-- ***************************************************************** -- QTECH-OSPF-MIB.mib: Qtech Ospf MIB file -- -- November 2002, ChenXingBin -- -- Copyright (c) 2002 by Qtech Networks Co.,Ltd. -- All rights reserved. -- -- ***************************************************************** -- QTECH-OSPF-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, TimeTicks, IpAddress, Unsigned32, Gauge32, Counter32 FROM SNMPv2-SMI TruthValue, RowStatus FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ConfigStatus FROM QTECH-TC EnabledStatus FROM P-BRIDGE-MIB AreaID, Status, PositiveInteger, DesignatedRouterPriority, RouterID, HelloRange FROM OSPF-MIB qtechMgmt FROM QTECH-SMI; qtechOspfMIB MODULE-IDENTITY LAST-UPDATED "200211200000Z" ORGANIZATION "Qtech Networks Co.,Ltd." CONTACT-INFO " Tel: 4008-111-000 E-mail: service@qtech.com.cn" DESCRIPTION "This module defines qtech Ospf mibs." REVISION "200211200000Z" DESCRIPTION "Initial version of this MIB module." ::= { qtechMgmt 30} qtechOspfMIBObjects OBJECT IDENTIFIER ::= { qtechOspfMIB 1 } -- general mib qtechOspfGeneralMibsGroup OBJECT IDENTIFIER ::= { qtechOspfMIBObjects 1 } --Minimum LSA interval qtechOspfMiniLsaInterval OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum LSA interval that the two LSA generate." ::={ qtechOspfGeneralMibsGroup 1 } --Minimum LSA arrival qtechOspfMiniLsaArrival OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum LSA Interval of the two LSA arrival." ::={ qtechOspfGeneralMibsGroup 2 } --Number of areas in this router qtechOspfAreasNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of areas in this router" ::={ qtechOspfGeneralMibsGroup 3 } qtechOspfNormalAreasNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of normal areas in this router" ::={ qtechOspfGeneralMibsGroup 4} qtechOspfStubAreasNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of stub areas in this router" ::={ qtechOspfGeneralMibsGroup 5 } qtechOspfNssaAreasNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of nssa areas in this router" ::={ qtechOspfGeneralMibsGroup 6 } qtechOspfSpfDelay OBJECT-TYPE SYNTAX Unsigned32(0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "Ospf Spf shedule time, an integer from 0 to 65535. The default is 5 seconds,0 means no delay." DEFVAL {5} ::={ qtechOspfGeneralMibsGroup 7 } qtechOspfSpfHoldTime OBJECT-TYPE SYNTAX Unsigned32(0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "hold time between two Spfs.an integer from 0 to 65535. The default is 10 seconds; 0 means no delay." DEFVAL {10} ::={ qtechOspfGeneralMibsGroup 8 } qtechOspfAutoCostRefBandWidthRef OBJECT-TYPE SYNTAX Unsigned32(0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "Set AutoCost bandwidth referenc value in unit of Mbits. Setting this value to 0 indicate that disable the feature of autocost bandwidth referenc." DEFVAL {100} ::={ qtechOspfGeneralMibsGroup 9 } qtechOspfLsaGroupPacing OBJECT-TYPE SYNTAX Unsigned32(10..1800) MAX-ACCESS read-write STATUS current DESCRIPTION "set the group pacing of LSAs." DEFVAL {240} ::={ qtechOspfGeneralMibsGroup 10} qtechOspfInterDistance OBJECT-TYPE SYNTAX Unsigned32(1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Set inter-area distance." DEFVAL {110} ::= { qtechOspfGeneralMibsGroup 11 } qtechOspfIntraDistance OBJECT-TYPE SYNTAX Unsigned32(1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Set intra-area distance." DEFVAL {110} ::= { qtechOspfGeneralMibsGroup 12 } qtechOspfExternDistance OBJECT-TYPE SYNTAX Unsigned32(1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Set extern distance." DEFVAL {110} ::= { qtechOspfGeneralMibsGroup 13 } --LogAdjChangeNotify qtechOspfLogAdjChangeNotify OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "if enabled status is setted, Send syslog message when a neighbor state changes." DEFVAL {enabled} ::= { qtechOspfGeneralMibsGroup 14 } qtechOspfPassiveStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The qtechOspfIfPassiveStatus of a interface equal to this object value when this interface is created. If you change this object value to 'enabled' or 'disabled'all interfaces which have exist will also change their qtechOspfIfPassiveStatus to 'enabled' or 'disabled'." DEFVAL { disabled } ::={ qtechOspfGeneralMibsGroup 15 } qtechOspfRFC1583Compatibility OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Controls the preference rules used in calculating AS external routes (RFC2328 Section 16.4) when choosing among multiple AS-external-LSAs advertising the same destination. When set to 'enabled', the preference rules remain those specified by RFC 1583 ([Ref9]). When set to 'disabled', the preference rules are those stated in 'RFC2328 Section 16.4.1' which prevent routing loops when AS- external-LSAs for the same destination have been originated from different areas. Set to 'enabled' by default." REFERENCE "OSPF Version 2(RFC2328), C.1 Global parameters" DEFVAL { enabled } ::={ qtechOspfGeneralMibsGroup 16 } qtechOspfRouteRedisDefMetricVal OBJECT-TYPE SYNTAX Unsigned32(1..16777214) MAX-ACCESS read-write STATUS current DESCRIPTION "When this value is setted,Cause the current routing protocol(ospf) to use the same metricvalue for all redistributed routes (BGP, RIP, and OSPF)." DEFVAL {20} ::= { qtechOspfGeneralMibsGroup 17} qtechOspfAdminiDistance OBJECT-TYPE SYNTAX Unsigned32(1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "ospf Administrative distance." DEFVAL {110} ::= { qtechOspfGeneralMibsGroup 18} --table mib --qtechOspfAreaTable qtechOspfAreaTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechOspfAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information describing the configured parame- ters and cumulative statistics of the router's attached areas.This table is superset of ospfAreaTable" ::= { qtechOspfMIBObjects 2} qtechOspfAreaEntry OBJECT-TYPE SYNTAX QtechOspfAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of qtechOspfAreaTable." INDEX { qtechOspfAreaId} ::= { qtechOspfAreaTable 1 } QtechOspfAreaEntry ::= SEQUENCE { qtechOspfAreaId AreaID, qtechOspfAuthType INTEGER, qtechOspfImportAsExtern INTEGER, qtechOspfSpfRuns Counter32, qtechOspfAreaBdrRtrCount Gauge32, qtechOspfAsBdrRtrCount Gauge32, qtechOspfAreaLsaCount Gauge32, qtechOspfAreaLsaCksumSum Unsigned32, qtechOspfAreaSummary INTEGER, qtechOspfAreaStatus RowStatus, -- extend parts qtechOspfAreaInterfaceNum Unsigned32, qtechOspfAreaNssaIsRedistribution TruthValue, qtechOspfAreaNssaIsDefInfoOriginate TruthValue } qtechOspfAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { qtechOspfAreaEntry 1 } qtechOspfAuthType OBJECT-TYPE SYNTAX INTEGER{ none(0), simplePassword(1), md5 (2) -- reserved for specification by IANA (> 2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The authentication type specified for an area. Additional authentication types may be assigned locally on a per Area basis." REFERENCE "OSPF Version 2, Appendix E Authentication" DEFVAL { 0 } -- no authentication, by default ::= { qtechOspfAreaEntry 2 } qtechOspfImportAsExtern OBJECT-TYPE SYNTAX INTEGER { importExternal (1), --normal area importNoExternal (2), -- stub area importNssa (3) -- NSSA area } MAX-ACCESS read-create STATUS current DESCRIPTION "The area's support for importing AS external link- state advertisements." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" DEFVAL { importExternal } ::= { qtechOspfAreaEntry 3 } qtechOspfSpfRuns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times that the intra-area route table has been calculated using this area's link-state database. This is typically done using Dijkstra's algorithm." ::= { qtechOspfAreaEntry 4 } qtechOspfAreaBdrRtrCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of area border routers reach- able within this area. This is initially zero, and is calculated in each SPF Pass." ::= { qtechOspfAreaEntry 5 } qtechOspfAsBdrRtrCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass." ::= { qtechOspfAreaEntry 6 } qtechOspfAreaLsaCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of link-state advertisements in this area's link-state database, excluding AS External LSA's." ::= { qtechOspfAreaEntry 7 } qtechOspfAreaLsaCksumSum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The 32-bit unsigned sum of the link-state ad- vertisements' LS checksums contained in this area's link-state database. This sum excludes external (LS type 5) link-state advertisements. The sum can be used to determine if there has been a change in a router's link state data- base, and to compare the link-state database of two routers." DEFVAL { 0 } ::= { qtechOspfAreaEntry 8 } qtechOspfAreaSummary OBJECT-TYPE SYNTAX INTEGER { noAreaSummary (1), sendAreaSummary (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The variable ospfAreaSummary controls the im- port of summary LSAs into stub areas. It has no effect on other areas. If it is noAreaSummary, the router will neither originate nor propagate summary LSAs into the stub area. It will rely entirely on its de- fault route. If it is sendAreaSummary, the router will both summarize and propagate summary LSAs." DEFVAL { sendAreaSummary } ::= { qtechOspfAreaEntry 9 } qtechOspfAreaStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { qtechOspfAreaEntry 10 } qtechOspfAreaInterfaceNum OBJECT-TYPE --for command "show SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " the interface number of this area" ::= { qtechOspfAreaEntry 11 } qtechOspfAreaNssaIsRedistribution OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION " if it's disabled , when the router is an NSSA ABR and you want the redistribute command to import routes into normal areas, but not into the NSSA, this field is vaild for nssa area" DEFVAL {true} ::= { qtechOspfAreaEntry 12} qtechOspfAreaNssaIsDefInfoOriginate OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "if it's enabled it meaning that on an ABR to allow importing type 7 LSAs into the NSSA, this field is valid for nssa area" DEFVAL {false} ::= { qtechOspfAreaEntry 13} --network address scope table qtechOspfAddressScopeTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechOspfAddressScopeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Define an interface on which OSPF runs and the area ID for that interface. You can use the wildcard-mask to use a single command to define one or more multiple interfaces to be associated with a specific OSPF area. " ::= { qtechOspfMIBObjects 3 } qtechOspfAddressScopeEntry OBJECT-TYPE SYNTAX QtechOspfAddressScopeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry define an scope of address for ospf routing." INDEX { qtechOspfNetWorkAreaID,qtechOspfNetWorkAddress, qtechOspfNetWorkMask} ::= { qtechOspfAddressScopeTable 1 } QtechOspfAddressScopeEntry ::= SEQUENCE { qtechOspfNetWorkAreaID IpAddress, qtechOspfNetWorkAddress IpAddress, qtechOspfNetWorkMask IpAddress, qtechOspfNetWorkStatus RowStatus } qtechOspfNetWorkAreaID OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "area ID" ::= { qtechOspfAddressScopeEntry 1 } qtechOspfNetWorkAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " Routing for Networks Ipaddress" ::= { qtechOspfAddressScopeEntry 2 } qtechOspfNetWorkMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " Routing for Networks mask" ::= { qtechOspfAddressScopeEntry 3 } qtechOspfNetWorkStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION " when this value is destroy,the entry will be deleted" ::= { qtechOspfAddressScopeEntry 4 } -- The Ospf Interface Configuration Table qtechOspfIfTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechOspfIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Interface Table describes the interfaces from the viewpoint of OSPF." REFERENCE "ospfIfTable in rfc1850" ::= { qtechOspfMIBObjects 4 } qtechOspfIfEntry OBJECT-TYPE SYNTAX QtechOspfIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Interface Entry describes one inter- face configuration of OSPF." INDEX { qtechOspfIfIpAddress, qtechOspfAddressLessIf } ::= { qtechOspfIfTable 1 } QtechOspfIfEntry ::= SEQUENCE { qtechOspfIfIpAddress IpAddress, qtechOspfAddressLessIf Unsigned32, qtechOspfIfAreaId AreaID, qtechOspfIfType INTEGER, qtechOspfIfAdminStat Status, qtechOspfIfRtrPriority DesignatedRouterPriority, qtechOspfIfTransitDelay Unsigned32, qtechOspfIfRetransInterval Unsigned32, qtechOspfIfHelloInterval HelloRange, qtechOspfIfRtrDeadInterval PositiveInteger, qtechOspfIfPollInterval PositiveInteger, qtechOspfIfState INTEGER, qtechOspfIfDesignatedRouter IpAddress, qtechOspfIfBackupDesignatedRouter IpAddress, qtechOspfIfEvents Counter32, qtechOspfIfAuthType INTEGER, qtechOspfIfAuthKey OCTET STRING, qtechOspfIfStatus RowStatus, qtechOspfIfMulticastForwarding INTEGER, qtechOspfIfDemand TruthValue, qtechOspfIfDatabaseFilterAllOut EnabledStatus, qtechOspfIfDesignateRouterId IpAddress, qtechOspfIfBackupDesignateRouterId IpAddress, qtechOspfIfWaitInternal TimeTicks, qtechOspfIfPassiveStatus EnabledStatus, qtechOspfIfCurrentUsedMd5AuthKeyId Unsigned32 } qtechOspfIfIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of this OSPF interface." ::= { qtechOspfIfEntry 1 } qtechOspfAddressLessIf OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address." ::= { qtechOspfIfEntry 2 } qtechOspfIfAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone." DEFVAL { '00000000'H } -- 0.0.0.0 ::= { qtechOspfIfEntry 3 } qtechOspfIfType OBJECT-TYPE SYNTAX INTEGER { broadcast (1), nbma (2), pointToPoint (3), pointToMultipoint (5), loopback(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broad- cast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast', X.25 and similar technologies take the value 'nbma', and links that are definitively point to point take the value 'pointToPoint'." ::= { qtechOspfIfEntry 4 } qtechOspfIfAdminStat OBJECT-TYPE SYNTAX Status MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF interface's administrative status. The value formed on the interface, and the in- terface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF." ::= { qtechOspfIfEntry 5 } qtechOspfIfRtrPriority OBJECT-TYPE SYNTAX DesignatedRouterPriority MAX-ACCESS read-write STATUS current DESCRIPTION "The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligi- ble to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker." DEFVAL { 1 } ::= { qtechOspfIfEntry 6 } qtechOspfIfTransitDelay OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The estimated number of seconds it takes to transmit a link state update packet over this interface." DEFVAL { 1 } ::= { qtechOspfIfEntry 7 } qtechOspfIfRetransInterval OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets." DEFVAL { 5 } ::= { qtechOspfIfEntry 8 } qtechOspfIfHelloInterval OBJECT-TYPE SYNTAX HelloRange MAX-ACCESS read-write STATUS current DESCRIPTION "The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for all routers attached to a common network." DEFVAL { 10 } ::= { qtechOspfIfEntry 9 } qtechOspfIfRtrDeadInterval OBJECT-TYPE SYNTAX PositiveInteger MAX-ACCESS read-write STATUS current DESCRIPTION "The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network." DEFVAL { 40 } ::= { qtechOspfIfEntry 10 } qtechOspfIfPollInterval OBJECT-TYPE SYNTAX PositiveInteger MAX-ACCESS read-only STATUS current DESCRIPTION "The larger time interval, in seconds, between the Hello packets sent to an inactive non- broadcast multi- access neighbor." ::= { qtechOspfIfEntry 11 } qtechOspfIfState OBJECT-TYPE SYNTAX INTEGER { down (1), loopback (2), waiting (3), pointToPoint (4), designatedRouter (5), backupDesignatedRouter (6), otherDesignatedRouter (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Interface State." DEFVAL { down } ::= { qtechOspfIfEntry 12 } qtechOspfIfDesignatedRouter OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the interface which connected the local router in the Designated Router." DEFVAL { '00000000'H } -- 0.0.0.0 ::= { qtechOspfIfEntry 13 } qtechOspfIfBackupDesignatedRouter OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the interface which connected the local router in the Backup Designated Router." DEFVAL { '00000000'H } -- 0.0.0.0 ::= { qtechOspfIfEntry 14 } qtechOspfIfEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this OSPF interface has changed its state, or an error has occurred." ::= { qtechOspfIfEntry 15 } qtechOspfIfAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-write STATUS current DESCRIPTION "The Authentication Key. If the Area's Author- ization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, qtechOspfIfAuthKey always returns an Oc- tet String of length zero." REFERENCE "OSPF Version 2, Section 9 The Interface Data Structure" DEFVAL { '0000000000000000'H } -- 0.0.0.0.0.0.0.0 ::= { qtechOspfIfEntry 16 } qtechOspfIfStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-only STATUS current DESCRIPTION "This value will be active(1) always." ::= { qtechOspfIfEntry 17 } qtechOspfIfMulticastForwarding OBJECT-TYPE SYNTAX INTEGER { blocked (1), -- no multicast forwarding multicast (2), -- using multicast address unicast (3) -- to each OSPF neighbor } MAX-ACCESS read-only STATUS current DESCRIPTION "The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link uni- casts. Data link multicasting is not meaning- ful on point to point and NBMA interfaces, and setting ospfMulticastForwarding to 0 effective- ly disables all multicast forwarding." DEFVAL { blocked } ::= { qtechOspfIfEntry 18 } qtechOspfIfDemand OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether Demand OSPF procedures (hel- lo supression to FULL neighbors and setting the DoNotAge flag on proogated LSAs) should be per- formed on this interface." DEFVAL { false } ::= { qtechOspfIfEntry 19 } qtechOspfIfAuthType OBJECT-TYPE SYNTAX INTEGER (0..255) -- none (0), -- simplePassword (1) -- md5 (2) -- default (3) -- reserved for specification by IANA (> 2) MAX-ACCESS read-write STATUS current DESCRIPTION "The authentication type specified for an interface. Setting this value to 'default' means using default authentication type referenced to Area Authentication, this value only for set,not be read. Additional authentication types may be assigned locally." REFERENCE "OSPF Version 2, Appendix E Authentication" DEFVAL { 0 } -- no authentication, by default ::= { qtechOspfIfEntry 20 } qtechOspfIfDatabaseFilterAllOut OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Block flooding of OSPF LSA packets to the interface. By default, OSPF floods new LSAs over all interfaces in the same area, except the interface on which the LSA arrives." DEFVAL {disabled} ::= { qtechOspfIfEntry 21 } qtechOspfIfDesignateRouterId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "DR RouterID of this interface, when DR does not selected,DR Id is 0.0.0.0" DEFVAL {'00000000'H} ::= { qtechOspfIfEntry 22 } qtechOspfIfBackupDesignateRouterId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Backup DR RouterId of this interface , when Backup DR does not selected,BDR Id is 0.0.0.0" DEFVAL {'00000000'H} ::= { qtechOspfIfEntry 23 } qtechOspfIfWaitInternal OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The wait time of hello generate" ::= { qtechOspfIfEntry 24 } qtechOspfIfPassiveStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object value to 'enabled' ,the interface will become a passive interface." DEFVAL { disabled } ::= { qtechOspfIfEntry 25 } qtechOspfIfCurrentUsedMd5AuthKeyId OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "key-id which current used for md5 authentication,this value is valid from 1 to 255, the value 0 is default value.." DEFVAL {0} ::= { qtechOspfIfEntry 26 } -- The Ospf Interface MD5 authentication key configuration table qtechOspfIfMd5AuthKeyTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechOspfIfMd5AuthKeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration table of the key-id for md5 authentication for OSPF protocol." ::= { qtechOspfMIBObjects 5 } qtechOspfIfMd5AuthKeyEntry OBJECT-TYPE SYNTAX QtechOspfIfMd5AuthKeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration entry of the key-id for md5 authentication for OSPF protocol" INDEX {qtechOspfIfMd5AuthKeyIf, qtechOspfIfMd5AuthKeyId } ::= { qtechOspfIfMd5AuthKeyTable 1 } QtechOspfIfMd5AuthKeyEntry ::= SEQUENCE { qtechOspfIfMd5AuthKeyIf Unsigned32, qtechOspfIfMd5AuthKeyId Unsigned32, qtechOspfIfMd5AuthKey OCTET STRING, qtechOspfIfMd5AuthKeySt ConfigStatus } qtechOspfIfMd5AuthKeyIf OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Corresponding value of ifIndex for interfaces." ::= { qtechOspfIfMd5AuthKeyEntry 1 } qtechOspfIfMd5AuthKeyId OBJECT-TYPE SYNTAX Unsigned32 (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "the key-id for md5 authentication." ::= { qtechOspfIfMd5AuthKeyEntry 2 } qtechOspfIfMd5AuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-create STATUS current DESCRIPTION "The Authentication Key for MD5. When read, qtechOspfIfMd5AuthKey always returns an Oc- tet String of length zero." REFERENCE "OSPF Version 2, Section 9 The Interface Data Structure" ::= { qtechOspfIfMd5AuthKeyEntry 3 } qtechOspfIfMd5AuthKeySt OBJECT-TYPE SYNTAX ConfigStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this value to 'invalid' will delete this entry. Setting this value to 'valid' will have no effect." ::= { qtechOspfIfMd5AuthKeyEntry 4 } -- The Qtech Ospf Virtual Link Table qtechOspfVirtTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechOspfVirtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about this router's virtual inter- faces.Include ospfVirtIfTable in rfc1850" REFERENCE "ospfVirtIfTable in rfc1850" ::= { qtechOspfMIBObjects 6 } qtechOspfVirtEntry OBJECT-TYPE SYNTAX QtechOspfVirtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a single Virtual Interface" INDEX {qtechOspfVirtIfAreaId, qtechOspfVirtIfNeighbor} ::= { qtechOspfVirtTable 1 } QtechOspfVirtEntry ::= SEQUENCE { qtechOspfVirtIfAreaId AreaID, qtechOspfVirtIfNeighbor RouterID, qtechOspfVirtIfTransitDelay Unsigned32, qtechOspfVirtIfRetransInterval Unsigned32, qtechOspfVirtIfHelloInterval HelloRange, qtechOspfVirtIfRtrDeadInterval PositiveInteger, qtechOspfVirtIfState INTEGER, qtechOspfVirtIfEvents Counter32, qtechOspfVirtIfAuthType INTEGER, qtechOspfVirtIfAuthKey OCTET STRING, qtechOspfVirtIfStatus RowStatus, qtechOspfVirtCost Unsigned32, qtechOspfVirtNativeIfIndex INTEGER, qtechOspfVirtLinkState INTEGER, qtechOspfVirtHelloDueIn TimeTicks, qtechOspfVirtCurrentUsedMd5AuthKeyId Unsigned32 } qtechOspfVirtIfAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0" ::= { qtechOspfVirtEntry 1 } qtechOspfVirtIfNeighbor OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The Router ID of the Virtual Neighbor." ::= { qtechOspfVirtEntry 2 } qtechOspfVirtIfTransitDelay OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The estimated number of seconds it takes to transmit a link- state update packet over this interface." DEFVAL { 1 } ::= { qtechOspfVirtEntry 3 } qtechOspfVirtIfRetransInterval OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets. This value should be well over the expected round- trip time." DEFVAL { 5 } ::= { qtechOspfVirtEntry 4 } qtechOspfVirtIfHelloInterval OBJECT-TYPE SYNTAX HelloRange MAX-ACCESS read-create STATUS current DESCRIPTION "The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for the virtual neighbor." DEFVAL { 10 } ::= { qtechOspfVirtEntry 5 } qtechOspfVirtIfRtrDeadInterval OBJECT-TYPE SYNTAX PositiveInteger MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neigh- bor." DEFVAL { 40 } ::= { qtechOspfVirtEntry 6 } qtechOspfVirtIfState OBJECT-TYPE SYNTAX INTEGER { down (1), -- these use the same encoding pointToPoint (4) -- as the ospfIfTable } MAX-ACCESS read-only STATUS current DESCRIPTION "OSPF virtual interface states." DEFVAL { down } ::= { qtechOspfVirtEntry 7 } qtechOspfVirtIfEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of state changes or error events on this Virtual Link" ::= { qtechOspfVirtEntry 8 } qtechOspfVirtIfAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..256)) MAX-ACCESS read-create STATUS current DESCRIPTION "If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 oc- tets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, ospfVifAuthKey always returns a string of length zero." REFERENCE "OSPF Version 2, Section 9 The Interface Data Structure" DEFVAL { '0000000000000000'H } -- 0.0.0.0.0.0.0.0 ::= { qtechOspfVirtEntry 9 } qtechOspfVirtIfStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { qtechOspfVirtEntry 10 } qtechOspfVirtIfAuthType OBJECT-TYPE SYNTAX INTEGER (0..255) -- none (0), -- simplePassword (1), -- md5 (2), -- default (3) -- reserved for specification by IANA (> 2) MAX-ACCESS read-create STATUS current DESCRIPTION "The authentication type specified for a virtual interface. Setting this value 'default' means using default authentication type referenced to Area Authentication, this value only for set,not be read. Additional authentication types may be assigned locally." REFERENCE "OSPF Version 2, Appendix E Authentication" DEFVAL { 0 } -- no authentication, by default ::= { qtechOspfVirtEntry 11 } qtechOspfVirtCost OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Explicitly specify the cost of sending a packet on the interface." ::= { qtechOspfVirtEntry 12 } qtechOspfVirtNativeIfIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION " the Interface's Index that The Virtual Link via this interface." ::= { qtechOspfVirtEntry 13 } qtechOspfVirtLinkState OBJECT-TYPE SYNTAX INTEGER{ up(1), down(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Virtual Link State is up or down." ::= { qtechOspfVirtEntry 14 } qtechOspfVirtHelloDueIn OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION " the time when hello due in." ::= { qtechOspfVirtEntry 15 } qtechOspfVirtCurrentUsedMd5AuthKeyId OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "the key-id which current used for md5 authentication,this value is valid from 1 to 255, the value 0 is default value." DEFVAL {0} ::= { qtechOspfVirtEntry 16 } -- The Ospf Virtual Interface MD5 authentication key configuration table qtechOspfVirtIfMd5AuthKeyTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechOspfVirtIfMd5AuthKeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration table of the key-id for md5 authentication in VirtIf for OSPF protocol." ::= { qtechOspfMIBObjects 7 } qtechOspfVirtIfMd5AuthKeyEntry OBJECT-TYPE SYNTAX QtechOspfVirtIfMd5AuthKeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Configuration entry of the key-id for md5 authentication in VirtIf for OSPF protocol" INDEX {qtechOspfVirtIfMd5AuthKeyAreaId, qtechOspfVirtIfMd5AuthKeyNeighbor, qtechOspfVirtIfMd5AuthKeyId } ::= { qtechOspfVirtIfMd5AuthKeyTable 1 } QtechOspfVirtIfMd5AuthKeyEntry ::= SEQUENCE { qtechOspfVirtIfMd5AuthKeyAreaId AreaID, qtechOspfVirtIfMd5AuthKeyNeighbor RouterID, qtechOspfVirtIfMd5AuthKeyId Unsigned32, qtechOspfVirtIfMd5AuthKey OCTET STRING, qtechOspfVirtIfMd5AuthKeySt ConfigStatus } qtechOspfVirtIfMd5AuthKeyAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0" ::= { qtechOspfVirtIfMd5AuthKeyEntry 1 } qtechOspfVirtIfMd5AuthKeyNeighbor OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The Router ID of the Virtual Neighbor." ::= { qtechOspfVirtIfMd5AuthKeyEntry 2 } qtechOspfVirtIfMd5AuthKeyId OBJECT-TYPE SYNTAX Unsigned32 (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "the key-id for md5 authentication." ::= { qtechOspfVirtIfMd5AuthKeyEntry 3 } qtechOspfVirtIfMd5AuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-create STATUS current DESCRIPTION "The Authentication Key for MD5. When read, qtechOspfVirtIfMd5AuthKey always returns an Oc- tet String of length zero." REFERENCE "OSPF Version 2, Section 9 The Interface Data Structure" ::= { qtechOspfVirtIfMd5AuthKeyEntry 4 } qtechOspfVirtIfMd5AuthKeySt OBJECT-TYPE SYNTAX ConfigStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this value to 'invalid' will delete this entry. Setting this value to 'valid' will have no effect." ::= { qtechOspfVirtIfMd5AuthKeyEntry 5 } qtechOspfLsaDetailInfoMibsGroup OBJECT IDENTIFIER ::= { qtechOspfMIBObjects 8 } -- OSPF Link State Database -- The Link State Database contains the Link State -- Advertisements from throughout the areas that the -- device is attached to. qtechOspfLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechOspfLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Process's Link State Database." REFERENCE "OSPF Version 2, Section 12 Link State Adver- tisements" ::= { qtechOspfLsaDetailInfoMibsGroup 1 } qtechOspfLsdbEntry OBJECT-TYPE SYNTAX QtechOspfLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A single Link State Advertisement." INDEX { qtechOspfLsdbAreaId, qtechOspfLsdbType, qtechOspfLsdbLsid, qtechOspfLsdbRouterId } ::= { qtechOspfLsdbTable 1 } QtechOspfLsdbEntry ::= SEQUENCE { qtechOspfLsdbAreaId AreaID, qtechOspfLsdbType INTEGER, qtechOspfLsdbLsid IpAddress, qtechOspfLsdbRouterId RouterID, qtechOspfLsdbSequence Unsigned32, qtechOspfLsdbAge Unsigned32, qtechOspfLsdbChecksum Unsigned32, qtechOspfLsdbAdvertisement OCTET STRING, qtechOspfLsdbLinkNum --equal LinkCount Unsigned32, qtechOspfLsdbPacketLength Unsigned32, qtechOspfSummaryLsaNetworkMask IpAddress, qtechOspfSummaryLsaTos0Metric Unsigned32, qtechOspfNssaLsaDetailMetricType INTEGER, qtechOspfNssaLsaDetailForwardAddr IpAddress, qtechOspfNssaLsaDetailRouteTag Unsigned32, qtechOspfLsdbOption Unsigned32 } qtechOspfLsdbAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "The 32 bit identifier of the Area from which the LSA was received." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { qtechOspfLsdbEntry 1 } -- External Link State Advertisements are permitted -- for backward compatibility, but should be displayed in -- the ospfExtLsdbTable rather than here. qtechOspfLsdbType OBJECT-TYPE SYNTAX INTEGER { routerLink (1), networkLink (2), summaryLink (3), asSummaryLink (4), asExternalLink (5), -- but see qtechOspfExtLsdbTable multicastLink (6), nssaExternalLink (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertise- ment format." REFERENCE "OSPF Version 2, Appendix A.4.1 The Link State Advertisement header" ::= { qtechOspfLsdbEntry 2 } qtechOspfLsdbLsid OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement." REFERENCE "OSPF Version 2, Section 12.1.4 Link State ID" ::= { qtechOspfLsdbEntry 3 } qtechOspfLsdbRouterId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The 32 bit number that uniquely identifies the originating router in the Autonomous System." REFERENCE "OSPF Version 2, Appendix C.1 Global parameters" ::= { qtechOspfLsdbEntry 4 } -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It qtechs with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. qtechOspfLsdbSequence OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement." REFERENCE "OSPF Version 2, Section 12.1.6 LS sequence number" ::= { qtechOspfLsdbEntry 5 } qtechOspfLsdbAge OBJECT-TYPE SYNTAX Unsigned32 -- Should be 0..MaxAge MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the age of the link state adver- tisement in seconds." REFERENCE "OSPF Version 2, Section 12.1.1 LS age" ::= { qtechOspfLsdbEntry 6 } qtechOspfLsdbChecksum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum." REFERENCE "OSPF Version 2, Section 12.1.7 LS checksum" ::= { qtechOspfLsdbEntry 7 } qtechOspfLsdbAdvertisement OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "The entire Link State Advertisement, including its header." REFERENCE "OSPF Version 2, Section 12 Link State Adver- tisements" ::= { qtechOspfLsdbEntry 8 } qtechOspfLsdbLinkNum OBJECT-TYPE SYNTAX Unsigned32(0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION " the link count of this Router Link Lsa , this field is only valid for Router Link LsaŁ¨type 1 LSA)" ::= { qtechOspfLsdbEntry 9 } qtechOspfLsdbPacketLength OBJECT-TYPE SYNTAX Unsigned32(0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "the lsa packet length ." ::= { qtechOspfLsdbEntry 10 } qtechOspfSummaryLsaNetworkMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "this field is only useful when ospfLsdbType is type-3 or type-4 or type-7,it's the Lsa's network mask ." ::= { qtechOspfLsdbEntry 11 } qtechOspfSummaryLsaTos0Metric OBJECT-TYPE SYNTAX Unsigned32(0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "this field is only useful when ospfLsdbType is type-3 or type-4 or type-7,it's the Lsa's tos0 metric ." ::= { qtechOspfLsdbEntry 12 } qtechOspfNssaLsaDetailMetricType OBJECT-TYPE SYNTAX INTEGER { type1(1), type2(2) } MAX-ACCESS read-only STATUS current DESCRIPTION " this field is valid when Lsa is a type-7 LSA. The type of Nssa ernal metric. If bit E is set, the metric specified is a Type 2 external metric. This means the metric is considered larger than any link state path. If bit E is zero, the specified metric is a Type 1 external metric. This means that it is expressed in the same units as the link state metric (i.e., the same units as interface cost). " ::= { qtechOspfLsdbEntry 13 } qtechOspfNssaLsaDetailForwardAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "this field is valid when Lsa is a type-7 LSA. Data traffic for the advertised destination will be forwarded to this address. If the Forwarding address is set to 0.0.0.0, data traffic will be forwarded instead to the LSA's originator (i.e., the responsible AS boundary router) ." ::= { qtechOspfLsdbEntry 14 } qtechOspfNssaLsaDetailRouteTag OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " this field is valid when Lsa is a type-7 LSA. A 32-bit field attached to each external route. This is not used by the OSPF protocol itself. It may be used to communicate information between AS boundary routers; the precise nature of such information is outside the scope of this specification." ::= { qtechOspfLsdbEntry 15 } qtechOspfLsdbOption OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "the option field indicate which optional capabilities area associated with the LSA. " REFERENCE "OSPF Version 2, Appendix A.2, the Options Field" ::= { qtechOspfLsdbEntry 16 } -- OSPF Link State Database, External -- The Link State Database contains the Link State -- Advertisements from throughout the areas that the -- device is attached to. -- This table is identical to the OSPF LSDB Table in -- format, but contains only External Link State -- Advertisements. The purpose is to allow external -- LSAs to be displayed once for the router rather -- than once in each non-stub area. qtechOspfExtLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechOspfExtLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Process's Links State Database." REFERENCE "OSPF Version 2, Section 12 Link State Adver- tisements" ::= { qtechOspfLsaDetailInfoMibsGroup 2 } qtechOspfExtLsdbEntry OBJECT-TYPE SYNTAX QtechOspfExtLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A single Link State Advertisement." INDEX { qtechOspfExtLsdbType, qtechOspfExtLsdbLsid, qtechOspfExtLsdbRouterId } ::= { qtechOspfExtLsdbTable 1 } QtechOspfExtLsdbEntry ::= SEQUENCE{ qtechOspfExtLsdbType INTEGER, qtechOspfExtLsdbLsid IpAddress, qtechOspfExtLsdbRouterId RouterID, qtechOspfExtLsdbSequence Unsigned32, qtechOspfExtLsdbAge Unsigned32, qtechOspfExtLsdbChecksum Unsigned32, qtechOspfExtLsdbAdvertisement OCTET STRING, qtechOspfExtLsdbNetworkMask IpAddress, qtechOspfExtLsdbMetricType INTEGER, qtechOspfExtLsdbForwardAddr IpAddress, qtechOspfExtLsdbRouteTag Unsigned32, qtechOspfExtLsdbMetric INTEGER, qtechOspfExtLsdbOption Unsigned32, qtechOspfExtLsdbPacketLength Unsigned32 } qtechOspfExtLsdbType OBJECT-TYPE SYNTAX INTEGER { asExternalLink (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertise- ment format." REFERENCE "OSPF Version 2, Appendix A.4.1 The Link State Advertisement header" ::= { qtechOspfExtLsdbEntry 1 } qtechOspfExtLsdbLsid OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement." REFERENCE "OSPF Version 2, Section 12.1.4 Link State ID" ::= { qtechOspfExtLsdbEntry 2 } qtechOspfExtLsdbRouterId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The 32 bit number that uniquely identifies the originating router in the Autonomous System." REFERENCE "OSPF Version 2, Appendix C.1 Global parameters" ::= { qtechOspfExtLsdbEntry 3 } -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It qtechs with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. qtechOspfExtLsdbSequence OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement." REFERENCE "OSPF Version 2, Section 12.1.6 LS sequence number" ::= { qtechOspfExtLsdbEntry 4 } qtechOspfExtLsdbAge OBJECT-TYPE SYNTAX Unsigned32 -- Should be 0..MaxAge MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the age of the link state adver- tisement in seconds." REFERENCE "OSPF Version 2, Section 12.1.1 LS age" ::= { qtechOspfExtLsdbEntry 5 } qtechOspfExtLsdbChecksum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum." REFERENCE "OSPF Version 2, Section 12.1.7 LS checksum" ::= { qtechOspfExtLsdbEntry 6 } qtechOspfExtLsdbAdvertisement OBJECT-TYPE SYNTAX OCTET STRING (SIZE(36)) MAX-ACCESS read-only STATUS current DESCRIPTION "The entire Link State Advertisement, including its header." REFERENCE "OSPF Version 2, Section 12 Link State Adver- tisements" ::= { qtechOspfExtLsdbEntry 7 } qtechOspfExtLsdbNetworkMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address mask for the advertised destination. For example, when advertising a class A network the mask 0xff000000 would be used." ::= { qtechOspfExtLsdbEntry 8 } qtechOspfExtLsdbMetric OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION " The cost of this route. Interpretation depends on the external type indication. " ::= { qtechOspfExtLsdbEntry 9 } qtechOspfExtLsdbMetricType OBJECT-TYPE SYNTAX INTEGER { type1(1), type2(2) } MAX-ACCESS read-only STATUS current DESCRIPTION " The type of external metric. If bit E is set, the metric specified is a Type 2 external metric. This means the metric is considered larger than any link state path. If bit E is zero, the specified metric is a Type 1 external metric. This means that it is expressed in the same units as the link state metric (i.e., the same units as interface cost). " ::= { qtechOspfExtLsdbEntry 10 } qtechOspfExtLsdbForwardAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " Data traffic for the advertised destination will be forwarded to this address. If the Forwarding address is set to 0.0.0.0, data traffic will be forwarded instead to the LSA's originator (i.e., the responsible AS boundary router) ." ::= { qtechOspfExtLsdbEntry 11 } qtechOspfExtLsdbRouteTag OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "A 32-bit field attached to each external route. This is not used by the OSPF protocol itself. It may be used to communicate information between AS boundary routers; the precise nature of such information is outside the scope of this specification." ::= { qtechOspfExtLsdbEntry 12 } qtechOspfExtLsdbOption OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "the option field indicate which optional capabilities area associated with the LSA. " REFERENCE "OSPF Version 2, Appendix A.2, the Options Field" ::= { qtechOspfExtLsdbEntry 13 } qtechOspfExtLsdbPacketLength OBJECT-TYPE SYNTAX Unsigned32(0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "the lsa packet length ." ::= { qtechOspfExtLsdbEntry 14 } --Router Lsa's detail information table qtechOspfRouterLsaDetailTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechOspfRouterLsaDetailEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the router Lsa's detail Infromtion." ::= { qtechOspfLsaDetailInfoMibsGroup 3 } qtechOspfRouterLsaDetailEntry OBJECT-TYPE SYNTAX QtechOspfRouterLsaDetailEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry of this table." INDEX {qtechOspfLsdbAreaId, qtechOspfLsdbType, qtechOspfLsdbLsid, qtechOspfLsdbRouterId, qtechOspfRouterLsaDetailLinkID } ::= { qtechOspfRouterLsaDetailTable 1 } QtechOspfRouterLsaDetailEntry ::= SEQUENCE{ qtechOspfRouterLsaDetailLinkID IpAddress, qtechOspfRouterLsaDetailLinkType INTEGER, qtechOspfRouterLsaDetailLinkData IpAddress, qtechOspfRouterLsaDetailTos0Metric Unsigned32 } qtechOspfRouterLsaDetailLinkID OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "router lsa's link ID Identifies the object that this router link connects to. Value depends on the link's Type. When connecting to an object that also originates an LSA (i.e., another router or a transit network) the Link ID is equal to the neighboring LSA's Link State ID. This provides the key for looking up the neighboring LSA in the link state database during the routing table calculation. See Section 12.2 for more details. Type Link ID ________________________________________ 1 Neighboring router's Router ID 2 IP address of Designated Router 3 IP network/subnet number 4 Neighboring router's Router ID " ::= { qtechOspfRouterLsaDetailEntry 1 } qtechOspfRouterLsaDetailLinkType OBJECT-TYPE SYNTAX INTEGER{ pointtopointConnectionToAnotherRouter(1), connectionToaTransitNetwork(2), connectionToaStubNetwork(3), virtualLink(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "router lsa's link type A quick description of the router link. One of the following. Note that host routes are classified as links to stub networks with network mask of 0xffffffff." ::= { qtechOspfRouterLsaDetailEntry 2 } qtechOspfRouterLsaDetailLinkData OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " Value again depends on the link's Type field. For connections to stub networks, Link Data specifies the network's IP address mask. For unnumbered point-to-point connections, it specifies the interface's MIB-II ifIndex value. For the other link types it specifies the router interface's IP address. This latter piece of information is needed during the routing table build process, when calculating the IP address of the next hop. " ::= { qtechOspfRouterLsaDetailEntry 3 } qtechOspfRouterLsaDetailTos0Metric OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "TOS0-specific metric information." ::= { qtechOspfRouterLsaDetailEntry 4 } --NetWork Lsa's detail information table qtechOspfNetWorkLsaDetailTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechOspfNetWorkLsaDetailEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the NetWork Lsa's detail Infromtion." ::= { qtechOspfLsaDetailInfoMibsGroup 4 } qtechOspfNetWorkLsaDetailEntry OBJECT-TYPE SYNTAX QtechOspfNetWorkLsaDetailEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry of this table." INDEX {qtechOspfLsdbAreaId, qtechOspfLsdbType, qtechOspfLsdbLsid, qtechOspfLsdbRouterId, qtechOspfNetWorkLsaDetailAttachedRouter } ::= { qtechOspfNetWorkLsaDetailTable 1 } QtechOspfNetWorkLsaDetailEntry ::= SEQUENCE{ qtechOspfNetWorkLsaDetailAttachedRouter IpAddress, qtechOspfNetWorkLsaDetailNetworkMask IpAddress } qtechOspfNetWorkLsaDetailAttachedRouter OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " The Router IDs of each of the routers attached to the network. Actually, only those routers that are fully adjacent to the Designated Router are listed. The Designated Router includes itself in this list. The number of routers included can be deduced from the LSA header's length field. " ::= { qtechOspfNetWorkLsaDetailEntry 1 } qtechOspfNetWorkLsaDetailNetworkMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address mask for the network. For example, a class A network would have the mask 0xff000000." ::= { qtechOspfNetWorkLsaDetailEntry 2 } --qtech Ospf Area Lsa Database Summary Table qtechOspfAreaLsaDBSumTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechOspfAreaLsaDBSumEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Area LSA database summary Infromtion." ::= { qtechOspfLsaDetailInfoMibsGroup 5 } qtechOspfAreaLsaDBSumEntry OBJECT-TYPE SYNTAX QtechOspfAreaLsaDBSumEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry of this table." INDEX {qtechOspfAreaLsaDBSumAreaId, qtechOspfAreaLsaDBSumLsaType } ::= { qtechOspfAreaLsaDBSumTable 1 } QtechOspfAreaLsaDBSumEntry ::= SEQUENCE{ qtechOspfAreaLsaDBSumAreaId IpAddress, qtechOspfAreaLsaDBSumLsaType INTEGER, qtechOspfAreaLsaDBSumCounts Counter32, qtechOspfAreaLsaDBSumDeletes Counter32, qtechOspfAreaLsaDBSumMaxage Counter32 } qtechOspfAreaLsaDBSumAreaId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The area Id." ::= { qtechOspfAreaLsaDBSumEntry 1 } qtechOspfAreaLsaDBSumLsaType OBJECT-TYPE SYNTAX INTEGER { routerLink (1), networkLink (2), summaryLink (3), asSummaryLink (4), --asExternalLink (5), because in each area,type 5 lsa is no meaning --it's only meaning in one router -- multicastLink (6), not implement nssaExternalLink (7), subtotal(8) --subtotal is use for total counter for all type LSA in this area. } MAX-ACCESS read-only STATUS current DESCRIPTION "the entry's entry type." ::= { qtechOspfAreaLsaDBSumEntry 2 } qtechOspfAreaLsaDBSumCounts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " number os this type Lsa in this area , if this type Lsa does not exist,this field is 0." ::= { qtechOspfAreaLsaDBSumEntry 3 } qtechOspfAreaLsaDBSumDeletes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " number os this type Lsa which has been delete in this area , if this type Lsa is not been deleted,this field is 0" ::= { qtechOspfAreaLsaDBSumEntry 4 } qtechOspfAreaLsaDBSumMaxage OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " number of this type Lsa which has up to Maxage, if this type Lsa which has up to Maxage does not exist, this field is 0" ::= { qtechOspfAreaLsaDBSumEntry 5 } --qtech Ospf Lsa Database total summary table qtechOspfLsaDBSumTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechOspfLsaDBSumEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LSA database total summary infromtion in the all areas ." ::= { qtechOspfLsaDetailInfoMibsGroup 6 } qtechOspfLsaDBSumEntry OBJECT-TYPE SYNTAX QtechOspfLsaDBSumEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry of this table." INDEX { qtechOspfLsaDBSumLsaType } ::= { qtechOspfLsaDBSumTable 1 } QtechOspfLsaDBSumEntry ::= SEQUENCE{ qtechOspfLsaDBSumLsaType INTEGER, qtechOspfLsaDBSumCounts Counter32, qtechOspfLsaDBSumDeletes Counter32, qtechOspfLsaDBSumMaxage Counter32 } qtechOspfLsaDBSumLsaType OBJECT-TYPE SYNTAX INTEGER { routerLink (1), networkLink (2), summaryTotalLink (3), asSummaryTotalLink (4), asExternalLink (5), -- multicastLink (6), not implement nssaExternalLink (7), total(8) --subtotal is use for total counter for all type LSA in this router. } MAX-ACCESS read-only STATUS current DESCRIPTION "the table's entry type." ::= { qtechOspfLsaDBSumEntry 1 } qtechOspfLsaDBSumCounts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "total number of this type Lsa in all area ." ::= { qtechOspfLsaDBSumEntry 2 } qtechOspfLsaDBSumDeletes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " total number of this type Lsa deleted in all area ." ::= { qtechOspfLsaDBSumEntry 3 } qtechOspfLsaDBSumMaxage OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "total number of this type Lsa which has been up to max age in all area " ::= { qtechOspfLsaDBSumEntry 4 } -- The OSPF Neighbor Table describes all neighbors in -- the locality of the subject router. qtechOspfNeighborTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechOspfNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the neighbor detail infomation ." REFERENCE "ospfNbrTable in rfc1850" ::= { qtechOspfMIBObjects 9 } qtechOspfNeighborEntry OBJECT-TYPE SYNTAX QtechOspfNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry of this table." INDEX { qtechOspfNbrIpAddr, qtechOspfNbrAddressLessIndex } ::= { qtechOspfNeighborTable 1 } QtechOspfNeighborEntry ::= SEQUENCE{ qtechOspfNbrIpAddr IpAddress, qtechOspfNbrAddressLessIndex Unsigned32, qtechOspfNbrRtrId RouterID, qtechOspfNbrOptions Unsigned32, qtechOspfNbrPriority DesignatedRouterPriority, qtechOspfNbrState INTEGER, qtechOspfNbrEvents Counter32, qtechOspfNbrLsRetransQLen Gauge32, qtechOspfNbmaNbrStatus RowStatus, qtechOspfNbmaNbrPermanence INTEGER, qtechOspfNbrHelloSuppressed TruthValue, qtechOspfNbrDeadTimeDueIn TimeTicks, qtechOspfNbrNeighborUpTime TimeTicks, qtechOspfNbrDR IpAddress, qtechOspfNbrBDR IpAddress, qtechOspfNbrArea IpAddress, qtechOspfNbrRetransmissionNum Counter32, qtechOspfNbrIfState INTEGER } qtechOspfNbrIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address this neighbor(neighbor's interface IP address) is using in its IP Source Address. Note that, on addressless links, this will not be 0.0.0.0, but the ad- dress of another of the neighbor's interfaces." ::= { qtechOspfNeighborEntry 1 } qtechOspfNbrAddressLessIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "On an interface having an IP Address, zero. On addressless interfaces, the corresponding value of ifIndex in the Internet Standard MIB. On row creation, this can be derived from the instance." ::= { qtechOspfNeighborEntry 2 } qtechOspfNbrRtrId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "A 32-bit integer (represented as a type IpAd- dress) uniquely identifying the neighboring router in the Autonomous System." ::= { qtechOspfNeighborEntry 3 } qtechOspfNbrOptions OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "A Bit Mask corresponding to the neighbor's op- tions field. Bit 0, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric. Bit 1, if set, indicates that the associated area accepts and operates on external informa- tion; if zero, it is a stub area. Bit 2, if set, indicates that the system is ca- pable of routing IP Multicast datagrams; i.e., that it implements the Multicast Extensions to OSPF. Bit 3, if set, indicates that the associated area is an NSSA. These areas are capable of carrying type 7 external advertisements, which are translated into type 5 external advertise- ments at NSSA borders." REFERENCE "OSPF Version 2, Section 12.1.2 Options" ::= { qtechOspfNeighborEntry 4 } qtechOspfNbrPriority OBJECT-TYPE SYNTAX DesignatedRouterPriority MAX-ACCESS read-only STATUS current DESCRIPTION "The priority of this neighbor in the designat- ed router election algorithm. The value 0 sig- nifies that the neighbor is not eligible to be- come the designated router on this particular network." ::= { qtechOspfNeighborEntry 5 } qtechOspfNbrState OBJECT-TYPE SYNTAX INTEGER { down (1), attempt (2), init (3), twoWay (4), exchangeQtech (5), exchange (6), loading (7), full (8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The State of the relationship with this Neigh- bor." REFERENCE "OSPF Version 2, Section 10.1 Neighbor States" ::= { qtechOspfNeighborEntry 6 } qtechOspfNbrEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this neighbor relationship has changed state, or an error has occurred." ::= { qtechOspfNeighborEntry 7 } qtechOspfNbrLsRetransQLen OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current length of the retransmission queue." ::= { qtechOspfNeighborEntry 8 } qtechOspfNbmaNbrStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-only STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { qtechOspfNeighborEntry 9 } qtechOspfNbmaNbrPermanence OBJECT-TYPE SYNTAX INTEGER { dynamic (1), -- learned through protocol permanent (2) -- configured address } MAX-ACCESS read-only STATUS current DESCRIPTION "This variable displays the status of the en- try. 'dynamic' and 'permanent' refer to how the neighbor became known." ::= { qtechOspfNeighborEntry 10 } qtechOspfNbrHelloSuppressed OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether Hellos are being suppressed to the neighbor" ::= { qtechOspfNeighborEntry 11 } qtechOspfNbrDeadTimeDueIn OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "if in this interval ,hello packet is not been received , the neighbor is recognized dead.if received,it will recovery the dead time which has been setted." ::= { qtechOspfNeighborEntry 12 } qtechOspfNbrNeighborUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "the time that the neighbor has been up." ::= { qtechOspfNeighborEntry 13 } qtechOspfNbrDR OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "the Designated Router of this neighbor." ::= { qtechOspfNeighborEntry 14 } qtechOspfNbrBDR OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "the Backup Designated Router of this neighbor." ::= { qtechOspfNeighborEntry 15 } qtechOspfNbrArea OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "the area where the neighbor is in." ::= { qtechOspfNeighborEntry 16 } qtechOspfNbrRetransmissionNum OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "the Retransmission times." ::= { qtechOspfNeighborEntry 17 } qtechOspfNbrIfState OBJECT-TYPE SYNTAX INTEGER { other(0), designatedRouter (1), backupDesignatedRouter (2), otherDesignatedRouter (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The neighbor's interface State which connected to local router." ::= { qtechOspfNeighborEntry 18 } --OSPF border routing information qtechOspfRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechOspfRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entity's OSPF border routing table." ::= { qtechOspfMIBObjects 10 } qtechOspfRouteEntry OBJECT-TYPE SYNTAX QtechOspfRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A route to a destination." INDEX { qtechOspfRouteDest, qtechOspfRouteArea, qtechOspfRouteNextHop } ::= { qtechOspfRouteTable 1 } QtechOspfRouteEntry ::= SEQUENCE { qtechOspfRouteDest IpAddress, qtechOspfRouteArea IpAddress, qtechOspfRouteNextHop IpAddress, qtechOspfRouteCost Unsigned32, qtechOspfRouteType INTEGER, qtechOspfRouteDRType INTEGER, qtechOspfRouteSpfNo Counter32 } qtechOspfRouteDest OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Router ID of the destination." ::= { qtechOspfRouteEntry 1 } qtechOspfRouteArea OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The area ID of the area from which this route is learned." ::= { qtechOspfRouteEntry 2 } qtechOspfRouteNextHop OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Next hop toward the destination." ::= { qtechOspfRouteEntry 3 } qtechOspfRouteCost OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION " Cost of using this route." ::= { qtechOspfRouteEntry 4 } qtechOspfRouteDRType OBJECT-TYPE SYNTAX INTEGER { abr(1), asbr(2), both(3) --abr and asbr } MAX-ACCESS read-only STATUS current DESCRIPTION "The router type of the destination; it is either an ABR or ASBR or both." ::= { qtechOspfRouteEntry 5 } qtechOspfRouteType OBJECT-TYPE SYNTAX INTEGER { intral-area-route(1), inter-area-route(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "this field indicate this route is an intral area route or inter area route." ::= { qtechOspfRouteEntry 6 } qtechOspfRouteSpfNo OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " The internal number of the shortest path first (SPF) calculation that installs this route." ::= { qtechOspfRouteEntry 7 } -- conformance information qtechOspfMIBConformance OBJECT IDENTIFIER ::= { qtechOspfMIB 2 } qtechOspfMIBCompliances OBJECT IDENTIFIER ::= { qtechOspfMIBConformance 1 } qtechOspfMIBGroups OBJECT IDENTIFIER ::= { qtechOspfMIBConformance 2 } -- compliance statements qtechOspfMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the Qtech OSPF MIB" MODULE -- this module MANDATORY-GROUPS { qtechOspfBaseMIBGroup, qtechOspfAreaMIBGroup, qtechOspfLsaMIBGroup, qtechOspfIfMIBGroup, qtechOspfVirtMIBGroup, qtechOspfNeighborMIBGroup, qtechOspfRouteInfoMIBGroup } ::= { qtechOspfMIBCompliances 1 } -- units of conformance qtechOspfBaseMIBGroup OBJECT-GROUP OBJECTS { qtechOspfMiniLsaInterval , qtechOspfMiniLsaArrival , qtechOspfAreasNum , qtechOspfNormalAreasNum , qtechOspfStubAreasNum , qtechOspfNssaAreasNum , qtechOspfSpfDelay , qtechOspfSpfHoldTime , qtechOspfAutoCostRefBandWidthRef , qtechOspfLsaGroupPacing , qtechOspfInterDistance , qtechOspfIntraDistance , qtechOspfExternDistance , qtechOspfLogAdjChangeNotify , qtechOspfPassiveStatus , qtechOspfRFC1583Compatibility , qtechOspfRouteRedisDefMetricVal } STATUS current DESCRIPTION "A collection of general objects providing OSPF managment." ::= { qtechOspfMIBGroups 1 } qtechOspfAreaMIBGroup OBJECT-GROUP OBJECTS { qtechOspfAreaId, qtechOspfAuthType, qtechOspfImportAsExtern, qtechOspfSpfRuns, qtechOspfAreaBdrRtrCount, qtechOspfAsBdrRtrCount, qtechOspfAreaLsaCount, qtechOspfAreaLsaCksumSum, qtechOspfAreaSummary, qtechOspfAreaStatus, qtechOspfAreaInterfaceNum, qtechOspfAreaNssaIsRedistribution, qtechOspfAreaNssaIsDefInfoOriginate, qtechOspfNetWorkAreaID, qtechOspfNetWorkAddress, qtechOspfNetWorkMask, qtechOspfNetWorkStatus } STATUS current DESCRIPTION "A collection of area objects providing OSPF managment." ::= { qtechOspfMIBGroups 2 } qtechOspfLsaMIBGroup OBJECT-GROUP OBJECTS { qtechOspfLsdbAreaId, qtechOspfLsdbType, qtechOspfLsdbLsid, qtechOspfLsdbRouterId, qtechOspfLsdbSequence, qtechOspfLsdbAge, qtechOspfLsdbChecksum, qtechOspfLsdbAdvertisement, qtechOspfLsdbLinkNum, qtechOspfLsdbPacketLength, qtechOspfSummaryLsaNetworkMask, qtechOspfSummaryLsaTos0Metric, qtechOspfNssaLsaDetailMetricType, qtechOspfNssaLsaDetailForwardAddr , qtechOspfNssaLsaDetailRouteTag , qtechOspfLsdbOption, qtechOspfExtLsdbType, qtechOspfExtLsdbLsid, qtechOspfExtLsdbRouterId, qtechOspfExtLsdbSequence, qtechOspfExtLsdbAge, qtechOspfExtLsdbChecksum, qtechOspfExtLsdbAdvertisement, qtechOspfExtLsdbNetworkMask, qtechOspfExtLsdbMetricType, qtechOspfExtLsdbForwardAddr, qtechOspfExtLsdbRouteTag, qtechOspfExtLsdbMetric, qtechOspfExtLsdbOption, qtechOspfExtLsdbPacketLength, qtechOspfRouterLsaDetailLinkID, qtechOspfRouterLsaDetailLinkType, qtechOspfRouterLsaDetailLinkData, qtechOspfRouterLsaDetailTos0Metric, qtechOspfNetWorkLsaDetailAttachedRouter, qtechOspfNetWorkLsaDetailNetworkMask, qtechOspfAreaLsaDBSumAreaId, qtechOspfAreaLsaDBSumLsaType, qtechOspfAreaLsaDBSumCounts , qtechOspfAreaLsaDBSumDeletes, qtechOspfAreaLsaDBSumMaxage, qtechOspfLsaDBSumLsaType, qtechOspfLsaDBSumCounts, qtechOspfLsaDBSumDeletes, qtechOspfLsaDBSumMaxage } STATUS current DESCRIPTION "A collection of OSPF Link State Database objects providing OSPF managment." ::= { qtechOspfMIBGroups 3 } qtechOspfIfMIBGroup OBJECT-GROUP OBJECTS { qtechOspfIfIpAddress, qtechOspfAddressLessIf, qtechOspfIfAreaId, qtechOspfIfType, qtechOspfIfAdminStat, qtechOspfIfRtrPriority, qtechOspfIfTransitDelay, qtechOspfIfRetransInterval, qtechOspfIfHelloInterval, qtechOspfIfRtrDeadInterval, qtechOspfIfPollInterval, qtechOspfIfState, qtechOspfIfDesignatedRouter, qtechOspfIfBackupDesignatedRouter, qtechOspfIfEvents, qtechOspfIfAuthType, qtechOspfIfAuthKey, qtechOspfIfStatus, qtechOspfIfMulticastForwarding, qtechOspfIfDemand, qtechOspfIfDatabaseFilterAllOut, qtechOspfIfDesignateRouterId , qtechOspfIfBackupDesignateRouterId , -- qtechOspfIfMd5AuthKeyId, qtechOspfIfWaitInternal, qtechOspfIfPassiveStatus, qtechOspfIfCurrentUsedMd5AuthKeyId, qtechOspfIfMd5AuthKeyIf, qtechOspfIfMd5AuthKeyId, qtechOspfIfMd5AuthKey, qtechOspfIfMd5AuthKeySt } STATUS current DESCRIPTION "A collection of OSPF interface managment." ::= { qtechOspfMIBGroups 4 } qtechOspfVirtMIBGroup OBJECT-GROUP OBJECTS { qtechOspfVirtIfAreaId, qtechOspfVirtIfNeighbor, qtechOspfVirtIfTransitDelay, qtechOspfVirtIfRetransInterval, qtechOspfVirtIfHelloInterval, qtechOspfVirtIfRtrDeadInterval, qtechOspfVirtIfState, qtechOspfVirtIfEvents, qtechOspfVirtIfAuthType, qtechOspfVirtIfAuthKey, qtechOspfVirtIfStatus, qtechOspfVirtCost, qtechOspfVirtNativeIfIndex, qtechOspfVirtLinkState, qtechOspfVirtHelloDueIn, qtechOspfVirtIfMd5AuthKeyAreaId, qtechOspfVirtIfMd5AuthKeyNeighbor, qtechOspfVirtIfMd5AuthKeyId, qtechOspfVirtIfMd5AuthKey, qtechOspfVirtIfMd5AuthKeySt, qtechOspfVirtCurrentUsedMd5AuthKeyId } STATUS current DESCRIPTION "A collection of OSPF Virtual Link managment." ::= { qtechOspfMIBGroups 5 } qtechOspfNeighborMIBGroup OBJECT-GROUP OBJECTS { qtechOspfNbrIpAddr, qtechOspfNbrAddressLessIndex, qtechOspfNbrRtrId, qtechOspfNbrOptions, qtechOspfNbrPriority, qtechOspfNbrState, qtechOspfNbrEvents, qtechOspfNbrLsRetransQLen, qtechOspfNbmaNbrStatus, qtechOspfNbmaNbrPermanence, qtechOspfNbrHelloSuppressed, qtechOspfNbrDeadTimeDueIn, qtechOspfNbrNeighborUpTime, qtechOspfNbrDR, qtechOspfNbrBDR, qtechOspfNbrArea, qtechOspfNbrRetransmissionNum } STATUS current DESCRIPTION "A collection of OSPF Neighbor information." ::= { qtechOspfMIBGroups 6 } qtechOspfRouteInfoMIBGroup OBJECT-GROUP OBJECTS { qtechOspfRouteType, qtechOspfRouteDest, qtechOspfRouteNextHop, qtechOspfRouteCost, qtechOspfRouteDRType, qtechOspfRouteArea, qtechOspfRouteSpfNo } STATUS current DESCRIPTION "A collection of OSPF route information." ::= { qtechOspfMIBGroups 7 } -- ------------------------------------------------------------- -- Compliance statements -- ------------------------------------------------------------- ospfMIBConformance OBJECT IDENTIFIER ::= { qtechOspfMIB 3 } ospfMIBCompliances OBJECT IDENTIFIER ::= { ospfMIBConformance 1 } ospfExternCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for device support of OSPF services." MODULE -- OBJECT ospfASBdrRtrStatus -- MIN-ACCESS read-only -- DESCRIPTION "Write access is not required." -- -- OBJECT ospfTOSSupport -- MIN-ACCESS read-only -- DESCRIPTION "Write access is not required." -- -- OBJECT ospfExtLsdbLimit -- MIN-ACCESS read-only -- DESCRIPTION "Write access is not required." -- -- OBJECT ospfMulticastExtensions -- MIN-ACCESS read-only -- DESCRIPTION "Write access is not required." -- -- OBJECT ospfExitOverflowInterval -- MIN-ACCESS read-only -- DESCRIPTION "Write access is not required." -- -- OBJECT ospfDemandExtensions -- MIN-ACCESS read-only -- DESCRIPTION "Write access is not required." -- -- OBJECT ospfIfAreaId -- MIN-ACCESS read-only -- DESCRIPTION "Write access is not required." -- -- OBJECT ospfIfStatus -- MIN-ACCESS read-only -- DESCRIPTION "Create access is not required." -- -- -- OBJECT ospfStubMetric -- MIN-ACCESS read-write -- DESCRIPTION "Create access is not required." -- -- OBJECT ospfStubStatus -- MIN-ACCESS read-only -- DESCRIPTION "Write access is not required." -- -- OBJECT ospfStubMetricType -- MIN-ACCESS read-write -- DESCRIPTION "Create access is not required." -- -- OBJECT ospfIfAdminStat -- MIN-ACCESS read-only -- DESCRIPTION "Write access is not required." -- -- OBJECT ospfNbmaNbrStatus -- MIN-ACCESS read-only -- DESCRIPTION "Read-create access is not required." -- -- OBJECT ospfNbrPriority -- MIN-ACCESS read-only -- DESCRIPTION "Read-create access is not required." -- -- OBJECT ospfIfPollInterval -- MIN-ACCESS read-only -- DESCRIPTION "Read-create access is not required." -- -- OBJECT ospfIfTransitDelay -- SYNTAX Unsigned32 (1..65535) -- DESCRIPTION "Range of value is changed." -- -- OBJECT ospfIfRetransInterval -- SYNTAX Unsigned32 (1..65535) -- DESCRIPTION "Range of value is changed." -- -- OBJECT ospfVirtIfTransitDelay -- SYNTAX Unsigned32 (1..65535) -- DESCRIPTION "Range of value is changed." -- -- OBJECT ospfIfType -- SYNTAX INTEGER { -- broadcast (1), -- nbma (2), -- pointToPoint (3), -- pointToMultipoint (5), -- loopback(6) -- } -- DESCRIPTION "add type 'loopback'." -- -- OBJECT ospfVirtIfRetransInterval -- SYNTAX Unsigned32 (1..65535) -- DESCRIPTION "Range of value is changed." OBJECT qtechOspfVirtIfRtrDeadInterval SYNTAX PositiveInteger DESCRIPTION "default value change from 60 to 40." ::= { ospfMIBCompliances 1 } END