-- ******************************************************************* -- Qtech-FRAME-RELAY-MIB.mib -- Qtech Frame Relay MIB file, providing Frame Relay specific -- information that are either excluded by RFC 1315 (FR DTE MIB) -- or specific to Qtech products. -- -- May 2009, juncheng hong -- -- Copyright (c) 2009 by Qtech Networks Co.,Ltd. -- All rights reserved. -- -- ******************************************************************* -- Note: -- Until future change, it is no intention for this MIB to cover -- every Frame Relay related feature, configuration statement, or -- exec command display. The focus is to provide key information -- that are unavailable in any of the existing MIB's, but are -- currently available through the Frame Relay show commands and/or -- configuration displays. QTECH-FRAME-RELAY-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Integer32, IpAddress FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION, DisplayString, TruthValue FROM SNMPv2-TC qtechMgmt FROM QTECH-SMI InterfaceIndex, ifIndex FROM IF-MIB frDlcmiEntry, frCircuitEntry, frCircuitIfIndex, frCircuitDlci FROM FRAME-RELAY-DTE-MIB; -- All table indicies in this MIB that involve interface index and -- DLCI are derived from frCircuitIfIndex and frCircuitDlci -- respectively from RFC 1315. qtechFrameRelayMIB MODULE-IDENTITY LAST-UPDATED "200010130000Z" ORGANIZATION "Qtech Networks Co.,Ltd." CONTACT-INFO " Tel: 4008-111-000 E-mail: service@qtech.com.cn" DESCRIPTION "Qtech Frame Relay MIB" REVISION "200010130000Z" DESCRIPTION "(1) Added objects of FR Switching, FR Fragmentation and FR/ATM Interworking. (2) Objects for per PVC I/O rate is added to cfrExtCircuitTable" REVISION "200005220000Z" DESCRIPTION "(1) Added ELMI subgroup for ELMI objects." REVISION "200005160000Z" DESCRIPTION "(1) Added Traffic Shaping parameter objects to qtechfrExtCircuitTable. (2) Deprecated qtechfrSvcMinThruputOut and qtechfrSvcMinThruputIn. Added qtechfrExtCircuitMinThruputOut and qtechfrExtCircuitMinThruputIn in qtechfrExtCircuitTable inorder to make them applicable to both PVC/SVC. (3) Added qtechfrExtCircuitBandwidth object to qtechfrExtCircuitTable." REVISION "200905180000Z" DESCRIPTION "(1) add an integer value for qtechfrMapPayloadCompressType; (2) reword the Description statements for { qtechfrMapPayloadCompressType, qtechfrExtCircuitUncompressIns, qtechfrExtCircuitUncompressOuts } so that they are not limited to software compression." REVISION "9908210000Z" DESCRIPTION "(1) Added qtechfrExtCircuitUncompressOuts and qtechfrExtCircuitUncompressIns to the circuit subgroup; (2) Added qtechfrMapRtpHdrCompress and qtechfrMapPayloadCompressType to the mapping subgroup; (3) qtechfrMapPayloadCompress becomes deprecated, obsoleted by qtechfrMapPayloadCompressType; (4) frCircuitSentOctets and frCircuitReceivedOctets per RFC1315 will reflect the number of bytes in Frame Relay frames sent to and received from the physical layer. Same effect is applied to ifOutOctets and ifInOctets as well when ifIndex refers to a Frame Relay subinterface." REVISION "9608150000Z" DESCRIPTION "Initial version of this MIB module." ::= { qtechMgmt 50 } qtechFrMIBObjects OBJECT IDENTIFIER ::= { qtechFrameRelayMIB 1 } -- Subgroups: -- The objects include four subgroups on the topics of -- o LMI (Local Management Interface, see ANSI T1.617 Annex D and -- the Frame Relay Specification with Extensions by DEC, -- NT, StrataCom, and Qtech.), -- o Virtual circuits, -- o Circuit mapping information, -- o SVC (switched virtual circuits, see CCITT/ITU Q.933 and -- Q.922.), -- o ELMI (Enhanced Link Management Interface) objects, -- o Fragmentation objects, -- o Frame Relay/ATM Network Interworking objects, -- o Frame Relay/ATM PVC Service Interworking objects, and -- o Frame Relay Switching objects. qtechfrLmiObjs OBJECT IDENTIFIER ::= { qtechFrMIBObjects 1 } qtechfrCircuitObjs OBJECT IDENTIFIER ::= { qtechFrMIBObjects 2 } qtechfrMapObjs OBJECT IDENTIFIER ::= { qtechFrMIBObjects 3 } qtechfrSvcObjs OBJECT IDENTIFIER ::= { qtechFrMIBObjects 4 } qtechfrElmiObjs OBJECT IDENTIFIER ::= { qtechFrMIBObjects 5 } qtechfrFragObjs OBJECT IDENTIFIER ::= { qtechFrMIBObjects 6 } qtechfrConnectionObjs OBJECT IDENTIFIER ::= { qtechFrMIBObjects 7 } DlciNumber ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Numerical format of Data Link Connection Identifier (DLCI) in decimal, identical to the 'DLCI' as INTEGER of 0..DLCINumber in RFC1315. The maximum value depends on Frame Relay implementation, which is currently set to be 1023 for 2-octet address format per UNI Implementation Agreement FRF.1." SYNTAX INTEGER (0..1023) QtechfrMapProtocols ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Qtech link types (network protocols) that run over Frame Relay. Associated values, except for wildcard, match assigned values of internal software respectively." SYNTAX INTEGER { arp(1), serialArp(6), ip(7), xns(10), novell(11), apollo(12), vines(13), appletalk(16), ieeeSpanning(18), decnet(22), clns(25), rsrb(37), bridge(38), stun(39), frArp(40), uncompressedTcp(47), compressedTcp(48), llc2(49), frSwitch(53), dlsw(63), nhrp(74), compressedRtp(83), wildcard(999) -- either means no applicable type for -- the circuit or means point-to-point } -- LMI sub-group { qtechfrLmiTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechfrLmiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of Frame Relay LMI information that are either supplemental to the frDlcmiTable of RFC 1315 or specific to Qtech's implementation." REFERENCE "American National Standard T1.617-1991, Annex D" ::= { qtechfrLmiObjs 1 } qtechfrLmiEntry OBJECT-TYPE SYNTAX QtechfrLmiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry of the table contains information of Frame Relay LMI over one physical interface. They are mostly FR generic and some Qtech specific." AUGMENTS { frDlcmiEntry } ::= { qtechfrLmiTable 1 } QtechfrLmiEntry ::= SEQUENCE { qtechfrLmiLinkstatus INTEGER, qtechfrLmiLinkType INTEGER, qtechfrLmiEnquiryIns Counter32, qtechfrLmiEnquiryOuts Counter32, qtechfrLmiStatusIns Counter32, qtechfrLmiStatusOuts Counter32, qtechfrLmiUpdateStatusIns Counter32, qtechfrLmiUpdateStatusOuts Counter32, qtechfrLmiStatusTimeouts Counter32, qtechfrLmiStatusEnqTimeouts Counter32, qtechfrLmiN392Dce INTEGER, qtechfrLmiN393Dce INTEGER, qtechfrLmiT392Dce INTEGER } -- Note: for LMI type, i.e. ANSI or cisco, see frDlcmiState -- of RFC 1315. Also, for LMI parameters for DTE not listed here, -- e.g. T391, N391, N392, and N393, see RFC 1315. -- -- Although based on the current logic the value for -- cfrLmiDLstatus is equivalent to ifOperStatus, the object -- remains herein for future possible development change. qtechfrLmiLinkstatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Data link status via LMI." ::= { qtechfrLmiEntry 1 } qtechfrLmiLinkType OBJECT-TYPE SYNTAX INTEGER { dte(1), dce(2), nni(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Frame Relay link type." ::= { qtechfrLmiEntry 2 } qtechfrLmiEnquiryIns OBJECT-TYPE SYNTAX Counter32 UNITS "messages" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Status Enquiry messages received." ::= { qtechfrLmiEntry 3 } qtechfrLmiEnquiryOuts OBJECT-TYPE SYNTAX Counter32 UNITS "messages" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Status Enquiry messages sent." ::= { qtechfrLmiEntry 4 } qtechfrLmiStatusIns OBJECT-TYPE SYNTAX Counter32 UNITS "messages" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Status messages received." ::= { qtechfrLmiEntry 5 } qtechfrLmiStatusOuts OBJECT-TYPE SYNTAX Counter32 UNITS "messages" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Status messages sent." ::= { qtechfrLmiEntry 6 } qtechfrLmiUpdateStatusIns OBJECT-TYPE SYNTAX Counter32 UNITS "messages" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Update Status messages received." ::= { qtechfrLmiEntry 7 } qtechfrLmiUpdateStatusOuts OBJECT-TYPE SYNTAX Counter32 UNITS "messages" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Update Status messages sent" ::= { qtechfrLmiEntry 8 } qtechfrLmiStatusTimeouts OBJECT-TYPE SYNTAX Counter32 UNITS "times" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times when timeout occurred on waiting for Status message" ::= { qtechfrLmiEntry 9 } qtechfrLmiStatusEnqTimeouts OBJECT-TYPE SYNTAX Counter32 UNITS "times" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times when timeout occurred on waiting for Status Enquiry message" ::= { qtechfrLmiEntry 10 } qtechfrLmiN392Dce OBJECT-TYPE SYNTAX INTEGER (0..10) MAX-ACCESS read-only STATUS current DESCRIPTION "LMI error threshold for DCE interface. For DTE, value becomes 0." ::= { qtechfrLmiEntry 11 } qtechfrLmiN393Dce OBJECT-TYPE SYNTAX INTEGER (0..10) MAX-ACCESS read-only STATUS current DESCRIPTION "LMI monitored event count for DCE interface. For DTE, value becomes zero (0)." ::= { qtechfrLmiEntry 12 } qtechfrLmiT392Dce OBJECT-TYPE SYNTAX INTEGER (0..30) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "DCE polling verification timer for DCE interface For DTE, the value becomes zero (0)." ::= { qtechfrLmiEntry 13 } -- end LMI subgroup } -- Circut sub-group { qtechfrCircuitTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechfrCircuitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive and statistics information that are generic to Frame Relay virtual circuits." ::= { qtechfrCircuitObjs 1 } qtechfrCircuitEntry OBJECT-TYPE SYNTAX QtechfrCircuitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry of the table contains information of a circuit that are not included in frCircuitTable of RFC1315 but are generic to Frame Relay." AUGMENTS { frCircuitEntry } -- indexed by { frCircuitIfIndex, frCircuitDlci } ::= { qtechfrCircuitTable 1 } QtechfrCircuitEntry ::= SEQUENCE { qtechfrCircuitDEins Counter32, qtechfrCircuitDEouts Counter32, qtechfrCircuitDropPktsOuts Counter32, qtechfrCircuitType INTEGER } qtechfrCircuitDEins OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets received with the Discarded Eligibility indictor (the DE bit) set." ::= { qtechfrCircuitEntry 1 } qtechfrCircuitDEouts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets transmitted with DE bit set." ::= { qtechfrCircuitEntry 2 } qtechfrCircuitDropPktsOuts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of discarded packets that were to be sent." ::= { qtechfrCircuitEntry 3 } qtechfrCircuitType OBJECT-TYPE SYNTAX INTEGER { pvc(1), -- permanent virtual circuit svc(2) -- switched virtual circuit } MAX-ACCESS read-only STATUS current DESCRIPTION "Basic circuit type" ::= { qtechfrCircuitEntry 4 } -- Qtech specific circuit information: qtechfrExtCircuitTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechfrExtCircuitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of Qtech implementation specific FR circuit information. This is a Qtech extension for the frCircuitTable of RFC 1315." ::= { qtechfrCircuitObjs 2 } qtechfrExtCircuitEntry OBJECT-TYPE SYNTAX QtechfrExtCircuitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry of the table contains information of a Frame Relay virtual circuit that are specific to Qtech implementation." AUGMENTS { frCircuitEntry } -- indexed by { frCircuitIfIndex, frCircuitDlci } ::= { qtechfrExtCircuitTable 1 } QtechfrExtCircuitEntry ::= SEQUENCE { qtechfrExtCircuitIfName DisplayString, qtechfrExtCircuitIfType INTEGER, qtechfrExtCircuitSubifIndex InterfaceIndex, qtechfrExtCircuitMapStatus INTEGER, qtechfrExtCircuitCreateType INTEGER, qtechfrExtCircuitMulticast TruthValue, qtechfrExtCircuitRoutedDlci DlciNumber, qtechfrExtCircuitRoutedIf InterfaceIndex, qtechfrExtCircuitUncompressIns Counter32, qtechfrExtCircuitUncompressOuts Counter32, qtechfrExtCircuitFECNOuts Counter32, qtechfrExtCircuitBECNOuts Counter32, qtechfrExtCircuitMinThruputOut Integer32, qtechfrExtCircuitMinThruputIn Integer32, qtechfrExtCircuitBcastPktOuts Counter32, qtechfrExtCircuitBcastByteOuts Counter32, qtechfrExtCircuitBandwidth Integer32, qtechfrExtCircuitShapeByteLimit Integer32, qtechfrExtCircuitShapeInterval Integer32, qtechfrExtCircuitShapeByteIncrement Integer32, qtechfrExtCircuitShapePkts Counter32, qtechfrExtCircuitShapeBytes Counter32, qtechfrExtCircuitShapePktsDelay Counter32, qtechfrExtCircuitShapeBytesDelay Counter32, qtechfrExtCircuitShapeActive TruthValue, qtechfrExtCircuitShapeAdapting INTEGER, qtechfrExtCircuitTxDataRate INTEGER, qtechfrExtCircuitTxPktRate INTEGER, qtechfrExtCircuitRcvDataRate INTEGER, qtechfrExtCircuitRcvPktRate INTEGER } qtechfrExtCircuitIfName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The textual name of the main interface or the subinterface that this DLCI is associated with. This is the same name string of an interface used in the configuration and all console displays, such as 'serial 0', 'serial 3/0.3', etc." ::= { qtechfrExtCircuitEntry 1 } qtechfrExtCircuitIfType OBJECT-TYPE SYNTAX INTEGER { mainInterface(1), pointToPoint(2), -- subinterface multipoint(3) -- subinterface } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of the subinterface this DLCI is associated with, if configured." ::= { qtechfrExtCircuitEntry 2 } qtechfrExtCircuitSubifIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "For value greater than zero (0), it indicates the network management interface index for the subinterface associated with this DLCI. Value 0 means the DLCI is not associated with any subinterface." ::= { qtechfrExtCircuitEntry 3 } qtechfrExtCircuitMapStatus OBJECT-TYPE SYNTAX INTEGER (0..2047) MAX-ACCESS read-only STATUS current DESCRIPTION "The mapping protocols (internally considered as the 'link type') applied on this circuit. The value ranges from 0 to 2047. For point-to-point DLCI, the value stays zero. Otherwise, the value is a sum. It initially takes the value zero, then, for each type of Protocol, 2 raised to a power is added to the sum. The following table presents respective power and equivalent value for each applicable type: Protocol Power Value -------- ----- ----- IP 0 1 IPX 1 2 Appletalk 2 4 XNS 3 8 VINES 4 16 DECnet 5 32 CLNS 6 64 Bridging 7 128 RSRB 8 256 STUN 9 512 LLC2 10 1024 For example, value 3 means the circuit's mapping protocols include IP and IPX. (3 = 2**1 + 2**0, where 0 corresponds to IP and 1 to IPX.) Value 0 means there is currently no mapping protocol for the circuit. See qtechfrMapTable for more mapping information." ::= { qtechfrExtCircuitEntry 4 } qtechfrExtCircuitCreateType OBJECT-TYPE SYNTAX INTEGER { dynamic(1), -- PVC established through LMI -- or an SVC established through -- SVC signalling static(2) -- circuit was configured } MAX-ACCESS read-only STATUS current DESCRIPTION "Identify the last source of the circuit's creation." ::= { qtechfrExtCircuitEntry 5 } qtechfrExtCircuitMulticast OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate if this DLCI is a multicast DLCI." ::= { qtechfrExtCircuitEntry 6 } qtechfrExtCircuitRoutedDlci OBJECT-TYPE SYNTAX DlciNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The routed DLCI to pair up with this DLCI for switching function. NOTE: Value zero (0) indicates that there is no such routed DLCI corresponding to this DLCI." ::= { qtechfrExtCircuitEntry 7 } qtechfrExtCircuitRoutedIf OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The interface for the routed DLCI that pairs up with this DLCI for switching. Value greater than 0 is the InterfaceIndex for that interface. Value zero (0) indicates that there is no such routed DLCI corresponding to this DLCI." ::= { qtechfrExtCircuitEntry 8 } qtechfrExtCircuitUncompressIns OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of inbound octets of the data packets, accounted at Frame Relay level after FRF.9 payload decompression is applied. In the case of non-FRF.9, this value could be identical to frCircuitReceivedOctets, unless otherwise noted." ::= { qtechfrExtCircuitEntry 9 } qtechfrExtCircuitUncompressOuts OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of outbound octets of the data packets, accounted at Frame Relay level before FRF.9 payload compression is applied. In the case of non-FRF.9, this value could be identical to frCircuitSentOctets, unless otherwise noted." ::= { qtechfrExtCircuitEntry 10 } qtechfrExtCircuitFECNOuts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of frames sent out to the network indicating forward congestion." ::= { qtechfrExtCircuitEntry 11 } qtechfrExtCircuitBECNOuts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of frames sent out to the network indicating backward congestion." ::= { qtechfrExtCircuitEntry 12 } qtechfrExtCircuitMinThruputOut OBJECT-TYPE SYNTAX Integer32 (9600..1544000) UNITS "bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "Circuit's outgoing minimal Throughput based on configuration." ::= { qtechfrExtCircuitEntry 13 } qtechfrExtCircuitMinThruputIn OBJECT-TYPE SYNTAX Integer32 (9600..1544000) UNITS "bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "Circuit's incoming minimal Throughput based on configuration." ::= { qtechfrExtCircuitEntry 14 } qtechfrExtCircuitBcastPktOuts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of broadcast packets sent out to the network." ::= { qtechfrExtCircuitEntry 15 } qtechfrExtCircuitBcastByteOuts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes sent out to the network in broadcast packets." ::= { qtechfrExtCircuitEntry 16 } qtechfrExtCircuitBandwidth OBJECT-TYPE SYNTAX Integer32 (0..16777215) UNITS "bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "Bandwidth of the virtual circuit, acquired from Qtech typed LMI Full Status message." ::= { qtechfrExtCircuitEntry 17 } qtechfrExtCircuitShapeByteLimit OBJECT-TYPE SYNTAX Integer32 (125..2147483647) UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum number of tokens a token bucket can hold in any time interval in case of traffic shaping." ::= { qtechfrExtCircuitEntry 18 } qtechfrExtCircuitShapeInterval OBJECT-TYPE SYNTAX Integer32 (10..125) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Committed rate measurement interval." ::= { qtechfrExtCircuitEntry 19 } qtechfrExtCircuitShapeByteIncrement OBJECT-TYPE SYNTAX Integer32 (125..2147483647) UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of tokens added into the token bucket per time interval in case of traffic shaping." ::= { qtechfrExtCircuitEntry 20 } qtechfrExtCircuitShapePkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of packets that went through traffic shaping." ::= { qtechfrExtCircuitEntry 21 } qtechfrExtCircuitShapeBytes OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes that went through traffic shaping." ::= { qtechfrExtCircuitEntry 22 } qtechfrExtCircuitShapePktsDelay OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of packets that were delayed by the traffic shaper." ::= { qtechfrExtCircuitEntry 23 } qtechfrExtCircuitShapeBytesDelay OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes that were delayed by the traffic shaper." ::= { qtechfrExtCircuitEntry 24 } qtechfrExtCircuitShapeActive OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Shows whether shaping is active or not." ::= { qtechfrExtCircuitEntry 25 } qtechfrExtCircuitShapeAdapting OBJECT-TYPE SYNTAX INTEGER { none(1), becn(2), foreSight(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of Adaptive Shaping configured. none(1) - No adaptive shaping configured becn(2) - Backward Explicit Congestion Notification foreSight(3) - ForeSight is the network traffic control software used in Qtech WAN switches" ::= { qtechfrExtCircuitEntry 26 } qtechfrExtCircuitTxDataRate OBJECT-TYPE SYNTAX INTEGER (1..45000000) MAX-ACCESS read-only STATUS current DESCRIPTION "The average rate (bytes/second) at which data is transmitted in this circuit. " ::= { qtechfrExtCircuitEntry 27 } qtechfrExtCircuitTxPktRate OBJECT-TYPE SYNTAX INTEGER (1..45000000) MAX-ACCESS read-only STATUS current DESCRIPTION "The average number of packets sent in a second in this circuit." ::= { qtechfrExtCircuitEntry 28 } qtechfrExtCircuitRcvDataRate OBJECT-TYPE SYNTAX INTEGER (1..45000000) MAX-ACCESS read-only STATUS current DESCRIPTION "The average rate (bytes/second) at which data is received in this circuit. " ::= { qtechfrExtCircuitEntry 29 } qtechfrExtCircuitRcvPktRate OBJECT-TYPE SYNTAX INTEGER (1..45000000) MAX-ACCESS read-only STATUS current DESCRIPTION "The average number of packets received in a second in this circuit. " ::= { qtechfrExtCircuitEntry 30 } -- end circuit subgroup } -- Mapping sub-group { qtechfrMapTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechfrMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of protocols and addresses mapping information of FR virtual circuit." ::= { qtechfrMapObjs 1 } qtechfrMapEntry OBJECT-TYPE SYNTAX QtechfrMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry of the table contains one mapping information of a Frame Relay virtual circuit." INDEX { frCircuitIfIndex, frCircuitDlci, qtechfrMapIndex } ::= { qtechfrMapTable 1 } QtechfrMapEntry ::= SEQUENCE { qtechfrMapIndex INTEGER, qtechfrMapProtocol QtechfrMapProtocols, qtechfrMapAddress OCTET STRING (SIZE(0..64)), qtechfrMapType INTEGER, qtechfrMapEncaps INTEGER, qtechfrMapBroadcast TruthValue, qtechfrMapPayloadCompress TruthValue, qtechfrMapTcpHdrCompress INTEGER, qtechfrMapRtpHdrCompress INTEGER, qtechfrMapPayloadCompressType INTEGER } qtechfrMapIndex OBJECT-TYPE SYNTAX INTEGER (1..999) MAX-ACCESS read-only STATUS current DESCRIPTION "An arbitrary Index to the mapping information associated with a certain circuit. The maximum value is arbitrarily picked which is considered sufficient for usual configuration." ::= { qtechfrMapEntry 1 } qtechfrMapProtocol OBJECT-TYPE SYNTAX QtechfrMapProtocols MAX-ACCESS read-only STATUS current DESCRIPTION "Mapping protocol for this circuit." ::= { qtechfrMapEntry 2 } qtechfrMapAddress OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Mapping protocol address at remote end for this DLCI. NOTE: For point-to-point DLCI, the string is fixed to be point-to-point." ::= { qtechfrMapEntry 3 } qtechfrMapType OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2), svc(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type for the map creation." ::= { qtechfrMapEntry 4 } qtechfrMapEncaps OBJECT-TYPE SYNTAX INTEGER { ietf(1), -- following IETF specifications -- (RFC 1490 as up to date) cisco(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indication of the encapsulation type for this mapping protocol." ::= { qtechfrMapEntry 5 } qtechfrMapBroadcast OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Broadcast enabled or disabled." ::= { qtechfrMapEntry 6 } qtechfrMapPayloadCompress OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS deprecated -- obsoleted by qtechfrMapPayloadCompressType DESCRIPTION "Indicate if payload compression is enabled." ::= { qtechfrMapEntry 7 } qtechfrMapTcpHdrCompress OBJECT-TYPE SYNTAX INTEGER { inapplicable(1), passive(2), active(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "TCP header compression type, if applicable." ::= { qtechfrMapEntry 8 } qtechfrMapRtpHdrCompress OBJECT-TYPE SYNTAX INTEGER { inapplicable(1), passive(2), active(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "RTP header compression type, if applicable. The value 'passive' means that the header of an outgoing RTP/IP packet is compressed only if an incoming RTP/IP packet had a compressed header. The value 'active' means the header of every outgoing RTP/IP packet is compressed." ::= { qtechfrMapEntry 9 } qtechfrMapPayloadCompressType OBJECT-TYPE SYNTAX INTEGER { inapplicable(1), cisco(2), -- cisco proprietary FR packet- -- by-packet payload compression frf9Software(3), -- FRF.9 software payload compression frf9Hardware(4) -- FRF.9 hardware payload compression } MAX-ACCESS read-only STATUS current DESCRIPTION "FR payload compression type, if applicable. FRF.9 is the Frame Relay Forum Implementation Agreement on FR payload compression. The compression can be done by either software or hardware (when equipped with the supporting hardware), depending on configuration." REFERENCE "Frame Relay Forum document number FRF.9" ::= { qtechfrMapEntry 10 } -- end mapping subgroup } -- SVC sub-group { -- containing SVC spcific information qtechfrSvcTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechfrSvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of FR SVC specific, descriptive and statistics information." ::= { qtechfrSvcObjs 1 } qtechfrSvcEntry OBJECT-TYPE SYNTAX QtechfrSvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry of the table contains circuit information specific to a Frame Relay Switched Virtual Circuit." INDEX { frCircuitIfIndex, frCircuitDlci } ::= { qtechfrSvcTable 1 } QtechfrSvcEntry ::= SEQUENCE { qtechfrSvcAddrLocal OCTET STRING (SIZE(0..64)), qtechfrSvcAddrRemote OCTET STRING (SIZE(0..64)), qtechfrSvcThroughputIn Integer32, qtechfrSvcMinThruputOut Integer32, qtechfrSvcMinThruputIn Integer32, qtechfrSvcCommitBurstIn Integer32, qtechfrSvcExcessBurstIn Integer32, qtechfrSvcIdleTime Integer32 } -- For circuit (DLCI) outbound throughput and outbound Committed -- and Excess Burst size, please refer to the following from -- RFC1315 respectively: -- frCircuitThroughput, -- frCircuitCommittedBurst, and -- frCircuitExcessBurst qtechfrSvcAddrLocal OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Local E.164/X.125 address for the circuit." ::= { qtechfrSvcEntry 1 } qtechfrSvcAddrRemote OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Remote E.164/X.125 address for the circuit." ::= { qtechfrSvcEntry 2 } qtechfrSvcThroughputIn OBJECT-TYPE SYNTAX Integer32 (9600..1544000) UNITS "bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "Circuit's incoming throughput. For outgoing throughput (commonly referred to as CIR) see frCircuitThroughput per RFC1315." ::= { qtechfrSvcEntry 3 } qtechfrSvcMinThruputOut OBJECT-TYPE SYNTAX Integer32 (9600..1544000) UNITS "bits per second" MAX-ACCESS read-only STATUS deprecated -- deprecated by -- cfrExtCircuitMinThruputOut DESCRIPTION "Circuit's outgoing minimal Throughput." ::= { qtechfrSvcEntry 4 } qtechfrSvcMinThruputIn OBJECT-TYPE SYNTAX Integer32 (9600..1544000) UNITS "bits per second" MAX-ACCESS read-only STATUS deprecated -- deprecated by -- cfrExtCircuitMinThruputIn DESCRIPTION "Circuit's incoming minimal Throughput." ::= { qtechfrSvcEntry 5 } qtechfrSvcCommitBurstIn OBJECT-TYPE SYNTAX Integer32 (9600..1544000) MAX-ACCESS read-only STATUS current DESCRIPTION "Circuit's incoming Committed Burst Rate. See ANSI and/or ITU specifications for definition and calculations. For outgoing CBR, see frCircuitCommittedBurst per RFC 1315." ::= { qtechfrSvcEntry 6 } qtechfrSvcExcessBurstIn OBJECT-TYPE SYNTAX Integer32 (9600..2440000) MAX-ACCESS read-only STATUS current DESCRIPTION "Circuit's incoming Excess Burst Rate. See ANSI and/or ITU specifications for definition and calculations. For outgoing EBR, see frCircuitExcessBurst per RFC 1315." ::= { qtechfrSvcEntry 7 } qtechfrSvcIdleTime OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Circuit's idle time period. If expires, the circuit is cleared." ::= { qtechfrSvcEntry 8 } -- end SVC subgroup } -- Enhanced Link Management Interface(ELMI) sub-group { -- ELMI is the protocol that learns QOS parameters(CIR,Bc,Be etc) -- of a VC from the switch. -- This sub group contains ELMI specific information. qtechfrElmiIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the Management address of the device used for address registration. Network management station can send management messages to this IP address. This can be user configured address or the address of one of the interfaces on the device. If address registration is disabled then this will have a value of 0.0.0.0. This object is accessible only if the ELMI protocol is supported on the device" ::= { qtechfrElmiObjs 1 } qtechfrElmiTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechfrElmiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of QTECH Frame Relay ELMI information that is specific to QTECH implementation" ::= { qtechfrElmiObjs 2 } qtechfrElmiEntry OBJECT-TYPE SYNTAX QtechfrElmiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry of the table contains information about a physical interface. The table can be accessible only if the device supports ELMI protocol and if LMI is enabled on the interface." INDEX { ifIndex } ::= { qtechfrElmiTable 1 } QtechfrElmiEntry ::= SEQUENCE { qtechfrElmiLinkStatus INTEGER, qtechfrElmiArStatus INTEGER, qtechfrElmiRemoteStatus INTEGER } qtechfrElmiLinkStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This variable states whether Enhanced Link Management Interface(ELMI) protocol is enabled or not on a frame relay interface." ::= { qtechfrElmiEntry 1 } qtechfrElmiArStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This variable states whether the Enhanced Link Management Interface(ELMI) address registration(AR) mechanism is enabled or not on a frame relay interface. A value of 1 indicates ELMI AR is supported on the interface. A value of 2 indicates ELMI AR is supported but the user disabled the exchange of IP address and ifIndex with the neighboring device. This object doesn't have any significance if cfrElmiLinkStatus is disabled on the interface." ::= { qtechfrElmiEntry 2 } qtechfrElmiRemoteStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This variable states the Enhanced Link Management(ELMI) status on the other end of the interface. If cfrElmiLinkStatus is enabled on the other end a value of 1 will be returned, else 2 will be returned. This object doesn't have any significance if cfrElmiLinkStatus is disabled on the interface" ::= { qtechfrElmiEntry 3 } qtechfrElmiNeighborTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechfrElmiNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of QTECH Frame Relay Neighbor ELMI information that is specific to QTECH implementation." ::= { qtechfrElmiObjs 3 } qtechfrElmiNeighborEntry OBJECT-TYPE SYNTAX QtechfrElmiNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry of the table contains information of the neighboring device connected to a physical interface. The entry will be present only if ELMI is enabled on the neighboring device interface. If the value of the qtechfrElmiRemoteStatus in the qtechfrElmiEntry is 1 then a valid entry exists for the interface. If ELMI is not supported on the remote end then, the neighbor information for the interface will not be present" INDEX { ifIndex } ::= { qtechfrElmiNeighborTable 1 } QtechfrElmiNeighborEntry ::= SEQUENCE { qtechfrElmiNeighborArStatus INTEGER, qtechfrElmiNeighborIpAddress IpAddress, qtechfrElmiNeighborIfIndex InterfaceIndex, qtechfrElmiNeighborVendorName DisplayString, qtechfrElmiNeighborPlatformName DisplayString, qtechfrElmiNeighborDeviceName DisplayString } qtechfrElmiNeighborArStatus OBJECT-TYPE SYNTAX INTEGER { notsupported(1), enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the status of ELMI Address registration(AR) on the neighboring device. A value of 1 indicates ELMI AR is not supported on the neighboring device. A value of 2 indicates ELMI AR is enabled on the interface. A value of 3 indicates AR is supported, but user disabled the exchange of IP address and ifIndex with the neighbor." ::= { qtechfrElmiNeighborEntry 1 } qtechfrElmiNeighborIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Management IP address of the neighboring device to which the other end of this interface is connected. Network management system can use this address to send management messages to the device. If address registration is not supported on the remote end then the value will be 0.0.0.0. NMS uses this object in the topology discovery of the network." ::= { qtechfrElmiNeighborEntry 2 } qtechfrElmiNeighborIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The Interface index of the neighboring device to which this interface is connected. If the value of qtechfrElmiNeighborArStatus is 2 then this will have a valid value. If the value of qtechfrElmiNeighborArStatus is 3 or 1 then value of this object will be 0. NMS uses this object in the topology discovery of the network." ::= { qtechfrElmiNeighborEntry 3 } qtechfrElmiNeighborVendorName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Vendor name of the neighboring device to which the other end of this interface is connected." ::= { qtechfrElmiNeighborEntry 4 } qtechfrElmiNeighborPlatformName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Platform name of the neighboring device to which the other end of this interface is connected." ::= { qtechfrElmiNeighborEntry 5 } qtechfrElmiNeighborDeviceName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Device name of the neighboring device to which the other end of this interface is connected." ::= { qtechfrElmiNeighborEntry 6 } -- end ELMI sub-group } -- Fragmentation sub-group { qtechfrFragTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechfrFragEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of Frame Relay Fragmentation information. These are specific to Qtech's implementation." ::= { qtechfrFragObjs 1 } qtechfrFragEntry OBJECT-TYPE SYNTAX QtechfrFragEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry of the table contains details of fragmentation configured on this circuit. " INDEX { frCircuitIfIndex, frCircuitDlci} ::= { qtechfrFragTable 1 } QtechfrFragEntry ::= SEQUENCE { qtechfrFragSize INTEGER, qtechfrFragType DisplayString, qtechfrFragInPkts Counter32, qtechfrFragOutPkts Counter32, qtechfrFragInOctets Counter32, qtechfrFragOutOctets Counter32, qtechfrFragNotInPkts Counter32, qtechfrFragNotOutPkts Counter32, qtechfrFragNotInOctets Counter32, qtechfrFragNotOutOctets Counter32, qtechfrFragAssembledInPkts Counter32, qtechfrFragAssembledInOctets Counter32, qtechfrFragPreOutPkts Counter32, qtechfrFragPreOutOctets Counter32, qtechfrFragDroppedReAssembledInPkts Counter32, qtechfrFragDroppedFragmentedOutPkts Counter32, qtechfrFragTimeoutsIn INTEGER, qtechfrFragOutOfSeqFragPkts Counter32, qtechfrFragUnexpectedBBitSetPkts Counter32, qtechfrFragSeqMissedPkts Counter32, qtechfrFragInterleavedOutPkts Counter32 } qtechfrFragSize OBJECT-TYPE SYNTAX INTEGER (16..1600) UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "qtechfrFragSize defines the payload size of a fragment and it excludes the FR headers and any FR fragmentation header." ::= { qtechfrFragEntry 1 } qtechfrFragType OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Fragmentation type configured by the user. The types supported are end-to-end, VoFR-qtech and VoFR." ::= { qtechfrFragEntry 2 } qtechfrFragInPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of frames received that have a fragmentation header." ::= { qtechfrFragEntry 3 } qtechfrFragOutPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of fragments that are transmitted with a fragmenation header." ::= { qtechfrFragEntry 4 } qtechfrFragInOctets OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes received in frames that have a fragmentation header. The number of bytes include the FR header." ::= { qtechfrFragEntry 5} qtechfrFragOutOctets OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes that are transmitted in frames with a fragmenation header. The number of bytes also includes the FR header." ::= { qtechfrFragEntry 6} qtechfrFragNotInPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of frames received that do not require reassembly and therefore will not contain the fragmentation header. This counter is valid only when end-to-end fragmentation type is set." ::= { qtechfrFragEntry 7} qtechfrFragNotOutPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of frames transmitted without fragmenting and therefore will not contain the fragmentation header. This counter is valid only when end-to-end fragmentation type is set." ::= { qtechfrFragEntry 8} qtechfrFragNotInOctets OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes received in frames that do not require reassembly and therefore will not contain the fragmentation header. This counter is valid only when end-to-end fragmentation type is set." ::= { qtechfrFragEntry 9} qtechfrFragNotOutOctets OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes transmitted in frames that are not fragmented and therefore will not contain the fragmentation header. This counter is valid only when end-to-end fragmentation type is set." ::= { qtechfrFragEntry 10} qtechfrFragAssembledInPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of fully reassembled frames. It also counts the number of packets received without FR fragmentation header (i.e. in un-fragmentated pkts)." ::= { qtechfrFragEntry 11} qtechfrFragAssembledInOctets OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes received in fully reassembled frames. It also counts the number of packets received without FR fragmentation header (i.e.in un-fragmentated pkts)." ::= { qtechfrFragEntry 12} qtechfrFragPreOutPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of frames fragmented and trasmitted. It also counts the number of packets trasmitted without FR fragmentation header (i.e. in un-fragmentated pkts)." ::= { qtechfrFragEntry 13} qtechfrFragPreOutOctets OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes transmitted in fragmented frames. It also counts the number of bytes trasmitted in frames without FR fragmentation header (i.e. in un-fragmentated pkts)." ::= { qtechfrFragEntry 14} qtechfrFragDroppedReAssembledInPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received fragments dropped for reasons such as : running out of memory, receiving segments out of sequence, receiving an unexpected frame with a B bit set, timing out on a reassembling frame." ::= { qtechfrFragEntry 15} qtechfrFragDroppedFragmentedOutPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments dropped because of running out of memory." ::= { qtechfrFragEntry 16} qtechfrFragTimeoutsIn OBJECT-TYPE SYNTAX INTEGER (0..1000) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of reassemble timer timeouts for this circuit. A frame requiring more than two minutes to fully reassemble is dropped and timeout will be incremented by one." ::= { qtechfrFragEntry 17} qtechfrFragOutOfSeqFragPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the total number of packets received with an unexpected sequence number. All fragments being reassembled are dropped. Start a new packet with the received segment only if the B bit is set on the segment. Otherwise the new segment is also dropped." ::= { qtechfrFragEntry 18} qtechfrFragUnexpectedBBitSetPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received in this circuit with a B bit set. All fragments being reassembled are dropped and a new packet is started with this segment." ::= { qtechfrFragEntry 19} qtechfrFragSeqMissedPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of fragments received in this circuit with skipped sequence number." ::= { qtechfrFragEntry 20} qtechfrFragInterleavedOutPkts OBJECT-TYPE SYNTAX Counter32 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets that have been interleaved between segments." ::= { qtechfrFragEntry 21} -- end Fragmentation sub-group } -- Connect sub-group { qtechfrConnectionTable OBJECT-TYPE SYNTAX SEQUENCE OF QtechfrConnectionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of Frame Relay/Frame Relay and Frame Relay/ATM Network/Service Interworking connection information. These are specific to Qtech's implementation." ::= { qtechfrConnectionObjs 1 } qtechfrConnectionEntry OBJECT-TYPE SYNTAX QtechfrConnectionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry of the table contains information of a connection that is established for Frame Relay/Frame Relay and Frame Relay/ATM Network/Service Interworking." INDEX { frCircuitIfIndex, frCircuitDlci} ::= { qtechfrConnectionTable 1 } QtechfrConnectionEntry ::= SEQUENCE { qtechfrConnName DisplayString, qtechfrConnID INTEGER, qtechfrConnState DisplayString, qtechfrConnSegment1Name DisplayString, qtechfrConnSegment1VCGroup DisplayString, qtechfrConnSegment1Dlci DlciNumber, qtechfrConnSegment2Name DisplayString, qtechfrConnSegment2Vpi INTEGER, qtechfrConnSegment2Vci INTEGER, qtechfrConnServiceTranslation INTEGER, qtechfrConnFrSscsDlci DlciNumber, qtechfrConnEfciBit INTEGER, qtechfrConnDeBit INTEGER, qtechfrConnClpBit INTEGER } qtechfrConnName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The textual name of a for FR/FR or FR/ATM Network/Service Interworking connection." ::= { qtechfrConnectionEntry 1 } qtechfrConnID OBJECT-TYPE SYNTAX INTEGER (1..2000) MAX-ACCESS read-only STATUS current DESCRIPTION "The numerical identifier of a FR/FR or FR/ATM Network/Service Interworking connection." ::= { qtechfrConnectionEntry 2 } qtechfrConnState OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Status of a FR/FR or FR/ATM Network/Service Interworking connection." ::= { qtechfrConnectionEntry 3} qtechfrConnSegment1Name OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The textual name used to identify the first segment of a FR/FR or FR/ATM Network/Service Interworking connection." ::= { qtechfrConnectionEntry 4} qtechfrConnSegment1VCGroup OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The textual name used to identify the VC-Group in the first segment of a Frame Relay/ATM Network Interworking (FRF.5)connection. This field is not applicabe in case of, FRF.8 (Frame Relay/ATM Service Interworking) and FR-FR connectione. " ::= { qtechfrConnectionEntry 5} qtechfrConnSegment1Dlci OBJECT-TYPE SYNTAX DlciNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The DLCI used as the first segment of a FR-FR or FR-ATM Network/Service Interworking connection." ::= { qtechfrConnectionEntry 6} qtechfrConnSegment2Name OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The interface on which second segment of a FR-FR or FR-ATM Network/Service Interworking connection is configured." ::= { qtechfrConnectionEntry 7} qtechfrConnSegment2Vpi OBJECT-TYPE SYNTAX INTEGER (0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of VPI, in the ATM connection, used as the second segment of a FR-ATM Network/Service Interworking connection. In case of FR-FR connection, the same will be used to display the DLCI used as the second segment." ::= { qtechfrConnectionEntry 8} qtechfrConnSegment2Vci OBJECT-TYPE SYNTAX INTEGER (0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of VCI, in the ATM connection, used as the second segment of a FR-ATM Network/Service Interworking connection. In case of FR-FR connection, this is not supported." ::= { qtechfrConnectionEntry 9} qtechfrConnServiceTranslation OBJECT-TYPE SYNTAX INTEGER { serviceTranslationEnabled(1), serviceTranslationNotEnabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Shows whether Service Translation Mode is supported or not. Translation Mode is the interworking of internetworking (routed and/or bridged) protocols used in FR-ATM Service PVC Interworking(FRF.8). This is not supported in case of FRF.5 (FR-ATM network Interworking) and FR-FR connections." ::= { qtechfrConnectionEntry 10} qtechfrConnFrSscsDlci OBJECT-TYPE SYNTAX DlciNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The DLCI value used at the FR-SSCS layer. This is one of connection multiplexing methods used in Frame Relay/ATM Network Interworking. Not supported in case of FRF.8 (FR-ATM Service PVC Interworking) and FR-FR connections" ::= { qtechfrConnectionEntry 11} qtechfrConnEfciBit OBJECT-TYPE SYNTAX INTEGER { mapFecn(1), notMapFecn(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Shows whether the FECN field in the FR frame is mapped to the ATM EFCI field of every cell generated out of the FR frame. This is used to indicate congestion in FR to ATM direction in case of Frame Relay/ATM Service PVC Interworking. Not supported in FRF.5 (Frame Relay/ATM Network Interworking and FR-FR connections." ::= { qtechfrConnectionEntry 12} qtechfrConnDeBit OBJECT-TYPE SYNTAX INTEGER { noMapClp(1), mapClp(2), setDe0(3), setDe1(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The method of operation for loss priority mapping in the B-ISDN to FR direction.. Not supported in case of FR-FR connection." ::= { qtechfrConnectionEntry 13} qtechfrConnClpBit OBJECT-TYPE SYNTAX INTEGER { setClpTo0AndCopyDeToFrsscsDe(1), setClpTo1AndCopyDeToFrsscsDe(2), copyDeToFrsscsDeAndClp(3), copyDeToClp(4), setClp1(5), setClp0(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The method of operation used to map loss priority mapping in the FR to ATM direction. Not supported in case of FR-FR connection." ::= { qtechfrConnectionEntry 14} -- end Conn subgroup } qtechFrMIBConformance OBJECT IDENTIFIER ::= { qtechFrameRelayMIB 3 } qtechFrMIBCompliances OBJECT IDENTIFIER ::= { qtechFrMIBConformance 1 } qtechFrMIBGroups OBJECT IDENTIFIER ::= { qtechFrMIBConformance 2 } qtechFrMIBCompliance MODULE-COMPLIANCE STATUS obsolete -- obsoleted by qtechFrMIBCompliancesRev2 DESCRIPTION "The compliance statement for entities which implement this Qtech Frame Relay MIB." MODULE -- this module MANDATORY-GROUPS { qtechFrMIBGroup } ::= { qtechFrMIBCompliances 1 } qtechFrMIBCompliancesRev1 MODULE-COMPLIANCE STATUS obsolete -- obsoleted by qtechFrMIBCompliancesRev2 DESCRIPTION "The compliance statement for entities which implement this Qtech Frame Relay MIB." MODULE -- this module MANDATORY-GROUPS { qtechFrMIBGroupRev1 } ::= { qtechFrMIBCompliances 2 } qtechFrMIBCompliancesRev2 MODULE-COMPLIANCE STATUS obsolete -- obsoleted by qtechFrMIBCompliancesRev3 DESCRIPTION "The compliance statement for entities which implement this Qtech Frame Relay MIB." MODULE -- this module MANDATORY-GROUPS { qtechFrLmiMIBGroup, qtechFrCircuitMIBGroup, qtechExtCircuitMIBGroup, qtechFrTsMIBGroup, qtechFrMapMIBGroup, qtechFrSvcMIBGroup } ::= { qtechFrMIBCompliances 3 } qtechFrMIBCompliancesRev3 MODULE-COMPLIANCE STATUS deprecated -- deprecated by qtechFrMIBCompliancesRev4 DESCRIPTION "The compliance statement for entities which implement this Qtech Frame Relay MIB." MODULE -- this module MANDATORY-GROUPS { qtechFrLmiMIBGroup, qtechFrCircuitMIBGroup, qtechExtCircuitMIBGroup, qtechFrTsMIBGroup, qtechFrMapMIBGroup, qtechFrSvcMIBGroup, qtechFrElmiMIBGroup} ::= { qtechFrMIBCompliances 4 } qtechFrMIBCompliancesRev4 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement this qtech Frame Relay MIB." MODULE -- this module MANDATORY-GROUPS { qtechFrLmiMIBGroup, qtechFrCircuitMIBGroup, qtechExtCircuitMIBGroup1, qtechFrTsMIBGroup, qtechFrMapMIBGroup, qtechFrSvcMIBGroup, qtechFrElmiMIBGroup1, qtechFrFragMIBGroup, qtechFrConnMIBGroup} ::= { qtechFrMIBCompliances 5 } -- units of conformance: qtechFrMIBGroup OBJECT-GROUP OBJECTS { qtechfrLmiLinkstatus, qtechfrLmiLinkType, qtechfrLmiEnquiryIns, qtechfrLmiEnquiryOuts, qtechfrLmiStatusIns, qtechfrLmiStatusOuts, qtechfrLmiUpdateStatusIns, qtechfrLmiUpdateStatusOuts, qtechfrLmiStatusTimeouts, qtechfrLmiStatusEnqTimeouts, qtechfrLmiN392Dce, qtechfrLmiN393Dce, qtechfrLmiT392Dce, qtechfrCircuitDEins, qtechfrCircuitDEouts, qtechfrCircuitDropPktsOuts, qtechfrCircuitType, qtechfrExtCircuitIfName, qtechfrExtCircuitIfType, qtechfrExtCircuitSubifIndex, qtechfrExtCircuitMapStatus, qtechfrExtCircuitCreateType, qtechfrExtCircuitMulticast, qtechfrExtCircuitRoutedDlci, qtechfrExtCircuitRoutedIf, qtechfrMapIndex, qtechfrMapProtocol, qtechfrMapAddress, qtechfrMapType, qtechfrMapEncaps, qtechfrMapBroadcast, qtechfrMapPayloadCompress, qtechfrMapTcpHdrCompress, qtechfrSvcAddrLocal, qtechfrSvcAddrRemote, qtechfrSvcThroughputIn, qtechfrSvcMinThruputOut, qtechfrSvcMinThruputIn, qtechfrSvcCommitBurstIn, qtechfrSvcExcessBurstIn, qtechfrSvcIdleTime } STATUS deprecated -- obsoleted by qtechFrMIBGroupRev1 DESCRIPTION "The compliance statement for entities which implement this Qtech Frame Relay MIB." ::= { qtechFrMIBGroups 1 } qtechFrMIBGroupRev1 OBJECT-GROUP OBJECTS { qtechfrLmiLinkstatus, qtechfrLmiLinkType, qtechfrLmiEnquiryIns, qtechfrLmiEnquiryOuts, qtechfrLmiStatusIns, qtechfrLmiStatusOuts, qtechfrLmiUpdateStatusIns, qtechfrLmiUpdateStatusOuts, qtechfrLmiStatusTimeouts, qtechfrLmiStatusEnqTimeouts, qtechfrLmiN392Dce, qtechfrLmiN393Dce, qtechfrLmiT392Dce, qtechfrCircuitDEins, qtechfrCircuitDEouts, qtechfrCircuitDropPktsOuts, qtechfrCircuitType, qtechfrExtCircuitIfName, qtechfrExtCircuitIfType, qtechfrExtCircuitSubifIndex, qtechfrExtCircuitMapStatus, qtechfrExtCircuitCreateType, qtechfrExtCircuitMulticast, qtechfrExtCircuitRoutedDlci, qtechfrExtCircuitRoutedIf, qtechfrExtCircuitUncompressIns, qtechfrExtCircuitUncompressOuts, qtechfrMapIndex, qtechfrMapProtocol, qtechfrMapAddress, qtechfrMapType, qtechfrMapEncaps, qtechfrMapBroadcast, -- removed qtechfrMapPayloadCompress, obsoleted by qtechfrMapPayloadCompressType qtechfrMapTcpHdrCompress, qtechfrMapRtpHdrCompress, qtechfrMapPayloadCompressType, qtechfrSvcAddrLocal, qtechfrSvcAddrRemote, qtechfrSvcThroughputIn, qtechfrSvcMinThruputOut, qtechfrSvcMinThruputIn, qtechfrSvcCommitBurstIn, qtechfrSvcExcessBurstIn, qtechfrSvcIdleTime } STATUS deprecated DESCRIPTION "A collection of objects providing router's Frame Relay configuration and statistics information that are additional to the IETF standard Frame Relay DTE MIB." ::= { qtechFrMIBGroups 2 } qtechFrLmiMIBGroup OBJECT-GROUP OBJECTS { qtechfrLmiLinkstatus, qtechfrLmiLinkType, qtechfrLmiEnquiryIns, qtechfrLmiEnquiryOuts, qtechfrLmiStatusIns, qtechfrLmiStatusOuts, qtechfrLmiUpdateStatusIns, qtechfrLmiUpdateStatusOuts, qtechfrLmiStatusTimeouts, qtechfrLmiStatusEnqTimeouts, qtechfrLmiN392Dce, qtechfrLmiN393Dce, qtechfrLmiT392Dce } STATUS current DESCRIPTION "A collection of objects providing router's Frame Relay LMI configuration and statistics information either supplemental to the frDlcmiTable of RFC 1315 or specific to qtech's implementation." ::= { qtechFrMIBGroups 3 } qtechFrCircuitMIBGroup OBJECT-GROUP OBJECTS { qtechfrCircuitDEins, qtechfrCircuitDEouts, qtechfrCircuitDropPktsOuts, qtechfrCircuitType } STATUS current DESCRIPTION "A collection of objects providing information of a circuit that are not included in frCircuitTable of RFC1315 but are generic to Frame Relay." ::= { qtechFrMIBGroups 4 } qtechExtCircuitMIBGroup OBJECT-GROUP OBJECTS { qtechfrExtCircuitIfName, qtechfrExtCircuitIfType, qtechfrExtCircuitSubifIndex, qtechfrExtCircuitMapStatus, qtechfrExtCircuitCreateType, qtechfrExtCircuitMulticast, qtechfrExtCircuitRoutedDlci, qtechfrExtCircuitRoutedIf, qtechfrExtCircuitUncompressIns, qtechfrExtCircuitUncompressOuts, qtechfrExtCircuitFECNOuts, qtechfrExtCircuitBECNOuts, qtechfrExtCircuitMinThruputOut, qtechfrExtCircuitMinThruputIn, qtechfrExtCircuitBcastPktOuts, qtechfrExtCircuitBcastByteOuts, qtechfrExtCircuitBandwidth } STATUS deprecated DESCRIPTION "A collection of objects that provide qtech implementation specific FR circuit information. This is a qtech extension for the frCircuitTable of RFC 1315." ::= { qtechFrMIBGroups 5 } qtechExtCircuitMIBGroup1 OBJECT-GROUP OBJECTS { qtechfrExtCircuitIfName, qtechfrExtCircuitIfType, qtechfrExtCircuitSubifIndex, qtechfrExtCircuitMapStatus, qtechfrExtCircuitCreateType, qtechfrExtCircuitMulticast, qtechfrExtCircuitRoutedDlci, qtechfrExtCircuitRoutedIf, qtechfrExtCircuitUncompressIns, qtechfrExtCircuitUncompressOuts, qtechfrExtCircuitFECNOuts, qtechfrExtCircuitBECNOuts, qtechfrExtCircuitMinThruputOut, qtechfrExtCircuitMinThruputIn, qtechfrExtCircuitBcastPktOuts, qtechfrExtCircuitBcastByteOuts, qtechfrExtCircuitBandwidth, qtechfrExtCircuitTxDataRate, qtechfrExtCircuitTxPktRate, qtechfrExtCircuitRcvDataRate, qtechfrExtCircuitRcvPktRate } STATUS current DESCRIPTION "A collection of objects that provide qtech implementation specific FR circuit information. This is a qtech extension for the frCircuitTable of RFC 1315." ::= { qtechFrMIBGroups 13 } qtechFrTsMIBGroup OBJECT-GROUP OBJECTS { qtechfrExtCircuitShapeByteLimit, qtechfrExtCircuitShapeInterval, qtechfrExtCircuitShapeByteIncrement, qtechfrExtCircuitShapePkts, qtechfrExtCircuitShapeBytes, qtechfrExtCircuitShapePktsDelay, qtechfrExtCircuitShapeBytesDelay, qtechfrExtCircuitShapeActive, qtechfrExtCircuitShapeAdapting } STATUS current DESCRIPTION "A collection of objects that provide information about Frame Relay Traffic Shaping. These are additional to the IETF standard Frame Relay DTE MIB." ::= { qtechFrMIBGroups 6 } qtechFrMapMIBGroup OBJECT-GROUP OBJECTS { qtechfrMapIndex, qtechfrMapProtocol, qtechfrMapAddress, qtechfrMapType, qtechfrMapEncaps, qtechfrMapBroadcast, qtechfrMapTcpHdrCompress, qtechfrMapRtpHdrCompress, qtechfrMapPayloadCompressType } STATUS current DESCRIPTION "A collection of objects to provide mapping information of a Frame Relay virtual circuit. These are additional to the IETF standard Frame Relay DTE MIB." ::= { qtechFrMIBGroups 7 } qtechFrSvcMIBGroup OBJECT-GROUP OBJECTS { qtechfrSvcAddrLocal, qtechfrSvcAddrRemote, qtechfrSvcThroughputIn, qtechfrSvcCommitBurstIn, qtechfrSvcExcessBurstIn, qtechfrSvcIdleTime } STATUS current DESCRIPTION "A collection of objects to provide circuit information specific to a Frame Relay Switched Virtual Circuit.This is in addition to the IETF standard Frame Relay DTE MIB." ::= { qtechFrMIBGroups 8 } qtechFrElmiMIBGroup OBJECT-GROUP OBJECTS { qtechfrElmiIpAddr, qtechfrElmiArStatus, qtechfrElmiRemoteStatus, qtechfrElmiNeighborArStatus, qtechfrElmiNeighborIpAddress, qtechfrElmiNeighborIfIndex, qtechfrElmiNeighborVendorName, qtechfrElmiNeighborPlatformName, qtechfrElmiNeighborDeviceName } STATUS deprecated DESCRIPTION "A collection of objects providing router's ELMI information." ::= { qtechFrMIBGroups 9 } qtechFrElmiMIBGroup1 OBJECT-GROUP OBJECTS { qtechfrElmiIpAddr, qtechfrElmiArStatus, qtechfrElmiRemoteStatus, qtechfrElmiNeighborArStatus, qtechfrElmiNeighborIpAddress, qtechfrElmiNeighborIfIndex, qtechfrElmiNeighborVendorName, qtechfrElmiNeighborPlatformName, qtechfrElmiNeighborDeviceName, qtechfrElmiLinkStatus } STATUS current DESCRIPTION "A collection of objects providing router's ELMI information." ::= { qtechFrMIBGroups 10 } qtechFrFragMIBGroup OBJECT-GROUP OBJECTS { qtechfrFragSize, qtechfrFragType, qtechfrFragInPkts, qtechfrFragOutPkts, qtechfrFragInOctets, qtechfrFragOutOctets, qtechfrFragNotInPkts, qtechfrFragNotOutPkts, qtechfrFragNotInOctets, qtechfrFragNotOutOctets, qtechfrFragAssembledInPkts, qtechfrFragAssembledInOctets, qtechfrFragPreOutPkts, qtechfrFragPreOutOctets, qtechfrFragDroppedReAssembledInPkts, qtechfrFragDroppedFragmentedOutPkts, qtechfrFragTimeoutsIn, qtechfrFragOutOfSeqFragPkts, qtechfrFragUnexpectedBBitSetPkts, qtechfrFragSeqMissedPkts, qtechfrFragInterleavedOutPkts } STATUS current DESCRIPTION "A collection of objects providing router's fragmentation information." ::= { qtechFrMIBGroups 11 } qtechFrConnMIBGroup OBJECT-GROUP OBJECTS { qtechfrConnName, qtechfrConnID, qtechfrConnState, qtechfrConnSegment1Name, qtechfrConnSegment1VCGroup, qtechfrConnSegment1Dlci, qtechfrConnSegment2Name, qtechfrConnSegment2Vpi, qtechfrConnSegment2Vci, qtechfrConnServiceTranslation, qtechfrConnFrSscsDlci, qtechfrConnEfciBit, qtechfrConnDeBit, qtechfrConnClpBit } STATUS current DESCRIPTION "A collection of objects providing router's fragmentation information." ::= { qtechFrMIBGroups 12 } END