HpicfHighAvailability-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE, MODULE-IDENTITY, TimeTicks, Counter32, Unsigned32,Integer32 FROM SNMPv2-SMI OBJECT-GROUP, MODULE-COMPLIANCE FROM SNMPv2-CONF entPhysicalIndex,PhysicalIndex FROM ENTITY-MIB EntityStandbyStatus FROM ENTITY-STATE-MIB hpicfCommon FROM HP-ICF-OID; hpicfHighAvailability MODULE-IDENTITY LAST-UPDATED "201701050000Z" -- Jan 05 , 2017 ORGANIZATION "HP Networking" CONTACT-INFO "Hewlett-Packard Company 8000 Foothills Blvd. Roseville, CA 95747" DESCRIPTION "Management information for configuring Redundant Management module on Hewlett-Packard network devices." REVISION "201701050000Z" -- Jan 05 , 2017 DESCRIPTION "Added hpicfHAPreferredActiveManagement to hpicfHAConfigObjects. And added hpicfHAConfigGroup1 and deprecated hpicfHAConfigGroup and hpicfHACompliance" REVISION "201205150000Z" -- May 15 , 2012 DESCRIPTION "Added hpicfHAMgmtModuleBackUpState to the table hpicfHAMgmtModuleTable.Added hpicfHAMgmtModuleGroup, hpicfHACompliance2 and deprecated hpicfHAMgmtModuleGroup and hpicfHACompliance1." REVISION "200910180000Z" -- October 18, 2009 DESCRIPTION "Added hpicfHAFailOverLogTable and hpicfHAMgmtModuleTable." REVISION "200909060000Z" -- September 6, 2009 DESCRIPTION "Added hpicfHAContinuousFwdingTime and Removed hpicfHARedundancyWarmStandby scalar mib and added it as enum to hpicfHARedundancyManagementModuleMode." REVISION "200908210000Z" -- August 21,2009 DESCRIPTION "Added hpicfHARedundancyWarmStandby scalar mib." REVISION "200609050000Z" -- September 5, 2006 DESCRIPTION "Initial version of the MIB module." ::= { hpicfCommon 11 } -- ********************************************************************** -- The HP ICF High Availability MIB groups -- ********************************************************************** hpicfHAConfigObjects OBJECT IDENTIFIER ::= { hpicfHighAvailability 1} hpicfHAStatusObjects OBJECT IDENTIFIER ::= { hpicfHighAvailability 2} hpicfHAConformance OBJECT IDENTIFIER ::= { hpicfHighAvailability 3} --The HP ICF High Availability configuration group hpicfHARedundancyManagementModuleMode OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2), warmStandby (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specify to enable/disable this feature. Enabling allows for management module redundancy when there are two management modules in the switch and does a hitless failover. Disabling prevents redundancy except due to fatal hardware errors on one management module. warmStandby option does a non-hitless failover." ::= { hpicfHAConfigObjects 1 } hpicfHAContinuousFwdingTime OBJECT-TYPE SYNTAX Unsigned32 --(0..2147483647) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This is a configurable timer. After the failover, on the new AMM, the route and neighbor table entries are marked as stale in the FIB. As routing protocols begin to re-add routes, this stale flag will be reset. When this timer expires, all route and neighbor table entries still marked stale [not yet re-added] will be removed. A value of 0 means that no layer 3 hitless behavior is desired, and in this configuration, upon failover all FIB entries are flushed and corresponding hardware entries are removed. A default value of 5 minutes is chosen with the assumption that the routing protocols can finish re-adding the routes to the equivalent state within this time." DEFVAL { 300 } ::= { hpicfHAConfigObjects 2 } hpicfHAPreferredActiveManagement OBJECT-TYPE SYNTAX INTEGER { none (0), management-module1 (1), management-module2 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specify management module priority to specify Active management module across several reboot. The module is likely to become Active post reboot and Not instantaneously. The setting is applied to the running-configuration" DEFVAL { 0 } ::= { hpicfHAConfigObjects 3 } -- The HP ICF High Availability status group hpicfHAMgmtRedundancyFailureReason OBJECT-TYPE SYNTAX INTEGER { noRedundantModule (1), noFailure (2), unknownReason (3), mismatchOS (4), failedSelftest (5), communicationFailure (6), redundancyDisable (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the reason a redundant management module failed to become a standby module." ::= { hpicfHAStatusObjects 1 } hpicfHAMgmtFailovers OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the number of management module failovers since last chassis boot." ::= { hpicfHAStatusObjects 2 } hpicfHALastFailoverTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the time (in hundredths of a second) of the last management module failover." ::= {hpicfHAStatusObjects 3 } hpicfHAFailOverLogTable OBJECT-TYPE SYNTAX SEQUENCE OF HpicfHAFailOverLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains High Availability(HA) failover log specific information." ::= { hpicfHAStatusObjects 4} hpicfHAFailOverLogEntry OBJECT-TYPE SYNTAX HpicfHAFailOverLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Failover log information maintained for HA." INDEX { hpicfHAFailOverIndex } ::= { hpicfHAFailOverLogTable 1 } HpicfHAFailOverLogEntry ::= SEQUENCE { hpicfHAFailOverIndex Integer32, hpicfHAFailOverMgmtModule PhysicalIndex, hpicfHAFailOverState INTEGER, hpicfHAFailOverTime Integer32, hpicfHAFailOverReason INTEGER } hpicfHAFailOverIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object uniquely identifies the entries in the failover log table. This table contains maximum of recent 10 entries." ::= { hpicfHAFailOverLogEntry 1 } hpicfHAFailOverMgmtModule OBJECT-TYPE SYNTAX PhysicalIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This object displays the management module information.It is similar to entPhysicalIndex." ::= { hpicfHAFailOverLogEntry 2 } hpicfHAFailOverState OBJECT-TYPE SYNTAX INTEGER { unknown (1), active (2), standby (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the failover state. 'unknown' indicates the state of the management module is undefined and this resource is unable to report standby state. 'active' indicates the state of the management module as active module and it means the resource is providing service. 'standby' indicates that the management module is not providing service, but it will be immediately able to take over the role of the resource to be backed up, without the need for initialization activity, and will contain the same information as the resource to be backed up." ::= { hpicfHAFailOverLogEntry 3 } hpicfHAFailOverTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the failover time in seconds since 1/1/1990 0:0:0." ::= { hpicfHAFailOverLogEntry 4 } hpicfHAFailOverReason OBJECT-TYPE SYNTAX INTEGER { invalid (0), switchoverReq (1), buttonReq (2), crashReq(3), activeReset(4), altReset (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object define the reason for failover. 'switchoverReq' indicates failover as a result of switchover command issued by the user. 'buttonReq' indicates failover as a result of manual boot done by the user via reboot button. 'crashReq' indicates failover as a result of crash that happened to the active module. 'activeReset' indicates failover as a result of reset command issued by the user at active module. 'altReset' indicates failover as a result of reset command issued by the user at the alternate module. " ::= { hpicfHAFailOverLogEntry 5 } hpicfHAMgmtModuleTable OBJECT-TYPE SYNTAX SEQUENCE OF HpicfHAMgmtModuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains High Availability (HA) management module specific information." ::= { hpicfHAStatusObjects 5} hpicfHAMgmtModuleEntry OBJECT-TYPE SYNTAX HpicfHAMgmtModuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Management module information maintained for HA." INDEX { entPhysicalIndex } ::= { hpicfHAMgmtModuleTable 1 } HpicfHAMgmtModuleEntry ::= SEQUENCE { hpicfHAMgmtModuleState EntityStandbyStatus, hpicfHAMgmtModuleCardUpSince Integer32, hpicfHAMgmtModuleStateSince Integer32, hpicfHAMgmtModuleRedundancyState INTEGER, hpicfHAMgmtModuleBackUpState INTEGER } hpicfHAMgmtModuleState OBJECT-TYPE SYNTAX EntityStandbyStatus MAX-ACCESS read-only STATUS current DESCRIPTION "This object displays the state of the the management module.This object is similar to entStateStandby object." ::= { hpicfHAMgmtModuleEntry 1 } hpicfHAMgmtModuleCardUpSince OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object displays the card uptime in seconds since this module state. " ::= { hpicfHAMgmtModuleEntry 2 } hpicfHAMgmtModuleStateSince OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object displays time in seconds from which the current state is valid." ::= { hpicfHAMgmtModuleEntry 3} hpicfHAMgmtModuleRedundancyState OBJECT-TYPE SYNTAX INTEGER { unavailable (1), active (2), disabled (3), syncing (4), warmStandby (5), hitless (6) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the management module's redundancy state. 'unavailable' indicates the redundancy module is not available due to error or absence of the module. 'active' indicates the redundancy module is currently active and is providing service. 'disabled' indicates the redundancy module is disabled. 'syncing' indicates the redundancy module is in syncing state and after successful syncing it will enter active state else it will report error. 'warmStandby' indicates the redundancy module is in warmstandby mode and is not providing service, but it will be immediately able to take over the role of the resource to be backed up, without the need for initialization activity, and will contain the same information as the resource to be backed up but the Layer2 information will not be synced. 'hitless'indicates the redundancy module is in hitless mode and is not providing service, but it will be immediately able to take over the role of the resource to be backed up, without the need for initialization activity, and will contain the same information as the resource to be backed up." ::= { hpicfHAMgmtModuleEntry 4 } hpicfHAMgmtModuleBackUpState OBJECT-TYPE SYNTAX INTEGER { failed (0), unknown (1), waiting (2), realtimeBackupToSlot (3), slotIsAbsent (4), batchBackup (5), receivingRealtimeData (6), offline (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the management module's backup state. 'failed' indicates that the redundancy module has failed due to some communication failure or incompatible OS. 'unknown' indicates that the redundancy module is shutdown. 'waiting' indicates that the redundancy module is waiting for batch backup request. 'realtimeBackuptoSlot' indicates that the redundancy module is currently in active state and is providing service. 'slotIsAbsent' indicates that there is no redundant module due to error or absence of the redundancy module. 'batchBackup' indicates that the redundancy module is in syncing state and it enters the active state after successful syncing. 'receivingRealtimeData' indicates that the redundancy module is in standby state.'offline' indicates that the redundancy module is disabled." ::= { hpicfHAMgmtModuleEntry 5 } -- *********************************************************** -- -- hpicfHighAvailability M I B C O N F O R M A N C E -- -- *********************************************************** -- hpicfHACompliances OBJECT IDENTIFIER ::= { hpicfHAConformance 1 } hpicfHAGroups OBJECT IDENTIFIER ::= { hpicfHAConformance 2 } -- compliance statements hpicfHACompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "*********** THIS COMPLIANCE IS DEPRECATED ************ The compliance statement for SNMP entities which implement the hpicfHighAvailability MIB. This compliance section has been deprecated and replaced with hpicfHACompliance3" MODULE -- this module MANDATORY-GROUPS { hpicfHAConfigGroup, hpicfHAStatusGroup } ::= { hpicfHACompliances 1 } hpicfHACompliance1 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "*********** THIS COMPLIANCE IS DEPRECATED ************ The compliance statement for SNMP entities which implement the hpicfHighAvailability MIB. This compliance section has been deprecated and replaced with hpicfHACompliance2 ." MODULE -- this module MANDATORY-GROUPS { hpicfHAFailOverGroup , hpicfHAMgmtModuleGroup } ::= { hpicfHACompliances 2 } hpicfHACompliance2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which implement the hpicfHighAvailability MIB." MODULE -- this module MANDATORY-GROUPS { hpicfHAFailOverGroup , hpicfHAMgmtModuleGroup1 } ::= { hpicfHACompliances 3 } hpicfHACompliance3 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which implement the hpicfHighAvailability MIB." MODULE -- this module MANDATORY-GROUPS { hpicfHAConfigGroup1, hpicfHAStatusGroup } ::= { hpicfHACompliances 4 } -- MIB groupings hpicfHAConfigGroup OBJECT-GROUP OBJECTS { hpicfHARedundancyManagementModuleMode, hpicfHAContinuousFwdingTime } STATUS deprecated DESCRIPTION "********** THIS GROUP IS DEPRECATED *************** The collection of objects which are used to configure the Redundancy Management Module. This group has been deprecated and replaced with hpicfHAConfigGroup1 ." ::= { hpicfHAGroups 1 } hpicfHAStatusGroup OBJECT-GROUP OBJECTS { hpicfHAMgmtRedundancyFailureReason, hpicfHAMgmtFailovers, hpicfHALastFailoverTime } STATUS current DESCRIPTION "The collection of objects which are used to represent Management Module statistics information." ::= { hpicfHAGroups 2 } hpicfHAFailOverGroup OBJECT-GROUP OBJECTS { hpicfHAFailOverMgmtModule , hpicfHAFailOverState , hpicfHAFailOverTime , hpicfHAFailOverReason } STATUS current DESCRIPTION "The collection of objects which are used to represent failover log statistics information." ::= { hpicfHAGroups 3 } hpicfHAMgmtModuleGroup OBJECT-GROUP OBJECTS { hpicfHAMgmtModuleState , hpicfHAMgmtModuleCardUpSince , hpicfHAMgmtModuleStateSince , hpicfHAMgmtModuleRedundancyState } STATUS deprecated DESCRIPTION "********** THIS GROUP IS DEPRECATED *************** The collection of objects which are used to represent management module specific information. This group has been deprecated and replaced with hpicfHAMgmtModuleGroup1 ." ::= { hpicfHAGroups 4 } hpicfHAMgmtModuleGroup1 OBJECT-GROUP OBJECTS { hpicfHAMgmtModuleState, hpicfHAMgmtModuleCardUpSince, hpicfHAMgmtModuleStateSince, hpicfHAMgmtModuleRedundancyState, hpicfHAMgmtModuleBackUpState } STATUS current DESCRIPTION "The collection of objects which are used to represent management module specific information." ::= { hpicfHAGroups 5 } hpicfHAConfigGroup1 OBJECT-GROUP OBJECTS { hpicfHARedundancyManagementModuleMode, hpicfHAContinuousFwdingTime, hpicfHAPreferredActiveManagement } STATUS current DESCRIPTION "The collection of objects which are used to configure the Redundancy Management Module." ::= { hpicfHAGroups 6 } END