, cie1000LldpStatusMedRemoteDeviceLocInfoApartment, cie1000LldpStatusMedRemoteDeviceLocInfoFloor, cie1000LldpStatusMedRemoteDeviceLocInfoRoomNumber, cie1000LldpStatusMedRemoteDeviceLocInfoPlaceType, cie1000LldpStatusMedRemoteDeviceLocInfoPostalCommunityName, cie1000LldpStatusMedRemoteDeviceLocInfoPoBox, cie1000LldpStatusMedRemoteDeviceLocInfoAdditionalCode, cie1000LldpStatusMedRemoteDeviceLocInfoCountryCode } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000LldpMibGroups 14 } cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoInfoGroup OBJECT-GROUP OBJECTS { cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoIfIndex, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoLldpmedIndex, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoLldpmedPolicy, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoApplicationType, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoUnknownPolicy, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoTagged, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoVlanId, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoL2Priority, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoDscp } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000LldpMibGroups 15 } cie1000LldpControlStatisticsClearTableInfoGroup OBJECT-GROUP OBJECTS { cie1000LldpControlStatisticsClearIfIndex, cie1000LldpControlStatisticsClearStatisticsClear } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000LldpMibGroups 16 } cie1000LldpControlStatisticsClearGlobalInfoGroup OBJECT-GROUP OBJECTS { cie1000LldpControlStatisticsClearGlobalClear } STATUS current DESCRIPTION "A collection of objects." ::= { cie1000LldpMibGroups 17 } cie1000LldpMibCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the implementation." MODULE -- this module MANDATORY-GROUPS { cie1000LldpConfigGlobalInfoGroup, cie1000LldpConfigInfoGroup, cie1000LldpConfigMedInfoGroup, cie1000LldpConfigMedPolicyInfoGroup, cie1000LldpConfigMedPolicyListInfoGroup, cie1000LldpConfigMedGlobalInfoGroup, cie1000LldpConfigMedLocationInfInfoGroup, cie1000LldpConfigMedPolicyRowEditorInfoGroup, cie1000LldpStatusStatisticsGlobalCountersInfoGroup, cie1000LldpStatusStatisticsTableInfoGroup, cie1000LldpStatusNeighborsInfInfoGroup, cie1000LldpStatusNeighborsMgmtInfInfoGroup, cie1000LldpStatusMedRemoteDeviceInfoInfoGroup, cie1000LldpStatusMedRemoteDeviceLocInfoInfoGroup, cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoInfoGroup, cie1000LldpControlStatisticsClearTableInfoGroup, cie1000LldpControlStatisticsClearGlobalInfoGroup } ::= { cie1000LldpMibCompliances 1 } END