QTECH-VPLS-LDP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, transmission FROM SNMPv2-SMI -- RFC2578 MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF -- RFC2580 TruthValue,RowStatus FROM SNMPv2-TC -- RFC2579 IANAPwTypeTC, IANAPwPsnTypeTC, IANAPwCapabilities FROM IANA-PWE3-MIB -- [RFC5601] InetAddressType, InetAddress FROM INET-ADDRESS-MIB -- [RFC4001] qtechvplsConfigIndex, qtechvplsPwBindIndex FROM QTECH-VPLS-GENERIC-MIB qtechMgmt FROM QTECH-SMI ; qtechvplsLdpDraft01MIB MODULE-IDENTITY LAST-UPDATED "201004281200Z" -- 28 April 2010 12:00:00 GMT ORGANIZATION "Qtech Networks Co.,Ltd." CONTACT-INFO " Tel: 4008-111-000 E-mail: service@qtech.com.cn" DESCRIPTION "Copyright (C) Qtech NETWORKS. This MIB module contains managed object definitions for LDP signalled Virtual Private LAN Services as in [RFC4762] This MIB module enables the use of any underlying PseudoWire network. " -- Revision history. REVISION "201004281200Z" -- 28 April 2010 12:00:00 GMT DESCRIPTION "Initial version published as part of Qtech private MIB." ::= { qtechMgmt 78 } -- Top-level components of this MIB. -- Notifications qtechvplsLdpNotifications OBJECT IDENTIFIER ::= { qtechvplsLdpDraft01MIB 0 } -- Tables, Scalars qtechvplsLdpObjects OBJECT IDENTIFIER ::= { qtechvplsLdpDraft01MIB 1 } -- Conformance qtechvplsLdpConformance OBJECT IDENTIFIER ::= { qtechvplsLdpDraft01MIB 2 } qtechvplsLdpConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechVplsLdpConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies information for configuring and monitoring LDP specific parameters for Virtual Private Lan Services(VPLS)." ::= { qtechvplsLdpObjects 1 } qtechvplsLdpConfigEntry OBJECT-TYPE SYNTAX QtechVplsLdpConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table represents LDP specific information for Virtual Private Lan Service(VPLS) in a packet network. It is indexed by qtechvplsConfigIndex, which uniquely identifies a single VPLS. A row is automatically created when a VPLS service is configured using LDP signalling. None of the read-create objects values can be changed when vplsRowStatus is in the active(1) state. Changes are allowed when the qtechvplsRowStatus is in notInService(2) or notReady(3) states only. If the operator need to change one of the values for an active row the qtechvplsConfigRowStatus should be first changed to notInService(2), the objects may be changed now, and later to active(1) in order to re-initiate the signaling process with the new values in effect. " INDEX { qtechvplsConfigIndex,qtechvplsLdpPwIndex} ::= { qtechvplsLdpConfigTable 1 } QtechVplsLdpConfigEntry ::= SEQUENCE { qtechvplsLdpPwIndex Unsigned32, qtechvplsLdpPeerAddr InetAddress, qtechvplsLdpPwId Unsigned32, qtechvplsPwType INTEGER, qtechvplsPwEncapType IANAPwTypeTC, qtechvplsLdpNeighborRowStatus RowStatus } qtechvplsLdpPwIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index for pesudowire using LDp signal. This figures out one PW with one peer. " ::= { qtechvplsLdpConfigEntry 1 } qtechvplsLdpPeerAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This object contains the value of the peer node address of the PW/PE maintenance protocol entity. This object SHOULD contain a value of all zeroes if not applicable (pwPeerAddrType is 'unknown'). The value of this object must be specifed when the row is created and cannot be changed while the row status is active(1) " ::= { qtechvplsLdpConfigEntry 2 } qtechvplsLdpPwId OBJECT-TYPE SYNTAX Unsigned32 (1..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "Same as VC ID. Please refer to system configuration guide for more details." ::= { qtechvplsLdpConfigEntry 3 } qtechvplsPwType OBJECT-TYPE SYNTAX INTEGER { mesh (1), spoke (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object indicates whether the Pseudo Wire binding is of type mesh or spoke. The value of this object must be specified when the row is created and cannot be changed while the row status is active(1)" ::= { qtechvplsLdpConfigEntry 4 } qtechvplsPwEncapType OBJECT-TYPE SYNTAX IANAPwTypeTC MAX-ACCESS read-create STATUS current DESCRIPTION "This value indicates the emulated service to be carried over this PW. " ::= { qtechvplsLdpConfigEntry 5 } qtechvplsLdpNeighborRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table. When a row in this table is in active(1) state." ::= { qtechvplsLdpConfigEntry 6 } -- Compliance requirement for read-only implementations. qtechvplsLdpCompliances OBJECT IDENTIFIER ::= { qtechvplsLdpConformance 1 } qtechvplsLdpModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance requirement for implementations that provide full support for VPLS-LDP-DRAFT-01-MIB. Such devices can then be monitored and configured using this MIB module." MODULE -- this module MANDATORY-GROUPS { qtechvplsLdpGroup, qtechvplsLdpNotificationGroup } ::= { qtechvplsLdpCompliances 1 } qtechvplsLdpModuleReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance requirement for implementations that only provide read-only support for VPLS-LDP-DRAFT-01-MIB. Such devices can then be monitored but cannot be configured using this MIB modules." MODULE -- this module MANDATORY-GROUPS { qtechvplsLdpGroup, qtechvplsLdpNotificationGroup } OBJECT qtechvplsLdpConfigMacAddrWithdraw MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT qtechvplsLdpPwBindMacAddressLimit MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { qtechvplsLdpCompliances 2 } -- Units of conformance. qtechvplsLdpGroups OBJECT IDENTIFIER ::= { qtechvplsLdpConformance 2 } END