-- Copyright (C) 2014 Aricent Group . All Rights Reserved -- $Id: fsy1564.mib,v 1.5 2016/01/29 13:08:15 siva Exp $ -- ARICENT Y1564 proprietary MIB Definition ARICENT-Y1564-CFG-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE, NOTIFICATION-TYPE, enterprises, Unsigned32, Integer32 FROM SNMPv2-SMI DisplayString, TruthValue, TimeStamp, RowStatus FROM SNMPv2-TC MODULE-IDENTITY FROM SNMPv2-SMI IEEE8021PriorityCodePoint FROM IEEE8021-TC-MIB VlanId FROM Q-BRIDGE-MIB; fsY1564 MODULE-IDENTITY LAST-UPDATED "201406180000Z" ORGANIZATION "ARICENT COMMUNICATIONS SOFTWARE" CONTACT-INFO "The Aricent Group, One Tower Center Boulevard, 18th Floor, East Brunswick, NJ 08816, USA E-mail:support@aricent.com" DESCRIPTION "The enterprise ID 29601 is originally assigned to Aricent Communications Pvt. Limited. Aricent Communications is a part of Aricent Group." REVISION "201406180000Z" DESCRIPTION "The proprietary MIB for Aricent Y1564 Configurations." ::= { enterprises aricent-communication-holding-ltd(29601) iss(2) 88 } -- ***************************************************************************** -- Groups in Y1564 MIB -- ***************************************************************************** fsY1564Context OBJECT IDENTIFIER ::= { fsY1564 1 } fsY1564Sla OBJECT IDENTIFIER ::= { fsY1564 2 } fsY1564TrafProf OBJECT IDENTIFIER ::= { fsY1564 3 } fsY1564Sac OBJECT IDENTIFIER ::= { fsY1564 4 } fsY1564ServiceConf OBJECT IDENTIFIER ::= { fsY1564 5 } fsY1564ConfigTest OBJECT IDENTIFIER ::= { fsY1564 6 } fsY1564PerformanceTest OBJECT IDENTIFIER ::= { fsY1564 7 } fsY1564PerfTestReport OBJECT IDENTIFIER ::= { fsY1564 8 } fsY1564Notification OBJECT IDENTIFIER ::= { fsY1564 9 } --- *********************************************************************** -- Context Table --- *********************************************************************** fsY1564ContextTable OBJECT-TYPE SYNTAX SEQUENCE OF FsY1564ContextEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of Y1564 module parameters per Y1564 Virtual Context." ::= { fsY1564Context 1 } fsY1564ContextEntry OBJECT-TYPE SYNTAX FsY1564ContextEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains virtual context specific Y1564 module parameters." INDEX { fsY1564ContextId } ::= { fsY1564ContextTable 1 } FsY1564ContextEntry ::= SEQUENCE { fsY1564ContextId Unsigned32, fsY1564ContextName DisplayString, fsY1564ContextSystemControl INTEGER, fsY1564ContextModuleStatus INTEGER, fsY1564ContextTraceOption Unsigned32, fsY1564ContextTrapStatus INTEGER, fsY1564ContextNumOfConfTestRunning Unsigned32, fsY1564ContextNumOfPerfTestRunning Unsigned32 } fsY1564ContextId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Identifies the virtual context in the system " ::= { fsY1564ContextEntry 1 } fsY1564ContextName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the context-name for this virtual context." ::= { fsY1564ContextEntry 2 } fsY1564ContextSystemControl OBJECT-TYPE SYNTAX INTEGER { start(1), shutdown(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative system control status of Y1564 module. The value 'start' (1) indicates that all resources required by Y1564 should be allocated and Y1564 should be supported in the virtual context. The value 'shutdown(2)' indicates that Y1564 module should be shutdown in the virtual context and all allocated memory should be released. By default this object is set to 'shutdown (2)' for all virtual contexts." DEFVAL { shutdown } ::= { fsY1564ContextEntry 3 } fsY1564ContextModuleStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative module status of Y1564 module. The value 'enable (1)' indicates that Y1564 should be enabled in the virtual context The value 'disable (2)' indicates that Y1564 should be disabled in the virtual context. In the disabled state, all the running tests will be stopped, though configuration can still be done. By default this object is set to disable(2) for all virtual contexts." DEFVAL { disable } ::= { fsY1564ContextEntry 4 } fsY1564ContextTraceOption OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to enable the trace statements in Y1564 Module. A FOUR BYTE integer is specified for enabling the level of tracing. Each BIT in the four byte integer, represents a level of Trace. The mapping between the bit positions & the level of trace is as follows: 0 - Init and Shutdown Traces 1 - Management Traces 2 - Control Plane Traces 3 - Traces related to All Resources except Buffers 4 - Timer start, stop and expiry related Traces 5 - Critical Traces 6 - Y1731 interface related Traces 7 - Configuration/Performance test traces 8 - Session record traces The remaining bits are unused. Combination of levels are also allowed. For example if the bits 0 and 1 are set, then the Trace statements related to Init-Shutdown and Management are generated. The user has to enter the corresponding INTEGER VALUE for the bits set. For example if bits 0 and 1 are to be set, the user has to enter the value 3. By default, critical trace(bit 5) is set." DEFVAL { '00000020'H } ::= { fsY1564ContextEntry 5 } fsY1564ContextTrapStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable (2)} MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to enable or disable the transmission of TRAP notification messages. By default this object is set to enable(1) for all virtual contexts." DEFVAL { enable } ::= { fsY1564ContextEntry 6 } fsY1564ContextNumOfConfTestRunning OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of configuration tests are currently running in the virtual context." ::= { fsY1564ContextEntry 7 } fsY1564ContextNumOfPerfTestRunning OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of performance test are currently running in the virtual context." ::= { fsY1564ContextEntry 8 } --- *********************************************************************** -- Service Level Agreement Table --- *********************************************************************** fsY1564SlaTable OBJECT-TYPE SYNTAX SEQUENCE OF FsY1564SlaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Y1564 Service Level Agreement configurations. SLA is an Agreement between service provider and subscribers" ::= { fsY1564Sla 1 } fsY1564SlaEntry OBJECT-TYPE SYNTAX FsY1564SlaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains information about a particular Y1564 SLA Configuration." INDEX { fsY1564ContextId, fsY1564SlaId } ::= { fsY1564SlaTable 1 } FsY1564SlaEntry ::= SEQUENCE { fsY1564SlaId Unsigned32, fsY1564SlaEvcIndex VlanId, fsY1564SlaMEG Unsigned32, fsY1564SlaME Unsigned32, fsY1564SlaMEP Unsigned32, fsY1564SlaSacId Unsigned32, fsY1564SlaTrafProfileId Unsigned32, fsY1564SlaStepLoadRate Integer32, fsY1564SlaConfTestDuration Integer32, fsY1564SlaTestStatus INTEGER, fsY1564SlaServiceConfId Unsigned32, fsY1564SlaColorMode INTEGER, fsY1564SlaCoupFlag TruthValue, fsY1564SlaCIR Unsigned32, fsY1564SlaCBS Unsigned32, fsY1564SlaEIR Unsigned32, fsY1564SlaEBS Unsigned32, fsY1564SlaTrafPolicing INTEGER, fsY1564SlaTestSelector Integer32, fsY1564SlaCurrentTestMode Integer32, fsY1564SlaCurrentTestState INTEGER, fsY1564SlaRowStatus RowStatus } fsY1564SlaId OBJECT-TYPE SYNTAX Unsigned32 ( 1..10 ) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the Y1564 Service Level Agreement Identifier (An Agreement between service provider and subscribers). This is a free running index used to identify the SLA. " ::= { fsY1564SlaEntry 1 } fsY1564SlaEvcIndex OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the service provider VLAN (S-VLAN) on which service is created. The EVC is configured using MEF MIB. Internally this object refers to fsEvcIndex in MEF MIB." ::= { fsY1564SlaEntry 2 } fsY1564SlaMEG OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Maintenance Entity Group (MEG) of the fsY1564SlaEntry. Internally this object refers to MIB object dot1agCfmMdIndex of ECFM 802.1ag standard. The value Zero is used for unmapping MEG from Sla." ::= { fsY1564SlaEntry 3 } fsY1564SlaME OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Maintenance Entity (ME) of the fsY1564SlaEntry.Internally this object refers to MIB object dot1agCfmMaIndex of ECFM 802.1ag standard. The value Zero is used for unmapping ME from Sla" ::= { fsY1564SlaEntry 4 } fsY1564SlaMEP OBJECT-TYPE SYNTAX Unsigned32 (0..8191) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Maintenance Association End Point (MEP) of the fsY1564SlaEntry. Internally this object refers to MIB object dot1agCfmMepIdentifier of ECFM 802.1ag standard. The value Zero is used for unmapping MEP from Sla" ::= { fsY1564SlaEntry 5 } fsY1564SlaSacId OBJECT-TYPE SYNTAX Unsigned32 (0..10) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Service Acceptance Criteria to which the SLA is currently mapped.Multiple SACs can be created and each can be associated to a given SLA.Each SAC refers to the minimum Information rate, frame loss ratio, frame transmit delay, frame delay variation and availability for the service under test. The value Zero is used for unmapping Sac from Sla" ::= { fsY1564SlaEntry 6 } fsY1564SlaTrafProfileId OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Traffic Profile to which the SLA is currently mapped. Multiple packet profiles can be created and each can be associated to a given SLA. Each packet profile contains packet information such as Packet Size, Payload , and EMIX pattern. The value Zero is used for unmapping Traffic Profile from Sla" ::= { fsY1564SlaEntry 7 } fsY1564SlaStepLoadRate OBJECT-TYPE SYNTAX Integer32 ( 10..100 ) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the step load rate of the step load CIR (Committed Information Rate) configuration test. If no value is provided, 25% of CIR is sent first,followed by 50% of CIR and so on; the complete CIR is generated in 4 steps. For eg, If step load rate is configured as 10, CIR test will be done with traffic rate incremented as 10% for each and every step." DEFVAL { 25 } ::= { fsY1564SlaEntry 8 } fsY1564SlaConfTestDuration OBJECT-TYPE SYNTAX Integer32 ( 10..60 ) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the duration of each individual test in seconds. If Configuration test is started with CIR, EIR, Traffic Policing and fsY1564SlaConfTestDurationis specified as 10 then all the three tests should be completed within 30 seconds." DEFVAL { 30 } ::= { fsY1564SlaEntry 9 } fsY1564SlaTestStatus OBJECT-TYPE SYNTAX INTEGER { start(1), stop(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Y1564 Service Configuration test initiation status. An enumerated value set to 'start' initiates service configuration test based on bits selected in object fsY1564SlaTestSelector. If Bits 0 and 1 are set in object fsY1564SlaTestSelector and fsY1564SlaTestStatus is set as start then Service configuration test will be started. An enumerated value set to 'stop' stops service configuration test. In Y1564, either Service Configuration Test or Service Performance Test can be initiated for the same SLA but both cannot be allowed at the same time." DEFVAL { 2 } ::= { fsY1564SlaEntry 10 } fsY1564SlaServiceConfId OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Service Configuration to which the SLA is currently mapped. Multiple services can be created and each can be associated to a given SLA. Each service contains the service configuration information such as CIR, CEB, EIR, EBS, ColorMode and CoupFlag. This configuration is allowed only when MEF module is not defined." ::= { fsY1564SlaEntry 11 } fsY1564SlaColorMode OBJECT-TYPE SYNTAX INTEGER { colorAware(1), colorBlind(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies whether the color-aware or color blind property is employed by the bandwidth profile. The default value for this object is ColorBlind." DEFVAL { 2 } ::= { fsY1564SlaEntry 12 } fsY1564SlaCoupFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the modes of operation of the rate enforcement algorithm. The choice of the value for CF has the effect of controlling the volume of the Service Frames that are declared Yellow. When CF is set to 0, the long term average bit rate of Service Frames that are declared Yellow is bounded by EIR. When CF is set to 1, the long term average bit rate of Service Frames that are declared Yellow is bounded by CIR + EIR depending on volume of the offered Service Frames that are declared Green " ::= { fsY1564SlaEntry 13 } fsY1564SlaCIR OBJECT-TYPE SYNTAX Unsigned32 (0..10485760) MAX-ACCESS read-only STATUS current DESCRIPTION "The committed information rate Must be >= 0. CIR must be less than or equal to EIR,if EIR > 0." ::= { fsY1564SlaEntry 14 } fsY1564SlaCBS OBJECT-TYPE SYNTAX Unsigned32 (0..10485760) UNITS "Bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The committed burst size Must be > 0 if CIR > 0." ::= { fsY1564SlaEntry 15 } fsY1564SlaEIR OBJECT-TYPE SYNTAX Unsigned32 (0..10485760) MAX-ACCESS read-only STATUS current DESCRIPTION "The excess information rate Must be >= 0. EIR must be greater than or equal to CIR,if EIR > 0." ::= { fsY1564SlaEntry 16 } fsY1564SlaEBS OBJECT-TYPE SYNTAX Unsigned32 (0..10485760) UNITS "Bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The excess burst size Must be > 0 if EIR > 0." ::= { fsY1564SlaEntry 17 } fsY1564SlaTrafPolicing OBJECT-TYPE SYNTAX INTEGER { on(1), off(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Traffic policing status. If the Trafific policing status is set as off then Traffic polincing test is not triggered for the specified SLA Id.Default Value for this object is on." DEFVAL { 1 } ::= { fsY1564SlaEntry 18 } fsY1564SlaTestSelector OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Test Input to be tested for the Test. A FOUR BYTE integer is used to specify the Test Inputs. Each BIT in the four byte integer represents the tests are to be included in Service Configuration Test. The mapping between the bit positions and the test inputs are as follows: 0 - Simple CIR Validation Test 1 - Step Load CIR Test 2 - EIR Configuration Test, Colour-Aware/Non-Colour-Aware based on the value set for the object fsY1564SlaColormode or fsY1564ServiceConfColorMode. 3 - Traffic Policing Test, Colour-Aware/Non-Colour-Aware based on the value present in the object fsY1564SlaColormode or fsY1564ServiceConfColorMode. The remaining bits are unused. Combination of test inputs are also allowed. For example, if the bits 0 and 3 are set, then the service configuration test is selected with Simple CIR Valdation Test and EIR Configuration Test. The user has to enter the corresponding integer value for the bits set. For Example if the bits 0 (integer value 1) and 3 (Integer value 8) are set, the user has to enter the value 9 in decimal and equivalent Hex value is 9. By default, Simple CIR, Step Load CIR, EIR - Non-Colour-Aware and Traffic policing - Non-Color-Aware tests are selected." DEFVAL { '0000000F'H } ::= { fsY1564SlaEntry 19 } fsY1564SlaCurrentTestMode OBJECT-TYPE SYNTAX Integer32 ( 0..7 ) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the currently running test in service configuration test. The mode will be one of the following 0 - Indicates the no test is in progress 1 - Simple CIR Validation Test 2 - Step Load CIR Test 3 - EIR Configuration Test, Colour-Aware 4 - EIR Configuration Test, Non-Colour-Aware 5 - Traffic Policing Test, Colour-Aware 6 - Traffic Policing Test, Non-Colour-Aware 7 - Performance Test." ::= { fsY1564SlaEntry 20 } fsY1564SlaCurrentTestState OBJECT-TYPE SYNTAX INTEGER { notInitiated (1), -- test not initiated. completed (2), -- test successfully completed. inProgress (3), -- test in progress. aborted (4) -- test aborted. } MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current test state of the SLA." DEFVAL { 1 } ::= { fsY1564SlaEntry 21 } fsY1564SlaRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the row status and is used to create or deletea new entry by setting this object to the appropriate value as mentioned in SMI-v2." ::= { fsY1564SlaEntry 22 } --- *********************************************************************** -- Traffic Profile Table --- *********************************************************************** fsY1564TrafProfTable OBJECT-TYPE SYNTAX SEQUENCE OF FsY1564TrafProfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Traffic Profile configurations." ::= { fsY1564TrafProf 1 } fsY1564TrafProfEntry OBJECT-TYPE SYNTAX FsY1564TrafProfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains information about a particular Traffic Profile configuration." INDEX { fsY1564ContextId, fsY1564TrafProfId } ::= { fsY1564TrafProfTable 1 } FsY1564TrafProfEntry ::= SEQUENCE { fsY1564TrafProfId Unsigned32, fsY1564TrafProfDir INTEGER, fsY1564TrafProfPktSize Integer32, fsY1564TrafProfPayload OCTET STRING, fsY1564TrafProfOptEmixPktSize DisplayString, fsY1564TrafProfPCP IEEE8021PriorityCodePoint, fsY1564TrafProfRowStatus RowStatus } fsY1564TrafProfId OBJECT-TYPE SYNTAX Unsigned32 ( 1..10 ) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the Y1564 Traffic Profile Identifier. This is a free running index." ::= { fsY1564TrafProfEntry 1 } fsY1564TrafProfDir OBJECT-TYPE SYNTAX INTEGER { external (1), internal (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the direction of Y1564 Traffic Profile Generation. When this object is set as external, the traffic is generated at the wire-side of network-to-network interface (NNI) and is transmitted to the responder through the same interface.When this object is set as internal the traffic is generated at the user-to-network interface (UNI) and transmitted to the responder through NNI respectively. Now the direction external(1) only supported." DEFVAL { 1 } ::= { fsY1564TrafProfEntry 2 } fsY1564TrafProfPktSize OBJECT-TYPE SYNTAX Integer32 ( 64..1518 ) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Y1564 Traffic Profile Packet Size in bytes. Allowable frame sizes are 64,128,256,512,1024,1280 and 1518" DEFVAL { 512 } ::= { fsY1564TrafProfEntry 3 } fsY1564TrafProfPayload OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Y1564 Payload in the packet profile." ::= { fsY1564TrafProfEntry 4 } fsY1564TrafProfOptEmixPktSize OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the optional variable-size pattern (EMIX)in bytes for Y1564 Traffic Profile. Frame Sizes and corresponding size desiginations are a - 64, b - 128, c - 256, d - 512,e - 1024, f - 1280 ,g - 1518. The pattern must be a repeating sequence of sizes. For Example, a five frame repeating pattern can be specified as follows ggeaa = 1518, 1518, 1024, 64, 64. Either fsY1564TrafProfPktSize or fsY1564TrafProfOptEmixPktSize can be used for Y1564 Traffic profile. The default pattern for EMIX be the sequence of sizes: abceg" ::= { fsY1564TrafProfEntry 5 } fsY1564TrafProfPCP OBJECT-TYPE SYNTAX IEEE8021PriorityCodePoint MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the priority that is to be inserted in the generated test frames. PCP value is inserted only if the Mep Type is Vlan based Mep." ::= { fsY1564TrafProfEntry 6 } fsY1564TrafProfRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the row status and is used to create or delete a new entry by setting this object to the appropriate value as mentioned in SMI-v2." ::= { fsY1564TrafProfEntry 7 } --- *********************************************************************** -- Service Acceptance Criteria Profile Table --- *********************************************************************** fsY1564SacTable OBJECT-TYPE SYNTAX SEQUENCE OF FsY1564SacEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Service Acceptance Criteria Profile configuration. Service Acceptance Criteria (SAC) is a set of criteria used to ensure that a service meets its functionality and quality requirement and that the service is ready to operate when it has been deployed." ::= { fsY1564Sac 1 } fsY1564SacEntry OBJECT-TYPE SYNTAX FsY1564SacEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains information about a particular SAC Profile configuration." INDEX { fsY1564ContextId, fsY1564SacId } ::= { fsY1564SacTable 1 } FsY1564SacEntry ::= SEQUENCE { fsY1564SacId Unsigned32, fsY1564SacInfoRate Integer32, fsY1564SacFrLossRatio Integer32, fsY1564SacFrTransDelay Integer32, fsY1564SacFrDelayVar Integer32, fsY1564SacAvailability OCTET STRING, fsY1564SacRowStatus RowStatus } fsY1564SacId OBJECT-TYPE SYNTAX Unsigned32 ( 1..10 ) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the Y1564 SAC Identifier used to identify the particular SAC entry." ::= { fsY1564SacEntry 1 } fsY1564SacInfoRate OBJECT-TYPE SYNTAX Integer32 ( 1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Y1564 Information Rate configured as part of this SAC. This is the minimum Information Rate that each services are expected to be met. Information rate is the maximum rate at which none of the offered frames are dropped by the port. It is specified in % of the link's bandwidth." ::= { fsY1564SacEntry 2 } fsY1564SacFrLossRatio OBJECT-TYPE SYNTAX Integer32 ( 0..100 ) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Y1564 Frame Loss Ratio (FLR) configured as part of this SAC. This is the minimum frame loss ratio that each services are expected to be met. Frame Loss Ratio measures the number of packets lost over the total number of packets sent in percentage. Frame loss can be due to a number of issues such as network congestion or errors during transmissions. Example: 50% should be given as 50" ::= { fsY1564SacEntry 3 } fsY1564SacFrTransDelay OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Y1564 Frame Transfer Delay (FTD) configured as part of this SAC. This is the minimum frame transfer delay (in milliseconds) that each services are expected to be met. Frame Transfer delay measures the round-trip time (RTT) taken by a test frame to travel through a network device or across the network and back to the test port " ::= { fsY1564SacEntry 4 } fsY1564SacFrDelayVar OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Y1564 Frame Delay Variation configured as part of this SAC. This is the minimum frame delay variation (in milliseconds) that each services are expected to be met. Frame Delay Variation (FDV) measures the variations in the time delay between packet deliveries." ::= { fsY1564SacEntry 5 } fsY1564SacAvailability OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..6)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Y1564 Availability configured as part of this SAC. This is the maximum avaliablity that each services are expected to be met. Example: 50% should be given as 50.00 39.61% should be given as 39.61 Availability is defined as the percentage of available time (to total time) in a generic observation period." ::= { fsY1564SacEntry 6 } fsY1564SacRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the row status and is used to create or delete a new entry by setting this object to the appropriate value as mentioned in SMI-v2." ::= { fsY1564SacEntry 7 } --- *********************************************************************** -- Service Configuration Table --- *********************************************************************** fsY1564ServiceConfTable OBJECT-TYPE SYNTAX SEQUENCE OF FsY1564ServiceConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Service Configuration information. It includes bandwidth profile parameters, VLAN Index and Interface Index which will be used to create a service when MEF module is not defined." ::= { fsY1564ServiceConf 1 } fsY1564ServiceConfEntry OBJECT-TYPE SYNTAX FsY1564ServiceConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains information about a particular Y1564 Service specific configuration." INDEX { fsY1564ContextId, fsY1564ServiceConfId } ::= { fsY1564ServiceConfTable 1 } FsY1564ServiceConfEntry ::= SEQUENCE { fsY1564ServiceConfId Unsigned32, fsY1564ServiceConfColorMode INTEGER, fsY1564ServiceConfCoupFlag TruthValue, fsY1564ServiceConfCIR Unsigned32, fsY1564ServiceConfCBS Unsigned32, fsY1564ServiceConfEIR Unsigned32, fsY1564ServiceConfEBS Unsigned32, fsY1564ServiceConfRowStatus RowStatus } fsY1564ServiceConfId OBJECT-TYPE SYNTAX Unsigned32 ( 1..10 ) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the Y1564 Service Configuration Identifier. This is a free running index used to identify a Service Configuration." ::= { fsY1564ServiceConfEntry 1 } fsY1564ServiceConfColorMode OBJECT-TYPE SYNTAX INTEGER { colorAware(1), colorBlind(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether the color-aware or color blind property is employed by the bandwidth profile. The default value for this object is ColorBlind." DEFVAL { 2 } ::= { fsY1564ServiceConfEntry 2 } fsY1564ServiceConfCoupFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the modes of operation of the rate enforcement algorithm. The choice of the value for CF has the effect of controlling the volume of the Service Frames that are declared Yellow. When CF is set to 0, the long term average bit rate of Service Frames that are declared Yellow is bounded by EIR. When CF is set to 1, the long term average bit rate of Service Frames that are declared Yellow is bounded by CIR + EIR depending on volume of the offered Service Frames that are declared Green " ::= { fsY1564ServiceConfEntry 3 } fsY1564ServiceConfCIR OBJECT-TYPE SYNTAX Unsigned32 (0..10485760) MAX-ACCESS read-write STATUS current DESCRIPTION "The committed information rate Must be >= 0. CIR must be less than or equal to EIR,if EIR > 0." ::= { fsY1564ServiceConfEntry 4 } fsY1564ServiceConfCBS OBJECT-TYPE SYNTAX Unsigned32 (0..10485760) MAX-ACCESS read-write STATUS current DESCRIPTION "The committed burst size Must be > 0 if CIR > 0. Maximum allowable size will be jumbo frame size." ::= { fsY1564ServiceConfEntry 5 } fsY1564ServiceConfEIR OBJECT-TYPE SYNTAX Unsigned32 (0..10485760) MAX-ACCESS read-write STATUS current DESCRIPTION "The excess information rate Must be >= 0. EIR must be greater than or equal to CIR,if EIR > 0." ::= { fsY1564ServiceConfEntry 6 } fsY1564ServiceConfEBS OBJECT-TYPE SYNTAX Unsigned32 (0..10485760) MAX-ACCESS read-write STATUS current DESCRIPTION "The excess burst size Must be > 0 if EIR > 0." ::= { fsY1564ServiceConfEntry 7 } fsY1564ServiceConfRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the row status and is used to create or delete a new entry by setting this object to the appropriate value as mentioned in SMI-v2." ::= { fsY1564ServiceConfEntry 8 } --- *********************************************************************** -- SLA Configuration Test Report Table --- *********************************************************************** fsY1564ConfigTestReportTable OBJECT-TYPE SYNTAX SEQUENCE OF FsY1564ConfigTestReportEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the statistics of the SLA operation performed." ::= { fsY1564ConfigTest 1 } fsY1564ConfigTestReportEntry OBJECT-TYPE SYNTAX FsY1564ConfigTestReportEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry specifies the statistics about a particular step in the SLA operation performed." INDEX { fsY1564ContextId, fsY1564ConfigTestReportSlaId, fsY1564ConfigTestReportFrSize,fsY1564ConfigTestCurrentTestMode, fsY1564ConfigTestReportStepId } ::= { fsY1564ConfigTestReportTable 1 } FsY1564ConfigTestReportEntry ::= SEQUENCE { fsY1564ConfigTestReportSlaId Unsigned32, fsY1564ConfigTestReportFrSize Integer32, fsY1564ConfigTestCurrentTestMode Integer32, fsY1564ConfigTestReportStepId Integer32, fsY1564ConfigTestReportResult INTEGER, fsY1564ConfigTestReportIrMin Unsigned32, fsY1564ConfigTestReportIrMean Unsigned32, fsY1564ConfigTestReportIrMax Unsigned32, fsY1564ConfigTestReportFrLossCnt Unsigned32, fsY1564ConfigTestReportFrLossRatio Unsigned32, fsY1564ConfigTestReportFrTxDelayMin Unsigned32, fsY1564ConfigTestReportFrTxDelayMean Unsigned32, fsY1564ConfigTestReportFrTxDelayMax Unsigned32, fsY1564ConfigTestReportFrDelayVarMin Unsigned32, fsY1564ConfigTestReportFrDelayVarMean Unsigned32, fsY1564ConfigTestReportFrDelayVarMax Unsigned32, fsY1564ConfigTestReportTestStartTime TimeStamp, fsY1564ConfigTestReportTestEndTime TimeStamp } fsY1564ConfigTestReportSlaId OBJECT-TYPE SYNTAX Unsigned32 ( 1..10 ) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the SLA Id of service configuration test." ::= { fsY1564ConfigTestReportEntry 1 } fsY1564ConfigTestReportFrSize OBJECT-TYPE SYNTAX Integer32 ( 64..1518 ) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the Y1564 frame size in SLA operation statistics." ::= { fsY1564ConfigTestReportEntry 2 } fsY1564ConfigTestCurrentTestMode OBJECT-TYPE SYNTAX Integer32 ( 0..7 ) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the Currently active test running as part of service configuration test." ::= { fsY1564ConfigTestReportEntry 3 } fsY1564ConfigTestReportStepId OBJECT-TYPE SYNTAX Integer32 ( 1..10 ) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the Y1564 Step Index in SLA operation statistics. Step Id for each test as follows. 1. For Simple CIR Validation test, step Id will be one 2. For Step Load CIR, step Id is based on step load rate 3. For EIR Color-Aware, step Id will be one and two. one for green and two for yellow frames. 4. For Traffic Policing Color-Aware, step Id will be one and two. one for green and two for yellow frames. 5. For EIR Non-Color-Aware, step Id will be one. 6. For Traffic Policing Non-Color-Aware, step Id will be one." ::= { fsY1564ConfigTestReportEntry 4 } fsY1564ConfigTestReportResult OBJECT-TYPE SYNTAX INTEGER { pass (1), fail (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This oject specifies the result of Service Configuration Test." ::= { fsY1564ConfigTestReportEntry 5 } fsY1564ConfigTestReportIrMin OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the Minimum value of Information Rate in KBPS for the test." ::= { fsY1564ConfigTestReportEntry 6 } fsY1564ConfigTestReportIrMean OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the Mean value of Information Rate in KBPS for the test." ::= { fsY1564ConfigTestReportEntry 7 } fsY1564ConfigTestReportIrMax OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the Maximum value of Information Rate in KBPS for the test." ::= { fsY1564ConfigTestReportEntry 8 } fsY1564ConfigTestReportFrLossCnt OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of frames lost during the test." ::= { fsY1564ConfigTestReportEntry 9 } fsY1564ConfigTestReportFrLossRatio OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Frame Loss Ratio observed during the test." ::= { fsY1564ConfigTestReportEntry 10 } fsY1564ConfigTestReportFrTxDelayMin OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Minimum Frame Transfer Delay observed during the test." ::= { fsY1564ConfigTestReportEntry 11 } fsY1564ConfigTestReportFrTxDelayMean OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Mean Frame Transfer Delay observed during the test." ::= { fsY1564ConfigTestReportEntry 12 } fsY1564ConfigTestReportFrTxDelayMax OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Maximum Frame Transfer Delay observed during the test." ::= { fsY1564ConfigTestReportEntry 13 } fsY1564ConfigTestReportFrDelayVarMin OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Minimum Frame Delay Variation observed during the test." ::= { fsY1564ConfigTestReportEntry 14 } fsY1564ConfigTestReportFrDelayVarMean OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Mean Frame Delay Variation observed during the test." ::= { fsY1564ConfigTestReportEntry 15 } fsY1564ConfigTestReportFrDelayVarMax OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Maximum Frame Delay Variation observed during the test." ::= { fsY1564ConfigTestReportEntry 16 } fsY1564ConfigTestReportTestStartTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the service start time of the test in Y1564 for Service configuration test." ::= { fsY1564ConfigTestReportEntry 17 } fsY1564ConfigTestReportTestEndTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the service end time of the test in Y1564 for Service configuration test." ::= { fsY1564ConfigTestReportEntry 18 } --- *********************************************************************** -- Sevice Performance Table --- *********************************************************************** fsY1564PerformanceTestTable OBJECT-TYPE SYNTAX SEQUENCE OF FsY1564PerformanceTestEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Service performance test related information. Each entry in this table corresponds to a configured SLA entry in fsy1564SlaTable. Entry in this table has to be created explicitly." ::= { fsY1564PerformanceTest 1 } fsY1564PerformanceTestEntry OBJECT-TYPE SYNTAX FsY1564PerformanceTestEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains information about a particular Y1564 performance specific configuration." INDEX { fsY1564ContextId, fsY1564PerformanceTestIndex } ::= { fsY1564PerformanceTestTable 1 } FsY1564PerformanceTestEntry ::= SEQUENCE { fsY1564PerformanceTestIndex Unsigned32, fsY1564PerformanceTestSlaList OCTET STRING, fsY1564PerformanceTestDuration INTEGER, fsY1564PerformanceTestStatus INTEGER, fsY1564PerformanceTestRowStatus RowStatus } fsY1564PerformanceTestIndex OBJECT-TYPE SYNTAX Unsigned32 ( 1..10 ) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the Y1564 performance test Identifier. This is a free running index used to identify a service performance test." ::= { fsY1564PerformanceTestEntry 1 } fsY1564PerformanceTestSlaList OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..10)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the SLA lists to be tested in Y1564 for Service performance test. Example: SLA 1, 2, 3, 5, 7, 10 should be given as 1-2-3-5-7-10" ::= { fsY1564PerformanceTestEntry 2 } fsY1564PerformanceTestDuration OBJECT-TYPE SYNTAX INTEGER { interval15min (1), interval2hour (2), interval24hour (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the period to complete Service Performance Test.The default interval for this object is 2 hours." DEFVAL { 2 } ::= { fsY1564PerformanceTestEntry 3 } fsY1564PerformanceTestStatus OBJECT-TYPE SYNTAX INTEGER { start(1), stop(2)} MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the Y1564 Service Performance test initiation status. An enumerated value set to 'start' initiates service performance test will be started for the SLA lists specified in object fsY1564PerfSlaList." DEFVAL { 2 } ::= { fsY1564PerformanceTestEntry 4 } fsY1564PerformanceTestRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Denotes the Row status of the service performance test entry. This object specifies the row status and is used to create or delete a new entry by setting this object to the appropriate value as mentioned in SMI-v2." ::= { fsY1564PerformanceTestEntry 5 } --- *********************************************************************** -- SLA Performance Test Report Table --- *********************************************************************** fsY1564PerfTestReportTable OBJECT-TYPE SYNTAX SEQUENCE OF FsY1564PerfTestReportEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the statistics of the SLA operation performed." ::= { fsY1564PerfTestReport 1 } fsY1564PerfTestReportEntry OBJECT-TYPE SYNTAX FsY1564PerfTestReportEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry specifies the statistics about a particular step in the SLA operation performed." INDEX { fsY1564ContextId, fsY1564SlaId, fsY1564PerformanceTestIndex, fsY1564PerfTestReportFrSize } ::= { fsY1564PerfTestReportTable 1 } FsY1564PerfTestReportEntry ::= SEQUENCE { fsY1564PerfTestReportFrSize Integer32, fsY1564PerfTestReportResult INTEGER, fsY1564PerfTestReportIrMin Unsigned32, fsY1564PerfTestReportIrMean Unsigned32, fsY1564PerfTestReportIrMax Unsigned32, fsY1564PerfTestReportFrLossCnt Unsigned32, fsY1564PerfTestReportFrLossRatio Unsigned32, fsY1564PerfTestReportFrTxDelayMin Unsigned32, fsY1564PerfTestReportFrTxDelayMean Unsigned32, fsY1564PerfTestReportFrTxDelayMax Unsigned32, fsY1564PerfTestReportFrDelayVarMin Unsigned32, fsY1564PerfTestReportFrDelayVarMean Unsigned32, fsY1564PerfTestReportFrDelayVarMax Unsigned32, fsY1564PerfTestReportAvailability OCTET STRING, fsY1564PerfTestReportUnavailableCount Unsigned32, fsY1564PerfTestReportTestStartTime TimeStamp, fsY1564PerfTestReportTestEndTime TimeStamp } fsY1564PerfTestReportFrSize OBJECT-TYPE SYNTAX Integer32 ( 64..1518 ) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the frame size in SLA performance test statistics." ::= { fsY1564PerfTestReportEntry 1 } fsY1564PerfTestReportResult OBJECT-TYPE SYNTAX INTEGER { pass (1), fail (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This oject specifies the result of service Performance Test." ::= { fsY1564PerfTestReportEntry 2 } fsY1564PerfTestReportIrMin OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the Minimum value of Information Rate in KBPS for the test." ::= { fsY1564PerfTestReportEntry 3 } fsY1564PerfTestReportIrMean OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the Mean value of Information Rate in KBPS for the test." ::= { fsY1564PerfTestReportEntry 4 } fsY1564PerfTestReportIrMax OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the Maximum value of Information Rate in KBPS for the test." ::= { fsY1564PerfTestReportEntry 5 } fsY1564PerfTestReportFrLossCnt OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of frames lost during the test." ::= { fsY1564PerfTestReportEntry 6 } fsY1564PerfTestReportFrLossRatio OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Frame Loss Ratio observed during the test." ::= { fsY1564PerfTestReportEntry 7 } fsY1564PerfTestReportFrTxDelayMin OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Minimum Frame Transfer Delay observed during the test." ::= { fsY1564PerfTestReportEntry 8 } fsY1564PerfTestReportFrTxDelayMean OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Mean Frame Transfer Delay observed during the test." ::= { fsY1564PerfTestReportEntry 9 } fsY1564PerfTestReportFrTxDelayMax OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Maximum Frame Transfer Delay observed during the test." ::= { fsY1564PerfTestReportEntry 10 } fsY1564PerfTestReportFrDelayVarMin OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Minimum Frame Delay Variation observed during the test." ::= { fsY1564PerfTestReportEntry 11 } fsY1564PerfTestReportFrDelayVarMean OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Mean Frame Delay Variation observed during the test." ::= { fsY1564PerfTestReportEntry 12 } fsY1564PerfTestReportFrDelayVarMax OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Maximum Frame Delay Variation observed during the test." ::= { fsY1564PerfTestReportEntry 13 } fsY1564PerfTestReportAvailability OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..6)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Availability of the service during the test." ::= { fsY1564PerfTestReportEntry 14 } fsY1564PerfTestReportUnavailableCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Unavailable frame count during the test." ::= { fsY1564PerfTestReportEntry 15 } fsY1564PerfTestReportTestStartTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the service start time of the test in Y1564 for Service performance test." ::= { fsY1564PerfTestReportEntry 16 } fsY1564PerfTestReportTestEndTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the service end time of the test in Y1564 for Service performance test." ::= { fsY1564PerfTestReportEntry 17 } --- *********************************************************************** -- Notification --- *********************************************************************** fsY1564Traps OBJECT IDENTIFIER ::= { fsY1564Notification 0 } fsY1564TrapObjects OBJECT IDENTIFIER ::= { fsY1564Notification 1 } fsY1564TrapSlaId OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object refers to the SLA Id on which the Y1564 is enabled. And will be used in sending the failure Traps." ::= { fsY1564TrapObjects 1 } fsY1564TypeOfFailure OBJECT-TYPE SYNTAX DisplayString (SIZE (1..32)) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object provides the text indicating a particular failure condition. 'Unrecoverable/Transaction failure' will be set, when the below defectes are detected by CFM when any of the Service configuration or Performance tests are in progress. These defect Conditions are: RdiCondition - The MEP has encountered remote MEP defect condition. LossOfContinuity - The MEP has encountered loss of continuity defect condition." ::= { fsY1564TrapObjects 2 } fsY1564FailureTrap NOTIFICATION-TYPE OBJECTS { fsY1564ContextName, fsY1564TrapSlaId, fsY1564TypeOfFailure } STATUS current DESCRIPTION "This trap is generated when there is any failure on a link." ::= { fsY1564Traps 1 } END