-- Copyright (C) 2006-2012 Aricent Group . All Rights Reserved -- $Id: fspimstd.mib,v 1.10 2013/03/20 13:25:19 siva Exp $ ARICENT-PIMCMN2-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32, IpAddress, TimeTicks, Gauge32, Counter32, enterprises FROM SNMPv2-SMI TEXTUAL-CONVENTION, RowStatus, TruthValue, DisplayString FROM SNMPv2-TC InetAddressType, InetAddress FROM INET-ADDRESS-MIB InterfaceIndex FROM IF-MIB MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF; fsPimStdMIB MODULE-IDENTITY LAST-UPDATED "201209050000Z" ORGANIZATION "ARICENT COMMUNICATIONS SOFTWARE" CONTACT-INFO "support@aricent.com" DESCRIPTION "The MIB module for management of PIM Routers Initial Version" REVISION "201209050000Z" DESCRIPTION "The MIB module for management of PIM Routers Initial Version" ::= { enterprises futuresoftware (2076) 114 } fsPimStdMIBObjects OBJECT IDENTIFIER ::= { fsPimStdMIB 1 } fsPimStdScalars OBJECT IDENTIFIER ::= { fsPimStdMIBObjects 1 } fsPimStdTables OBJECT IDENTIFIER ::= { fsPimStdMIBObjects 2 } fsPimStdJoinPruneInterval OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The default interval at which periodic PIM-SM Join/Prune messages are to be sent." ::= { fsPimStdScalars 1 } -- The PIM Interface Table fsPimStdInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPimStdInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the router's PIM interfaces. IGMP and PIM are enabled on all interfaces listed in this table." ::= { fsPimStdTables 1 } fsPimStdInterfaceEntry OBJECT-TYPE SYNTAX FsPimStdInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimInterfaceTable." INDEX { fsPimStdInterfaceIfIndex, fsPimStdInterfaceAddrType} ::= { fsPimStdInterfaceTable 1 } FsPimStdInterfaceEntry ::= SEQUENCE { fsPimStdInterfaceIfIndex Integer32, fsPimStdInterfaceAddrType InetAddressType, fsPimStdInterfaceAddress InetAddress, fsPimStdInterfaceNetMaskLen Integer32, fsPimStdInterfaceMode INTEGER, fsPimStdInterfaceDR InetAddress, fsPimStdInterfaceHelloInterval Integer32, fsPimStdInterfaceStatus RowStatus, fsPimStdInterfaceJoinPruneInterval Integer32, fsPimStdInterfaceCBSRPreference Integer32 } fsPimStdInterfaceIfIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex value of this PIM interface." ::= { fsPimStdInterfaceEntry 1 } fsPimStdInterfaceAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address type of the PIM Interface for which this entry contains information." ::= { fsPimStdInterfaceEntry 2 } fsPimStdInterfaceAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the PIM interface." ::= { fsPimStdInterfaceEntry 3 } fsPimStdInterfaceNetMaskLen OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The network mask for the IP address of the PIM interface." ::= { fsPimStdInterfaceEntry 4 } fsPimStdInterfaceMode OBJECT-TYPE SYNTAX INTEGER { dense(1), sparse(2), sparseDense(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The configured mode of this PIM interface. A value of sparseDense is only valid for PIMv1." DEFVAL { dense } ::= { fsPimStdInterfaceEntry 5 } fsPimStdInterfaceDR OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Designated Router on this PIM interface. For point-to- point interfaces, this object has the value 0.0.0.0." ::= { fsPimStdInterfaceEntry 6 } fsPimStdInterfaceHelloInterval OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The frequency at which PIM Hello messages are transmitted on this interface." DEFVAL { 30 } ::= { fsPimStdInterfaceEntry 7 } fsPimStdInterfaceStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this entry. Creating the entry enables PIM on the interface; destroying the entry disables PIM on the interface." ::= { fsPimStdInterfaceEntry 8 } fsPimStdInterfaceJoinPruneInterval OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The frequency at which PIM Join/Prune messages are transmitted on this PIM interface. The default value of this object is the pimJoinPruneInterval." ::= { fsPimStdInterfaceEntry 9 } fsPimStdInterfaceCBSRPreference OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The preference value for the local interface as a candidate bootstrap router. The value of -1 is used to indicate that the local interface is not a candidate BSR interface." DEFVAL { 0 } ::= { fsPimStdInterfaceEntry 10 } -- The PIM Neighbor Table fsPimStdNeighborTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPimStdNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the router's PIM neighbors." ::= { fsPimStdTables 2 } fsPimStdNeighborEntry OBJECT-TYPE SYNTAX FsPimStdNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimNeighborTable." INDEX { fsPimStdNeighborAddrType, fsPimStdNeighborAddress } ::= { fsPimStdNeighborTable 1 } FsPimStdNeighborEntry ::= SEQUENCE { fsPimStdNeighborAddrType InetAddressType, fsPimStdNeighborAddress InetAddress, fsPimStdNeighborIfIndex Integer32, fsPimStdNeighborUpTime TimeTicks, fsPimStdNeighborExpiryTime TimeTicks, fsPimStdNeighborMode INTEGER } fsPimStdNeighborAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address Type of the PIM neighbor for which this entry contains information." ::= { fsPimStdNeighborEntry 1 } fsPimStdNeighborAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of the PIM neighbor for which this entry contains information." ::= { fsPimStdNeighborEntry 2 } fsPimStdNeighborIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of ifIndex for the interface used to reach this PIM neighbor." ::= { fsPimStdNeighborEntry 3 } fsPimStdNeighborUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time since this PIM neighbor (last) became a neighbor of the local router." ::= { fsPimStdNeighborEntry 4 } fsPimStdNeighborExpiryTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum time remaining before this PIM neighbor will be aged out." ::= { fsPimStdNeighborEntry 5 } fsPimStdNeighborMode OBJECT-TYPE SYNTAX INTEGER { dense(1), sparse(2) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The active PIM mode of this neighbor. This object is deprecated for PIMv2 routers since all neighbors on the interface must be either dense or sparse as determined by the protocol running on the interface." ::= { fsPimStdNeighborEntry 6 } -- -- The PIM IP Multicast Route Table -- fsPimStdIpMRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPimStdIpMRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing PIM-specific information on a subset of the rows of the ipMRouteTable defined in the IP Multicast MIB." ::= { fsPimStdTables 3 } fsPimStdIpMRouteEntry OBJECT-TYPE SYNTAX FsPimStdIpMRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimIpMRouteTable. There is one entry per entry in the ipMRouteTable whose incoming interface is running PIM." INDEX { fsPimStdIpMRouteAddrType, fsPimStdIpMRouteGroup, fsPimStdIpMRouteSource, fsPimStdIpMRouteSourceMaskLen } ::= { fsPimStdIpMRouteTable 1 } FsPimStdIpMRouteEntry ::= SEQUENCE { fsPimStdIpMRouteAddrType InetAddressType, fsPimStdIpMRouteGroup InetAddress, fsPimStdIpMRouteSource InetAddress, fsPimStdIpMRouteSourceMaskLen Integer32, fsPimStdIpMRouteUpstreamAssertTimer TimeTicks, fsPimStdIpMRouteAssertMetric Integer32, fsPimStdIpMRouteAssertMetricPref Integer32, fsPimStdIpMRouteAssertRPTBit TruthValue, fsPimStdIpMRouteFlags BITS } fsPimStdIpMRouteAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP family in which the route belongs to." ::= { fsPimStdIpMRouteEntry 2 } fsPimStdIpMRouteGroup OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP multicast group address for which this entry contains multicast routing information." ::= { fsPimStdIpMRouteEntry 3 } fsPimStdIpMRouteSource OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The network address which when combined with the corresponding value of ipMRouteSourceMask identifies the sources for which this entry contains multicast routing information." ::= { fsPimStdIpMRouteEntry 4 } fsPimStdIpMRouteSourceMaskLen OBJECT-TYPE SYNTAX Integer32(0..128) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The network mask which when combined with the corresponding value of ipMRouteSource identifies the sources for which this entry contains multicast routing information." ::= { fsPimStdIpMRouteEntry 5 } fsPimStdIpMRouteUpstreamAssertTimer OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time remaining before the router changes its upstream neighbor back to its RPF neighbor. This timer is called the Assert timer in the PIM Sparse and Dense mode specification. A value of 0 indicates that no Assert has changed the upstream neighbor away from the RPF neighbor." ::= { fsPimStdIpMRouteEntry 6 } fsPimStdIpMRouteAssertMetric OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The metric advertised by the assert winner on the upstream interface, or 0 if no such assert is in received." ::= { fsPimStdIpMRouteEntry 7 } fsPimStdIpMRouteAssertMetricPref OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The preference advertised by the assert winner on the upstream interface, or 0 if no such assert is in effect." ::= { fsPimStdIpMRouteEntry 8 } fsPimStdIpMRouteAssertRPTBit OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the RPT-bit advertised by the assert winner on the upstream interface, or false if no such assert is in effect." ::= { fsPimStdIpMRouteEntry 9 } fsPimStdIpMRouteFlags OBJECT-TYPE SYNTAX BITS { rpt(0), spt(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes PIM-specific flags related to a multicast state entry. See the PIM Sparse Mode specification for the meaning of the RPT and SPT bits." ::= { fsPimStdIpMRouteEntry 10 } -- -- The PIM Next Hop Table -- fsPimStdIpMRouteNextHopTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPimStdIpMRouteNextHopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing PIM-specific information on a subset of the rows of the ipMRouteNextHopTable defined in the IP Multicast MIB." ::= { fsPimStdTables 4 } fsPimStdIpMRouteNextHopEntry OBJECT-TYPE SYNTAX FsPimStdIpMRouteNextHopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimIpMRouteNextHopTable. There is one entry per entry in the ipMRouteNextHopTable whose interface is running PIM and whose ipMRouteNextHopState is pruned(1)." INDEX { fsPimStdIpMRouteNextHopAddrType, fsPimStdIpMRouteNextHopGroup, fsPimStdIpMRouteNextHopSource, fsPimStdIpMRouteNextHopSourceMaskLen, fsPimStdIpMRouteNextHopIfIndex, fsPimStdIpMRouteNextHopAddress } ::= { fsPimStdIpMRouteNextHopTable 1 } FsPimStdIpMRouteNextHopEntry ::= SEQUENCE { fsPimStdIpMRouteNextHopAddrType InetAddressType, fsPimStdIpMRouteNextHopGroup InetAddress, fsPimStdIpMRouteNextHopSource InetAddress, fsPimStdIpMRouteNextHopSourceMaskLen Integer32, fsPimStdIpMRouteNextHopIfIndex Integer32, fsPimStdIpMRouteNextHopAddress InetAddress, fsPimStdIpMRouteNextHopPruneReason INTEGER } fsPimStdIpMRouteNextHopAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP family in which the Next hop address belongs to." ::= { fsPimStdIpMRouteNextHopEntry 2 } fsPimStdIpMRouteNextHopGroup OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP multicast group for which this entry specifies a next-hop on an outgoing interface." ::= { fsPimStdIpMRouteNextHopEntry 3 } fsPimStdIpMRouteNextHopSource OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The network address which when combined with the corresponding value of fsPimCmnIpMRouteNextHopSourceMask identifies the sources for which this entry specifies a next-hop on an outgoing interface." ::= { fsPimStdIpMRouteNextHopEntry 4 } fsPimStdIpMRouteNextHopSourceMaskLen OBJECT-TYPE SYNTAX Integer32(0..128) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The network mask which when combined with the corresponding value of fsPimCmnIpMRouteNextHopSource identifies the sources for which this entry specifies a next-hop on an outgoing interface" ::= { fsPimStdIpMRouteNextHopEntry 5 } fsPimStdIpMRouteNextHopIfIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex value of the interface for the outgoing interface for this next-hop." ::= { fsPimStdIpMRouteNextHopEntry 6 } fsPimStdIpMRouteNextHopAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address of the next-hop specific to this entry. For most interfaces, this is identical to fsPimCmnIpMRouteNextHopGroup. NBMA interfaces, however, may have multiple next-hop addresses out a single outgoing interface." ::= { fsPimStdIpMRouteNextHopEntry 7 } fsPimStdIpMRouteNextHopPruneReason OBJECT-TYPE SYNTAX INTEGER { other (1), prune (2), assert (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates why the downstream interface was pruned, whether in response to a PIM prune message or due to PIM Assert processing." ::= { fsPimStdIpMRouteNextHopEntry 8 } -- The PIM RP Table fsPimStdRPTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPimStdRPEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The (conceptual) table listing PIM version 1 information for the Rendezvous Points (RPs) for IP multicast groups. This table is deprecated since its function is replaced by the pimRPSetTable for PIM version 2." ::= { fsPimStdTables 5 } fsPimStdRPEntry OBJECT-TYPE SYNTAX FsPimStdRPEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "An entry (conceptual row) in the pimRPTable. There is one entry per RP address for each IP multicast group." INDEX { fsPimStdRPAddrType, fsPimStdRPGroupAddress, fsPimStdRPAddress } ::= { fsPimStdRPTable 1 } FsPimStdRPEntry ::= SEQUENCE { fsPimStdRPAddrType InetAddressType, fsPimStdRPGroupAddress InetAddress, fsPimStdRPAddress InetAddress, fsPimStdRPState INTEGER, fsPimStdRPStateTimer TimeTicks, fsPimStdRPLastChange TimeTicks, fsPimStdRPRowStatus RowStatus } fsPimStdRPAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP Address type in which the multicast group address, and RP address belong to." ::= { fsPimStdRPEntry 1 } fsPimStdRPGroupAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The IP multicast group address for which this entry contains information about an RP." ::= { fsPimStdRPEntry 2 } fsPimStdRPAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The unicast address of the RP." ::= { fsPimStdRPEntry 3 } fsPimStdRPState OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The state of the RP." ::= { fsPimStdRPEntry 4 } fsPimStdRPStateTimer OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The minimum time remaining before the next state change. When pimRPState is up, this is the minimum time which must expire until it can be declared down. When pimRPState is down, this is the time until it will be declared up (in order to retry)." ::= { fsPimStdRPEntry 5 } fsPimStdRPLastChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The value of sysUpTime at the time when the corresponding instance of pimRPState last changed its value." ::= { fsPimStdRPEntry 6 } fsPimStdRPRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The status of this row, by which new entries may be created, or old entries deleted from this table." ::= { fsPimStdRPEntry 7 } -- The PIM RP-Set Table fsPimStdRPSetTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPimStdRPSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing PIM information for candidate Rendezvous Points (RPs) for IP multicast groups. When the local router is the BSR, this information is obtained from received Candidate-RP-Advertisements. When the local router is not the BSR, this information is obtained from received RP-Set messages." ::= { fsPimStdTables 6 } fsPimStdRPSetEntry OBJECT-TYPE SYNTAX FsPimStdRPSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimRPSetTable." INDEX { fsPimStdRPSetComponent, fsPimStdRPSetAddrType, fsPimStdRPSetGroupAddress, fsPimStdRPSetGroupMaskLen, fsPimStdRPSetAddress } ::= { fsPimStdRPSetTable 1 } FsPimStdRPSetEntry ::= SEQUENCE { fsPimStdRPSetAddrType InetAddressType, fsPimStdRPSetGroupAddress InetAddress, fsPimStdRPSetGroupMaskLen Integer32, fsPimStdRPSetAddress InetAddress, fsPimStdRPSetHoldTime Integer32, fsPimStdRPSetExpiryTime TimeTicks, fsPimStdRPSetComponent Integer32, fsPimStdRPSetPimMode INTEGER } fsPimStdRPSetAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address type in which the RP address belongs to." ::= { fsPimStdRPSetEntry 1 } fsPimStdRPSetGroupAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP multicast group address which, when combined with pimRPSetGroupMask, gives the group prefix for which this entry contains information about the Candidate-RP." ::= { fsPimStdRPSetEntry 2 } fsPimStdRPSetGroupMaskLen OBJECT-TYPE SYNTAX Integer32 (0..128) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The multicast group address mask which, when combined with pimRPSetGroupAddress, gives the group prefix for which this entry contains information about the Candidate-RP." ::= { fsPimStdRPSetEntry 3 } fsPimStdRPSetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of the Candidate-RP." ::= { fsPimStdRPSetEntry 4 } fsPimStdRPSetHoldTime OBJECT-TYPE SYNTAX Integer32 (0..255) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The holdtime of a Candidate-RP. If the local router is not the BSR, this value is 0." ::= { fsPimStdRPSetEntry 5 } fsPimStdRPSetExpiryTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum time remaining before the Candidate-RP will be declared down. If the local router is not the BSR, this value is 0." ::= { fsPimStdRPSetEntry 6 } fsPimStdRPSetComponent OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION " A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value." ::= { fsPimStdRPSetEntry 7 } fsPimStdRPSetPimMode OBJECT-TYPE SYNTAX INTEGER { dm (1), sm (2), ssm (3), bidir (4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value shows the PIM mode in the RP set entry" ::= { fsPimStdRPSetEntry 11 } -- -- Note: { pim 8 } through { pim 10 } were used in older versions -- of this MIB. Since some earlier versions of this MIB have been -- widely-deployed, these values must not be used in the future, -- as long the MIB is rooted under { experimental 61 }. -- -- The PIM Candidate-RP Table fsPimStdCandidateRPTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPimStdCandidateRPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the IP multicast groups for which the local router is to advertise itself as a Candidate-RP when the value of pimComponentCRPHoldTime is non-zero. If this table is empty, then the local router will advertise itself as a Candidate-RP for all groups (providing the value of pimComponentCRPHoldTime is non- zero)." ::= { fsPimStdTables 7 } fsPimStdCandidateRPEntry OBJECT-TYPE SYNTAX FsPimStdCandidateRPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimCandidateRPTable." INDEX { fsPimStdCandidateRPAddrType, fsPimStdCandidateRPGroupAddress, fsPimStdCandidateRPGroupMaskLen } ::= { fsPimStdCandidateRPTable 1 } FsPimStdCandidateRPEntry ::= SEQUENCE { fsPimStdCandidateRPAddrType InetAddressType, fsPimStdCandidateRPGroupAddress InetAddress, fsPimStdCandidateRPGroupMaskLen Integer32, fsPimStdCandidateRPAddress InetAddress, fsPimStdCandidateRPRowStatus RowStatus } fsPimStdCandidateRPAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP Address type in which the multicast group address, and RP address belong to." ::= { fsPimStdCandidateRPEntry 1 } fsPimStdCandidateRPGroupAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP multicast group address which, when combined with pimCandidateRPGroupMask, identifies a group prefix for which the local router will advertise itself as a Candidate-RP." ::= { fsPimStdCandidateRPEntry 2 } fsPimStdCandidateRPGroupMaskLen OBJECT-TYPE SYNTAX Integer32 (0..128) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The multicast group address mask which, when combined with pimCandidateRPGroupMask, identifies a group prefix for which the local router will advertise itself as a Candidate-RP." ::= { fsPimStdCandidateRPEntry 3 } fsPimStdCandidateRPAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The (unicast) address of the interface which will be advertised as a Candidate-RP." ::= { fsPimStdCandidateRPEntry 4 } fsPimStdCandidateRPRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row, by which new entries may be created, or old entries deleted from this table." ::= { fsPimStdCandidateRPEntry 5 } -- The PIM Component Table fsPimStdComponentTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPimStdComponentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing objects specific to a PIM domain. One row exists for each domain to which the router is connected. A PIM-SM domain is defined as an area of the network over which Bootstrap messages are forwarded. Typically, a PIM-SM router will be a member of exactly one domain. This table also supports, however, routers which may form a border between two PIM-SM domains and do not forward Bootstrap messages between them." ::= { fsPimStdTables 8 } fsPimStdComponentEntry OBJECT-TYPE SYNTAX FsPimStdComponentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimComponentTable." INDEX { fsPimStdComponentIndex } ::= { fsPimStdComponentTable 1 } FsPimStdComponentEntry ::= SEQUENCE { fsPimStdComponentIndex Integer32, fsPimStdComponentBSRExpiryTime TimeTicks, fsPimStdComponentCRPHoldTime Integer32, fsPimStdComponentStatus RowStatus, fsPimStdComponentScopeZoneName DisplayString } fsPimStdComponentIndex OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value. Routers that only support membership in a single PIM-SM domain should use a pimComponentIndex value of 1." ::= { fsPimStdComponentEntry 1 } fsPimStdComponentBSRExpiryTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum time remaining before the bootstrap router in the local domain will be declared down. For candidate BSRs, this is the time until the component sends an RP-Set message. For other routers, this is the time until it may accept an RP-Set message from a lower candidate BSR." ::= { fsPimStdComponentEntry 2 } fsPimStdComponentCRPHoldTime OBJECT-TYPE SYNTAX Integer32 (0..255) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The holdtime of the component when it is a candidate RP in the local domain. The value of 0 is used to indicate that the local system is not a Candidate-RP." DEFVAL { 0 } ::= { fsPimStdComponentEntry 3 } fsPimStdComponentStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this entry. Creating the entry creates another protocol instance; destroying the entry disables a protocol instance." ::= { fsPimStdComponentEntry 4 } fsPimStdComponentScopeZoneName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION " This object indicates the scope-zone associated with a particular component" ::= { fsPimStdComponentEntry 5 } fsPimStdComponentBSRTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPimStdComponentBSREntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing objects specific to a PIM domain. One row exists for each domain to which the router is connected. A PIM-SM domain is defined as an area of the network over which Bootstrap messages are forwarded. Typically, a PIM-SM router will be a member of exactly one domain. This table also supports, however, routers which may form a border between two PIM-SM domains and do not forward Bootstrap messages between them." ::= { fsPimStdTables 9 } fsPimStdComponentBSREntry OBJECT-TYPE SYNTAX FsPimStdComponentBSREntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimComponentTable." INDEX { fsPimStdComponentBSRIndex, fsPimStdComponentBSRAddrType} ::= { fsPimStdComponentBSRTable 1 } FsPimStdComponentBSREntry ::= SEQUENCE { fsPimStdComponentBSRIndex Integer32, fsPimStdComponentBSRAddrType InetAddressType, fsPimStdComponentBSRAddress InetAddress } fsPimStdComponentBSRIndex OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number uniquely identifying the component." ::= { fsPimStdComponentBSREntry 1 } fsPimStdComponentBSRAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address type of the bootstrap router (BSR) for the local PIM region." ::= { fsPimStdComponentBSREntry 2 } fsPimStdComponentBSRAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the bootstrap router (BSR) for the local PIM region." ::= { fsPimStdComponentBSREntry 3 } -- -- The PIM Neighbor Secondary Address Table -- fsPimStdNbrSecAddressTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPimStdNbrSecAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the secondary addresses advertised by each PIM neighbor (on a subset of the rows of the pimNeighborTable defined above)." REFERENCE "RFC 4601 section 4.3.4" ::= { fsPimStdTables 10 } fsPimStdNbrSecAddressEntry OBJECT-TYPE SYNTAX FsPimStdNbrSecAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the fsPimStdNbrSecAddressTable." INDEX { fsPimStdNbrSecAddressIfIndex, fsPimStdNbrSecAddressType, fsPimStdNbrSecAddressPrimary, fsPimStdNbrSecAddress } ::= { fsPimStdNbrSecAddressTable 1 } FsPimStdNbrSecAddressEntry ::= SEQUENCE { fsPimStdNbrSecAddressIfIndex InterfaceIndex, fsPimStdNbrSecAddressType InetAddressType, fsPimStdNbrSecAddressPrimary InetAddress, fsPimStdNbrSecAddress InetAddress } fsPimStdNbrSecAddressIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of ifIndex for the interface used to reach this PIM neighbor." ::= { fsPimStdNbrSecAddressEntry 1 } fsPimStdNbrSecAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address type of this PIM neighbor." ::= { fsPimStdNbrSecAddressEntry 2 } fsPimStdNbrSecAddressPrimary OBJECT-TYPE SYNTAX InetAddress (SIZE (4|8|16|20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The primary IP address of this PIM neighbor. The InetAddressType is given by the fsPimStdNbrSecAddressType object." ::= { fsPimStdNbrSecAddressEntry 3 } fsPimStdNbrSecAddress OBJECT-TYPE SYNTAX InetAddress (SIZE (4|8|16|20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The secondary IP address of this PIM neighbor. The InetAddressType is given by the fsPimStdNbrSecAddressType object." ::= { fsPimStdNbrSecAddressEntry 4 } END