-- Copyright (C) 2018 Aricent Group . All Rights Reserved. --$Id: fslbd.mib,v 1.1 2018/06/18 04:36:16 vijay Exp $ -- This is the MIB for Aricent proprietary "Loop Back Detection" feature ARICENT-LBD-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE, MODULE-IDENTITY, Integer32, Counter32, enterprises FROM SNMPv2-SMI TruthValue,RowStatus, MacAddress FROM SNMPv2-TC ifIndex FROM IF-MIB; futureLbdMIB MODULE-IDENTITY LAST-UPDATED "201805300000Z" ORGANIZATION "ARICENT COMMUNICATIONS SOFTWARE" CONTACT-INFO "support@aricent.com" DESCRIPTION " This proprietary MIB module for loopback detection feature." ::= { enterprises aricent-communication-holding-ltd(29601) iss(2) 123} -- *************************************************************************** -- Groups in the MIB -- *************************************************************************** fsLbdSystems OBJECT IDENTIFIER ::= { futureLbdMIB 1 } fsLbdConfig OBJECT IDENTIFIER ::= { futureLbdMIB 2 } -- SCALAR BEGIN fsLbdSystemControl OBJECT-TYPE SYNTAX INTEGER { start(1), shutdown(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative system control status of Loopback Detection feature. The value 'start' (1) indicates that all resources required by the module should be allocated. The value 'shutdown' (2) indicates that Loopback Detection feature is shutdown in the device and all allocated memory should be released." DEFVAL { start } ::= { fsLbdSystems 1} fsLbdModuleStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative module status of Loopback Detection feature. This enables or disables Loopback Detection in the system . A value of 'enabled' (1) indicates that Loopback Detection is enabled in the device. A value of 'disabled' (2) indicates that Loopback Detection is disabled in the device." DEFVAL { disabled } ::= { fsLbdSystems 2} fsLbdTransmitInterval OBJECT-TYPE SYNTAX INTEGER (1..60) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the time interval(in seconds) between two consecutive Loop Back Detection (LBD) PDUs" DEFVAL { 30 } ::= { fsLbdSystems 3} fsLbdDestMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the destination MAC address of the Loop Back Detection PDUS. By default broadcast address is used as destination MAC address in the LBD PDUs. User can configure a preferred, unreserved multicast MAC address (01:xx:xx:xx:xx:xx) as destination MAC address for the LBD PDUs." ::= { fsLbdSystems 4 } fsLbdTraceOption OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to enable trace statements in Loopback detection module. The mapping between the bit positions & the level of trace is as follows: 1 - Control Plane Traces 2 - Packet Flow Traces 3 - Critical Traces 4 - Packet Dump Traces 5 - Buffer Trace " DEFVAL { 8 } ::= { fsLbdSystems 5 } -- SCALAR END -- -------------------------------------------- -- Loopback-detection Table -- -------------------------------------------- fsLbdPortTable OBJECT-TYPE SYNTAX SEQUENCE OF FsLbdPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Loop Back Detection related configuration and statistics at port level." ::= {fsLbdConfig 1} fsLbdPortEntry OBJECT-TYPE SYNTAX FsLbdPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Each entry in this table contains Loop Back Detection related configuration and statistics for a port." INDEX { fsLbdPortId } ::= {fsLbdPortTable 1} FsLbdPortEntry ::= SEQUENCE { fsLbdPortId Integer32, fsLbdLoopDetectStatus INTEGER, fsLbdTxCount Counter32, fsLbdRxCount Counter32, fsLbdPortStatus INTEGER, fsLbdPktTxFromPort Integer32, fsLbdPortRowStatus RowStatus, fsLbdClearStats TruthValue } fsLbdPortId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION " This object specifies the Inteface index over which Loopback detection is connected" ::= {fsLbdPortEntry 1} fsLbdLoopDetectStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to enable or disable the Loopback detection functionality in the port. A value of 'enabled' (1) indicates that Loopback detection functionality is enabled on the port. A value of 'disabled' (2) indicates that Loopback detection functionality is disabled in the port. Loop Back Detection on a port will function only when the feature is enabled in the system as well as on the port." DEFVAL { enabled } ::= {fsLbdPortEntry 2} fsLbdTxCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the number of LPD PDUs transmitted out of the port." ::= {fsLbdPortEntry 3} fsLbdRxCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the number of LPD PDUs received on the port." ::= {fsLbdPortEntry 4} fsLbdPortStatus OBJECT-TYPE SYNTAX INTEGER { noloopback(0), loopback(1)} MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current condition of the network connected to the port. 'noloopback' indicates that loop back condition is not detected in the network connected to the port. 'loopback' indicates that loop back condition is detected in the network connected to the port." ::= {fsLbdPortEntry 5} fsLbdPktTxFromPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the 'port-number' that was present in the received LBD PDU. This port-number may be the potential port causing the loop condition in the network. This object is valid only when 'loopback' condition is detected on a port." ::= {fsLbdPortEntry 6} fsLbdPortRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Row status for the Port Entry" ::= {fsLbdPortEntry 7} fsLbdClearStats OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to clear the statistics of port. When this object is set to 'true', it will clear the statistics of the port and reverts back to 'false'" DEFVAL { false } ::= {fsLbdPortEntry 8} END