-- Copyright (C) 2009-2012 Aricent Group . All Rights Reserved -- /***************************************************************** -- * * -- * $RCSfile: fsmirtm6.mib,v $ * -- * * -- * $Date: 2015/10/19 12:19:52 $ * -- * * -- * $Revision: 1.7 $ * -- * * -- ****************************************************************/ ARICENT-RTM6MI-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE, MODULE-IDENTITY, IpAddress, Integer32, Unsigned32, enterprises FROM SNMPv2-SMI RowStatus FROM SNMPv2-TC; fsMIRtm6 MODULE-IDENTITY LAST-UPDATED "201209050000Z" ORGANIZATION "ARICENT COMMUNICATIONS SOFTWARE" CONTACT-INFO "support@aricent.com" DESCRIPTION " This mib module is for RTMv6 module with virtual routing and forwarding support" REVISION "201209050000Z" DESCRIPTION " This mib module is for RTMv6 module with virtual routing and forwarding support" ::= { enterprises aricent-communication-holding-ltd(29601) iss(2) 32} fsMIRtm6Scalar OBJECT IDENTIFIER ::= { fsMIRtm6 1 } -- RTMv6 SCALAR VARIABLE fsMIRtm6GlobalTrace OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This is a global RTMv6 trace and not specific to any RTMv6 context. Enables the tracing in the selected submodule in RTM6. A 32 bit integer is used to store the Tracing level in the specified module. Different Tracing Levels - BIT 0 - Initialisation and Shutdown Trace. BIT 1 - Management trace. BIT 2 - Data path trace. BIT 3 - Control Plane trace. BIT 5 - All Failure trace. The remaining bits are unused.The combination of levels and submodules are allowed i.e. Tracing can be allowed at all failure and data path level in All submodules by setting the BIT appropriately." ::= { fsMIRtm6Scalar 1 } fsMIRtm6ThrotLimit OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "In RTM6 operations which hogs CPU for a long time are being throttled. These events will process only limited number of routes set by this object for each iteration. Typically, the values used shall be in the range 1..65535" DEFVAL { 1000 } ::= { fsMIRtm6Scalar 2 } fsMIRtm6MaximumBgpRoutes OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This Object configures the number of BGP routes to be programmed in RTM6" ::= { fsMIRtm6Scalar 3 } fsMIRtm6MaximumOspfRoutes OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This Object configures the number of OSPF routes to be programmed in RTM6" ::= { fsMIRtm6Scalar 4 } fsMIRtm6MaximumRipRoutes OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This Object configures the number of RIP routes to be programmed in RTM6" ::= { fsMIRtm6Scalar 5 } fsMIRtm6MaximumStaticRoutes OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This Object configures the number of STATIC routes to be programmed in RTM6" ::= { fsMIRtm6Scalar 6 } fsMIRtm6MaximumISISRoutes OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This Object configures the number of ISIS routes to be programmed in RTM6" ::= { fsMIRtm6Scalar 7 } -- RTMv6 Table fsMIRtm6Table OBJECT-TYPE SYNTAX SEQUENCE OF FsMIRtm6Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information describing the parameters of RTMv6's Virtual context" ::= { fsMIRtm6 2 } fsMIRtm6Entry OBJECT-TYPE SYNTAX FsMIRtm6Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information describing the parameters of one of the RTMv6's virtual context" INDEX { fsMIRtm6ContextId } ::= { fsMIRtm6Table 1 } FsMIRtm6Entry ::= SEQUENCE { fsMIRtm6ContextId Integer32, fsMIRrd6RouterId IpAddress, fsMIRrd6FilterByOspfTag INTEGER, fsMIRrd6FilterOspfTag Integer32, fsMIRrd6FilterOspfTagMask Integer32, fsMIRrd6RouterASNumber Integer32, fsMIRrd6AdminStatus INTEGER, fsMIRrd6Trace Unsigned32, fsMIRtm6StaticRouteDistance Integer32 } fsMIRtm6ContextId OBJECT-TYPE SYNTAX Integer32 (0..127) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A 32-bit unique context id identifing the RTMv6 virtual Context Minimum value of context ID is 0 (this is for defualt Virtual context. The Max context ID is system dependent and the value is taken care in virtual context manager MIB" ::= { fsMIRtm6Entry 1 } fsMIRrd6RouterId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The 4-byte Identifier value that uniquely identifies the router in its operational environment. This can be set only if the fsMIRrd6AdminStatus is disabled. Router ID is configured for each RTMv6 Virtual context" ::= { fsMIRtm6Entry 2 } fsMIRrd6FilterByOspfTag OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "To enable distribution of routes based on the tag value (ref RFC1745 sec 2.1). This filter takes precedence over the common RRD6 control table." DEFVAL { disable } ::= { fsMIRtm6Entry 3 } fsMIRrd6FilterOspfTag OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The tag based on which routes have to be filtered for export to routing protocols" ::= { fsMIRtm6Entry 4 } fsMIRrd6FilterOspfTagMask OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The bitmask to be applied to fsMIRrd6FilterOspfTag for comparison. This bitmask specifies the fields of the OSPF tag to be considered for filtering." DEFVAL { -1 } ::= { fsMIRtm6Entry 5 } fsMIRrd6RouterASNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The Autonomous system number in which this router is running." DEFVAL { 0 } ::= { fsMIRtm6Entry 6 } fsMIRrd6AdminStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The Admin status of the RTMv6 virtual context. This object can be set to enabled only after setting the AS number and the Router ID to a valid value." DEFVAL { disabled } ::= { fsMIRtm6Entry 7 } fsMIRrd6Trace OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This is used to define the trace level in each RTMv6 virtual context. Enables the tracing in the selected submodule in RTM6v6 context. A 32 bit integer is used to store the Tracing level in the specified module. Different Tracing Levels - BIT 0 - Initialisation and Shutdown Trace. BIT 1 - Management trace. BIT 2 - Data path trace. BIT 3 - Control Plane trace. BIT 4 - OS Resource trace. BIT 5 - All Failure trace. The remaining bits are unused.The combination of levels and submodules are allowed i.e. Tracing can be allowed at all failure and data path level in All submodules by setting the BIT appropriately." ::= { fsMIRtm6Entry 8 } fsMIRtm6StaticRouteDistance OBJECT-TYPE SYNTAX Integer32(1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the default administrative distance for IPv6 static routes" ::= { fsMIRtm6Entry 9 } fsMIRrd6ControlTable OBJECT-TYPE SYNTAX SEQUENCE OF FsMIRrd6ControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Control Table for configuring routes allowed/denied for export in the RTMv6 virtual Context." ::= { fsMIRtm6 3 } fsMIRrd6ControlEntry OBJECT-TYPE SYNTAX FsMIRrd6ControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of fsMIRrd6ControlTable." INDEX { fsMIRtm6ContextId, fsMIRrd6ControlDestIpAddress, fsMIRrd6ControlNetMaskLen } ::= { fsMIRrd6ControlTable 1 } FsMIRrd6ControlEntry ::= SEQUENCE { fsMIRrd6ControlDestIpAddress OCTET STRING, fsMIRrd6ControlNetMaskLen Integer32, fsMIRrd6ControlSourceProto INTEGER, fsMIRrd6ControlDestProto Integer32, fsMIRrd6ControlRouteExportFlag INTEGER, fsMIRrd6ControlRowStatus RowStatus } fsMIRrd6ControlDestIpAddress OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The destination IPv6 address of this route." ::= { fsMIRrd6ControlEntry 1 } fsMIRrd6ControlNetMaskLen OBJECT-TYPE SYNTAX Integer32 (1 .. 128) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Indicate the prefix len and the derived reverse mask should be logical-ANDed with the destination address. The mask is also used to specify the range of IP addresses. For Eg: Destination Net = 128:11:: and Net Mask Len = 32 (::255:255:255:255) specifies the range of routes starting from 128:11:: to 121:11::255:255:255:255 For specifying all routes give Destination Net = ::0 and Net Mask Len = 128" ::= { fsMIRrd6ControlEntry 2 } fsMIRrd6ControlSourceProto OBJECT-TYPE SYNTAX INTEGER { all (0), -- any protocol other (1), -- none of the following local (2), -- interface entries netmgmt (3), -- static route ndisc (4), -- Redirect Routes rip (5), -- RIPng ospf (6), -- Open Shortest Path First bgp (7), -- Border Gateway Protocol idrp (8), -- InterDomain Routing Protocol igrp (9) -- InterGateway Routing Protocol } MAX-ACCESS read-write STATUS current DESCRIPTION "The Identifier of the source routing protocol. A value of zero will be interpreted as 'any', which matches route from all protocols. This object should be set before fsMIRrd6ControlRouteExportFlag is configured. For an ALL ROUTE entry, this value must be always 0" DEFVAL { 0 } ::= { fsMIRrd6ControlEntry 3} fsMIRrd6ControlDestProto OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The identifier of the destination routing protocol. This field is a bit mask, a 1 indicates that the route has to be exported to the routing protocol corresponding to the bit-position. +---------------------------------------------------+ | reserved | reserved | reserved | reserved | +---------------------------------------------------+ | 15 | 14 | 13 | 12 | +---------------------------------------------------+ | reserved | reserved | reserved | igrp | +---------------------------------------------------+ | 11 | 10 | 9 | 8 | +---------------------------------------------------+ | idrp | bgp | ospf | rip | +---------------------------------------------------+ | 7 | 6 | 5 | 4 | +---------------------------------------------------+ | ndisc | netmgmt | local | other | +---------------------------------------------------+ | 3 | 2 | 1 | 0 | +---------------------------------------------------+ A value of zero will be interpreted as 'any', which matches route destinated to all protocols. This object should be set before fsMIRrd6ControlRouteExportFlag is configured. For an ALL ROUTE entry, this value must be always 0." DEFVAL { 0 } ::= { fsMIRrd6ControlEntry 4} fsMIRrd6ControlRouteExportFlag OBJECT-TYPE SYNTAX INTEGER { permit (1), deny (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This flag specifies whether the route is allowed for export or denied. If the ALL ROUTE entry has this value as permit, then all other entries can be set only as deny and vice-versa. Changing the status of the ALL ROUTE entry is possible only when there is no other filter configuration exists." ::= { fsMIRrd6ControlEntry 5} fsMIRrd6ControlRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of this row by which a new row can be created or deleted according to the SMIv2 conventions. The values supported for set operation are - createandwait, active, destroy. Creation/Deletion of the ALL ROUTE entry is possible only when there is no other filter configuration exists." ::= { fsMIRrd6ControlEntry 6 } --Routing Protocol Registration table. fsMIRrd6RoutingProtoTable OBJECT-TYPE SYNTAX SEQUENCE OF FsMIRrd6RoutingProtoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Registration Table for the different routing protocols. This table is read-only and reflects the information of routing protocols held by the Route Table Manager." ::= { fsMIRtm6 4 } fsMIRrd6RoutingProtoEntry OBJECT-TYPE SYNTAX FsMIRrd6RoutingProtoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in to the fsMIRrd6RoutingProtoTable." INDEX { fsMIRtm6ContextId, fsMIRrd6RoutingProtoId } ::= { fsMIRrd6RoutingProtoTable 1 } FsMIRrd6RoutingProtoEntry ::= SEQUENCE { fsMIRrd6RoutingProtoId INTEGER, fsMIRrd6RoutingRegnId Integer32, fsMIRrd6RoutingProtoTaskIdent OCTET STRING, fsMIRrd6RoutingProtoQueueIdent OCTET STRING, fsMIRrd6AllowOspfAreaRoutes INTEGER, fsMIRrd6AllowOspfExtRoutes INTEGER } fsMIRrd6RoutingProtoId OBJECT-TYPE SYNTAX INTEGER { other (1), -- none of the following local (2), -- interface entries netmgmt (3), -- static route ndisc (4), -- Redirect Routes rip (5), -- RIPng ospf (6), -- Open Shortest Path First bgp (7), -- Border Gateway Protocol idrp (8), -- InterDomain Routing Protocol igrp (9) -- InterGateway Routing Protocol } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Identifier of the routing protocol registered with the routing table manager" ::= { fsMIRrd6RoutingProtoEntry 1 } fsMIRrd6RoutingRegnId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Registeration ID assigned by the RTM for this Routing Protocol " ::= { fsMIRrd6RoutingProtoEntry 2 } fsMIRrd6RoutingProtoTaskIdent OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The Name/Identifier of the Routing Task" ::= { fsMIRrd6RoutingProtoEntry 3 } fsMIRrd6RoutingProtoQueueIdent OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The Name/Identifier of the Message Queue to which messages to the Routing Task are posted." ::= { fsMIRrd6RoutingProtoEntry 4 } fsMIRrd6AllowOspfAreaRoutes OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "A single configuration to PERMIT all OSPF inter-area and intra-area address/mask pairs to be exported into this routing protocol. This configuration takes precedence over filtering based on the control table. " DEFVAL { disable } ::= { fsMIRrd6RoutingProtoEntry 5 } fsMIRrd6AllowOspfExtRoutes OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "A single configuration to PERMIT all OSPF Type 1 and Type 2 Exteral address/mask pairs to be exported into this routing protocol. This configuration together with the control table, take care of selective route export." DEFVAL { disable } ::= { fsMIRrd6RoutingProtoEntry 6 } fsMIRtm6RedTest OBJECT IDENTIFIER ::= { fsMIRtm6 5 } -- RTM6_RED TIME Group -- This group defines objects for RTM6_RED TIME. fsMIRtm6RedEntryTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Time when the node starts entering active state from standby state " ::= { fsMIRtm6RedTest 1 } fsMIRtm6RedExitTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Time when the node completes entering active state from standby state " ::= { fsMIRtm6RedTest 2 } END