-- *****************************************************************
-- QTECH-RSTP-MIB.mib:  Qtech RSTP MIB file
--
-- March 2002, Wuzg
--
-- Copyright (c) 2002 by Qtech Networks Co.,Ltd.
-- All rights reserved.
-- 
-- *****************************************************************
--

QTECH-RSTP-MSTP-MIB DEFINITIONS ::= BEGIN

IMPORTS
        MODULE-IDENTITY,
        OBJECT-TYPE,
        TimeTicks,
        Integer32,
        Counter32
                FROM SNMPv2-SMI
        TruthValue,
        DisplayString
                FROM SNMPv2-TC
        MODULE-COMPLIANCE,
        OBJECT-GROUP
                FROM SNMPv2-CONF
        IfIndex,
        ConfigStatus
                FROM QTECH-TC 
        BridgeId 
                FROM BRIDGE-MIB
        EnabledStatus
                FROM P-BRIDGE-MIB
        qtechMgmt
                FROM QTECH-SMI;

qtechStpMIB MODULE-IDENTITY
        LAST-UPDATED "200203200000Z"
        ORGANIZATION "Qtech Networks Co.,Ltd."
        CONTACT-INFO
                " 
                Tel: 4008-111-000 

                E-mail: service@qtech.com.cn"
        DESCRIPTION
                "This module defines qtech stp mibs."
        REVISION      "200203200000Z"
        DESCRIPTION
                "Initial version of this MIB module."
        ::= { qtechMgmt 16}

qtechStpMIBObjects OBJECT IDENTIFIER ::=  { qtechStpMIB 1 }
qtechRstpMIBObjects OBJECT IDENTIFIER ::= { qtechStpMIB 2 }
qtechMstpMIBObjects OBJECT IDENTIFIER ::= { qtechStpMIB 3 }

-- -------------------------------------------------------------
-- extend of stp
-- -------------------------------------------------------------
qtechSysStpStatus OBJECT-TYPE
        SYNTAX EnabledStatus
        MAX-ACCESS read-write
        STATUS current
        DESCRIPTION
            "This object allow of enabling or disabling the Spanning
            Tree Protocol in the system, this will avoid the circle
            exist in the net environment, then avoid the broad cast
            storm. and when set its value to enable(1) will cause a
            short time that the station can not connect the agent,
            waitting for the topology become stable."
        DEFVAL { disabled }
        ::= { qtechStpMIBObjects 1 }
    
qtechSysStpReset OBJECT-TYPE
        SYNTAX Integer32
        MAX-ACCESS read-write
        STATUS current
        DESCRIPTION
            "This object allow of resetting all Spanning Tree Protocol
            parameter reset to default settings. set its value to any
            but 0, will cause agent reset the parameters, set it to 0
            will cause no action. this operation may cause some interval
            the station can not connect the agent depending on the
            parameters previous set."
        ::= { qtechStpMIBObjects 2 }

qtechStpExtPortTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF QtechStpExtPortEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "A table that contains port-specific Spanning Tree
         extend information."
    ::= { qtechStpMIBObjects 3 }

qtechStpExtPortEntry OBJECT-TYPE
    SYNTAX      QtechStpExtPortEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "A list of Spanning Tree extend information maintained by
         each port."
    INDEX    { qtechStpPortIfIndex }
    ::= { qtechStpExtPortTable 1 }

QtechStpExtPortEntry ::=
    SEQUENCE {
        qtechStpPortIfIndex
            IfIndex,
        qtechStpPortAdminPathCost
            INTEGER,
        qtechStpPortOperPathCost
            INTEGER,
        qtechStpPortRole
            INTEGER
--        qtechStpPortIfRunSTP
--            TruthValue    
    }
qtechStpPortIfIndex OBJECT-TYPE
        SYNTAX IfIndex
        MAX-ACCESS read-only
        STATUS current
        DESCRIPTION
            "include only physical port and trunk port "
        ::= { qtechStpExtPortEntry 1 }
            
qtechStpPortAdminPathCost OBJECT-TYPE
        SYNTAX  INTEGER (0..200000000)
        MAX-ACCESS  read-write
        STATUS  current
        DESCRIPTION
              "The contribution of this port to the path cost of
              paths towards the spanning tree root which include
              this port.  802.1D-1990 recommends that the
              default value of this parameter be in inverse
              proportion to the speed of the attached LAN.
              Setting this value to 0 indicates that port's real
              path cost will be automaticly assigned by system
              according to duplex and speed of the port.Setting 
              this value to other value and system will assigned this 
              value to the port."
        DEFVAL{0}
        ::= { qtechStpExtPortEntry  2 }

qtechStpPortOperPathCost OBJECT-TYPE
        SYNTAX  INTEGER (1..200000000)
        MAX-ACCESS  read-only
        STATUS  current
        DESCRIPTION
              " Actual oper value of port cost."
        ::= { qtechStpExtPortEntry  3 }

qtechStpPortRole OBJECT-TYPE
        SYNTAX  INTEGER {
               disabledPort(1),
               alternatePort(2),
               backupPort(3),
               rootPort(4),
               designatedPort(5),
               masterPort(6)
        }
        MAX-ACCESS  read-only
        STATUS  current
        DESCRIPTION
              " Actual role of port in stp."
        ::= { qtechStpExtPortEntry  4 }

--qtechStpPortIfRunSTP OBJECT-TYPE
--        SYNTAX TruthValue
--        MAX-ACCESS read-write
--        STATUS current
--        DESCRIPTION
--            "When the value is true the port will take part in the spanning tree algorithm,
--             that is, if the topology of a port is changed will this be sensed by the algorithm
--             or not."
--        ::= { qtechStpExtPortEntry 5 }

-- -------------------------------------------------------------
-- RSTP / CIST ieee 802.1s-d14-1 12.8.1
-- -------------------------------------------------------------
-- Addition to the dot1dStp group
qtechStpVersion OBJECT-TYPE
    SYNTAX      INTEGER {
                    stpCompatible(0),
                    rstp(2),
                    mstp(3)
                }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "The version of Spanning Tree Protocol the bridge is
         currently running.  The value 'stpCompatible(0)'
         indicates the Spanning Tree Protocol specified in
         IEEE 802.1D , 'rstp(2)' indicates the Rapid Spanning
         Tree Protocol specified in IEEE 802.1w mstp(3) indicates 
         the Multiple spanning tree protocol specified in 
         IEEE 802.1s.  New value may be defined as future versions 
         of the protocol become available."
    REFERENCE
        "IEEE 802.1w clause 14.8.1, 17.12, 17.16.1"
    DEFVAL      { mstp }
    ::= { qtechRstpMIBObjects 1 }

qtechStpTxHoldCount OBJECT-TYPE
    SYNTAX      Integer32 (1..10)
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "The value used by the Port Transmit state machine to limit
         the maximum transmission rate."
    REFERENCE
        "IEEE 802.1w clause 17.16.6"
    DEFVAL      { 3 }
    ::= { qtechRstpMIBObjects 2 }

qtechStpPathCostDefault OBJECT-TYPE
    SYNTAX      INTEGER {
                    stp8021d1998(1),
                    stp8021t2001(2)
                }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "The version of the Spanning Tree default Path Costs that
         are to be used by this Bridge.  A value of 8021d1998(1)
         uses the 16-bit default Path Costs from IEEE Std. 802.1D-1998.
         A value of stp8021t2001(2) uses the 32-bit default Path
         Costs from IEEE Std. 802.1t."
    REFERENCE
        "IEEE 802.1D & 802.1t Table 8-5"
    ::= { qtechRstpMIBObjects 3 }

qtechRstpExtPortTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF QtechRstpExtPortEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "A table that contains port-specific Rapid Spanning Tree
         information."
    ::= { qtechRstpMIBObjects 4 }

qtechRstpExtPortEntry OBJECT-TYPE
    SYNTAX      QtechRstpExtPortEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "A list of Rapid Spanning Tree information maintained by
         each port."
    INDEX    { qtechRstpExtPortIfIndex }
    ::= { qtechRstpExtPortTable 1 }

QtechRstpExtPortEntry ::=
    SEQUENCE {
        qtechRstpExtPortIfIndex    
            IfIndex,
        qtechStpPortProtocolMigration
            TruthValue,
        qtechStpPortAdminEdgePort
            TruthValue,
        qtechStpPortOperEdgePort
            TruthValue,
        qtechStpPortAdminPointToPoint
            INTEGER,
        qtechStpPortOperPointToPoint
            TruthValue,
	qtechStpPortBpduGuard
	    EnabledStatus,
	qtechStpPortBpduFilter	    
	    EnabledStatus		    
    }
qtechRstpExtPortIfIndex OBJECT-TYPE
        SYNTAX IfIndex
        MAX-ACCESS read-only
        STATUS current
        DESCRIPTION
            "include only physical port and trunk port "
        ::= { qtechRstpExtPortEntry 1 }
        
qtechStpPortProtocolMigration OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "When operating in RSTP (version 2) mode, writing TRUE(1)
         to this object forces this port to transmit RSTP BPDUs.
         Any other operation on this object has no effect and
         it always returns FALSE(2) when read."
    REFERENCE
        "IEEE 802.1w clause 14.8.2.4, 17.18.10, 17.26"
    ::= { qtechRstpExtPortEntry 2 }

qtechStpPortAdminEdgePort OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "The administrative value of the Edge Port parameter.  A
         value of TRUE(1) indicates that this port should be
         assumed as an edge-port and a value of FALSE(2) indicates
         that this port should be assumed as a non-edge-port."
    REFERENCE
        "IEEE 802.1t clause 14.8.2, 18.3.3"
    ::= { qtechRstpExtPortEntry 3 }

qtechStpPortOperEdgePort OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The operational value of the Edge Port parameter.  The
         object is initialized to the value of
         qtechStpPortAdminEdgePort and is set FALSE on reception of
         a BPDU."
    REFERENCE
        "IEEE 802.1t clause 14.8.2, 18.3.4"
    ::= { qtechRstpExtPortEntry 4 }

qtechStpPortAdminPointToPoint OBJECT-TYPE
    SYNTAX      INTEGER {
                    forceTrue(0),
                    forceFalse(1),
                    auto(2)
                }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "The administrative point-to-point status of the LAN segment
         attached to this port.  A value of forceTrue(0) indicates that
         this port should always be treated as if it is connected to
         a point-to-point link.  A value of forceFalse(1) indicates
         that this port should be treated as having a shared media
         connection.  A value of auto(2) indicates that this port is
         considered to have a point-to-point link if it is an Aggregator
         and all of its members are aggregatable, or if the MAC entity
         is configured for full duplex operation, either through
         auto-negotiation or by management means."
   REFERENCE
       "IEEE 802.1w clause 6.4.3, 6.5, 14.8.2"
   ::= { qtechRstpExtPortEntry 5 }

qtechStpPortOperPointToPoint OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The operational point-to-point status of the LAN segment
         attached to this port.  It indicates whether a port is
         considered to have a point-to-point connection or not.
         The value is determined by management or by auto-detection,
         as described in the qtechStpPortAdminPointToPoint object."
    REFERENCE
        "IEEE 802.1w clause 6.4.3, 6.5, 14.8.2"
    ::= { qtechRstpExtPortEntry 6 }
    
qtechStpPortBpduGuard  OBJECT-TYPE
    SYNTAX      EnabledStatus
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "
         The BPDU guard feature provides a secure response to invalid configurations because
         you must manually put the port back in service. Use the BPDU guard feature in a 
         service-provider network to  prevent an access port from participating in the 
         spanning tree.
                 
         When the port receives a BPDU, it is put in the error-disabled state if you enable
         BPDU guard feature of this port.
        "
   ::= { qtechRstpExtPortEntry 7 }
   
qtechStpPortBpduFilter  OBJECT-TYPE
    SYNTAX      EnabledStatus
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "It will prevent the port from sending or receiving BPDUs if you enable
         BPDU filter feature of this port. "
   ::= { qtechRstpExtPortEntry 8 }   

qtechStpBpduGuard OBJECT-TYPE
    SYNTAX      EnabledStatus
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "If you enable Global BPDU guard feature ,ports which is EdgePort will
         is put in the error-disabled state When thest ports receives a BPDU."
    ::= { qtechRstpMIBObjects 5 }
    
qtechStpBpduFilter OBJECT-TYPE
    SYNTAX      EnabledStatus
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "If you enable Global BPDU filter feature ,ports which is EdgePort will
        be prevented the port from sending or receiving BPDUs."
    ::= { qtechRstpMIBObjects 6 }    
 
--MSTP addition
qtechStpCistRegionRoot OBJECT-TYPE
    SYNTAX  BridgeId
    MAX-ACCESS  read-only
    STATUS  current
    DESCRIPTION
        "The Bridge Identifier of the current CIST Regional Root."
    REFERENCE
        "IEEE 802.1s-d14-1: Section 12.8.1.1.3"        
    ::= { qtechRstpMIBObjects 7 }

qtechStpCistPathCost OBJECT-TYPE
    SYNTAX  Integer32
    MAX-ACCESS  read-only
    STATUS  current
    DESCRIPTION
        "The CIST path cost from the transmitting Bridge to the CIST Regional Root.."
    REFERENCE
        "IEEE 802.1s-d14-1: Section 12.8.1.1.3"        
    ::= { qtechRstpMIBObjects 8 }
    
    
--qtechStpPortCistTable OBJECT-TYPE
--      SYNTAX      SEQUENCE OF QtechStpPortCistEntry
--      MAX-ACCESS  not-accessible
--      STATUS      current
--      DESCRIPTION
--        "A table containing the spanning tree port path cost
--        configuration when stpxSpanningTreePathCostMode is
--        long(2),

--        If the value of stpxSpanningTreePathCostMode is short(1),
--        this table is not instantiated."
--    ::= { qtechRstpMIBObjects 9 }

--qtechStpPortCistEntry OBJECT-TYPE
--    SYNTAX      QtechStpPortCistEntry
--    MAX-ACCESS  not-accessible
--    STATUS      current
--    DESCRIPTION
--        "A conceptual row containing the spanning tree port path cost
--         configuration."
--     AUGMENTS   { qtechRstpExtPortEntry }
--    ::= { qtechStpPortCistTable 1 }

--QtechStpPortCistEntry ::= SEQUENCE {
--        qtechStpPortCistRegionRoot BridgeId,
--        qtechStpPortCistPathCost Counter32
--        qtechStpPortHelloTime Integer32
--}

--qtechStpPortCistRegionRoot OBJECT-TYPE
--    SYNTAX      BridgeId
--    MAX-ACCESS  read-only
--    STATUS      current
--    DESCRIPTION
--         "The Bridge Identifier of the current CIST Regional Root."
--    REFERENCE
--        "IEEE 802.1s-d14-1: Section 12.8.2.1.3"           
--    ::= { qtechStpPortCistEntry 1}   


--qtechStpPortCistPathCost OBJECT-TYPE
--    SYNTAX      Counter32
--    MAX-ACCESS  read-only
--    STATUS      current
--    DESCRIPTION
--         "The CIST path cost from the transmitting Bridge to the CIST Regional Root."
--    REFERENCE
--        "IEEE 802.1s-d14-1: Section 12.8.2.1.3"           
--    ::= { qtechStpPortCistEntry 2}   


--qtechStpPortHelloTime OBJECT-TYPE
--    SYNTAX      Integer32
--    MAX-ACCESS  read-write
--    STATUS      current
--    DESCRIPTION
--         "The administrative value of Hello Time for the Port."
--    REFERENCE
--        "IEEE 802.1s-d14-1: Section 12.8.2.1.3"           
--    ::= { qtechStpPortCistEntry 3}   

-- -------------------------------------------------------------
-- MSTP / MSTI 802.1s-d14-1 12.8.1
-- -------------------------------------------------------------
qtechStpMstiMaxInstanceNumber  OBJECT-TYPE
    SYNTAX      Integer32 
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
       "The maximum MST (Multiple Spanning Tree) instance id, 
       that are supported by the device for the MST Protocol." 
    ::= { qtechMstpMIBObjects 1}

qtechStpMstiRegionName OBJECT-TYPE
    SYNTAX      DisplayString (SIZE(0..32))  
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
       "The operational MST region name."  
    ::= { qtechMstpMIBObjects 2}

qtechStpMstiRegionRevision OBJECT-TYPE
    SYNTAX      Integer32 (0..65535) 
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
       "The operational MST region version."  
    ::= { qtechMstpMIBObjects 3 } 

qtechStpMstiMaxHopNumber OBJECT-TYPE
    SYNTAX      Integer32 (1..40) 
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
       "The operational MST region max hop number."  
    DEFVAL { 20 }       
    ::= { qtechMstpMIBObjects 4 } 


qtechStpMstiInstanceTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF QtechStpMstiInstanceEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
       "This table contains MST instance information with 
       one entry for each MST instance numbered from 0 
       to qtechStpxMSTMaxInstanceNumber." 
    ::= {qtechMstpMIBObjects 5 }

qtechStpMstiInstanceEntry OBJECT-TYPE
    SYNTAX      QtechStpMstiInstanceEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
       "A conceptual row containing the MST instance 
       information."
    INDEX  { qtechStpMstiInstanceIndex }
    ::= { qtechStpMstiInstanceTable 1 }

QtechStpMstiInstanceEntry ::= SEQUENCE {
    qtechStpMstiInstanceIndex Integer32,
    qtechStpMstiInstanceVlansAddMapped OCTET STRING,
    qtechStpMstiInstanceVlansDeleteMapped OCTET STRING,
    qtechStpMstiInstanceVlansGetMapped OCTET STRING,
    qtechStpMstiInstanceRemainingHopCount Integer32,
    qtechStpMstiPriority Integer32,
--    qtechStpMstiBridgeId Integer32,
    qtechStpMstiTimeSinceTopologyChange TimeTicks,
    qtechStpMstiTopChanges Integer32,
--    qtechStpMstiTopChanged TruthValue,
    qtechStpMstiDesignatedRoot BridgeId,
    qtechStpMstiRootCost Integer32,
    qtechStpMstiRootPort Integer32,
    qtechStpMstiInstanceEntryStatus ConfigStatus

}

qtechStpMstiInstanceIndex OBJECT-TYPE
    SYNTAX      Integer32 (1..64) 
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
       "An integer that uniquely identifies an MST instance 
       from 0 to the object value of qtechStpMstiMaxInstanceNumber."  
    ::= {qtechStpMstiInstanceEntry 1 }

qtechStpMstiInstanceVlansAddMapped OBJECT-TYPE
    SYNTAX     OCTET STRING (SIZE (512))
    MAX-ACCESS read-create
    STATUS     current
    DESCRIPTION
       "A string of octets containing one bit per VLAN. The
       first octet corresponds to VLANs with VlanIndex values
       of 0 through 7; the second octet to VLANs 8 through
       15; etc.  The most significant bit of each octet
       corresponds to the lowest value VlanIndex in that octet.

       For each VLAN, if it is mapped to this MST instance, 
       then the bit corresponding to that VLAN is set to '1'."
    ::= {qtechStpMstiInstanceEntry 2 }

qtechStpMstiInstanceVlansDeleteMapped OBJECT-TYPE
    SYNTAX     OCTET STRING (SIZE (512))
    MAX-ACCESS read-create
    STATUS     current
    DESCRIPTION
       "A string of octets containing one bit per VLAN. The
       first octet corresponds to VLANs with VlanIndex values
       of 0 through 7; the second octet to VLANs 8 through
       15; etc.  The most significant bit of each octet
       corresponds to the lowest value VlanIndex in that octet.

       For each VLAN, if it is mapped to this MST instance, 
       then the bit corresponding to that VLAN is set to '1'."
    ::= {qtechStpMstiInstanceEntry 3 }
    
qtechStpMstiInstanceVlansGetMapped OBJECT-TYPE
    SYNTAX     OCTET STRING (SIZE (512))
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
       "A string of octets containing one bit per VLAN. The
       first octet corresponds to VLANs with VlanIndex values
       of 0 through 7; the second octet to VLANs 8 through
       15; etc.  The most significant bit of each octet
       corresponds to the lowest value VlanIndex in that octet.

       For each VLAN, if it is mapped to this MST instance, 
       then the bit corresponding to that VLAN is set to '1'."
    ::= {qtechStpMstiInstanceEntry 4 }

qtechStpMstiInstanceRemainingHopCount OBJECT-TYPE
    SYNTAX     Integer32 (0..40)
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
        "The remaining hop count for this MST instance."
    ::= {qtechStpMstiInstanceEntry 5 }
    
qtechStpMstiPriority  OBJECT-TYPE
    SYNTAX     Integer32 (0..65535)
    MAX-ACCESS read-create
    STATUS     current
    DESCRIPTION
        "The Bridge priority for the spanning tree instance identified
	by the MSTID."
    REFERENCE
        "IEEE 802.1s-d14-1: Section 12.8.1.2.3."
    DEFVAL { 32768 }	
    ::= {qtechStpMstiInstanceEntry 6 }  
    
--qtechStpMstiBridgeId  OBJECT-TYPE
--    SYNTAX     BridgeId
--    MAX-ACCESS read-only
--    STATUS     current
--    DESCRIPTION
--        "The Bridge Identifier for the spanning tree instance identified
--	by the MSTID."
--    REFERENCE
--        "IEEE 802.1s-d14-1: Section 12.8.1.2.3."
    	
--    ::= {qtechStpMstiInstanceEntry 5 }      
    
qtechStpMstiTimeSinceTopologyChange  OBJECT-TYPE
    SYNTAX     TimeTicks
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
        "Ccount in (in hundredths of a second) of the time elapsed since tcWhile (13.21) was last
         non-zero for any Port for the given MSTI."
    REFERENCE
        "IEEE 802.1s-d14-1: Section 12.8.1.2.3."
    	
    ::= {qtechStpMstiInstanceEntry 7 }          
    
qtechStpMstiTopChanges  OBJECT-TYPE
    SYNTAX     Integer32
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
        "Count of the times tcWhile (13.21) has been non-zero for any Port for the
	given MSTI since the Bridge was powered on or initialized."
    REFERENCE
        "IEEE 802.1s-d14-1: Section 12.8.1.2.3."
    	
    ::= {qtechStpMstiInstanceEntry 8 }          

--qtechStpMstiTopChanged  OBJECT-TYPE
--    SYNTAX     TruthValue
--    MAX-ACCESS read-only
--    STATUS     current
--    DESCRIPTION
--        "True if tcWhile is non-zero for any Port for the given MST."
--    REFERENCE
--        "IEEE 802.1s-d14-1: Section 12.8.1.2.3."
    	
--    ::= {qtechStpMstiInstanceEntry 8 }          
 
qtechStpMstiDesignatedRoot  OBJECT-TYPE
    SYNTAX     BridgeId
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
        "The Bridge Identifier of the Root Bridge for the spanning tree instance
	identified by the MSTID."
    REFERENCE
        "IEEE 802.1s-d14-1: Section 12.8.1.2.3."
    	
    ::= {qtechStpMstiInstanceEntry 9 }         
    
qtechStpMstiRootCost  OBJECT-TYPE
    SYNTAX     Integer32
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
        "The path cost from the transmitting Bridge to the Root Bridge for the
	spanning tree instance identified by the MSTID."
    REFERENCE
        "IEEE 802.1s-d14-1: Section 12.8.1.2.3."
    	
    ::= {qtechStpMstiInstanceEntry 10 }         
    
qtechStpMstiRootPort  OBJECT-TYPE
    SYNTAX     Integer32
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
        "The Root Port for the spanning tree instance identified by the MSTID."
    REFERENCE
        "IEEE 802.1s-d14-1: Section 12.8.1.2.3."
    	
    ::= {qtechStpMstiInstanceEntry 11 }         

qtechStpMstiInstanceEntryStatus OBJECT-TYPE
        SYNTAX ConfigStatus
        MAX-ACCESS read-create
        STATUS current
        DESCRIPTION
            "Status of this entry, set this object to valid will creat a entry,
             and set its value to invalid will delete this entry."
    ::= { qtechStpMstiInstanceEntry 12 }
        
qtechStpPortMstiInstanceTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF QtechStpPortMstiInstanceEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
       "This table contains MST instance information with 
       one entry for each MST instance numbered from 0 
       to qtechStpxMSTMaxInstanceNumber." 
    ::= {qtechMstpMIBObjects 6 }

qtechStpPortMstiInstanceEntry OBJECT-TYPE
    SYNTAX      QtechStpPortMstiInstanceEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
       "A conceptual row containing pthe MST instance 
       information of a bridge port."
    INDEX  { qtechStpMstiInstanceIndex, qtechStpPortMstiIndex}
    ::= { qtechStpPortMstiInstanceTable 1 }

QtechStpPortMstiInstanceEntry ::= SEQUENCE {
    qtechStpPortMstiIndex Integer32,
--    qtechStpPortMstiUpTime TimeTicks,
    qtechStpPortMstiState INTEGER,
--    qtechStpPortMstiEnable INTEGER,
--    qtechStpPortMstiPortId OCTET STRING,
    qtechStpPortMstiAdminPathCost Integer32,
    qtechStpPortMstiOperPathCost Counter32,
    qtechStpPortMstiPriority Integer32,
    qtechStpPortMstiDesignatedRoot BridgeId,
    qtechStpPortMstiDesignatedCost Integer32,
    qtechStpPortMstiDesignatedBridge BridgeId,
    qtechStpPortMstiDesignatedPort OCTET STRING,
    qtechStpPortMstiPortRole INTEGER,
    qtechStpPortMstiPortForwardTransitions Integer32
    
}

qtechStpPortMstiIndex OBJECT-TYPE
    SYNTAX      Integer32
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
       "The value of dot1dBasePort (i.e. dot1dBridge.1.4)
                 for the bridge port."  
    REFERENCE
               "dot1dBasePort is defined in RFC1493."
                 
    ::= {qtechStpPortMstiInstanceEntry 1 }

--qtechStpPortMstiUpTime  OBJECT-TYPE
--    SYNTAX     TimeTicks
--    MAX-ACCESS read-only
--    STATUS     current
--    DESCRIPTION
--        "Count in seconds of the time elapsed since the Port was last reset or initialized."
--    REFERENCE
--        "IEEE 802.1s-d14-1: Section 12.8.2.2.3."
    	
--    ::= {qtechStpPortMstiInstanceEntry 2 }           

qtechStpPortMstiState  OBJECT-TYPE
     SYNTAX      INTEGER {
   	        	disabled(1),
        	        blocking(2),
                        listening(3),
                        learning(4),
                        forwarding(5),
                        broken(6),
                        discard(7)
                    }
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
        "The current state of the Port."
    REFERENCE
        "IEEE 802.1s-d14-1: Section 12.8.2.2.3."
    	
    ::= {qtechStpPortMstiInstanceEntry 2 }        

--qtechStpPortMstiEnable  OBJECT-TYPE
--     SYNTAX      INTEGER {
--   	        	enabled(1),
--        	        disabled(2)
--                    }
--    MAX-ACCESS read-write
--    STATUS     current
--    DESCRIPTION
--        "The enabled/disabled status of the port."
--    REFERENCE
--        "IEEE 802.1s-d14-1: Section 12.8.2.2.3."
    	
--    ::= {qtechStpPortMstiInstanceEntry 3 }        

--qtechStpPortMstiPortId  OBJECT-TYPE
--    SYNTAX     OCTET STRING (SIZE (2))
--    MAX-ACCESS read-only
--    STATUS     current
--    DESCRIPTION
--        "The Port Identifier of the port on the Designated
--        Bridge for this port's segment."
--    REFERENCE
--        "IEEE 802.1s-d14-1: Section 12.8.2.2.3."
    	
--    ::= {qtechStpPortMstiInstanceEntry 4 }       

qtechStpPortMstiAdminPathCost  OBJECT-TYPE
    SYNTAX     Integer32
    MAX-ACCESS read-write
    STATUS     current
    DESCRIPTION
              "The contribution of this port to the path cost of
              paths towards the spanning tree root which include
              this port.  802.1D-1990 recommends that the
              default value of this parameter be in inverse
              proportion to the speed of the attached LAN.
              Setting this value to 0 indicates that port's real
              path cost will be automaticly assigned by system
              according to duplex and speed of the port.Setting 
              this value to other value and system will assigned this 
              value to the port."
    REFERENCE
        "IEEE 802.1s-d14-1: Section 12.8.2.2.3."
    	
    ::= {qtechStpPortMstiInstanceEntry 3 }      

qtechStpPortMstiOperPathCost  OBJECT-TYPE
    SYNTAX     Counter32
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
        " Actual oper value of port cost of msti."
    REFERENCE
        "IEEE 802.1s-d14-1: Section 12.8.2.2.3."
    	
    ::= {qtechStpPortMstiInstanceEntry 4 }      

qtechStpPortMstiPriority  OBJECT-TYPE
    SYNTAX     Integer32
    MAX-ACCESS read-write
    STATUS     current
    DESCRIPTION
        "The value of the priority field which is contained in
        the first (in network byte order) octet of the (2 octet
        long) Port ID."
    REFERENCE
        "IEEE 802.1s-d14-1: Section 12.8.2.2.3."
    DEFVAL { 128 }    	
    ::= {qtechStpPortMstiInstanceEntry 5 }      

qtechStpPortMstiDesignatedRoot  OBJECT-TYPE
    SYNTAX     BridgeId
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
        "The unique Bridge Identifier of the Bridge
        recorded as the Root."
    REFERENCE
        "IEEE 802.1s-d14-1: Section 12.8.2.2.3."
    	
    ::= {qtechStpPortMstiInstanceEntry 6 }      

qtechStpPortMstiDesignatedCost  OBJECT-TYPE
    SYNTAX     Integer32
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
        "The path cost of the Designated Port of the segment
        connected to this port."
    REFERENCE
        "IEEE 802.1s-d14-1: Section 12.8.2.2.3."
    	
    ::= {qtechStpPortMstiInstanceEntry 7 }        

qtechStpPortMstiDesignatedBridge  OBJECT-TYPE
    SYNTAX     BridgeId
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
        "The Bridge Identifier of the bridge which this
        port considers to be the Designated Bridge for
        this port's segment."
    REFERENCE
        "IEEE 802.1s-d14-1: Section 12.8.2.2.3."
    	
    ::= {qtechStpPortMstiInstanceEntry 8 }    

qtechStpPortMstiDesignatedPort  OBJECT-TYPE
    SYNTAX     OCTET STRING (SIZE (2))
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
        "The Port Identifier of the port on the Designated
         Bridge for this port's segment."
    REFERENCE
        "IEEE 802.1s-d14-1: Section 12.8.2.2.3."
    	
    ::= {qtechStpPortMstiInstanceEntry 9 }    

qtechStpPortMstiPortRole  OBJECT-TYPE
    SYNTAX  INTEGER {
               disabledPort(1),
               alternatePort(2),
               backupPort(3),
               rootPort(4),
               designatedPort(5),
               masterPort(6)
        }
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
        " Actual role of port in msti."
    ::= {qtechStpPortMstiInstanceEntry 10 }    
    
qtechStpPortMstiPortForwardTransitions  OBJECT-TYPE
    SYNTAX  Integer32
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
        "The number of times this port has transitioned
         from the Learning state to the Forwarding state in msti."
    ::= {qtechStpPortMstiInstanceEntry 11 }    

    
    
qtechStpMstiReset  OBJECT-TYPE
    SYNTAX Integer32
    MAX-ACCESS read-write
    STATUS current
    DESCRIPTION
            "This object allow of resetting  MST configuration
            parameter reset to default settings. set its value to any
            but 0, will cause agent reset the parameters, set it to 0
            will cause no action. this operation may cause some interval
            the station can not connect the agent depending on the
            parameters previous set."
    ::= { qtechMstpMIBObjects 7}
    
qtechStpCistVlansAddMapped OBJECT-TYPE
    SYNTAX  OCTET STRING
    MAX-ACCESS  read-write
    STATUS  current
    DESCRIPTION
       "A string of octets containing one bit per VLAN. The
       first octet corresponds to VLANs with VlanIndex values
       of 0 through 7; the second octet to VLANs 8 through
       15; etc.  The most significant bit of each octet
       corresponds to the lowest value VlanIndex in that octet.

       For each VLAN, if it is mapped to this MST instance, 
       then the bit corresponding to that VLAN is set to '1'."
    ::= { qtechMstpMIBObjects 8 }

qtechStpCistVlansGetMapped OBJECT-TYPE
    SYNTAX  OCTET STRING
    MAX-ACCESS  read-only
    STATUS  current
    DESCRIPTION
       "A string of octets containing one bit per VLAN. The
       first octet corresponds to VLANs with VlanIndex values
       of 0 through 7; the second octet to VLANs 8 through
       15; etc.  The most significant bit of each octet
       corresponds to the lowest value VlanIndex in that octet.

       For each VLAN, if it is mapped to this MST instance, 
       then the bit corresponding to that VLAN is set to '1'."
    ::= { qtechMstpMIBObjects 9 }
    

qtechStpCistRemainingHopCount OBJECT-TYPE
    SYNTAX  Integer32
    MAX-ACCESS  read-only
    STATUS  current
    DESCRIPTION
        "The remaining hop count for CIST."
    ::= { qtechMstpMIBObjects 10 }


-- -------------------------------------------------------------
-- rstpMIB - Conformance Information
-- -------------------------------------------------------------


stpExternConformance OBJECT IDENTIFIER ::= { qtechStpMIB 4 }

stpExternGroups OBJECT IDENTIFIER ::= { stpExternConformance 1 }

-- stpExternCompliances OBJECT IDENTIFIER ::= { stpExternConformance 2 }

-- -------------------------------------------------------------
-- Units of conformance
-- -------------------------------------------------------------

stpExternGroup OBJECT-GROUP
    OBJECTS {
        qtechSysStpStatus,
        qtechSysStpReset,
        qtechStpPortIfIndex,
        qtechStpPortAdminPathCost,
        qtechStpPortOperPathCost,
        qtechStpPortRole
--        qtechStpPortIfRunSTP
    }
    STATUS      current
    DESCRIPTION
        "Spanning Tree extern information for the bridge."
    ::= { stpExternGroups 1 }

-- -------------------------------------------------------------
-- Compliance statements
-- -------------------------------------------------------------
--stpExternCompliance MODULE-COMPLIANCE
--    STATUS      current
--    DESCRIPTION
--        "The compliance statement for device support of bridging
--         services."
--         
--    MODULE
--        MANDATORY-GROUPS {
--            stpExternGroup
--            }
--        OBJECT           dot1dStpPortPathCost
--        MIN-ACCESS       read-only
--        DESCRIPTION     "Write access is not required."
--        
--        OBJECT           dot1dStpPortEnable
--        MIN-ACCESS       read-only
--        DESCRIPTION     "Write access is not required."
--          
--        OBJECT           dot1dStpHoldTime
--        MIN-ACCESS       not-accessible
--        DESCRIPTION     "Access is not required."  
--            
--        OBJECT           dot1dStpPortState
--        SYNTAX           INTEGER {
--                          disabled(1),
--                          blocking(2),
--                          listening(3),
--                          learning(4),
--                          forwarding(5),
--                          broken(6),
--                          discard(7)
--                      }
--        DESCRIPTION     "Add a new syntax."
--            
--    ::= { stpExternCompliances 1 }




-- -------------------------------------------------------------
-- rstpMIB - Conformance Information
-- -------------------------------------------------------------

rstpConformance OBJECT IDENTIFIER ::= { qtechStpMIB 5 }

rstpGroups OBJECT IDENTIFIER ::= { rstpConformance 1 }

rstpCompliances OBJECT IDENTIFIER ::= { rstpConformance 2 }

-- -------------------------------------------------------------
-- Units of conformance
-- -------------------------------------------------------------

rstpBridgeGroup OBJECT-GROUP
    OBJECTS {
        qtechStpVersion,
        qtechStpTxHoldCount,
        qtechStpBpduGuard,
        qtechStpBpduFilter
    }
    STATUS      current
    DESCRIPTION
        "Rapid Spanning Tree information for the bridge."
    ::= { rstpGroups 1 }

rstpDefaultPathCostGroup OBJECT-GROUP
    OBJECTS {
        qtechStpPathCostDefault

    }
    STATUS      current
    DESCRIPTION
        "Default Spanning Tree path cost information."
    ::= { rstpGroups 2 }

rstpPortGroup OBJECT-GROUP
    OBJECTS {
        qtechRstpExtPortIfIndex,
        qtechStpPortProtocolMigration,
        qtechStpPortAdminEdgePort,
        qtechStpPortOperEdgePort,
        qtechStpPortAdminPointToPoint,
        qtechStpPortOperPointToPoint,
        qtechStpPortBpduGuard,
        qtechStpPortBpduFilter,
--        qtechStpPortCistRegionRoot,
--        qtechStpPortCistPathCost,
--        qtechStpPortHelloTime,
        qtechStpCistRegionRoot,
        qtechStpCistPathCost
        
    }
    STATUS      current
    DESCRIPTION
        "Rapid Spanning Tree information for individual ports."
    ::= { rstpGroups 3 }

-- -------------------------------------------------------------
-- Compliance statements
-- -------------------------------------------------------------

rstpCompliance MODULE-COMPLIANCE
    STATUS      current
    DESCRIPTION
        "The compliance statement for device support of bridging
         services."

    MODULE
        MANDATORY-GROUPS {
            rstpBridgeGroup,
            rstpDefaultPathCostGroup,
            rstpPortGroup
        }

        GROUP rstpDefaultPathCostGroup
            DESCRIPTION
                "Support for this group is mandatory only if
                 both 16-bit and 32-bit Path Costs are supported."
    ::= { rstpCompliances 1 }
    

-- -------------------------------------------------------------
-- mstpMIB - Conformance Information
-- -------------------------------------------------------------

mstpConformance OBJECT IDENTIFIER ::= { qtechStpMIB 6 }

mstpGroups OBJECT IDENTIFIER ::= { mstpConformance 1 }

mstpCompliances OBJECT IDENTIFIER ::= { mstpConformance 2 }

-- -------------------------------------------------------------
-- Units of conformance
-- -------------------------------------------------------------

mstpBridgeRegionGroup OBJECT-GROUP
    OBJECTS {
    	qtechStpMstiMaxInstanceNumber,
    	qtechStpMstiRegionName,
    	qtechStpMstiRegionRevision,
    	qtechStpMstiMaxHopNumber
    	
    }
    STATUS      current
    DESCRIPTION
        "Msti information for the bridge."
    ::= { mstpGroups 1 }

mstpMstiBridgeGroup OBJECT-GROUP
    OBJECTS {
	qtechStpMstiInstanceIndex,
    qtechStpMstiInstanceVlansAddMapped,
    qtechStpMstiInstanceVlansDeleteMapped,
    qtechStpMstiInstanceVlansGetMapped,
    	qtechStpMstiInstanceRemainingHopCount,
    	qtechStpMstiPriority,
--    	qtechStpMstiBridgeId,
    	qtechStpMstiTimeSinceTopologyChange,
    	qtechStpMstiTopChanges,
--    	qtechStpMstiTopChanged,
    	qtechStpMstiDesignatedRoot,
    	qtechStpMstiRootCost,
    	qtechStpMstiRootPort,
	qtechStpMstiInstanceEntryStatus    	
    }
    STATUS      current
    DESCRIPTION
        "Default Spanning Tree path cost information."
    ::= { mstpGroups 2 }

mstpMstiPortGroup OBJECT-GROUP
    OBJECTS {
--    	qtechStpPortMstiUpTime,
    	qtechStpPortMstiState,
--    	qtechStpPortMstiEnable,
--    	qtechStpPortMstiPortId,
    	qtechStpPortMstiAdminPathCost,
    	qtechStpPortMstiOperPathCost,
    	qtechStpPortMstiPriority,
    	qtechStpPortMstiDesignatedRoot,
    	qtechStpPortMstiDesignatedCost,
    	qtechStpPortMstiDesignatedBridge,
    	qtechStpPortMstiDesignatedPort,
    	qtechStpPortMstiPortRole,
	qtechStpPortMstiPortForwardTransitions    	
    }
    STATUS      current
    DESCRIPTION
        "Rapid Spanning Tree information for individual ports."
    ::= { mstpGroups 3 }

-- -------------------------------------------------------------
-- Compliance statements
-- -------------------------------------------------------------

mstpCompliance MODULE-COMPLIANCE
    STATUS      current
    DESCRIPTION
        "The compliance statement for device support of bridging
         services."

    MODULE
        MANDATORY-GROUPS {
            mstpBridgeRegionGroup,
            mstpMstiBridgeGroup,
            mstpMstiPortGroup
        }

    ::= { mstpCompliances 1 }
END