-- -- WAN-MIB.my -- MIB generated by MG-SOFT Visual MIB Builder Version 3.0 Build 253 -- Thursday, June 09, 2005 at 17:41:48 -- -- WAN-MIB.mib -- -- ======================================================== -- SourceSafe Version Information: -- $Revision: 29 $ -- Check in $Date: 21/06/05 11:24a $ -- $Author: Dgluskin $ -- $Archive: /MIBs/Version 1.0/Source/Avaya/WAN-MIB.MY $ -- ======================================================== -- Copyright 2002 AVAYA, inc. -- All Rights Reserved. -- -- Reproduction of this document is authorized on condition -- that the foregoing copyright notice is included. -- -- This AVAYA SNMP Management Information Base Specification -- (Specification) embodies AVAYA confidential and -- Proprietary intellectual property. AVAYA retains all -- Title and ownership in the Specification, including any revisions -- It is AVAYA's intent to encourage the widespread use of this -- Specification in connection with the management of AVAYA products. -- AVAYA grants vendors, end-users, and other interested parties -- a non-exclusive license to use this Specification in connection -- with the management of AVAYA products. -- -- This Specification is supplied "as is," and AVAYA makes -- no warranty, either express or implied, as to the use, -- operation, condition, or performance of the Specification. -- ======================================================== WAN-MIB DEFINITIONS ::= BEGIN IMPORTS lsg FROM AVAYAGEN-MIB dsx0BundleIndex, dsx0BundleIfIndex, dsx0BundleCircuitIdentifier, dsx0BundleRowStatus FROM DS0BUNDLE-MIB DLCI FROM FRAME-RELAY-DTE-MIB ifIndex, ifAdminStatus, ifOperStatus, ifName, ifAlias, InterfaceIndex FROM IF-MIB PhysAddress FROM RFC1213-MIB OBJECT-GROUP, MODULE-COMPLIANCE FROM SNMPv2-CONF IpAddress, Integer32, Unsigned32, Gauge32, OBJECT-TYPE, MODULE-IDENTITY FROM SNMPv2-SMI DisplayString, RowStatus, TEXTUAL-CONVENTION FROM SNMPv2-TC; -- REVISION "0506210920Z" @@ June 21, 2005 at 09:20 GMT -- "Version 2.1.12 - Dan Gluskin -- Add ifTableXtndType for modem type setting -- November 03, 2004 at 08:00 -- REVISION "0504141644Z" @@ April 14, 2005 at 16:44 GMT -- "Version 2.1.11 - Shlomi Biton -- Adding explanation to frameRelayNonIetf enumeration in the ifTableXtndEncapsulation." -- REVISION "0503201531Z" @@ Mar 21, 2005 at 15:31 GMT -- "Version 2.1.10 - Shlomi Biton -- Adding loopback to the ifTableXtndOperStatus description. -- Adding frameRelayNonIetf enumeration to the ifTableXtndEncapsulation." -- REVISION "0412221908Z" @@ December 22, 2004 at 19:08 GMT -- "Version 2.1.9 - Shlomi Biton -- Updating ifTableXtndKeepaliveTrackId default value to 'ffffffff'h" -- REVISION "0412121802Z" @@ December 12, 2004 at 18:02 GMT -- "Version 2.1.8 - Shlomi Biton -- Adding notSupported value to ifTableXtndKeepaliveTrackId for interface that track can not -- activated on." -- REVISION "0410121326Z" @@ November 03, 2004 at 08:00 GMT -- "Version 2.1.7 - Shlomi Biton -- Add ifTableXtndKeepaliveTrackId for activating track on specific interfaces." -- REVISION "0410121326Z" @@ October 12th, 2004 at 13:27 GMT -- "Version 2.1.6 - Shlomi Biton -- fix the ifTableXtndPppIpcpDnsOptionRequest definition." -- REVISION "0410101200Z" @@ October 10th, 2004 at 12:00 GMT -- "Version 2.1.5 - Dan Gluskin -- add 'wanDialerPersistentInitial' for dialer persistent initial delay" -- REVISION "0410040830Z" @@ October 04, 2004 at 08:30 GMT -- "Version 2.1.4 - Shlomi Biton -- 1. Adding to ifTableXtndTable the ifTableXtndPppIpcpDnsOptionRequest - -- PPP-IPCP DNS option request " -- REVISION "0409270715Z" @@ September 27st, 2004 at 07:15 GMT -- "Version 2.1.3 - Dan Gluskin -- 1. modem enums added to ifTableXtndOperStatus -- 2. ifTableXtndConfString added " -- REVISION "0409011245Z" @@ September 1st, 2004 at 12:45 GMT -- "Version 2.1.2 - Dan Gluskin -- Remove the wanDialerPreemptive item " -- REVISION "0408261433Z" @@ August 26, 2004 at 14:33 GMT -- "Version 2.1.1 - Dan Gluskin -- Move 'wanDialer under ifs' -- REVISION "0407050540Z" @@ August 22, 2004 at 15:10 GMT -- "Version 2.1.0 - Dan Gluskin -- Add wanDialer group" -- REVISION "0407050540Z" @@ July 5, 2004 at 05:40 GMT -- "Version 2.0.18 - Dan Gluskin -- add an ifTableXtndMinPmtu item" -- REVISION "0406210910Z" @@ June 21, 2004 at 09:10 GMT -- "Version 2.0.17 - Dan Gluskin -- ifTableXtndIpSecDfBit should be read only" -- REVISION "0405231700Z" @@ May 23, 2004 at 17:00 GMT -- "Ver 2.0.16 - Dan Gluskin -- add ifTableXtndIpSecDfBit" -- REVISION "0404151700Z" @@ Mer 15, 2004 at 17:00 GMT -- "Ver 2.0.15 - Dan Gluskin' -- add 'pppoe' and 'arpa' enums to IfTableXtndEncapsulation" -- -- REVISION "0402091001Z" @@ Feb 09, 2004 at 10:01 GMT -- DESCRIPTION -- "Ver 2.0.14 - Shlomi Biton -- Changing keepalive element names to xtndKeepAlive. -- Changing keepAliveDown status to xtndKeepAliveDown" -- REVISION "0311171004Z" @@ November 17, 2003 at 10:04 GMT -- DESCRIPTION -- "Ver 2.0.13 - Shlomi Biton -- Add Health Check Table -- Add new value for ifTableXtndOperStatus of keepAlive Down -- Add new Item to ifTableXtndEntry of ifTableXtndCommonApplifStatus for PBR -- Supporting next hop Interface -- REVISION "0311091431Z" @@ November 9, 2003 at 14:31 GMT -- DESCRIPTION -- "Ver 2.0.12 - Dan Gluskin -- change ifTableXtndVoIPQueue syntax to integer and add fairQ enumeration" -- REVISION "1210031441Z" @@ October 22, 2003 at 14:41 GMT -- DESCRIPTION -- "Ver 2.0.11 - Dan Gluskin -- Add dynamic CAC entries: -- ifTableXtndCacBBL -- ifTableXtndCacPriority -- ifTableXtndCacifStatus" -- REVISION "1007031541Z" @@ July 10, 2003 at 15:41 GMT -- DESCRIPTION -- "Ver 2.0.10 - Dan Gluskin -- Add ds1CurrentDeviceMode" -- REVISION "0211021041Z" @@ November 02, 2002 at 10:41 GMT -- DESCRIPTION -- "Ver 2.0.9 - Dan Gluskin -- ======================== -- Add Interface Traffic-Shaper items to ifTableXtnd" -- REVISION "0208011941Z" @@ August 01, 2002 at 19:41 GMT -- DESCRIPTION -- "Ver 2.0.8 - ItaiZ -- ================= -- backup Delays ranges -- modified to be in -1..3600 range. -- " -- REVISION "0207231140Z" @@ July 23, 2002 at 11:40 GMT -- DESCRIPTION -- "Ver 2.0.7 - Itai Z. -- =================== -- 1. Removed ifTableXtndBackupTrigger. -- Note that the next item OID was chaned as well. -- 2. Range restriction removed from backupEnable, disable delays. -- 'Never' can be modeled as MAXINT. -- 3. Added new serial Line items: -- ifTableXtndCarrierDelay -- ifTableXtndDtrRestartDelay -- ifTableXtndDtrPulseTime -- 4. Added average load and bit rate -- counters & config parameter: -- ifTableXtndLoadInterval -- ifTableXtndInputRate -- ifTableXtndOutputRate -- ifTableXtndInputLoad -- ifTableXtndOutputLoad -- ifTableXtndReliability -- -- -- -- -- " -- REVISION "0206271532Z" @@ June 27, 2002 at 15:32 GMT -- DESCRIPTION -- "Version 2.0.6 - Itai Z. -- ======================= -- 1. Fix ifTableXtndOperStatus - added back the adminDown value." -- REVISION "0206261405Z" @@ June 26, 2002 at 14:05 GMT -- DESCRIPTION -- "Version 2.0.5 - ItaiZ -- ===================== -- 1. frStaticCircuitDLCIrole - description & enaums have changed. -- 2. frStaticCircuitPriorityClass removed." -- REVISION "0206251441Z" @@ June 25, 2002 at 14:41 GMT -- DESCRIPTION -- "Version 2.0.4 - ItaiZ -- ===================== -- 1. Added Avaya Boiler plate -- 2. frStaticCircuitTable modified -- to include frStaticDLCIrole -- as index. This provides -- the ability to map DLCIs to -- priority-sets. The index -- enforce DLCI creation/deletion -- restrictions. -- 3. Added ifTableXtndBackupCapabilities, -- ifTableXtndBackupIf, -- ifTableXtndBackupEnableDelay, -- ifTableXtndBackupDisableDelay, -- ifTableXtndBackupTrigger and -- ifTableXtndPrimaryIf to support backup -- interfaces. -- 4. ifTablXtndOperStatus has another value - -- dormantDown to reflect backup Interface in dormant -- state. -- -- " -- REVISION "0206121108Z" @@ June 12, 2002 at 11:08 GMT -- DESCRIPTION -- "Version 2.0.3 - ItaiZ -- ===================== -- 1. frStatiCircuitLFI removed. -- LFI will be controlled via -- a frame relay map-class MIB, -- when defined. -- 2. Description of ifTableXtndBandwidth -- explicitly says that the units are Kbps -- " -- REVISION "0206061550Z" @@ June 06, 2002 at 15:50 GMT -- DESCRIPTION -- "Version 2.0.2 - Itai Z. -- -- 1. frStaticCircuitPriorityClasss -- is now read only, and has -- two more values to represent possible -- values assigned through CLI -- 2. ifTableXtendOperStatus explained in -- pseudo code" -- REVISION "0205291903Z" @@ May 29, 2002 at 19:03 GMT -- DESCRIPTION -- "Version 2.0.1 - Itai Z. -- 1. Changed name & definition of frCircuitXtendTable -- to frStaticCircuitTable.This table is now used to create and delete -- Static DLCIs. -- 2. ifTableXtndOperStatus defined -- " -- REVISION "0205281910Z" @@ May 28, 2002 at 19:10 GMT -- DESCRIPTION -- "Version 2.0.0 - Itai Zilbershtein -- Added support for Frame Relay and Universal Serial Ports -- For X330WAN V1.5" -- REVISION "0203051047Z" @@ March 05, 2002 at 10:47 GMT -- DESCRIPTION -- "Version 1.0 - Michael W. -- Keepalive added." -- REVISION "0203041042Z" @@ March 04, 2002 at 10:42 GMT -- DESCRIPTION -- "Version 0.4 - Michael W. -- Added description, cablelength and gain -- extensions to ifTable." -- REVISION "0202241242Z" @@ February 24, 2002 at 12:42 GMT -- DESCRIPTION -- "Version 0.3 - Michael W. -- Added the ifTableXtndTable -- Added speed factor per ds0bundle" -- REVISION "0112191015Z" @@ December 19, 2001 at 10:15 GMT -- DESCRIPTION -- "Version 0.2 - Michael W. -- Added the ds0BundleMembers table -- to override the ifStack. -- ifStack usage will be deferred to -- a later version, at which time the -- ds0BundleMembers mib will become -- obsolete. -- " -- REVISION "0112061045Z" @@ December 06, 2001 at 10:45 GMT -- DESCRIPTION -- "Version 0.1 - Michael Weksler: -- First SMIv2 version -- -- " avayaEISWan MODULE-IDENTITY LAST-UPDATED "0506210920Z" -- June 21, 2005 at 09:20 GMT ORGANIZATION "Avaya Inc." CONTACT-INFO "Dan Gluskin, Avaya Inc. +972-3-6457561 mailto:dgluskin@avaya.com Itai Zilbershtein, Avaya Inc. +972 3 6457667 mailto:izilbers@avaya.com" DESCRIPTION "The mib for controlling WAN-related features of WAN access devices." ::= { lsg 6 } -- -- Textual conventions -- -- Textual conventions -- OnOff ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This textual convention describes a feature that can be either turned on, off or is not relevant for an object." SYNTAX INTEGER { on(1), off(2), notRelevant(255) } -- -- Node definitions -- -- Node definitions -- -- 1.3.6.1.4.1.6889.2.1.6.1 -- 1.3.6.1.4.1.6889.2.1.6.1 deviceSpecific OBJECT IDENTIFIER ::= { avayaEISWan 1 } -- 1.3.6.1.4.1.6889.2.1.6.1.1 -- 1.3.6.1.4.1.6889.2.1.6.1.1 x330wanSpecific OBJECT IDENTIFIER ::= { deviceSpecific 1 } -- 1.3.6.1.4.1.6889.2.1.6.1.1.1 -- 1.3.6.1.4.1.6889.2.1.6.1.1.1 intWanPortTable OBJECT-TYPE SYNTAX SEQUENCE OF IntWanPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Internal Wan Port configuration table. Each entry in the table specifies the configuration of an internal port, connecting the WAN blade to the host switch." ::= { x330wanSpecific 1 } -- 1.3.6.1.4.1.6889.2.1.6.1.1.1.1 -- 1.3.6.1.4.1.6889.2.1.6.1.1.1.1 intWanPortEntry OBJECT-TYPE SYNTAX IntWanPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of port configuration entries." INDEX { intWanGroupID, intWanPortID } ::= { intWanPortTable 1 } IntWanPortEntry ::= SEQUENCE { intWanGroupID INTEGER, intWanPortID INTEGER, intWanPortSpeed INTEGER, intWanPortMode INTEGER, intWanPortAutoNegotiation INTEGER, intWanPortVLANMode INTEGER, intWanPortVLANBindingMode INTEGER, intWanPortVlanList OCTET STRING } -- 1.3.6.1.4.1.6889.2.1.6.1.1.1.1.1 -- 1.3.6.1.4.1.6889.2.1.6.1.1.1.1.1 intWanGroupID OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The Id of the group in which the port to be configured resides." ::= { intWanPortEntry 1 } -- 1.3.6.1.4.1.6889.2.1.6.1.1.1.1.2 -- 1.3.6.1.4.1.6889.2.1.6.1.1.1.1.2 intWanPortID OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The Id of the port to be configured." ::= { intWanPortEntry 2 } -- 1.3.6.1.4.1.6889.2.1.6.1.1.1.1.3 -- 1.3.6.1.4.1.6889.2.1.6.1.1.1.1.3 intWanPortSpeed OBJECT-TYPE SYNTAX INTEGER { ethernet(1), fastEthernet(2), notSupported(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter defines the port speed: ethernet(1) and fastEthernet(2)." DEFVAL { fastEthernet } ::= { intWanPortEntry 3 } -- 1.3.6.1.4.1.6889.2.1.6.1.1.1.1.4 -- 1.3.6.1.4.1.6889.2.1.6.1.1.1.1.4 intWanPortMode OBJECT-TYPE SYNTAX INTEGER { halfDuplex(1), fullDuplexSymPause(7), notSupported(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "The flow control mode of the port when operated in full duplex: halfDuplex(1) - Half duplex connection, standard mode for segment fullDuplexNoPause(2) - Full duplex connection without exchanging flow control packets fullDuplexProprietaryFC(3) - Full duplex connection with AVAYA's proprietary flow control frames exchanged fullDuplexISL(4) - Full duplex connection with ISL proprietary protocol control words for VLAN & priority exchanged, ISL = Inter-Switch-Link fullDuplexFlowControlISL(5) - Full duplex connection with both ISL proprietary protocol control words and flow control frames exchanged fullDuplexAsymTxPause(6) - Full duplex connection with STD 802.3x flow control frames sent from this port, but flow control packets received on it are not processed fullDuplexSymPause(7) - Full duplex connection with STD 802.3x flow control frames exchanged fullDuplexAsymRxPause(8) - Full duplex connection with no flow control frames sent from this port, but STD 802.3x flow control 0frames received on it are processed. For Giga ports, when auto-negotiation is enabled, the flow control mode is set internally according to auto-negotiation resolution; and access to this item is read-only." DEFVAL { fullDuplexSymPause } ::= { intWanPortEntry 4 } -- 1.3.6.1.4.1.6889.2.1.6.1.1.1.1.5 -- 1.3.6.1.4.1.6889.2.1.6.1.1.1.1.5 intWanPortAutoNegotiation OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2), notSupported(255) } MAX-ACCESS read-write STATUS current DESCRIPTION " This object define if the Auto Sense /Auto Negotiation process is enable(1) or disable (2) for modules that don't support the Auto Snese mode please define the notSupported option.." DEFVAL { disable } ::= { intWanPortEntry 5 } -- 1.3.6.1.4.1.6889.2.1.6.1.1.1.1.6 -- 1.3.6.1.4.1.6889.2.1.6.1.1.1.1.6 intWanPortVLANMode OBJECT-TYPE SYNTAX INTEGER { perPortOnly(1), dot1QTagging(2), notSupported(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "This item defines the VLAN operation mode of the port: perPortOnly(1) - indicates that all received packets are mapped to the VLAN, defined on the port, and packets are transmitted in untagged format; dot1QTagging(2) - indicates that all received packets are mapped to VLANs according to 802.1Q standard. All transmitted packets are tagged according to the standard 802.1Q tagging; plusTagging(3) - indicates that all packets recieved and transmitted on that port are tagged according to Lannet_s PlusTagging scheme. This mode is used when inter-VLAN bridging should be supported; islTagging(4) - indicates that all packets recieved and transmitted on that port are tagged according to the proprietary ISL mode of Lannet; dot1QTaggingButPVID(5) - indicates that all received packets are mapped to VLANs according to 802.1Q standard. All transmitted packets are tagged according to the standard 802.1Q tagging, exluding packets that belong to the port_s VLAN,which are transmitted untagged." DEFVAL { dot1QTagging } ::= { intWanPortEntry 6 } -- 1.3.6.1.4.1.6889.2.1.6.1.1.1.1.7 -- 1.3.6.1.4.1.6889.2.1.6.1.1.1.1.7 intWanPortVLANBindingMode OBJECT-TYPE SYNTAX INTEGER { static(1), bindToReceive(2), bindToAll(3), notSupported(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "VLAN binding mode assigned to this port. static - this port supports only the egress VLAN list as configured manually in its corresponding dot1qVlanStaticEgressPort. This is the default VLAN Binding mode. bindToReceive - this port supports the whole range of 3K VLANs from VLAN ID 1 to 3071. bindToAll - this port supports the egress VLAN IDs for which dot1qVlanStaticTable rows exist. GVRP - this port supports the egress VLAN IDs configured manually in its corresponding dot1qVlanStaticEgressPort as well as VLAN IDs requested by the GVRP link partner." DEFVAL { static } ::= { intWanPortEntry 7 } -- 1.3.6.1.4.1.6889.2.1.6.1.1.1.1.8 -- 1.3.6.1.4.1.6889.2.1.6.1.1.1.1.8 intWanPortVlanList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "An 4096-bit-long bitmask of all vlans supported on a port. For example: A 1 bit in the 10th place means that vlan 10 is supported." ::= { intWanPortEntry 8 } -- 1.3.6.1.4.1.6889.2.1.6.1.1.2 -- 1.3.6.1.4.1.6889.2.1.6.1.1.2 ds0BundleMemmbersTable OBJECT-TYPE SYNTAX SEQUENCE OF Ds0BundleMemmbersEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to quickly assign members to a ds0Bunbdle Its effect is similar as using the ifStack table, only it does it in one go. " ::= { x330wanSpecific 2 } -- 1.3.6.1.4.1.6889.2.1.6.1.1.2.1 -- 1.3.6.1.4.1.6889.2.1.6.1.1.2.1 ds0BundleMemmbersEntry OBJECT-TYPE SYNTAX Ds0BundleMemmbersEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in yhr ds0BundleMembers table" INDEX { dsx0BundleIndex } ::= { ds0BundleMemmbersTable 1 } Ds0BundleMemmbersEntry ::= SEQUENCE { ds0BundleMemmbersList OCTET STRING, ds0BundleSpeedFactor INTEGER } -- 1.3.6.1.4.1.6889.2.1.6.1.1.2.1.1 -- 1.3.6.1.4.1.6889.2.1.6.1.1.2.1.1 ds0BundleMemmbersList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "A bit mask of timeslots that are part of the channel group identified by ds0BundleIndex. First (leftmost) bit stands for timeslot 0." DEFVAL { '00'h } ::= { ds0BundleMemmbersEntry 1 } -- 1.3.6.1.4.1.6889.2.1.6.1.1.2.1.2 -- 1.3.6.1.4.1.6889.2.1.6.1.1.2.1.2 ds0BundleSpeedFactor OBJECT-TYPE SYNTAX INTEGER { a64kbps(1), a56kbps(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The speed factor for this ds0bundle. This can either be 56k or 64k." ::= { ds0BundleMemmbersEntry 2 } -- Interfaces specific objects -- -- 1.3.6.1.4.1.6889.2.1.6.2 -- 1.3.6.1.4.1.6889.2.1.6.2 ifs OBJECT IDENTIFIER ::= { avayaEISWan 2 } -- 1.3.6.1.4.1.6889.2.1.6.2.1 -- 1.3.6.1.4.1.6889.2.1.6.2.1 ds1objs OBJECT IDENTIFIER ::= { ifs 1 } -- 1.3.6.1.4.1.6889.2.1.6.2.1.1 -- 1.3.6.1.4.1.6889.2.1.6.2.1.1 ds1DeviceMode OBJECT-TYPE SYNTAX INTEGER { e1(1), t1(2), j1(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The configured device mode. Either all DS1s on the device are e1, t1 or j1. To activate a new selection, perform 'copy running-config startup-config' and reset the device." ::= { ds1objs 1 } -- 1.3.6.1.4.1.6889.2.1.6.2.1.1 -- 1.3.6.1.4.1.6889.2.1.6.2.1.2 ds1CurrentDeviceMode OBJECT-TYPE SYNTAX INTEGER { e1(1), t1(2), j1(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current device mode" ::= { ds1objs 2 } -- 1.3.6.1.4.1.6889.2.1.6.2.2 -- 1.3.6.1.4.1.6889.2.1.6.2.2 ifTablePrivateExtensions OBJECT IDENTIFIER ::= { ifs 2 } -- This table provides additional -- information for interfaces that appear -- in the ifTable. -- 1.3.6.1.4.1.6889.2.1.6.2.2.1 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1 ifTableXtndTable OBJECT-TYPE SYNTAX SEQUENCE OF IfTableXtndEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifTableXtndTable table." ::= { ifTablePrivateExtensions 1 } -- An entry in the ifTableXtndTable. -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1 ifTableXtndEntry OBJECT-TYPE SYNTAX IfTableXtndEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is an extension of the itTable. It contains a row per every row of the ifTable. It is used to perform additional configuration, not available through standard mibs. A row will exist in this table for each row in the ifTable, even if specific configuration object has no meaning for the type of interface for which this row is used." INDEX { ifTableXtndIndex } ::= { ifTableXtndTable 1 } IfTableXtndEntry ::= SEQUENCE { ifTableXtndIndex InterfaceIndex, ifTableXtndPeerAddress IpAddress, ifTableXtndVoIPQueue INTEGER, ifTableXtndCableLength INTEGER, ifTableXtndGain INTEGER, ifTableXtndDescription DisplayString, ifTableXtndKeepAlive Integer32, ifTableXtndMtu Integer32, ifTableXtndInvertTxClock OnOff, ifTableXtndDTELoopback OnOff, ifTableXtndIgnoreDCD OnOff, ifTableXtndIdleChars INTEGER, ifTableXtndBandwidth Integer32, ifTableXtndEncapsulation INTEGER, ifTableXtndOperStatus INTEGER, ifTableXtndBackupCapabilities INTEGER, ifTableXtndBackupIf InterfaceIndex, ifTableXtndBackupEnableDelay INTEGER, ifTableXtndBackupDisableDelay INTEGER, ifTableXtndPrimaryIf InterfaceIndex, ifTableXtndCarrierDelay Integer32, ifTableXtndDtrRestartDelay Integer32, ifTableXtndDtrPulseTime Integer32, ifTableXtndLoadInterval Integer32, ifTableXtndInputRate Gauge32, ifTableXtndOutputRate Gauge32, ifTableXtndInputLoad Gauge32, ifTableXtndOutputLoad Gauge32, ifTableXtndReliability Gauge32, ifTableXtndTrafficShaperRate Integer32, ifTableXtndCacBBL Integer32, ifTableXtndCacPriority Integer32, ifTableXtndCacifStatus INTEGER, ifTableXtndCommonApplifStatus OCTET STRING, ifTableXtndIpSecDfBit INTEGER, ifTableXtndMinPmtu Integer32, ifTableXtndConfString DisplayString, ifTableXtndPppIpcpDnsOptionRequest INTEGER, ifTableXtndKeepaliveTrackId Unsigned32, ifTableXtndFrTrafficShaping OnOff, ifTableXtndType INTEGER } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.1 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.1 ifTableXtndIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index in the ifTable for which this row is providing information." ::= { ifTableXtndEntry 1 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.2 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.2 ifTableXtndPeerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the peer device on the link identified by this ifIndex. This value is only meaningful for point to point links." ::= { ifTableXtndEntry 2 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.3 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.3 ifTableXtndVoIPQueue OBJECT-TYPE SYNTAX INTEGER { on(1), off(2), fairQ(3), notRelevant(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Turns voip-queueing on or off or turn fair-queuing on." DEFVAL { notRelevant } ::= { ifTableXtndEntry 3 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.4 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.4 ifTableXtndCableLength OBJECT-TYPE SYNTAX INTEGER { long15db(1), long22dot5db(2), long7dot5db(3), long0db(4), short133ft(5), short266ft(6), short399ft(7), short533ft(8), short655ft(9), notSupported(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Cable length attenuation on this interface." ::= { ifTableXtndEntry 4 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.5 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.5 ifTableXtndGain OBJECT-TYPE SYNTAX INTEGER { a26(1), a36(2), notSupported(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "The gain on this interface." ::= { ifTableXtndEntry 5 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.6 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.6 ifTableXtndDescription OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This object is a Read-Write equivalent of ifDescr. It is used to enable users to change the value of ifDescr." DEFVAL { ''b } ::= { ifTableXtndEntry 6 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.7 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.7 ifTableXtndKeepAlive OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Time, in seconds, between keepalive messages. 0 means keepalive should not be used, or is not supported." DEFVAL { 0 } ::= { ifTableXtndEntry 7 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.8 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.8 ifTableXtndMtu OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object is a R/W copy of the ifMtu object from the ifTable. It enables changing of the MTU for interfaces that allow this." DEFVAL { 0 } ::= { ifTableXtndEntry 8 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.9 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.9 ifTableXtndInvertTxClock OBJECT-TYPE SYNTAX OnOff MAX-ACCESS read-write STATUS current DESCRIPTION "This object is only applicable for rs232-like synchronuos DTE interefaces. It determines whether the transmit clock is inverted. " DEFVAL { notRelevant } ::= { ifTableXtndEntry 9 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.10 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.10 ifTableXtndDTELoopback OBJECT-TYPE SYNTAX OnOff MAX-ACCESS read-write STATUS current DESCRIPTION "This object is only applicable for rs232-like synchronuos DTE interefaces. It determines the status of the DTE loopback." DEFVAL { notRelevant } ::= { ifTableXtndEntry 10 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.11 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.11 ifTableXtndIgnoreDCD OBJECT-TYPE SYNTAX OnOff MAX-ACCESS read-write STATUS current DESCRIPTION "This object is only applicable for rs232-like synchronuos DTE interefaces. This command configures the serial interface to monitor the DSR/CTS signals, instead of DCD signal, as the line up/down indicator." DEFVAL { notRelevant } ::= { ifTableXtndEntry 11 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.12 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.12 ifTableXtndIdleChars OBJECT-TYPE SYNTAX INTEGER { flag(1), mark(2), space(3), notRelevant(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is only applicable for rs232-like synchronuos DTE interefaces. This command sets the bit pattern used to indicate an idle line." DEFVAL { notRelevant } ::= { ifTableXtndEntry 12 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.13 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.13 ifTableXtndBandwidth OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to determine the bandwidth of the interface, in Kbps, for interfaces that support it. This information is informational, and does not affect the actual transmission rate." DEFVAL { 0 } ::= { ifTableXtndEntry 13 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.14 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.14 ifTableXtndEncapsulation OBJECT-TYPE SYNTAX INTEGER { ppp(1), frameRelay(2), pppoe(3), arpa(4), frameRelayNonIetf(5), notSupported(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Applicable only to layer 1 interfaces. The type of the layer 2 interface on top of this Interface. ppp - The Layer 2 interface is PPP frameRelay - The Layer 2 interface is IETF Frame Relay. pppoe - PPPoE-client mode for Ethernet interfaces arpa - non-PPPoE client mode for Ethernet interfaces frameRelayNonIetf - The Layer 2 interface is Frame Relay compliant with Cisco frame relay but not compliant to IETF. interactive - External Modem enabled (for Console & USB-modem interfaces). terminal - External modem disabled (for Console interface) " DEFVAL { ppp } ::= { ifTableXtndEntry 14 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.15 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.15 ifTableXtndOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), faultDown(2), testing(3), partiallyDownFault(4), adminDown(5), dormantDown(6), xtndKeepAliveDown(7), modemUndetected(8), modemReady(9), modemDialing(10), modemConnectedDialin(11), modemConnectedDialout(12), notSupported(255) } MAX-ACCESS read-only STATUS current DESCRIPTION "An extension to ifOperStatus, for showing faults and partial faliures, including aggregation of upper layer faults (up to but not including L3). The following Pseudo code describes how the MIB value is calculated for different interfaces: if (AdminStatus is down) { XtndOperStatus= adminDown } else if (OperStatus is testing) { XtndOperStatus = testing } else if (This is a backup interface and its currently in dormant state) { XtndOperStatus= dormantDown } else if (OperStatus = down) { XtndOperStatus = faultDown } else switch interface type { case E1/T1: if (XtndOperStatus of any Channel Group over this I/F is (faultDown or partialDownFault)){ XtndOperStatus = partialDownFault } else XtndOperStatus = up break; case USP or Channel Group: if (XtndOperStatus of FR or PPP I/F over this I/F is (faultDown or partialDownFault)){ XtndOperStatus = partialDownFault } else XtndOperStatus = up break; case FastEthernet or loopback: if (XtndKeepAliveStatus is Down) { XtndOperStatus = keepAliveDown } else XtndOperStatus = up break; case PPP or FabricFastEthernet: XtndOperStatus = up break; case Frame Relay: if (XtndOperStatus of any Sub FR over this I/F is (faultDown or partialDownFault)) { XtndOperStatus = partialDownFault } else XtndOperStatus = up break; case Frame Relay Sub I/F: if (at least one DLCI is up, and at least one is down){ XtndOperStatus = partialDownFault } else XtndOperStatus = up break; case Modem: If (modem is undetected) {XtndOperStatus = modemUndetected} elseif (modem is ready to accept calls){XtndOperStatus = modemReady) elseif (a dialer is dialing the modem) {XtndOperStatus = modemDialing} elseif (modem is connected - incoming call) {XtndOperStatus = modemConnectedDialin} elseif (modem is connected - outgoing call) {XtndOperStatus = modemConnectedDialout} } " ::= { ifTableXtndEntry 15 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.16 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.16 ifTableXtndBackupCapabilities OBJECT-TYPE SYNTAX INTEGER { primaryAndBackUp(1), primaryOnly(2), backupOnly(3), notSupported(255) } MAX-ACCESS read-only STATUS current DESCRIPTION "Determines what roles an interface can play in a backup relation. This should be filled per interface, according to its capabilities. primaryAndBackup - the interface can be play both the primary and the backup roles. primaryOnly - the interface can only play the primary role. backupOnly - the interface can only play the backup role. notSupported - the interface can play no role in a backup relation." ::= { ifTableXtndEntry 16 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.17 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.17 ifTableXtndBackupIf OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-write STATUS current DESCRIPTION "The ifIndex of the backup interface for this primary interface. 0 if no backup is defined. The agent will not permit setting this value, if: The intreface is not capable of the primary role, OR The supplied backup index does not point to an interface capable of the backup role, which is not currently in a backup role." DEFVAL { 0 } ::= { ifTableXtndEntry 17 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.18 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.18 ifTableXtndBackupEnableDelay OBJECT-TYPE SYNTAX INTEGER (0..3600) MAX-ACCESS read-write STATUS current DESCRIPTION "The delay (in Secs) that a primary interface must be inactive before its backup interface is activated. Configurable on the primary interface only." ::= { ifTableXtndEntry 18 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.19 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.19 ifTableXtndBackupDisableDelay OBJECT-TYPE SYNTAX INTEGER (-1..3600) MAX-ACCESS read-write STATUS current DESCRIPTION "The delay (in Secs) between the primary coming back to life and its activation and de-activation of its backup interface. The value '-1' means that the primary is never re-activated and the backup is never de-activated. Configurable on the primary interface only." ::= { ifTableXtndEntry 19 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.20 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.20 ifTableXtndPrimaryIf OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "On a backup interface, this will point to the primary interface. '0' means no primary interface." ::= { ifTableXtndEntry 20 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.21 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.21 ifTableXtndCarrierDelay OBJECT-TYPE SYNTAX Integer32 (0..60) MAX-ACCESS read-write STATUS current DESCRIPTION "This command sets the carrier delay on a serial interface in seconds. If a link goes down and comes back up before the carrier delay timer expires, the down state is effectively filtered, and the switch is not aware that a link-down event occurred." DEFVAL { 2 } ::= { ifTableXtndEntry 21 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.22 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.22 ifTableXtndDtrRestartDelay OBJECT-TYPE SYNTAX Integer32 (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "Determines the period in seconds for deactivating DTR signal when the serial line is inactive." DEFVAL { 30 } ::= { ifTableXtndEntry 22 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.23 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.23 ifTableXtndDtrPulseTime OBJECT-TYPE SYNTAX Integer32 (0..60) MAX-ACCESS read-write STATUS current DESCRIPTION "Determines the interval in milliseconds DTR signal is held inactive when the serial line is inactive." DEFVAL { 1 } ::= { ifTableXtndEntry 23 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.24 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.24 ifTableXtndLoadInterval OBJECT-TYPE SYNTAX Integer32 (30..600) MAX-ACCESS read-write STATUS current DESCRIPTION "Determines interval (in secs) for exponential averages calculations for an interface. Must be a multiple of 30." DEFVAL { 300 } ::= { ifTableXtndEntry 24 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.25 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.25 ifTableXtndInputRate OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Expoential Average of the Number of bits received per second calculated for the interval specified in ifTableXtndLoadInterval. The exponentail average smooths peaks while correctly showing current trends. Calculated as follows: RateSample= (bitsLast - bitCurrent)/5 where bitCurrent = number of bits received, sampled every 5 seconds. new_ifTableXtndInputRate = (old_ifTableXtndInputRate - RateSample) *exp( -5/LoadInterval) + RateSample " ::= { ifTableXtndEntry 25 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.26 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.26 ifTableXtndOutputRate OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Expoential Average of the Number of bits sent per second calculated for the interval specified in ifTableXtndLoadInterval. The exponentail average smooths peaks while correctly showing current trends. Calculated as follows: RateSample= (bitsLast - bitCurrent)/5 where bitCurrent = number of bits sent, sampled every 5 seconds. new_ifTableXtndOutputRate = (old_ifTableXtndOutputRate - RateSample) *exp( -5/LoadInterval) + RateSample " ::= { ifTableXtndEntry 26 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.27 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.27 ifTableXtndInputLoad OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Expoential Average of the Input Load calculated for the interval specified in ifTableXtndLoadInterval. Load is expressed a a number in the range 1 to 255. 255 = 100% utilization (input bits per second equal the interface speed). 1 = 0% utilization. The exponentail average smooths peaks while correctly showing current trends. Calculated as follows: RateSample= int((bitsLast - bitCurrent)/(5*ifSpeed))*254 +1 where bitCurrent = number of bits received, sampled every 5 seconds. new_ifTableXtndInputLoad = (old_ifTableXtndInputLoad - RateSample) *exp( -5/LoadInterval) + RateSample " ::= { ifTableXtndEntry 27 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.28 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.28 ifTableXtndOutputLoad OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Expoential Average of the Output Load calculated for the interval specified in ifTableXtndLoadInterval. Load is expressed a a number in the range 1 to 255. 255 = 100% utilization (input bits per second equal the interface speed). 1 = 0% utilization. The exponentail average smooths peaks while correctly showing current trends. Calculated as follows: RateSample= int((bitsLast - bitCurrent)/(5*ifSpeed))*254 +1 where bitCurrent = number of bits sent, sampled every 5 seconds. new_ifTableXtndOutputLoad = (old_ifTableXtndOutputLoad - RateSample) *exp( -5/LoadInterval) + RateSample " ::= { ifTableXtndEntry 28 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.29 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.29 ifTableXtndReliability OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Expoential Average of the Reliability of an interface calculated for the interval specified in ifTableXtndLoadInterval. Reliability is expressed a a number in the range 1 to 255. 255 = Fully Reliable interface. 1 = Interface is extremly un reliable. The exponentail average smooths peaks while correctly showing current trends. RateSample is calculated every 5 seconds as follows: If (OperStatus is down and Admin status is Up) RateSample =1 else RateSample = 255 new_ifTableXtndReliability = (old_ifTableXtndReliability - RateSample) *exp( -5/LoadInterval) + RateSample " ::= { ifTableXtndEntry 29 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.30 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.30 ifTableXtndTrafficShaperRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This item controls a traffic shaper on the interface. Its value is the shaping rate in bits per seconds. When zero, the shaper is disabled" DEFVAL { 0 } ::= { ifTableXtndEntry 30 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.31 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.31 ifTableXtndCacBBL OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Dynamic CAC Bearer Bandwidth Limit in kilo-bits-per-seconds. This item equals -1 when dynamic CAC is not configured." DEFVAL { -1 } ::= { ifTableXtndEntry 31 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.32 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.32 ifTableXtndCacPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "If more than one interface with configured BBL is up, the gateway reports the BBL of the interface with the highest activation priority value. If N active interfaces shares the same highest CAC activation priority. The gateway's RBBL is equals N multiple by the lowest BBL value in this interface group. If the activation priority is unspecified, it receives the default value (5). ." DEFVAL { 5 } ::= { ifTableXtndEntry 32 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.33 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.33 ifTableXtndCacifStatus OBJECT-TYPE SYNTAX INTEGER { notConfigured(1), active(2), notActive(3), activeECMP(4), notSupported(255) } MAX-ACCESS read-only STATUS current DESCRIPTION "Dynamic CAC status of the interface." DEFVAL { notSupported } ::= { ifTableXtndEntry 33 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.34 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.34 ifTableXtndCommonApplifStatus OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Supported Application on this Interface. If 0 value - Not supported else supported. Bit 0 - Unknown Application. Bit 1 - Support of Next Hop Interface in Policy Based Routing Application." ::= { ifTableXtndEntry 34 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.35 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.35 ifTableXtndIpSecDfBit OBJECT-TYPE SYNTAX INTEGER { clear(1), copy(2), notSupported(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "This item controls whether the DF (don't fragment) bit of incoming packets is copied to the external IPSec header" DEFVAL { notSupported } ::= { ifTableXtndEntry 35 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.36 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.36 ifTableXtndMinPmtu OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Set the minimal PMTU for IPSec tunnels." ::= { ifTableXtndEntry 36 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.37 -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.37 ifTableXtndConfString OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "An additional configuration string for the interface. init-string - for modem interfaces " ::= { ifTableXtndEntry 37 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.38 ifTableXtndPppIpcpDnsOptionRequest OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2), notSupported(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "PPP-IPCP DNS option request. Configuration whether during the PPP-IPCP negotiation the DNS option will be requested. Default: Disable. The DNS information gathered will be used by the DNS resolver to resolve hostnames. 1 - enable 2 - disable 255 - notSupported, this Mib item related only to PPP-IPCP interfaces. Other interfaces which are not PPP-IPCP, will return this value." ::= { ifTableXtndEntry 38 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.39 ifTableXtndKeepaliveTrackId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Bind the status of this interface to an object-tracker by specifying the ID of the object-tracker (avstrTrackerId in AVAYA-SAA-TRACK-MIB). A value of 0 means that interface is not bound to any object-tracker. A value of 0xffffffff is notSupported feature for the relevant interface. " DEFVAL { 'ffffffff'h } ::= { ifTableXtndEntry 39 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.1.1.40 ifTableXtndFrTrafficShaping OBJECT-TYPE SYNTAX OnOff MAX-ACCESS read-write STATUS current DESCRIPTION "This object determines / indicates whether Frame-Relay Traffic-Shaping is enabled (on) or disabled (off) for this interface. This object can be set only for interfaces, but not for sub-interfaces. This object is applicable only for interfaces which ifTableXtndEncapsulation is Frame-Relay (i.e. frameRelay, frameRelayNonIetf)." DEFVAL { off } ::= { ifTableXtndEntry 40 } ifTableXtndType OBJECT-TYPE SYNTAX INTEGER { nullModem(1), usrSporsterModem(2), multitechZbaModem(3), multitechIsdnModem(4), notSupported(255) } MAX-ACCESS read-write STATUS current DESCRIPTION " Extended type is, currently, required for modem interfaces " ::= { ifTableXtndEntry 41 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.2 -- 1.3.6.1.4.1.6889.2.1.6.2.2.2 xtndKeepAliveTable OBJECT-TYPE SYNTAX SEQUENCE OF XtndKeepAliveEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Extended Keepalive Parameters Table." ::= { ifTablePrivateExtensions 2 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1 -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1 xtndKeepAliveEntry OBJECT-TYPE SYNTAX XtndKeepAliveEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the extended keepalive parameters. The Table is per interface. Although for the first phase it will be relevant for WAN Fast Ethernet Port. But may be available in the future for interface. The keepalive on specific interface may bring it to line protocol down according the results. The main idea is to check certain IP that if not responding then the link/route may be down and therefore the interface is bring to line protocol down. In this case there still be sent extended keepalive packets in order to check whether the line protocol is up. " INDEX { xtndKeepAliveifIndex } ::= { xtndKeepAliveTable 1 } XtndKeepAliveEntry ::= SEQUENCE { xtndKeepAliveifIndex InterfaceIndex, xtndKeepAliveMethod INTEGER, xtndKeepAliveTimeout Integer32, xtndKeepAliveUpRetries Integer32, xtndKeepAliveDownRetries Integer32, xtndKeepAliveInterval Integer32, xtndKeepAliveSrcIPAddr IpAddress, xtndKeepAliveIPAddr IpAddress, xtndKeepAliveNextHopMAC PhysAddress, xtndKeepAliveStatus INTEGER, xtndKeepAliveMode INTEGER } -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.1 -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.1 xtndKeepAliveifIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index in the ifTable for which this row is providing information." ::= { xtndKeepAliveEntry 1 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.2 -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.2 xtndKeepAliveMethod OBJECT-TYPE SYNTAX INTEGER { icmpPing(1), tcpConnect(2), httpGet(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of the extended keepalive. icmpPing(1),tcpConnect(2),httpGet(3) Default is IcmpPing." DEFVAL { icmpPing } ::= { xtndKeepAliveEntry 2 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.3 -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.3 xtndKeepAliveTimeout OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Timeout in seconds to wait for a reply. Applicable to non-TCP tests such as ICMP Echo, UDP. Default 1second." ::= { xtndKeepAliveEntry 3 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.4 -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.4 xtndKeepAliveUpRetries OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The number of successful extended keepalive necessary to determine that the next hop router is operational." ::= { xtndKeepAliveEntry 4 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.5 -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.5 xtndKeepAliveDownRetries OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The number of unsuccessful extedned keepalive necessary to determine that the next hop router is not operational." ::= { xtndKeepAliveEntry 5 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.6 -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.6 xtndKeepAliveInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The extended keepliave interval in seconds" ::= { xtndKeepAliveEntry 6 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.7 -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.7 xtndKeepAliveSrcIPAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The Source IP address to use. Default is the primary IP address of the interface. Setting the address 0.0.0.0 will reset the xtndKeepAliveSrcIPAddr to the primary IP interface address" DEFVAL { '7f000001'h } ::= { xtndKeepAliveEntry 7 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.8 -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.8 xtndKeepAliveIPAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address that it status shall be checked. " DEFVAL { '00000000'h } ::= { xtndKeepAliveEntry 8 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.9 -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.9 xtndKeepAliveNextHopMAC OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The next Hop MAC, Valid for Ethernet Interfaces." DEFVAL { '000000000000'h } ::= { xtndKeepAliveEntry 9 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.10 xtndKeepAliveStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), disable(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Status of the extended KeepAlive. I.e. whether the current extended KeepAlive succeeded. 1 - up 2 - down 3 - disable " ::= { xtndKeepAliveEntry 10 } -- 1.3.6.1.4.1.6889.2.1.6.2.2.2.1.11 xtndKeepAliveMode OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Extended KeepAlive Mode. 1 - enable 2 - disable" ::= { xtndKeepAliveEntry 11 } -- Frame Relay Specific Interface extensions. -- The extemsions extend the MIB defined in RFC2115. -- 1.3.6.1.4.1.6889.2.1.6.2.4 -- 1.3.6.1.4.1.6889.2.1.6.2.4 frameRelay OBJECT IDENTIFIER ::= { ifs 4 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.1 -- 1.3.6.1.4.1.6889.2.1.6.2.4.1 frDlcmiXtndTable OBJECT-TYPE SYNTAX SEQUENCE OF FrDlcmiXtndEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table extends the standard frDlcmiTable, which models RFR I/Fs. Entries are created by the agent for Frame Relay I/Fs, and are deleted when those entries are deleted." REFERENCE "RFC2115:frDlcmiTable" ::= { frameRelay 1 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.1.1 -- 1.3.6.1.4.1.6889.2.1.6.2.4.1.1 frDlcmiXtndEntry OBJECT-TYPE SYNTAX FrDlcmiXtndEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each Entry corresponds to a Frame Relay Interface. Entries are created & deleted automatically by the agent, when ifTableXtndEncapsulation of the underlying Layer 1 Interface is changed. " INDEX { frDlcmiXtndIndex } ::= { frDlcmiXtndTable 1 } FrDlcmiXtndEntry ::= SEQUENCE { frDlcmiXtndIndex InterfaceIndex, frDlcmiXtndLMIAutoSense OnOff } -- 1.3.6.1.4.1.6889.2.1.6.2.4.1.1.1 -- 1.3.6.1.4.1.6889.2.1.6.2.4.1.1.1 frDlcmiXtndIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The ifIndex assigned to The Frame Relay interface is calculated by a known formula, which is agent-type specific." ::= { frDlcmiXtndEntry 1 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.1.1.2 -- 1.3.6.1.4.1.6889.2.1.6.2.4.1.1.2 frDlcmiXtndLMIAutoSense OBJECT-TYPE SYNTAX OnOff MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable automatic detection (By sending all supported keepalives) of the Local Management Interface (LMI) on the Frame Relay Interface." DEFVAL { on } ::= { frDlcmiXtndEntry 2 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.2 -- 1.3.6.1.4.1.6889.2.1.6.2.4.2 frStaticCircuitTable OBJECT-TYPE SYNTAX SEQUENCE OF FrStaticCircuitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to create/associate/delete A Virtual Channel (DLCI) with a specific Frame Relay Sub Interface. When an entry is created in this table: If the DLCI is the same as that of a dynamic frCircuit leraned on the Frame Relay Interface layered bellow the Sub Interface specified by the entry then: - The DLCI's status is changed to Static Else - A new static DLCI is created. In both cases, the static DLCI is assigned to the specified Frame Relay Sub Interface. " ::= { frameRelay 2 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.2.1 -- 1.3.6.1.4.1.6889.2.1.6.2.4.2.1 frStaticCircuitEntry OBJECT-TYPE SYNTAX FrStaticCircuitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An Entry represent a Virtual Channel available on a specific Frame Relay Interface. " INDEX { frStaticCircuitSubIfIndex, frStaticCircuitDLCI, frStaticCircuitDLCIrole } ::= { frStaticCircuitTable 1 } FrStaticCircuitEntry ::= SEQUENCE { frStaticCircuitSubIfIndex InterfaceIndex, frStaticCircuitDLCI DLCI, frStaticCircuitDLCIrole INTEGER, frStaticCircuitStatus RowStatus, frStaticCircuitMapClass DisplayString } -- IfIndex of the Frame Relay Sub Interface -- this VC is associated with. -- 1.3.6.1.4.1.6889.2.1.6.2.4.2.1.1 -- 1.3.6.1.4.1.6889.2.1.6.2.4.2.1.1 frStaticCircuitSubIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Description." ::= { frStaticCircuitEntry 1 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.2.1.2 -- 1.3.6.1.4.1.6889.2.1.6.2.4.2.1.2 frStaticCircuitDLCI OBJECT-TYPE SYNTAX DLCI MAX-ACCESS read-only STATUS current DESCRIPTION "The virtual channel identifier. " ::= { frStaticCircuitEntry 2 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.2.1.3 -- 1.3.6.1.4.1.6889.2.1.6.2.4.2.1.3 frStaticCircuitDLCIrole OBJECT-TYPE SYNTAX INTEGER { priority6to7(1), priority4to5(2), priority2to3(3), priority0to1(4), primary(100) } MAX-ACCESS read-only STATUS current DESCRIPTION "The role of the VC in this interface. primary - the state of this VC determines the operStatus of the interface. For point to point interfaces, the agent will not permit more than one primary to exist. A sub interface for which no primary is defined will be down. priority6to7 - This VC handles high priority (forwarding class 6 to 7)traffic. If this VC does not exists, the sub interface will send all traffic through the primary VC (no priority-dlci-group) In point to point interfaces, only one such VC can be configured. priority4to5 - This VC handles Medium priority (forwarding class 4 to 5)traffic. If this VC does not exists, the sub interface will send all traffic through the primary VC (no priority-dlci-group) In point to point interfaces, only one such VC can be configured. priority2to3 - This VC handles Normal priority (forwarding class 2 to 3)traffic. If this VC does not exists, the sub interface will send all traffic through the primary VC (no priority-dlci-group) In point to point interfaces, only one such VC can be configured. priority0to1 - This VC handles Low priority (forwarding class 0 to 1)traffic. If this VC does not exists, the sub interface will send all traffic through the primary VC (no priority-dlci-group) In point to point interfaces, only one such VC can be configured. " ::= { frStaticCircuitEntry 3 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.2.1.4 -- 1.3.6.1.4.1.6889.2.1.6.2.4.2.1.4 frStaticCircuitStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Used to create/associate/delete a DLCI to a Sub FrameRelay Interface. Note that the frStaticCircuitDLCIrole defines limitations on creation and deletion of DLCIs. The notInService state will not be implemented." ::= { frStaticCircuitEntry 4 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.2.1.5 frStaticCircuitMapClass OBJECT-TYPE SYNTAX DisplayString (SIZE (1..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "A pointer to a 'map-class frame-relay' entry applicable for this row. A 'map-class frame-relay' is an entry in the frMapClassTable. The value of this object must be identical to the value of the desired entry's frMapClassName in the frMapClassTable. NOTES: 1. This object can only a point to an existing entry. Trying to set this object to a value that does not pertain to an existing entry in frMapClassTable shall fail. 2. An entry in the frMapClassTable can be deleted only when it is not pointed to by any entry in this table (frStaticCircuitTable). 3. The map-class is activated only when the containing interface has Frame-Relay Traffic-Shaping enables. See description of ifTableXtndFrTrafficShaping for details about FRTS. 4. The frMapClassTable contains a persistent, non-deletable default entry, by the name 'default'." DEFVAL { "default" } ::= { frStaticCircuitEntry 5 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.3 -- 1.3.6.1.4.1.6889.2.1.6.2.4.3 frSubIfTable OBJECT-TYPE SYNTAX SEQUENCE OF FrSubIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Frame Relay Sub Interface is the Layer 2 interface to which Layer 3 (IP) Interfaces are assigned. This Logical Interface is hinted at but not modeled by the RFC2115 Frame-Relay DTE MIB. This table manages the creation/deletion of Frame Relay Sub I/Fs. Entries are created by the Creator of a sub-I/F." ::= { frameRelay 3 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.3.1 -- 1.3.6.1.4.1.6889.2.1.6.2.4.3.1 frSubIfEntry OBJECT-TYPE SYNTAX FrSubIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An Entry in this table defines a Frame Relay Sub Interface of a specific type, defined over a specific Frame Relay Interface. Note that although the MIB model allow for two SubFR I/Fs to have the same ifIndex and have different Frame Relay I/Fs or FR types, the agent will allow only a single suc interface - the first one defined. " INDEX { frSubIfDlcmiIndex, frSubIfSubIndex, frSubIfType } ::= { frSubIfTable 1 } FrSubIfEntry ::= SEQUENCE { frSubIfDlcmiIndex InterfaceIndex, frSubIfSubIndex InterfaceIndex, frSubIfType INTEGER, frSubIfStatus RowStatus } -- 1.3.6.1.4.1.6889.2.1.6.2.4.3.1.1 -- 1.3.6.1.4.1.6889.2.1.6.2.4.3.1.1 frSubIfDlcmiIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The ifIndex of the Frame Relay Interface this Sub Interface is created over." ::= { frSubIfEntry 1 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.3.1.2 -- 1.3.6.1.4.1.6889.2.1.6.2.4.3.1.2 frSubIfSubIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The ifIndex of the Sub Interface. Note that the Mnagement station must select a sub interface number in the permissible range (which is agent-type dependent.) Agent Type ifIndex Range ========== ============= X330WAN 8000-8999 " ::= { frSubIfEntry 2 } -- The X330WAN V1.5 will support ONLY the point2point type -- 1.3.6.1.4.1.6889.2.1.6.2.4.3.1.3 -- 1.3.6.1.4.1.6889.2.1.6.2.4.3.1.3 frSubIfType OBJECT-TYPE SYNTAX INTEGER { point2point(1), point2multiPoint(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Type of the Sub Interface. point2point - A Point to Point Interface. Point2multiPoint - Point to multi-point interface." ::= { frSubIfEntry 3 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.3.1.4 -- 1.3.6.1.4.1.6889.2.1.6.2.4.3.1.4 frSubIfStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Creation/Deletion of a Frame Relay Sub Interface over a Frame Relay Interface. The Agent will refuse to delete a Sub Interface if there are IP Interfaces associated with it. " ::= { frSubIfEntry 4 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.4 frMapClassTable OBJECT-TYPE SYNTAX SEQUENCE OF FrMapClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the 'map-class frame-relay' entries in the system. A 'map-class frame-relay' entry is a collection of QoS-related parameters that can be attached to a Frame-Relay DLCI. An entry in this table can be attached to a DLCI by setting the value of frStaticCircuitMapClass in frStaticCircuitTable to the value of the frMapClassName of an entry in this table. An entry in this table can be deleted only when it is not pointed to by any entry in frStaticCircuitTable. Trying to delete an entry that does not correspond to that shall fail. This table contains a default entry that can be modified, but cannot be deleted. The value of frMapClassName for that entry is 'default'." ::= { frameRelay 4 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.4.1 frMapClassEntry OBJECT-TYPE SYNTAX FrMapClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, which represents a 'frame-relay map-class' object." INDEX { IMPLIED frMapClassName } ::= { frMapClassTable 1 } FrMapClassEntry ::= SEQUENCE { frMapClassName DisplayString, frMapClassBcOut Unsigned32, frMapClassBeOut Unsigned32, frMapClassCirOut Unsigned32, frMapClassFrf12Frag Integer32, frMapClassRowStatus RowStatus } -- 1.3.6.1.4.1.6889.2.1.6.2.4.4.1.1 frMapClassName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..64)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of the map-class, which is also the only index component of this table. NOTE: This object can only contain a lower-case string! Trying to use upper-case characters on creation shall result in a failure." ::= { frMapClassEntry 1 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.4.1.2 frMapClassBcOut OBJECT-TYPE SYNTAX Unsigned32 UNITS "Bits" MAX-ACCESS read-write STATUS current DESCRIPTION "The output Commited Burst size, in bits. Valid range is 300-39999999." DEFVAL { 7000 } ::= { frMapClassEntry 2 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.4.1.3 frMapClassBeOut OBJECT-TYPE SYNTAX Unsigned32 UNITS "Bits" MAX-ACCESS read-write STATUS current DESCRIPTION "The output Excess Burst size, in bits. Valid range is 0-39999999." DEFVAL { 0 } ::= { frMapClassEntry 3 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.4.1.4 frMapClassCirOut OBJECT-TYPE SYNTAX Unsigned32 UNITS "Bits per second" MAX-ACCESS read-write STATUS current DESCRIPTION "The Committed Information Rate, in bits per second. Valid range is 1000-39999999." DEFVAL { 56000 } ::= { frMapClassEntry 4 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.4.1.5 frMapClassFrf12Frag OBJECT-TYPE SYNTAX Integer32 (0 | 16..1600) UNITS "Bytes" MAX-ACCESS read-write STATUS current DESCRIPTION "Disable or enable FRF.12 fragmentation, and determine fragment size: The reserved value zero means FRF.12 fragmentation is disabled. A value larger then zero means FRF.12 fragmentation is enabled, and the fragment size in bytes is equal to the value of this object. " DEFVAL { 0 } ::= { frMapClassEntry 5 } -- 1.3.6.1.4.1.6889.2.1.6.2.4.4.1.6 frMapClassRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to create a new row or destroy an existing row in the manner described in the definition of the RowStatus textual convention. The value of this object has no effect on whether other objects in this conceptual row can be modified. Use createAndGo (not createAndWait) to create this row." ::= { frMapClassEntry 6 } -- 1.3.6.1.4.1.6889.2.1.6.6 -- 1.3.6.1.4.1.6889.2.1.6.2.5 wanDialer OBJECT IDENTIFIER ::= { ifs 5 } -- -------------------------------------------------------------------------------------------- -- 1.3.6.1.4.1.6889.2.1.6.6.1 -- 1.3.6.1.4.1.6889.2.1.6.2.5.1 wanDialerTable OBJECT-TYPE SYNTAX SEQUENCE OF WanDialerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used for configuring Dialer interfaces. " ::= { wanDialer 1 } -- 1.3.6.1.4.1.6889.2.1.6.6.1.1 -- 1.3.6.1.4.1.6889.2.1.6.2.5.1.1 wanDialerEntry OBJECT-TYPE SYNTAX WanDialerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " " INDEX { ifIndex } ::= { wanDialerTable 1 } WanDialerEntry ::= SEQUENCE { wanDialerModemIf Integer32, wanDialerState INTEGER, wanDialerPersistentDelay Integer32, wanDialerPersistentMaxAttempts Integer32, wanDialerPersistentReenable Integer32, wanDialerOrder INTEGER, wanDialerString1 DisplayString, wanDialerString2 DisplayString, wanDialerString3 DisplayString, wanDialerString4 DisplayString, wanDialerString5 DisplayString, wanDialerLastDialed DisplayString, wanDialerWaitForIpcp Integer32, wanDialerPersistentInitial Integer32 } -- 1.3.6.1.4.1.6889.2.1.6.6.1.1.1 -- 1.3.6.1.4.1.6889.2.1.6.2.5.1.1.1 wanDialerModemIf OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The ifIndex of the modem interface" ::= { wanDialerEntry 1 } -- 1.3.6.1.4.1.6889.2.1.6.6.1.1.2 -- 1.3.6.1.4.1.6889.2.1.6.2.5.1.1.2 wanDialerState OBJECT-TYPE SYNTAX INTEGER { initModem(1), idle(2), waiting4Modem(3), maxAttemptsDisabled(4), preDialReset(5), waitForConnect(6), waitForDCD(7), hangUp(8), persistentDelay(9), waitForIPCP(10), connected(11) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current state of the dialer finit-state-machine" ::= { wanDialerEntry 2 } -- 1.3.6.1.4.1.6889.2.1.6.6.1.1.3 -- 1.3.6.1.4.1.6889.2.1.6.2.5.1.1.3 wanDialerPersistentDelay OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The number of seconds between persistent dial attempts (zero= no persistent dialing)" ::= { wanDialerEntry 3 } -- 1.3.6.1.4.1.6889.2.1.6.6.1.1.4 -- 1.3.6.1.4.1.6889.2.1.6.2.5.1.1.4 wanDialerPersistentMaxAttempts OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The interval between persistent (non-DDR) dial attempts. Zero means no persistent dialing" ::= { wanDialerEntry 4 } -- 1.3.6.1.4.1.6889.2.1.6.6.1.1.5 -- 1.3.6.1.4.1.6889.2.1.6.2.5.1.1.5 wanDialerPersistentReenable OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The time (in seconds) the dialer is disabled after it exhausts its consecutive dial attempts quota (wanDialerPersistentMaxAttempts). Zero means that the dialer is disabled until the dialing the current dial trigger disappears." ::= { wanDialerEntry 5 } -- 1.3.6.1.4.1.6889.2.1.6.6.1.1.6 -- 1.3.6.1.4.1.6889.2.1.6.2.5.1.1.6 wanDialerOrder OBJECT-TYPE SYNTAX INTEGER { sequential(1), roundRobin(2), lastSuccessful(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The dial strings list usage order where: sequential(1) : The dialer starts from the beginning of the list when there is a new reason to dial (dial trigger. roundRobin(2): The dialer use the dialing string that is right after the last one dialed. lastSuccessful(3) : If the previous dial attempt was successful, the dialer starts with its dial strings." ::= { wanDialerEntry 6 } -- 1.3.6.1.4.1.6889.2.1.6.6.1.1.7 -- 1.3.6.1.4.1.6889.2.1.6.2.5.1.1.7 wanDialerString1 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The 1st dial string in the list(NULL=unconfigured)" ::= { wanDialerEntry 7 } -- 1.3.6.1.4.1.6889.2.1.6.6.1.1.8 -- 1.3.6.1.4.1.6889.2.1.6.2.5.1.1.8 wanDialerString2 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The 2nd dial string in the list(NULL=unconfigured)" ::= { wanDialerEntry 8 } -- 1.3.6.1.4.1.6889.2.1.6.6.1.1.9 -- 1.3.6.1.4.1.6889.2.1.6.2.5.1.1.9 wanDialerString3 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The 3rd dial string in the list(NULL=unconfigured)" ::= { wanDialerEntry 9 } -- 1.3.6.1.4.1.6889.2.1.6.6.1.1.10 -- 1.3.6.1.4.1.6889.2.1.6.2.5.1.1.10 wanDialerString4 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The 4th dial string in the list(NULL=unconfigured)" ::= { wanDialerEntry 10 } -- 1.3.6.1.4.1.6889.2.1.6.6.1.1.11 -- 1.3.6.1.4.1.6889.2.1.6.2.5.1.1.11 wanDialerString5 OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The 5th dial string in the list(NULL=unconfigured)" ::= { wanDialerEntry 11 } -- 1.3.6.1.4.1.6889.2.1.6.6.1.1.12 -- 1.3.6.1.4.1.6889.2.1.6.2.5.1.1.12 wanDialerLastDialed OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The last used display string" ::= { wanDialerEntry 12 } -- 1.3.6.1.4.1.6889.2.1.6.6.1.1.13 -- 1.3.6.1.4.1.6889.2.1.6.2.5.1.1.13 wanDialerWaitForIpcp OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum time (in seconds) the dialer waits from dialing until PPP/IPCP is up. " DEFVAL { 45 } ::= { wanDialerEntry 13 } -- 1.3.6.1.4.1.6889.2.1.6.6.1.1.14 -- 1.3.6.1.4.1.6889.2.1.6.2.5.1.1.14 wanDialerPersistentInitial OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The minimum delay (in seconds) from boot to persitent dialing." DEFVAL { 10 } ::= { wanDialerEntry 14 } -- 1.3.6.1.4.1.6889.2.1.6.4 -- 1.3.6.1.4.1.6889.2.1.6.4 avayaEISWanTraps OBJECT IDENTIFIER ::= { avayaEISWan 4 } -- 1.3.6.1.4.1.6889.2.1.6.5 -- 1.3.6.1.4.1.6889.2.1.6.5 avayaEISWanGroups OBJECT IDENTIFIER ::= { avayaEISWan 5 } -- 1.3.6.1.4.1.6889.2.1.6.5.1 -- 1.3.6.1.4.1.6889.2.1.6.5.1 hostModuleGroup OBJECT-GROUP OBJECTS { intWanGroupID, intWanPortID, intWanPortSpeed, intWanPortMode, intWanPortAutoNegotiation, intWanPortVLANMode, intWanPortVLANBindingMode, intWanPortVlanList } STATUS current DESCRIPTION "Mib objects for controlling the fabric port, connecting a LAN switch to its WAN router." ::= { avayaEISWanGroups 1 } -- 1.3.6.1.4.1.6889.2.1.6.5.2 -- 1.3.6.1.4.1.6889.2.1.6.5.2 wanRouterBladeGroup OBJECT-GROUP OBJECTS { ds0BundleSpeedFactor, ifTableXtndIndex, ifTableXtndPeerAddress, ifTableXtndVoIPQueue, ifTableXtndCableLength, ifTableXtndGain, ifTableXtndDescription, ifTableXtndKeepAlive, ifTableXtndMtu, ifTableXtndInvertTxClock, ifTableXtndDTELoopback, ifTableXtndIgnoreDCD, ifTableXtndIdleChars, ifTableXtndBandwidth, ifTableXtndEncapsulation, frDlcmiXtndLMIAutoSense, frDlcmiXtndIndex, frSubIfDlcmiIndex, frSubIfSubIndex, frSubIfType, frSubIfStatus, frStaticCircuitDLCIrole, ifTableXtndPrimaryIf, ifTableXtndBackupDisableDelay, ifTableXtndBackupEnableDelay, ifTableXtndBackupIf, ifTableXtndBackupCapabilities, ds1DeviceMode, ds0BundleMemmbersList, ifTableXtndOperStatus, frStaticCircuitSubIfIndex, frStaticCircuitDLCI, frStaticCircuitStatus, ifTableXtndReliability, ifTableXtndOutputLoad, ifTableXtndInputLoad, ifTableXtndOutputRate, ifTableXtndInputRate, ifTableXtndLoadInterval, ifTableXtndDtrPulseTime, frMapClassRowStatus, frMapClassFrf12Frag, frMapClassCirOut, frMapClassBeOut, frMapClassBcOut, ifTableXtndFrTrafficShaping, frStaticCircuitMapClass, ifTableXtndDtrRestartDelay, ifTableXtndCarrierDelay } STATUS current DESCRIPTION "Mib object that belong to the WAN router." ::= { avayaEISWanGroups 2 } -- -------------------------------------------------------------------------------------------- -- 1.3.6.1.4.1.6889.2.1.6.7 -- 1.3.6.1.4.1.6889.2.1.6.7 avayaEISWanCompliances OBJECT IDENTIFIER ::= { avayaEISWan 7 } -- 1.3.6.1.4.1.6889.2.1.6.7.1 -- this module -- 1.3.6.1.4.1.6889.2.1.6.7.1 hostModuleCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The host module should only support the host module group." MODULE -- this module MANDATORY-GROUPS { hostModuleGroup } ::= { avayaEISWanCompliances 1 } -- 1.3.6.1.4.1.6889.2.1.6.7.2 -- this module -- 1.3.6.1.4.1.6889.2.1.6.7.2 wanRouterBladeCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The wan router blade should support the wan router blade group." MODULE -- this module MANDATORY-GROUPS { wanRouterBladeGroup } ::= { avayaEISWanCompliances 2 } END -- -- WAN-MIB.my --