-- Copyright (C) 2006-2012 Aricent. All Rights Reserved -- $Id: fspbrst.mib,v 1.7 2016/02/18 09:47:31 siva Exp $ ARICENT-PB-RSTP-MIB DEFINITIONS ::= BEGIN -- ------------------------------------------------------------------ -- Proprietary MIB for C-VLAN component Rapid Spanning Tree Protocol -- in Provider Bridges -- ------------------------------------------------------------------ IMPORTS OBJECT-TYPE, MODULE-IDENTITY, Integer32,Counter32, TimeTicks,enterprises FROM SNMPv2-SMI TEXTUAL-CONVENTION, TruthValue FROM SNMPv2-TC Timeout,BridgeId FROM BRIDGE-MIB; futurePbRstMIB MODULE-IDENTITY LAST-UPDATED "201209050000Z" ORGANIZATION "ARICENT COMMUNICATIONS SOFTWARE" CONTACT-INFO "support@aricent.com" DESCRIPTION "MIB for Rapid Spanning Tree Algorithm & Protocol in C-VLAN component of Provider Bridges" REVISION "201209050000Z" DESCRIPTION "MIB for Rapid Spanning Tree Algorithm & Protocol in C-VLAN component of Provider Bridges" ::= { enterprises futuresoftware(2076) 123 } EnabledStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A simple status value for the object." SYNTAX INTEGER { enabled(1), disabled(2) } VlanId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This value and the CEP port identifier are indices to C-VLAN port tables. Values 1 to 4095 are permitted. Values from 1 to 4094 represents S-VLAN id. (CEP, 4095) identifies the CEP port in the C-VLAN component." SYNTAX Integer32 (1..4095) futurePbRst OBJECT IDENTIFIER ::= { futurePbRstMIB 1 } -- Provider Bridges C-VLAN component RSTP Port Extention Group fsPbProviderStpStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the administrative module status requested by management for the spanning tree operation in S-VLAN component of Provider Bridges. This enables or disables spanning tree protocol (RSTP/MSTP)on S-VLAN component ports. A value of 'enabled' (1) indicates that the spanning tree protocol will be enabled on all the ports of the S-VLAN component. A value of 'disabled'(2) indicates that the spanning tree protocol will be disabled on all the ports of the S-VLAN component. This object can be set only after the object fsRstSystemControl has been set." ::= {futurePbRst 1} fsPbRstCVlanBridgeTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbRstCVlanBridgeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains bridge related information for RSTP operation in the C-VLAN component." ::= { futurePbRst 2 } fsPbRstCVlanBridgeEntry OBJECT-TYPE SYNTAX FsPbRstCVlanBridgeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table is for each C-VLAN component in Provider Bridges." INDEX { fsPbRstPort } ::= { fsPbRstCVlanBridgeTable 1 } FsPbRstCVlanBridgeEntry ::= SEQUENCE { fsPbRstPort Integer32, fsPbRstCVlanBridgeId BridgeId, fsPbRstCVlanBridgeDesignatedRoot BridgeId, fsPbRstCVlanBridgeRootCost Integer32, fsPbRstCVlanBridgeMaxAge Timeout, fsPbRstCVlanBridgeHelloTime Timeout, fsPbRstCVlanBridgeHoldTime Integer32, fsPbRstCVlanBridgeForwardDelay Timeout, fsPbRstCVlanBridgeTxHoldCount Integer32, fsPbRstCVlanStpHelloTime Timeout, fsPbRstCVlanStpMaxAge Timeout, fsPbRstCVlanStpForwardDelay Timeout, fsPbRstCVlanStpTopChanges Counter32, fsPbRstCVlanStpTimeSinceTopologyChange TimeTicks } fsPbRstPort OBJECT-TYPE SYNTAX Integer32(0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object always indicates the port which is of type CEP. CEP port will be the index of the CVLAN Spanning tree." ::= { fsPbRstCVlanBridgeEntry 1} fsPbRstCVlanBridgeId OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The Bridge-Identifier as used in the Spanning Tree Protocol operation in the C-VLAN component to uniquely identify a bridge. Bridge Mac address field in this object will be the MAC address of the corresponding customer edge port. The Bridge priority field in this object will be always 0xf. The Bridge Identifier System Id extension field in this object will be always 0xfff." ::= { fsPbRstCVlanBridgeEntry 2 } fsPbRstCVlanBridgeDesignatedRoot OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this C-VLAN component. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this C-VLAN component." ::= { fsPbRstCVlanBridgeEntry 3 } fsPbRstCVlanBridgeRootCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The cost of the path to the root as seen from this C-VLAN component bridge." ::= { fsPbRstCVlanBridgeEntry 4 } fsPbRstCVlanBridgeMaxAge OBJECT-TYPE SYNTAX Timeout MAX-ACCESS read-only STATUS current DESCRIPTION "The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds." ::= { fsPbRstCVlanBridgeEntry 5 } fsPbRstCVlanBridgeHelloTime OBJECT-TYPE SYNTAX Timeout MAX-ACCESS read-only STATUS current DESCRIPTION "The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds." ::= { fsPbRstCVlanBridgeEntry 6 } fsPbRstCVlanBridgeHoldTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this C-VLAN component, in units of hundredths of a second." ::= { fsPbRstCVlanBridgeEntry 7 } fsPbRstCVlanBridgeForwardDelay OBJECT-TYPE SYNTAX Timeout MAX-ACCESS read-only STATUS current DESCRIPTION "The value that all bridges use for Forward Delay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds." ::= { fsPbRstCVlanBridgeEntry 8 } fsPbRstCVlanBridgeTxHoldCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value used by the Port Transmit state machine to limit the maximum transmission rate." ::= { fsPbRstCVlanBridgeEntry 9 } fsPbRstCVlanStpHelloTime OBJECT-TYPE SYNTAX Timeout MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time between the transmission of Configuration bridge PDUs by this C-VLAN component on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using." ::= { fsPbRstCVlanBridgeEntry 10 } fsPbRstCVlanStpMaxAge OBJECT-TYPE SYNTAX Timeout MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using." ::= { fsPbRstCVlanBridgeEntry 11 } fsPbRstCVlanStpForwardDelay OBJECT-TYPE SYNTAX Timeout MAX-ACCESS read-only STATUS current DESCRIPTION "This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]" ::= { fsPbRstCVlanBridgeEntry 12 } fsPbRstCVlanStpTopChanges OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the total number of topology changes detected by this bridge since the management entity was last reset or initialized." ::= { fsPbRstCVlanBridgeEntry 13 } fsPbRstCVlanStpTimeSinceTopologyChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity." ::= { fsPbRstCVlanBridgeEntry 14 } fsPbRstCVlanPortInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbRstCVlanPortInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the objects for RSTP in C-VLAN component of Provider Bridges." ::= { futurePbRst 3 } fsPbRstCVlanPortInfoEntry OBJECT-TYPE SYNTAX FsPbRstCVlanPortInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table is for each C-VLAN component in Provider Bridges. Here the port represents the Ports (CEP/PEPs) of C-VLAN component. Each table entry gives the spanning tree information for the Customer Edge Port and Provider Edge Ports of C-VLAN components in Provider Bridges." INDEX { fsPbRstPort,fsPbRstCepSvid } ::= { fsPbRstCVlanPortInfoTable 1 } FsPbRstCVlanPortInfoEntry ::= SEQUENCE { fsPbRstCepSvid VlanId, fsPbRstCVlanPortPriority Integer32, fsPbRstCVlanPortPathCost Integer32, fsPbRstCVlanPortRole INTEGER, fsPbRstCVlanPortState INTEGER, fsPbRstCVlanPortAdminEdgePort TruthValue, fsPbRstCVlanPortOperEdgePort TruthValue, fsPbRstCVlanPortAdminPointToPoint INTEGER, fsPbRstCVlanPortOperPointToPoint TruthValue, fsPbRstCVlanPortAutoEdge TruthValue, fsPbRstCVlanPortDesignatedRoot BridgeId, fsPbRstCVlanPortDesignatedCost Integer32, fsPbRstCVlanPortDesignatedBridge BridgeId, fsPbRstCVlanPortDesignatedPort OCTET STRING, fsPbRstCVlanPortForwardTransitions Counter32 } fsPbRstCepSvid OBJECT-TYPE SYNTAX VlanId MAX-ACCESS not-accessible STATUS current DESCRIPTION "This value and the CEP port identifier are indices to C-VLAN port tables. Values 1 to 4095 are permitted. Values from 1 to 4094 represents S-VLAN id. (CEP, 4095) identifies the CEP port in the C-VLAN component." ::= {fsPbRstCVlanPortInfoEntry 1} fsPbRstCVlanPortPriority OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of fsPbRstPort. Priority is always assumed as 32 for C-VLAN component Ports." REFERENCE "IEEE 802.1D-1990: Section 4.5.5.1" ::= { fsPbRstCVlanPortInfoEntry 2 } fsPbRstCVlanPortPathCost OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN. Pathcost is always assumed as 128 for Provider Edge Ports. For CEP, port-path cost will be taken from dot1dStpPortPathCost of fsPbRstPort." REFERENCE "IEEE 802.1D-1990: Section 4.5.5.3" ::= { fsPbRstCVlanPortInfoEntry 3 } fsPbRstCVlanPortRole OBJECT-TYPE SYNTAX INTEGER { disabledPort(0), alternatePort(1), backupPort(2), rootPort(3), designatedPort(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the current Port Role assumed by this Port." ::= { fsPbRstCVlanPortInfoEntry 4 } fsPbRstCVlanPortState OBJECT-TYPE SYNTAX INTEGER { disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpPortEnable), this object will have a value of disabled(1)." REFERENCE "IEEE 802.1D-1990: Section 4.5.5.2" ::= { fsPbRstCVlanPortInfoEntry 5 } fsPbRstCVlanPortAdminEdgePort OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the administrative value of the Edge Port parameter. A value of TRUE(1) indicates that this port should be assumed as an edge-port and a value of FALSE(2) indicates that this port should be assumed as a non-edge-port. This is always 'false' for a Provider Egde Port." REFERENCE "IEEE 802.1t clause 14.8.2, 18.3.3" ::= { fsPbRstCVlanPortInfoEntry 6 } fsPbRstCVlanPortOperEdgePort OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the operational value of the Edge Port parameter. This object always assumes the value of 'False' for Provider Edge Ports of C-VLAN component." REFERENCE "IEEE 802.1t clause 14.8.2, 18.3.4" ::= { fsPbRstCVlanPortInfoEntry 7 } fsPbRstCVlanPortAdminPointToPoint OBJECT-TYPE SYNTAX INTEGER { forceTrue(0), forceFalse(1), auto(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means. Provider Edge Ports always assume the value of 'auto' for this object." REFERENCE "IEEE 802.1w clause 6.4.3, 6.5, 14.8.2" ::= { fsPbRstCVlanPortInfoEntry 8 } fsPbRstCVlanPortOperPointToPoint OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. This object will be set to 'True' for Provider Edge Ports when the S-VLAN is attached to only two customer interfaces. This will be set to 'False' when the S-VLAN is attached to more than two customer interfaces." REFERENCE "IEEE 802.1w clause 6.4.3, 6.5, 14.8.2" ::= { fsPbRstCVlanPortInfoEntry 9 } fsPbRstCVlanPortAutoEdge OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter when TRUE(1) indicates that detection of a port as Edge Port happens automatically and FALSE(2) indicates that this feature is disabled. This object is always set to 'True' for Provider Edge Ports of C-VLAN component." ::= { fsPbRstCVlanPortInfoEntry 10 } fsPbRstCVlanPortDesignatedRoot OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which this port is attached." REFERENCE "IEEE 802.1D-1990: Section 4.5.5.4" ::= { fsPbRstCVlanPortInfoEntry 11 } fsPbRstCVlanPortDesignatedCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs." REFERENCE "IEEE 802.1D-1990: Section 4.5.5.5" ::= { fsPbRstCVlanPortInfoEntry 12 } fsPbRstCVlanPortDesignatedBridge OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment." REFERENCE "IEEE 802.1D-1990: Section 4.5.5.6" ::= { fsPbRstCVlanPortInfoEntry 13 } fsPbRstCVlanPortDesignatedPort OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Port Identifier of the port on the Designated Bridge for this port's segment." REFERENCE "IEEE 802.1D-1990: Section 4.5.5.7" ::= { fsPbRstCVlanPortInfoEntry 14 } fsPbRstCVlanPortForwardTransitions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this port has transitioned from the Learning state to the Forwarding state." ::= { fsPbRstCVlanPortInfoEntry 15 } fsPbRstCVlanPortSmTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbRstCVlanPortSmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the objects for the state machine information of C-VLAN component Ports Provider Edge Bridges." ::= { futurePbRst 4 } fsPbRstCVlanPortSmEntry OBJECT-TYPE SYNTAX FsPbRstCVlanPortSmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table is for each C-VLAN component in Provider Bridges. Here the port represents the C-VLAN component ports. Each table entry gives the state machine information for a C-VLAN component Port in Provider Edge Bridges." INDEX { fsPbRstPort,fsPbRstCepSvid } ::= { fsPbRstCVlanPortSmTable 1 } FsPbRstCVlanPortSmEntry ::= SEQUENCE { fsPbRstCVlanPortInfoSmState INTEGER, fsPbRstCVlanPortMigSmState INTEGER, fsPbRstCVlanPortRoleTransSmState INTEGER, fsPbRstCVlanPortStateTransSmState INTEGER, fsPbRstCVlanPortTopoChSmState INTEGER, fsPbRstCVlanPortTxSmState INTEGER } fsPbRstCVlanPortInfoSmState OBJECT-TYPE SYNTAX INTEGER { disabled (0), aged (1), update (2), superior (3), repeat (4), notdesignated (5), present (6), receive (7), inferiordesignated (8) } MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the current state of the Port Information state machine. This object will hold the value 'disabled' when the Port Information state machine is in the DISABLED state, the value 'aged' when the state machine is in the AGED state, the value 'update' when the state machine is in the UPDATE state, the value 'superior' when the state machine is in the SUPERIOR state, the value 'repeat' when the state machine is in the REPEAT state, the value 'notdesignated' when the state machine is in the NOT_DESIGNATED state, the value 'present' when the state machine is in the CURRENT state and the value 'receive' when the state machine is in the RECEIVE state and the value 'inferiordesignated' when the state machine is in the INFERIOR_DESIGNATED state." ::= { fsPbRstCVlanPortSmEntry 1 } fsPbRstCVlanPortMigSmState OBJECT-TYPE SYNTAX INTEGER { checkingrstp (0), selectingstp (1), sensing (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the current state of the Port Protocol Migration state machine. This object will hold the value 'checkingrstp' when the Protocol Migration state machine is in the CHECKING_RSTP state, the value 'selectingstp' when the state machine is in the SELECTING_STP state, the value 'sensing' when the state machine is in the SENSING state." ::= { fsPbRstCVlanPortSmEntry 2 } fsPbRstCVlanPortRoleTransSmState OBJECT-TYPE SYNTAX INTEGER { init (0), disableport (1), disabledport (2), rootport (3), designatedport (4), backupport (5), rootproposed (6), rootagreed(7), reroot (8), rootforward (9), rootlearn (10), rerooted (11), designatedpropose (12), designatedsynced (13), designatedretired (14), designatedforward (15), designatedlearn (16), designatedlisten (17) } MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the current state of the Port Role Transition state machine. This object will hold the value 'init' when the Port Role Transition state machine is in the INIT state, the value 'disableport' when the state machine is in the DISABLE_PORT state, the value 'disabledport' when the state machine is in the DISABLED_PORT state, the value 'rootport' when the state machine is in the ROOT_PORT state, the value 'desgport' when the state machine is in the DESIGNATED_PORT state, the value 'backupport' when the state machine is in BACKUP_PORT state, the value 'rootproposed' when the state machine is in the ROOT_PROPOSED state, the value 'rootagreed' when the state machine is in the ROOT_AGREED state, the value 'reroot' when the state machine is in the REROOT state, the value 'rootforward' when the state machine is in the ROOT_FORWARD state, the value 'rootlearn' when the state machine is in the ROOT_LEARN state, the value 'rerooted' when the state machine is in the REROOTED state, the value 'designatedpropose' when the state machine is in the DESIGNATED_PROPOSE state, the value 'designatedsynced' when the state machine is in the DESIGNATED_SYNCED state, the value 'designatedretired' when the state machine is in the DESIGNATED_RETIRED state, the value 'designatedforward' when the state machine is in the DESIGNATED_FORWARD state, the value 'designatedlearn' when the state machine is in the DESIGNATED_LEARN state and the value 'designatedlisten' when the state machine is in the DESIGNATED_LISTEN state." ::= { fsPbRstCVlanPortSmEntry 3 } fsPbRstCVlanPortStateTransSmState OBJECT-TYPE SYNTAX INTEGER { discarding (0), learning (1), forwarding (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the current state of the Port State Transition state machine. This object is used to hold the value 'discarding' when the Port State Transition state machine is in the DISCARDING state, the value 'learning' when the state machine is in the LEARNING state and the value 'forwarding' when the state machine is in the FORWARDING state." ::= { fsPbRstCVlanPortSmEntry 4 } fsPbRstCVlanPortTopoChSmState OBJECT-TYPE SYNTAX INTEGER { inactive (0), learning (1), detected (2), active (3), notifiedtcn (4), notifiedtc (5), propagating (6), acknowledged (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the current state of the Topology Change state machine. This object is used to hold the value 'inactive' when the Topology Change state machine is in the INACTIVE state, the value 'learning' when the state machine is in the LEARNING state, the value 'active' when the state machine is in the ACTIVE state, the value 'detected' when the state machine is in the DETECTED state, the value 'notifiedtcn' when the state machine is in the NOTIFIED_TCN state, the value 'notifiedtc' when the state machine is in the NOTIFIED_TC state, the value 'propagating' state when the state machine is in the PROPAGATING state and the value 'acknowledged' when the state machine is in the ACKNOWLEDGED state." ::= { fsPbRstCVlanPortSmEntry 5 } fsPbRstCVlanPortTxSmState OBJECT-TYPE SYNTAX INTEGER { transmitinit (0), transmitperiodic (1), transmitconfig (2), transmittcn (3), transmitrstp (4), idle (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the current state of the Port Transmit state machine. This object is used to hold the value 'transmitinit' when the Port Transmit state machine is in the TRANSMIT_INIT state, the value 'transmitperiodic' when the state machine is in the TRANSMIT_PERIODIC state, the value 'transmitconfig' when the state machine is in the TRANSMIT_CONFIG state, the value 'transmittcn', when the state machine is in the TRANSMIT_TCN state, the value 'transmitrstp', when the state machine is in the TRANSMIT_RSTP state and the value 'idle' when the state machine is in the IDLE state." ::= { fsPbRstCVlanPortSmEntry 6 } fsPbRstCVlanPortStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF FsPbRstCVlanPortStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the spanning tree statistics information for the C-VLAN component ports." ::= { futurePbRst 5 } fsPbRstCVlanPortStatsEntry OBJECT-TYPE SYNTAX FsPbRstCVlanPortStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table is for each C-VLAN component in Provider Bridges. Here the port represents the C-VLAN component ports. Each table entry gives the spanning tree protocol statistics information for the C-VLAN component ports." INDEX { fsPbRstPort,fsPbRstCepSvid } ::= { fsPbRstCVlanPortStatsTable 1 } FsPbRstCVlanPortStatsEntry ::= SEQUENCE { fsPbRstCVlanPortRxRstBpduCount Counter32, fsPbRstCVlanPortRxConfigBpduCount Counter32, fsPbRstCVlanPortRxTcnBpduCount Counter32, fsPbRstCVlanPortTxRstBpduCount Counter32, fsPbRstCVlanPortTxConfigBpduCount Counter32, fsPbRstCVlanPortTxTcnBpduCount Counter32, fsPbRstCVlanPortInvalidRstBpduRxCount Counter32, fsPbRstCVlanPortInvalidConfigBpduRxCount Counter32, fsPbRstCVlanPortInvalidTcnBpduRxCount Counter32, fsPbRstCVlanPortProtocolMigrationCount Counter32, fsPbRstCVlanPortEffectivePortState TruthValue } fsPbRstCVlanPortRxRstBpduCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RST BPDUs that have been received on this Port." ::= { fsPbRstCVlanPortStatsEntry 1 } fsPbRstCVlanPortRxConfigBpduCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Config BPDUs that have been received on this Port." ::= { fsPbRstCVlanPortStatsEntry 2 } fsPbRstCVlanPortRxTcnBpduCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of TCN BPDUs that have been received on this Port." ::= { fsPbRstCVlanPortStatsEntry 3 } fsPbRstCVlanPortTxRstBpduCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RST BPDUs that have been transmitted by this Port." ::= { fsPbRstCVlanPortStatsEntry 4 } fsPbRstCVlanPortTxConfigBpduCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Config BPDUs that have been transmitted by this Port." ::= { fsPbRstCVlanPortStatsEntry 5 } fsPbRstCVlanPortTxTcnBpduCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of TCN BPDUs that have been transmitted by this Port." ::= { fsPbRstCVlanPortStatsEntry 6 } fsPbRstCVlanPortInvalidRstBpduRxCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of invalid RSTP BPDUs that have been received on this Port." ::= { fsPbRstCVlanPortStatsEntry 7 } fsPbRstCVlanPortInvalidConfigBpduRxCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of invalid Configuration BPDUs that have been received on this Port." ::= { fsPbRstCVlanPortStatsEntry 8 } fsPbRstCVlanPortInvalidTcnBpduRxCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of invalid TCN BPDUs that have been received on this Port." ::= { fsPbRstCVlanPortStatsEntry 9 } fsPbRstCVlanPortProtocolMigrationCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the protocol has been migrated from RSTP to STP and vice versa in CVLAN component." ::= { fsPbRstCVlanPortStatsEntry 10 } fsPbRstCVlanPortEffectivePortState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The effective Operational state of this port. This object will be set to TRUE only when the port is operationally up in the interface manager and the force Port State for this port and specified port state is enabled. Otherwise, this object is set to FALSE." ::= { fsPbRstCVlanPortStatsEntry 11 } END